Download View User`s Manual
Transcript
® OWNER’S MANUAL HA1000 MIXER POWERED 10 INPUTS 2 X 500 WATTS BAL www.harbingerproaudio.com BUILT IN DSP BAL BAL BAL Welcome Thank you for your purchase of this Harbinger® Powered Mixer. It’s packed with quality features usually found only on larger, more expensive systems. To get the most from your new HA1000, take a moment and read through this entire manual to learn about all its important features. 2 Your new PA includes: • 2 x 500W output power with Stereo, Main/Monitor, or Bridge Mono operation • 6 Mic/Line inputs with XLR and ¼” input connectors, plus 12V phantom power • 4 Mic inputs with XLR and Dual ¼” input connectors • Built-in 24-bit DSP processor with 100 presets • Two 9-band Graphic Equalizers • Dual function FX/Aux send per channel • 3-band EQ per channel • Level control and bi-color Signal/Peak LED per channel • Stereo Output for recording, Stereo Input for CD/MP3 playback Monitor Send per channel Owner’s Manual for the HA1000 Powered Mixer Important Safety Instructions DANGER Exposure to extremely high noise levels may cause permanent hearing loss. Individuals vary considerably to noise-induced hearing loss but most will lose some hearing if exposed to intense noise for a sufficient period of time. The U.S. Government’s Occupational Safety and Health Administration (OSHA) has specified the following permissible noise level exposures: DURATION PER DAY (HOURS) 8 6 4 3 SOUND LEVEL (dB) 90 93 95 97 100 103 2 1 According to OSHA, any exposure in the above permissible limits could result in some hearing loss. Ear plugs or protectors in the ear canal or over the ears must be worn when operating this amplification system in order to prevent a permanent hearing loss. If exposure in excess of the limits as put forth above, to insure against potentially harmful exposure to high sound pressure levels, it is recommended that all persons exposed to equipment capable of inducing high sound pressure levels, such as this amplification system, be protected by hearing protectors while this unit is in operation. THIS SYMBOL IS INTENDED TO ALERT THE USER TO THE PRESENCE OF NON-INSULATED “DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS THIS SYMBOL IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE UNIT. APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING AND THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS. www.harbingerproaudio.com IMPORTANT SAFETY INSTRUCTIONS 1. Read all safety and operating instructions before using this product. 2. All safety and operating instructions should be kept for future reference. 3. Read and understand all warnings listed on the operating instructions. 4. Follow all operating instructions to operate this product. 5. This product should not be used near water, i.e. a bathtub, sink, swimming pool, wet basement, etc. 6. Use only a dry cloth to clean this product. 7. Do not block any ventilation openings. The product should not be placed flat against a wall or placed in a built-in enclosure that will impede the flow of cooling air. 8. Do not install this product near any heat sources, such as radiators, heat registers, stoves or any other apparatus (including heat–producing amplifiers) that produces heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord being walked on or pinched, particularly at plugs, convenience receptacles and the point where they exit from the apparatus. Do not break the ground pin of the power supply cord. 11. Only use attachments specified by the manufacturer. 