Download LCD TV SERVICE MANUAL KONKA GROUP CO,LTD.
Transcript
Elenberg CTV-1540, Elenberg CTV-2065 LCD TV SERVICE MANUAL Model list KLC-TM1508 KLC-TM2018 KONKA GROUP CO,LTD. Digital Flat Display Division IMPORTANT SERVICE SAFETY INFORMATION Operating the receiver outside of its cabinet or with its back removed involves a shock hazard. Work on these models should only be performed by those who are thoroughly familiar with precautions necessary when working on high voltage equipment. Exercise care when servicing this chassis with power applied. if carelessly contacted, can cause serious shock or result in damage to the chassis. Maintain interconnecting ground lead connections between chassis, escutcheon, picture tube dag and tuner when operating chassis. When it is necessary to make measurements or tests with AC power applied to the receiver chassis, an Isolation Transformer must be used as a safety precaution and to prevent possible damage to transistors. The Isolation Transformer should be connected between the TV line cord plug and the AC power outlet. It is important to maintain specified values of all components and anywhere else in the received that could cause a rise in operating supply voltages. No changes should be made to the original design of the receiver. Components shown in the shaded areas on the schematic diagram and/or identified by in the replacement parts list should be replaced only with exact factory recommended replacement parts. The use of unauthorized substitute parts man creates may create shock, fire, or other hazards. Before returning the receiver to the user, perform the following safety checks: 1. Inspect all lead dress to make certain that leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the receiver. 2. Replace all protective devices such as non-metallic control knobs, insulating fish papers, cabinet backs, adjustment and compartment covers of shields, isolation resistor-capacitor networks, mechanical insulators etc. 3. To be sure that not shock hazard exists, a check for the presence of leakage current should be made at each exposed metal part having a return path to the chassis (antenna, cabinet metal, screw heads knobs and/or shafts, escutcheon, etc.) in the following manner. Plug the AC line cord directly into a 110V/220V/240V, AC receptacle. (Do not use an Isolation Transformer during these checks.) All checks must be repeated with the AC line cord plug connection reversed. (If necessary, a non-polarized adapter plug must be used only for the purpose of completing these checks.) PLEASE READ BEFORE ATTEMPTING SERVICE 1. Use an Isolation Transformer when performing any service on this chassis. 2. Never disconnect any leads while receiver is in operation. 3. Disconnect all power before attempting any repairs. 4. Do not short any position of the circuit while the power is on. 5. For safety reasons, replace components any with identical replacement parts (SEE PARTS LIST). 6. Before alignment, warm up the TV for at least 30 minutes. 7. When removing a PCB or related component, after unfastening or changing a wire, be sure to put the wire back in its original position. 8. Inferior silicon grease can damage IC's and transistors. When replacing IC's and transistors, use only specified silicon grease. Remove all old silicon when applying new silicon. 