Download 2014 Instructions - College Hills Honda
Transcript
www.collegehillshonda.com INSTALLATION INSTRUCTIONS PARTS LIST Accessory Application XM RADIO SYSTEM 2014 CIVIC 2 AND 4-DOOR Publications No. AII 50687 Issue Date NOV 2013 Clip XM Radio Attachment Kit P/N 08B15-TR0-100 Bus cable Wire tie with clip 2 Brackets Accessory User’s Information Manual 2 Spacers (Some may not used) 6 Washer bolts XM Antenna Kit (sold separately) P/N 08A15-0J1-100 Antenna 7 Wire ties Unit Kit (sold separately) P/N 08A15-TR0-100 XM radio unit 8 Urethane tapes Cover seal 2-Port bus cable Kit (sold separately) P/N 08A31-0F1-000 2-Port bus cable © 2013 American Honda Motor Co., Inc. – All Rights Reserved. AII 50687 (1311) 08B15-TR0-1001-90 1 of 12 www.collegehillshonda.com TOOLS AND SUPPLIES REQUIRED Illustration of the XM Radio System in the Vehicle Phillips screwdriver Flat-tip screwdriver ANTENNA Shop towel Scissors Ratchet BUS CABLE 8 mm and 10 mm Sockets Isopropyl alcohol Tape measure Diagonal cutters Tape The following tool is available through the Honda Tool and Equipment Program. On the iN, click on: Service > Service Bay > Tool and Equipment Program, then enter the number under “Search”. Or, call 888-424-6857. XM RADIO UNIT • Plastic Trim Tool (T/N SILTRIMTL10) 2-PORT BUS CABLE Q081801AK BUS CABLE XM RADIO UNIT ANTENNA AUDIO UNIT 2-PORT BUS CABLE Q082009AK 2 of 12 AII 50687 (1311) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. www.collegehillshonda.com INSTALLATION 3. Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” 1. Disconnect the negative cable from the battery. 2. Remove the passenger’s sunvisor holder. Wrap the end of a flat-tip screwdriver with tape. Locate the slot in the bracket cover, and insert a flattip screwdriver into the slot. Push the hook with the flat-tip screwdriver. FLAT-TIP SCREWDRIVER BRACKET COVER PASSENGER’S SUNVISOR TAPE HOOK FRONT PASSENGER’S SUNVISOR Make sure the hook slides into the bracket cover. PASSENGER’S SUNVISOR HOLDER (Rotate.) Q082007AK Push the hook. While pushing in on the hook, rotate the sunvisor backward about 45°. Q091503BK 4. © 2013 American Honda Motor Co., Inc. – All Rights Reserved. AII 50687 (1311) While pushing in on the hook, rotate the passenger’s sunvisor backward about 45°. Make sure the hook slides into the bracket cover. NOTE: If the hook did not stay pushed in, return the passenger’s sunvisor to its original position and repeat steps 3 and 4. 3 of 12 www.collegehillshonda.com 5. For 4-Door Models Remove the passenger’s sunvisor. 8. Pull away the passenger’s door opening seal. PASSENGER’S A-PILLAR Pull the clip. FRONT PASSENGER’S A-PILLAR CLIP PASSENGER’S A-PILLAR TRIM PASSENGER’S SUNVISOR Q091504AK For 2-Door Models 6. DOOR OPENING SEAL (Pull away.) CLIP Pull away the passenger’s door opening seal. PASSENGER’S A-PILLAR 9. Pull the clip. QA20101AK Pull out the passenger’s A-pillar trim to release the clips. 10. Put a shop towel in the opening between the passenger’s A-pillar trim and the dashboard to prevent dropping the A-pillar clips. Take care not to damage the passenger’s A-pillar trim. PASSENGER’S A-PILLAR CLIP PASSENGER’S A-PILLAR TRIM PASSENGER’S A-PILLAR TRIM 2 CLIPS 7. DOOR OPENING SEAL (Pull away.) PASSENGER’S A-PILLAR Q082004AK Pull out the passenger’s A-pillar trim to release the clips. DASHBOARD SHOP TOWEL 4 of 12 AII 50687 (1311) Q091502AK © 2013 American Honda Motor Co., Inc. – All Rights Reserved. www.collegehillshonda.com 11. Remove the passenger’s A-pillar trim from the upper clip (unplug the vehicle connector, if equipped). Carefully remove the shop towel and any clips that fell from the passenger’s A-pillar trim. NOTE: The upper clip will stay in the body. VEHICLE CONNECTOR (if equipped) 13. Install the new clip (supplied) to the passenger’s A-pillar trim. NOTE: When reinstalling the A-pillar trim, refer to the service manual for the correct overlap procedure. UPPER CLIP CLIP (supplied) PASSENGER’S A-PILLAR TRIM PASSENGER’S A-PILLAR TRIM Q082309AK Q0N0533AH 14. Remove the passenger’s front door sill trim (six clips, two hooks, and four retaining tabs). 