Download EM3DS Manual

Transcript
As to the speed, EM3DS always performed very well thanks to its Asymptotic Estimator, which
performs a full simulation only at the first frequency point. Moreover, since version 7 is available a
new powerful device, SmartFIT: this algorithm adaptively drives the EM solver, generating a
frequency list within the user-selected band. At the end it estimate the response all over that band, in
tents or hundreds of points. Of course it is possible to exploit a rational interpolator even in postprocessing, but without the same guarantee to get good results.
An important companion to this algorithm, is a wide-band Spice Model extractor: it generates a
network, which reproduces the response all over the band, regardless of the electrical length of the EM
circuit.
In the release 9 several completely new features were added, such as internal planar ports, antenna
functions (namely sense layer to see the E-field and to evaluate radiated far field, both in standard
polar diagrams, or in 3D surfaces), object oriented pascal scripting, tuner, enhanced editing etc. In
version 10 you will find a first version of a Macromodel creator: for a given parameter, EM3DS
extracts some features, in order to be able to predict the circuit response in real-time when such a
parameter is modified. This is an extremely useful tool for the design. At the moment it is limited to a
single parameter but more work is in progress. Additionally the multi-mode calibration algorithm has
been enhanced to allow its application in several measurement problems. EM3DS 10 was developed
to reduce the time needed to learn how use it, with many on-line animated tutorial.
Version 11 (end 2010) introduces the Time Domain Reflectometry: a set of time-domain
functions, including the possibility to analyze the time domain to an arbitrary response, and to see the
time domain evolution of current/field distributions. Version 11 also adds the possibility to define
your own measurements (custom measurement definition).
Version 12 (fall 2011) enhances the parametric capabilities of EM3DS, allowing to parametrize
also the thickness of each substrate, to define a list of sets of parameters, and to automatically perform
simulations and comparisons for each set of parameters. Moreover several minor improvements are
made available (additional animated tutorials, printing and print preview utilities etc)
Since ver 6.0 EM3DS was the first tool allowing the full-wave modeling of FETs in linear
regime: this is accomplished through the insertion of distributed controlled current sources. EM3DS
6.0 provides for the materials’ constitutive parameters to be frequency dependent, and may further be
specified by the user through analytical expressions (formulas). Every parameter in EM3DS can
conveniently be input as a valid algebraic expression, (for instance: sin(3.5)), and is fully evaluated
(calculated) by EM3DS, thus facilitating the overall process and avoiding using calculators.
Unlike some other commercially available tools, EM3DS does not pose any requirement on the grid.
The only event when grid is desirable, and in fact EM3DS can make use of it, is during the
drawing, where it offers additional flexibility.
As stated above, EM3DS comes integrated with several tools, aimed to ease interfacing with other
CAE tools. As to the pre-processing step, filters allowing importing GDSII and DXF (as well as
general bitmaps) are available. The post-processor includes a Spice Model Extractor, a simple Linear
Circuit Simulator, tools for saving animations (GIF, AVI), link to AVI files via multimedia
documents, exporting graphs (plots, Smith Charts), data files (Touchstone), to see the interaction
between a user-defined magneto-static field and RF currents flowing across an object etc.
Nonetheless for MEM Research it is imperative to look for partnerships in order to better
exploiting the EM3DS power. This is why in the past EM3DS 5 was also fully integrated as
®
Electromagnetic Module in the multi-physic package by Corning Intellisense, Intellisuite .
TM
Currently, EM3DS is companion of CoventorWare , by Coventor, leading company in the MEMS
software development: EM3DS was carefully selected by Coventor thanks to its remarkable
achievements.
By the same token EM3DS has now the ability to be accessed directly from the AWR Microwave
Office (since version 6 of MWO) suite. This means that AWR’s customers are able to see EM3DS as
an electromagnetic engine, still using Microwave Office editor and post-processing capabilities.
Refers to the section for details on how to use this feature.
II What’s new in Ver. 12 (2011)
•
Extended parametric features: substrates can have parametric thickness
2