9. Before removing the anode cap, discharge eletricity because it contains high voltage. A. SPECIFICATION System : Colour System:PAL,SECAM Sound System:DK/BG/I/M Audio output power 10%THD 1W X 2KLC-TM1508 10%THD 2W X 2KLC-TM2018 Antenna Impedance 75(Unbalance) Power Consumption 48WKLC-TM1508 60WKLC-TM2018 Power Supply : AC~100-240V,50/60Hz (Adapter)-----KLC-TM1508 DC12V 4ATV------------------KLC-TM1508 AC~100-240V,50/60HzTV -------KLC-TM2018 item 1 2 3 4 5 5 Port list KLC-TM1508 RF cable Video and Audio S-Video Headphone audio output VGA DC 12V input item 1 2 Port list KLC-TM2018 RF cable Y Pb /Cb Pr /Cr Audio2(YPb/CbPr/Cr and PC Audio input) VGA Video and Audio1 S-Video Headphone audio output AC Power input 3 4 6 7 8 9 1.Preface 1.1 Applicable area This test manual is applicable for KLC-TM1508. 1.2 Test notes 1.2.1 Please follow the pointed test steps and choose the proper test equipment to conduct adjustment, otherwise good effect of TV set could not be obtained. Pointed bias voltage value should be ensured during test to get satisfied test result. 1.2.2 Be sure that you have the static electricity –protective glove in before test. 2 Test environment 1Temperature15~35°C 2Relative humidity 45 ~ 75% 3Air pressure: 86 ~ 106kPa 3 Test equipment 1) Computer 1 2) Oscilloscope100MHz 1 3) Multimeter (VICTOR VC9801) 1 4) DC Voltmeter 1 5) Oscilloscope Tektronix2232 1 6) :PR-602A 1 7) : Tektronix TCP300 1A TCP312W 1 8) :Tektronix ! P6015A(1000 1 9) "#$ %Agilent ! 34401A &' FLUKE 187/189 1 1) 4 T he item and method of debugging 4.1 Adjustment manual book of LCD panel Four-CCFL inverter (PCB Board P/N:35007175) 4.1.1 Test method 4.1.1.1 While mesureing the inverter ,we usually connect the high voltage probe to the output,but this will change the original path value called load effect. Most high voltage probes have 3PF capacitacne such as Tektronix P6015A,when we measure the Four-CCFL inverter,in order to balance the load effect of two sides ,we advise using two high voltage probes to measure two side outputs. 3P Tektronix P6015A 3P Tektronix P6015A CS CS OutL CCFL CP CP L OutR L CCFL 4.1.1.2 For MP1018 project,the outputs have the capacitance divider ,see figure as below,when we measure the output voltage,we may measure the parallel connection voltage value of the C722 and C730 or C724 and C731,then according to theformula Vout1=Vc1*(C722//C730)/C721,Vout2=Vc2*(C724//C731)/C723,we m ay get the output voltage value(Vc1,Vc2 means the parallel connection voltage value of the C722 and C730 or C724 and C731). At the same time ,we should pay attention to the followings : First,observe the output voltage waveform is distort or not.Second ,observe t he output waveform fr equency is between 40 kHz and 60kHz or not.Third,disconnecting any output ,observe the start-up voltage and start-up time is right or not. 4.1.1.3 Because the a ctual impedance and t heoretical impedance of the LCD panel's l amps have a little tolerance,we pay more attention to the output current in actual measurement.The LCD panel's lamps need a constant current s ource to maintain the brightness,so we may make a high frequency amperemeter in series with the low-voltage output of XS702,XS703,XS704,XS705,then adjust the input voltage equals 12V,as long as the current meets the requirement of the specification(5.5--6.5mA),it can keep the brightness of the lamps. 