12. When a cart is used, use caution when moving cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Care should be taken so that objects do not fall and liquids are not spilled into the unit through the ventilation ports or any other openings. 15. Refer all servicing to a qualified service professional. Servicing is required when the apparatus does not operate normally or has been damaged in any way, including damage to the power cord or plug, damage due to liquids spilled or objects dropped inside the unit, dropping the unit, or anything else that interrupts normal use of the unit. 16. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. 17. Protective Ground Terminal. The apparatus shall be connected to an AC main socket with a protective earth ground connection. 3 Table of Contents Welcome............................................................................... 2 Safety..................................................................................... 3 Basic Operation.................................................................... 4 Front and Rear Panel Diagram............................................ 5 Front Panel Connections....................................................... 6 Front Panel Controls............................................................. 7 Rear Panel Connections....................................................... 10 Specifications........................................................................ 11 Block Diagram...................................................................... 12 Warranty............................................................................... 13 Basic Operation • • • • 4 Ensure the HA1000’s power is turned off. Place the HA1000 on the floor, a table, or a sturdy stand. Turn down all Level, Monitor Level, and Main Level Controls. Plug speakers into the rear panel speaker jacks. NOTE: Speakers should be placed in a location that allows for unobstructed (line-of-sight) sound projection to the audience. In many venues, it is beneficial to place speakers on speaker stands for best results. • Plug sources such as microphones, instruments, or CD/MP3 players into the front panel jacks. • Turn AC Power switch to “On”. • Plug in all AC connections for sound system and sources. • Slowly turn the Main Level to 12 o’clock. • Slowly turn the Level control on each input Channel up to the desired volume level. Owner’s Manual for the HA1000 Powered Mixer Front And Rear Panel Diagrams 25 24 26 18 4 9 PEAK 10 HIGH 12KHz 11 MID 2.5KHz 12 LOW 80Hz PEAK HIGH 12KHz 15 00-09 10-19 20-29 30-39 40-49 50-59 60-69 70-79 80-89 90-99 HIGH 12KHz 15 15 PROGRAM 12 HA1000 14 CHANNEL • DSP • 2 X 500 WATTS PUSH TO SELECT 15 CLIP DSP 13 14 15 Vocal Small Room Large Hall Echo Echo + Verb Flange + Verb Plate Chorus + GTR Rotary + GTR Tremolo + GTR +15 +15 +9 +9 0 0 9 9 15 15 CLIP 19 0 10 1 0 20 30 63 PAN 123 250 500 1K 2K 4K 8K 10 LEVEL 16K MONITOR L 16 10 LEVEL 10 10 LEVEL 17 PAD +15 +15 +9 +9 R 0 0 9 9 R 15 15 LEVEL PAD PAD L CLIP 0 POWER - 10 21 22 - 