Download Sharp X-70H Service manual
Transcript
XL-60H/70H SERVICE MANUAL No. S4031XL60H/// XL-60H XL-70H Illustration: XL-60H XL-60H/XL-70H Micro Component System consisting of XL-60H/ XL-70H (main unit) and CP-XL60H/CP-XL70H (speaker system). • In the interests of user-safety the set should be restored to its original condition and only parts identical to those specified should be used. • Note for users in U.K. Recording and playback of any material may require consent, which SHARP is unable to give. Please refer particularly to the provisions of Copyright Act 1956, the Dramatic and Musical Performers Protection Act 1956, the Performers Protection Acts 1963 and 1972 and to any subsequent statutory enactments and orders. Illustration: XL-70H CONTENTS Page SAFETY PRECAUTION FOR SERVICE MANUAL .......................................................................................................... 2 IMPORTANT SERVICE NOTES (FOR U.K. ONLY) ......................................................................................................... 2 SPECIFICATIONS ............................................................................................................................................................ 3 NAMES OF PARTS .......................................................................................................................................................... 4 OPERATION MANUAL ..................................................................................................................................................... 6 DISASSEMBLY ................................................................................................................................................................. 8 REMOVING AND REINSTALLING THE MAIN PARTS .................................................................................................. 10 ADJUSTMENT ................................................................................................................................................................ 12 RDS ................................................................................................................................................................................ 13 TEST MODE ................................................................................................................................................................... 14 ERROR LIST .................................................................................................................................................................. 20 NOTES ON SCHEMATIC DIAGRAM ............................................................................................................................. 21 TYPE OF TRANSISTOR AND LED ................................................................................................................................ 21 BLOCK DIAGRAM .......................................................................................................................................................... 22 SCHEMATIC DIAGRAM ................................................................................................................................................. 26 WIRING SIDE OF P.W.BOARD ...................................................................................................................................... 32 WAVEFORMS OF CD CIRCUIT ..................................................................................................................................... 36 TROUBLESHOOTING .................................................................................................................................................... 37 FUNCTION TABLE OF IC .............................................................................................................................................. 43 LCD SEGMENT .............................................................................................................................................................. 52 PARTS GUIDE/EXPLODED VIEW PACKING METHOD (FOR U.K. ONLY) SHARP CORPORATION –1– This document has been published to be used for after sales service only. The contents are subject to change without notice. XL-60H/70H SAFETY PRECAUTION FOR SERVICE MANUAL Precaution to be taken when replacing and servicing the Laser Pickup. The AEL (Accessible Emission Level) of Laser Power Output for this model is specified to be lower than Class I Requirements. However, the following precautions must be observed during servicing to protect your eyes against exposure to the Laser beam (1) When the cabinet has been removed, the power is turned on without a compact disc, and the Pickup is on a position outer than the lead-in position, the Laser will light for several seconds to detect a disc. Do not look into the Pickup Lens. (2) The Laser Power Output of the Pickup inside the unit and replacement service parts have already been adjusted prior to shipping. (3) No adjustment to the Laser Power should be attempted when replacing or servicing the Pickup. (4) Under no circumstances look directly into the Pickup Lens at any time. (5) CAUTION - Use of controls or adjustments, or performance of procedures other than those specified herein may result in hazardous radiation exposure. Laser Diode Properties Material: GaAIAs Wavelength: 780 nm Emission Duration: continuous Laser Output: max. 0.6 mW VAROITUS! LAITTEEN KÄYTTÄMINEN MUULLA KUIN TÄSSÄ KÄYTTÖOHJEESSA MAI NI TULLA TAVALLA SAATTAA ALTI STAA KÄYTTÄJÄN TURVALLI SUUSLUOKAN 1 YLITTÄVÄLLE NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. VARNING - OM APPARATEN ANVÄNDS PÅ ANNAT SÄTT ÄN I DENNA BRUKSANVI SNI NG SPECI FI CERAS. KAN ANVÄNDAREN UTSÄTTAS FÖR OSYNLIG LASERSTRÅLNING, SOM ÖVERSKRIDER GRÄNSEN FÖR LASERKLASS 1. CAUTION-INVISIBLE LASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS. VARNING-OSYNLIG LASERSTRALNING NAR DENNA DEL AR OPPNAD. STIRRA EJ IN I STRALEN OCH BETRAKTA EJ STRALEN MED OPTISKA INSTRUMENT. ADVERSEL-USYNLIG LASERSTRALING VED ABNING. SE IKKE IND I STRALEN-HELLER IKKE MED OPTISKE INSTRUMENTER. VARO! AVATTAESSA OLET ALTTIINA NAKYMATON LASERSATEILYLLE. ALA TUIJOTA SATEESEEN ALAKA KATSO SITA OPTISEN LAITTEEN LAPI. VARNING-OSYNLIG LASERSTRALNING NAR DENNA DEL AR OPPNAD. STIRRA EJ IN I STRALEN OCH BETRAKTA EJ STRALEN GENOM OPTISKT INSTRUMENT. ADVERSEL-USYNLIG LASERSTRALING NAR DEKSEL APNES. STIRR IKKE INN I STRALEN ELLER SE DIREKTE MED OPTISKE INSTRUMENTER. LASER KLASSE 1 LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT CAUTION Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. As the laser beam used in this compact disc player is harmful to the eyes, do not attempt to disassemble the cabinet. Refer servicing to qualified personnel only. (For U.K. ) (For Europe) IMPORTANT SERVICE NOTES (FOR U.K. ONLY) Before returning the unit to the customer after completion of a repair or adjustment it is necessary for the following withstand voltage test to be applied to ensure the unit is safe for the customer to use. Setting of Withstanding Voltage Tester and set. Set name WITHSTANDING VOLTAGE TESTER set value Withstanding Voltage Tester Test voltage 4,240 VPEAK 3,000 VRMS Set time 6 secs Set current(Cutoff current) 4 mA PROBE AC OUT UNIT SHORT-CIRCUT AC POWER SUPPLY CORD Unit Judgment OK: The “GOOD” lamp lights. NG: The “NG” lamp lights and the buzzor sounds. –2– CONNECT THE PROBE TO GND OF CHASSIS SCREW TERMINAL XL-60H/70H FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER TO THE OPERATION MANUAL. SPECIFICATIONS XL-60H/70H ● Cassette deck section ● General Power source: Power consumption: Dimensions: Weight: Frequency response: AC 230 V, 50 Hz 50 - 14,000 Hz (Normal tape) 50 W Signal/noise ratio: 50 dB Width; 160 mm (6-5/16") Height; 241 mm (9-1/2") Depth; 298 mm (11-3/4") Wow and flutter: (For Europe) Wow and flutter: (For U.K.) 3.6 kg (7.9 lbs.) 0.3 % (DIN 45 511) 0.25 % (WRMS) ● Amplifier section Output power: (For Europe) ● Speaker section PMPO; 120 W (total) MPO; 60 W (30 W + 30 W) (DIN 45 324) RMS; 40 W (20 W + 20 W) (DIN 45 324) RMS; 40 W (20 W + 20 W) (10 % T.H.D.) CP-XL60H Type: Output power: (For U.K.) Output terminals: Speakers; 4 ohms Headphones; 16-50 ohms (recommended; 32 ohms) CD digital output (optical) Input terminals: Video/Auxiliary (audio signal); 500 mV/47 k ohms Rated input power: 20 W Maximum input power: 40 W Impedance: 4 ohms Dimensions: Width; 160 mm (6-5/16") Height; 240 mm (9-1/2") Depth; 190 mm (7-7/16") Weight: 1.8 kg (4.0 lbs.)/each ● Tuner section Frequency range: FM; 87.5-108 MHz AM; 522-1,620 kHz 2-way [10 cm (4") woofer and 1.5 cm (9/16") tweeter] CP-XL70H ● Compact disc player section Type: 2-way [10 cm (4") woofer and 2.5 cm (1") semi dome tweeter] Type: Compact disc player Signal readout: Non-contact, 3-beam semiconductor laser pickup D/A converter: 1-bit D/A converter Rated input power: 20 W Filter: 8-times oversampling digital filter Maximum input power: 40 W Impedance: 4 ohms Dimensions: Width; 160 mm (6-5/16") Height; 240 mm (9-1/2") Depth; 189 mm (7-1/16") Weight: 2.4 kg (5.3 lbs.)/each Frequency response: Wow and flutter: 20 - 20,000 Hz Unmeasurable (less than 0.001% W. peak) Specifications for this model are subject to change without prior notice. –3– XL-60H/70H NAMES OF PARTS XL-60H/70H 1 2 3 ■ Front panel 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. Timer Indicator Record Indicator Sleep Indicator (CD) Random Indicator (CD/TUNER) Memory Indicator RDS Indicator Traffic Programme Indicator Traffic Announcement Indicator FM Stereo Mode Indicator FM Stereo Indicator (CD) Play Indicator (CD) Repeat Indicator EON Indicator Programme Type Indicator Traffic Information Indicator Surround Indicator CD Compartment EON Button On/Stand-by Button Programme Type/Traffic Information Search Button Surround Button CD Open/Close Button ASPM Button Remote Control Sensor Display Mode Selector Button Volume Select Button 4 5 6 7 8 9 10 16 11 12 17 22 23 18 19 20 21 24 25 26 27 28 29 30 27. (CD/TAPE) Stop Button (TUNER) Memory Clear Button 28. Record Pause Button 29. Bass/Treble Selector Button 30. Memory/Set Button 31. Clock/Timer/Sleep Button 32. Band Selector Button 33. (CD) Review Button (TAPE) Rewind Button (TUNER) Tuning Down Button 34. Function Selector Button 35. Headphone Socket 36. (CD) Play/Pause Button (TAPE) Play Button 37. Jog Dial 38. (CD) Cue Button (TAPE) Fast Forward Button (TUNER) Tuning Up Button 39. Volume/Jog Dial Selector Button 40. Cassette Compartment 13 14 15 36 37 31 32 33 34 35 38 39 40 1 3 4 5 ■ Rear panel 1. 2. 3. 4. 5. CD Digital Output Socket AC Power Input Socket FM 75 ohms Aerial Socket AM Loop Aerial Input Socket Video/Auxiliary (Audio Signal) Input Sockets 6. Speaker Terminals 2 –4– 6 XL-60H/70H ■ Speaker section CP-XL60H 1. 2. 3. 4. Tweeter Woofer Bass Reflex Duct Speaker Wire 1 2 3 4 CP-XL70H 1. 2. 3. 4. 1 Tweeter Woofer Bass Reflex Duct Speaker Wire 2 3 4 XL-60H/70H ■ Remote control 1 1. Remote Control Transmitter LED ● Tuner control section 2. Programme Type/Traffic Information Search Button 3. Preset Up/Down Buttons 2 4 5 6 ● CD control section 4. Clear Button 5. Random/Repeat Button 6. Memory Button 7. Stop Button 8. Play/Pause Button 9. Track Down/Review Button 10. Track Up/Cue Button 11 12 ● Tape control section 11. Record Pause Button 12. Rewind Button 13. Stop Button 14. Play Button 15. Fast Forward Button 16 17 18 19 20 ● Common section 16. Surround Button 17. Sleep Button 18. Bass Up/Down Buttons 19. Function Selector Buttons 20. On/Stand-by Button 21. Timer Button 22. Clock Button 23. Treble Up/Down Buttons 24. Volume Up/Down Buttons –5– 3 7 8 9 10 13 14 15 21 22 23 24 15 15 Notes concerning use: ● Replace the batteries if the operating distance is reduced or if the operation becomes erratic. ● Periodically clean the transmitter LED on the remote control and the sensor on the main unit with a soft cloth. ● Exposing the sensor on the main unit to strong light may interfere with operation. Change the lighting or the direction of the unit. ● Keep the remote control away from moisture, excessive heat, shock, and vibrations. 1 3 3 –6– 2,3 AC INPUT Caution: ● The operation explained above will erase all data stored in memory, such as clock and timer settings, and tuner and CD presets. ton and the button, plug the AC power lead into the AC INPUT socket on this unit. 3 Whilst pressing down the MEMORY/SET but- socket on this unit. 2 Unplug the AC power lead from the AC INPUT stand-by mode. 1 Press the ON/STAND-BY button to enter the Reset the microcomputer under the following conditions: ● To erase all of the stored memory contents (clock and timer settings, and tuner and CD presets). ● If the display is not correct. ● If the operation is not correct. RESETTING THE MICROCOMPUTER 0.2m - 6m (8” - 20”) ■ Remote control PREPARATION FOR USE Jog dial 0:00 AM 12:00 ● When the jog dial is turned one click clockwise, the time will increase by 1 hour. When it is turned one click anti-clockwise, the time will decrease by 1 hour. Keep turning the jog dial to change the time continuously. ● When the 12-hour display is selected, “AM” will change automatically to “PM”. 5 Adjust the hour by turning the jog dial. 4 Press the MEMORY/SET button. The 24-hour display will appear. (0:00 - 23:59) “AM 12:00” → The 12-hour display will appear. (AM 12:00 - PM 11:59) ● Note that this can only be set when the unit is first installed or it has been reset (see page 29). “0:00” → 3 Turn the jog dial to select the time display mode. ton. 2 Within 3 seconds, press the MEMORY/SET but- ter the time check mode. 1 Press the CLOCK/TIMER/SLEEP button to en- CLOCK/TIMER/ SLEEP MEMORY/SET (Main unit operation) In this example, the clock is set for the 24-hour (0:00) system. SETTING THE CLOCK 2 Perform steps 1 - 8 above. THE MICROCOMPUTER”,. 1 Perform steps 1 - 3 in the section “RESETTING To change the time display mode: To change the clock time: Perform steps 1, 2 and 4 - 8 above. Note: ● In the event of a power failure or when the AC power lead is disconnected, the clock display will go out. When the AC power supply is restored, the clock display will flash on and off to indicate the time when the power failure occurred or when the AC power lead was disconnected. If this happens, follow the procedure below to change the clock time. ● The clock starts operating from “0” second. (Seconds are not displayed.) 8 Press the MEMORY/SET button. ● When the jog dial is turned one click clockwise, the time will increase by 1 minute. When it is turned one click anti-clockwise, the time will decrease by 1 minute. Keep turning the jog dial to change the time continuously. ● The hour setting will not advance even if minutes advance from “59” to “00”. 7 Adjust the minutes by turning the jog dial. 6 Press the MEMORY/SET button. XL-60H/70H OPERATION MANUAL XL-60H/70H 1 5 Check the supplied accessories Listening to a CD 3 OPEN/CLOSE 4 Label side up AM loop aerial ×1 Remote control × 1 5 1 (For U.K.) AC power lead × 1 FM aerial × 1 2 2 Insert the batteries. cover. 7 2 6 Putting batteries into the remote control 1 Remove the battery 6 (For Europe) 1 Press the ON/STAND-BY button to turn the power on. 2 Press the FUNCTION button until “CD” or “NO DISC” appears. 3 Press the OPEN/CLOSE button to open the CD compartment. 4 5 Place a CD on the spindle. 6 7 Press the 1 Press the ON/STAND-BY button to turn the power on. 2 Press the FUNCTION button until “TAPE” appears. 3 4 5 Load a cassette. cover. 4 5 2 ● 2 “AA” size batteries (UM/SUM-3, R6, HP-7 or similar) Placing the system 10 cm (4") 1 Press the ON/STAND-BY button to turn the power on. 2 Press the FUNCTION button until “FM” or “AM” appears. 3 Press the BAND button to select FM ST, FM or AM. 4 Press the TUNING ( tune into a station. button. Press the button. Adjust the VOLUME control. 3 10 cm (4") 7 20 cm (8") Listening to the radio 10 cm (4") 4 1 4 /CD Adjust the VOLUME control. Listening to a tape 3 Replace the battery 1 3 Close the CD compartment by pushing the OPEN/CLOSE button. 3 2 Connections 1 Connect the AM and FM aerials. 8 2 Connect the speaker system. 5 or ) button to 5 Adjust the VOLUME control. Recording from a CD 1 Press the ON/STAND-BY button to turn the power on. AM loop aerial FM aerial Right speaker 2 Press the FUNCTION button until 1 4 2 Left speaker 1 5 “CD” or “NO DISC” appears. 3 Load a CD and a recordable cassette. 4 Press the REC PAUSE button. 5 Press the button. 2 3 ● Resetting the micro computer 1 3 White line 2 1 If this product is subjected to strong external interference (mechanical shock, excessive static electricity, abnormal supply voltage due to lightning, etc.) or if it is operated incorrectly, it may malfunction or the display may not function correctly. If such a problem occurs, do the following: 3 1 2 3 3 AC INPUT 2,3 AC 230 V, 50 Hz (For U.K.) AC 230 V, 50 Hz (For Europe) Press the ON/STAND-BY button to enter the stand-by mode. Unplug the AC power lead from the AC INPUT socket on this unit. Whilst pressing down the MEMORY/SET button and the button, plug the AC power lead into the AC INPUT socket on this unit. Caution: ● The operation explained above will erase all data stored in memory, such as clock and timer settings, and tuner and CD presets. ● CD pickup cleaning ● Do not touch the laser pickup lens. If fingerprints or dust accumulate on the pickup, clean it gently with a dry cotton swab. 3 Connect the AC power lead. –7– XL-60H/70H DISASSEMBLY XL-60H/70H Caution on Disassembly Follow the below-mentioned notes when disassembling the unit and reassembling it, to keep it safe and ensure excellent performance: 1. Take cassette tape and compact disc out of the unit. 2. Be sure to remove the power supply plug from the wall outlet before starting to disassemble the unit. 3. Take off nylon bands or wire holders where they need to be removed when disassembling the unit. After servicing the unit, be sure to rearrange the leads where they were before disassembling. 4. Take sufficient care on static electricity of integrated circuits and other circuits when servicing. (A1)x1 ø3x10mm Top Cabinet CD PWB (B2)x1 (A1)x1 ø3x10mm Main PWB (B1)x1 ø3x10mm Display PWB Front Panel (B2)x1 (C1)x2 ø3x10mm XL-60H/70H STEP REMOVAL PROCEDURE FIGURE 1 Side Panel(Left/Right) 1. Screw .................. (A1) x8 8-1 2 Top Cabinet 1. Screw .................. (B1) x1 2. Socket ................. (B2) x2 8-1 3 Rear Panel 1. Screw .................. (C1) x3 2. Screw .................. (C2) x2 8-1 4 Power Amp. PWB 1. Screw .................. (D1) x1 2. Socket ................. (D2) x2 8-2 5 Main PWB/ Headphones PWB 1. Screw .................. (E1) x3 2. Screw .................. (E2) x2 3. Bracket ................ (E3) x1 4. Socket ................. (E4) x3 5. Flat wire ............... (E5) x1 6. Socket ................. (E6) x1 8-3 6 Jog Switch PWB 1. Socket ................. (F1) x1 2. Screw .................. (F2) x2 3. Knob .................... (F3) x1 8-3 7 Display PWB/ LED PWB (With Jog Motor Holder) 1. Screw .................. (G1) x3 2. Screw .................. (G2) x3 3. Bracket ................ (G3) x1 4. Socket ................. (G4) x1 5. Hook .................... (G5) x2 6. Hook .................... (G6) x2 8-3 1. Screw .................. (H1) x1 2. Socket ................. (H2) x1 3. Screw .................. (H3) x1 8-3 1. Screw .................. (J1) x4 2. Screw .................. (J2) x1 3. Screw .................. (J3) x1 4. Bracket ................ (J4) x1 8-3 8 9 Front Panel Power PWB Power PWB (E6)x1 (E4)x1 (G5)x2 (E2)x1 ø3x8mm (G6)x2 LED PWB Headphones PWB (G3)x1 Display PWB 11 CD PWB/ 1. Screw .................. (L1) x6 Open Close Switch 2. Socket ................. (L2) x4 PWB/CD Lid PWB 3. Hook .................... (L3) x1 (Note) 9-2 Digital Out PWB 9-2 1. Screw .................. (N1) x3 2. Screw .................. (N2) x3 (D2)x2 Power Amp. PWB (F3)x1 9-1 CD Mechanism Main PWB (F1)x1 1. Open the cassette holder 2. Screw .................. (K1) x4 13 (D1)x1 ø3x8mm (G2)x2 ø2.5x10mm Tape Mechanism 1. Socket ................. (M1) x1 2. Screw .................. (M2) x1 (A1)x2 RearPanel ø3x10mm Side Panel (Right) Figure 8-1 Side Panel (Lift) (C1)x1 ø3x10mm Figure 8-2 10 12 (A1)x4 ø3x10mm (C2)x2 ø3x8mm 9-3 (E4)x1 Front Panel Jog Switch PWB (E5)x1 (H2)x1 (E1)x2 ø3x10mm Main PWB (G2)x1 ø2.5x10mm (F2)x2 ø2.5x12mm Jog Motor Tape Holder Mechanism PWB (E3)x1 (E1)x1 ø3x10mm (G4)x1 (H3)x1 ø3x6mm Note: After removing the connector for the optical pickup from the connector, wrap the conductive aluminium foil around the front end of connector remove to protect the optical pickup from electrostatic damage. (G1)x3 ø2.5x14mm (E4)x1 Power PWB (J3)x1 ø3x6mm (J2)x1 ø3x10mm (H1)x1 ø3x8mm (E2)x1 ø3x8mm (J1)x4 ø4x6mm Power PWB (J4)x1 Sub Power Transformer Main Power Transformer Sub Power Transformer Figure 8-3 –8– XL-60H/70H CP-XL60H Front Panel STEP 1 PROCEDURE FIGURE 1. Net Frame ........... (A1) x1 2. Front panel .......... (A2) x1 3. Screw .................. (A3) x4 9-4 REMOVAL Speaker Tape Mechanism Open Speaker Box Tweeter Cassette Holder (K1)x4 ø2.5x10mm (A2)x1 (A1)x1 Figure 9-1 (L1)x3 ø2.5x14mm CD PWB (M2)x1 ø2.5x10mm Digital Out PWB PWB Washer (A3)x4 ø4x20mm Woofer (L2)x2 (L1)x2 (M1)x1 ø2.5x8mm (L2)x1 Figure 9-4 (L1)x1 ø2.5x10mm (L2)x1 CP-XL70H CD Lid PWB (L3)x1 STEP 1 Open/Close Switch PWB CD Motor PWB PROCEDURE FIGURE 1. Net Frame ........... (A1) x1 2. Screw .................. (A2) x4 2. Woofer Ring ........ (A3) x1 4. Screw .................. (A4) x4 9-5 REMOVAL Speaker Top Cabinet CD Mechanism Tweeter Figure 9-2 (A1)x1 (N1)x3 ø2.5x14mm CD Lid Motor (N2)x3 ø2.5x10mm (A4)x4 ø3x12mm PWB Washer x3 CD Lid Motor Holder (A3)x1 (A2)x4 ø4x20mm Top Cabinet CD Mechanism Figure 9-5 Figure 9-3 –9– Speaker Box Woofer XL-60H/70H REMOVING AND REINSTALLING THE MAIN PARTS TAPE MECHANISM SECTION (A2)x1 ø2x7mm Perform steps 1 to 8 and 10 of the disassembly method to remove the tape mechanism. (See page 8.) (A2)x1 ø2x3mm (A1)x2 ø2x8mm How to remove the record / playback and erase heads (See Fig. 10-1.) 1. Remove the screws (A1) x 2 pcs., to remove the erase head. 2. Remove the screws (A2) x 2 pcs., to remove the record/ playback head. Note: After replacing the heads and performing the azimuth adjustment, be sure to apply screwlock. Erase Head Record/ Playback Head Figure 10-1 How to remove the pinch roller (See Fig. 10-2.) 1. Carefully bend the pinch roller pawl in the direction of the arrow <A>, and remove the pinch roller (B1) x 1 pc., upwards. <A> Pinch Roller Pawl Pinch Roller (B1)x1 Figure 10-2 How to remove the belts (See Fig. 10-3.) 1. Remove the main belt (C1) x 1 pc., from the motor pulley. 2. Remove the FF/REW belt (C2) x 1 pc., from the REW/FF roller. 3. Put on the belts in the reverse order of removal. Note: When putting on the belt, ascertain that the belt is not twisted, and clean it. Motor Main Belt (C1)x1 REW/FF Clutch FF/REW Belt (C2)x1 Figure 10-3 How to remove the motor (See Figs. 10-4.) (D2)x3 Special Screw (D1)x1 ø2x4mm Motor 1. Remove the mainbelt. 2. Remove the screws (D1) x 2 pcs., to remove the motor bracket. 3. Remove the screws (D2) x 3 pcs., to remove the motor. Note: When mounting the motor, pay attention to the motor mounting angle Motor Bracket (D1)x1 ø2x4mm Motor Figure 10-4 How to remove the flywheel (See Fig. 10-5.) 1. Remove the belt. 2. Remove the stop washer (E1) x 1 pc., with a small precision screwdriver to extract the flywheel from the capstan metal. Note: When the stop washer is deformed or damaged, replace it with a new one. Mechanism Chassis (E1)x1 Stop Washer Stop Washer Washerx2 Flywheel How to reinstall the parts Install each part in the reverse order of the removal with care. Figure 10-5 – 10 – Driver XL-60H/70H How to remove the tape mechanism PWB (See Fig. 11-1.) (F1)x1 Tape ø2x3mm Mechanism PWB 1. Remove the screws (F1) x 1 pc., to remove the tape mechanism PWB. 2. Remove the screws (F2) x 1 pc. 3. Remove the solder joints (F3) x 2 pcs., to remove the tape mechanism PWB. (F2)x1 ø2x8mm Tape Mechanism PWB (F3)x2 Solder Joint Figure 11-1 How to remove the jog motor (See Figs. 11-2.) Jog Motor 1. Remove the side panel and top cabinet. 2. Remove the jog belt (G1) x 1 pc., from the motor pulley. 3. Remove the screws (G2) x 2 pcs., to remove the jog motor. Note: When putting on the belt, ascertain that the belt is not twisted, and clean it. (G2)x2 ø2x5mm Display PWB Worm Gear Jog Belt Jog Motor Holder (G1)x1 Figure 11-2 How to remove the CD lid motor (See Figs. 11-3.) (H1)x1 Belt Worm Gear 1. Remove the CD PWB. 2. Remove the belt (H1) x 1 pc., from the motor pulley. 3. Remove the screws (H2) x 2 pcs., to remove the CD Lid motor. Note: When putting on the belt, ascertain that the belt is not twisted, and clean it. CD Lid Motor (H2)x2 ø2.5x10mm Figure 11-3 Mechanism Cover CD MECHANISM SECTION (A1) x2 Perform steps 1, 2 and 10 to 12 of the disassembly method to remove the CD mechanism. (A1) x2 (A2) x2 ø2.6 x6mm How to remove the pickup (See Fig. 11-4) 1. Remove the mechanism cover, paying attention to the pawls (A1) x 4 pcs. 2. Remove the screws (A2) x 2 pcs., to remove the shaft (A3) x 1 pc. 3. Remove the stop washer (A4) x 1 pc., to remove the gear (A5) x 1 pc. 4. Remove the pickup. CD Mechanism Shaft (A3) x1 Note: After removing the connector for the optical pickup from the connector, wrap the conductive aluminium foil around the front end of connector remove to protect the optical pickup from electrostatic damage. StopWasher (A4) x1 Gear (A5) x1 Pickup Unit Figure 11-4 – 11 – XL-60H/70H ADJUSTMENT MECHANISM SECTION TUNER SECTION • Driving Force Check fL: Low-range frequency fH: High-range frequency • AM IF/RF Signal generator: 400 Hz, 30%, AM modulated Torque Meter Specified Value Play: TW-2412 Over 80 g Torque Meter Specified Value Play: TW-2111 30 to 60 g. cm Fast forward: TW-2231 55 to 140 g.cm Rewind: TW-2231 55 to 140 g.cm • Tape Speed Adjusting Point Test Tape MTT-111 Display Frequency Frequency • Torque Check Variable resistor in motor.(M901) Specified Value 3,000 ± 90 Hz Instrument Connection Headphone terminal Setting/ Instrument Adjusting Connection Parts T351 *1 AM IF 450 kHz 1,620 kHz AM Band Coverage — 522 kHz (fL): T306 *2 1.1 ± 0.1 V AM Tracking 990 kHz 990 kHz (fL): T302 *1 *1. Input: Antenna, Output: Speaker Terminal *2. Input: Input is not connected, Output: TP301 • Setting the Test Mode Keeping the FF/FWD button and MEMORY/SET button pressed, turn on POWER. Then, the frequency is initially set in the memory as shown in Table. Call it with the JOG DIAL knob to use it for adjustment and check of tuner circuit. TAPE MECHANISM Preset No. 1 2 3 4 5 M901 Tape Motor FM 87.50 MHz 108.00 MHz 98.00 MHz 90.00 MHz 106.00 MHz AM Preset No. 6 7 8 9 10 522 kHz 1,620 kHz 990 kHz 603 kHz 1,404 kHz • FM Mute Level Signal generator: 1 kHz, 40 kHz dev., FM modulated Variable resistor in motor Frequency 98.00 MHz (30 dBµV) Figure 12-1 ADJUSTMENT POINT Display 98.00 MHz Adjusting Parts VR351*1 Instrument Connection Input: SO301 Output: Speaker Terminal *1. Adjust so that an output signal appears. • Check FM VT Signal generator: 1 kHz, 40 kHz dev., FM modulated Frequency MAIN PWB AM IF VR351 FM Mute Level FE301 T351 TP301 AM Band Coverage fL T302 AM Tracking fL 87.5 MHz 2.2 V ± 0.7 V TP301 108 MHz 7.3 V ± 1.0 V TP301 CNP301 AM ANTENNA SOCKET – 12 – Instrument Connection 108 MHz SO301 FM ANTENNA SOCKET Figure 12-2 ADJUSTMENT POINTS Check Point 87.5 MHz R336 T306 Display XL-60H/70H RDS CIN Subcarrier input (comparator input). 7 TEST Test input. 8 XOUT Crystal oscillator output (4.332MHz). XIN Crystal oscillator input (external reference signal input). 10 Vssd Digital ground. 11* Vddd Digital power supply (+5V). 12 MODE Read mode setting (0 : master, 1: slave). 13 RST RDS-ID/RAM reset (positive polarity). 14 RDDA RDS data output. 15* RDCL RDS clock output (master mode)/ RDS clock input (slave mode). 16* RDS-ID/ READY RDS-ID/READY output (negative polarity). 6 5 13 RST 12 MODE 57kHz BPF (SCF) FLOUT Descriptions of the PTY (Programme Type) codes, TP (Traffic Programme) and TA (Traffic Announcement) With the XL-60H/XL-70H, you can search for and receive the following PTY, TP and TA signals. LIGHT M: NEWS: Short accounts of facts, events and publicly expressed views, reportage and actuality. CLASSICS: Performances of major orchestral works, symphonies, chamber music, etc., and including Grand Opera. AFFAIRS: Topical programme expanding or enlarging upon the news, generally in different presentation style or concept, including debate, or analysis. OTHER M: INFO: Programmes whose purpose is to impart advice in the widest sense. Note: When the TP and TA appear at the same time, an announcement is being made. When only the TA appears, an announcement is not being made. SPORT: Programme concerned with any aspect of sport. ■ Information Provided by RDS DRAMA: PS (Programme Service): Station names commonly known will be displayed. "NO PS" appears if no signal is being received. PTY (Programme Type): Programme type will be displayed. "NO PTY" appears if no signal is being received. EDUCATE: Programme intended primarily to educate, of which the formal element is fundamental. VARIED: Used for mainly speech-based programmes usually of light-entertainment nature, not covered by other categories. Examples include: quizzes, panel games, personality interviews. Commercial music, which would generally be considered to be of current popular appeal, often featuring in current or recent record sales charts. ROCK M: Contemporary modern music, usually written and performed by young musicians. EASY M: Current contemporary music considered to be “easy-listening”, as opposed to Pop, Rock or Classical, or one of the specialised music styles, Jazz, Folk or Country. Music in this category is often but not always, vocal, and usually of short duration. Classical Musical for general, rather than specialist appreciation. Examples of music in this category are instrumental music, and vocal or choral works. FINANCE: Stock Market reports, commerce, trading, etc. CHILDREN: For programmes targeted at a young audience, primarily for entertainment and interest, rather than where the objective is to educate. SOCIAL: Programmes about people and things that influence them individually or in groups. Includes: sociology, history, geography, psychology and society. RELIGION: Any aspect of beliefs and faiths, involving a God or Gods, the nature of existence and ethics. PHONE IN: Involving members of the public expressing their views either by phone or at a public forum. TRAVEL: Features and programmes concerned with travel to near and far destinations, package tours and travel ideas and opportunities. Not for use for announcements about problems, delays, or road-works affecting immediate travel where TP/TA should be used. LEISURE: Programmes concerned with recreational activities in which the listener might participate. Examples include, Gardening, Fishing, Antique collecting, Cooking, Food & Wine, etc. JAZZ: Polyphonic, syncopated music characterised by improvisation. COUNTRY: Songs which originate from, or continue the musical tradition of the American Southern States. Characterised by a straightforward melody and narrative story line. – 13 – TEST TEST 7 MPXIN NATION M: Current Popular Music of the Nation or Region in that country’s language, as opposed to international ‘Pop’ which is usually US or UK inspired and in English. OLDIES: Music from the so-called “golden age” of popular music. FOLK M: Music which has its roots in the musical culture of a particular nation, usually played on acoustic instruments. The narrative or story may be based on historical events or the people. Musical styles not fitting into any of the other categories. Particularly used for specialist music of which Rhythm & Blues and Reggae are examples. WEATHER: Weather reports and forecasts and meteorological information. Programmes about the natural sciences and technology. POP M: Station frequencies. DISPLAY MODE All radio plays and serials. CULTURE: Programmes concerned with any aspect of national or regional culture, including language, theatre, etc. SCIENCE: 2 REFERENCE VOLTAGE Vssa 4 3 (Continued) RDS (Radio Data System) OPERATION RDS is a broadcasting service which a growing number of FM stations are now providing. It allows these FM stations to send additional signals along with their regular programme signals. For example, the stations send their station names, and information about what type of programme they broadcast, such as sports or music, etc. When tuned to an FM station providing the RDS service, RDS will appear, the station frequency (and then the station name if sent) will be displayed. The TP (Traffic Programme) will appear on the display when the received broadcast carries traffic announcements, and the TA (Traffic Announcement) will appear whilst a traffic announcement is being received. EON will appear whilst the EON (Enhanced Other Networks information) data is being broadcast. With the XL-60H/XL-70H, you can display two types of RDS service. To show them in the display, press the DISPLAY MODE button. Each time you press the DISPLAY MODE button, the display will change to show the following information. ANTIALISING FILTER 1 Vdda In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. Station Frequency: 15 RDCL 14 RDDA 10 CIN 9 XOUT 6 8 Subcarrier output (filter output). 9 FLOUT XIN 5 16 RDS-ID/ READY Analog ground. RDS-ID DETECT Vssa OSC Analog power supply (+5V). 4 CLK(4.332MHz) Baseband (multiplexed) signal input. Vdda RAM (128-bits) MPXIN 3 DATA DECODER 2 SMOOTHING FILTER Reference voltage output (Vdda/2). VREF VREF PLL (57kHz) 1 CLOCK RECOVERY (1187.5Hz) Function Vssd Vddd Port Name VREF Pin No. 11 IC521 VHiLC72723M-1: RDS Circuit (LC72723M) DOCUMENT: Programme concerned with factual matters, presented in an investigative style. TEST: Broadcast when testing emergency broadcast equipment or receivers. ALARM: Emergency announcement made under exceptional circumstances to give warning of events causing danger of a general nature. NONE: No programme type (receive only). TP: Broadcasts which carry traffic announcements. TA: Traffic announcements are being broadcast at present. Note: ● When the unit is in the EON stand-by mode and a programme is selected, the unit will display “TI” instead of “TP” or “TA”. XL-60H/70H TEST MODE The test mode applied to this microcomputer has three modes, namely ordinary test mode to be used for adjustment or measurement, aging test mode to be used for aging test, and self-diagnosis test mode for self-inspection in case of final product inspection. The test mode specification prescribes the microcomputer with RDS (RH-IX0026SJZZ) . There are two types of indication examples; large ones for the microcomputer with RDS, and smaller ones for the microcomputer without RDS. 1. Turning on the test mode To turn on the specific test mode, press the POWER button, holding down the following two buttons in the ordinary stand-by mode (power off state). In this case only the main unit button is valid. Even when the POWER of remote control button is set to on, the test mode is not turned on. [Ordinary test mode] 1. CD Test Mode (TEST 1)…………………… Volume/JOG Dial Selector + FF/FWD 2. Tuner Test Mode (TEST 2)………………… Volume/JOG Dial Selector + Volume Select 3. Electronic volume Test Mode (TEST 3)…… REW/REV + FF/FWD 4. Timer Test Mode (TEST 4)………………… FUNCTION + Volume Select 5. LCD Test Mode (TEST 5)……………………FUNCTION + FF/FWD [Self-diagnosis Test Mode] 1. Button input diagnosis test mode (TEST6).… REW/REV + Volume Select 2. CD Test Mode (TEST 1) In the CD test mode the operation of each step is enabled even when the LID-SW is off. However, if focus cannot be set in step 3 or any error processing is started, it is impossible to proceed to the next step. When the error processing is started, operations other than termination of test mode by pressing the POWER button or return to the step 1 by pressing the STOP button are inhibited. 1. Step 1 Mode When the CD test mode is turned on, the following indication lights, the processing (until turning-off of CD STB terminal of CD initialization operation flow) is executed, and the next button input is waited. After lighting for one second If the following operation buttons are pressed in this state, the operation is performed as follows. "POWER" ................. The test mode is turned off, the power is turned off, and the ordinary standby mode is set. "FF/FWD" ................. After the pickup returns once to the innermost periphery, it slides toward the outer periphery while this button is held down. "REW/REV" .............. After the pickup returns once to the innermost periphery, it slides toward the inner periphery while this button is pressed. However, if PU-IN is on, input is invalid. "PLAY" ..................... Shift to step 2 "STOP" ..................... Invalid "REC PAUSE" .......... Shift to step 5 * In case of initialization the pickup is moved toward the inner periphery. Any buttons other than "POWER" button are not accepted until the shift of pickup to the inner periphery is completed at this time. If PU-IN SW ON cannot be detected within 10 seconds, the slide motor is stopped, and the following error indication appears. Press the POWER button to end the test mode, or press the STOP button to return to step 1. Any other operations are inhibited. – 14 – XL-60H/70H 2. Step 2 Mode When the "PLAY" button is pressed in this mode, the laser lighting command LDON (8400) is sent, and the laser is turned on. Other operations are not performed. If the following buttons are pressed in this state, the operation is performed as follows. "POWER" ................ The test mode is turned off, the power is turned off, and the ordinary standby mode is set. "FF/FWD" ................ The pickup slides toward the outer periphery while this button is held down. "REW/REV" ............. The pickup slides toward the inner periphery while this button is held down. However, if PU-IN is on, input is invalid. "PLAY" ..................... Shift to step 3 "STOP" .................... Return to step 1 "REC PAUSE" ......... Shift to step 5 3. Step 3 Mode The laser is kept lighting. The processing (until turning-on of CLV servo of CD initialization operation flow) is executed, and the next button input is waited. (The focus servo is turned on, and focus search is performed.) The focus search is repeated until the focus is set. When the following operation buttons are pressed in this state, the operation is executed as follows. "POWER" ................ The test mode is turned off, the power is turned off, and the ordinary standby mode is set. "FF/FWD" ................ The pickup slides toward the outer periphery while this button is held down. "REW/REV" ............. The pickup slides toward the inner periphery while this button is held down. However, if PU-IN is on, input is invalid. "PLAY" ..................... If the focus has been set, shift to step 4 is executed. If the focus has not been set, acceptance is inhibited. "STOP" .................... Return to step 1 "REC PAUSE" ......... Shift to step 5 *If the focus is disturbed after it has been set, the process returns to step 1. 4. Step 4 Mode The CLV servo ON command (8600) sending operation is performed, and the next button input is waited. (The disc is rotated to perform CLV locking.) The time display indicates always "0:00". When the following buttons are pressed in this state, the operation is executed as follows. "POWER" ................ The test mode is turned off, the power is turned off, and the ordinary standby mode is set. "FF/FWD" ................ The pickup slides toward the outer periphery while this button is held down. "REW/REV" ............. The pickup slides toward the inner periphery while this button is held down. However, if PU-IN is on, input is invalid. "PLAY" ..................... Shift to step 5 "STOP" .................... Return to step 1 "REC PAUSE" ......... Shift to step 5 *If the focus is disturbed, the process returns to step 1. – 15 – XL-60H/70H 5. Step 5 Mode The CD initialization operation flow is executed to the end, the mute is set to off, and playback is started. Even when the playback reaches the outermost periphery of disc, the operation does not stop. The LCD display indicates the playback past time as in case of ordinary CD playback. When the following operation buttons are pressed in this sate, the operation is executed as follows. "POWER" ................. The test mode is turned off, the power is turned off, and the ordinary standby mode is set. "FF/FWD" ................. The pickup slides toward the outer periphery while this button is held down. "REW/REV" .............. The pickup slides toward the inner periphery while this button is held down. However, if PU-IN is on, input is invalid. "PLAY" ..................... Invalid "STOP" ..................... Return to step 1 *If the focus is disturbed, the process returns to step 1. Other cautions • TOC IL is not executed in the test mode. • As for button operations other than those shown above, only the sound volume operation (with JOG) is accepted. 