4.1.1.4 Force 0-5V voltage to the input port that is the third pin of XS701. Confirm if it will shut down at 0V and start at 5V. 4.2 Digital signal part KLC-TM1508 start order Turn on the power 12V N404 RESET and IO port initialize Other IC electrify, reset, initialize Turn on LCD Panel Supply Power Turn on back light lamp,Successful start 4.2.1 After turning on the power, if blank screen appears (no back light lamp), just press POWER button several times, if blank screen still there, 4.2.1.1 Check if the voltage of every power supply is normal. 4.2.1.2 Check if the crystal oscillator Z402 (14.318180MHz), Z301 (24.576MHz) oscillate or not, and oscillate frequency is right or not. 4.2.1.3 Back light control signal (BKLON) of PIN 3 of XS514 has high level (about 5V) or not, if not, chec k whether fault sold ered or short circui t happened to Q504,R580,R588. 4.2.2 If back light lamp lights but no screen displays,check N404 reset circuit and crystal oscillator output to make sure CPU is under work, if CPU is under work, then check signal channel. Signal channel is composed of two parts: Video channel (including antenna, AV, S-terminal input) and RGB channel for PC. If no picture displays or bad code displays when input either of these two channel signal in turn, control signal maybe wrong, then use oscilloscope to check waveforms at test points DEN, DVS, DHS and DCLK are normal or not following the rule from back to front. 4.2.3 If just picture color has problem, then shift input to RGB input, and output R,G,Bmono signal from computer to find the wrong color, then use oscilloscope to test XS504 pin to find the wrong data cable following the same order. 4.2.4 If just video channel has problem, check N301 signal output VCLK,V-Hs, V-Vs(TEST POINT), control signal -DVS DHS DCLK and DEN output from movement compensation N404have waveform or not to find the problem. 4.3 IF Channel adjustment 4.3.1 Preparation steps 4.3.1.1 Connect (+) of RF of TV signal generator PM5518 to Pin 11 of RF TUNER N1000, (-) to Pin 3 of RF TUNER N1000. 4.3.1.2 Set TV signal generator PM5518 RF output to the maximum. 4.3.1.3 Set TV signal generator PM5518 RF Output to 38.0MHz, and set video output signal of this signal generator to gray scale. 4.3.1.4 Connect DC Voltmeter “+” to Pin 8 of N1000, - to RF TUNER cabinet. 4.3.1.5 Connect oscilloscope probe + to Pin 10 of XP6010, - to RF TUNER cabinet, then set oscilloscope to 50mV/div Time/div TV-H( s), and set to TV-H simultaneously. 4.3.1.6 Connection between TV board and TESTER is shown as the following figure (4). 4.3.2 Adjustment steps 4.3.2.1 Plug the power cord. 4.3.2.2 Turn T1000 magnetic core with ceramic aligner screwdriver so that reading on DC Voltmeter is 2.5V 0.2V. 4.3.2.3 Waveform of T2 on the oscilloscope can be observed as the figure (5) shown. 4.4 AGC adjustment 4.4.1 Preparation steps 4.4.1.1 Connect TV board whose IF has been adjusted to Power board motherboard (Do not install TV board into the back cabinet). 4.4.1.2 Set TV signal generator to 56 channel (855.25MHz), apply RF half color bar signal and input to ANTENNA INPUT of RF 4.4.1.3 Connect (+) end of DC Voltmeter to Pin 1 of N1000 of RF Pin 3 of RF TUNER. 4.4.2 Adjust steps and 62dB 3dB TUNER. TUNER, (-) end to 4.2.2.1 Check if connections connect well, start automatic searching. 4.2.2.2 Press PROG. / button to display the channel you hav e received on the scre en after automatic searching finishing. 4.2.2.3 Adjust VR1000 with small screwdriver so that DC Voltmeter is within 2.0V – 2.5V(maximum),then reverse VR1000 and just make c onfusi onal of noi se disappear on the picture. 