30 10 LEVEL 63 OUT 123 250 500 1K 2K 4K 8K 16K MAIN STEREO IN/OUT LINE OUTS ON MIC IN MIC IN MIC IN MIC IN MIC IN MIC IN 1 2 4 5 78 7- 9-10 13 -14 2 MAIN R M BRIDGE 27 OFF MIC IN 1 MAIN L MAIN L+R BRIDGE 3 PHANTOM POWER 12V 4 23 AMPLIFIER ASSIGN 5 28 6 7 8 30 CHECK "AMPLIFIER ASSIGN" SWITCH ON FRONT PANEL SPEAKER OUTPUT LEFT/MAIN OUTPUT 1 1+ POS 1NEG AMPLIFIER ASSIGN MAIN L MAIN L+R BRIDGE MAIN R 14 CHANNEL • DSP • 2 X 500 WATTS MONITOR BRIDGE CLASS 2 WIRING AC INPUT: 120V~60Hz FUSE: T12AL AC250V RATED POWER CONSUMPTION: 1300W HA1000 BRIDGE OUTPUT BRIDGE MODE 1000W@ 8 OHM (8 OHM MIN. LOAD) 250W@ 8 OHM (4 OHM MIN. LOAD) C CLASS 2 WIRING US MADE IN CHINA 29 www.harbingerproaudio.com 5 Front Panel Connections 2 2 22 1 XLR Mic Input Jack Channel 1-14 Balanced. Appropriate for microphones, or direct connections from amplifiers or DI boxes. 1 1 11 3 3 33 2 +15 1 +9 3 1 2 MIC IN 3 IN MIC MIC IN IN MIC 0 +15 MIC IN 2 1 +9 +15 3 0 +9 MIC IN 2 2 ¼” Line Input Jack Channel 1-6 Balanced or Unbalanced. Appropriate for instrument or line level equipment connections. 1 9 0 6 6 6 6 15 123 63 63 15 9 MIC IN LINE IN 15 63 123 250 63 123 250 LINE IN 3 9 15 LINE3 IN MIC IN LINE IN LINE IN IN LINE LINE IN Dual ¼” Line Input Jack Channel 7-14 Balanced or Unbalanced. Appropriate for instrument or line level equipment connections. +15 +15 +15 +15 +9 +9 +9 +15+9 0 0 +9 0 0 9 9 0 9 9 15 9 15 15 15 LINE IN LINE IN LINE IN LINE IN LINE IN IN LINE LINE IN LINE IN +15 4 Stereo Out Unbalanced dual RCA outputs for connecting to MP3 recorders or computers. This connection has a fixed output that is fed from the MAIN output. L L L LLL L OUT L 5 R R 15 9 R IN IN IN IN IN IN L +9 +9 +9 +9 +9 0 +9 9 0 0 9 0 15 IN L LL LL +15 +15 +15 +9 0 +15 OUT OUT IN OUT OUT OUT OUT L +15 +15 +15+9 R R R RR R OUT L Stereo In Unbalanced inputs for CD/MP3 players. Use either the dual RCA jacks or the stereo 3.5mm mini jack. These inputs are controlled by the Stereo In Level control and are fed to the Main volume. R LINE IN 0 0 0 63 15 63 R 63 R R R RR 9 9250 15 15 15 123 15 15250 123 9 9 9 123 6 6 6 63 6 FOOTSWITCH FOOTSWITCH FOOTSWITCH 6 Footswitch DSP Mute Plug in a latching footswitch (not included) to turn the DSP Multi-FX on/off remotely. Useful to turn the FX off when talking, and back on when singing/playing. M MONITOR OUT MONITOR OUT MAIN OUT L MAIN OUT R MAIN OUT L FOOTSWITCH FOOTSWITCH FOOTSWITCH MAIN OUT L FOOTSWITCH FOOTSWITCH MONITOR OUT M MAIN OUT R MAIN OUT R PEAK PEAK 7 8 Monitor Out/Main Out Line level output controlled by the Monitor or Main Level knob to send the signal to external amplifiers or powered speakers. PEAK HIGH 12KHz MONITOR OUT HIGH MAIN OUT L MONITOR OUT MONITOR OUT MONITOR MONITOR OUT OUT MAIN OUT R 15 OUT 15L HIGH 12KHz MAIN MAIN OUT R MAIN OUT R MAIN MAIN OUT OUT R R MAIN 12KHz OUT L MAIN OUT15LL MAIN 15 OUT 15 MID 2.5KHz 15 PEAK 12 MID MID 2.5KHzPEAK 2.5KHz PEAK PEAK PEAK 12 12 12 12 12 HIGH LOW 80Hz 12KHz HIGH 15 LOW HIGH 80Hz 15 12KHz LOW HIGH HIGH 12KHz 80Hz 12KHz 15 12KHz MON 15 15 15 15 15 MON MID 12 MID 2.5KHz FX/AUX MID MID 2.5KHz POST 2.5KHz 2.5KHz 12 12 12 12 PAN PAN 6 MON 15 15 15 15 15 10 12 10 10 12 12 12 12 10 FX/AUX LOW POST 80Hz LOW PAN LOW 80Hz LOW LOW 80Hz 80Hz 80Hz 15 15 10 MID MON 2.5KHz FX/AUX POST 15 BAL 10 15 L R L R 15 15 15 15 15 L