3. Tuner Test Mode (TEST 2) 1. Outline of tuner (radio) test mode The tuner test mode is intended to store the adjustment and measurement frequencies in the preset memory CH without frequency setting by adjusting personnel when the tuner section is adjusted in the production line. 2. Details of tuner test mode When the power is turned on by using the "POWER" button while the "Volume/JOG Dial Selector" and "Volume Select" buttons are held down in POWER OFF state, the frequency for adjustment and measurement of destination specified by the AREA terminal is preset and stored in the preset memory CH. However, Ordinary 1 and Ordinary 2 are set to the designation (destination selected by SPAN switching operation) set when the test mode is set. (As for frequencies to be preset and stored for each destination, refer to item 3.) The tuner test mode is started from preset No.1. The operations of test mode are identical with the ordinary operations of TUNER function. However, FUNCTION switching is invalid. Since it is necessary to discard the content of preset memory when the tuner test mode is ended, "0000" or "1111" bits are written in the memory to be checked in case of memory check (in case of initial setting) so that memory abnormality is detected in case of initial setting so as to ensure memory initialization. When the tuner test mode is turned on, the following indication lights for one second. • The TUNER TEST2 mode is set as a result of Volume Select + POWER. -> IF AC is set to OFF in the TEST2 mode, the initial state is restored. When POWER is set to OFF, the memory of TEST2 mode is protected. When the power is turned on again, the ordinary operation is enabled while the data is stored in the memory (besides TUNER). If AC OFF state is maintained in this state for about 1/2 day, start is executed in the initial state. • To clear the whole memory, insert the AC cord, holding down MEMORY + PLAY. – 16 – XL-60H/70H 3. Preset frequencies for various destinations (random preset memory) CH 1 2 3 4 5 BAND FM STEREO Europe 2, 4 CH 6 7 8 9 10 11-15 FM 87.50 MHz FM108.00 MHz FM 98.00 MHz FM 90.00 MHz FM106.00 MHz BAND AM Europe 2, 4 AM 522 kHz AM1620 kHz AM 990 kHz AM 603 kHz AM1404 kHz LW CH 16-25 26 27 28 29 30 BAND FM MONO Europe 2, 4 FM106.00 MHz FM 90.00 MHz FM 98.00 MHz FM108.00 MHz FM 87.50 MHz • The hatched sections of the table are not stored in memory. 4. ASPM TEST Mode When the ASPM button is pressed, the test mode is set. It starts up at FM 106.50 MHz. (ST mode) Data of 27 CH of 04 to 30 CH are all stored at FM 87.50 MHz (ST). 01 to 03CH are kept empty (If data of 3 CH are stored, max. 30 CH is filled.) When the ASPM button is operated in the TEST mode 3, the preset data is cleared (overwrite). A) Operation with ASPM button Press the "ASPM" button or hold it down. (Any button other than ASPM button cancels the ASPM test mode.) FM 105.00 MHz (ST) is indicated, and scan is started. (Start from 105.00 MHz) When the ASPM button is pressed once in the TUNER TEST mode, the indication FM 106.50 MHz (ST) appears, and data of 04 to 30 CH are stored at 87.50 MHz (ST). When the ASPM button is operated again, the ASPM test operation mode is set. During scanning the frequency is indicated. End at FM 108.00 MHz (ST) Only the number of preset and stored stations (number of CHs: max. 3 stations) is indicated for one second in the ASPM test mode. When two stations are stored, "_2 MEMORY" is indicated (lighted)for one second. ("02 MEMORY" indication is not given.) In case of "_0 MEMORY" the process ends, and the FM 106.50 MHz (ST) state is resumed. "END" is not indicated 01CH indication (for one second) Not in zero-memory state (An example) FM P-01 Frequency indication (for one second) FM 105.50MHz(ST) 02CH indication (for one second) FM P-02 Frequency indication (for one second) FM 106.50MHz(ST) 03CH indication (for one second) FM P-03 Frequency indication (for one second) FM 107.50MHz(ST) Confirmation of content of memory (Examples of concrete indication) After indication of continuous time series for one second the indication of FM 106.50 MHz (ST) is restored. (The preset button is not pressed. The time series is indicated automatically, and the content of memory is indicated.) * PS name is not indicated (while the content of memory is checked) * If only 1 CH data is stored, FM P-01 -> FM 106.00 MHz -> FM 106.50 MHz (ST) (An example) (1 sec) (1 sec) (ST) End indication – 17 – XL-60H/70H * When the "PRESET UP" button or "PRESET DOWN" button is pressed after completion, the following indication appears. CH indication (for 2 seconds) Frequency indication (for 2 seconds) Time series indication of PS name indication is enabled. (The same as in case of Ordinary) NO PS (Blinking for 5 seconds: 1 Hz) Note: If PS is fixed after the frequency indication is resumed, the PS name indication is restored. * If signal exists at 106.50 MHz, the following indication appears. FM 106.50 MHz PS name When the PS data is given in case of NO PS indication, the PS name indication is restored. NO PS (Blinking for 5 seconds: 1 Hz) Note: If PS is fixed after the frequency indication is resumed, the PS name indication is restored. In case of memory storage with ASPM, for example, if RDS station 107.50 MHz has the PI code (the same as that of RDS station 105.50 MHz) and VSM is greater than 105.50 MHz (PR-01), data is overwritten on 105.5 MHz which is contained in "PR-01". (Frequency is changed to 107.50 MHz.) If VSM is equal, previously stored 105.50 MHz remains. When RDS station is stored in the test mode, the 2-second blinking of preset No. is not performed so as to save the production line test time. ("RDS" lighting is performed.) Note: RDS operation is performed in FM MONO state. However, in case of ASPM, ASPM scan is performed after BAND is changed from FM MONO to FM STEREO. Note: When the (PLAY) button is pressed in TEST 2 mode, it is possible to check the sate of IF count. However, this function is for designer. It is not necessary for other sections. B) Cautions concerning the ASPM test mode a) Cancel: When the "ASPM" button is pressed again during operation after it was first pressed in the test mode, the ASPM test mode is canceled (interrupted), and the initial state FM 106.50 MHz (ST) indication is restored. (To check the data which was preset and stored until interruption, use the preset UP/DOWN button. (JOG UP/DOWN is also available after JOG mode button operation.) wing indication appears. b) The ASPM test mode is started in FM stereo state (FM 106.50 MHz ST). If any button other than ASPM button is pressed even only once after it is started, it becomes invalid, and the ASPM test mode becomes inoperable. Invalid: The Ordinary mode is set while 4 to 30CH data remain in memory (or 1 to 30 CH MAX data remain in memory). The "ASPM" button can be repeatedly operated until 01CH to 03CH is filled (up to 3 stations in memory). The number of stored stations -> Channel No. -> Frequency -> FM 106.50 MHz (ST) is indicated. (1 second) (1 second) (1 second) (Initial state) Up to 3 stations (1 to 3CH) can be indicated. This indication is given only in the ASPM test mode. In other mode (not in ASPM test mode) the number of stored stations -> END is indicated c) Broadcast (without PI code) which is not RDS is not preset and stored in memory. When the ASPM mode is set, the "MEMORY/SET" button cannot be operated (the test mode is canceled). Operation is possible after ASPM test mode operation. d) Scan frequency: 105.00 MHz -> 108.00 MHz Data are stored in memory so that the PI code is not duplicated (by seeing the PI code and VSM (S meter value). When the PI code is duplicated, both VSM (S meter value) are compared. The greater one is stored in memory but the smaller one is discarded. For the stations having the same PI code, only one station having the highest electric field intensity is stored, and the memory is refilled. The channels which can be preset in the ASPM test mode are 01 to 03CH. If 3 stations are stored, 30 CH are filled. For the stations having the same electric field intensity, the former (preceding station) is stored. e) Signal of already stored same frequency is not stored. (The previously stored data is kept.) f) The order of preset memory is 01CH -> 02CH -> 03CH. – 18 – XL-60H/70H g) When 01 to 03CH were all used, scan is aborted at the frequency at which filling occurred, and the following indication appears. Number of stored stations -> Indication of stored channel -> Indication of frequency -> Return to initial FM 106.50 MHz (ST) (1 second) (1 second) (1 second) In this period up to 3 stations are continuously indicated (1 to 3 CH). h) If even one station could not be preset and stored in the APMS mode, "_0MEMORY" is indicated after scanning, and then FM 106.50 MHz (ST) indication is restored. (The first digit is space.) ("_0MEMORY" is indicated in the test mode.) i) When the "ASPM" button is pressed after three stations are stored (after full-memory of 30 stations), "ASPM" blinks for 2 seconds, and then FM 106.50 MHz (ST) indication is restored without ASPM scanning. (RDS automatic lighting) (In case of ASPM button operation in full memory state) j) After completion of specific operation FM 106.50 MHz (ST) indication is restored. k) Test mode Use of only the function button is inhibited. l) The first channel to be called (when data is stored in the ASPM mode) is 01CH. m) After start-up in the ASPM test mode the ASPM key is valid even when it is pressed many times. The test mode is kept. If three stations are stored (1 to 3CH), full-memory state occurs. If the ASPM button is pressed after occurrence of full-memory state, the same operation as that described in item i) is performed. 4. Electronic volume Test Mode (TEST 3) When the test mode is set, the following indication lights for one second. When this mode is set, BASS/TREBLE is set to 0 (0 dB) and SURROUND mode is set to off, and start-up function is set to CD when volume is -14 dB (STEP 17). The button operations in the test mode are the same as those of ordinary operation excepting sound volume UP/DOWN. (1) The indication is the same as that of ordinary operation excepting test mode setting. (2) The sound volume control with the sound volume UP/DOWN button is only the following 3 steps unlike the ordinary state. Volume- ∞ (STEP 0) <-> Volume-14 dB (STEP 23) <-> Volume-0 (STEP 30) (3) BASS/TREBLE and SURROUND are switched when button operation is performed. 5. Timer test Mode (TEST 4) When the test mode is set, the following indication lights for one second. The current time and timer time are set in the following procedure to perform the timer playback. 1.Set the current time to 1:00, set the timer to ON time 1:02, set the function to Tape, and set volume STEP 8. One minute is counted as one second, and the timer playback operation is performed. The fade-in (when playback is started) is executed at a rate of one step for 0.5 sec. After completion of fade-in the fade-out is executed at a rate of one step for 0.5 sec (WAIT 1 sec inserted). After completion of fade-out the power is turned off (after WAIT 1 sec), and the mode is changed to the standby mode. The indication during operation is the same as that of ordinary timer operation. 6. LCD Test Mode (TEST 5) When the LCD test mode is set, all the LCD segments are lighted. After that the indication is changed as follows according to the "PLAY" button input. Lighting of all segments Lighting of odd segments – 19 – Lighting of even segments XL-60H/70H 7. Key input diagnosis Test Mode (TEST 6) When the test mode is set, the following indication appears. This test mode is intended to check whether all the main unit buttons can be detected. Accordingly, in this test mode checking as to whether the "POWER" button was pressed after all the buttons shown below were pressed is performed. If the result is OK, OK is indicated. Even any one of keys was not pressed, an error is indicated. In case of OK termination or error termination exit from this mode occurs when the "POWER" button is pressed next time, and the standby mode is set. 1. In case of "FUNCTION" + "RDS PTY-TP" Since SURROUND and RDS are provided, the following 16 buttons are detected as all buttons. PLAY, JOG MODE, BAND, BASS/TREBLE, FUNCTION, MEMORY/SET, REC PAUSE, REW, FF, STOP, CLOCK/TIMER/ SLEEP, PTY-TI, EON, APMS, DISPLAY, SURROUND The OK/NG indication of test result is as follows. ERROR LIST PU-IN SW detection error Tape mechanism error 1 Error content ............ The detection SW cannot detect ON after a fixed period of time even if the microcomputer controls the CD pickup to return to the innermost position. Probable cause ........ Defective or poorly connected PU-IN SW or slide motor. Action ....................... Solve the problem and turn on the power again. Error content ........... The detection SW "CAM-SW" cannot detect ON (mechanism in operation) even if the motor and solenoid are controlled to play back, fast forward, rewind, or record the tape. Probable cause ....... Mechanism is in operation when this message appears: Defective or poorly connected CAM-SW. Mechanism stops: Defective or poorly connected motor or solenoid. Action ...................... Solve the problem and turn on the power again. CD read error Error content ........... Disc data cannot be read properly or even if it can be read, the disc is not a playable one. Probable cause ....... The disc is loaded upside down, not CDDA, scratches, stains, etc. Action ...................... Open the CD lid, then reload the disc correctly. Remove the scratches or stains on the disc. NO DISC Error content ........... Focusing is impossible. Probable cause ....... The disc is loaded upside down, not CDDA, scratches, stains, etc. Action ...................... Open the CD lid, then reload the disc correctly. Remove the scratches or stains on the disc. Tape mechanism error 2 Error content ........... Initialization cannot be completed when the microcomputer controls the motor and solenoid to initialize the tape mechanism (to set the mechanism to the stop mode). The detection SW "CAMSW" cannot detect OFF While the mechanism is in operation. Probable cause ....... Mechanism is in operation when this message appears: Defective or poorly connected CAM-SW. Mechanism stops: Defective or poorly connected motor or solenoid. Action ...................... Solve the problem and turn on the power again. – 20 – XL-60H/70H NOTES ON SCHEMATIC DIAGRAM • Resistor: To differentiate the units of resistors, such symbol as K and M are used: the symbol K means 1000 ohm and the symbol M means 1000 kohm and the resistor without any symbol is ohm-type resistor. Besides, the one with “Fusible” is a fuse type. • Capacitor: To indicate the unit of capacitor, a symbol P is used: this symbol P means micro-micro-farad and the unit of the capacitor without such a symbol is microfarad. As to electrolytic capacitor, the expression “capacitance/withstand voltage” is used. (CH), (TH), (RH), (UJ): Temperature compensation (ML): Mylar type (P.P.): Polypropylene type • Schematic diagram and Wiring Side of P.W.Board for this model are subject to change for improvement without prior notice. REF. NO DESCRIPTION • The indicated voltage in each section is the one measured by Digital Multimeter between such a section and the chassis with no signal given. 1. In the tuner section, ( ) indicates AM < > indicates FM stereo 2. In the main section, a tape is being played back. 3. In the deck section, a tape is being played back. ( ) indicates the record state. 4. In the power section, a tape is being played back. 5. In the CD section, the CD is stopped. • Parts marked with “ ”( ) are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. POSITION REF. NO NSW801 PICKUP IN ON—OFF SW721 MEMORY/SET ON—OFF SW700 JOG ON—OFF SW722 BASS/TREBLE ON—OFF SW709 ON/STAND-BY ON—OFF SW723 BAND ON—OFF SW710 CLOCK/TIMER/SLEEP ON—OFF SW724 REC. PAUSE ON—OFF SW711 TUNING UP ON—OFF SW725 STOP/CLEAR ON—OFF SW712 PLAY/CD PAUSE ON—OFF SW726 TUNING DOWN ON—OFF SW713 VOLUME SELECT ON—OFF SW727 FUNCTION ON—OFF SW714 DISPLAY MODE ON—OFF SW728 VOLUME JOG ON—OFF SW715 ASPM ON—OFF SW730 CD LID OPEN/CLOSE ON—OFF SW716 EON ON—OFF SW802 CD LID ON—OFF SW717 PTY. TI ON—OFF SW901 FOOL PROOF ON—OFF SW718 SURROUND ON—OFF SW902 CAM ON—OFF FRONT VIEW E C B (S) (G) (D) (1) (2) (3) 2SB562 C 2SC2001 K 2SC380 O 2SD468 C 2SK246 GR KRA102 M KRC102 M KRC104 M KRC107 M KTA1266 GR KTC3199 GR FRONT VIEW DESCRIPTION POSITION FRONT VIEW B C E 2SD2012 Y MPG3372X HY2043 Figure 21 TYPES OF TRANSISTOR AND LED – 21 – 1 2 3 SVC348S XL-60H/70H CNP301 FM MUTE LEVEL VR351 10K(B) AM ANT VD301-1 SVC348S SWITCHING R_MUTE Q351 AM OSC OUT 3 4 5 17 FM/AM OUT VSM AM LOW CUT 18 6 FM DET STEREO SD GND IC303 FM IF DET./FM MPX./AM IF LA1832 9 8 AM MIX OUT AM IF IN 7 16 14 13 15 MO/ST 2 19 MPX VCO 1 AM OSC. 20 VCC AM IF IN FM AFC REG AM RF IN AM OSC OUT 21 23 FM IF IN 22 24 AM MIX OUT AM OSC IN VD301-2 SVC348S T306 X351 456kHz L-CH OUT T302 PHASE (AM/FM) BALUN R-CH OUT L341 2 MPX IN 1 2 PHASE 1 IF OUT AM LOOP ANTENNA 10 11 12 +5V AM IF T351 3 1 ZD351 MTZJ5.1B CF351 FM IF CF352 2 +5V A_12V A_GND 2 CF301 CF302 1 3 1 3 FM IF FM IF TP301 Q301 VT FM ANTENNA TERMINAL SO301 VT R-MUTE L-CH 1 7 8 9 Q101-Q104 SWITCHING NC IF IN FM 6 IF REQ DO 5 FM CL 4 SW AM IN PD 3 MO/ST AIN DI 1 2 IC101 HEAD SELECTOR BA3126N 15 14 13 12 17 16 FM IN 18 IC302 LC72131 PLL CONTROLLER MUTE 19 VDD 22 21 20 CE VT X352 4.5MHz VSS 4 X IN FE301 FM FRONT END IF OUT F OUT VCC GND GND GND ANT. 1 3 X OUT FM IF 5 NC FM+B 8 7 6 2 AOUT D_GND VT IC102 REC./P.B. EQUALIZER AMP. 3 L-IN 5 150K CNS101 1 2 3 4 5 6 7 8 L-CH RECORD/ PLAYBACK HEAD R-CH ERASE HEAD 2 CNP101 L-CH 1 2 3 4 5 6 7 8 L-CH 3 L-CH 4 A-GND A-GND A-12V R-CH ERASE 6 R-CH 7 A-GND 9 REC MUTE 1 IC102 BA3311L 8 Q105 Q106 A_12V REC 10 P/B SW CONT MUTE R-IN IC101 ALC 2 + - 9 ALC 150K P/B SW 11 8 R-CH L-OUT + 5 R-CH A_12V Q360 10 11 NF REC SW FM+B FM RIPPLE FILTER 6 7 12 R-OUT NF REC SW SWITCHING A_12V Q151 L151 Q152 BIAS OSC Q171 SWITCHING SWITCHING REC Q153 Q172 SWITCHING REC BIAS CONT SWITCHING RUN PLS Q903 SOL M_12V PH901 PHOTE INTERRUPTER U_CON5V SOL901 SOLENOID SW902 CAM CNP901 SOLENOID DRIVER Q902 CAM SW Q901 CNS901 M_GND Q904 TAPE MOTOR DRIVER SWITCHING CNP703 1 2 3 4 5 6 7 8 9 TO DISPLAY PWB SWITCHING Figure 22 BLOCK DIAGRAM (1/4) – 22 – Q905 D-GND MOT P.F U_CON 5V SW901 FOOL PROOF M 12V 2 SOL 1 Q906 RUN_PLS 2 SWITCHING MOT 1 - 7 6 5 4 3 2 1 REC + 7 6 5 4 3 2 1 SURROUND M CFW901 B-CAN(NC) BIAS M901 TAPE MOTOR XL-60H/70H E IC201 KIA4558P SURROUND CONTROL R-CH IN R-CH OUT A_12V 6 5 7 8 Q201 IC201 KIA4558P 16 15 14 13 11 12 10 9 IC521 RDS CIRUIT LC72723M AMP. 1 2 4 3 5 4 X521 456kHz 6 7 2 3 1 Q203 8 L-CH OUT SURROUND ON/OFF Q521 L-CH IN A GND CONT A_12V 12V DO CL CE DI CD+B P MUTE P-STB CNS704 AUX R TAPE R TUN R CD R 13 11 12 IC401 LC75342M R-CH 10 8 9 6 7 5 4 3 2 1 LOGIC FUNCTION/VOLUME EQUALIZER NC SO401 VIDEO/ AUX INPUT UTE 14 15 DI FM ST R-CH OUT REC R CH 9 8 7 6 TO DISPLAY PWB 5 4 3 2 1 CE SD 12 11 10 VSS VSM VDD RDS CLK RDS DATA L-CH 19 18 17 20 21 22 23 24 25 26 27 29 28 30 CL 16 CD L TUN L TAPE L A_12V AUX L REC L CH L-CH OUT A_12V STEREO SD REC L/R CH L-CH IN TAPE L/R CH R-CH IN 13 2 L-CH OUT 9 5 R-CH OUT 8 Q601 Q602 + SO601 SPEAKER TERMINALS + IC601 LA4451 POWER AMP. 14 NF REC L-CH J601 HEADPHONES L-CH 3 MUTE 4 11 VCC CNP651 P-CONT CNS651 7 12 2 2 1 1 D651~D654 F651 T3.15A L 250V T651 MAIN POWER TRANSFORMER GND D656~D659 CD_6.2V CNP652 Q607 F652 T1.25A L 250V CNS652 1 2 2 1 GND Q606 T.F GND VOLTAGE REGULATOR Q608 Q609 VOLTAGE REGULATOR Q683 CD+B CNP707 MECHA 12V (M_12V) FROM DISPLAY PWB Q605 Q682 3 RLY681 Q681 2 1 LF651 LINE FILTER AUDIO 12V Q604 (A_12V) 6 7 8 9 10 11 12 SPLAY PWB D_GND CD_6.2V M-GND M_12V CD R A-GND CD L TAPE SW D-GND A_12V M_12V U_CON 5V SOL MOT Q603 1 2 3 4 5 6 7 CNP605 TO CD SERVO PWB Figure 23 BLOCK DIAGRAM (2/4) – 23 – D681~D684 T681 SUB POWER TRANSFORMER SO651 AC POWER INPUT SOCKET AC230V,50Hz XL-60H/70H 1 ~ 4 39 ~ 42 X701 8MHz X702 32.768kHz SW700 JOG CNP706 UP C A DOWN B 1 2 2 3 3 SEG6 SEG5 SEG4 SEG3 SEG2 VLC1 VDD OSC2 OSC1 VSS XI XO VREF 17 KEY1 SW711-SW718 18 KEY2 SW721-SW728 19 MODEL 20 CLID_PRO 21 NC DI RESET REC DO 24 VREF+ 25 SOL CFW701 MOT 22 TAPE_SW 23 VSM CE 2 VLC2 CL 1 VLC3 16 CLID_SW SW709-SW710 D_GND 2 COM0 14 MMOD KEY D701-709 LED 1 COM1 15 CNS706 1 1 2 3 4 5 6 7 8 9 10 11 12 13 SEG1 COM2 SEG0 100 99 98 97 96 95 94 COM3 26 27 28 29 30 31 32 D_GND 3 RX701 REMOTE SENSOR M_12V 2 3 2 Q708 1 1 TO POWER PWB CNS707 U-COM VDD U-CON+5V SYS STOP SWITCHING REMOCON RESET A_12V Q707 Q709 LED+B P CONT RESET D_GND SWITCHING SWITCHING Q702 Q701 Q703 SWITCHING Q706 SW730 CD LID OPEN/CLOSE CFW807 1 2 2 M_GND CFW806 1 1 3 3 +5V CD_6.2V Q861 IC805 TA7291S NC SW802 CD LID IC805 TA7291S MOTOR DRIVER M_GND 7 8 9 SP- 6 SL- 5 SL+ 1 3 4 FMO 1 2 2 15 14 13 12 11 10 9 IC804 LA6541D FOCUS/ TRACKING/ SPIN/SLED DRIVER 2 M_12V M801 CD LID MOTOR REG. 8 7 6 - + 4 5 - + - - + + IC804 LA6541D + - + - RESET + CD RES D_GND REG IN REG OUT CNS804 M CNP804 1 SP+ 1 - - + FO+ FO- TR+ TR- TRO 16 17 18 19 20 21 22 23 24 25 26 27 +5V X801 16.93MHz M_GND 3 2 1 3 2 1 CNP805 3 J801 CD DIGITAL OUTPUT 3 2 1 BI805 1 2 CNS805 RFGC FVO FMO TEBC SEL DMO FLGA 2VREF FLGB FLGC FLGD IO0 VDD IO1 VSS IO2 IO3 /CKSE /DMOUT TESIN /DACT PXI VSS TESI01 PXO XI VDD XVSS XO XVDD VREF TRO FOO TEI TSIN RFRP RFZI RFCT AVDD 37 SLCO 36 AVSS 35 VCOF TMAX TMAXS 7 8 PDO 6 ZDET 5 HSSW 4 P2VREF 3 TESI00 2 VDD 1 MONIT 34 