Download here - Analogue Haven

Transcript
6:
[low/high] Distortion switch – selects between two separation-frequencies of the two-band
distortion module: low 96 Hz / high 1050 Hz
7:
[frequency] Frequency knob – adjusts cutoff frequency of VCF 1
8:
[resonance] Resonance knob – adjusts resonance of VCF 1
9:
[pedal] Knob with center position – adjusts positive/negative (ccw/cw) modulation amount
of a foot pedal, connected to socket 5, to cutoff frequency of VCF 1
10:
[depth] Knob with center position – adjusts positive/negative (ccw/cw) modulation amount
of envelope generator AHR 1 to cutoff frequency of VCF 1
11:
[env-mod1] Toggle switch – selects between the two sources AMT1 / DYN (external / dynamic) to control the modulation amount of AHR 1 – envelope to cutoff of VCF1, after passing
knob (10)
12:
[modulation] Knob with center position - adjusts positive/negative (ccw/cw) modulation
amount of the selected modulation source to resonance of VCF 1
13:
[reso-mod1] Toggle switch - selects between the two resonance-modulation sources for
VCF 1: S&H/ ENV 1
14:
[modulation] Knob with center position - adjusts positive/negative (ccw/cw) modulation
amount of the selected modulation source to cutoff frequency of VCF 1
15:
[vcf-mod1] 3-way switch –selects between three cutoff modulation sources for knob (14):
dynamic / LFO / S&H
16:
[curve] 12-position rotary switch – selects between 12 different characteristics of VCF 1:
24 db-LP, 18 db-LP, 2x12 db-LP, 2x6 db-LP, 6/6 db-BP, 12/6 db-BP, 6 db-HP, 12 db-HP, notch, inverse allpass
17:
[attack 1] Envelope knob – adjusts attack-time of envelope generator ENV 1
18:
[hold 1] Envelope knob – adjusts hold-time of envelope generator ENV 1
19:
[release 1] Envelope knob – adjusts release-time of envelope generator ENV 1
20:
[dynamic] Toggle switch – selects linear or logarithmic scaling (lin/log) of the follower-modulationsignal, which is derived from the incomming audiosignal at the compressor input.
21:
[gate] 3-way-switch – selects between three sources to trigger the gate of the S&H unit
(Sample & Hold): audiotrigger / LFO / external
22:
[source] 3-way-switch – selects between three input sources of the S&H unit
(Sample & Hold): dynamic / LFO / random (DYN / LFO / RAND)
23:
[wave] 3-way-switch –selects between three LFO waveforms: triangle / sawtooth (falling) /
rectangular
23a:
LED – displays the momentary level of the LFO-signal
24:
[speed] LFO-knob – adjusts the LFO-frequency
25:
[attack 2] Envelope knob – adjusts attack-time of envelope generator ENV 2
26:
[hold 2] Envelope knob – adjusts hold-time of envelope generator ENV 2
27:
[release 2] Envelope knob – adjusts release-time of envelope generator ENV 2
28:
[frequency] Frequency knob – adjusts cutoff frequency of VCF 2
29:
[resonance] Resonance knob – adjusts resonance of VCF 2
30:
[pedal] Knob with center position – adjusts positive/negative (ccw/cw) modulation amount
of a foot pedal, connected to socket 5, to cutoff frequency of VCF 2
l
13 user manual e b b e
und
flut