BAL L R L R 15BAL 15 15 15 R 10 LEVEL L R Owner’s Manual for the HA1000 Powered Mixer 10 10 MON MON LEVEL LLL R R R 63 FOOTSWITCH FOOTSWITCH FOOTSWITCH FOOTSWITCH FOOTSWITCH FOOTSWITCH Front Panel Controls MONITOR OUT MAIN MAIN OUT MAIN OUT MONITOR OUT OUT L L MAIN OUT RR MONITOR OUT MAIN OUT L MAIN OUT R MONITOR OUT MAIN OUT L MAIN OUT MONITOR OUT OUT MAIN OUT OUT LL MAIN OUT OUT R R MONITOR MAIN MAIN R 9 10 11 12 13 14 15 Signal/Peak LED This LED turns green when a signal is present in the Mic/Line input, and turns red when the input signal is clipping. If this occurs, lower the source signal output if possible. High EQ This is the treble control used to boost or cut high frequencies on the input channel, using a high shelf filter with +/- 15dB of boost or cut above 12kHz. Useful for adding clarity to vocals or acoustic guitars, or removing hiss or unwanted cymbal pick-up. Mid EQ This is the mid range control used to boost or cut mid frequencies on the input channel, using a bandfilter with +/- 12dB, centered at 2.5kHz. This range will affect vocals and most instruments. Low EQ This is the bass control used to boost or cut low frequencies on the input channel using a low shelf filter with +/- 15dB of boost or cut, below 80Hz. Useful for removing rumble on vocal or acoustic guitar inputs. MON Send This control sends the input signal to the Monitor Line Out jack and assigned Monitor power amp (speaker output #2 when MAIN L+R / Monitor is selected in the Amplifier Assign section). See “Amplifiers Assign Switch” on page 9. FX/Aux Send This control sends the input signal to the built-in DSP FX processor and the Aux Send jack in the master section. This controls the amount of FX used on each input channel. Pan Channel 1-6/Bal Channel 7-14 This control adjusts the balance of the input signal between the Left and Right outputs when the Amplifier Assign is MAIN L / MAIN R. See “Amplifiers Assign Switch” on page 9. PEAK PEAK PEAK PEAK PEAK PEAK HIGH HIGH 12KHz 12KHz HIGH HIGH HIGH 12KHz 1515 12KHz 12KHz HIGH 12KHz 15 15 15 15 15 15 15 MID MID 2.5KHz 2.5KHz MID MID MID 2.5KHz 1212 2.5KHz 2.5KHz MID 2.5KHz 12 12 12 12 LOW LOW 80Hz 80Hz LOW LOW LOW 1515 80Hz 80Hz 80Hz 15 1212 12 12 12 12 LOW 80Hz 1515 15 1515 15 15 15 15 15 15 15 MON MON MON MON MON MON 1010 10 10 10 10 FX/AUX FX/AUX POST POST FX/AUX FX/AUX FX/AUX POST POST POST FX/AUX POST 1010 10 10 10 10 PAN PAN PAN PAN PAN PAN L BAL BAL BAL L L BAL BAL BAL R R R L LL L R R R L L R R LL L R R R R 16 Channel Level This is the volume control for individual input channels. 1010 10 LEVEL LEVEL 10 LEVEL 10 10 LEVEL LEVEL LEVEL Input Pad Channel 1-6 17 Reduces the input signal by -20dB. Useful when the input signal is very strong and overdriving the input (causing the clip light to constantly flash or remain lit). PAD 10 LEVEL www.harbingerproaudio.com 1010 LEVEL LEVEL LEVEL LEVEL LEVEL 10 10 10 7 123 6 6 6 AMPLIFIER ASSIGN FX/AUX POST PEAK 10 DSP MULTI-FX 24-BIT PROCESSOR HIGH 12KHz PAN 15 BAL 15 L 18 2MIC IN1 0 +15 123 +9 9 123 250 R L 500 250 500 1K 2K 2K R R 9 63 250 500 1K 2K 8K 16K 9 15 15 123 63 123 250 250 500500 1K 2K 1K 2K4K 10 ON 8K 4K16K 8K 16K MAIN OUT L 10 LEVEL 63 MAIN OUT R 123 250 LINE IN OFF 2K MONITOR BRIDGE 500 1K 10 LEVEL POWER AMPLIFIER 4K +15 R +9 +9 OUT Phantom On/Off FOOTSWITCH