VCOREF 33 PVREF 32 LPFO COFS 97 98 100 +5V RFI 38 D_GND 31 LPFN 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 +5V D_GND Figure 24 BLOCK DIAGRAM (3/4) – 24 – 13 14 15 16 RFRP 17 18 RFI 19 RFGC 20 21 22 23 24 FEI FEI 94 99 SBAD SBAD 93 96 IC801 TA2109F SERVO PRE AMP. TEZI 95 SPDA /RST 39 SPCK /TSMOD 41 40 SBSY TEST4 92 42 SFSY /CCE 91 DATA BUCK 89 90 VSS VSS IC802 TC9462F SERVO/SIGNAL CONTROL VDD VDD 43 CLCK BUS3 44 88 SBOK BUS2 45 87 IPF BUS1 86 MBOV BUS0 46 DOUT TEST3 85 AOUT TEST2 47 BCK TEST1 A_GND 84 VSS DVSL 48 LRCK LO 50 49 83 EMPH DVR /UHSO DVDD +5V 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 81 82 /HSO RO TEST0 DVSR D_GND D_GND SBAD TEO FEO TEN FEN 2VRO VRO TEB RFRP SEL RFIS LDO RFGO MDI RFGC TN1 AGCI TPI RFO FPI GND FNI RFN VCC 12 11 10 9 8 7 6 5 4 3 2 1 TEI TEBC SEL E F B A CD +5V XL-60H/70H LCD701 LCD DISPLAY 1 ~ 4 5 ~ 38 39 ~ 42 CL ID_DW CLID_UP CLID_PRO 02 768kHz SEG24 SEG23 SEG22 SEG21 SEG20 SEG19 SEG18 SEG17 SEG16 SEG15 SEG14 SEG13 SEG12 SEG9 SEG11 SEG8 SEG27 73 COM0 SEG28 72 VLC3 SEG29 71 VLC2 SEG30 70 VLC1 SEG31 69 VDD SEG32 68 OSC2 SEG33 67 OSC1 CCE 66 XO 14 MMOD VREF 18 KEY2 PU_IN 58 CLID_DW CLID_UP 57 56 MVOL_DW 55 19 MODEL 20 CLID_PRO BUS0 PU_IN 8 7 TO CD PWB 6 5 4 3 2 1 CNS702 TAPE_SW A_12V 1 2 3 4 6 5 8 7 D_GND U_CON5V SOL MOT 9 REC NC MVOL_IND 53 MVOL_DW NC 52 DATA P_CONT CD+B P_MUTE P_STB M_12V IC702 TA7291S LOADING MOTOR DRIVER MVOL_UP 54 SURR JOG DOWN JOG UP CLE REMOCON SYS STOP POWER B_CAN RUN_PLS CLOCK RESET REC MOT SOL CE BIAS 21 NC CL BUS1 CD_STB BUS0 61 CD_RES 59 KEY1 DO BUS2 9 BUS1 62 CD_STB 60 51 RUN_PLS D_GND BIAS MVOL_UP BACK LIGHT M701 JOG MOTOR 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 STEREO DI BUS3 11 10 BUS2 63 16 CLID_SW 24 VREF+ 25 CCE BUCK 13 12 BUS3 64 17 22 TAPE_SW 23 VSM CD_RES BUCK 65 IC701 IX0026SJ SYSTEM CONTROL MICROCOMPUTER XI 15 SEG10 SEG7 SEG6 SEG5 SEG4 SEG3 COM1 VSS CL ID_SW 75 SEG25 74 SEG26 M_12V SD 01 Hz 1 2 3 4 5 6 7 8 9 10 11 12 13 SEG2 COM2 SEG1 COM3 SEG0 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 2 2 1 1 CNP705 B_CAN SURROUND M 12 11 10 9 8 7 6 TO MAIN PWB 5 4 3 2 1 CNS703 CNS705 CLE 12 DATA VSM SD STEREO DO TO MAIN PWB CL CE DI CD+B P_MUTE P_STB 1 CFW704 CL ID_DW CLID_UP CLID_PRO CL ID_SW CD_RES CCE BUCK BUS3 BUS2 BUS1 BUS0 CD_STB CD_6.2V PU_IN 13 12 11 10 9 8 7 FROM DISPLAY PWB 6 5 4 3 2 1 REG. D S/ NG/ ED R DMO 4 5 - 3 + - 2 CL ID_L 1 A_GND VCC 7 6 CD_6.2V MUTE 8 - + SP+ SP- SL- SL+ FMO REG IN REG OUT 15 14 13 12 11 10 9 CD STB CNP702 M_GND CD_R M_GND - + + M_12V IC804 LA6541D D_GND CD_6.2V + - + - - - 3 TO MAIN PWB 5 6 7 VCC CD RES + 2 4 CNS605 + - RESET 1 + FOO FO+ FO- TR+ TR- TRO 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 CD_6.2V SP+ M_GND SPSL+ SLPU-IN M_GND 6 6 6 5 5 5 4 4 3 3 2 2 1 1 1 CNS803 IC801 TA2109F SERVO PRE AMP. - SP- M NM802 SPINDLE MOTOR M NM801 SLED MOTOR SL+ 4 3 2 + SP+ + SL- - PU-IN GND NSW801 PICKUP IN CNP803 PICKUP UNIT CNS801 SBAD 13 14 15 16 RFRP 17 18 RFI 19 RFGC 20 21 22 23 24 FEI SBAD TEO FEO TEN FEN 2VRO VRO TEB RFRP SEL RFIS LDO RFGO MDI RFGC TN1 AGCI TPI RFO FPI GND FNI RFN VCC 12 11 10 9 8 7 6 5 4 3 2 1 TEI TRTR+ FO+ TEBC FO- SWITCHING D-GND SEL Q801 +5V P VR E LD F 1 1 1 2 2 2 3 3 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 TR- TR+ TR+ FO+ FO+ FO- FO- TR- GND ACTUATOR PD V LD B A 1/2VCC CD +5V CNS802 D_GND 1 2 3 4 5 VREF +5V 6 7 C F B A E 1/2V +5V 1 2 1 2 3 3 4 4 5 5 6 6 7 7 C F B A E 1/2V +5V Figure 25 BLOCK DIAGRAM (4/4) – 25 – C F B A E GND MON LD VCC XL-60H/70H AM TRACKING fL R363 6.8K R364 6.8K C373 0.015 PHASE MO/ST (AM/FM) (2.2V) 4V 1.3V 1.3V L-CH OUT R355 3.8V 3.3K (1.2V) 3.8V (1.9V) R366 2.2K 12 C358 1/50 C357 2.2/50 C355 22P R376 10K C370 1/50 C356 0.001 FM IF 13 PHASE R-C OUT MPX IN MPX VCO VCC 5V 0V 10 11 AM IF ZD351 MTZJ5.1B +B +B 2 C374 0.015 R357 470K R356 1K C368 1/50 2.1V 2.3V (0V) C354 0.022 CF351 CF352 2 T351 AM IF 9 3 C372 1/50 15 14 16 C398 100/10 FM DET 0V 3 1 R353 2.9V C399 270 (4.3V) 0.022 STEREO 8 C369 56P R350 2.7K 0.6V 2.1V (2.7V) C367 1/50 SD 7 5V GND 6 C371 1/50 R361 12K Q351 1 KRC104 M 4.7V (0V) 2 R362 12K IF OUT C366 0.001 C364 10/16 C365 0.022 C361 0.022 2.1V (2.7V) 0V (0.9V) 5 5V AM OSC IN REO R352 1K 2 CF302 FM IF FM 9 10 C383 0.022 C386 330P FM RIPPLE FILTER 11.7V R383 5.6K 10.9V R365 10K IF IN Q360 KTA1266 GR 10.8V R385 5.6K R384 6.8K IF REQ MUTE MO/ST FM 8 R373 1K NC NC AM IN DO 7 C391 47/16 11 3.5V (0V) 3.7V (0V) 3.9V DI CL 6 5.1V 5 C384 0.001 R392 390 0V 2.6V (0V) 0V (2.6V) 5.2V VDD 0.9V R379 2.2K 17 16 15 14 13 12 18 AIN C385 0.01 3 4 CE 2 0.1V 1 19 IC302 PLL(TUNER) LC72131 R374 1K 0.1V VSS NC C382 15P(CH) X IN 2.6V X352 4.5MHz AOUT X OUT 22 21 20 0V CD SIGNAL 2.6V C381 12P(CH) RECORD SIGNAL 0.9V C393 1/50 PLAYBACK SIGNAL PD AM SIGNAL FM IN TP301 R387 5.6K R377 5.6K C395 0.022 L351 100µH R380 1.5K VT C396 100/10 R391 390 R381 10K R386 330 R393 1K 1.7V (11.4V) +B C387 0.022 R382 330 R395 47K L352 100µH FM SIGNAL C C350 0.022 C353 0.022 C351 0.022 R348 680 4 2.1V 4.8V R345 4.7K C347 0.022 AM IF IN 2.1V C380 10/16 FM IF CF301 3 1 R344 680 17 2.3V R359 1.8K D522 1N4148 R360 4.7K R372 1K R371 1K R343 180 C345 0.022 C346 0.022 SO301 FM ANTENNA SOCKET 75 OHMS C348 100/16 C349 0.001 C376 0.001 19 18 C392 0.001 R346 330 9.5V Q301 2SC380 O L342 2.2mH 3 3 1 +B C301 0.001 2 X351 456KHz AM LO FM/AM OUT CUT C394 47/16 R369B 82 1 C341 0.022 20 VSM IC303 FM IF DET./FM MPX./AM IF LA1832S C397 0.022 2 5V 2.5V 3 21 C352 10/16 4 1 22 FM AFC AM RF IN C344 33P R369A 68 D304 1N4148 9V 2.1V FE301 FM FRONT END D303 1N4148 8 7 6 5 B FM IF AM OSC IN OUT AM OSC. R349 33 1 2 24 23 C360 0.022 AM MIX OUT T306 R336 10K C334 27P(UJ) R351 5.6K C337 0.022 CNP301 C335 560P R347 6.8K 2 L341 BALUN R323 68K 0.8V 1 +B AM BAND COVERAGE fL SWITCHING L354 L353 1mH +B D302 1N4148 AM LOOP ANTENNA 8.2K VR351 10K(B) VD301 SVC348S C329 0.022 D301 1N4148 2.5V A C332 0.022 C331 0.047 T302 C343 33P C362 3.3/50 C302 0.001 FM MUTE LEVEL R358 C363 0.022 LOW PASS FILTER C330 12P(CH) 5V AM ANT +B +B D REC L R115 15K REC R 7 0V 8 0V 9 0V 0.3V (0.8V) R122 4.7K 5 0V C106 270P R151 47K SWITCHING Q152 KTA1266 GR 8.3V C153 0.0039 0V 0V 4.6V 11 6 7 12 2 C112 10/16 R112 2.2K C110 0.015 (ML) Q106 KTC3199 GR REC MUTE R108 10K 0.7V R110 3.9K R132 4.7K R106 150K R155 R153 56 10K REC. BIAS D104 1N4148 3 L151 330µH C154 0.027 (ML) C108 47/16 R104 120 R154 10K 2.6V (0V) Q151 2SC2001 K C155 100/16 Q171 Q172 KRA102 M KRC102 M SWITCHING R152 100K 2 Q153 1 KRC104 M 4.7V (0V) 3 BIAS OSC 11.7V (0V) 3 2 2 (11.7V) 0V R157 150 R156 150 SOL901 SOLENOID R910 33K R902 56K +B C903 100/25 R901 1.5K SOLENOID DRIVER M 12V C905 0.022 0V 3 2 1 11.8V D904 1N4148 R906 1.5K C901 0.001 +B C904 0.022 Q906 2 KRA102 M 4.9V 1 4.4V Q905 2SB562 C 11.7V SWITCHING SWITCHING 2 3 1 3 0.6V 11.8V +B TAPE MOTOR DRIVER 11.7V +B 4.9V Q903 R905 C902 KRC107 M 10K 3.3/50 2 3 3.2V 0.7V SWITCHING 1 0V Q902 2SB562 C 11.9V R909 18K Q904 KRC102 M SW901 FOOL PROOF SW902 CAM R903 47K R907 11.7V 10K Q901 KRC102 M 2 7 6 5 4 3 2 1 D902 1N4148 - 2 7 6 5 4 3 2 1 D901 1N4148 M 7 6 5 4 3 2 1 BI901 1 PH901 PHOTE INTERRUPTER CNS901 + 1 R904 270 TAPE MECHANISM PWB-D/E CNP901 CFM901 M901 TAPE MOTOR SURROUND MAIN PWB-A1 G R133 1K R141 330 C125 100/25 C123 2.2/50 0.6V 7.8V (0V) 1 0V 8 10.1V 10 IC102 BA3311L REC./P.B. EQUALIZER AMP. 0V R134 100K R125 100K C117 10/16 C122 82P 1 10.2V C104 330P R116 15K F C126 22/16 1 4.6V NC C116 0.0022 R120 100 9 R102 1K 4 0.6V C103 330P 0.3V (0.8V) R124 4.7K 3 C105 270P C130 4.7/25 R118 22K 1.5V (0V) D903 1N4148 SWITCHING MOT 8V (10V) C115 0.0022 SOL 6 R126 5.6K R113 3.3K R131 4.7K REC MUTE TAPE_SW 1 2 3 4 5 6 7 H CNS703 P29 12-E TO DISPLAY PWB • NOTES ON SCHEMATIC DIAGRAM can be found on page 21. 1 2 3 4 Figure 26 SCHEMATIC DIAGRAM (1/6) – 26 – 5 6 U CON5V 0V R119 100 Q105 KTC3199 GR R114 3.3K 5 0.3V 0.3V (0.8V) (0.8V) R123 4.7K SWITCHING Q102 Q104 KTC3199 GR KTC3199 GR R121 4.7K 0.7V C111 10/16 REC 4 0.3V (8.3V) R109 3.9K C109 0.015 (ML) C107 47/16 BIAS 0V C129 4.7/25 R117 22K RUN_PLS 3 R107 10K R103 120 SWITCHING Q103 Q101 KTC3199 GR KTC3199 GR 1.5V (0V) TAPE L B_CAN R138 330 ERASE HEAD 0V C114 4.7/25 R139 2.7K C121 82P 2 C113 4.7/25 HEAD SELECTOR R140 10K 0V IC101 BA3126N CNP101 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 R-CH C101 0.001 C102 0.001 L-CH 1 C131 820P E CNS101 RECORD/PLAYBACK HEAD R101 1K TAPE R R111 2.2K R105 150K XL-60H/70H R202 8.2K R529 1K 10V (0V) C525 22P(CH) C524 560P G D201 1N4148 2 S R208 330 8 5.0V R209 10K IC201 KIA4558P 5.0V 4 3 R205 10K (4.4V) 0V ( )SURROUND OFF R210 10K 5.0V 2 5.0V R211 2.7K 1 R215 12K C215 1/50 R217 12K C211 0.0056 C209 47/16 R213 12K R203 100K C213 4.7/50 L IN R201 8.2K C203 1/50 AUX R RDS DATA VSM 0V 2 VSS CE VDD 9.6V DI TEST NC 1 VREF 4.8V 3 CL 5V 4 5 0V 0V C426 0V 10/16 C424 0.1(ML) 4.8V 4.8V 6 ROUT LOUT 4.8V RBS1 LBS1 4.8V LIN RIN 4.8V 7 RBS2 LBS2 4.8V 4.8V R440 3.9K R438 6.8K C420 0.0027 C422 0.1(ML) 4.8V 8 RTRE LTRE 4.8V C418 2.2/50 4.8V C416 4.8V 10/16 L4 9 LSL0 R4 RSL0 4.8V LC75342M R2 4.8V IC401 L3 L2 15 14 13 12 11 10 R3 4.8V P-STB 4.8V C407 10/16 IC401 FUNCTION/ VOLUME EQUALIZER LC75342M C340 0,001 P MUTE 4.8V CD+B R436 10K R418 R420 1K 1K R416 1K C402 10/16 4.8V C411 330P R407 1.5K L1 DI R405 27K R422 1K C404 10/16 NC CE C406 10/16 C412 330P NC SO401 VIDEO/ AUX L-CH CNW704 P29 12-F FROM DISPLAY PWB CL R406 27K CD R R-CH TUN R DO C408 10/16 R408 1.5K FM ST AUX L SD CE DI CL 7 5.0V RDS CLK CNS704 DO 6 5.0V 10.0V Q203 KRC107 M R1 4.8V P_STB P_MUTE CD+B +B R218 1.2K C211 0.0033 12 11 10 9 8 7 6 5 4 3 2 1 TAPE R SD STEREO C216 1/50 L OUT 0.6V 5.0V D 3 8 SURROUND VSM R204 100K R216 1.2K R IN 5 R207 47K 1 DATA R214 12K R OUT X521 456kHz 2.5V 2.3V R212 2.7K C208 100/16 0V 2.5V 0V 5.1V 0V 2.5V 0V C212 0.0033 R206 10K C202 0.0056 C526 22P(CH) 3 CLE C204 1/50 C214 4.7/50 A12V C535 47/16 5.1V C521 10/16 R521 47K L521 2.2mH C522 330P +B D521 1N4148 1.3V 0V 2.5V +B IC201 KIA4558P SURROUND CONTROL +B 9 IC521 LC72723M RDS CIRCUIT 1 2 3 4 5 6 7 R532 10K C536 0.022 C527 0.1 16 15 14 13 12 11 10 2V AMP. R533 56K 2.5V C537 0.022 C523 0.1 2.5V 1.3V 5.1V Q521 KTC3199 GR +B R534 56K Q207 2SK246 GR R528 1K R421 1K R634 3.3K 85 K R424 1K C423 0.1 R439 3.9K R423 1K CL R425 1K CE 91 /16 DI D402 1N4004 D401 1N4004 +B +B C648 0.0012 0V C606 4.7/25 C602 1/50 VCC 12 D601 1N4148 A_GND SO601 SPEAKER TERMINALS C617 0.0022 C633 0.022 R632 6.8 C618 0.0022 R633 10 C632 C639 0.022 470P C640 470P C637 00.22 C693 330P C611 R609 0.22(ML) 3.3 R613 270(1/2W) Q682 2SD468 C D659 D658 C656 0.1 C659 0.1 T.F D685 1N4004 Q681 2SD468 C 5.8V 9.0V ZD682 MTZJ5.6B C688 0.022 C684 0.047 R682 1.2K R681 47 4.9V C685 47/16 R686 47K RLY601 ZD681 MTZJ6.8A C683 2200/16 D681~D684:1N4004 2 1 NC 2 1 D683 D681 LF651 LINE FILTER D684 T681 SUB POWER TRANSFORMER C696 0.001 NC (229) TO TAPE MECHANISM CHASSIS D682 C660 0.001 TO MAIN CHASSIS CNP653 9 C658 0.1 R683 47 C686 0.022 3 2 1 R629 820 13V R628 100 D656 9.0V R684 1.2K 5.6V Q683 KTC3199 GR R685 0.8V (0V) 10K C695 0.001 Q603 KTC3199 GR 20V CNS605 P31 12-C FROM CD SERVO PWB F652 T1.25A L 250V C657 D657 0.1 6.4V Q681~Q683: VOLTAGE REGULATOR +B 1 2 3 4 5 6 7 CNP605 C651 0.1 B2 GND 0.2V (5.2V) FROM DISPLAY PWB CN707 P28 1-F GND2 ZD601 MTZJ13A D651 +B2 1 2 C689 47/16 CNP652 BI652 1 2 +B R619 47 12.3V R617 33K GND1 1 1 2 CNS652 3 GND3 D602 1N4148 D603 1N4148 10 T651 MAIN POWER TRANSFORMER D654 D653 D651~5654:1N5402M D656~D659:1N4004 0V 20V R620 47 C621 100/25 5 F651 T3.15A L 250V C654 0.1 R651 680(3W) CNP707 0V Q604 2SD2012 Y 11.7V 20V R621 22K D652 4.5V ZD602 MTZJ7.5C R625 10K C626 47/16 Q609 KRC107 M 0V 3 Q608 KRA102 M 2 Q683~Q685 VOLTAGE REGULATOR R623 22K C624 0.022 C625 10/16 C622 0.022 CD_6.2V D_GND M_GND M_12V CD_R A_GND CD_L J601 HEADPHONES 4 1 POWER PWB-B1 31.5V R624 1K 11.7V Q605 2SD2012 Y A_12V M_12V U_CON5V D_GND MOT 5 1 9 1 1 2 Q686~Q689 VOLTAGE REGULATOR C630 4700/25 7.8V 1 +B +B REC BI651 C620 470/25 C627 0.022 R627 10K D604 1N4148 +B 3 2 R661 330 +B 2 8 R662 330 1 2 CNS651 1 2 7.5V CNP703 5 CNP651 Q606 KTC3199 GR +B HEADPHONES PWB-A5 C616 2200/50 +B CD TEST POINT R-CH SP604 C662 820P C661 820P Q607 2SD2012 Y 6.2V 20V +B SOL R631 6.8 C615 0.022 SPEAKERS L-CH +B 7 C614 1000/35 16.0V 7 31.5V + SP602 WOOFER 4 Ohm TWEETER 5 3.3V STAND-BY R608 1K L-CH SP601 WOOFER 4 Ohm L603 10µH 9 TWEETER + C663 820P 10 C629 220/50 L602 0.3mH CFW601 6 SP603 C636 0.022 C694 330P 8 30.0V R-CH C644 0.022 (ML) 4 28.0V R614 270(1/2W) R602 4.7K 0V R606 0V 82 C608 220/25 1.2V C643 0.22(ML) 3 D614 1N4004 D612 C612 1N4004 0.22(ML) R604 10K D613 1N4004 1 28.0V R610 3.3 Q601 KTC3199 GR 14 Q602 KTC3199 GR 10 11 12 13 1.2V C607 220/25 R605 82 C604 100P 10 11 12 13 R616 4.7K 1 2 3 4 5 6 7 8 9 16.0V CNP604 +B 1 2 3 4 5 6 7 8 9 2 11 R607 6.8K R113 3.3K C601 33/16 CNS604 TAPE L R603 10K 0V C613 1000/35 C609 47/50 C610 47/50 J923 120 J920 120 REC R C603 100P 13 REC L C647 330P IC601 LA4451 D611 1N4004 C605 4.7/25 R615 4.7K TAPE R IC601 POWER AMP. LA4451 POWER AMP.PWB-B2 R601 1K WB +B L601 0.3mH +B 5 6 7 8 9 10 11 12 D403 1N4004 10/16 V C425 10/16 C430 100/16 C405 R435 10K C429 33/16 TAPE L R417 R419 1K 1K C421 0.1(ML) 10/16 C419 0.0027 C403 R437 6.8K TUN L C417 2.2/50 R415 1K C401 10/16 CD L 266 GR 0.8V C415 10/16 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 SO651 AC POWER INPUT SOCKET AC230V,50Hz When servicing,pay attention as the area enclosed by this line ( ) is directly connected with AC main voltage. 10 Figure 27 SCHEMATIC DIAGRAM (2/6) – 27 – 11 12 SW728 VOLUME/JOG SW714 DISPLAY MODE R717 2.2K SW723 BAND R709 1.5K SW713 VOLUME SELECT R718 1.5K SW722 BASS/TREBLE R710 1.2K SW712 PLAY/CD PAUSE R719 1.2K R711 1.2K SW711 TUNING UP 100 2 Q708 KTA1266 GR SWITCHING +B SW721 MEMORY/SET D730 HY2043 D736 HY2043 SWITCHING Q709 KRC102 M D732 HY2043 3 R7B3 2.2K R796 180 D737 HY2043 R795 180 1 SW710 CLOCK/TIMER/SLEEP R797 180 C SW709 ON/STAND-BY SW700 JOG CNP706 CNS706 1 2 3 C A B R728 1K C703 0.022 R702 10K +B X701 8 MHz X702 32.768kHz +B BI706 JOG SWITCH PWB-A7 1 2 3 R727 47K R723 47K +B R701 10K C701 22P (CH) 1 2 3 C702 22P (CH) R724 1.2K R731 1K R732 1K R733 1K IC702 LOADING MOTOR DRIVER TA7291S 7 8 9 R721 10K CNP705 R722 10K C771 47/16 C772 0.1 2 MVOL_DW R799 2.2K E COM2 2.5V 3 COM1 2.5V 4 COM0 2.5V 5 VLC3 0V 6 VLC2 1.7V 7 VLC1 3.3V 8 VDD 9 OSC2 2.6V 10 OSC1 2.6V 11 VSS 0V 12 XI 13 XO 1.9V 14 MMOD 0V 5V 2.4V 15 VREF 16 CLID_SW 0V 17 KEY1 5V 18 KEY2 5V 19 MODEL 5V 20 CLID_PRO 21 NC 22 TAPE_SW 5V 23 VSM 0.6V 24 VREF+ 5V 26 27 28 29 30 31 32 3 MVOL_UP R798 8.2K 1 2 DI 25 0V R737 1K 2 M701 JOG MOTOR R725 10K 6 R787 2.2(1/2W) 1 1 5 +B CNS705 M 0V 4 2.5V 3 0V NC 2 11.7V 0V 1 R734 1K R735 1K 0V 11.7V IC702 0V D R729 47K R738 1K R7B2 47K R794 180 R730 1K 2 R720 1.2K L701 100µH 1 99 98 97 96 95 94 9 SEG0 COM3 2.5V R739 1K CFW701 +B +B C773 47/16 F +B BI707 TO POWER CNP707 P27 10-G PWB +B 1 1 2 2 3 3 CNS707 +B +B D723 1N4148 D722 1N4148 R7A5 10K C711 RESET 3.3/50 Q701 KRC102 M 3 D721 1N4148 C710 0.01 C715 100/10 R7A4 120 Q703 KTC3199 GR SWITCHING 1 R7A2 100K C712 0.01 G R7A6 1K R7A8 82 R7A3 100 RX701 REMOTE SENSOR Q702 KTC3199 GR SWITCHING 2 R7A7 1K R7B0 10K ZD701 MTZJ3.3B D720 1N4148 R7A0 1K R7A9 3.3K 1 R7A1 1K C714 560P 2 +B +B R778 47K 3 R779 47K C713 10/16 R780 47K R781 47K R782 33K SWITCHING Q707 KTA1266 GR R783 33K +B Q706 KRC102 M R792 47K +B SWITCHING 2 R793 2.2K 3 C704 0.022 1 H • NOTES ON SCHEMATIC DIAGRAM can be found on page 21. 1 2 3 4 Figure 28 SCHEMATIC DIAGRAM (3/6) – 28 – 5 6 R743 1K R746 1K R744 1K R745 LED PWB-A4 2.5V SEG6 R708 2.2K 2.5V SEG5 SW724 REC. PAUSE RESET 5V R716 2.7K 2.5V SEG4 SW715 ASPM 9 10 11 1 REC 0V R707 2.7K 2.5V SEG3 SW725 STOP/ CLEAR 7 8 MOT 5V R715 3.9K 6 5 2.5V SEG2 R706 3.9K SW716 EON 3 4 SOL 0V SW726 TUNING DOWN 2 1 2.5V SEG1 R714 5.6K CE 0V SW717 PTY.PI CL 5V R705 5.6K DO 5V SW727 FUNCTION 2 1 B SW718 SURROUND R740 1K R741 1K R775 1K A DISPLAY PWB-A2 D703 D702 R7D2 R7E1 D701 R7D4 MPG3372X 82 MPG3372X 82 MPG3372X 82 D709 D708 D707 R7D5 R7D3 MPG3372X 82 MPG3372X 82 MPG3372X R7D8 82 D705 D704 D706 R7D9 R7D1 R7D6 MPG3372X 82 MPG3372X 82 MPG3372X 82 XL-60H/70H XL-60H/70H LCD701 LCD DISPLAY 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 74 2.5V SEG27 73 2.5V SEG28 72 2.5V SEG29 71 2.5V SEG30 70 2.5V SEG31 69 2.5V SEG32 68 2.5V SEG33 67 5V CCE 66 4V BUCK IC701 IX0026SJ SYSTEM CONTROL MICROCOMPUTER 64 4.3V BUS2 63 4.3V BUS0 61 60 5V CD_RES 59 PU_IN 58 CLID_DW 57 CLID_UP 56 55 0V MVOL_UP 54 STEREO 0V SD 0V DATA 5V BACK_LIGHT NC P_CONT 5V CD+B 5V P_MUTE 0V 4.6V P_STB SURR JOG_DOWN 5V JOG_UP 5V CLE 5V 5V REMOCON 5V SYS_STOP POWER 5V B-CAN BIAS 0V RUN_PLS 0V CLOCK 5V RESET 5V REC 0V SOL 0V MOT 5V 0V MVOL_DW 5V MVOL_IND 5V CLID_SW CD_RES R761 1K R774 1K R762 1K R763 1K R764 1K R765 1K R766 1K R767 1K R768 1K 62 5V CD_STB 5V CLID_UP CDID_PRO 65 4.3V BUS3 4.3V BUS1 CLID_DW BUS3 BUS3 BUS2 BUS2 BUS1 BUS1 BUS0 BUS0 CD_STB CD_STB CD_RES PU_IN A_12V +B +B M_12V D_GND U_CON5V SOL MOT R785 1K REC RUN_PLS R776 1K R777 1K R757 1K R758 1K R759 1K R760 1K R749 1K R750 1K R751 1K R752 1K R753 1K R754 1K R755 1K R742 1K R775 1K 12 11 11 10 10 9 9 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 1 CNS703 TAPE_SW 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 R743 1K R746 1K R744 1K R745 1K R748 1K R747 1K 13 12 R784 47K CLID_DW CLID_UP R773 1K 52 51 CCE BUCK PU_IN R769 1K R770 1K R771 1K R772 1K 53 CCE BUCK 13 BIAS SD B_CAN SURROUND SURROUND CNP702 TO CD PWB P30 1-B 75 SEG26 2.5V CNS702 SEG25 2.5V BI702 SEG24 12 11 10 9 8 7 6 CNP703 TO MAIN PWB P26 6-H 2.5V SEG23 2.5V SEG22 2.5V SEG21 2.5V SEG20 2.5V SEG19 2.5V SEG18 2.5V SEG17 2.5V SEG16 2.5V SEG15 2.5V SEG14 2.5V SEG13 2.5V SEG12 2.5V SEG11 2.5V SEG9 2.5V SEG10 2.5V SEG8 2.5V SEG7 2.5V SEG6 2.5V SEG5 2.5V SEG4 2.5V SEG3 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 2.5V 8 5 4 3 2 1 CLE DATA DATA VSM VSM STEREO 12 CNS704 TO MAIN PWB P27 8-B CLE R789 47K R786 47K BIAS SD RUN_PLS STEREO MVOL_IND DO MVOL_UP CL MVOL_DW CE +B REC DI CD+B CD+B CLID_PRO P_MUTE P_STB P_STB 1 P_MUTE CFW704 MOT SOL CE +B +B CL DO DI TAPE_SW CLID_SW +B +B +B +B 7 8 9 10 Figure 29 SCHEMATIC DIAGRAM (4/6) – 29 – 11 12 XL-60H/70H A IC805 TA7291S NC CD SIGNAL 1 CD LID PWB-A9 2 3 4 5 6 7 9 8 R872 2.2(1/2W) B FROM DISPLAY PWB CNS702 P29 12-C PU_IN 1 2 3 4 5 6 7 8 9 10 11 12 13 1 3 3 R873 5.6K CNP702 CFW806 1 C871 47/16 SW802 CD LID CD_STB BUS0 R874 2.2K BUS1 BUS2 BUS3 BUCK CCE R876 150K R877 68K CLID_SW CLID_PRO R880 47K CLID_UP CLID_DW CD_RES C R813 10 D L803 10µH +B C825 0.056 R817 1K R818 1K R814 3.3K C824 0.056 C826 C827 15P 15P (CH) (CH) R812 3.3K C823 0.01 C819 0.1 C821 0.1 C834 470P 0V C817 0.1 R811 2.2K 15 5V 0V 0V 0V E 0V 4 5V C832 10/16 C831 10/16 C818 0.1 R820 1K R816 10K R815 10K C822 220/10 X801 16.93MHZ C833 470P R810 3.3K BUS1 4.3V BUS2 4.3V BUS3 4.3V VDD VSS 5V 0V 0V NC HSSW 2.1V 1.7V NC COFS NC ZDET 0.6V NC SPDA P2VREF 4.3V 0V NC SPCY TESIOO 0V 0V NC SBSY VDD 5V 2.4V NC SFSY NC MONIT 0V 0V NC DATA VSS 0V VDD 5V 1.2V NC CLCK 0V NC SBOK 5V NC IFP LRCK NC 0V 1.4V 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 5V TESTO NC MBOV 0V EMPH NC NC /RST 4.9V VSS 0V UHSO NC NC TEST4 DOUT 2.5V 3.3V NC AOUT 0V /CCE NC BCK 2.5V BUCK 4V R801 10K R851 330 DIGITAL OUT PWB-A8 CNS805 C852 0.0022 (ML) 3 2 1 3 2 1 CNP805 C851 100/10 3 2 1 BI805 J801 CD DIGITAL OUTPUT L804 0.82µH 12 R806 15K C802 0.015 C863 470P 13 G 1 2 3 R804 100K R802 47K C801 100P C820 0.01 C829 100/10 C838 47/10 +B +B H • NOTES ON SCHEMATIC DIAGRAM can be found on page 21. • The numbers 1 to 17 are waveform numbers shown in page 36. 