Download 506E Headphone Amplifier

Transcript
506E Headphone Amplifier
U
S
E
R
N
G
U
I
D
E
506E Headphone Amplifier
User’s Guide
© August 2000 Symetrix, Inc.
All rights reserved.
Printed in the United States of America
Symetrix Part Number 53506E-0A00
The information in this guide is subject to
change without notice. Symetrix, Inc. shall
not be liable for technical or editorial
errors or omissions contained herein; nor
is it liable for incidental or consequential
damages resulting from the furnishing,
performance, or use of this material.
Mention of third-party products is for informational purposes only and constitutes
neither an endorsement nor a recommendation. Symetrix assumes no responsibility with regard to the performance or use
of these products.
Under copyright laws, no part of this user
guide may be reproduced or transmitted
in any form or by any means, electronic or
mechanical, without permission in writing
from Symetrix, Inc. If, however, your only
means of access is electronic, permission
to print one copy is hereby granted.
Permission to copy the Architects and
Engineers Specificiations for written
proposals specifying equipment for sound
reinforcement systems is, also, granted.
Symetrix, Inc.
14926 35th Ave West
Lynnwood WA 98037-2303
USA
Tel:
425.787.3222
Fax:
425.787.3211
Web:
www.symetrixaudio.com
Email: [email protected]
Symetrix 506E Headphone Amplifier User’s Guide
Contents
Before You Begin
2
Rear Panel Overview
11
What Ships in the Box
2
Getting Help
2
Signal Flow Diagram
13
Optional Accessories
2
Notational Conventions in this User Guide
2
Troubleshooting
14
Operational Safety Summary
3
Equipment Markings
3
Hardware Specifications
15
506E Product Information
4
Architects and Engineers Specifications
16
Product Summary
4
Features
4
Warranty
17
Fast First-Time Setup
5
Service
18
Where to Get Service
18
Making Hardware Connections and Selections
5
In-Warranty Repairs
18
Setting Gain Controls
6
Out-of-Warranty Repairs
18
Calculating the Maximum Amplifier Load
7
To Get Your 506E Unit Repaired (US Customers Only)
18
If You Don't Have Factory Packaging Materials
18
Declaration of Conformity
19
Controlling the Volume Level from
a Remote Control
8
Front Panel Overview
9
1
Symetrix 506E Headphone Amplifier User’s Guide
Before You Begin
| What Ships in the Box | Getting Help | Optional Accessories
| Notational Conventions in this User Guide | Operator Safety Summary | Equipment Markings
What Ships in the Box
Getting Help
The 506E unit
IEC power cord
If you have technical questions beyond the scope of this guide, please contact
our Technical Services Group in the following ways:
Two 3.5 mm to 1/4" mini jack
adapters
4 rubber feet for mounting to
bottom of unit
This user's guide
A warranty card (if purchased in
USA)
T
US customers (888) 349-3222
International customers (425) 787-3222
from 6:00 am to 4:30 pm Pacific Time Monday through Friday
F
(425) 787-3211
[email protected]
www.symetrixaudio.com
You can register online at
www.symetrixaudio.com
When you register the 506E, you
get 4 extra years of warranty
coverage.
Optional Accessories
MODEL
ITEM
DESCRIPTION
HR-1
Headphone Remote
Stereo headphone jack with individual
volume control, input and output jacks,
various mounting options
USC-1
Security Cover
Fits 1U (19 in. x 1.72 in.) products
Contact your dealer or Symetrix for purchasing information.
Notational Conventions in this User Guide
Note
Identifies information that needs extra emphasis. Generally
supplies extra information to help you to better use the 506E.
CAUTION
Identifies information that, if unheeded, may cause damage to
the 506E or other equipment in your system.
WARNING
Identifies information that, if ignored, may be hazardous to
your health or that of others.
CAPS
Controls, switches or other markings on the chassis of the
506E.
2
Symetrix 506E Headphone Amplifier User’s Guide
Before You Begin
| What Ships in the Box | Getting Help | Optional Accessories
| Notational Conventions in this User Guide | Operator Safety Summary | Equipment Markings
Operator Safety Summary
Follow all warnings and instructions. Install
in accordance with the manufacturer’s
instructions.
Power Source This product is intended
to operate from a power source that does
not apply more than 120V rms between
the power supply conductors or between
either power supply conductor or ground.
Grounding The chassis of this product is
grounded through the grounding conductor of the power cord. To avoid electric
shock, plug the power cord into a properly
wired receptacle before making any
connections to the product. A protective
ground connection, by way of the grounding conductor in the power cord, is
essential for safe operation. Do not defeat
the safety purpose of the grounding
plug. The grounding plug has two blades
and a third grounding prong. The third
prong is provided for your safety. When
the provided plug does not fit your outlet,
consult an electrician for replacement of
the obsolete outlet.
Danger from Loss of Ground If the
protective ground connection is lost, all
accessible conductive parts, including
knobs and controls that may appear to be
insulated, can render an electric shock.
