Download Total Eclipse Manual

TOTAL ECLIPSE Operator Menus
Operator Main Menu
!
HYDRO
F01 PADS
Power Save Note
If the controller is idle (no key presses or cycle activity) for 15 seconds, the display
reverts to the Home Screen. If the controller is idle for 15 minutes, the Power Saver
feature shuts off the display backlight. Pressing any key returns the controller to
normal operation.
From the Home Screen, press any ARROW (except EXIT) to reach the MAIN MENU.
In the MAIN MENU, the operator can: Activate the emergency pump stop; Input
load size (if different from default); Prime pumps or manually flush (if enabled);
Print Manager Reports (password protected); and access the password-protected
INSTALLER MENU, which includes programming, setup and maintenance menus.
Emergency Pump Stop
Stops all pumps and cancels the formula currently running.
a. From the HOME SCREEN, press ENTER twice to reach
EMERGENCY STOP.
b.At the EMERGENCY STOP menu, press ENTER to stop all pumps and
formulas or press EXIT to return to the MAIN MENU.
Change Load Size/Weight
For accurate data reporting, the operator should input the actual weight of each
load, which overrides the default weight for that formula for a single load.
a.From the MAIN MENU, move selection box to LOAD SIZE and press ENTER.
The LOAD WEIGHT input screen displays the default weight for that formula.
, by
b. Change the active digit, indicated by the double-arrow cursor pressing the UP or DOWN ARROWS.
c.To move to the next digit, press the RIGHT ARROW. Set all digits.
d.
When the correct load weight displays, press ENTER to save.
To exit without saving changes, press EXIT .
User Prime Pumps (if enabled)
USER PRIME PUMPS allows the operator to fill the intake tube after product pail
or tube change. An animated progress bar indicates that prime is running. In a
non-flush system, the display is black bars on a white background. In a flushenabled sys­tem, the display is white bars on a black background.
If User Prime is set to ENABLE, the operator must stop Prime. If the operator fails
to stop Prime, it will stop after 10 minutes of keyboard inactivity. If User Prime is
set to LIMITED (30 SEC), each pump can be primed for a total 30 seconds and the
same pump cannot be primed again until a complete formula has run.
a.From the MAIN MENU, move the selection box to USER PRIME PUMPS
and press ENTER. The SET PRIME PUMP menu displays a list of available
pumps (with names, if previously input or uploaded by the installer). If User
Prime is not enabled in the Installer Menu, “DISABLED” displays (as the
default setting).
b. Press the UP or DOWN ARROW to choose a pump to prime.
c.Press ENTER to reach the PRIME menu for the chosen pump.
d.Press ENTER to start prime.
e.Press ENTER again to stop prime.
f. Press EXIT one time to select another pump to prime, or twice to return
to the MAIN MENU.
P/N 20-09120-00 Rev. C
© Hydro Systems Company, Inc. 2014
HydroSystemsCo.com
1 2 3 4 5 6
_ _ _ _ 5 _
MAIN MENU
EMERGENCY PUMP STOP
LOAD SIZE 075 LB
USER PRIME PUMPS
USER MANUAL FLUSH
MANAGER REPORTS
INSTALLER MENU
VIEW LOAD COUNT
EMERGENCY STOP
STOP ALL PUMPS
AND FORMULAS
STOP
EXIT
LOAD WEIGHT
2 LBS [KG]
SINGLE LOAD
STOP
EXIT
MAIN MENU
EMERGENCY PUMP STOP
LOAD SIZE 075 LB
USER PRIME PUMPS
USER MANUAL FLUSH
MANAGER REPORTS
INSTALLER MENU
VIEW LOAD COUNT
SET PRIME PUMP
P1PRE-WASH
P2DETERGENT
P3 LIQUID BLEACH
P4 BLEACH ALTERNATIVE
P5SOUR/CONDITIONER
P6 ENZYME LIFT
PRIME
P5 SOUR/CONDITIONER
STOP
Toll Free: 1.800.543.7184
EXIT
18