12. Remove the remaining upper clip from the passenger’s A-pillar. 2 HOOKS FRONT Push two tabs. 6 CLIPS PASSENGER’S A-PILLAR UPPER CLIP (Discard.) PASSENGER’S FRONT DOOR SILL TRIM 4 RETAINING TABS Q082003AK Q082006AK © 2013 American Honda Motor Co., Inc. – All Rights Reserved. AII 50687 (1311) 5 of 12 www.collegehillshonda.com 15. Pull away the door opening seal, and remove the passenger’s kick panel (two clips). • Open the glove box, push inward on the stops, and remove the glove box. STOPS (Push inward.) DOOR OPENING SEAL (Pull away.) CLIP GLOVE BOX CLIP PASSENGER’S KICK PANEL Q081901AK 17. To protect the vehicle, attach tape to the dashboard in the areas shown. Move the shift lever to the N (neutral) position, and wrap a shop towel around the shift lever. 16. Remove the glove box: • Q072102AH Remove two bolts. GLOVE BOX SHIFT LEVER (N POSITION) TAPE 2 BOLTS Q072101BH 6 of 12 AII 50687 (1311) CENTER LOWER PANEL SHOP TOWEL QB51501BK © 2013 American Honda Motor Co., Inc. – All Rights Reserved. www.collegehillshonda.com 18. Remove the center lower panel (two self-tapping screws, four clips, and unplug the vehicle connectors, if equipped). VEHICLE CONNECTORS (if equipped) 20. To protect the vehicle, attach tape to the dashboard, center panel, and wiper/washer switch in the areas shown. WIPER/WASHER SWITCH TAPE 4 CLIPS DASHBOARD TAPE TAPE CENTER PANEL 2 SELF-TAPPING SCREWS CENTER LOWER PANEL QB41901AK 19. Remove two bolts and two self-tapping screws. QB51701BK 21. Remove the center panel (six clips, aspirator hose, and unplug the vehicle connectors). 6 CLIPS ASPIRATOR HOSE VEHICLE CONNECTORS 2 SELF-TAPPING SCREWS 2 BOLTS QB51704AK CENTER PANEL © 2013 American Honda Motor Co., Inc. – All Rights Reserved. AII 50687 (1311) QB41301BK 7 of 12 www.collegehillshonda.com Installing the XM Radio Unit 22. Loosely install two brackets to the audio unit with two washer bolts. NOTE: There is the gap between the brackets and XM radio unit. Use the spacer to adjust the gap. 25. Using isopropyl alcohol on a shop towel, clean the area on the edge of the XM radio unit as shown. Clean with isopropyl alcohol. 2 CUT URETHANE TAPES AUDIO UNIT 2 WASHER BOLTS (Loosely install.) XM RADIO UNIT 2 BRACKETS URETHANE TAPE (Cut.) Q081807BK 26. Cut the urethane tape as shown. 27. Attach two halves of urethane tape to the XM radio unit as shown. BRACKET 28. Wrap two urethane tapes around two 2-port bus cable connectors as shown. QB51702AK SPACER (There is the gap between the brackets and XM radio unit.) 23. Install the XM radio unit to the brackets in the audio unit with four washer bolts. 2 URETHANE TAPES 2-PORT BUS CABLE AUDIO UNIT Align. Align. Q081808AK 2 BRACKETS 2 WASHER BOLTS 4 WASHER BOLTS XM RADIO UNIT QB51703BK 24. Secure two washer bolts installed in step 22. 8 of 12 AII 50687 (1311) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. www.collegehillshonda.com 29. Plug the bus cable connector into the XM radio unit. Routing the Antenna Cable 31. Cut three urethane tapes in half as shown. 850 mm (33.5 in.) 50 mm (2.0 in.) XM RADIO UNIT 150 mm (5.9 in.) BUS CABLE ANTENNA Q081702AK 30. Plug the 2-port bus cable into the audio unit connector and the bus cable connector. ANTENNA CABLE 3 URETHANE TAPES (Cut.) Q0N1501AK 32. Wrap six halves of urethane tape around the antenna cable at the measurements shown. 