IN This button is used when condenser microphones are connected to the HA1000, providing L R OUT applies MAIN OUT OUTconnections. R 12V to the XLR microphone inputs. Phantom MONITOR power only toL XLRMAIN input 10 15 12 PEAK 63 12 BRIDGE LOW 80Hz PEAK MAIN L+R BRIDGE MAIN OUT R 12 DSP DSP DSP 10 MULTI-FX MULTI-FX PROGRAM 24-BIT PROCESSOR 24-BIT PROCESSOR 15 12 CLIP MAIN R FX AUX to MAIN 10 HIGH FX/AUX 12KHz POST 15 BRIDGE MULTI-FX AMPLIFIER 24-BIT ASSIGN PROCESSOR 15 15 16K AMPLIFIER MONITOR BRIDGE ASSIGN 15 MAIN OUT L 9 15 MUTE MAIN L MON HIGH 12KHz 10 LEVEL DSP MUTE 15 HIGH PEAK 12KHz MAIN L+R LEVEL MONITOR ON BRIDGEPROGRAM BRIDGE OFF8K 123 250 500 1K 2K 4K PHANTOM MAIN L MAIN R AMPLIFIER POWER 12V MAIN L+R MONITOR ASSIGN PUSH TO SELECT MAIN OUT R MONITOR OUT 10 MAIN R MAIN L 15 FOOTSWITCH MAIN OUT L 0 MULTI-FX 24-BIT PROCESSOR 9 MID 2.5KHz LEVEL DSP 0 HIGH 12KHz 15 8K 10 LEVEL +15 PEAK L FX AUX to MON 15 10 PROGRAM MID PAN 2.5KHz 12 R MID 2.5KHz 10 PROGRAM BAL 12 L L R ON PUSHTO TO SELECT PUSH SELECT OFF DSP POWER MUTE LOW 80Hz 12 15 10 15 LEVEL 15 CLIP CLIP MUTE DSP MUTE PUSH TO SELECTMUTE Owner’s Manual for the HA1000 Powered Mixer ON MON OFF 10 10 LEVEL 9 15 MAIN R MAIN L+R BRIDGE ASSIGN FOOTSWITCH 15 15 0 LEVEL MAIN L MONITOR OUT 12 9 +9 0 15 Main Level This knob is used to control the overall output level delivered to the speakers. LOW 80Hz 4K 9 LINE IN R 8 +9 15 10 123 0 +15 +15 9 +9 15 0 63 +9 0 FX AUX to MON +15 9 1 FOOTSWITCH L +15 +15 +9 0 0 10 L LOW 80Hz 16K 10 +9 MIC IN MID 2.5KHz 8K 16K LEVEL +15 3 15 4K 8K 10 IN +15 Main 9-Band Graphic EQ L R L 9R Graphic Equalizer contains 9 filters that each cut or boost +/- 15dB around their center +9 IN frequency. These filters can be used to contour the overall sound of all inputs, and reduce 15 OUT 0 feedback (cut only). The EQ assign is the same as the Assign.RBAL PAN L Amplifier MONITOR OUT 15 10 +9 OUT 2 23 4K 15 9 10 LEVEL R POST 123 LEVEL 1K FX AUX LEVEL to MAIN +15 L FX/AUX LINE IN 22 16K 9 10 15 LINE IN IN 8K +9 0 LINE IN 10 Monitor Level This knob controls the output level of the Monitor Out jack. Each input Level control feeds both the Main Out (power amp) and Monitor Line Out. L 4K MUTE +15 LINE IN MON LINE IN 2K 0 63 21 1K 1 3 OUT 15 0 CLIP DSP 250 500 MUTE +15 MIC IN 20 9 +9 10 PUSH TO SELECT LEVEL LOW 63 Monitor 9-Band Graphic EQ 9 80Hz Graphic Equalizer contains 9 filters that each cut or boostMIC +/15dB around their center IN 15 15 15 IN of all inputs, and reduce frequency. These filters can be used to contour the overall LINE sound feedback (cut only). The EQ assign is the same as the Amplifier Assign. 63 2 R +15 15 0 3 19 L +9 +9 Stereo-In Level MID 2 1 2.5KHz This is the volume level for any devices connected to the CD/MP3 inputs using RCA0 or 3 +15 mini-plug. The sound from CD/MP3 IN goes directly to the MAIN Output. 