4.5 White calibration adjustment 1 Receive black or white signal under AV or PC mode, adjusting brightness and contrast to set the brightness to 15Nit in dark area and 90 Nit in bright area. 2 Adjust white balance.Press(MENU”button once, then press “PRE.CH”five times to enter factory menu, select “Temp” Menu, Adjust Red 0-100 Green 0-100 Blue 0-100 3 Adjusting chromaticity coordinates of black and white to fit the requirement (X=0.313, Y=0.329), or plug automatic calibration system to adjust white calibration automatically. KLC-TM2018 1.Preface 1.1 Applicable area This test manual is applicable for KLC-TM2018. 1.2 Test notes 1.2.1 Please follow the pointed test steps and choose the proper test equipment to conduct adjustment, otherwise good effect of TV set could not be obtained. Pointed bias voltage value should be ensured during test to get satisfied test result. 1.2.2 Be sure that you have the static electricity –protective glove in before test. 2 Test environment 1Temperature15~35°C 2Relative humidity 45 ~ 75% 3Air pressure: 86 ~ 106kPa 3 Test equipment 1) Computer 2) Oscilloscope100MHz 3)Multimeter (VICTOR VC9801) 4)DC Voltmeter 5)Oscilloscope Tektronix2232 6)Cement Resistance 7)Test Clamp 8TV signal generator 1 1 1 1 1 1 1 1 4 .T est i tem a nd met ho d 4.1 Power Supply Board 4.1.1 The input and output characteristic test of power 4.1.2 Intention of test: Check input and output to find if short circuit. 4.2 checking method: use Multimeter (VICTOR VC9801) of Number 1 Item The resistor of AC resistor to check Test Point Standard AC Input Connector XS901 No short input 2 The resistor of V12 circuit V12 output of connector XS902 output 3 The resistor of V12 No short circuit Between the pins of C908 assistant power output No short circuit Please check short circuit point on the PCB board if you find short circuit. 4.2.1 Test after supply AC 220V 4.2.2 Intention of test: 4.2.3 Supply AC 220V step by step,then the circuit start to work 4.2.4 Test the voltage of output 4.2.5 Short output test 4.2.6 The Peak-Peak value yawp test of the power output 4.2.7 The test of turning on and off TV 4.2.8 Checking method 4.2.9 Test the empty loading output of power supply Fix the power supply board on Test clamp unconnecting the load then input 220VAC and turn on power switch to test the output voltage by multimeter Number Ietm Test point Empty loading 1 V12 voltage Output of V12 0.0A Listen if there is deviant noise at the same time. Standard 12.0V 0.48 4.2.10 Test the rated load output voltage Turn off the power then connecting the load on output and turn on the power to test the output voltage by multimeter Rated load output voltage / current are as follows: Number Item Current standard 1 V12 s rated load 5A Listen if there is deviant noise at the same time. Voltage standard 12.0V 0.48 4.2.11 Test of V12 s shorting-output protect Make the output shorted in 3 seconds the output voltage should be 0V.after relieving the short ,turn off the power and discharge the input filter capacitor C904 10 seconds by discharge resistance (cement resistance 2-5W510 ),then supply the power again using multimeter to test the output of power The output voltage should come back normally 12.0V 0.48 4.2.12 The test of powers peak-peak value yawp output Under the rated load Initialize the oscill oscope 50mV per unit and parallel-connect 0.1UF and 10UF capaci tor on probe to see the output ripple is OK or not. Number 1 Item 12V output Test point V12 output Standard 150mV 4.2.13 The fully loading and empty loading experiment of turning on/off TV Turn on/off TV per 5 times every 5 seconds under the two states .Make sure if the ou tput is OK or not. 4.2.14 The standard of power aging experiment Every product should aging 8 hours under rated load and 45 C Make sure the output voltage is in regular range. 