1 2 3 4 Figure 30 SCHEMATIC DIAGRAM (5/6) – 30 – 5 C813 100/10 BUS0 4.3V 5 FMO 2.1V TEBC 2.1V RFGC 1.8V 2.2V DMO 0V FVO NC 2.5V SEL 7 IC802 TC9462F SERVO/SIGNAL CONTROL C811 47/10 C812 0.01 5V TMAX 2.1V NC TEST3 6 NC TMAXS 2.1V 5V VREF C810 50 2.1V 0.001 R809 49 10K 11 2.2V FOO 48 R808 C809 2.2V TEZI 47 3.3K 0.0047 2.2V TEI 46 2.1V TSIN 45 2.1V SBAD 44 2.2V FEI 43 C807 2.1V RFRP 42 0.033 2.1V RFZI 41 2.1V RFCT 40 R807 10K 5V AVDD 39 C806 0.0047 2.1V RFI 38 C805 2.1V SLCO 37 0.0027 0V AVSS 36 C804 1.4V VCOF 35 0.01 VCOREV 2.1V 34 PVREV C803 2.1V 33 47/10 LPFO 2.1V 32 LPFN 31 2.1V 2.1V TRO PDO 2.1V 5V NC TEST2 4.3V 2VREF 0V FLGA NC 0V FLGC NC 5V FLGB NC 0V VSS 5V VDD 0V FLGD NC IO1 NC IO0 NC IO3 NC IO2 NC /DMOUT NC 0V VSS 0V TESIN 0V TESI01 0V PXI 0V XVSS NC TEST1 100 C837 470P 14 1 16 0V DVSL /DACT NC 2.4V /CKSE NC 2.3V LO 5V PXO NC XVDD 0V XO 2.6V 2.2V XI DVR /HSO C836 100/10 R855 100K R854 100K R853 100K R852 100K C835 0.056 0V 5V F 17 DVDD NC C840 100/10 R819 220 RO 2.4V NC BUS0 BUS1 BUS2 BUS3 BUCK CCE CD_RES C830 0.056 81 82 C828 83 100/10 84 85 86 87 C862 0.0022 88 89 90 91 92 93 94 95 96 97 5V 98 5V /TSMOD 99 5V DVSR 5V VDD 80 79 78 77 76 75 74 73 72 7170 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 0V 6 XL-60H/70H CNP804 1 1 6 CNS804 9 8 CD PWB-A3 IC805 TA7291S MOTOR DRIVER 1 2 2 M M801 CD LID MOTOR C872 0.1 74 K CFW807 1 1 2 2 SW730 CD LID OPEN/CLOSE C861 0.001 CD_L A_GND CD_R L804 2.2µH M_GND M_12V D_GND Q861 2SB562 C 5V 6.3V CD_6.2V C844 0.0068 SP+ 6 5 4 3 2 1 SP- 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 SP+ SL- R863 2.2K +B PU-IN GND 6 5 4 3 2 1 CNP803 C859 470/10 BI803 C860 0.1 6.3V 2.1V 2.1V 3.1V 2.5V 0V 0V 0V 2.8V 2.2V 2 3 2.8V NC 2.1V NC 5V NC 5V C857 47/16 2.1V IC804 LA6541D CNS803 C887 0.0027 6.3V 4.9V 2.2V 2.2V 0V 3.1V 2.5V 0V 0V 2.8V 2.8V 2.2V 2.2V 5.1V 5.6V 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 IC804 LA6541D FOCUS/ TRACKING/ SPIN/SLED DRIVER CNP605 P27 8-H R862 2.2K L801 10µH TO MAIN PWB +B +B R861 2.2K +B 1 2 3 4 5 6 7 R843 1K L803 10µH 1 2 3 4 5 6 7 CNS605 BI605 OPEN/CLOSE SWITCH PWB-A6 6 5 4 3 2 1 CD MOTOR PWB-C + SP+ SP- - SP+ + SLPU-IN - M NM802 SPINDLE MOTOR M NM801 SLED MOTOR GND NSW801 PICKUP IN PICKUP UNIT TR+ TR+ R823 1K C847 0.1 C848 39P R828 1.2K R826 2.7K R827 27K C839 2P R829 68K C850 220/10 4.3V 2.1V 2.1V 2.1V 10 9 2.1V 2.1V 2.1V 8 2.1V 2.5V 3.4V 0V 2.1V 2.1V 1.7V 2.1V 0V 2.1V 5V 2.1V FOGND PD R822 22 R821 150 4.1V 3.4V VR LD BI801 2.1V 12 11 10 9 8 7 6 5 4 3 2 1 C841 100/10 2.1V Q801 KTA1266 GR SWITCHING TRPO+ TR+ PO+ FO- FOGND TR- PD ACTUATOR VR LD GH6C605B3A1 1/2VCC +B C843 0.1 R80E 82K + - C + C863 470P C849 0.056 2.2V 2.2V C855 100/10 R80A 82K R80B 68K R80C 82K R80F 82K R80G 68K IC801 TA2109F SERVO PRE AMP. F B A E VREF +5V +B 1 2 3 4 5 6 7 1 2 3 4 5 6 7 1 2 3 4 5 6 7 BI802 +B C C - F F B + - B + A E A + - 1/2V +5V E GND CNS802 C813 100/10 C812 0.01 C846 0.1 2.1V C842 47/10 2V C845 100/10 13 14 15 16 17 18 19 20 21 22 23 24 IC801 TA2109F R825 82K PO+ R824 27K 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 CNS801 TR- MON LD VCC 7 8 9 10 Figure 31 SCHEMATIC DIAGRAM (6/6) – 31 – 11 12 XL-60H/70H FROM POWER PWB A ANTENNA TERMINALS SO601 SPEAKER TERMINALS R-CH GND FROM POWER SO401 AMP.PWB VIDEO/AUX P35 11-H CNS604 R-CH L-CH L-CH GND CNS652 P35 8-A AM LOOP ANTENNA ANTENNA SO301 FM 75 OHMS CNP301 RD WH BK BK YL BL WH BK RD WH PK WH J601 HEADPHONES HEADPHONES PWB-A5 WH 2 C382 C381 R344 R349 R347 R374 C384 R391 C391 R106 R103 IC102 C110 B B C C R133 R108 E E D104 C112 C108 R104 R110 12 11 10 9 C123 8 7 6 R141 5 4 3 C125 2 1 R109 Q105 Q106 C107 CNP703 R105 C109 TO DISPLAY PWB 12 11 10 9 8 7 6 5 4 3 2 1 CNS703 P33 10-A P35 11-D TO TAPE MECHANISM PWB MAIN PWB-A1 4 Figure 32 WIRING SIDE OF P.W.BOARD (1/4) – 32 – 5 6 FROM DISPLAY PWB P33 12-C R112 R132 R134 CNP901 BK 3 R534 R533 R114 R113 Q103 Q104 R124 C117 R121 C106 C104 C103 C105 C114 C113 R101 R111 Q521 R125 C126 Q101 R126 R102 12 11 10 9 8 7 6 5 4 3 2 1 R131 9 10 GY GY GY GY GY GY BK 7 6 5 4 3 2 1 CNS901 D522 R382 R386 R384 R385 R392 C396 C527 C522 E 16 C 15 B E C B R123 E C B IC101 9 8 7 6 5 4 3 2 1 CFW704 IC521 C115 R117 R119 B C R122 E Q102 R116 L521 C536 C521 1 R107 8 7 6 5 4 3 2 1 R371 R372 X352 R373 R387 R360 R359 L351 C370 C357 ZD351 C523 C524 C525 5 R115 RECOED/ PLAYBACK HEAD CF301 R348 C393 R343 C394 R380 R345 C398 C358 R355 C356 R353 CF351 R352 C535 D521 R532 C111 1 3 2 1 C102 R138 Q171 1 2 3 R120 E C B C131 R139 C101 R140 Q151 C116 R118 C130 CNP101 8 7 6 5 4 3 2 1 R151 R366 R521 8 R377 C395 C129 3 2 1 Q903 C154 C537 Q351 3 2 1 12 11 10 9 8 7 6 5 4 3 2 1 Q360 B C E R383 L352 R395 R528 R529 C526 X521 CNS704 R905 BK GY GY GY GY GY GY Q172 7 C380 R369B R369A C361 R351C350 IC303 C354 R376 C353 C363 R393 R363 R634 C901 R903 R904 C902 E C B R910 R909 C153 D902 D901 Q902 BI901 R902 R157 1 R156 ERASE HEAD 1 C903 L151 3 2 1 Q153 R154 D903 1 2 3 Q904 C904 D201 CNS101 H CF302 R627 C627 3 2 1 R153 C155 Q905 D904 R901 Q901 R907 R906 R208 C905 C215 R207 R201 C208 R217 Q152 B C E E C B Q906 R152 C403 C401 R209 C216 C214 R216 3 2 1 R155 R662 R661 G C661 L603 3 2 1 R213 Q203 R211 C371 C121 C122 5 4 3 2 1 R205 R215 E C B R203 C201 P34 3-C FROM CD PWB IC201 CFW601 C663 CNS605 R210 5 6 7 8 C213 D G S Q201 C211 C212 C416 C418 C202 R438 R218 C209 R204 R212 R206 C204 R214 C422 C420 C424 CFW601 C662 1 R436 F R440 C404 C408 R418 R420 R422 R202 5 C405 C407 10 15 5 C203 IC401 1 C373 X351 C372 1 2 3 45 6 7 C402 C406 R415 R416 20 16 R362 CNP605 R419 C423 C429 C421 R417 C386 1 2 3 CF352 C620 Q609 R628 1 2 3 Q608 R421 R423 C430 C417 C419 R435 C415 R437 C425 D403 1 2 3 R425 R424 C426 R617 R629 R624 R381 R379 12 13 14 15 16 17 18 19 20 21 22 R365 C383 C392 C387 C385 2 23 C351 3 22 4 21 C352 5 20 19 C360 6 C399 7 C367 18 2 8 17 C369 16 9 1 15 10 11 R356 C368 14 13 12 C355 R357 C374 R364 ZD601 C622 1 R350 C365 C366 C621 Q603 E C B D401 D402 1 2 C397 3 T351 R361 D FM MUTE LEVEL TP301 VR351 R336 2 C343 R358 C344 3 24 1 C364 L354 Q301 E C B 11 10 9 8 7 6 5 4 3 2 1 C362 R620 C693 R621 B C E D602 D603 Q604 C630 T306 IC302 C337 C625 B C E 30 25 C348 C341 4 3 2 1 C345 C347 R625 Q605 1 2 CNP652 C346 L353 C626 D604 C332 E C B L342 D301 D302 B C E R623 R619 C624 J923 J920 C E FE301 CNP604 13 12 11 10 9 T302 8 7 6 C329 5 4 C330 VD301 C331 3 2 C334 1 R323 C335 ZD602 Q607 Q606 R439 8 7 6 5 C639 R633 B C694 C301 C349 C302 R407 C411 R405 C640 R346 C376 L341 D304 L601 R631 D303 C633 R406 C636 C632 L602 C617 C637 C412 R408 R632 C618 C340 1 2 XL-60H/70H DISPLAY PWB-A2 TO MAIN PWB P32 6-G R746 R743 R775 R741 R740 R739 1 2 3 4 5 6 7 8 9 10 11 12 CNS703 CLOCK/TIMER/ SW722 SLEEP BASS/ TREBLE SW710 SW718 SURROUND X701 R725 R724 R733 R710 R782 SW721 C701 R728 L701 R732 R731 C703 R722 C702 R723 MEMORY 1 R727 R721 /SET 2 R783 3 R729 95 55 60 1 100 90 65 85 70 80 R761 R774 R762 R763 R764 R765 R766 R767 R768 R769 R770 R771 R772 R773 R785 BI702 1 2 3 4 5 6 7 8 9 R787 R708 R798 SW726 TUNING DOWN SW725 STOP/ CLEAR SW716 EON CNS704 P32 6-F SW727 FUNCTION C772 R706 R707 TO MAIN PWB R799 SW711 TUNING UP SW712 PLAY/CD PAUSE SW715 ASPM C713 R7A1 YL YELLOW GR GREEN BL BLUE VL VIOLET GY GRAY WH(W) WHITE BK BLACK PK PINK D737 D730 CNP705 2 1 CNS705 BK RD R794 D736 3 E C B 1 1 3 R792 WH BK BK 1 2 3 TO POWER PWB CNP707 P35 7-A Q707 GY GY BK CFW701 R793 1 2 3 BI706 CNS707 R795 Q706 BI707 B C E D732 R7B2 Q709 3 2 1 M M701 JOG MOTOR SW713 C715 1 2 RED ORANGE R719 R796 BROWN OR R786 R718 R7B3 Q708 R784 C704 BR RD(R) SW728 VOLUME/ JOG R720 DISPLAY MODE COLOR TABLE 1 WHITE LINE 1 R716 R7A9 C710 R7A7 D722 R7B0 R7A4 D723 R7A8 D721 ZD701 R7A2 D720 Q703 R7A3 E C B C712 P34 1-D 1 1 2 R7A6 R7A5 C711 3 2 1 CNP702 IC702 R715 R709 SW714 TO CD PWB 12 C771 RX701 Q702 CNS702 13 12 11 10 9 8 7 6 5 4 3 2 1 CFW704 12 C773 PTY. TI R751 B C E 3 2 1 SW700 JOG CNS706 CNP706 1 C 2 A 3 B 7 9 D709 R7D3 R7D5 D708 D707 R7D8 D706 R7D9 D705 D704 R7D6 8 D703 R7E1 D702 R7D2 2 CFW701 D701 1 R7D1 LED PWB-A4 R7D4 Q701 SW717 VOLUME SELECT C714 R750 R7A0 R744 R776 R777 R760 R759 R758 R757 R742 R754 R753 3 2 1 LCD701 75 76 SW724 REC PAUSE R705 5 IC701 51 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 10 45 R797 15 40 SW723 BAND 30 20 35 13 R711 R702 R730 R738 R781 R737 R735 R734 26 25 50 GY GY GY GY GY GY GY GY GY GY GY GY BK R779 R780 SW709 ON/STAND/BY X702 R749 R752 R755 R778 R714 R745 R789 R747 R717 R748 R701 CNP703 10 Figure 33 WIRING SIDE OF P.W.BOARD (2/4) – 33 – JOG SWITCH PWB-A7 11 12 XL-60H/70H CD LID PWB-A9 CNP803 SW802 CD LID NSW801 PICK UP IN NM802 SPINDLE MOTOR F3895AF 1 B BK GY GY GY GY GY GY RD WH GY WH GY WH C821 BCE R804 C802 C829 C838 R802 C804 R801 C803 C801 C813 13 12 15 10 C848 R828 C846 20 5 R826 C847 24 R829 1 BI801 RD WH GY WH GY WH GY WH R821 R824 C844 C845 R825 IC801 R827 1 R822 C842 R808 C809 C807 C812 R807 30 31 R862 R861 IC804 R863 C859 C841 C818 55 10 IC802 15 45 20 40 25 35 15 11 1 CNS801 C860 E C B L801 R80B R80G Q801 R80E R80F R80A C826 R814 C819 65 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Q861 R812 R811 51 R810 C817 50 R809 C810 60 C863 BI803 L803 C822 C823 C824 70 95 3 2 CNP805 1 C857 C834 R820 C827 R819 C830 81 80 R855 C831 C840 C887 6 X801 85 75 C851 CNS805 WH 3 BK 2 1 RD 1 90 5 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 R823 13 C828 100 1 14 3 2 R843 R816 C806 C835 F C832 C825 R813 R876 3 C862 C805 E 1 R852 R853 FROM DISPLAY PWB CNS702 P33 12-B 7 R817 1 CFW807 C833 BI605 R815 C861 R818 L804 R854 D 1 2 3 4 5 6 7 8 9 10 11 12 13 1 2 3 4 5 6 2 C820 CNP702 1 2 SW730 CD LID OPEN/CLOSE CNS803 1 2 3 4 5 6 7 C811 R874 R877 R880 C871 17 16 1 CNP605 CNS605 C837 C836 2 1 1 OPEN/CLOSE SWITCH PWB-A6 TO MAIN PWB P32 1-F C850 1 2 3 4 5 6 7 8 8 CNS802 RD 1 WH 2 GY 3 WH 4 GY 5 WH 6 GY 7 1 R80C C849 C843 1 2 3 4 5 6 7 8 9 CNP804 1 8 CFW807 R873 R872 IC805 C872 M 1 4 CFW806 M801 CD LID MOTOR CNS804 BK RD 2 7 NM801 SLED MOTOR R806 3 6 5 4 3 2 1 C839 A C PICKUP UNIT CD MOTOR PWB-C 7 BI802 C855 G C851 WH 3 DIGITAL OUT PWB-A8 3 2 1 J801 CD DIGITAL OUTPUT 1 CD PWB-A3 L802 C852 RD 1 BK H 5 7 6 10 9 8 12 BI805 2 • The numbers 1 to 17 are waveform numbers shown in page 36. 3 4 Figure 34 WIRING SIDE OF P.W.BOARD (3/4) – 34 – 5 6 XL-60H/70H TO MAIN PWB FROM DISPLAY PWB CNP652 P32 1-A CNS707 2 1 CNS651 P33 12-F BR 1 2 CNS652 RD RD BR 2 1 Q683 E C B R651 C656 D658 D659 C659 C658 C657 D651 C651 D652 D654 C654 C695 R686 BI651 D653 R685 D657 BI652 F651 T3.15A L 250V 1 2 3 CNP707 2 D656 POWER PWB-B1 1 T651 MAIN POWER TRANSFORMER F652 T1.25A L 250V LF651 LINE FILTER C688 R683 D685 C689 RLY601 R684 TO MAIN CHASSIS GND Q682 B C E ZD682 (238) Q681 C696 C660 T681 SUB POWER TRANSFORMER E C B C686 SO651 AC POWER INPUT SOCKET AC230V, 50Hz R681 FROM TAPE MECHANISM GND R682 C683 D681 1 2 (229) D682 C685 D684 1 2 T.F. ZD681 D683 CNP653 C684 When servicing, pay attention as the area enclosed by this line ( ) is directly connected with AC main voltage. M901 TAPE MOTOR FROM MAIN PWB CNS901 P32 4-G 7 6 5 4 3 2 1 CFW901 1 1 WH 2 7 RED OR ORANGE YL YELLOW GR GREEN BL BLUE VL VIOLET GY GRAY WH(W) WHITE BK BLACK PK PINK C609 C643 R609 C644 R610 POWER AMP. PWB-B2 C613 C611 D611 D613 D612 CNP651 2 1 D614 R614 CNS604 C614 R602 R604 C602 C612 R606 C616 R616 E C B C610 C608 C629 C606 C607 D601 R607 R608 E C B PH901 BROWN R613 C615 Q602 SOL901 SOLENOID C601 R615 Q601 R603 R601 C605 R605 BR RD(R) IC601 C647 C648 COLOR TABLE TAPE MECHANISM PWB-D SW902 CAM PHOTE INTERRUPTER 14 13 12 11 10 9 8 7 6 5 4 3 2 1 C603 SW901 FOOL PROOF 2 TAPE MECHANISM PWB-E TAPE MECHANISM ASSEMBLY C604 YL BR RD CNP901 RD 8 9 13 12 11 10 9 8 7 6 5 4 3 2 1 TO MAIN PWB CNP604 P32 3-A 10 Figure 35 WIRING SIDE OF P.W.BOARD (4/4) – 35 – 11 12 XL-60H/70H WAVEFORMS OF CD CIRCUIT NO DISC FOCUS SEARCH 1 STOP 12 1 FOO FO+ 13 2 IC804 26pin 3 FO- 14 3 SEL 5 6 1 11 2 TEI 15 3 6 SBAD 11 2 3 TEI 1 TRO 2 IC802 49pin RFO 15 3 FMO 3 IC802 53pin IC801 22pin STOP PLAY REVIEW 6 1 FEI TEI 1 TRO 2 IC802 46pin IC802 43pin RFGO 11 2 IC801 19pin IC802 49pin RFRP 15 3 IC801 17pin 3 FMO IC802 53pin STOP TEI PLAY TCD-782 TNO-02 PLAYBACK 16 1 IC802 46pin TRO SBAD LO 1 RO 2 IC802 85pin 2 IC802 49pin 7 FMO IC802 46pin IC802 44pin 11 2 CUE 1 FEI 6 TRO PLAY IC802 43pin 10 1 IC802 53pin STOP 5 TEI IC802 49pin IC802 46pin 5 PLAY IC802 46pin FEI 6 3 STOP IC802 43pin 9 2 DMO TOC IL IC802 57pin 8 SBOK IC802 55pin FOCUS SEARCH 7 1 IC802 12pin IC804 25pin 4 TMAX IC802 30pin IC802 48pin 2 PLAY 17 IC802 82pin 3 IC802 44pin – 36 – XL-60H/70H TROUBLESHOOTING When the CD does not function When the CD section does not operate when the objective lens of the optical pickup is dirty, this section may not operate. Clean the objective lens, and check the playback operation. When this section does not operate even after the above step is taken, check the following items. Remove the cabinet and follow the troubleshooting instructions. "Track skipping and/or no TOC (Table Of Contents) may be caused by build up of dust other foreign matter on the laser pickup lens. Before attempting any adjustment make certain that the lens is clean. If not, clean it as mentioned below." Turn the power off. Gently clean the lens with a lens cleaning tissue and a small amount of isopropyl alcohol. Do not touch the lens with the bare hand. Dust gradually accumulates on the objective lens during use, and it may degrade performance. To avoid this problem, use a cleaning disc designed for CD optical pickup lenses. HOW TO USE 1. Using the brush in the cleaner cap, apply 1 or 2 drops of the cleaning fluid to the brush on the CD cleaner disc which has the mark next to it. 2. Place the CD cleaner disc onto the CD disc tray with the brush side down, then press the play button. 3. You will hear music for about 20 seconds and the CD player will automatically stop. If it continues to turn, press the stop button. CAUTION The CD lens cleaner should be effective for 30~50 operations, however if the brushes become worn out earller then please replace the cleaner disc. If the CD cleaner brushes become very wet then wipe off any excess fluid with a soft cloth. Do not drink the cleaner fluid or allow it to come in contact with the eyes. In the event of this happening then drink and / or rinse with clean water and seek medical advice. The CD cleaner disc must not be used on car CD players or on computer CD ROM drives. All rights reserved. Unauthorized duplicating, broadcasting and renting this product is prohibited by law. Cleaner Liquid Cleaning Disc PARTS CODE: UDSKA0004AFZZ – 37 – XL-60H/70H Make sure that the disc is normal, and set the CD TEST MODE (STEP 1). Is the measured voltage as specified in circuit diagram? Check the main unit power supply circuit. No Yes Is "Er-CD01" displayed"? No Yes Move the pickup to most internal circumference side of disc. Turn the power off and reset the CD TEST MODE (STEP 1). Is "PU ERROR " not displayed? No Check the pattern between pin 57 (PUIN) of IC701 and BI803/ CNS803. Check the between BI803/CNS803 and PU-IN switch. Yes Is +5V applied to pin 100 (/RST) of IC802? No Check the PWB pattern between pin 45 (CD RES) of IC701 and pin 100 (/RST) of IC802. No Is CD Lid switch SW701 ON condition ? Yes Does the CD TEST MODE advance from "STEP 2"? Yes No Set ON condition the CD Lid switch. Yes Check the between pattern IC701 and SW701 If OK. Check the main unit power supply circuit. Does the laser come on in CD TEST MODE "STEP 2"? No Check the procedure in "LASER FAILURE". Yes Does the CD TEST MODE advance from "STEP 3" to "STEP 4"? Yes No Does the spindle motor rotate normally when the CD TEST MODE changes from "STEP 4" to "STEP 3"? No Check the procedure in "FOCUS FAILURE". Check the procedure in "SPINDLE MOTOR CLV SERVO FAILURE". Yes Is the HF output on pin 38 of IC802 in CD TEST MODE "STEP 5"? No Check the procedure "HF ERROR". Yes Does the sound heard when the optical pickup move to the selected play by the FF/REW key. No Does the sled motor move ? No Yes Check the procedure in "SLED MOTOR OPERATING FAILURE ". Yes Check the procedure "NO SOUND" Does the LCD track number and time indicator work properly ? No Check the pattern between IC701 and LCD701. Yes Turn the power off and then back on. Does the unit initialize properly and start playback when PLAY key is pressed? No Is "Er-CD01 " displayed ? No Is "Er-CD01" displayed? Yes Yes Check the pattern between pin 57 (PUIN) of IC701 and BI803/CNS803. Check the between BI803/CNS803 and PU-IN switch. Check the procedure in "HF ERROR". Does the unit play in order in the FF mode? No Check the procedure in "TRACK SEARCH FAILUR". Yes Does playback continue for 30 seconds after the start of playback ? No Yes Normal – 38 – Check the procedure in "SLED SERVO FAILURE". Yes XL-60H/70H • Laser failure. Is +6.2V applied to the emiter of Q861 ? No Check the PWB pattern between pin 16 of CNS602 and emiter of Q861. Yes Check the peripheral parts of IC804 and Q861. Is +5V applied to the collector of Q861 ? No Yes No Check the PWB pattern between collector of Q861 and pin 62 of IC802. No Check the PWB pattern between collector of Q861 and pin 1 of IC801. No Does the laser come on when pattern cut between pin 8 (SEL) of IC801 and pin 57 (SEL) of IC802 ? Is +5V applied to the pin 62 (VDD) of IC802 ? Yes Is +5V applied to the pin 1 (VCC) of IC801 ? Yes Is 0V applied to the pin 57 (SEL) of IC802 ? Yes Yes No Check the PWB pattern between IC701 and IC802 (BUCK/CCE/ BUS0~3) Is approx. 2V applied to the collector of Q801. No Check the peripheral parts of IC801 and Q801. If it is normal, the optical pickup is faulty. No Check as stated in item "FOCUS SERVO SAWTOOTH WAVE FAILURE". Yes Check BI802/CNS802. If it is normal, the optical pickup is faulty. • Focus failure. Does the optical pickup move up and down when the disc is removed? Yes Is the following waveform ouput at the pin 43 (FEI) of IC802 when the disc is set? Check the periphery of IC801 and BI802/CNS802. Is it normal? No Yes Yes pin 43 The optical pickup is faulty. (FEI) pin 48 (FOO) pin 44 (SBAD) Is the waveform shown above input at the pin 44 (SBAD) of IC802? No Yes IC801 is faulty. – 39 – Check the pattern between pin 13 of IC801 and pin 44 of IC802. Check the periphery of IC801 and BI802/CNS802. XL-60H/70H • Focus servo sawtooth wave failure. Is sawtooh wave output to the pin 48 (FOO) of IC802 ? No IC802 is faulty. Yes 1.5~2.5sec Check the PWB pattern between pin 16 of CNS602 and IC804. Is +6.2V applied to the pins 1 and 30 (VCC) of IC804 ? No Yes Is sawtooth wave obtained between pins 25 and 26 of IC804 ? No Yes Is +5V applied to the pin 2 (MUTE) of IC804 ? No Yes 1.5~2.5sec Check the PWB pattern between pin 2 of IC804 and pin 58 (CD STB) of IC701. Check the PWB pattern between pin 48 (FOO) of IC802 and pins 27 and 28 of IC804. If OK. IC804 is faulty. Is sawtooth wave obtained between pins 3 and 4 of BI801/ CNS801 ? (as shown above) Check the PWB pattern between BI801/CNS801 and IC804. No Yes BI801/CNS801 connection failure or optical pickup failure. • Spindle motor clv servo failure. Is following wave output to the pin 55 (DMO) of IC802 when the CD TEST MODE "STEP 3" is changed to " STEP 4" ? No Check the procedure in "HF ERROR". If OK. IC802 is faulty. No Check the PWB pattern between pin 55 (DMO) of IC802 and pins 5 and 6 of IC804. If OK. IC804 is faulty. Yes DMO Is above wave obtained between pins 5 and 6 of IC804 ? Yes Is above wave obtained between pins 5 and 6 of BI801/ CNS801 ? Check the PWB pattern between BI801/CNS801 and IC804. No Yes BI801/CNS801 connection failure or optical pickup failure. – 40 – XL-60H/70H • HF error. Is output (tracking error signal) obtained at the pins 46 (TEI) and 47 (TEZI) of IC802 the CD TEST MODE "STEP 4" is changed to "STEP 5"? No Is output obtained at the pins 2 and No 5 of BI802/CNS802 Optical pickup failure. Yes Yes test mode "step 4" Check the periphery of IC801. Check the PWB pattern between pin 12. (TEO) of IC801 and pins 46 and 47 of IC802. Is it normal ? test mode "step 5" TEI TEZI IC801 is faulty. No Yes Check the PWB pattern between pin 50 (TEO) of IC802 and pin 18 of IC804. Check the periphery of IC804 and BI801/CNS801. If OK. Optical pickup failure. Is output (HF signal) obtained at the pin 38 (RFI) of IC802 when the CD TEST MODE "STEP 4" is changed to "STEP 5"? No Optical pickup failure. Yes Yes test mode "step 4" test mode "step 5" Check the periphery of IC801. Check the PWB pattern between pin 19 (RFGO) of IC801 and pins 38 (RFI) of IC802. If OK. IC801 is faulty RFI Is output (HF signal) obtained at the pins 41 (RFZI) and 42 (RFRP) of IC802 when the CD TEST MODE "STEP 4" is changed to "STEP 5"? Yes Is output obtained at the pins 1 and 3, 4 of BI802/CNS802. No test mode "step 4" No Check the periphery of IC801. Check the PWB pattern between pin17 (RFRP) of IC801 and pins 41 (RFZI) and 42 (RFRP) of IC802. If OK. IC801 is faulty. test mode "step 5" RFZI RFRP Is the following wave output to the pin 55 (DMO) of IC802 when the CD TEST MODE "STEP 4" or "STEP 5"? Yes test mode "step 4" No Check the periphery pins 28~32 of IC802. If OK. IC802 failure. No Check the interval between the pins 82 or 85 of IC802 and the pins 1 or 3 IC601. test mode "step 5" DMO Normal. • No sound. No sound from both L and R-ch? Yes Check the PWB pattern between R819 and Q861. Is +4.5V applied to pin 83 (DVDD) of IC802? Yes No Is signal of pins 82 and 85 of IC802 output? Yes Check the peripheral parts of IC802. If OK, IC802 is faulty. No The main PWB is faulty. – 41 – XL-60H/70H • Track search failure Does the sled motor run in FF/REW state when the SERVO TEST MODE "STEP1" is set? No Check as stated in item "SLED MOTOR OPERATION FAILURE". Yes Is the following wave output to the pin 49 (TRO) of IC802 during track search in normal playback? No IC802 failure. Yes TRO Is the following wave output to the pins 12 (TEO) of IC801 during track search in normal playback? No Yes TEO TEI Check the PWB pattern between pin 49 (TRO) of IC802 and pin 18 of IC804. Check the PWB pattern between pins 20 and 21 of IC804 and Optical pickup. If OK. Optical pickup failure. TEZI Is the above wave output to the pins 46 (TEI) and 47 (TEZ) of IC802 during track serch in normal playback? No Check the PWB pattern between pin 12 (TEO) of IC801 and pins 46 and 47 of IC802. If OK. IC801 failure. No Check the PWB pattern between pin 17 (RFO) and 18 (RFIS), 19 (RFRP) of IC801 and pins 41 and 42 of IC802. If OK. IC801 failure. Yes Is the following wave output to the pin 41 (RFZI) and 42 (RFRP) of IC802 during track search in normal playback? Yes RFRP RFZI Normal. • Sled motor operation failure. Is following sled feed signal output the pin 53 (FMO) of IC802 when FF/REW key is pressed after the CD TEST MODE "STEP 1" is seted? Yes FF C801 is faulty. No REW FMO Is following sled feed signal output the pins 12 and 13 of IC804 when FF/REW key is pressed after the CD TEST MODE "STEP 1" is seted? FF Yes No Check the PWB pattern between pin 53 of IC802 and pins 12 and 13 of IC804. REW SL ± Is sled feed signal output the pins 10 and 11 of IC804? No Check the peripheral parts of IC804. If OK, IC804 is faulty. Yes Is sled feed voltage applied between both terminals of sled motor? Yes No Check the BI803/CNS803. Check the CD mechanism (periphery of sled motor). If the sled motor does not run when DC2.0V is applied to both terminals of sled motor, the sled motor is faulty. • Sled servo failure. Is following sled signal output the pin 53 (FMO) of IC802 during playback? IC802 is faulty. No Yes FMO Normal. – 42 – XL-60H/70H FUNCTION TABLE OF IC IC401 VHiLC75342M-1: Function/Volume Equalizer (LC75342M) Pin No. Port Name Function 1 DI Serial data and clock input pin for control. 