Proper Power Cord Use only the power
cord and connector specified for the
product and your operating locale. Use
only a cord that is in good condition.
Protect the power cord from being walked
on or pinched, particularly at the plug,
convenience receptacle, and the point
where the cord exits from the apparatus.
Equipment Markings
Operating Location Do not operate this
equipment under any of the following
conditions: explosive atmospheres, in wet
locations, in inclement weather, improper
or unknown AC mains voltage, or if
improperly fused. Do not install near any
heat source such as radiators, heat
registers, stoves, or other apparatus
(including amplifiers) that produce heat.
Unplug this apparatus during lightning
storms or when unused for long periods of
time.
Stay Out of the Box To avoid personal
injury (or worse), do not remove the
product covers or panels. Do not operate
the product without the covers and panels
properly installed. Only use accessories
specified by the manufacturer. Clean only
with a damp cloth.
User-serviceable parts There are no
user serviceable parts inside the 506E. In
case of failure, refer all servicing to the
factory. Servicing is required when the
506E has been damaged in any way, such
as when a power supply cord or plug is
damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:
AVIS:
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR MOISTURE
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
SEE OWNERS MANUAL. VOIR CAHIER D’INSTRUCTIONS.
No user serviceable parts inside. Refer servicing to qualified service personnel.
Il ne se trouve a l’interieur aucune piece pourvant entre reparée l’usager.
S’adresser a un reparateur compétent.
The lightning flash with arrowhead symbol
within an equilateral triangle is intended
to alert the user of the presence of
uninsulated “dangerous voltage” within
the product’s enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons. The exclamation
point within an equilateral triangle is
intended to alert the user of the presence
of important operating and maintenance
(servicing) instructions in the literature
accompanying the product (i.e., this user
guide).
CAUTION
To prevent electric shock, do not use the
polarized plug supplied with the unit
with any extension cord, receptacle, or
other outlet unless the blades can be
fully inserted.
3
Symetrix 506E Headphone Amplifier User’s Guide
506E Product Information
| Product Summary | Features
Product Summary
The 506E Headphone Amplifier contains
6 discrete headphone amplifiers, which
Features
Proprietary High Voltage
Drive Technology
Drives multiple headphones of any
impedance greater than or equal to
8 ohms with the equivalent output
voltage of a much larger power
amplifier.
6 Stereo Outputs
Automatically adjusts output power
to match the load impedance. Can
be used as a one-input, 6-output
headphone amplifier or as 6 headphone amplifiers.
Unique Mono Cue Input
For feeding a mix minus or IFB from
a producer or remote talent into the
main monitor mix during a live
broadcast, or for feeding a click
track during a recording session.
Assignable to left, center (left and
right), or right.
Mono/Stereo Switch
Maintains stereo signal integrity
from input to output or, in mono
position, either or both program
inputs may be used to provide mono
program signal.
Direct Input/Output and
Level Control
Allows you to interrupt the program/
cue input on each amplifier channel
and to insert a separate signal to
drive that amplifier channel independently from the other channels. Gain
controls are provided for program
and cue inputs and for the 6 output
amplifier channels.
Internal Power Supply
No “wallwart” or “lump-in-the-line.”
Optional Headphone Remote Box
Same 6 headphone outputs are also
provided at the rear panel to provide
output to the Symetrix HR-1 Headphone Remote.
are normally driven by a stereo
program input. Each amplifier has an
independent level control. The PROGRAM INPUT section also has a level
control and STEREO/MONO switch. The
CUE INPUT section has a level control
and Left/Center/Right ASSIGN switch.
4
Symetrix 506E Headphone Amplifier User’s Guide
Fast First-Time Setup
| Making Hardware Connections and Selections | Setting Gain Controls
| Calculating the Maximum Amplifier Load
Making Hardware Connections and Selections
506E Rear Panel
1
Plug the IEC power cord into the 506E and into the
appropriate source of AC power as indicated on the
rear panel.
OUTPUT
506E
HEADPHONE
AMPLIFIER
OUTPUT
DIRECT
INPUT
6
OUTPUT
DIRECT
INPUT
5
DIRECT
INPUT
OUTPUT
4
OUTPUT
DIRECT
INPUT
3
OUTPUT
DIRECT
INPUT
2
DIRECT
INPUT
CUE INPUT
PROGRAM
MONO
1
RIGHT
AC INPUT 25 WATTS MAXIMUM
506E Front Panel
2
Set all levels—PROGRAM INPUT, CUE INPUT, and all
6 headphones—to zero.
PROGRAM INPUT
4 5 6
3
2
CLIP 1
7
8
9
0
10
CUE INPUT
MONO
STEREO
OUTPUTS
1
4 5 6
ASSIGN
L
C
R
3
2
CLIP 1
7
8
9
0
3
2
SIGNAL 1
10
2
4 5 6
7
8
9
0
10
7
4
3
3
4 5 6
3
2
SIGNAL 1
7
8
9
0
10
4
4 5 6
3
2
SIGNAL 1
7
8
9
0
10
5
4 5 6
3
2
SIGNAL 1
7
8
9
0
3
2
SIGNAL 1
10
4 5 6
7
8
9
0
10
6
3
2
SIGNAL 1
4 5 6
7
8
9
0
10
POWER
Connect the first set of headphones either here or to
the rear panel OUTPUT 1 jack.