4.3 Digital signal part 4.3.1 Digital signal board power part 4.3.2 Verify the state of TV set Please switch the TV on by “Power on/off” switch,then verify the LED color of touch button.If it is red(standby state),the back-end power has been shut off(the voltage of N802 No.5 pin is 0V),the supply power for IC-chip has been shut off except N803 normally working.Please test the voltage of D616 is 5V to verif y the power of N803 no rmal on standby state. 4.3.3 Checking Supply Power. If the color of LED is green,the power supply for signal board(Test the Number 5,6,7,8 pin of N802 v oltage is 12V).N801 supply 5V power(Test the anode of C853).N 810 N811 supply 3.3V(Tes t the No.2 pin),N812 N813 supply 1.8V(T est the No.2 pin)for main IC N407,N305. 4.3.4 Digital signal part KLC-TM2018 start order Turn on the power N407 RESET and IO port initialize Other IC electrify, reset, initialize Turn on back light lamp Successful start and LOGO display 4.3.5 After turning on the power, if blank screen appears (no back light lamp), just press POWER button several times, if blank screen still there 4.3.6 Check if the voltage of every power supply is normal. 4.3.7 Check if the cr ystal oscillator Z4. 1(14.318MHz)oscillate or not, and oscilla te frequency is right or not. 4.3.8 Back light control signal (BKLON) of PIN 3 of XS512 has high level (above 3.5V) or not, if not, check whether fault solder ed or short circuit h appened to V507, R559 , R560,R561 4.3.9 If back light lamp is on while there is no display,check N407’s reset circuit and the output of the oscillator to confirm the CPU is working or not.If CPU is working ,then checking the signal channel. Signal channel has been divided into two parts, general video channel(including antenna, AV, S-terminal input, Y, Cb, Cr) and HDTV channel (Includi ng Y Pb Pr and RGB). I f no any picture disp lays or bad code disp lays when switching between these two channels, control signal may be wrong. Please use oscilloscope to check test point DEN, DVS, DHS and DCLK from end to front to find whether waveform displayed on the oscilloscope or not, if not, check if fault solder or short circuit happ ened.If just picture color has problem, sw itch INPUT to RGB inp ut, then input R, G, B mon ochrome signal separately from computer to find the problem col ors. Check data line of XS504 with oscilloscope according to the above form to find it’s problem. DCLK Waveform DEN Waveform DHS Waveform DVS Waveform 4.3.10 If only one channel has problem check the signal of this channel normal or not.AV1,AV2,S-Video,Y,Cb,Cr are inputted from analog signal board to digital signal board RGB Y Pb Pr(digital signal board)are input N407 by N603.Using oscilloscope to check ICN1003’s output signal TV-Y,TV-Cb,TV-Cr,TV-HS,TV-VS(1 3 5 7 8pin of XP1005),to verify the waveform is right or not.If not ,check whether fault soldered or short circuit are happened Else ,check the 5V supply voltage of N601,N603 on digital signal board As the Above order we may find the problem of RGB Y Pb Pr video signal Output a color bar signal to AV1 by signal generator PM5518,check the waveform if normal or not with oscilloscope. CVBS color bar Wave form TV_Y Waveform XP 10 05 ’s 1 Pin TV_ Cb Waveform XP1005’s 3 Pin T V_ Cr Waveform X P10 05 ’s 5 Pin TV _H s Waveform X P10 05 ’s 7 Pin T V_V s Wavrform XP1005’s 6 Pin 4.4 Analog signal board 4.4.1 Analog signal board power part Analog signal board is supplied by 12V transformed to 5V by N1101,N1815 After connecting the power ,check the voltage of N1101’s 2 pin with multimeter to see if the voltage of C1809 ‘s anode is right(about 5V) or not This is the back-end IC’s normal power supply. 