Download lbi-38985b - The Repeater Builder`s Technical Information Page

LBI-38985B
LOCAL INTERCONNECT
for the next call? Default is 4 seconds. (The value
of this parameter cannot be reconfigured in the Site
Controller’s Active Configuration through the
System Manager, and therefore must be
programmed in the Site Controller’s Personality
PROMs.) (See the Interconnect Timing Settings
heading for more information.)
•
•
Ring Radio on Landline Originated (Interconnect
Data for RIC/LIC Interconnect only) - Do you want
the local telephone interconnect equipment to ring
the called radio? Default is yes. (The value of this
parameter cannot be reconfigured in the Site
Controller’s Active Configuration through the
System Manager, and therefore must be
programmed in the Site Controller’s Personality
PROMs.)
Allow Landline to GID Calls (Interconnect Data) Are GIDs enabled to receive telephone-originated
interconnect calls (same for each GID)? Default is
yes for each GID. (The value of this parameter can
be reconfigured in the Site Controller’s Active
Configuration through the System Manager - see
the Inb Interconnect (Radio Parameter) parameter.)
Values for the following Telephone Interconnect
parameters are configurable in the System Manager’s
database for the site. The database for the site is then used to
reconfigure the values of these parameters in the Site
Controller’s Active Configuration whenever the Site
Controller is powered up or reset, or a system administrator
makes changes through the System Manager. (Note that
whenever the Site Controller is powered up or reset, the Site
Controller will use the values in its Personality PROMs until
its Active Configuration is reconfigured by the site database
from the System Manager.)
•
•
56
Interconnect (Channel Configuration) - Which
channels are enabled for telephone interconnect
calls? Choices are Y (enabled) or N (disabled), for
each channel from 1 to 24. The Site Controller
default is Y (enabled) for each channel from 1 to
20. The System Manager default is N (disabled) for
each channel from 1 to 24. (Only channels
equipped with a RIC Shelf or GTI Unit should be
enabled.)
Interconnect Hang Time (Site Parameters) - How
much time should be allowed between unkey
(release of the PTT key on the radio) and channel
drop for telephone interconnect calls? Range is
from 1 to 255 seconds. The Site Controller and
System Manager defaults are 30 seconds.
•
Max # Concurrent Intcon (Site Parameters) - What
is the maximum number of concurrent telephone
interconnect calls permitted for this site? Range is
from 0 to 30. The Site Controller default is 20.
The System Manager default is 2.
•
Interconnect (Radio Parameters) - What queue
priority will be used for telephone interconnect
calls to/from this LID (different value for each
LID)? Range is from 0 (lowest priority) to 7
(highest priority). The System Manager default is
0.
•
Interconnect (Group Parameters) - What queue
priority will be used for telephone interconnect
calls to this GID (different value for each GID)?
Range is from 0 (lowest priority) to 7 (highest
priority). The System Manager default is 0.
•
Inb Interconnect (Radio Parameters) - Is this LID
enabled to receive telephone-originated interconnect calls (different for each LID)? Choices are
Y (enabled) and N (disabled). The Site Controller
and System Manager defaults are N (disabled) for
each LID.
•
Inb Interconnect (Group Parameters) - Is this GID
enabled to receive telephone-originated interconnect calls (different for each GID)? Choices are
Y (enabled) and N (disabled). The Site Controller
default is Y (enabled) for each GID. The System
Manager default is N (disabled) for each GID.
•
Toll Call Rest (Radio Parameters) - Which toll call
restriction level applies to this LID for radiooriginated interconnect calls? Range is 0 (no
access to any telephone number) or from 1 to 15.
The Site Controller and System Manager defaults
are 0 for all LIDs.
•
Toll Call Parameters (table) - Which digit patterns
(for the first four digits of a called telephone
number) are allowed (Y) and which digit patterns
(for the first four digits of a called telephone
number) are denied (N) for each toll call restriction
level? Digit choices are a space (wildcard for *, #,
or any number from 0 to 9), an X (wildcard for any
number from 0 to 9), or a number from 0 to 9.
(Unused digit patterns are represented by four
periods.) The Site Controller default allows all
patterns (with four spaces) for each restriction
level. The System Manager default allows no
patterns (with four periods) for each restriction
level.