Set CUE INPUT ASSIGN switch to C (center).
If your program source is mono, press switch to
lower position.
If stereo, leave in forward position.
5
506E Rear Panel
OUTPUT
DIRECT
INPUT
6
OUTPUT
DIRECT
INPUT
5
OUTPUT
DIRECT
INPUT
4
OUTPUT
DIRECT
INPUT
3
OUTPUT
DIRECT
INPUT
2
(Optional)
Connect
your cue
source.
OUTPUT
DIRECT
INPUT
1
7
6
Connect your program source.
If your source is mono, connect
either to the left or right jack.
CUE INPUT
MONO
PROGRAM INPUTS
RIGHT
LEFT
Connect the first set of headphones either here or to
the front panel OUTPUT 1 jack.
5
Symetrix 506E Headphone Amplifier User’s Guide
Fast First-Time Setup
| Making Hardware Connections and Selections | Setting Gain Controls
| Calculating the Maximum Amplifier Load
Setting Gain Controls
1
While sending signal from your
program source, slowly turn the
PROGRAM INPUT level control
clockwise until the CLIP LED
flashes. Then back it off until
the CLIP LED does not flash, or
only flashes occasionally on
peaks in the program source.
506E Front Panel
PROGRAM INPUT
4 5 6
3
2
CLIP 1
2
7
8
9
0
10
CUE INPUT
MONO
STEREO
OUTPUTS
4 5 6
ASSIGN
L
C
R
3
2
CLIP 1
7
8
9
0
10
1
3
2
SIGNAL 1
2
4 5 6
7
8
9
0
While sending signal from your
cue source, slowly turn the CUE
INPUT level control clockwise
until the CLIP LED flashes. Then
back it off until the CLIP LED
does not flash, or only flashes
occasionally on peaks in the cue
source.
3
2
SIGNAL 1
10
3
4 5 6
7
8
9
0
10
3
3
2
SIGNAL 1
4 5 6
7
8
9
0
10
4
3
2
SIGNAL 1
While sending signal from your
program and/or cue source,
slowly turn the Channel 1 level
control clockwise until the green
SIGNAL LED lights. You should
be able to hear program and/or
cue signal in your first set of
headphones now.
4 5 6
7
8
9
0
10
5
3
2
SIGNAL 1
4 5 6
7
8
9
0
10
6
3
2
SIGNAL 1
4 5 6
7
8
9
0
10
POWER
4
Adjust the Channel 1 level
control for the desired listening
level.
5
If you are using program and
cue signals, adjust the PROGRAM INPUT and CUE INPUT
level controls to achieve the
desired balance of program to
cue signal.
6
Repeat steps for any additional
headphone sets, using channels
2–6 of the 506E. See in this
section, Calculating the Maximum Amplifier Load, to find out
how many headphones of
various impedances may be
used with each output of the
506E.
6
Symetrix 506E Headphone Amplifier User’s Guide
Fast First-Time Setup
| Making Hardware Connections and Selections | Setting Gain Controls
| Calculating the Maximum Amplifier Load
Calculating the Maximum Amplifier Load
The minimum operating impedance,
or maximum load, for each output of
the 506E is 8 ohms. Use as many
pairs of headphones as desired, as
long as the total combined impedance
(per output) does not fall below 8 ohms.
How Many Headphones of Various Impedances May Be Used
With Each Output of the 506E
IMPEDANCE OF HEADPHONES
MAXIMUM NUMBER/CHANNEL
8
1
16
2
32
4
100
10
200
20
400
40
600
60
If You Are Driving Low Impedance Headphones
If You Are Using Headphones
Spec’d for 8 Ohms Output
The quantities noted above reflect
usage with typical wide-range musical
signals. If you are driving lowimpedance headphones (16 ohms or
lower actual impedance), and you
intend to drive them to the brink of
amplifier clipping, then you should
revise the number of headphones
possible to 2 headphones at 8 ohms
or 4 headphones at 16 ohms. In the
example of 8 ohms, you’ll have 2
amplifier channels that aren’t doing
anything. It is OK to use any remaining amplifier channels with higher
impedance phones (50 ohms or
higher).
Many headphones are spec’d as being
suitable for 8 ohm outputs. They are,
but this does not mean that their
actual impedance is 8 ohms. In most
cases, the actual impedance is
substantially higher. This is good
(rather than bad). For whatever it’s
worth, most decent headphones have
actual impedances ranging from
50 ohms and up.
For maximum output with all channels driven, try to restrict the lowest
combined load impedance to 50 ohms
per channel. Lower impedance loads
simply reduce the maximum output
possible.