4.4.2 IF channel AFC adjustment on analog signal board Input a 38MHz IF Signal generated from TV signal generator to RF TUNER according IF cable whose one side to 11 pin of RF TUNER and the other to 3 pin of RF TUNER(GND). IF channel AFC of LC-TM2018 has been adjusted automatically by software which may check the power supply of IF IC is normal or not See if the anode voltage of C2224 is 5V or no t and check N1006 s 21 pin voltage is 2 .5 0.2V If not check whether fault soldered or short circuit happened to R2029,R2030. 4.4.3 AGC adjustment on analog signal board 4.4.4 Preparation steps 4.4.5 Connect TV board whose IF has been adjusted to Power board and motherboard . 4.4.6 Set TV signal g enerator to 56 channel (855.25MHz), apply RF 62dB 3Db half color bar signal and input it to ANTENNA INPUT of RF TUNER. 4.4.7 Adjust steps 4.4.8 Check if connections connect well, start automatic searching. 4.4.9 Press PROG. -/. button to display the channel you have received on the screen after automatic searching finishing. 4.4.10 Press factory menu button to display factory menu on TV and select TB1274 ,press PROG +/- button to select the tda9885 AGC item of sub-menu ,then press volume +/- but ton to adjust the val ue until the snows ar e disappear The value after adjusting is about 12-16 and the tuner voltage of first pin is about 2.0 0.2V. 4.5 White calibration adjustment 4.5.1 Receive black or white signal under AV or PC mode, adjusting brightness and contrast to set the brightness to 5 Nit in dark area and 90 Nit in bright area. 4.5.2 Adjust white balance. Enter factory menu, select cal. Menu, and swap color temp item to user. Adjust Red 0-255 Green 0-255 Blue 0-255 4.5.3 Adjust black balance. Enter factory menu, and select TB1274 Menu. Adjust Red offset 0-127 Blue offset 0-127 4.5.4 Adjusting chromaticity coordinates of black and white to fit the requirement (X=0.304, Y=0.325), or plug automatic calibration system to adjust white calibration automatically. Trouble Shooting Key IC listKLC-TM1508 Item Type Maker 1 PQ05RD11 Sharp 2 3 4 5 6 7 8 9 10 11 12 14 TDA1517P PHILIPS 24LC16B/SN MICROCHIP AT24C16AN-10SI-2.7 ATMEL 74LVC541APW 74LVC32A D AM29LV800DT-70EC-AMD/# PHILIPS PHILIPS AMD MX26LV800BTC-55-3/# MXIC 1117-1.8V 1117-3.3V MP1410ES-LF-SOIC-8-MPS SAA7114H PW130-10Q 1117 serial 1117 serial MPS PHILIPS PIXELWOR KS PHILIPS MICRONAS ROHM MRT MPS Qingjia TDA9808T MSP3463G BA033FP-ROHM M385 LVDS MP1018EM Tuner-AFT1/6000 Package Circuit No. Qty. N1001 HDIP18 N2001 1 1 SOIC-8 N309 1 TSSOP-20 SO-14 TSOP-48 N514 N608 N307 1 1 1 SOT223 SOT223 SOIC-8 LQFP100 208PQFP N810*N811 N812*N817 N815 N301 N404 2 2 1 1 1 SO20 PMQFP64 N1010 N2000 N818 N502 N701 N1000 1 1 1 1 1 1 Circuit No. Qty. TSSOP-56 TSSOP28 Key IC listKLC-TM2018 Item Type Maker 1 PQ05RD11 Sharp 2 3 4 TDA1517 PHILIPS 24LC16B/SN MICROCHIP AT24C16AN-10SI-2.7 ATMEL 74LVC541APW PHILIPS Package N1101 1 SIL9MPF N2001 1 SOIC-8 N306 1 TSSOP-20 N508 1 5 6 7 8 9 PIC12F629 74LVC273A AM29LV800DT-70EC-AMD/# MICROCHIP PHILIPS AMD AM29LV800BB-90EI-AMD/# AMD 1117-1.8V 1117-3.3V MP1410ES-LF-SOIC-8-MPS TB1274AF 1117 