12 12 9 +9 R PROGRAM +15 DSP MUTE FX AUX to MAIN PHANTOM POWER 12V 10 CLIP 16K IN FOOTSWITCH 15 L R MONITOR OUT MONITOR OUT MAIN L 63 MAIN OUT L FOOTSWITCH MAIN OUT R MAIN OUT L MAIN OUT R 123 MAIN L 00-09 Vocal 15 Reverb Delay Time: 0.8~15 0.9s; Pre-Delay: 0~45ms MID 10-19 Small Room Decay Time: 07~2.1s; Pre-Delay: 20~45ms 20-29 Large Hall Decay Time: 3.612KHz ~5.4s; Pre-Delay: 23~55ms +15 +9 PEAK 12 PUSH TO SELECT DSP PROGRAM MULTI-FX CLIP 24-BIT PROCESSOR DSP PUSH TO SELECT MUTE 2.5KHz 12 LOW MID 1452.5KHz 80Hz ~205s 15 2 1 12 30-39 Echo Delay Time: 40-49 Echo+Reverb Delay Time: 208~650ms; 15 Decay 15Time: 1.7 2.1s ~ 12 12 50-59 Flanger+Reverb Decay Time: 1.5~ 2.9ms; Rate: 0.8Hz~2.5Hz 80Hz 60-69 Plate Decay Time: 09sMID ~3.6s 70-79 Chorus+GTR Rate: 80-89 Rotary+GTR Modulation Depth: 20%~80% 15 2.5KHz MIC IN 0.92Hz~1.7Hz LOW MON 12 80Hz Speed 15 MON 15 DSPPROGRAM MUTE PUSH TO SELECTMUTE 9 63 123 FX AUX DSP to MAIN 10 BAL OUT R 63 LEVEL FX AUX to MAIN 10 FX AUX to MON ON 10 +9 10 0 FX POWER AUX to MON 123 250 500 1K POWER PAN BAL LEVEL Amplifiers Assign Switch The HA1000 features 2 separate 500-Watt amps L R L R 10 MAIN L – MAIN R 10 LEVEL FOOTSWITCH LEVEL • Stereo Mode • Output 1 is Left signal 10 • Output 2 is Right signal LEVEL • Monitor outputs to Monitor Out jack only 10 • 4Ω minimum speaker load per output LEVEL 10 MAIN L+R – MONITOR MONITOR OUT MAIN OUT L MAIN OUT R LEVEL • Dual Mono Mode • Output 1 is Main • Output 2 is Monitor • 4Ω minimum speaker load per output PEAK 10 LEVEL Bridge – Bridge • Amplifier 1 and 2 combine into a single, larger amplifier (Mono) •BridgeOutputistypicallyusedforsubwoofer,withMainandMonitorLineOutputsconnected HIGH to powered speakers 12KHz • 8Ω minimum speaker load www.harbingerproaudio.com 15 9 15 OFF 10 ON 2K 4K 8K 16K OFF 10 28 +15 OFF ON R 9 Power On/Off IN PAN BAL This switch turns the HA1000 on and off. When the HA1000 is10powered on, the blue 15 10 R Power LED will light. L L R L R 10 10 FX AUX to MON 0 L 10 LEVEL 10 27 16K MUTE 10 FX AUX to MON MAIN 10 L 8K CLIP MUTE MON FX to Main Level FX/AUX BAL This control sends a signal from the FX/Aux returnPAN to the Main speakers and +15 Main POST 10 L R Line Output. +9 L R L R FX/AUX POST 15 10 LINE IN FX to Monitor Level 15 15 This control sends a signal from the FX/Aux return to the Monitor10 speakers and Monitor 10 FX/AUX Line Output. PAN 9 DSP MUTE MUTE FX AUX 250 500 1K 2K 4K to MAINTO SELECT PUSH POST LINE IN 26 0 CLIP 15 10 15 +9 CLIP 15 12 +15 MUTE 0 3 LOW LOW 80Hz FX/AUX MON POST 25 PROGRAM 24-BIT PROCESSOR PARAMETER Tremelo-GTR 24-BIT PROCESSOR PROGRAM AMPLIFIER DSP ASSIGN MULTI-FX PRESET 90-99 MAIN L+R DSP MONITOR BRIDGE BRIDGE MULTI-FX 15 NO. HIGH MAIN R MULTI-FX AMPLIFIER 24-BIT MAIN L PROCESSOR ASSIGNMAIN R DSP Program 15 This knob is used to select the 100 preset FX programs from the15 built-in 24-bit DSP FX HIGH PEAK MONITOR OUT MAIN OUT L MAIN OUT R processer. Turn the knob to the desired FX preset, then 12KHz push the knob to select the effect. 12 LEVEL DSP MAIN OUT R PEAK 15 16K 10 MAIN L+AMPLIFIER R MONITOR LEVEL BRIDGE BRIDGEASSIGN MAIN OUT L MID HIGH 2.5KHz 12KHz 8K MAIN R ASSIGN HIGH 12KHz DSP 24-BIT FX PRESET TABLE MONITOR 2K 4K BRIDGE 10 MAIN L FOOTSWITCH 24 1K 15 MAIN R MAIN L+R MONITOR AMPLIFIER BRIDGE BRIDGE PEAK MONITOR OUT LEVEL MAIN L+R 250 BRIDGE 500 ON POWER OFF ON PHANTOM 10 ON POWER 12V LEVEL OFFOFF PHANTOM POWER POWER 12V MAINON R OFF MONITOR MAIN L MAIN L+R BRIDGE BRIDGE PHANTOM POWER 12V AMPLIFIER ASSIGN ON OFF PHANTOM POWER 12V DSP MULTI-FX 24-BIT PROCESSOR 9 15 PROGRAM Rear Panel Connections AC INPUT: 120V~60Hz FUSE: T12AL AC250V RATED POWER CONSUMPTION: 1300W 29 AC Power Cord Input This is the AC Mains connection. Use only the supplied IEC cable or a UL