If You Are Using Multiple
Headphones
When multiple headphones are
required with each output, use
headphone type “Y” cords, or a
“breakout box,” such as the Symetrix
HR-1 Headphone Remote. A breakout
box may have as many paralleled
1/4" stereo jacks as necessary, as
long as the total combined impedance
(per output) does not fall below
8 ohms.
CAUTION
The 506E is capable of driving many
headphones past the threshold of
pain. At this volume level, hearing
damage can occur. For your own
hearing health, monitor at a low
sound pressure level.
7
Symetrix 506E Headphone Amplifier User’s Guide
Controlling the Volume Level from
a Remote Control
Using the Symetrix HR-1 Headphone Remote
The HR-1 Headphone Remote is
designed for use with the 506E unit
and is available for separate purchase.
The HR-1 allows you to make headphone amp outputs available at a
remote location. It also provides level
control for an individual output as
well as a Loop Through Output. This
output provides line level audio that
is not affected by the HR-1’s gain
control.
MANUFACTURED IN THE USA BY
LYNNWOOD, WA
NO USER SERVICEABLE PARTS INSIDE.
Output
Input
HR-1
Remote Control 2
4
For figuring headphone impedances,
see in this section Calculating the
Maximum Amplifier Load. Include in
your calculations both headphones
connected to the 506E’s front panel
jacks and headphones connected to
the corresponding HR-1 jacks. Minimum impedance is 8 ohms for 506E’s
headphone outputs.
Turn volume
control up to the
desired sound
level.
MANUFACTURED IN THE USA BY
HR-1
LYNNWOOD, WA
NO USER SERVICEABLE PARTS INSIDE.
Output
Input
Volume
HR-1
Remote Control 1
The HR-1 Has A Variety of
Mounting Options
3
Either recessed, extruded or flush
mounted into studio console furniture.
(Optional) Connect multiple HR-1s
with 1/4" TRS to TRS cables.
Attached to the top or underside of a
desk or cabinet.
Mounted on a microphone stand.
1
2
Connect a 1/4" TRS to TRS
(tip-ring-sleeve) cable,
maximum length 200 ft.
Set gain controls for
• PROGRAM INPUT
• CUE INPUT (if using cue)
PROGRAM INPUT
4 5 6
CLIP
3
2
1
7
8
9
0
10
• Headphone OUTPUT where
you have connected the HR-1.
CUE INPUT
MONO
STEREO
OUTPUTS
4 5 6
ASSIGN
L
C
R
CLIP
3
2
1
7
8
9
0
506E Front Panel
10
1
3
2
SIGNAL 1
4 5 6
7
8
9
0
10
2
3
2
SIGNAL 1
4 5 6
7
8
9
0
10
3
3
2
SIGNAL 1
4
4 5 6
7
8
9
0
3
2
SIGNAL 1
10
8
4 5 6
7
8
9
0
10
5
3
2
SIGNAL 1
4 5 6
7
8
9
0
10
6
3
2
SIGNAL 1
4 5 6
7
8
9
0
10
POWER
Symetrix 506E Headphone Amplifier User’s Guide
Front Panel Overview
PROGRAM INPUT
4
506 E
HEADPHONE
AMPLIFIER
5
6
3
7
2
CLIP
8
1
9
0
10
CUE INPUT
MONO
STEREO
4
OUTPUTS
5
6
3
ASSIGN
7
2
L
C
R
CLIP
1
8
1
9
0
10
4
5
6
3
7
2
SIGNAL
2
8
1
9
0
4
5
6
3
7
2
SIGNAL
10
3
8
1
9
0
4
5
6
3
7
2
SIGNAL
10
4
8
1
9
0
10
4
5
SIGNAL
5
6
3
7
2
8
1
0
4
5
SIGNAL
10
6
6
3
7
1
9
2
9
8
0
10
4
5
6
3
7
2
SIGNAL
8
1
9
0
POWER
10
CONTROL
CONTROL TYPE
WHAT IT DOES
PROGRAM INPUT
CLIP LED
Illuminates when the program signal
reaches 2 dB below clipping.
Gain Control
Adjusts the level of the program
signal. When you turn control fully
counterclockwise, no program signal
passes. When you turn this control
clockwise, the level of the program
signal increases.
MONO/STEREO Switch
Selects whether the PROGRAM INPUT
signal(s) will be kept separate (stereo
left and right), or summed to mono.
If you are using stereo left and right
inputs, set this switch to STEREO. If
you are using a mono program input,
or if you wish to sum both PROGRAM
INPUTs to mono, set this switch to
MONO. Using MONO, you can also
check the mono compatibility of your
stereo program.
CUE INPUT
ASSIGN LCR Switch
Assigns the cue signal to the left
channel, center channel (both channels simultaneously), or the right
channel of the headphone outputs.
CLIP LED
Illuminates when the cue signal
reaches 2 dB below clipping.
Gain Control
Adjusts the level of the cue signal.
When you turn control fully counterclockwise, no cue signal passes.
When you turn this control clockwise,
the level of the cue signal increases.