2 CE Chip enable pin. Data written into an internal latch in a timing of [H] -> [L]. Each analog switch is activated. Data transfer enabled at [H] level. 3 VSS Ground pin. 4 TEST Electronic volume control pin. To be set to the VSS potential. 5 LOUT Volume + equalizer output pin. 6 LBASS2 Bass-band filter comprising capacitor and resistor connection pin. 7 LBASS1 Bass-band filter comprising capacitor and resistor connection pin. 8 LTRE Capacitor connection pin comprising treble band filter. 9 LIN Volume + equalizer input pin. 10 LSEL0 Input selector output pin. 11 L4 Input signal pin. 12 L3 Input signal pin. 13 L2 Input signal pin. 14 L1 Input signal pin. 15* NC No CONNECT pin. To be open or connected to VSS. 16* NC No CONNECT pin. To be open or connected to VSS. 17 R1 Input signal pin. 18 R2 Input signal pin. 19 R3 Input signal pin. 20 R4 Input signal pin. 21 RSEL0 Input selector output pin. 22 RIN Volume + equalizer input pin. 23 RTRE Capacitor connection pin comprising treble band filter. 24 RBASS1 Bass-band filter comprising capacitor and resistor connection pin. 25 RBASS2 Bass-band filter comprising capacitor and resistor connection pin. 26 ROUT Volume + equalizer output pin. 27* NC No CONNECT pin. To be open or connected to VSS. 28 Vref 0.5 x VDD voltage generation block for analog ground. Capacitor of several 10µF to be connected between Vref and AWSS (VSS) as a counter measure against power ripple. 29 VDD Supply pin. 30 CL Serial data and clock input pin for control. In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. – 43 – XL-60H/70H IC401 VHiLC75342M-1: Function/Volume Equalizer (LC75342M) TEST VSS CE 4 3 2 DI CL VDD Vref NC 1 30 29 27 28 LOUT 5 CONTROL CIRCUIT LBASS1 7 LTRE 8 RVref 25 RBASS2 24 RBASS1 CONTROL CIRCUIT LBASS2 6 LOGIC CIRCUIT CCB INTERFACE LVref 26 ROUT 23 RTRE 22 RIN LIN 9 21 RSEL0 LSEL0 10 11 12 13 14 15 16 17 18 19 20 L4 L3 L2 L1 NC NC R1 R2 R3 R4 Figure 44 BLOCK DIAGRAM OF IC – 44 – XL-60H/70H IC701 RH-iX0026SJZZ: System Control Microcomputer (IX0026SJ) (1/2) Pin No. Terminal Name Input/Output 1-4 COM3-COM0 5-7 VLC3-VLC1 — LCD power supply terminal. 8 VDD — Microcomputer power supply +5V. Output Function LCD common output terminal. 9 OSC2 Output Oscillator ground terminal for main clock. f=8MHz 10 OSC1 Input Oscillator ground terminal for main clock. f=8MHz 11 VSS 12 XI Input Oscillator ground terminal for sub clock. f=32.768kHz 13 XO Output Oscillator ground terminal for sub clock. f=32.768kHz 14 MMOD Input 15 VREF- — 16 KEY0 AN0/PA0 Input CD lid status detection input. 17 KEY1 AN0/PA1 Input Operation button input, Max-8 buttons. 18 KEY2 AN0/PA2 Input Operation button input, Max-8 buttons. 19 KEY3 AN0/PA3 Input MODEL/TUNER destination input. 20 KEY4 AN0/PA4 Input Current detection of CD lid control motor. Used to decide the CD lid drive error to control it. — Microcomputer power supply GND. Memory mode selection terminal. Power supply GND for AD converter. 21* KEY5 AN0/PA5 Input CD servo auto adjustment mode selection input. 22 KEY6 AN0/PA6 Input Tape mechanism operating status detection input. Decides the F.P/CAM-SW status with A/D value. 23 KEY7 AN7/PA7 Input 24 VREF+ 25 TXD SBO0/P00 Output 26 RXD SBI0/P01 Input 27 SBT0/P02 Output Synchronous clock output with TUNER PLL IC 28 SBO1/P03 Output Enable output of TUNER PLL IC. "L" = OFF "H" = ON 29 SBI1/P04 Output Tape mechanism solenoid drive control output. 30 SBT1/P05 Output Tape mechanism motor drive control output. 31 DK/BZER P06 Output Recording/playback selection output of tape circuit. "H" = Recording mode, "L" = Playback mode 32 RST/P27 Input Reset signal input 33 RMOUT P10 Input CLOCK/TIMER/SLEEP button input. 34 P11 Input Tape run/END detection input. Decided as tape run if pulse is input. 35 TM2IO P12 Output 36* TM3IO P13 Output 37 TM4IO P14 Input 38 IRQ0 P20 Input Switches to the HALT mode when changing to . "L" at power failure detection input. 39 SENS IRQ1/P21 Input Remote control signal input. 40 IRQ2 P22 Input Synchronous clock input with RDS IC. 41 IRQ3 P23 Input Jog dial UP pulse input. 42 IRQ4 P24 Input Jog dial DOWN pulse input. 43 P30 Output SURROUND control output. 44 P31 Output POWER IC STAND-BY terminal CONTROL. 45 P32 Output Power mute output. "H" = MUTE ON "L" = MUTE OFF 46 LED0 WE/P50 Output CD servo power supply circuit control output. "H" = CD power ON "L" = CD power OFF 47 LED1 RE/P51 Output Main TRANS RELAY CONTROL. "H" = ON "L" = OFF 48 LED2 CS/P52 Input Data input from RDS IC. 49 LDE3/S51 A16/P53 Input Radio stereo broadcast reception detection input. "L" = During stereo broadcast reception 50 LED4/S50 A17/P54 Input Broadcast reception status detection input. "L" = During broadcasting signal reception 51 SEG49 P60/A0 — Output 52* SEG48 P61/A1 Output 53 SEG47 P62/A2 Output Tuner signal meter (S meter) voltage input terminal. Power supply for A/D converter +5V. Data output terminal to TUNER PLL IC. Data input from TUNER PLL IC Recording bias oscillation circuit control output. "H" = Bias oscillation, "L" = oscillation stop. Recording bias oscillation frequency selection control output. Power (POWER) button input detection. LCD backlight control signal output. "H" = Backlight ON, "L" = Backlight OFF LED illumination control of electric JOG dial. "H" = ON "L" = OFF In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. – 45 – XL-60H/70H IC701 RH-iX0026SJZZ: System Control Microcomputer (IX0026SJ) (2/2) Pin No. Terminal Name Input/Output Function 54 SEG46 P63/A3 Output Electric JOG dial UP. 55 SEG45 P64/A4 Output Electric JOG dial DOWN. 56 SEG44 P65/A5 Output Electric CD lid OPEN. 57 SEG43 P66/A6 Output 58 SEG42 P67/A7 Input 59 SEG41 P70/A8 Output Reset signal output for TC9462F 60 SEG40 P71/A9 Output ON/OFF output terminal of CD servo control IC. "H" = Servo ON "L" = Servo stand-by 61-64 SEG39 P72/A10- Input/Output SEG36 P75/A13 65 SEG35 P76/A14 Output Data synchronous clock output for TC9462F. 66 SEG34 P77/A15 Output Chip enable terminal for TC9462F. "L" = BUS terminal active 67 SEG33 P87/D7 — 68 SEG32 P86/D6 — LCD segment output. 69-74 SEG31 P85/D5SEG26 P80/D0 — LCD segment output Note: Since RH-******SJZZ, SEG0 of the LCD is connected by the 24-pin LCD to SEG7 of the microcomputer output terminal, and connections are made up to the shift SEG26 in order. 75-100 SEG25-SEG0 — LCD segment output Note: Since RH-******SJZZ, SEG0 of the LCD is connected by the 24-pin LCD to SEG7 of the microcomputer output terminal, and connections are made up to the shift SEG26 in order. Electric CD lid CLOSE. CD pickup position detection SW input. "L" = Innerst periphery Data input/output terminal for TC9462F control. LCD segment output. 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 S S S S S S S S S S S S S S S S S S S S S S S S S SEG0 SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24 IC701 RH-iX0026SJZZ: System Control Microcomputer (IX0026SJ) I O I I I I I I I I I O 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 O I 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 I O O O O O I I I O O I I I I I I O O O O O O O I O O O O DO CL CE SOL MOT REC RESET CLOCK RUN_PLS BIAS B-CAN POWER SYS STOP REMOCON CLE JOG UP JOG DOWN SURR P-STB P-MUTE CD+B P-CONT DATA STEREO SD COM3 COM2 COM1 COM0 VLC3 VLC2 VLC1 VDD OSC2 OSC1 VSS XI XO MMOD VREFCLID_SW KEY1 KEY2 MODEL CLID_PRO CD_CONF TAPE_SW VSM VREF+ DI Figure 46 BLOCK DIAGRAM OF IC – 46 – S S S S S S S S S O O I/O I/O I/O I/O O O I O O O O O SEG25 SEG26 SEG27 SEG28 SEG29 SEG30 SEG31 SEG32 SEG33 CCE BUCK BUS3 BUS2 BUS1 BUS0 CD_STB CD_RES PU-IN CLID_DW CLID_UP MVOL_DW MVOL_UP MVOL_IND O B-LIGHT XL-60H/70H IC801 VHiTA2109F/-1:Servo Pre Amp. (TA2109F) Pin No. Terminal Name Function Input/Output 1 VCC — 2 FNI Input Main beam amp input terminal 3 FPI Input Main beam amp input terminal 4 TPI Input Sub-beam amp input terminal 5 TNI Input Sub-beam amp input terminal 6 MDI Input Monitor photodiode amp input terminal 7 LDO Output 8 SEL Input Laser diode control signal input and APC circuit ON/OFF signal input terminal 9 TEB Input Tracking error balance adjustment signal input terminal To be controlled by 3-value PWM signal. (PWM carrier = 88.2 kHz) 10 2VRO 11 TEN Input 12 TEO Output 13 SBAD Output Sub-beam addition signal output terminal 14 FEO Output Focus error signal generation amp output terminal 15 FEN Input 16 VRO Output Standard voltage (VR) output terminal. When Vcc = 5V, VR = 2.1V. 17 RFRP Output Track count signal generation amp output terminal 18 RFIS Input 19 RFGO Output 20 RFGC Input RF amplitude adjustment control signal input terminal The amplitude of RF signal can be controlled by using the 3-value PWM signal (PWM carrier = 88.2 kHz) which is output from the RFGC terminal of TC9432F. 21 AGCI Input RF signal amplitude adjustment amp input terminal 22 RFO Output 23 GND — 24 RFN Input Output Power voltage terminal Laser diode amp output terminal Standard voltage (2VR) output terminal. When Vcc = 5V, 2VR = 4.2V. Tracking error signal generation amp reversed phase input terminal Tracking error signal generation amp output terminal Focus error signal generation amp reversed phase input terminal RFRP detection circuit input terminal RF signal output terminal RF signal generation amp output terminal GND terminal RF reversed phase input terminal IC801 VHiTA2109F/-1:Servo Pre Amp. (TA2109F) 15kΩ 15kΩ SBAD 13 7.67kΩ 12 TEO 30kΩ 20µA 50kΩ 10pF 20pF 10kΩ 10kΩ 36pF 21kΩ 29kΩ 24kΩ 24kΩ 11 TEN 7.96kΩ 10 2VRO 10kΩ VRO 16 21kΩ RFRP 17 20kΩ 50µA 47kΩ SW1 12kΩ LDC 1kΩ SW2 65µA SW3 PEAK BOTTOM RFGO 19 8 SEL 1.74kΩ 20kΩ 20kΩ 9 TEB 3 STATE DET. 21kΩ 12kΩ RFIS 18 SEL 10kΩ FEO 14 FEN 15 30kΩ 10kΩ 7 LDO 680kΩ 180kΩ 13kΩ 20pF RFGC 20 2.12kΩ 6 MDI I.I 5 TNI I.I 4 TPI 180kΩ 12kΩ AGCI 21 20pF 23.5kΩ re = 130Ω 20kΩ 180kΩ RFO 22 40pF 20kΩ 60kΩ 3 FPI 20kΩ 2 FNI 40pF 20kΩ 1 VCC 3.3kΩ 3.3kΩ RFN 24 1.53kΩ 180kΩ 60kΩ GND 23 Figure 47 BLOCK DIAGRAM OF IC – 47 – L HiZ H LDC SW1 SW2 ON OFF OFF ON OFF ON SW3 OFF ON ON XL-60H/70H IC802 VHiTC9462F/-1: Servo/Signal Control (TC9462F) (1/3) Pin No. Port Name Function Input/Output 1* TEST0 Input Test mode terminal. To be opened usually. 2* 3* /HSO /UHSO Output Output Playback speed mode flag output terminal. /UHSO /HSO Playback speed H H x1 speed playback H L x2 speed playback L H x4 speed playback L L — 4* EMPH Output Sub-code Q data emphasis flag output terminal. "H": Emphasis ON "L": Emphasis OFF The output polarity can be inverted by command. 5* LRCK Output Channel clock (44.1 kHz) output terminal. "L": L channel "H": R channel The output polarity can be inverted by command. 6 VSS — 7* BCK Output Bit clock (1.4122 MHz) output terminal. 8* AOUT Output Audio data output terminal. 9 DOUT Output Digital out output terminal. 10* MBOV Output Buffer memory over signal output terminal. "H": Over 11* IPF Output Correction flag output terminal. "H": When AOUT output is correction-disabled symbol in case of C2 correction output. 12* SBOK Output Sub-code Q data CRCC judgment result output terminal. "H": When judgment result is OK. 13* CLCK Input/Output 14 VDD — Digital + power terminal. 15 VSS — Digital ground terminal. 16* DATA Output Sub-code P-W data output terminal. 17* SFSY Output Playback system frame sync signal output terminal. 18* SBSY Output Sub-code block sync output terminal. "H": On S1 position when the sub-code sync is detected. 19* SPCK Output Processor status signal read clock (176.4 kHz) output terminal. 20* SPDA Output Processor status signal output terminal. 21* COFS Output Correction system frame clock (7.35 kHz) output terminal. 22* MONIT Output LSI internal signal monitor terminal. It is possible to monitor the DSP internal flag and PLL system clock with the microcomputer command. Terminal for serial output of text data according to command . 23 VDD 24 TESIO0 — Input — Digital ground terminal. Sub-code P-W data read clock output/input terminal. Selectable with command bit. Digital + power terminal. Test input/output terminal. To be fixed to "L" usually. Terminal to input the text data read clock according to command. 25 P2VREF 26* HSSW 27* ZDET Output 1-bit DAC zero detection flag output terminal. 28 PDO Output Terminal to output the phase difference between EFM signal and PLCK signal. 29* TMAXS Output TMAX detection result output terminal. To be selected with command bit TMPS. 30 TMAX Output TMAX detection result output terminal. To be selected with command bit TMPS. Output 2VREF terminal for PLL system. VREF voltage in case of x2 speed/x4 speed. TMAX detection result 31 LPFN Input 32 LPFO Output 33 PVREF 34 VCOREF 35 VCOF Output 36 AVSS — 37 SLCO Output 38 RFI — Input Input TMAX output Longer than specific period "P2VREF" Shorter than specific period "VSS" Within specific period "HIZ" Low-pass filter amp inverted input terminal. Low-pass filter amp output terminal. VREF terminal for PLL system. VCO center frequency standard level terminal. To be fixed to PVref usually. VCO filter terminal. Analog system ground terminal. Data slice level generation DAC output terminal. RF signal input terminal. In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. – 48 – XL-60H/70H IC802 VHiTC9462F/-1: Servo/Signal Control (TC9462F) (2/3) Pin No. Port Name Function Input/Output 39 AVDD — 40 RFCT Input RFRP signal center level input terminal. 41 RFZI Input RFRP zero cross input terminal. 42 RFIP Input RF ripple signal input terminal. 43 FEI Input Focus error signal input terminal. 44 SBAD Input Sub-beam addition signal input terminal. 45 TSIN Input Test input terminal. To be fixed to Vref usually. 46 TEI Input Tacking error input terminal. (Tracking servo ON: Taking-in). 47 TEZI Input 48 FOO Output Focus equalizer output terminal. 49 TRO Output Tracking equalizer output terminal. 50 VREF — 51 RFGC Output RF amplitude adjustment control signal output terminal. 3-value PWM signal is output. (PWM carrier = 88.2 kHz) 52 TEBC Output Tracking balance control signal output terminal. 3-value PWM signal is output. (PWM carrier = 88.2 kHz) 53 FMO Output Feed equalizer output terminal. 3-value PWM signal is output. (PWM carrier = 88.2 kHz) 54* FVO Output Speed error signal or feed search EQ output terminal. 3-value PWM signal is output. (PWM carrier = 88.2 kHz) 55 DMO Output Disc equalizer output terminal. 3-value PWM signal is output. (PWM carrier = DSP system 88.2 kHz, sync with PXO) 56 2VREF 57 SEL Output APC circuit ON/OFF signal output terminal. When laser is ON and UHS = L, "Hi-Z". When UHS = H, "H" output is obtained. 58* FLGA Output Internal signal monitor external flag output terminal. TEZC, FOON, FOK and RFZC signals can be selected with command. 59* FLGB Output Internal signal monitor external flag output terminal. DFCT, FOON, FMON and RFZC signals can be selected with command. 60* FLGC Output Internal signal monitor external flag output terminal. TRON, TRSR, FOK, and SRCH signals can be selected with command. 61* FLGD Output Internal signal monitor external flag output terminal. TRON, DMON, HYS and SHC signals can be selected with command. 62 VDD — — Analog system power terminal. Tracking error, zero cross input termina.l Analog standard power terminal. Analog standard power terminal (2xVREF) Digital + power terminal. 63 VSS — 64* 65* 66* 67* IO0 IO1 IO2 IO3 Input/Output 68* /DMOUT Input Terminal to set the mode to output 2-value PWM of feed equalizer from IO0,1 terminal and 2value PWM of disc equalizer from IO2,3 terminal. "L" active 69* /CKSE Input To be opened usually. 70* /DACT Input DAC test mode terminal. To be opened usually. 71 TESIN Input Test input terminal (externally provided VCO clock input terminal). To be fixed to "L" usually. 72 TESIO1 Input Test input/output terminal. To be fixed to "L" usually. 73 VSS — 74 PXI Input 75* PXO Output 76 VDD — Digital + power terminal. 77 XVSS — System clock oscillation circuit ground terminal. 78 XI Input 79 XO Output 80 XVDD — System clock oscillation circuit + power terminal. 81 DVSR — R channel D/A converting section power terminal. 82 RO Output Digital ground terminal. General-use I/O port. The input port and output port can be selected with command. In case of input port the terminal state (H/L) can be read with the read command. In case of output port the terminal state (H/L/HiZ) can be controlled with command. Digital ground terminal. DSP system clock oscillation circuit input terminal. To be fixed to "L" usually. DSP system clock oscillation circuit output terminal. System clock oscillation input terminal. System clock oscillation circuit output terminal. R channel data forward rotation output terminal. In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. – 49 – XL-60H/70H IC802 VHiTC9462F/-1: Servo/Signal Control (TC9462F) (3/3) Function Input/Output Port Name Pin No. 83 DVDD — D/A converting section power terminal. 84 DVR — Reference voltage terminal. 85 LO Output L channel data forward rotation output terminal. 86 DVSL — 87* TEST1 Input L channel D/A converting section power terminal. Test mode terminal. To be opened usually. 88* TEST2 Input Test mode terminal. To be opened usually. 89* TEST3 90-93 BUS0-BUS3 94 VDD — Digital + power terminal. 95 VSS — Digital ground terminal. 96 BUCK Input Microcomputer interface clock input terminal. 97 /CCE Input Microcomputer interface chip enable signal input terminal. "L": BUS0 to 3 is active. 98* TEST4 Input Test mode termina. To be opened usually. Input Test mode terminal. To be opened usually. Input/Output Microcomputer interface data input/output terminal. 99* /TSMOD Input Local test mode selection terminal. 100 /RST Input Reset signal input terminal. "L": Reset. In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. Figure 50 BLOCK DIAGRAM OF IC – 50 – XO 79 XVDD 80 99 100 98 97 /CCE 96 BUCK 95 VSS 94 VDD 93 BUS3 92 BUS2 91 BUS1 90 BUS0 89 TEST3 88 TEST2 87 TEST1 86 DVSL 85 LO 84 DVR 83 LPF XI 78 XVSS 77 PXI 74 VSS 73 TESIN 71 TESIO1 72 /DACT 70 /CKSE 69 /DMOUT 68 IO3 67 IO2 66 IO1 65 IO0 64 VSS 63 VDD 62 FLGD 61 FLGC 60 FLGB 59 SEL 57 PWM VDD 76 1Bit DAC PXO 75 D/A Microcomputer interface ROM Address circuit TEST4 DVDD 82 Synchronizing signal guarantee EFM demodulation RAM Correction circuit /RST RO 81 1 TEST0 2 /HSO 3 /UHSO 4 EMPH 5 LRCK 6 VSS 7 BCK 8 AOUT 9 DOUT 10 MBOV 11 IPF 12 SBOK 13 CLCK 14 VDD 16 DATA 15 VSS 17 SFSY 18 SBSY 19 SPCK 20 SPDA 21 COFS 22 MONIT 23 VDD 25 P2VREF 24 TESIO0 Digital equalizer adjustment circuit FLGA 58 VREF 16KRAM Servo control 2VREF 56 TRO Audio output circuit Clock generator FVO 54 FOO CLV servo A/D DMO 55 TEZI Data slicer FMO 53 TEI Digital out VCO TEBC 52 TSIN Sub-code demodulation circuit Status RFGC 51 SBAD 26 HSSW 27 ZDET 28 PDO PLL TMAX 31 32 34 35 36 37 38 41 FEI 49 RFRP 50 RFZI 42 RFCT 43 AVDD 44 RFI 45 SLCO 46 AVSS 47 VCOF 48 VCOREF 39 PVREF 40 LPFO 33 LPFN 29 TMAXS 30 TMAX IC802 VHiTC9462F/-1: Servo/Signal Control (TC9462F) DVSR /TSMOD XL-60H/70H IC804 VHiLA6541D/-1: Focus/Tracking/Spin/Sled Driver (LA6541D) Pin No. Port Name Function 1 VCC Power (short-circuited to pin 30) 2 MUTE All BTL AMP output ON/OFF 3 VIN1 BTL AMP1 input terminal 4 VG1 BTL AMP1 input terminal (for gain adjustment) 5 VO1 BTL AMP1 output terminal (noninversion side) 6 VO2 BTL AMP1 output terminal (inversion side) 7 GND GND terminal (lowest potential) 8 GND GND terminal (lowest potential) 9 GND GND terminal (lowest potential) 10 VO3 Output terminal of BTL AMP2 (inversion side) 11 VO4 Output terminal of BTL AMP2 (noninversion side) 12 VG2 Input terminal of BTL AMP2 (for gain adjustment) 13 VIN2 Input terminal of BTL AMP2 14 REG OUT Connect the collector of externally provided transistor (PNP). 5V power output 15 REG IN Connect the base of externally provided transistor (PNP). 