listed replacement IEC Cable and 120V/60Hz AC outlet. SPEAKER OUTPUT 30 Speaker Outputs L/Main Connect up to two (2) loudspeakers to the speaker output jacks. Note that the HA1000 power amp is rated at 4Ω Minimum Load. You Y may safely connect 2 x 8Ω speakers or 1 x 4Ω speaker. L / MAIN 500W@ 4 OHM 250W@ 8 OHM (4 OHM MIN. LOAD) CLASS 2 WIRING BRIDGE OUTPUT Bridge Output (Mono) Connect one (1) 8Ω speaker to this output. Note that damage may occur to the HA1000 if using Bridge Mode with more than one 8Ω speaker. BRIDGE MODE 1000W@ 8 OHM (8 OHM MIN. LOAD) R/Monitor Connect up to two (2) loudspeakers to the speaker output jacks. Note that the HA1000 power amp is rated at 4Ω Minimum Load. You Y may safely connect 2 x 8Ω speakers or 1 x 4Ω speaker. Note: Twist-lock outputs are configured 1+ (pos)/1- (neg). CLASS 2 WIRING SPEAKER OUTPUT R /MONITOR 500W@ 4 OHM 250W@ 8 OHM (4 OHM MIN. LOAD) CLASS 2 WIRING CHECK "AMPLIFIER ASSIGN" SWITCH ON FRONT PANEL AMPLIFIER ASSIGN MAIN R L MONITOR MAIN L+R BRIDGE 10 Owner’s Manual for the HA1000 Powered Mixer Specifications Power Amplifier (Output): Input Channels Impedance Equalization DSP section (2x) 500 Watts Microphone Inputs Electronically balanced, discrete input Frequency Response 20Hz to 20kHz, ±3dB Gain 50dB Line Inputs Electronically balanced Frequency Response 20Hz to 20kHz, ± 3dB Gain 20dB Microphone Input 1.5kΩ All Other Inputs 10kΩ or greater Tape Out 1kΩ All Other Outputs 120Ω High Shelving ±15dB@12kHz Mid Shelving ±[email protected] Low Shelving ±15dB@80Hz Graphic EQ (2x) 9-band, 4/3 Octave A/D and D/A Converters 24-Bit DSP Resolution 24-Bit Type of Effects Vocal, Small Room, Large Hall, Echo, Echo+Reverb, Flanger+Reverb, Plate, Chorus+GTR, Rotary+GTR Main Mix Section Presets 100 Controls 100-position selector, Clip LED, Mute Switch with LED indicator Noise (Bus noise) Fader 0dB, channels muted = -85dBr (ref: +4dBu) Fader 0dB, all input channels assigned and set to Unity Gain = -81dBr (ref: +4dBu) www.harbingerproaudio.com Monitor Max Out +22dBu unbalanced, 1/4” jacks FX Sends Max Out +22dBu unbalanced, 1/4" jacks Total Harmonic Distortion < 0.5% @ 1 Watt output power; < 1% @ 300 Watt output Signal to Noise Ratio Output line to 1kHz = >65dB Static Power Consumption No output power state at 230V = < 50 Watts Power Source 110~127V/60Hz 11 A B C 1 STEREO IN LINE IN R LINE IN L MIC IN PHANTOM POWER +12V 3c 4d 2b 1a LINE IN 5e 3c 4d 2b 1a 5e 3c 4d 2b 1a 2 3 1 5e 2 3 1 2 PAD +16dB=OL(GLOW) PEAK SIG 3-STAGE EQ LOW MID HI 3-STAGE EQ +16dB=OL(GLOW) PEAK SIG 3-STAGE EQ 3 LEVEL MON LEVEL LEVEL MON BA BA BA BA BA FX/AUX FX/AUX PAN BAL 4 RIGHT LEFT MON FX/AUX RIGHT LEFT MON FX/AUX RIGHT FX/AUX RIGHT LEFT MON MON RIGHT LEFT IN DSP FX TO MAIN FX TO MON SUM SUM SUM 5 100Hz 100Hz 50Hz 50Hz OUT 6 6 STEREO 9-STAGE EQ INV MONO 9-STAGE EQ MAIN L MAIN R MONITOR 5KHz 5KHz STEREO 9-STAGE EQ 250Hz 250Hz LEFT 500Hz 500Hz LEVEL 5 8KHz 8KHz 4 16KHz 16KHz LOW MID HI 3 1KHz 1KHz LEFT BUS RIGHT BUS MON BUS FX/AUX BUS LEFT BUS RIGHT BUS MON BUS FX/AUX BUS 2.5KHz 2.5KHz MIC IN - + PHANTOM POWER +12V - D 2 DSP SELECT - 1 DSP MUTE 4 3 2 4 3 2 BA BA BA 1 1 7 STEREO AMPLIFIER AMPLIFIER ASSIGN LEVEL LEVEL LEVEL 8 1- 1- 1- 5e 3c 4d 2b 1a 5e 3c 4d 2b 1a SPEAKER OUTPUT BRIDGE SPEAKER OUTPUT RIGHT/MONITOR 2- 2- 8 DSP FOOTSWITCH SPEAKER