serial 1117 serial MPS TOSHIBA 10 11 12 14 TC90A69F TOSHIBA TDA9885T MSP3463G 74HC4052D PW1306 PHILIPS MICRONAS PHILIPS PIXELWOR KS PHILIPS FAIRCHILD PERICOM INFINEON Sharp FAIRCHILD Qingjia 74LVC14A FSAV330 PI5V330 E3DS01 PC817B KA431Z Tuner-AFT1/6000 SOIC-8 TSSOP-20 TSOP-48 N803 N509 N305 1 1 1 SOT223 SOT223 SOIC-8 QFP48-10 14-0.8 SOP16-P300-1.27 N813*N812 N810*N811 N1815*N801 N1003 2 2 2 1 SO24 PMQFP64 SO16 208PQFP N1006 N2000 N602 N407 SO14 TSSOP16 QSOP16 1 N1004 N629 N603 N601 N901 N902 N903 N1000 1 1 1 1 1 2 1 1 1 1 1 2 3 4 5 3.3VADC KLC-TM1508 Digital Board schematic circuit diagram 6 V33D 3.3VADC L306 FB V33A C306 0.1uF C334 C333 0.1uF D C332 0.1uF C313 0.1uF C328 0.1uF C305 0.1uF C321 0.1uF C327 0.1uF C326 0.1uF C323 0.1uF C304 0.1uF V33A R305 100 22uF_10V_T C314 0.1uF C309 0.1uF FB L307 C302 0.1uF R304 C324 0.1uF SCL SDA D 100 V33D C338 C337 0.1uF C322 22PF 22uF_10V_T XS303 5 24.576MHz 10 12 C320 14 0.1uF R309 Vedio-Input 18 R306 C316 16 AI23 AI22 SAA7114H AI21 0.1uF B TV-INPUT R302 2.2K TV_IN TP1 to PW130-55pin XPD7 XPD6 XPD5 XPD4 XPD3 XPD2 XPD1 XPD0 TEST0 TEST1 TEST2 RTCO RTS1 RTS0 0 R315* L301 3.3uH 3.3K C303 100PF R316* 3.3K B 0 R303 R321* 3.3K V-VS V-HS D301 IN4148 R301 RP304* VCLK 30 V-VS1 TP V-HS1 TP 33x4 V656-0 V656-1 V656-2 V656-3 V656-4 V656-5 V656-6 V656-7 4.7K XS311 V656-[0..7] R319 0 R318 V33D CON13 RP302 33x4 R313 30 C R317 FB AUX5V(5V) 81 82 84 85 86 87 89 90 L302 44 73 74 SDA SCL RES 0.01uF RESETn AI1D 27 1 2 3 4 5 6 7 8 9 10 11 12 13 C315 0.01uF 36 35 34 C319 XS301 AI11 30 19 LLC LLC2 20 0.1uF 28 29 C310 R310 56 Vssde1 Vssde2 Vssde3 Vssde4 Vssx Vssdi3 Vssdi2 Vssdi1 R311 56 AI12 26 50 76 100 5 88 63 38 R308 56 AI2D Vssa0 Vssa1 Vssa2 AGND R307 56 18 24 15 9 21 13 C307 0.1uF CE 18 7 6 31 32 22 77 78 79 72 71 70 69 67 66 65 64 1 25 51 75 33 43 58 68 83 93 8 23 17 11 AI24 33x4 V656-7 V656-6 V656-5 V656-4 V656-3 V656-2 V656-1 V656-0 XTALI XTALO 18 RP301 XRH XRV XRDY XDQ XCLK XTRI XTOUT Y SCL SDA AOUT R312 video in N301 SAA7114H 54 IPD7 55 IPD6 56 IPD5 57 IPD4 59 IPD3 60 IPD2 61 IPD1 62 IPD0 42 ITRDY 45 ICLK 46 IDQ 47 ITRI 48 IGP0 49 IGP1 52 IGPV 53 IGPH 37 AMCLK 39 ASCLK 40 ALRCLK 41 AMXCLK 92 91 96 95 94 80 4 18 C 1 2 3 4 5 6 C R314 TEST3 TEST4 TEST5 AV 3.3uH HPD0 HPD1 HPD2 HPD3 HPD4 HPD5 HPD6 HPD7 XS302 CON10 L304 Vddde1 Vddde2 VDDDE3 Vddde4 Vdddi1 Vdddi2 Vdddi3 Vdddi4 Vdddi5 Vdddi6 Vddx S Vdda0 Vdda1 Vdda2 Y 100PF 98 99 97 3 2 C C329 22PF Z301 C311 3 1 TCK TMS TRST TDI TDO 4 2 V33D V33A C301 1uF_6V_T RP303* 33x4 V656-[0..7] RCA-8 LCDON A A Title DYNAX ELECTRONICS(HK)LTD. Size Number Revision Orcad B Date: File: 1 2 3 4 5 29-Mar-2005 Sheet of E:\EE\LC-TM1580P\原理图\decoder1.sch Drawn By: 6 1 2 3 4 V33 R876 V33 R877 DRE3 DRE4 DRE5 DRE6 DRE7 DGE[0..7] 4 6 7 11 12 14 8 10 DGE0 DGE1 DGE2 DGE3 DGE4 DGE5 DGE6 DGE7 DBE[0..7] 15 19 20 22 23 24 16 18 DBE0 DBE1 DBE2 DBE3 DBE4 DBE5 DBE6 DBE7 27 28 30 25 DHS C DVS DEN 31 DCLK G0 G1 G2 G3 G4 G5 G6 G7 32 26 PWDN VCC 9 VCC OUT1 OUT1 OUT2 OUT2 N502 OUT3 OUT3 DS90C383A CLKOUT CLKOUT R880 FB 47 48 TXE3P C570 0.1uF TXE0P TXE0M 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 100uF_6V_T TXECP TXE2P TXE1P 45 46 TXE1P 41 42 TXE2P TXOCP TXE2M TXO2P TXE0P TXE1M TXO3P TXO1P 37 38 TXE3P 39 40 TXECP TXO0P TXE3M 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 D TXE3M TXECM TXE2M TXE1M TXE0M TXO3M TXOCM TXO2M TXO1M TXO0M TXECM GND GND V33 VNN VOO LVDSVC LVDSGD LVDSGD LVDSGD HSYNC VSYNC ENABLE CNTRL CLOCK XS504 LVDS C557 OUT0 OUT0 B0 B1 B2 B3 B4 B5 B6 B7 V33 VPANEL L516 44 36 43 