9
Symetrix 506E Headphone Amplifier User’s Guide
Front Panel Overview
CONTROL/CONNECTION
CONTROL/CONNECTOR TYPE
WHAT IT DOES
Headphone 1–6 OUTPUTS
Headphone Jack
3-conductor TRS (tip-ring-sleeve)
1/4" jack for connecting stereo
headphones. The minimum impedance is 8 ohms (see Calculating
Maximum Amplifier Load for calculating combined headphone impedances). Be sure to include in your
impedance calculations the headphones connected to the corresponding rear-panel output jack. The tip
contact is the left channel.
SIGNAL LED
Lights to indicate the presence of
signal.
Gain Control
Adjusts the level of signal present at
the headphone output. When you turn
control fully counterclockwise, no
signal will be present. When you turn
this control clockwise, the signal at
the headphone output increases.
CAUTION
The 506E is capable of driving many
headphones past the threshold of
pain. At this volume level, hearing
damage can occur. For your own
hearing health, monitor at a low
sound pressure level.
Power
POWER LED
Lights to indicate the presence of AC
power.
10
Symetrix 506E Headphone Amplifier User’s Guide
Rear Panel Overview
506E
OUTPUT
HEADPHONE
AMPLIFIER
MANUFACTURED BY SYMETRIX INC.
LYNNWOOD, WA USA
THIS PRODUCT CONTAINS NO
USER SEVICEABLE PARTS.
DIRECT
INPUT
6
OUTPUT
DIRECT
INPUT
5
OUTPUT
DIRECT
INPUT
4
OUTPUT
DIRECT
INPUT
3
OUTPUT
DIRECT
INPUT
OUTPUT
2
DIRECT
INPUT
CUE INPUT
PROGRAM INPUTS
MONO
1
RIGHT
LEFT
AC INPUT 25 WATTS MAXIMUM
FABRIQUÉ AUX E.-U. PAR SYMETRIX INC., LYNNWOOD, WASHINGTON.
RÉFÉREZ TOUTE RÉPARATION À UN TECHNICIEN QUALIFIÉ.
CONNECTION
CONNECTOR TYPE
WHAT IT DOES
AC Power Input
IEC Power Connector
Powers the 506E. Connect only to the
AC power source marked on the rear
panel.
OUTPUT
3-conductor TRS (tip-ring-sleeve)
1/4" jack
For connecting to the optional
Symetrix HR-1 Headphone Remote.
The minimum impedance of this
output is 8 ohms (see Calculating the
Maximum Amplifier Load for combining headphone impedances). Be sure
to include headphones connected to
the corresponding front-panel output
jack in your impedance calculations.
The tip contact is the left channel.
DIRECT INPUT
3-conductor TRS (tip-ring-sleeve)
1/4" jack
Allows separate access to the inputs
of each of the 6 headphone amplifiers. When an input is not used, it is
normalled to allow signal from the
506E’s program inputs and cue input
to be fed to this headphone amplifier
section. When a TRS 1/4" connector
is plugged into this jack, it breaks the
signal path, allowing the user to
insert a different line-level signal into
this amplifier section only.
Headphones 1–6
For example, vocalists could use the
first 5 headphone outputs to monitor
the full program, and, by patching a
click track into DIRECT INPUT 6, the
drummer could use headphone output
6 to listen to just the click track.
11
Symetrix 506E Headphone Amplifier User’s Guide
Rear Panel Overview
CONNECTION
CONNECTOR TYPE
WHAT IT DOES
XLR
3-conductor balanced input jack
10 kilohm balanced bridging line input
intended for signals ranging from –10
dBu to +4 dBu. This jack parallels the
1/4" TRS CUE INPUT jack.
1/4" TRS
3-conductor balanced input jack
10 kilohm balanced bridging line input
intended for signals ranging from –10
dBu to +4 dBu. This jack parallels the
XLR CUE INPUT jack.
Right XLR
3-conductor balanced input jack
10 kilohm balanced bridging line input
intended for signals ranging from –10
dBu to +4 dBu. This jack parallels the
1/4" TRS Right PROGRAM INPUT jack.
Right 1/4" TRS
3-conductor balanced input jack
10 kilohm balanced bridging line input
intended for signals ranging from –10
dBu to +4 dBu. This jack parallels the
XLR Right PROGRAM INPUT jack.
Left XLR
3-conductor balanced input jack
10 kilohm balanced bridging line input
intended for signals ranging from –10
dBu to +4 dBu. This jack parallels the
1/4" TRS Left PROGRAM INPUT jack.
Left 1/4" TRS
3-conductor balanced input jack
10 kilohm balanced bridging line input
intended for signals ranging from –10
dBu to +4 dBu. This jack parallels the
XLR Left PROGRAM INPUT jack.
CUE INPUT (MONO)
PROGRAM INPUTS
Note
For the left, right, and cue inputs, XLR
pin 2 corresponds to the tip contact of
the TRS jack and is in phase with the
output signals.
