Download Installation Instructions for RS6506

PARTS LIST
P/N
130019
170081
170082
176080
176081
176082
176083
176084
176085
176086
176088
176089
420027
602612
615
616
7727
860070
860072
420026
860086
170078
860155
420088
545
DESCRIPTION
Rear Track Bar Bracket
Right Brake Line
Left Brake Line
Front Link
Rear Link
Top Swivel, Front End Link
Center Section, Front End Link
Bottom Socket, Front End link
Bracket, Front End Link
Track Bar
Rear End Link
Front Bump Stop Perch
Rear Bump Stop Spacer
Track bar End (Ball joint)
Front Coil Spring
Rear Coil Spring
Pitman Arm
Shim Kit
Washer
Rear Track Bar Relocation Kit
Sleeve
7/16-14x1.0 HHCS
7/16-14 Stover Nut
7/16 SAE Washer
M12-1.75x70 HHCS
M12-1.75 Nut
SAE Washer
3/8-16x1.0 HHCS
3/8-16 Stover Nut
3/8 SAE Washer
Gasket Kit
Brake Line Gasket
Rear End Link Hardware Kit
Sleeve, Rear End Link
Bushing
7/16-20x2.5 HHCS
7/16-20 Stover Nut
7/16 SAE Washer
7/16 USS Washer
QTY.
1
1
1
2
2
2
2
2
2
1
2
2
2
1
2
2
1
1
16
1
1
1
1
2
2
2
4
1
1
2
1
4
1
4
4
4
4
2
6
P/N
860156
176087
860157
420086
520086
860158
770057
770071
860159
420084
545
860160
176090
860161
176091
176092
860218
420080
520080
88056
94140
DESCRIPTION
Spring Retainer Kit
Spring Clip
3/8-16x1.0 HHTS
3/8-16x1.5 HHTS
Front Track Bar Hardware Kit
Sleeve
Bushing
3/4-16 Jam Nut
Quick Pin Kit
Quick Pin Assembly
Rubber Washer
Quick Disconnect Hardware Kit
Sleeve, Front End Link
Bushing
1/2-20x2.75 HHCS
1/2-20x1.75 HHCS
1/2-20 Nyloc Nut
1/2 SAE Washer
1/2 USS Washer
M10-1.50 Nut
Shift Relocation Kit
Bracket
1/4-20x.75 BHCS
1/4 SAE Washer
1/4-20 Nyloc Nut
Thread Lock
Skid Plate Spacer Kit
Skid Plate Spacer
Skid Plate Shim
1/2 Cone Washer
1/2-13x2.5 FSHCS
M10-1.50x70 HHCS
10mm Lock Washer
Articulation Bushing Kit
Sleeve
Bushing
Instructions
Consumer Information Pack
QTY.
1
2
2
2
1
1
2
1
1
2
4
1
2
2
2
2
4
2
6
2
1
1
4
4
4
2
1
6
6
6
6
2
2
1
8
16
1
1
RANCHO LINK ASSEMBLY
BUSHING & SLEEVE INSTALLATION
1) Lubricate the outside diameter of two urethane
bushings (part No. 520080) with a silicone spray or a mild
solution of soap and water.
2) Press the lubricated bushings into one end of a new
Rancho lower link (176080 or 176081) as shown in figure 1.
3) Lubricate the outside diameter of sleeve 420080
and the inside diameter of the installed urethane bushings.
Press the sleeve into the bushings.
Figure 1
NOTE: It may be necessary to use a bench vise or C-clamp
to press the bushings and sleeves into the lower links. Do
not use a hammer.
4) Slowly apply grease to each end of the lower links
(through the grease fitting) with a grease gun. Stop when
3