16* RES Reset output 17* CD Reset output delay time setting (capacitor provided externally) 18 VIN3 Input terminal of BTL AMP3 19* VG3 Input terminal of BTL AMP3 (for gain adjustment) 20 VO5 Output terminal of BTL AMP3 (noninversion side) 21 VO6 Output terminal of BTL AMP3 (inversion side) 22 GND GND terminal (lowest potential) 23 GND GND terminal (lowest potential) 24 GND GND terminal (lowest potential) 25 VO7 Output terminal of BTL AMP4 (inversion side) 26 VO8 Output terminal of BTL AMP4 (noninversion side) 27 VG4 Input terminal of BTL AMP4 (for gain adjustment) 28 VIN4 Input terminal of BTL AMP4 29 VREF Application of standard voltage of level shift circuit 30 VCC Power (short-circuited to pin 1) *GND (lowest potential) is connected to the frame of pin center. In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. VCC Vref VIN4 VG4 Vo8 Vo7 GND GND GND Vo6 Vo5 VG3 VIN3 CD RES IC804 VHiLA6541D/-1: Focus/Tracking/Spin/Sled Driver (LA6541D) 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 Vcc 11kΩ 11kΩ Level shift 4 BTL AMP 4 BTL AMP 3 Level shift 3 RESET Level shift 1 BTL AMP 1 BTL AMP 2 Level shift 2 Regulator 11kΩ 10 11 12 13 14 15 Reg OUT Reg IN Vo1 9 VIN2 VG1 8 VG2 VIN1 7 Vo4 Mute 6 Vo3 5 GND 4 GND 3 GND 2 Vo2 1 VCC 11kΩ Figure 51 BLOCK DIAGRAM OF IC – 51 – XL-60H/70H LCD701: RV-LX0007SJZZ LCD Display z1 z4 z2 r z3 q 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 PinNo com1 1 com1 2 com2 com3 PinNo com1 com2 com3 com4 22 h5 j5 l5 k5 23 g5 n5 m5 d5 24 a5 p5 f5 e5 com4 25 RDS b6 c6 ST com4 com2 3 com3 4 5 z1 b1 c1 z2 26 h6 j6 l6 k6 6 h1 j1 l1 k1 27 g6 n6 m6 d6 7 g1 n1 m1 d1 28 a6 p6 f6 e6 8 a1 p1 f1 e1 29 r b7 c7 q 9 REC b2 c2 z3 30 h7 j7 l7 k7 10 h2 j2 l2 k2 31 g7 n7 m7 d7 11 g2 n2 m2 d2 32 a7 p7 f7 e7 12 a2 p2 f2 e2 33 TP b8 c8 13 SLEEP b3 c3 MHz 34 h8 j8 l8 k8 14 h3 j3 l3 k3 35 g8 n8 m8 d8 15 g3 n3 m3 d3 36 a8 p8 f8 e8 16 a3 p3 f3 e3 37 EON PTY TI TA 17 RANDOM b4 c4 kHz 38 SRS(0) 18 h4 j4 l4 k4 39 com4 19 g4 n4 m4 d4 40 20 a4 p4 f4 e4 41 21 MEMORY b5 c5 z4 42 Figure 52 LCD SEGMENT – 52 – com3 com2 com1 XL-60H/70H PARTS GUIDE MODEL XL-60H XL-70H XL-60H/XL-70H Micro Component System consisting of XL-60H/ XL-70H (main unit) and CP-XL60H/CP-XL70H (speaker system). “HOW TO ORDER REPLACEMENT PARTS” To have your order filled promptly and correctly, please furnish the following information. 1. MODEL NUMBER 2. REF. No. 3. PART NO. 4. DESCRIPTION For U.S.A. only Contact your nearest SHARP Parts Distributor to order. For location of SHARP Parts Distributor, Please call Toll-Free; 1-800-BE-SHARP MARK: SPARE PARTS-DELIVERY SECTION Explanation of capacitors/resistors parts codes Capacitors Resistors VCC ....................... Ceramic type VCK ........................ Ceramic type VCT ........................ Semiconductor type VC • • MF ............... Cylindrical type (without lead wire) VC • • MN ............... Cylindrical type (without lead wire) VC • • TV ................ Square type (without lead wire) VC • • TQ ............... Square type (without lead wire) VC • • CY ............... Square type (without lead wire) VC • • CZ ............... Square type (without lead wire) VC • • • • • • • • • J .. The 13th character represents capacity difference. ("J" ±5%, "K" ±10%, "M" ±20%, "N" ±30%, "C" ±0.25 pF, "D" ±0.5 pF, "Z" +80-20%.) VRD ....................... Carbon-film type VRS ........................ Carbon-film type VRN ....................... Metal-film type VR • • MF ............... Cylindrical type (without lead wire) VR • • MN ............... Cylindrical type (without lead wire) VR • • TV ................ Square type (without lead wire) VR • • TQ ............... Square type (without lead wire) VR • • CY ............... Square type (without lead wire) VR • • CZ ............... Square type (without lead wire) VR • • • • • • • • • J .. The 13th character represents error. ("J" ±5%, "F" ±1%, "D" ±0.5%.) If there are no indications for the electrolytic capacitors, error is ±20%. If there are no indications for other parts, the resistors are ±5% carbon-film type. NOTE: Parts marked with “ ” are important for maintaining the safety of the set. Be sure to replace parts with specified ones for maintaining the safety and performance of the set. XL-60H/70H NO. PRICE RANK PARTS CODE DESCRIPTION NO. ZD601 ZD602 ZD681 ZD682 ZD701 XL-60H/70H INTEGRATED CIRCUITS IC101 IC102 VHIBA3126N/-1 VHIBA3311L/-1 J J IC201 IC302 IC303 VHIKIA4558P-1 VHILC72131/-1 VHILA1832S/-1 J J J IC401 VHILC75342M-1 J IC521 IC601 IC701 VHILC72723M-1 VHILA4451//-1 RH-IX0026SJZZ J J J IC702 IC801 IC802 IC804 VHITA7291S/-1 VHITA2109F/-1 VHITC9462F/-1 VHILA6541D/-1 J J J J IC805 VHITA7291S/-1 J AF Head Selector,BA3126N AK REC./P.B.Equalizer Amp., BA3311L AC Surround Control,KIA4558P AP PLL (Tuner),LC72131 AN FM IF Det./FM Mpx./AM IF, LA1832S AN Function/Volume Equalizer,LC75342M AS RDS Circuit,LC72723M AN Power Amp.,LA4451 AX System Control Microcomputer, IX0026SJ AH Loading Motor Driver,TA7291S AL Servo Pre Amp.,TA2109F AZ Servo/Signal Control,TC9462F AW Focus/Tracking/Spin/Sled Driver, LA6541D AH CD Motor Driver,TA7291S J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AB AD AB AC AC AC AB AC AC AC AB AB AB AF AB AF AC AC AD AB AC AB AC AB AC AB AD AC AD AC AC AD AC TRANSISTORS Q101~106 Q151 Q152 Q153 Q171 Q172 Q201 Q203 Q301 Q351 Q360 Q521 Q601~603 Q604,605 Q606 Q607 Q608 Q609 Q681,682 Q683 Q701 Q702,703 Q706 Q707,708 Q709 Q801 Q861 Q901 Q902 Q903 Q904 Q905 Q906 VSKTC3199GR-1 VS2SC2001-K-1 VSKTA1266GR-1 VSKRC104M//-1 VSKRA102M//-1 VSKRC102M//-1 VS2SK246GR/-1 VSKRC107M//-1 VS2SC380-O/-1 VSKRC104M//-1 VSKTA1266GR-1 VSKTC3199GR-1 VSKTC3199GR-1 VS2SD2012Y/-1 VSKTC3199GR-1 VS2SD2012Y/-1 VSKRA102M//-1 VSKRC107M//-1 VS2SD468-C/-1 VSKTC3199GR-1 VSKRC102M//-1 VSKTC3199GR-1 VSKRC102M//-1 VSKTA1266GR-1 VSKRC102M//-1 VSKTA1266GR-1 VS2SB562-C/-1 VSKRC102M//-1 VS2SB562-C/-1 VSKRC107M//-1 VSKRC102M//-1 VS2SB562-C/-1 VSKRA102M//-1 Silicon,NPN,KTC3199 GR Silicon,NPN,2SC2001 K Silicon,PNP,KTA1266 GR Digital,NPN,KRC104 M Digital,PNP,KRA102 M Digital,NPN,KRC102 M FET,2SK246 GR Digital,NPN,KRC107 M Silicon,NPN,2SC380 O Digital,NPN,KRC104 M Silicon,PNP,KTA1266 GR Silicon,NPN,KTC3199 GR Silicon,NPN,KTC3199 GR Silicon,NPN,2SD2012 Y Silicon,NPN,KTC3199 GR Silicon,NPN,2SD2012 Y Digital,PNP,KRA102 M Digital,NPN,KRC107 M Silicon,NPN,2SD468 C Silicon,NPN,KTC3199 GR Digital,NPN,KRC102 M Silicon,NPN,KTC3199 GR Digital,NPN,KRC102 M Silicon,PNP,KTA1266 GR Digital,NPN,KRC102 M Silicon,PNP,KTA1266 GR Silicon,PNP,2SB562 C Digital,NPN,KRC102 M Silicon,PNP,2SB562 C Digital,NPN,KRC107 M Digital,NPN,KRC102 M Silicon,PNP,2SB562 C Digital,PNP,KRA102 M DIODES ! ! D104 D201 D301~304 D401~403 D521,522 D601~604 D611~614 D651~654 D656~659 D681~684 D685 D701~709 D720~723 D730 D732 D736,737 D901~904 ZD351 VHD1N4148//-1 VHD1N4148//-1 VHD1N4148//-1 VHD1N4004//-1 VHD1N4148//-1 VHD1N4148//-1 VHD1N4004//-1 VHD1N5402M/-1 VHD1N4004//-1 VHD1N4004//-1 VHD1N4004//-1 VHPMPG3372X-V VHD1N4148//-1 VHPHY2043//-1 VHPHY2043//-1 VHPHY2043//-1 VHD1N4148//-1 VHEMTZJ5R1B-1 J J J J J J J J J J J J J J J J J J AA AA AA AB AA AA AB AE AB AB AB AD AA AD AD AD AA AC Silicon,1N4148 Silicon,1N4148 Silicon,1N4148 Silicon,1N4004 Silicon,1N4148 Silicon,1N4148 Silicon,1N4004 Silicon,1N5402M Silicon,1N4004 Silicon,1N4004 Silicon,1N4004 LED,Green,MPG3372X Silicon,1N4148 LED,Orange,HY2043 LED,Orange,HY2043 LED,Orange,HY2043 Silicon,1N4148 Zener,5.1V,MTZJ5.1B PRICE RANK PARTS CODE DESCRIPTION VHEMTZJ130A-1 VHEMTZJ7R5C-1 VHEMTZJ6R8A-1 VHEMTZJ5R6B-1 VHEMTZJ3R3B-1 J J J J J AC AC AA AD AA Zener,13V,MTZJ13A Zener,7.5V,MTZJ7.5C Zener,6.8V,MTZJ6.8A Zener,5.6V,MTZJ5.6B Zener,3.3V,MTZJ3.3B RFILF0072AFZZ RFILF0003AWZZ RFILL0001AWZZ RCILZ0002SJZZ J J J J AG AK AE AG FM IF FM IF Low Pass Filter Line Filter RFILA0003SJZZ RCILI0004SJZZ RTRNP0043SJZZ RTRNP0025SJZZ J J J J AF AF BA AU AM IF AM IF Power,Main Power,Sub VP-MK331K0000 RBLN-0001AWZZ VP-DH2R2K0000 VP-DH101K0000 VP-DH102K0000 VP-DH2R2K0000 RCILZ0001SJZZ VP-DH100K0000 VP-DH101K0000 VP-DH100K0000 VP-XHR82K0000 VP-DH100K0000 VP-DH2R2K0000 RCILA0007SJZZ RCILB0009SJZZ J J J J J J J J J J J J J J J AB AD AB AB AB AB AD AB AB AB AC AB AB AG AG 330 µH,Choke Balun 2.2 mmH,Peaking 100 µH,Choke 1 mH,Choke 2.2 mmH,Peaking 0.3 mH,Coil 10 µH,Choke 100 µH,Choke 10 µH,Choke 0.82 µH 10 µH,Choke 2.2 mmH,Peaking AM Antenna AM Oscillation J AB 10 kohm (B),Semi-VR [FM Mute Level] J AK Variable Capacitance,SVC348S J J J J J J AG AF AF AG AC AL Ceramic,456 kHz Crystal,4.5 MHz Crystal,456 kHz Ceramic,8 MHz Crystal,32.768 kHz Crystal,16.93 MHz J J J J J J J J J J J J J J J J J J J J J AA AA AA AB AB AB AB AA AB AA AB AB AB AB AA AB AB AB AA AB AB 0.001 µF,50V 330 pF,50V 270 pF,50V 47 µF,16V,Electrolytic 0.015 µF,50V,Mylar 10 µF,16V,Electrolytic 4.7 µF,25V,Electrolytic 0.0022 µF,50V 10 µF,16V,Electrolytic 82 pF,50V 2.2 µF,50V,Electrolytic 100 µF,25V,Electrolytic 22 µF,16V,Electrolytic 4.7 µF,25V,Electrolytic 820 pF,50V 0.0039 µF,100V,Polypropylene 0.027 µF,50V,Mylar 100 µF,16V,Electrolytic 0.0056 µF,50V 1 µF,50V,Electrolytic 100 µF,16V,Electrolytic FILTERS ! CF301,302 CF351 L354 LF651 TRANSFORMERS ! ! CF352 T351 T651 T681 COILS L151 L341 L342 L351,352 L353 L521 L601,602 L603 L701 L801 L802 L803 L804 T302 T306 VARIABLE RESISTOR VR351 RVR-M0999AFZZ VARIABLE CAPACITOR VD301 VHCSVC348S/-1 VIBRATORS X351 X352 X521 X701 X702 X801 RCRM-0007SJZZ RCRSP0006SJZZ RCRSP0005SJZZ RCRM-0008SJZZ RCRSP0011AWZZ RCRSP0002SJZZ CAPACITORS C101,102 C103,104 C105,106 C107,108 C109,110 C111,112 C113,114 C115,116 C117 C121,122 C123 C125 C126 C129,130 C131 C153 C154 C155 C201,202 C203,204 C208 –1– VCKYTV1HB102K VCKYTV1HB331K VCKYTV1HB271K RC-GZA476AF1C VCQYKA1HM153J RC-GZA106AF1C RC-GZA475AF1E VCKYTV1HB222K RC-GZA106AF1C VCCSTV1HL820J RC-GZA225AF1H RC-GZA107AF1E RC-GZA226AF1C RC-GZA475AF1E VCKYBT1HB821K VCQPKA2AA392J VCQYKA1HM273J RC-GZA107AF1C VCKYTV1HB562K RC-GZA105AF1H RC-GZA107AF1C XL-60H/70H NO. C209 C211,212 C213,214 C215,216 C301,302 C329 C330 C331 C332 C334 C335 C337 C340 C341 C343,344 C345~347 C348 C349 C350,351 C352 C353,354 C355 C356 C357 C358 C360,361 C362 C363 C364 C365 C366 C367,368 C369 C370~372 C373,374 C376 C380 C381 C382 C383 C384 C385 C386 C387 C391 C392 C393 C394 C395 C396 C397 C398 C399 C401~408 C411,412 C415,416 C417,418 C419,420 C421~424 C425,426 C429 C430 C521 C522 C523 C524 C525,526 C527 C535 C536 C537 C601 C602 C603,604 C605,606 C607,608 C609,610 C611,612 C613,614 C615 C616 C617,618 PRICE RANK PARTS CODE RC-GZA476AF1C VCKYTV1HB332K RC-GZA475AF1H RC-GZA105AF1H VCKYTV1HB102K VCKYTV1EF223Z VCCCPA1HH120J VCKYTV1EF473Z VCKYPA1HF223Z VCCUPA1HJ270J VCKYTV1HB561K VCKYPA1HF223Z VCKYTV1HB102K VCKYTV1EF223Z VCCSTV1HL330J VCKYTV1EF223Z RC-GZA107AF1C VCKYTV1HB102K VCKYTV1EF223Z RC-GZA106AF1C VCKYTV1EF223Z VCCSTV1HL220J VCKYTV1HB102K RC-GZA225AF1H RC-GZA105AF1H VCKYTV1EF223Z RC-GZA335AF1H VCKYTV1EF223Z RC-GZA106AF1C VCKYTV1EF223Z VCKYTV1HB102K RC-GZA105AF1H VCCSTV1HL560J RC-GZA105AF1H VCTYPA1CX153K VCKYTV1HB102K RC-GZA106AF1C VCCCTV1HH120J VCCCTV1HH150J VCKYTV1EF223Z VCKYTV1HB102K VCTYPA1CX103K VCKYPA1HB331K VCKYTV1EF223Z RC-GZA476AF1C VCKYTV1HB102K RC-GZA105AF1H RC-GZA476AF1C VCKYTV1EF223Z RC-GZA107AF1A VCKYTV1EF223Z RC-GZA107AF1A VCKYPA1HF223Z RC-GZA106AF1C VCKYTV1HB331K RC-GZA106AF1C RC-GZA225AF1H VCKYTV1HB272K RC-QZA104AFYJ RC-GZA106AF1C RC-GZA336AF1C RC-GZA107AF1C RC-GZA106AF1C VCKYTV1HB331K VCKYTV1EF104Z VCKYTV1HB561K VCCCTV1HH220J VCKYTV1EF104Z RC-GZA476AF1C VCKYTV1EF223Z VCKYPA1HF223Z RC-GZA336AF1C RC-GZA105AF1H VCKYPA1HB101K RC-GZA475AF1E RC-GZA227AF1E RC-GZA476AF1H RC-QZA224AFYJ RC-GZV108AF1V VCKYPA1HF223Z RC-GZW228AF1H VCKYPA1HB222K J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AB AA AB AB AA AA AA AB AB AA AA AB AA AA AA AA AB AA AA AB AA AA AA AB AB AA AB AA AB AA AA AB AA AB AA AA AB AA AA AA AA AA AA AA AB AA AB AB AA AB AA AB AB AB AA AB AB AA AC AB AB AB AB AA AA AA AA AA AB AA AB AB AB AA AB AB AB AB AD AB AH AA DESCRIPTION NO. 47 µF,16V,Electrolytic 0.0033 µF,50V 4.7 µF,50V,Electrolytic 1 µF,50V,Electrolytic 0.001 µF,50V 0.022 µF,25V 12 pF (CH),50V 0.047 µF,25V 0.022 µF,50V 27 pF (UJ),50V 560 pF,50V 0.022 µF,50V 0.001 µF,50V 0.022 µF,25V 33 pF,50V 0.022 µF,25V 100 µF,16V,Electrolytic 0.001 µF,50V 0.022 µF,25V 10 µF,16V,Electrolytic 0.022 µF,25V 22 pF,50V 0.001 µF,50V 2.2 µF,50V,Electrolytic 1 µF,50V,Electrolytic 0.022 µF,25V 3.3 µF,50V,Electrolytic 0.022 µF,25V 10 µF,16V,Electrolytic 0.022 µF,25V 0.001 µF,50V 1 µF,50V,Electrolytic 56 pF,50V 1 µF,50V,Electrolytic 0.015 µF,16V 0.001 µF,50V 10 µF,16V,Electrolytic 12 pF (CH),50V 15 pF (CH),50V 0.022 µF,25V 0.001 µF,50V 0.01 µF,16V 330 pF,50V 0.022 µF,25V 47 µF,16V,Electrolytic 0.001 µF,50V 1 µF,50V,Electrolytic 47 µF,16V,Electrolytic 0.022 µF,25V 100 µF,10V,Electrolytic 0.022 µF,25V 100 µF,10V,Electrolytic 0.022 µF,50V 10 µF,16V,Electrolytic 330 pF,50V 10 µF,16V,Electrolytic 2.2 µF,50V,Electrolytic 0.0027 µF,50V 0.1 µF,50V,Mylar 10 µF,16V,Electrolytic 33 µF,16V,Electrolytic 100 µF,16V,Electrolytic 10 µF,16V,Electrolytic 330 pF,50V 0.1 µF,25V 560 pF,50V 22 pF (CH),50V 0.1 µF,25V 47 µF,16V,Electrolytic 0.022 µF,25V 0.022 µF,50V 33 µF,16V,Electrolytic 1 µF,50V,Electrolytic 100 pF,50V 4.7 µF,25V,Electrolytic 220 µF,25V,Electrolytic 47 µF,50V,Electrolytic 0.22 µF,50V,Mylar 1000 µF,35V,Electrolytic 0.022 µF,50V 2200 µF,50V,Electrolytic 0.0022 µF,50V ! ! ! –2– C620 C621 C622 C624 C625 C626 C627 C629 C630 C632,633 C636,637 C639,640 C643,644 C647 C648 C651 C654 C656~659 C660 C661~663 C683 C684 C685 C686 C688 C689 C693,694 C695,696 C701,702 C703,704 C710 C711 C712 C713 C714 C715 C771 C772 C773 C801 C802 C803 C804 C805 C806 C807 C809 C810 C811 C812 C813 C817~819 C820 C821 C822 C823 C824,825 C826,827 C828,829 C830 C831,832 C833,834 C835 C836 C837 C838 C839 C840,841 C842 C843 C844 C845 C846,847 C848 C849 C850 C851 C852 C855 C857 C859 C860 PRICE RANK PARTS CODE RC-GZV477AF1E RC-GZA107AF1E VCKYPA1HF223Z VCKYPA1HF223Z RC-GZA106AF1C RC-GZA476AF1C VCKYTV1EF223Z RC-GZV227AF1H RC-GZW478AF1E VCKYPA1HF223Z VCKYPA1HF223Z VCKYPA1HB471K RC-QZA224AFYJ VCKYBT1HB331K VCKYPA1HB122K VCFYFA1HA104J VCFYFA1HA104J VCFYFA1HA104J VCKYPA1HF102Z VCKYPA1HB821K RC-GZV228AF1C VCFYFA1HA473J RC-GZA476AF1C VCKYPA1HF223Z VCKYPA1HF223Z RC-GZA476AF1C VCKYPA1HB331K VCKYPA1HB102K VCCCTV1HH220J VCKYTV1EF223Z VCKYTV1EB103K RC-GZA335AF1H VCKYTV1EB103K RC-GZA106AF1C VCKYTV1HB561K RC-GZA107AF1A RC-GZA476AF1C VCKYTV1EB104K RC-GZA476AF1C VCCSPA1HL101J VCKYTV1EB153K RC-GZA476AF1A VCKYTV1EB103K VCKYTV1HB272K VCKYTV1HB472K VCKYTV1EB333K VCKYTV1HB472K VCKYTV1HB102K RC-GZA476AF1A VCKYTV1EF103Z RC-GZA107AF1A VCKYTV1EB104K VCKYTV1EF103Z VCKYTV1EB104K RC-GZA227AF1A VCKYTV1EF103Z VCKYTV1EB563K VCCCTV1HH150J RC-GZA107AF1A VCKYTV1EB563K RC-GZA106AF1C VCKYTV1HB471K VCKYTV1EB563K RC-GZA107AF1A VCKYTV1HB471K RC-GZA476AF1A VCCSTV1HL2R0C RC-GZA107AF1A RC-GZA476AF1A VCKYTV1EF104Z VCKYTV1HB682K RC-GZA107AF1A VCKYTV1EF104Z VCCSTV1HL390J VCKYTV1EB563K RC-GZA227AF1A RC-GZA107AF1A VCQYKA1HM222J RC-GZA107AF1A RC-GZA476AF1C RC-GZA477AF1A VCKYTV1EF104Z J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AC AB AB AB AB AB AA AC AG AB AB AA AB AA AA AC AC AC AA AG AB AB AB AB AB AA AA AA AA AA AB AA AB AA AB AB AA AB AA AB AB AA AA AA AB AA AA AB AA AB AA AA AA AB AA AA AA AB AA AB AA AA AB AA AB AA AB AB AA AA AB AA AA AA AB AB AB AB AB AC AA DESCRIPTION 470 µF,25V,Electrolytic 100 µF,25V,Electrolytic 0.022 µF,50V 0.022 µF,50V 10 µF,16V,Electrolytic 47 µF,16V,Electrolytic 0.022 µF,25V 220 µF,50V,Electrolytic 4700 µF,25V,Electrolytic 0.022 µF,50V 0.022 µF,50V 470 pF,50V 0.22 µF,50V,Mylar 330 pF,50V 0.0012 µF,50V 0.1 µF,50V,Thin Film 0.1 µF,50V,Thin Film 0.1 µF,50V,Thin Film 0.001 µF,50V 820 pF,50V 2200 µF,16V,Electrolytic 0.047 µF,50V,Thin Film 47 µF,16V,Electrolytic 0.022 µF,50V 0.022 µF,50V 47 µF,16V,Electrolytic 330 pF,50V 0.001 µF,50V 22 pF (CH),50V 0.022 µF,25V 0.01 µF,25V 3.3 µF,50V,Electrolytic 0.01 µF,25V 10 µF,16V,Electrolytic 560 pF,50V 100 µF,10V,Electrolytic 47 µF,16V,Electrolytic 0.1 µF,25V 47 µF,16V,Electrolytic 100 pF,50V 0.015 µF,25V 47 µF,10V,Electrolytic 0.01 µF,25V 0.0027 µF,50V 0.0047 µF,50V 0.033 µF,25V 0.0047 µF,50V 0.001 µF,50V 47 µF,10V,Electrolytic 0.01 µF,25V 100 µF,10V,Electrolytic 0.1 µF,25V 0.01 µF,25V 0.1 µF,25V 220 µF,10V,Electrolytic 0.01 µF,25V 0.056 µF,25V 15 pF (CH),50V 100 µF,10V,Electrolytic 0.056 µF,25V 10 µF,16V,Electrolytic 470 pF,50V 0.056 µF,25V 100 µF,10V,Electrolytic 470 pF,50V 47 µF,10V,Electrolytic 2 pF,50V 100 µF,10V,Electrolytic 47 µF,10V,Electrolytic 0.1 µF,25V 0.0068 µF,50V 100 µF,10V,Electrolytic 0.1 µF,25V 39 pF,50V 0.056 µF,25V 220 µF,10V,Electrolytic 100 µF,10V,Electrolytic 0.0022 µF,50V,Mylar 100 µF,10V,Electrolytic 47 µF,16V,Electrolytic 470 µF,10V,Electrolytic 0.1 µF,25V XL-60H/70H NO. PARTS CODE C861 C862 C863 C871 C872 C887 C901 C902 C903 C904,905 VCKYPA1HB102K VCKYPA1HB222K VCKYTV1HB471K RC-GZA476AF1C VCKYTV1EB104K VCKYTV1HB272K VCKYTV1HB102K RC-GZA335AF1H RC-GZA107AF1E VCKYTV1HF223Z PRICE RANK DESCRIPTION J J J J J J J J J J AA AA AA AB AA AA AA AB AB AA 0.001 µF,50V 0.0022 µF,50V 470 pF,50V 47 µF,16V,Electrolytic 0.1 µF,25V 0.0027 µF,50V 0.001 µF,50V 3.3 µF,50V,Electrolytic 100 µF,25V,Electrolytic 0.022 µF,50V J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA 0 ohm,Jumper,1.25×2mm,Green 120 ohms,1/10W 120 ohms,1/10W 1 kohm,1/10W 1 kohm,1/10W 100 kohm,1/10W 100 ohm,1/4W 120 ohms,1/10W 10 kohm,1/10W 1 kohm,1/10W 1 kohm,1/10W 82 ohms,1/10W 3.3 kohms,1/6W 10 kohm,1/10W 47 kohms,1/10W 2.2 kohms,1/10W 82 ohms,1/10W 82 ohms,1/10W 82 ohms,1/10W 82 ohms,1/10W 82 ohms,1/10W 82 ohms,1/10W 82 ohms,1/10W 82 ohms,1/10W 82 ohms,1/10W 82 kohms,1/10W 68 kohms,1/10W 82 kohms,1/10W 82 kohms,1/6W 82 kohms,1/10W 68 kohms,1/6W 1 kohm,1/6W 120 ohms,1/10W 150 kohms,1/10W 150 kohms,1/6W 10 kohm,1/6W 10 kohm,1/10W 3.9 kohms,1/10W 2.2 kohms,1/6W 3.3 kohms,1/10W 15 kohms,1/10W 22 kohms,1/10W 100 ohm,1/10W 4.7 kohms,1/10W 100 kohm,1/10W 5.6 kohms,1/10W 4.7 kohms,1/6W 4.7 kohms,1/10W 1 kohm,1/10W 100 kohm,1/10W 330 ohms,1/4W 2.7 kohms,1/6W 10 kohm,1/10W 330 ohms,1/6W 47 kohms,1/10W 100 kohm,1/10W 10 kohm,1/10W 56 ohms,1/4W 150 ohms,1/4W 8.2 kohms,1/6W 8.2 kohms,1/10W 100 kohm,1/10W 10 kohm,1/10W 47 kohms,1/6W 330 ohms,1/4W 10 kohm,1/10W 10 kohm,1/6W 2.7 kohms,1/10W 2.7 kohms,1/6W RESISTORS J920 J923 R7A0 R7A1 R7A2 R7A3 R7A4 R7A5 R7A6 R7A7 R7A8 R7A9 R7B0 R7B2 R7B3 R7D1 R7D2 R7D3 R7D4 R7D5 R7D6 R7D8 R7D9 R7E1 R80A R80B R80C R80E R80F R80G R101,102 R103,104 R105 R106 R107 R108 R109,110 R111,112 R113,114 R115,116 R117,118 R119,120 R121~124 R125 R126 R131 R132 R133 R134 R138 R139 R140 R141 R151 R152 R153,154 R155 R156,157 R201 R202 R203,204 R205,206 R207 R208 R209 R210 R211 R212 VRS-TV2AB000J VRS-TV2AB121J VRS-TV2AB121J VRS-TV2AB102J VRS-TV2AB102J VRS-TV2AB104J VRD-ST2EE101J VRS-TV2AB121J VRS-TV2AB103J VRS-TV2AB102J VRS-TV2AB102J VRS-TV2AB820J VRD-ST2CD332J VRS-TV2AB103J VRS-TV2AB473J VRS-TV2AB222J VRS-TV2AB820J VRS-TV2AB820J VRS-TV2AB820J VRS-TV2AB820J VRS-TV2AB820J VRS-TV2AB820J VRS-TV2AB820J VRS-TV2AB820J VRS-TV2AB820J VRS-TV2AB823J VRS-TV2AB683J VRS-TV2AB823J VRD-ST2CD823J VRS-TV2AB823J VRD-ST2CD683J VRD-ST2CD102J VRS-TV2AB121J VRS-TV2AB154J VRD-ST2CD154J VRD-ST2CD103J VRS-TV2AB103J VRS-TV2AB392J VRD-ST2CD222J VRS-TV2AB332J VRS-TV2AB153J VRS-TV2AB223J VRS-TV2AB101J VRS-TV2AB472J VRS-TV2AB104J VRS-TV2AB562J VRD-ST2CD472J VRS-TV2AB472J VRS-TV2AB102J VRS-TV2AB104J VRD-ST2EE331J VRD-ST2CD272J VRS-TV2AB103J VRD-ST2CD331J VRS-TV2AB473J VRS-TV2AB104J VRS-TV2AB103J VRD-ST2EE560J VRD-ST2EE151J VRD-ST2CD822J VRS-TV2AB822J VRS-TV2AB104J VRS-TV2AB103J VRD-ST2CD473J VRD-ST2EE331J VRS-TV2AB103J VRD-ST2CD103J VRS-TV2AB272J VRD-ST2CD272J NO. R213~216 R217 R218 R323 R336 R343 R344 R345 R346 R347 R348 R349 R350 R351 R352 R353 R355 R356 R357 R358 R359 R360 R361,362 R363 R364 R365 R366 R369A R369B R371~374 R376 R377 R379 R380 R381 R382 R383 R384 R385 R386 R387 R391,392 R393 R395 R405,406 R407,408 R415~425 R435,436 R437,438 R439,440 R521 R528,529 R532 R533,534 R601,602 R603,604 R605,606 R607 R608 R609,610 R613,614 R615,616 R617 R619,620 R621 R623 R624 R625 R627 R628 R629 R631,632 R633 R634 R651 R661,662 R681 R682 R683 R684 R685 R686 –3– PRICE RANK PARTS CODE VRS-TV2AB123J VRD-ST2CD123J VRS-TV2AB122J VRS-TV2AB683J VRD-ST2CD103J VRD-ST2CD181J VRS-TV2AB681J VRS-TV2AB472J VRD-ST2CD331J VRS-TV2AB682J VRS-TV2AB681J VRS-TV2AB330J VRS-TV2AB272J VRS-TV2AB562J VRS-TV2AB102J VRS-TV2AB271J VRS-TV2AB332J VRS-TV2AB102J VRS-TV2AB474J VRS-TV2AB822J VRS-TV2AB182J VRS-TV2AB472J VRS-TV2AB123J VRD-ST2CD682J VRS-TV2AB682J VRS-TV2AB103J VRS-TV2AB222J VRS-TV2AB680J VRS-TV2AB820J VRS-TV2AB102J VRD-ST2CD103J VRD-ST2CD562J VRS-TV2AB222J VRD-ST2CD152J VRS-TV2AB103J VRD-ST2EE331J VRS-TV2AB562J VRD-ST2CD682J VRD-ST2CD562J VRD-ST2EE331J VRD-ST2CD562J VRD-ST2EE391J VRS-TV2AB102J VRD-ST2CD473J VRS-TV2AB273J VRS-TV2AB152J VRS-TV2AB102J VRS-TV2AB103J VRS-TV2AB682J VRS-TV2AB392J VRD-ST2CD473J VRD-ST2CD102J VRS-TV2AB103J VRD-ST2CD563J VRD-ST2CD102J VRD-ST2CD103J VRD-ST2CD820J VRD-ST2CD682J VRD-ST2CD102J VRD-ST2EE3R3J VRD-RT2HD271J VRD-ST2CD472J VRS-TV2AB333J VRD-ST2EE470J VRS-TV2AB223J VRS-TV2AB223J VRD-ST2EE102J VRS-TV2AB103J VRS-TV2AB103J VRD-ST2EE101J VRD-ST2EE821J VRD-ST2EE6R8J VRD-ST2EE100J VRD-ST2EE332J VRS-VV3LA681J VRD-ST2EE331J VRD-ST2CD470J VRD-ST2CD122J VRD-ST2CD470J VRD-ST2CD122J VRD-ST2CD103J VRD-ST2CD473J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AC