12
Symetrix 506E Headphone Amplifier User’s Guide
Signal Flow Diagram
DIRECT INPUT
LEFT IN
BALANCED
INPUT
FRONT
OUTPUT
SUM
STEREO MONO
REAR
OUTPUT
SUM
RIGHT IN
BALANCED
INPUT
ONE OF 6 CHANNELS
CUE IN
ASSIGN
BALANCED
INPUT
13
Symetrix 506E Headphone Amplifier User’s Guide
Troubleshooting
SYMPTOM
PROBABLE CAUSE / WHAT TO DO
No output
Check cables and connections to see if:
• Inputs are driving outputs, and outputs are driving inputs.
• Unit is plugged in.
• The DIRECT INPUT jack of the headphone channel you are monitoring
has a cable plugged in. If so, unplug this source.
Check controls to see if:
• PROGRAM INPUT and CUE INPUT gain controls are turned up.
• The gain control of the headphone channel that you are monitoring is
turned up.
• If the PROGRAM INPUT’s Mono/Stereo switch is set to MONO, try setting
the switch to STEREO (you may have a phase cancellation problem with
the signal that you are sending to the PROGRAM INPUT).
Verify cables, source, and load.
Replace or verify that headphones are in working order.
Hum or buzz in output
Check input and output connector wiring.
Check for a ground loop problem. Inspect related system equipment grounding to verify that all system components are on the same AC ground.
Distortion
Check if line input signal is too hot or already distorted. If so, turn down the
PROGRAM INPUT and/or CUE INPUT gain controls.
Check the output loading.
Check if something else is clipping.
Check if you are overdriving your headphones. If so, turn down the output
gain control for the channel that you are using.
Noise (hiss)
Check input signal levels. The 506E is intended to operate at or near “line”
level (+4 dBu is nominal). Make sure that the signal you are feeding to the
506E is a line level signal, not mic level.
Check that all systems components are on the same AC ground.
Check gain settings on upstream equipment. The system gain structure
should be such that the 506E receives +4 dBu nominal signal. Check if the
input signal is already noisy.
No LED display
Check if unit is plugged in.
Verify that AC outlet works.
14
Symetrix 506E Headphone Amplifier User’s Guide
Hardware Specifications
Input/Output
Maximum Input Level
Maximum Output Level
Input Impedance
Output Impedance
Indicators
Clip LED
Signal LED
+21 dBu
2000 ohm load: 12V RMS
600 ohm load: +21 dBm
60 ohm load: 3.3V RMS
Program and Cue Inputs: 20K ohms balanced
Direct Channel Inputs: 20K ohms unbalanced
100 ohms
Lights at 2 dB below onset of clipping
Lights at –30 dBu output level
Performance Data
Frequency Response
THD+Noise
Residual Output Noise
Maximum Gain
20 Hz to 20 kHz, +0, –0.5 dB
<0.05%
<-90 dBu
Program and Cue Inputs: 20 dB
Direct Channel Inputs: 10 dB
70 dB @ 1000 Hz typical
Separation
Connections
Input
Output
Power In
Physical
Size (H x W x D)
Weight
Electrical
Power Requirements
Program Inputs and Cue Input: balanced XLR and balanced TRS
Direct Channel Inputs: unbalanced TRS
Unbalanced TRS
Standard IEC Power Inlet
1.72 in. x 19 in. x 7.25 in. / 4.4 cm x 48.3 cm x 18.4 cm
7.6 lbs. / 3.5 kg net
115 VAC nominal, 105 to 125 VAC, 60 Hz, 25W max
230 VAC nominal, 220 to 240 VAC, 50 to 60 Hz, 25W max
15
Symetrix 506E Headphone Amplifier User’s Guide
Architects and Engineers Specifications
The headphone amplifier shall have
stereo left and right program inputs
with a mono/stereo switch and a
mono cue input that is assignable to
left, right, and center. The headphone
amplifier shall have six stereo outputs. Each output shall have its own
volume control, amplifier, and signal
LED. Each output channel shall also
have a direct input, which interrupts
the signal from the program and cue
inputs to that output channel.
The headphone amplifier shall have a
program input gain control with a
mono/stereo switch. A cue input gain
control with LCR toggle switch shall
also be provided. All inputs shall be
balanced bridging inputs. Outputs
shall be suitable for driving headphones in the range of 8 ohms to
2000 ohms. The output source
impedance shall be 100 ohms. The
headphone amplifier shall be
equipped with a program input clip
LED, a cue input clip LED and a
power LED.
The headphone amplifier shall be
capable of delivering 35 volts peakto-peak into a 2000 ohm load.
The headphone amplifier shall be
capable of operating by means of its
own built-in power supply connected
to 115 VAC nominal (105 to 125V),
60 Hz or 230 VAC nominal (220 to
240V), 50 to 60 Hz.
The headphone amplifier shall be a
Symetrix Inc. model 506E Headphone
Amplifier.
16
Symetrix 506E Headphone Amplifier User’s Guide
Warranty
Important Information
Regarding Your Warranty
We would like to offer you an incentive to
complete our product registration form.