OUTPUT LEFT/MAIN MONITOR OUT LINE OUT R LINE OUT L 2- LED METERS ( 4 POINT ) 5e 3c 4d 2b 1a LED METERS ( 4 POINT ) 5e 3c 4d 2b 1a HA1000 _ BLOCK DIAGRAM 7 1+ 1+ 2+ 2+ 1+ 2+ + - + + + - + 12 Owner’s Manual for the HA1000 Powered Mixer A B C D Warranty So we may serve you better, please register on-line at www.HarbingerProAudio.com 2 Harbinger Limited Warranty Harbinger provides to the original purchaser a two (2) year limited warranty on materials and workmanship on all Harbinger cabinets and loudspeaker components from the date of purchase. If your covered product is defective, ship the defective component together with proof of purchase — freight prepaid and insured— to an Authorized Harbinger repair center. Please contact Harbinger Support Headquarters for assistance at [email protected], or visit www.HarbingerProAudio.com. A Return Authorization Number must be obtained from our Customer Service Department prior to shipping the product. TolocatearepaircenternearyouandtoobtainaReturnAuthorization Number, contact [email protected] or visit www.HarbingerProAudio.com. S UNDENGINEERING www.harbingerproaudio.com This warranty does not cover service or parts to repair damage caused by neglect, abuse, normal wear and tear and cosmetic appearance to the cabinetry not directly attributed to defects in materials or workmanship. Also excluded from coverage are damages caused directly or indirectly due to any service, repair(s), or modifications of the cabinet, which have not been authorized or approved by Harbinger. This two (2) year warranty does not cover service or parts to repair damage caused by accident, disaster, misuse, abuse, burnt voice-coils, over-powering, negligence, inadequate packing or inadequate shipping procedures. The sole and exclusive remedy of the foregoing limited warranty shall be limited to the repair or replacement of any defective or non-conforming component. All warranties including, but not limited to, the express warranty and the implied warranties of merchantability and fitness for a particular purpose are limited to the two (2) year warranty period. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. There are no express warranties beyond those stated here. In the event that applicable law does not allow the limitation of the duration of the implied warranties to the warranty period, then the duration of the implied warranties shall be limited to as long as is provided by applicable law. No warranties apply after that period. www.harbingerproaudio.com Retailer and manufacturer shall not be liable for damages based upon inconvenience, loss of use of product, loss of time, interrupted operation or commercial loss or any other incidental or consequential damages including but not limited to lost profits, downtime, goodwill, damage to or replacement of equipment and property, and any costs of recovering, reprogramming, or reproducing any program or data stored in equipment that is used with Harbinger products. This guarantee gives you specific legal rights. You Y may have other legal rights, which vary from state to state. Harbinger, P.O. Box 5111, Thousand Oaks, CA 91359-5111 All trademarks and registered trademarks mentioned herein are recognized as the property of their respective holders. Made in China 1110-9638 13