AA AA AA AA AA AA AA DESCRIPTION 12 kohms,1/10W 12 kohms,1/6W 1.2 kohms,1/10W 68 kohms,1/10W 10 kohm,1/6W 180 ohms,1/6W 680 ohms,1/10W 4.7 kohms,1/10W 330 ohms,1/6W 6.8 kohms,1/10W 680 ohms,1/10W 33 ohms,1/10W 2.7 kohms,1/10W 5.6 kohms,1/10W 1 kohm,1/10W 270 ohms,1/10W 3.3 kohms,1/10W 1 kohm,1/10W 470 kohms,1/10W 8.2 kohms,1/10W 1.8 kohms,1/10W 4.7 kohms,1/10W 12 kohms,1/10W 6.8 kohms,1/6W 6.8 kohms,1/10W 10 kohm,1/10W 2.2 kohms,1/10W 68 ohms,1/10W 82 ohms,1/10W 1 kohm,1/10W 10 kohm,1/6W 5.6 kohms,1/6W 2.2 kohms,1/10W 1.5 kohms,1/6W 10 kohm,1/10W 330 ohms,1/4W 5.6 kohms,1/10W 6.8 kohms,1/6W 5.6 kohms,1/6W 330 ohms,1/4W 5.6 kohms,1/6W 390 ohms,1/4W 1 kohm,1/10W 47 kohms,1/6W 27 kohms,1/10W 1.5 kohms,1/10W 1 kohm,1/10W 10 kohm,1/10W 6.8 kohms,1/10W 3.9 kohms,1/10W 47 kohms,1/6W 1 kohm,1/6W 10 kohm,1/10W 56 kohms,1/6W 1 kohm,1/6W 10 kohm,1/6W 82 ohms,1/6W 6.8 kohms,1/6W 1 kohm,1/6W 3.3 ohms,1/4W 270 ohms,1/2W 4.7 kohms,1/6W 33 kohms,1/10W 47 ohms,1/4W 22 kohms,1/10W 22 kohms,1/10W 1 kohm,1/4W 10 kohm,1/10W 10 kohm,1/10W 100 ohm,1/4W 820 ohms,1/4W 6.8 ohms,1/4W 10 ohm,1/4W 3.3 kohms,1/4W 680 kohms,3W,Metal Oxide Film 330 ohms,1/4W 47 ohms,1/6W 1.2 kohms,1/6W 47 ohms,1/6W 1.2 kohms,1/6W 10 kohm,1/6W 47 kohms,1/6W XL-60H/70H NO. R701 R702 R705 R706 R707 R708 R709 R710,711 R714 R715 R716 R717 R718 R719,720 R721,722 R723 R724 R725 R727 R728 R729 R730~735 R737~746 R747~749 R750,751 R752 R753,754 R755 R757~777 R778~781 R782,783 R784 R785 R786 R787 R789 R792 R793 R794~797 R798 R799 R801 R802 R804 R806 R807 R808 R809 R810 R811 R812 R813 R814 R815,816 R817,818 R819 R820 R821 R822 R823 R824 R825 R826 R827 R828 R829 R843 R851 R852~855 R861~863 R872 R873 R874 R876 R877 R880 R901 R902 R903 R904 R905 R906 PRICE RANK PARTS CODE VRD-ST2CD103J VRS-TV2AB103J VRD-ST2CD562J VRD-ST2CD392J VRD-ST2CD272J VRS-TV2AB222J VRD-ST2CD152J VRS-TV2AB122J VRD-ST2CD562J VRD-ST2CD392J VRD-ST2CD272J VRD-ST2CD222J VRD-ST2CD152J VRD-ST2CD122J VRS-TV2AB103J VRS-TV2AB473J VRS-TV2AB122J VRS-TV2AB103J VRS-TV2AB473J VRS-TV2AB102J VRS-TV2AB473J VRS-TV2AB102J VRS-TV2AB102J VRD-ST2CD102J VRS-TV2AB102J VRD-ST2CD102J VRS-TV2AB102J VRD-ST2CD102J VRS-TV2AB102J VRS-TV2AB473J VRS-TV2AB333J VRD-ST2CD473J VRS-TV2AB102J VRD-ST2CD473J VRD-RT2HD2R2J VRD-ST2CD473J VRD-ST2CD473J VRD-ST2CD222J VRD-ST2CD181J VRD-ST2CD822J VRD-ST2CD222J VRD-ST2CD103J VRS-TV2AB473J VRS-TV2AB104J VRS-TV2AB153J VRS-TV2AB103J VRS-TV2AB332J VRS-TV2AB103J VRS-TV2AB332J VRS-TV2AB222J VRS-TV2AB332J VRD-ST2EE100J VRS-TV2AB332J VRD-ST2CD103J VRS-TV2AB102J VRD-ST2CD221J VRS-TV2AB102J VRD-ST2CD151J VRD-ST2EE220J VRD-ST2CD102J VRS-TV2AB273J VRS-TV2AB823J VRS-TV2AB272J VRS-TV2AB273J VRS-TV2AB122J VRD-ST2CD683J VRD-ST2CD102J VRD-ST2CD331J VRS-TV2AB104J VRS-TV2AB222J VRD-RT2HD2R2J VRD-ST2CD562J VRS-TV2AB222J VRS-TV2AB154J VRS-TV2AB683J VRS-TV2AB473J VRD-ST2CD152J VRD-ST2CD563J VRS-TV2AB473J VRS-TV2AB271J VRS-TV2AB103J VRD-ST2CD152J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA DESCRIPTION NO. 10 kohm,1/6W 10 kohm,1/10W 5.6 kohms,1/6W 3.9 kohms,1/6W 2.7 kohms,1/6W 2.2 kohms,1/10W 1.5 kohms,1/6W 1.2 kohms,1/10W 5.6 kohms,1/6W 3.9 kohms,1/6W 2.7 kohms,1/6W 2.2 kohms,1/6W 1.5 kohms,1/6W 1.2 kohms,1/6W 10 kohm,1/10W 47 kohms,1/10W 1.2 kohms,1/10W 10 kohm,1/10W 47 kohms,1/10W 1 kohm,1/10W 47 kohms,1/10W 1 kohm,1/10W 1 kohm,1/10W 1 kohm,1/6W 1 kohm,1/10W 1 kohm,1/6W 1 kohm,1/10W 1 kohm,1/6W 1 kohm,1/10W 47 kohms,1/10W 33 kohms,1/10W 47 kohms,1/6W 1 kohm,1/10W 47 kohms,1/6W 2.2 ohms,1/2W 47 kohms,1/6W 47 kohms,1/6W 2.2 kohms,1/6W 180 ohms,1/6W 8.2 kohms,1/6W 2.2 kohms,1/6W 10 kohm,1/6W 47 kohms,1/10W 100 kohm,1/10W 15 kohms,1/10W 10 kohm,1/10W 3.3 kohms,1/10W 10 kohm,1/10W 3.3 kohms,1/10W 2.2 kohms,1/10W 3.3 kohms,1/10W 10 ohm,1/4W 3.3 kohms,1/10W 10 kohm,1/6W 1 kohm,1/10W 220 ohms,1/6W 1 kohm,1/10W 150 ohms,1/6W 22 ohms,1/4W 1 kohm,1/6W 27 kohms,1/10W 82 kohms,1/10W 2.7 kohms,1/10W 27 kohms,1/10W 1.2 kohms,1/10W 68 kohms,1/6W 1 kohm,1/6W 330 ohms,1/6W 100 kohm,1/10W 2.2 kohms,1/10W 2.2 ohms,1/2W 5.6 kohms,1/6W 2.2 kohms,1/10W 150 kohms,1/10W 68 kohms,1/10W 47 kohms,1/10W 1.5 kohms,1/6W 56 kohms,1/6W 47 kohms,1/10W 270 ohms,1/10W 10 kohm,1/10W 1.5 kohms,1/6W R907 R909 R910 PRICE RANK PARTS CODE VRD-ST2CD103J VRS-TV2AB183J VRS-TV2AB333J J J J DESCRIPTION AA 10 kohm,1/6W AA 18 kohms,1/10W AA 33 kohms,1/10W OTHER CIRCUITRY PARTS ! ! ! ! –4– BI605/CNS605 BI651/CNS651 BI652/CNS652 BI702/CNS702 BI706/CNS706 BI707/CNS707 BI801/CNS801 BI802/CNS802 BI803/CNS803 BI805/CNS805 BI901/CNS901 CFM901 QCNWN0179SJZZ QCNWN0177SJZZ QCNWN0194SJZZ QCNWN0181SJZZ QCNWN0185SJZZ QCNWN0125SJZZ QCNWN0186SJZZ QCNWN0187SJZZ QCNWN0188SJZZ QCNWN0189SJZZ QCNWN0176SJZZ ———— J J J J J J J J J J J AF AC AC AF AC AE AF AE AE AD AE — CFW601 CFW701 CFW704 CFW806 CFW807 CNP101 CNP301 CNP604 CNP605 CNP651 CNP652,653 CNP702 CNP703 CNP705 CNP706 CNP707 CNP803 CNP804 CNP805 CNP901 QCNWN0201SJZZ QCNWN0200SJZZ QCNWN0183SJZZ QCNWN0191SJZZ QCNWN0182SJZZ QCNCM931HAFZZ QCNCM602BAFZZ QCNCM010NAWZZ QCNCM705GAFZZ QCNCM998BAFZZ QCNCM998BAFZZ QCNCM004NSJZZ QCNCM010MAWZZ QCNCM932BAFZZ QCNCM932CAFZZ QCNCM603CAFZZ QCNCM932FAFZZ QCNCM931BAFZZ QCNCM999CAFZZ ———— J J J J J J J J J J J J J J J J J J J AB AB AD AB AB AC AA AC AB AC AC AC AC AA AA AB AC AA AG — CNS101 CNS604 CNS703 CNS704 CNS705 CNS804 F651 F652 FE301 J601 J801 LCD701 M701 M801 M901(237-9) NM801 NM802 NSW801 PH901 QCNWN0175SJZZ J QCNCW010NAWZZ J QCNCW010MAWZZ J QCNCW623MAFZZ J QCNWN0184SJZZ J QCNWN0193SJZZ J QFS-C322ASJNI J QFS-C132ASJNI J RTUNS0012AWZZ J QJAKM0001SJZZ J VHPGP1F32T/-1 J RV-LX0007SJZZ J RMOTV0409AFZZ J RMOTV0409AFZZ J 9GD192112344 J RMOTV0409AFM1 J RMOTV0408AFM3 J QSW-F9001AWZZ J ———— AG AC AD AC AB AF AH AV AG AP AR AL AL AY AN AN AE — RLY601 RX701 SO301 SO401 SO601 SO651 SOL901(237-4) SW700 SW709 RRLYD0004SJZZ VHLN64H380A-1 QTANC0001SJZZ QSOCJ0003SJZZ QTANA0007SJZZ QSOCA0004SJZZ 9GD19212118 QSW-Z0001SJZZ QSW-K0002SJZZ J J J J J J J J J AG AK AF AG AF AH AP AF AC SW710 QSW-K0002SJZZ J AC SW711 SW712 QSW-K0002SJZZ QSW-K0002SJZZ J J AC AC SW713 QSW-K0002SJZZ J AC SW714 QSW-K0002SJZZ J AC SW715 SW716 SW717 QSW-K0002SJZZ QSW-K0002SJZZ QSW-K0002SJZZ J J J AC AC AC Connector Ass’y,7/7Pin Connector Ass’y,2/2Pin Connector Ass’y,2/2Pin Connector Ass’y,13/13Pin Connector Ass’y,3/3Pin Connector Ass’y,3/3Pin Connector Ass’y,8/8Pin Connector Ass’y,7/7Pin Connector Ass’y,6/6Pin Connector Ass’y,3/3Pin Connector Ass’y,7/7Pin Flat Wire,2Pin (Supplies at REF.No.PWB-D) Flat Wire,5Pin Flat Wire,2Pin Flat Wire,12Pin Flat Wire,3Pin Flat Wire,2Pin Plug,8Pin Plug,2Pin Plug,13Pin Plug,7Pin Plug,2Pin Plug,2Pin Plug,13Pin Plug,12Pin Plug,2Pin Plug,3Pin Plug,3Pin Plug,6Pin Plug,2Pin Plug,3Pin Plug,7Pin (Supplies at REF.No.PWB-D) Connector Ass’y,8Pin Socket,13Pin Socket,12Pin Socket,12Pin Connector Ass’y,2Pin Connector Ass’y,2Pin Fuse,T3.15A L 250V Fuse,T1.25A L 250V FM Front End Jack,Headphones Jack,CD Digital Output LCD Display Motor [JOG] Motor [CD Lid] Motor with Pulley [Tape] Motor with Gear [Sled] Motor with Chassis [Spindle] Switch,Push Type [Pickup In] Photo Interrupter (Supplies at REF.No.PWB-E) Relay Remote Sensor,N64H380A Socket,FM Antenna Jack,Video/AUX Terminal,Speaker Socket,AC Power Input Solenoid Ass’y Switch,Push Type [JOG] Switch,Key Type [ON/STAND-BY] Switch,Key Type [CLOCK/TIMER/SLEEP] Switch,Key Type [TUNING UP] Switch,Key Type [PLAY/CD PAUSE] Switch,Key Type [VOLUME SELECT] Switch,Key Type [DISPLAY MODE] Switch,Key Type [ASPM] Switch,Key Type [EON] Switch,Key Type [PTY.TI] XL-60H/70H NO. PRICE RANK PARTS CODE SW718 SW721 QSW-K0002SJZZ QSW-K0002SJZZ J J SW722 QSW-K0002SJZZ J SW723 SW724 SW725 SW726 QSW-K0002SJZZ QSW-K0002SJZZ QSW-K0002SJZZ QSW-K0002SJZZ J J J J SW727 SW728 QSW-K0002SJZZ QSW-K0002SJZZ J J SW730 QSW-K0002SJZZ J SW802 QSW-B0001SJZZ SW901(237-7) 9GD640101210 SW902(237-8) 9GD640101210 J J J DESCRIPTION AC Switch,Key Type [SURROUND] AC Switch,Key Type [MEMORY/SET] AC Switch,Key Type [BASS/TREBLE] AC Switch,Key Type [BAND] AC Switch,Key Type [REC.PAUSE] AC Switch,Key Type [STOP/CLEAR] AC Switch,Key Type [TUNING DOWN] AC Switch,Key Type [FUNCTION] AC Switch,Key Type [VOLUME/JOG] AC Switch,Key Type [CD Lid Open/Close] AG Switch,Lever Type [CD Lid] AE Switch,Leaf Type [Fool Proof] AE Switch,Leaf Type [Cam] CD MECHANISM PARTS ! 301 302 303 304 305 306 306- 1 NGERH0586AFZZ NGERH0587AFZZ MLEVP1054AFZZ NSFTM0291AFFW PCUSG0613AFZZ DCTRH8004SJ01 ———— J J J J J J AC AC AC AD AC BC — 306- 2 306- 3 307 701 702 703 704 NM801 NM802 NSW801 NGERR0043AFZZ MSPRC0961AFZZ PCOVP1333AFSA XBSSD26P06000 XHBSD20P05000 XBBSD20P03000 LX-WZ1070AFZZ RMOTV0409AFM1 RMOTV0408AFM3 QSW-F9001AWZZ J J J J J J J J J J AC AA AF AA AA AA AA AN AN AE Gear,Middle Gear,Drive Rail,Guide Shaft,Guide Cushion Pickup Unit Ass’y Pickup Unit (Not Replacement Item) Gear,Rack Spring,Rack Cover,Mechanism Screw,ø2.6×6mm Screw,ø2×5mm Screw,ø2×3mm Washer,ø1.5×ø3.8×0.25mm Motor with Gear [Sled] Motor with Chassis [Spindle] Switch,Push Type [Pickup In] CABINET PARTS 201 201 201- 1 CPNLC1047SJ02 CPNLC1047SJ04 ———— J J 201- 2 201- 3 201- 4 201- 5 201- 6 201- 6 201- 7 201- 8 JKNBZ0036SJSA PCOVS3004SJFW PCUSG0003SJZZ QCNWN0219SJZZ GDORF0012SJSA GDORF0013SJSA HDECP0001SJSA HDECP0002SJSA J J J J J J J J AE AC AC AC AH AH AF AF 201- 9 201-10 201-11 201-12 201-13 203 HDECQ0028SJSA HDECQ0029SJSA JKNBZ0035SJSB MSPRD0006SJFJ LX-EZ0001SJFN CGERH0001SJ01 J J J J J J AE AE AF AC AB AF 204 204 205 206 208 209 210 210 212 212 214 214 216 216- 1 HDECQ0034SJSA HDECQ0034SJSB LANGF0021SJFF MSPRC0006SJFJ HDECQ0033SJSA JKNBK0025SJSB GCABC1040SJSA GCABC1040SJSB GDORT0004SJSA GDORT0004SJSB JKNBZ0040SJSA JKNBZ0040SJSB CHLDM1002SJ01 ———— J J J J J J J J J J J J J AG AF AF AB AD AC AK AK AG AK AE AC AH — 216- 2 217 217 218 PMAGF0002AWZZ GITAS0003SJSA GITAS0003SJSB GITAS0004SJSA J J J J AE AG AK AG — Front Panel Ass’y [XL-60H] Front Panel Ass’y [XL-70H] Front Panel (Not Replacement Item) Button,Operation B Shield Cover Cushion,Leg Lead Wire with Lug Cassette Holder [XL-60H] Cassette Holder [XL-70H] Decoration Plate,LCD Display Decoration Plate,Cassette Holder LCD Window Cassette Holder Window Button,Operation A Spring,Cassette Holder Screw,ø2.5×10mm Cassette Holder Damper Gear Ass’y Panel,CD Lid [XL-60H] Panel,CD Lid [XL-70H] Bracket,CD Lid Spring,CD Eject Button Ring,JOG Dial Knob Knob,JOG Dial Top Cabinet [XL-60H] Top Cabinet [XL-70H] CD Lid [XL-60H] CD Lid [XL-70H] Button,CD Eject [XL-60H] Button,CD Eject [XL-70H] Stabilizer Ass’y Stabilizer (Not Replacement Item) Magnet Side Panel,Left [XL-60H] Side Panel,Left [XL-70H] Side Panel,Right [XL-60H] NO. 218 219 220 221 222 ! PRICE RANK PARTS CODE GITAS0004SJSB TLABS0003SJZZ TLABS0004SJZZ GCABB1022SJSB PCOVS3001SJFW J J J J J AK AD AC AG AG 223 LCHSM0004SJFW 224 LANGF0023SJFW 225 LHLDW1001SJZZ 226 QCNWN0148SJZZ 227 QFSHD0001AWZZ 228 LANGK0019SJFW 229 PRDAR0017SJFW 230 PRDAR0018SJFW 231 PCOVS3003SJFW 232 PSHEP0001SJZZ 233 LHLDZ1010SJSA 234 LHLDZ1022SJSA 237 CMECB0004SJ01 237- 1 94R19210703 237- 2 9GD19210943 237- 3 94R192104309 237- 4(SOL901) 9GD19212118 237- 5 9GD62161401 237- 6 94R62010111 237- 7(SW901) 9GD640101210 237- 8(SW902) 9GD640101210 237- 9(M901) 9GD192112344 237-10(PWB-D) 9GD192121303 237-11(PWB-E) 9GD192121304 238 QCNWN0147SJZZ 240 LHLDZ1023SJZZ 241 LHLDZ1024SJZZ 242 LHLDZ1026SJZZ 243 NBLTK0001SJZZ 244 NGERW0001SJZZ 245 NGERW0002SJZZ 246 NPLYP0001SJZZ 247 PCOVU9001SJZZ 248 LANGF0011SJZZ J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AN AD AD AD AB AB AP AH AD AF AE AB BC AE AG AG AP AN AT AE AE AY AZ AW AC AD AC AC AA AD AD AB AC AD 249 LANGT0001SJFW J AD 250 PCOVP1001SJSB J AG 251 252 253 254 255 256 NPLYP0001SJZZ LHLDZ1031SJZZ NBLTK0002SJZZ NGERW0001SJZZ NGERW0003SJZZ TSPC-0107SJZZ J J J J J J AB AE AC AD AD AC 256 TSPC-0108SJZZ J AC 256 TSPC-0111SJZZ J AC 256 TSPC-0112SJZZ J AC 257 257 601 603 604 605 608 609 610 611 612 613 614 615 616 617 TLABN0070SJZZ TLABN0072SJZZ XEBSD25P10000 XEBSF25P08000 XJBSD30P08000 LX-JZ0001SJFD XHBSD20P05000 XEBSD25P14000 XESSD25P12000 XESSD30P10000 XHBSD30P06000 XJBSF30P10000 XJBSD30P10000 LX-EZ0001SJFN XEBSF25P10000 XHBSD40P06000 J J J J J J J J J J J J J J J J AC –5– AA AA AA AA AA AA AA AA AA AA AB AC AA DESCRIPTION Side Panel,Right [XL-70H] Label,Class 3A Label,Laser Rear Panel Bracket,FM/AM Socket/Video/ AUX/Speaker Terminal Main Chassis Bracket,Sub Transformer Nylon Band Lead Wire with Lug Holder,Fuse Bracket,Display PWB/Main PWB Heat Sink,Power Amp. PWB Heat Sink,Main PWB Shield Cover,Main PWB Sheet,LCD Display Holder,LCD Display Holder,LED Tape Mechanism Ass’y Belt,FF/REW Belt,Main Pinch Roller Arm Ass’y Solenoid Ass’y Head,Erase Head,Record/Playback Switch,Leaf Type [Fool Proof] Switch,Leaf Type [Cam] Motor with Pulley [Tape] Tape Mechanism PWB Ass’y Tape Mechanism PWB Ass’y Lead Wire with Lug Holder,JOG Motor Holder,JOG Motor Tray Holder,JOG Motor Guide Belt,JOG Motor Gear,Worm,JOG Motor Wheel,JOG Worm Pulley,JOG Motor Sheet,JOG Motor Guide Holder Bracket,Heat Sink, Power Amp. PWB Bracket,Power Amp. PWB/Main PWB Cover,Heat Sink, Power Amp. PWB Pulley,CD Lid Motor Holder,CD Lid Motor Belt,CD Lid Motor Gear,Worm,CD Lid Motor Gear,CD Lid Motor Worm Gear Label,Specifications [XL-60H for Europe] Label,Specifications [XL-60H for U.K.] Label,Specifications [XL-70H for Europe] Label,Specifications [XL-70H for U.K.] Label,Serial No. [XL-60H] Label,Serial No. [XL-70H] Screw,ø2.5×10mm Screw,ø2.5×8mm Screw,ø3×8mm Screw,ø3×10mm Screw,ø2×5mm Screw,ø2.5×14mm Screw,ø2.5×12mm Screw,ø3×10mm Screw,ø3×6mm Screw,ø3×10mm Screw,ø3×10mm Screw,ø2.5×10mm Screw,ø2.5×10mm Screw,ø4×6mm XL-60H/70H NO. PRICE RANK PARTS CODE DESCRIPTION NO. ACCESSORIES/PACKING PARTS (For Europe) ! QACCE0001SJZZ QANTL0002SJZZ QANTW0002SJZZ SPAKA0040SJZZ J J J J AH AM AH AG SPAKA0041SJZZ J AG SPAKA0052SJZZ J SPAKC0101SJZZ SPAKC0103SJZZ SPAKP0005SJZZ J J J AM AQ AC SPAKZ0019SJZZ J AC SSAKA0002SJZZ TINSZ0056SJZZ TLABE0054SJZZ TLABM0022SJZZ TLABM0024SJZZ TLABZ0030SJZZ J J J J J J AE AM RRMCG0014SJSB J GFTAB1021AWSB J AS AC AD AC 1 2 3 4 4-1 5 QACCB0001SJ00 QANTL0002SJZZ QANTW0002SJZZ RRMCG0014SJSB GFTAB1021AWSB SPAKA0043SJZZ J J J J J J AW AM AH AS 6 6 7 SPAKC0110SJZZ SPAKC0111SJZZ SPAKP0002SJZZ J J J AN AN AD 8 SPAKP0003SJZZ J AC 9 10 11 11 12 13 14 SSAKA0002SJZZ TINSE0037SJZZ TLABM0022SJZZ TLABM0024SJZZ TINSE0042SJZZ TLABE0054SJZZ TCADN0001SJZZ J J J J J J J AE AE AC AD AB AK AE AC Power Supply Cord AM Loop Antenna FM Antenna Remote Control Battery Lid,Remote Control Packing Add.,Left/Right [For U.K. Only] Packing Case [XL-60H] Packing Case [XL-70H] Polyethylene Sheet,Unit [For U.K. Only] Polyethylene Sheet,AC Power Supply Cord [For U.K. Only] Polyethylene Bag,Accessories Operation Manual Label,Feature [XL-60H] Label,Feature [XL-70H] Quick Guide [For U.K. Only] Label,Bar Code,Packing Case R-Card [For U.K. Only] P.W.B. ASSEMBLY (Not Replacement Item) ! PWB-A1~10 DCEKL0002SJ03 J PWB-B1,2 DCEKJ0005SJ06 J PWB-C PWB-D PWB-E QPWBF3895AFZZ 9GD192121303 9GD192121304 J J J — Main/Display/CD/LED/ Headphones/Open•Close Switch/JOG Switch/Digital Out/ CD Lid/Washer (Combined Ass'y) — Power,Power Amp. (Combined Ass’y) AC CD Motor (PWB Only) — Tape Mechanism — Tape Mechanism SPEAKER BOX PARTS 701 702 703 704 705 706 707 708 709 SP601,602 SP603,604 J AZ CD Pickup Lens Cleaner Disc –6– GBOXS0003SJZZ HSY093SPK010 HSY093SPK020 HSY093SPK030 9GDHSY041SPK04 9GDHSY042SPK03 9GDHSY041SPK06 9GDHSY041SPK08 HSY093SPK040 PGUMM0001SJSB VSPA010PB054N RALMB0001SJZZ J J J J J J J J J J J J BF AK AH AK AG AH Speaker Ass’y,Left/Right Front Panel Ass’y Net Frame Ass’y Speaker Box Ass’y Spacer Board Duct Pipe Cord,Speaker Screw,ø4×16mm Label,Specifications Net Catcher Speaker,Woofer Speaker,Tweeter PACKING PARTS SPAKA0035SJZZ SPAKC0089SJZZ SPAKP0006SJZZ J J J SPAKZ0011SJZZ J SPAKZ0012SJZZ J 1 9GDHSY041SPK10 J 2 SPAKA0045SJZZ J Speaker Add. [Europe Only] Packing Case [Europe Only] Polyethylene Bag,Speaker [For Europe] Bottom Pad,Speaker [Europe Only] Center Pad,Speaker [Europe Only] AE Polyethylene Bag,Speaker [For U.K.] PackingAdd.,Top/Bottom, Speaker [U.K. Only] CP-XL70H SPEAKER BOX PARTS 701 702 703 704 705 706 707 708 709 710 711 712 SP601,602 SP603,604 HSY094SPK010 HSY094SPK020 9GDHSY042SPK03 PGUMM0002SJSA HDECQ0035SJSA 9GDHSY042SPK07 LX-MZ0003SJFN LX-MZ0002SJFN HSY094SPK030 9GDHSY042SPK09 9GDHSY041SPK06 9GDHSY042SPK05 VSPA010WB064N VSP00DMTB194N J J J J J J J J J J J J J J AP Net Frame Ass’y AK Speaker Box Ass’y AH Duct Pipe Net Catcher Ring,Woofer AG Capacitor,3.3 µF,50V Screw,ø4×20mm AH Screw,ø3×12mm AD Label,Specifications AG Absorber AK Speaker Cord A AG Speaker Cord B AX Speaker,Woofer AX Speaker,Tweeter SPAKA0035SJZZ SPAKC0089SJZZ SPAKP0006SJZZ J J J SPAKZ0011SJZZ J SPAKZ0012SJZZ J Speaker Add. [Europe Only] Packing Case [Europe Only] Polyethylene Bag,Speaker [For Europe] Bottom Pad,Speaker [Europe Only] Center Pad,Speaker [Europe Only] AE Polyethylene Bag,Speaker [For U.K.] Packing Add.,Top/Bottom, Speaker [U.K. Only] PACKING PARTS OTHER SERVICE PART UDSKA0004AFZZ DESCRIPTION CP-XL60H AC Power Supply Cord AM Loop Antenna FM Antenna Packing Add.,Top [For Europe Only] Packing Add.,Bottom [For Europe Only] Packing Add.,Side [For Europe Only] Packing Case [XL-60H] Packing Case [XL-70H] Polyethylene Bag,Unit [For Europe Only] Protection Sheet,Top/Bottom [For Europe Only] Polyethylene Bag,Accessories Operation Manual Label,Bar Code,Packing Case Label,Feature [XL-60H] Label,Feature [XL-70H] Label,Saving Energy [For Europe Only] Remote Control Battery Lid,Remote Control ACCESSORIES/PACKING PARTS (For U.K.) ! PRICE RANK PARTS CODE 1 9GDHSY041SPK10 J 2 SPAKA0047SJZZ J XL-60H/70H XL-60H/70H A 307 B 701 306 304 306-2 701 C 306-1 704 306-3 302 D 702 301 303 E 703x2 NM802 F 305 G NM801 305x2 NSW801 PWB-C H 1 2 3 4 Figure 7 CD MECHANISM EXPLODED VIEW –7– 5 6 XL-60H/70H XL-60H/70H 613 214 212 210 206 615x2 613 217 A 204 613 205 PWB-A9 613x2 613 PWB-A6 220 216 B 216-2 BELT CONNECTION Motor(M901) 216-1 601 616x5 FF/REW Clutch 603x2 PWB-A10 255 601 FF/REW Belt PWB- 601 A10 CD MECHANISM Main Belt Flywheel PWB-A10x3 601x3 PWB-A3 PWB-A7 253 610x2 PWB-A4 PWBA8 254 C PWB-A2 LCD701 257 241 603 601x2 234 233 252 M701 246 232 243 608x2 244 609x3 608x2 250 613x2 609x3 604 x2 256 251 240 247 D 605 610x2 PWB-A5 208 209 242 PWB-A8 609x3 605x2 201-3 222 601 613 231 201-5 201 M801 245 201-2 613 604 201-11 604 604x3 E 221 201-1 203 604 Q605 248 604 Q607 Q604 Silicon Grease TAPE MECHANISM 228 601 Silicon Grease 229 230 PWB-A1 F 249 617x4 612 201-7 201-9 601x4 604 PWB-B2 IC601 227x4 614x2 224 T681 219 613 604 226 201-4x2 614x2 237 (237-1,237-2,237-3,237-4(SOL901), 237-5,237-6,237-7(SW901), 237-8(SW902), 237-9(M901), 237-10(PWB-D), 237-11(PWB-E)) 201-12 G 201-13x2 201-8 PWB-B1 218 T651 201-6 201-10 611 223 225 201-13x2 H 612 238 613x2 Note: Only the unit and consumale parts are supplied as parts supply for the Tape mechanism. 1 2 3 4 Figure 8 CABINET EXPLODED VIEW –8– 5 6 XL-60H/70H CP-XL60H A TWEETER SP603(L-CH) SP604(R-CH) TWEETER SP603(L-CH) SP604(R-CH) BLACK RED WOOFER SP601(L-CH) SP602(R-CH) B BLACK WITH WHITE LINE BLACK WOOFER SP601(L-CH) SP602(R-CH) C 708 SP603(L-CH) SP604(R-CH) D 701 702 709x4 705 706 E 704 SP601(L-CH) SP602(R-CH) 703 F G 707x4 H 1 2 3 4 Figure 9 SPEAKER EXPLODED VIEW (1/2) –9– 5 6 XL-60H/70H CP-XL70H Capacitor (706) A TWEETER SP603(L-CH) SP604(R-CH) BK 711 B BK Black with White Line BK 712 Black with White Line WOOFER SP601(L-CH) SP602(R-CH) C 709 702 D 704x4 SP603(L-CH) SP604(R-CH) 703 706 708x4 E 710 SP601(L-CH) SP602(R-CH) F 701 TWEETER SP603(L-CH) SP604(R-CH) 706 Capacitor 3.3µF,50V G 705 707x4 WOOFER SP601(L-CH) SP602(R-CH) H 1 2 3 4 Figure 10 SPEAKER EXPLODED VIEW (2/2) – 10 – 5 6 XL-60H/70H PACKING OF METHOD (FOR U.K. ONLY) XL-60H/70H CP-XL60H 1. AC Power Supply Cord 2. AM Loop Antenna 3. FM Antenna 4. Remote Control 5. Packing Add., Left/Right 6. Packing Case [XL-60H] 6. Packing Case [XL-70H] 7. Polyethylene Sheet, Unit 8. Polyethylene Sheet, AC Power Supply Cord 9. Polyethylene Bag, Accessories 10. Operation Manual 11. Feature Label [XL-60H] 11. Feature Label [XL-70H] 12. Quick Guide 13. Bar Code Label, Packing Case 14. R-Card QACCB0001SJ00 QANTL0002SJZZ QANTW0002SJZZ RRMCG0014SJSB SPAKA0043SJZZ SPAKC0110SJZZ SPAKC0111SJZZ SPAKP0002SJZZ SPAKP0003SJZZ SSAKA0002SJZZ TiNSE0037SJZZ TLABM0022SJZZ TLABM0024SJZZ TiNSE0042SJZZ TLABE0054SJZZ TCADN0001SJZZ 1. Polyethylene Bag, Speaker 2. Packing Add., Top/Bottom, Speaker CP-XL70H 1. Polyethylene Bag, Speaker 2. Packing Add., Top/Bottom, Speaker 9GDHSY041SPK10 SPAKA0047SJZZ Setting position of switches and knobs Tape Mechanism STOP Cassette Holder CLOSE CD Lid CLOSE 1 7 9GDHSY041SPK10 SPAKA0045SJZZ 8 1 2 10 12 14 3 CP-XL60H CP-XL70H 9 4 Button Side XL-60H XL-70H 11 2 Front Left L Right Rear Front 2 R 5 13 6 COPYRIGHT © 2000 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any from or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. SHARP CORPORATION Communication Systems Group Quality & Reliability Control Center Higashihiroshima, Hiroshima 739-0192, Japan Printed in Japan A0004-2404DS•HA•C SG • SK • EX