Either fully complete and mail your product
registration card or register online at
www.symetrixaudio.com. You will then
have a total of 5 years of warranty
coverage, under the terms and limitations
as set forth below, without additional cost.
If you don’t register your product, you will
still receive one year of warranty coverage,
but it only takes a minute to fill out the
card or register online and we won’t share
your personal information with others.
Following are the terms and limitations of
the Symetrix warranty.
Warranty
Symetrix, Inc. expressly warrants to the
original purchaser (“Buyer”), subject to the
terms and conditions set forth below, that
the Product will be free from defects in
material and workmanship as a result of
normal commercial use for one (1) year
from the date of purchase. This warranty
will be automatically extended (subject to
the additional limitations set forth below)
for an additional four years if the Warranty
Registration is completed and returned to
Symetrix (or completed online) within
thirty (30) days of the date of delivery.
Symetrix’s warranty obligation is limited to
the repair, replacement, or refund at
Symetrix’s sole discretion, of the part or
parts of the Product which may thus prove
defective in materials or workmanship
within one year from date of purchase (or
five years from the date of purchase if
Buyer has registered its purchase as
provided above) under normal use and
which our examination discloses to our
satisfaction to be thus defective, provided
that Buyer gives Symetrix prompt notice of
its warranty claim and satisfactory proof
thereof.
Symetrix will make every reasonable effort
to ensure that parts are available to
support the repair of our products under
warranty. In the event that a product or
component part thereof becomes obsolete,
unavailable or irreparable, Symetrix
reserves the right to refund a prorated
portion of the purchase price in full
satisfaction of all warranty claims. A refund
of the purchase price is prorated as
follows: 100% through year one, 80%
through year two, 60% through year three,
40% through year four and 20% through
year five.
In order to serve you better we request
that the Buyer shall, prior to shipping
Product to Symetrix for warranty service,
contact Symetrix and secure a Return
Authorization Number that shall be
included with the returned Product. This
will facilitate our efforts to keep track of
your Product and process your warranty
repair as quickly as possible. Buyer will
prepay all freight charges to ship the
Product to Symetrix for warranty inspection
and service. This warranty is subject to
Symetrix’s inspection of the Product at its
facilities and, upon Symetrix’s request,
satisfactory proof of purchase (dated copy
of original retail dealer’s invoice.)
Symetrix reserves the right to effect
repairs to the product with reconditioned
components/parts. Products once repaired
under warranty will be shipped to Buyer
freight prepaid by Symetrix via United
Parcel Service (surface) or any similar
shipper, to any location designated by
buyer within the Continental United States.
At Buyer’s request and expense Product
will be returned via airfreight. Outside the
continental United States, repaired or
replaced products will be returned freight
collect.
THIS WARRANTY IS EXPRESSLY IN LIEU OF
ALL OTHER WARRANTIES EXPRESS OR
IMPLIED, ARISING BY LAW OR OTHERWISE
(INCLUDING, WITHOUT LIMITATION ANY
OBLIGATIONS OF THE SELLER WITH
RESPECT TO CONSEQUENTIAL DAMAGES)
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE
AND OF ALL OTHER OBLIGATIONS OR
LIABILITIES ON OUR PART, AND WE
NEITHER ASSUME, NOR AUTHORIZE ANY
OTHER PERSON TO ASSUME FOR US, ANY
OTHER LIABILITY IN CONNECTION WITH
THE SALE OF THE PRODUCT. THIS
WARRANTY SHALL NOT APPLY TO THIS
PRODUCT OR ANY PART THERE OF WHICH
HAS BEEN SUBJECT TO ACCIDENT,
NEGLIGENCE, ALTERATION, ABUSE, OR
MISUSE. WE MAKE NO WARRANTY
WHATSOEVER IN RESPECT TO ACCESSO-
RIES OR PARTS NOT SUPPLIED BY US. THE
TERM “ORIGINAL PURCHASER,” AS USED
IN THIS WARRANTY SHALL BE DEEMED TO
MEAN THAT PERSON OR COMPANY THAT
ORIGINALLY PURCHASED THE PRODUCT.
This Symetrix product has been designed
and manufactured for use in professional
and studio audio systems and is not
intended for other usage. This warranty
only applies to Buyers using the Product in
professional and studio audio systems.
With respect to others, including but not
limited to consumers for personal, family,
or household use, Symetrix expressly
disclaims all warranties, including but
not limited to warranties of merchantability and fitness for a particular
purpose and the express warranties as
otherwise provided herein.
Symetrix reserves the right to modify the
design or make additions to, or improvements to, its product lines without making
similar upgrades to Product purchased by
Buyer. Symetrix does not authorize any
third party, including any dealer or sales
representative, to assume any liability,
effect any repairs or modifications to the
Product, or make any additional warranties
or representation regarding the Product or
Product information on behalf of Symetrix.
