Download Operation instructions DH77 Touchscreen
Transcript
Version HW0.12 Operation available and activated). As an example, we provide here logging on the printer: Di 19.03.02 08:36:43 calibration started Di 19.03.02 Work 08:37:53 Di 19.03.02 Filter change 08:38:15 Di 19.03.02 Blower on 08:38:31 Di 19.03.02 08:40:43 calibration for 500 l/min at av. station conditions flow meters interior TECFLUID 420-600 refer. KDE/MOBREY p(act) outdoor [hPa]: 950 T(act) outdoor [K]: 295 pM (500 l/min) [hPa]: 911 TM (500 l/min) [K]: 297 p(average) [hPa]: 1011 T(average) [K]: 286 p(stand) [hPa]: 1013 T(stand) [K]: 273 pos. cal. point [mm]:129,0 offset cal. Mark [mm]: -0,4 cal. pos(station)[mm]:129,9 pos. swimmer [mm]:130,0 pos. int.(input) [mm]:131,0 pos. int.(target)[mm]:137,4 offset int. Scale[mm]: -6,4 offset filter [mm]: -7,1 Q scale outd. [l/min]:500,8 Q amb. act. [l/min]:523,4 Q scale indoor[l/min]:513,6 Q stand [l/min]:476,3 change [%]: 0,1 Di 19.03.02 Blower off 08:43:17 Di 19.03.02 08:43:17 end of calibration 7.5 for average station conditions on the installation site in calibrated flowmeter Pos. swimmer [mm]: Floater position on calibrated flowmeter before calibration pos. int.(Input) [mm]: Floater calibrated position in the integrated flowmeter pos. int.(target) [mm]: Floater set-point position after calibration in the integrated flowmeter Offset int. scale[mm]: Difference between integrated flowmeter scale and calibration table (at Q amb. act.) Offset filter [mm]:– Offset Difference between calibrated filter [mm] flowmeter and integrated flowmeter on the basis of the filter resistance (depends on lower pressure in integrated flowmeter). Pos. int. (target) [mm] = cal. pos.(Station) [mm] – Offset cal. point [mm] Q scale outd. [l/min]: Flow rate on the calibrated flowmeter after calibration related to station conditions Q amb. act. [l/min]: Current Flow rate on the calibrated flow rate on the calibrated flowmeter after calibration related flowmeter after calibration at to station conditions current conditions Q scale indoor [l/min ]: Set flow rate on the integrated flowmeter after calibration (this value should also automatically be taken over as an operation flow rate into control) Q standard [l/min]: Flow rate after calibration related to standard conditions change [%]: ((Actual value – Target value) / Target value) * 100 Actual value ... Pos. Floater The flow rate variation of the Target value ... Pos. (Station) previous calibration (positive values indicate an decrease, negative values indicate a increase in the flow rate due to re-calibration) 7.6 Meaning of abbreviations p(act)outdoor [mbar]: T(act) outdoor [K]: pM (500 l/min) [mbar]: TM (500 l/min) [K]: p(average) [mbar]: T(average) [K]: p(standard) [mbar]: T(standard) [K]: pos. Cal. Point [mm]: Offset cal. Mark [mm]: cal. pos(Station) [mm]: Current pressure on the calibrated flowmeter Current temperature on the calibrated flowmeter Current pressure on the integrated flowmeter Current temperature on the integrated flowmeter Average yearly pressure at the installation site (station condition) Average yearly temperature at the installation site (station condition) Standard air pressure Standard air temperature calibration point position on calibrated flowmeter Difference between calibration position and calibration table 500 l/min position Position of the floater calibrated Determination of standard & operation volumes Considering the pressure and temperature values determined during the sampling period on the integrated flowmeter, the values for VStandard (= Vs) or Vmeas.system (= VM) or in following for Vamb. (= VA) are calculated from the equation (7) (Chapter 6.3.2) as listed below: The equation (3) yields: (8) Qm = QScale indoor × (pref × Tm) (Tref × pm) Qm : QScale indoor: p m: Tm: average flow rate on the flowmeter during a sampling period a set flow rate (e.g. automatically determined by calibration) average pressure on the integrated flowmeter during a sampling period average temperature on the integrated flowmeter during a sampling period Vm = Qm × t S 19 DIGITEL Elektronik AG Alte Gasse 18 CH-8604 Hegnau Tel.: +41 (44) 908 20 30 DIGITEL Elektronik GmbH Illstrasse 30 A-6706 Bürs Tel.: +43 (5552) 67850 www.digitel-ag.com [email protected]