Download User`s Manual Model LL1200 PC-based Custom

Transcript
5.5.1
Data Area for Loop-1 PID Parameters
Register No.
301 to 321
5-20
Data Category
Group-1
parameters for loop 1
Description
1.SV.1: Target setpoint
1.A1.1: Alarm 1 setpoint
1.A2.1: Alarm 2 setpoint
1.A3.1: Alarm 3 setpoint
1.A4.1: Alarm 4 setpoint
1.P.1: Proportional band
1.I.1: Integral time
1.D.1: Derivative time
1.MH.1: Upper limit of output
1.ML.1: Lower limit of output
1.MR.1: Manual reset
1.H.1: Hysteresis
1.DR.1: Direct/reverse action switchover
1.Pc.1: Cooling-side proportional band
1.Ic.1: Cooling-side integral time
1.Dc.1: Cooling-side derivative time
1.Hc.1: Cooling-side relay hysteresis
1.DB.1: Deadband
1.RP.1: Zone PID reference point
1.PM.1: Preset output value
1.PMc.1: Cooling-side preset output value
326 to 346
Group-2
parameters for loop 1
351 to 371
Group-3
parameters for loop 1
376 to 396
Group-4
parameters for loop 1
The group-4 parameters for loop 1, i.e., 4.SV.1, . . ., 4.PMc.1,
are functionally the same as their corresponding group-1
parameters for loop 1 listed above, i.e., 1.SV.1, . . ., 1.PMc.1.
401 to 421
Group-5
parameters for loop 1
The group-5 parameters for loop 1, i.e., 5.SV.1, . . ., 5.PMc.1,
are functionally the same as their corresponding group-1
parameters for loop 1 listed above, i.e., 1.SV.1, . . ., 1.PMc.1.
426 to 446
Group-6
parameters for loop 1
The group-6 parameters for loop 1, i.e., 6.SV.1, . . ., 6.PMc.1,
are functionally the same as their corresponding group-1
parameters for loop 1 listed above, i.e., 1.SV.1, . . ., 1.PMc.1.
451 to 471
Group-7
parameters for loop 1
The group-7 parameters for loop 1, i.e., 7.SV.1, . . ., 7.PMc.1,
are functionally the same as their corresponding group-1
parameters for loop 1 listed above, i.e., 1.SV.1, . . ., 1.PMc.1,
where RHY.1 corresponding to 1.RP.1 denotes the zone PID hysteresis.
476 to 496
Group-8
parameters for loop 1
The group-8 parameters for loop 1, i.e., 8.SV.1, . . ., 8.PMc.1,
are functionally the same as their corresponding group-1
parameters for loop 1 listed above, i.e., 1.SV.1, . . ., 1.PMc.1,
where RDV.1 corresponding to 1.RP.1 denotes the zone PID
reference deviation.
Remarks
Selecting an SV number
by means of the SV
number selection parameter
"SVNO," results in the
parameters for
communication, custom
computation or as external
contact inputs being
assembled in groups and
used in the group to which
that SV number belongs.
Thus, switches in the
parameter group occur
simultaneously in both
loop 1 and loop 2.
For example, if you set
the SVNO parameter to 5,
the parameters
5.SV.1, . . ., 5.PMc.1 are
used.
The group-2 parameters for loop 1, i.e., 2.SV.1, . . ., 2.PMc.1,
For details on the
are functionally the same as their corresponding group-1
parameters, see the
parameters for loop 1 listed above, i.e., 1.SV.1, . . ., 1.PMc.1.
US1000 Digital Indicating
The group-3 parameters for loop 1, i.e., 3.SV.1, . . ., 3.PMc.1, Controller–Functions
instruction manual
are functionally the same as their corresponding group-1
parameters for loop 1 listed above, i.e., 1.SV.1, . . ., 1.PMc.1. (IM 5D1A01-02E).
IM 5G1A11-02E