Symetrix’s total liability on any claim,
whether in contract, tort (including
negligence) or otherwise arising out of,
connected with, or resulting from the
manufacture, sale, delivery, resale, repair,
replacement or use of Product will not
exceed the purchase price of the Product or
any part thereof which gives rise to the
claim. In no event will Symetrix be liable
for any incidental or consequential
damages including but not limited to
damage for lost revenue, cost of capital,
claims of customers for service interruptions or failure to supply, and costs and
expenses incurred in connection with labor,
overhead, transportation, installation or
removal of products or substitute facilities
or supply houses as a result of Product
failure.
This limited warranty gives Buyer certain
rights. Buyer may have additional rights
under applicable law.
17
Symetrix 506E Headphone Amplifier User’s Guide
Service
Where to Get Service
To Get Your 506E Unit Repaired (US Customers Only)
If outside of the USA
1
If you have determined that your
506E requires repair services and you
live outside of the United States,
please contact your local Symetrix
dealer or distributor for instructions
on how to obtain service.
If inside the USA
Symetrix will perform in-warranty or
out-of-warranty service on any
product it has manufactured for a
period of five years from date of
manufacture. If you reside in the
USA, then proceed as follows:
In-Warranty Repairs
Repairs made in-warranty will cost
you only one-way freight charges.
We’ll prepay the return (surface)
freight. Of course, if the repair is due
to operator error, parts and labor will
be charged. If there are charges for
the repair costs, you will pay for the
return freight. All charges will be COD
unless you have made other arrangements (prepaid, Visa, or Mastercard).
Call our Technical Services Group for a return authorization (RA) number.
(888) 349-3222, Monday through Friday, 6:00 am to 4:30 pm Pacific Time
Have your serial number ready to give to the service representative.
You will find it on the bottom of the 506E unit.
2
Pack the unit in its original packaging materials.
3
Include your name, address, daytime telephone number, and a brief
statement of the problem.
4
Write the RA number on the outside of the box.
5
Ship the unit to Symetrix, freight prepaid. We do not accept freight
collect shipments.
Symetrix, Inc.
14926 35th Ave West
Lynnwood WA 98037
If You Don't Have Factory Packaging Materials
If you send us your product in substandard packaging, we will charge you for
factory shipping materials. If you don’t have the factory packaging materials, do
the following:
1
Select an oversized carton.
2
Wrap the unit in a plastic bag, and surround it with bubble-wrap.
3
Pack the box full of Styrofoam peanuts. Be sure there is enough clearance in the carton to protect the rack ears.
We will return the unit in Symetrix packaging.
Out-of-Warranty Repairs
If the warranty period has passed,
you’ll be billed for all necessary parts,
labor, packaging materials, and
freight charges.
18
Symetrix 506E Headphone Amplifier User’s Guide
Declaration of Conformity
We, Symetrix, Inc.
14926 35th Avenue West, Lynnwood, Washington USA
declare under our sole responsibility that the product:
506E Headphone Amplifier
to which this declaration relates, is in conformity with the following standards:
EN 60065
Safety Requirements for Mains Operated Electronic and Related Apparatus for
Household and Similar General Use
EN 55103-2
Electromagnetic Compatibility—Product Family Standard for Audio, Video, and
Entertainment Lighting Control Apparatus for Professional Use
Part 2: Immunity
The technical construction file is maintained at:
Symetrix, Inc.
14926 35th Avenue West
Lynnwood, WA 98037-2303
USA
The authorized representative located within the European Community is:
World Marketing Associates
P.O. Box 100
St. Austell, Cornwall, PL26 6YU, UK
Date of issue: July 25, 2000
Place of issue: Lynnwood, Washington USA
Authorized signature:
Dane Butcher, President
19
301
Low Distortion Compressor/Limiter
302
Dual Microphone Preamplifier
303
Interface Amplifier
304
Headphone Amplifier
305
Distribution Amplifier (1x4)
306
Preamp/Ducker
307
Dual Isolation Transformer
308
VCA Volume Control/Loudness EQ
372
SPL Computer
402
Dual Output Delay
420
Stereo Power Amplifier
421M
AGC-Leveler
422
Stereo AGC-Leveler
440
Foreground Audio Controller
450
Dual Zone Priority Mixer
501
Peak-RMS Compressor/Limiter
501-01
Peak-RMS Compressor/Limiter
506E
Headphone Amplifier
527E
Voice Processor
528E
Voice Processor
531E
Graphic Equalizer
532E
Graphic Equalizer
533E
Graphic Equalizer
551E
5-Band Parametric EQ
552E
Dual 5-Band Parametric EQ
562E
Windowing Expander/Gate
565E
Dual Compressor/Limiter/Expander
571
SPL Computer
571S
SPL Computer Slave
572
SPL Computer
581E
Distribution Amplifier (4x4)
606
Delay F/x Machine
610
Broadcast Audio Delay
628
Digital Voice Processor
9022
2x2 DSP Engine
HR-1
Headphone Remote for 304 and 506E
RC-1
628 Remote Control
RC-2
440 Remote Control
RC-610
Remote Control
www.symetrixaudio.com