33. Using isopropyl alcohol on a shop towel, clean the area shown on the inside of the windshield. AUDIO UNIT 2-PORT BUS CABLE INSIDE Align. BUS CABLE ANTENNA Q081703AK 50 mm (2.0 in.) Clean with isopropyl alcohol. ANTENNA WINDSHIELD 4 ADHESIVE BACKINGS Q081705BK 34. Remove four adhesive backings from the antenna, and attach the antenna in the location shown. Apply firm pressure to securely attach the antenna. © 2013 American Honda Motor Co., Inc. – All Rights Reserved. AII 50687 (1311) 9 of 12 www.collegehillshonda.com 35. Using isopropyl alcohol on a shop towel, clean the area shown on the outside of the windshield. 39. Route the antenna cable down. Loosely secure the antenna cable to the vehicle harness with one wire tie. GLOVE BOX OPENING Align. OUTSIDE WIRE TIE (Loosely secure.) VEHICLE HARNESS Clean with isopropyl alcohol. ANTENNA CABLE COVER SEAL Q081706BK 36. Remove the adhesive backing from the cover seal, and attach it to the outside of the windshield, positioned over the antenna. 40. Route the antenna cable to the center panel opening as shown. 37. Cut one urethane tape as shown. ANTENNA CABLE GLOVE BOX OPENING CENTER PANEL OPENING ANTENNA PASSENGER’S A-PILLAR (Clean with isopropyl alcohol.) Q081708BK URETHANE TAPE (Cut.) Q091550AK URETHANE TAPE (Cut in step 26.) Q081707BK 38. Route the antenna cable along the passenger’s Apillar. Using five pieces of urethane tape, secure the antenna cable to the passenger’s A-pillar in the areas shown after cleaning with isopropyl alcohol on a shop towel. NOTE: Do not attach the urethane tape over any vehicle holes, pay attention to the orientation of the urethane tape. 10 of 12 AII 50687 (1311) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. www.collegehillshonda.com 41. Route the antenna cable through the center panel opening, and align it with the vehicle connector. 44. Secure the antenna cable to the vehicle panel with one wire tie with clip in the area shown. CENTER PANEL OPENING VEHICLE CONNECTOR Align. WIRE TIE WITH CLIP VEHICLE HARNESS ANTENNA CABLE WIRE TIE VEHICLE PANEL QB51801AK 42. Secure the antenna cable to the vehicle harness with one wire tie. ANTENNA CABLE GLOVE BOX OPENING Q081804BK 45. Secure the antenna cable to the vehicle frame with two wire ties. 43. Secure the antenna cable to the vehicle harness with two wire ties. ANTENNA CABLE VEHICLE HARNESS ANTENNA CABLE 2 WIRE TIES VEHICLE FRAME GLOVE BOX OPENING 2 WIRE TIES © 2013 American Honda Motor Co., Inc. – All Rights Reserved. Q081803BK QB51802AK AII 50687 (1311) 11 of 12 www.collegehillshonda.com 46. Cut one urethane tape, and wrap the piece of urethane tape around the antenna cable as shown. GLOVE BOX OPENING 48. Bundle the antenna cable, and secure it to the vehicle harness with one wire tie. ANTENNA CABLE 30 mm (1.2 in.) URETHANE TAPE (Cut.) Do not fold the antenna cable. Q091551BK 47. Secure the antenna cable to the vehicle frame with one wire tie. GLOVE BOX OPENING ANTENNA CABLE WIRE TIE (Tighten one wire tie secured in step 39.) VEHICLE HARNESS Q091552BK 49. Plug the 2-port bus cable connector to the vehicle connector. 50. Plug the antenna cable connector to the XM radio unit. VEHICLE FRAME 51. Plug the vehicle connectors to the audio unit, and reinstall the center panel. WIRE TIE 52. Check that all wire harnesses are routed properly and all connectors are plugged in. 53. Check the overlap between the headliner and the passenger’s A-pillar trim. Refer to the service manual. If necessary, adjust the overlap. 54. Reinstall all removed parts. 55. Connect the negative cable to the battery and check operation of all lights and other electrical accessories. ANTENNA CABLE Q091553AK 56. Press and hold the radio power button for two seconds to restore radio and navi (if equipped) system functions. 57. Reset the clock on vehicles without navigation. 58. Check the operation of the XM radio system according to the Accessory User’s Information Manual. 12 of 12 AII 50687 (1311) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.