49 V33 VOO GND VNN C L514 PLLVCC PLLGND PLLGND GND GND GND GND GND DRE2 LCDON 34 33 35 FB L515 FB C565 C542 0.1uF 10uF_6V_T C525 0.1uF C518 0.1uF C539 0.1uF V33 5 13 21 29 53 DRE1 R0 R1 R2 R3 R4 R5 R6 R7 R/F 51 52 54 55 56 3 50 2 DRE0 17 D VCC 1 DRE[0..7] GND R879 GND GND R878 V33 GND R879 LCDON V33 32 26 9 1 GND DRO3 DRO4 DRO5 DRO6 DRO7 DGO[0..7] DGO0 DGO1 B DGO2 DGO3 DGO4 DGO5 DGO6 DGO7 4 6 7 11 12 14 8 10 DBO[0..7] DBO0 DBO1 DBO2 DBO3 DBO4 DBO5 DBO6 DBO7 DHS DVS DEN 27 28 30 25 31 G0 G1 G2 G3 G4 G5 G6 G7 PWDN VCC VCC OUT0 OUT0 OUT1 OUT1 OUT2 OUT2 N503 OUT3 OUT3 DS90C383A CLKOUT CLKOUT B0 B1 B2 B3 B4 B5 B6 B7 LVDSVC LVDSGD LVDSGD LVDSGD HSYNC VSYNC ENABLE CNTRL CLOCK 47 48 TXO0P 45 46 TXO1P 41 42 TXO2P 37 38 TXO3P 39 40 TXOCP C543 0.1uF C531 0.1uF C540 0.1uF C517 0.1uF C512 0.1uF C558 0.1uF C535 0.1uF C536 0.1uF TXO0M TXO1M GND TXO2M Bypass caps for U14 B VOO is 3.3V LVDS power for U13 and U14. TXO3M TXOCM VOO 44 36 43 49 GND 17 DCLK 15 19 20 22 23 24 16 18 R0 R1 R2 R3 R4 R5 R6 R7 GND GND GND GND GND DRO2 51 52 54 55 56 3 50 2 5 13 21 29 53 DRO1 R/F DRO0 VCC DRO[0..7] PLLVCC PLLGND PLLGND VNN 34 33 35 GND A A GND GND Title DS90C383.SCH Size Number Revision B Date: File: 1 2 3 29-Mar-2005 Sheet of E:\EE\LC-TM1580P\原理图\Ds90c3831.SCH Drawn By: 4 1 2 3 4 5 6 R627* OPEN D609 DIODE TXD VCC R628* OPEN RXD V_DDC_5V D610 DIODE D R632* 10K VCC 7 VCLK 6 5 DDC_CLK 2 2 DDC_DAT NC1 NC2 NC3 SCL SDA GND R629* 10K R630* 10K 3 3 D605* BAV99L D606* BAV99L 8 1 2 3 C675* 0.1uF 4 R635 NC R634 L617 R666 C682 56pF 75 VSYNC1 VSYNCRTN HSYNC1 AHSYNC R636 NC RXD 14 VSYNC1 13 HSYNC1 10 4 N608C N608B 6 8 9 74LVC32 5 0 C 74LVC32 V33 2 2 BAV99L D602 BAV99L D603 3 R640 2.2K IT NEED 3.3V POWER V33 2 V33 BAV99L D604 3 3 12 DDC_DAT 1 1 11 1 R668 0 U1C1 75 V33 15 DDC_CLK AVSYNC C678 56pF HSYNCRTN R642 XS607 10 5 9 4 8 3 7 2 6 1 3 N608A 2 TXD C C693 0.1uF 1 24LC21A 1 1 0 R641 2.2K 74LVC32 L618 R667 V33 V33 14 R9U2 N605* 7 D VGA_R VGA_G VGA_B DB15-VGA L609 L611 L613 40OHM@100MHZ 40OHM@100MHZ 40OHM@100MHZ B R626 75 V_DDC_5V R625 75 L608 40OHM@100MHZ RAIN L610 40OHM@100MHZ GAIN L612 40OHM@100MHZ BAIN B R623 75 C661 12P C656 12P C652 12P XS606 1 2 3 4 5 6 7 8 9 10 11 12 13 14 A HSYNC1 VSYNC1 VGA_B VGA_G VGA_R VGA-Input DDC_DAT DDC_CLK RXD TXD A DB15-VGA Title GRAPHICSIN.SCH Size Number Revision Orcad B Date: File: 1 2 3 4 5 29-Mar-2005 Sheet of E:\EE\LC-TM1580P\原理图\GRAPHICSIN1.SCH Drawn By: 6 1 2 ROMOEn 3 V33 4 V33 26 28 11 12 14 47 RESETn D R349 U3WPn 100K V33 R346 0 A2 A3 A4 A5 V33 CE OE WE RP WP BYTE 25 24 23 22 21 20 19 18 8 7 6 5 4 3 2 1 48 17 16 A1 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 VPP VCC C391 0.1uF R347 13 C388 37 0 100K D[0..15] D[0..15] 0.1uF D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 D16 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 29 31 33 35 38 40 42 44 30 32 34 36 39 41 43 45 D D0 SDA SCL D1 D2 D3 V33 D4 D5 C390 100uF D6 D7 NMI NMI Pushbutton D8 D9 D10 D11 D12 D13 D14 D15 V33 XS310 GND1 GND2 46 27 V33 V33 R356 C383 0.1uF Flash_8M ROM C 6 R345 N307 ROMWEn 5 N309 6 5 3.3K XS309 4 2 FCEn V33 R343 3.3K 4 2 1 2 3 3 1 SCL SDA NC0 NC1 NC2 VCC WP GND C397 0.1uF 8 R351 30K C v33 C396 0.1uF 7 3 1 4 24C16 NVRAM V33 R352 3.3K RESETn A[1..19] V33 V33 C398 18PF XS313 A2 A4 B A6 A9 A11 A12 A14 A17 A19 ROMOEn D15 D14 D5 D4 D3 D2 D9 D8 A GND 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 A1 A3 B A5 V33 A7 A8 A10 R357 IRPn ICEn 3.3K A13 A15 A16 A18 R360 IA20 IA21 ROMWEn 3.3K R359 3.3K D7 D6 D13 D12 D11 D10 D1 D0 A Title MEMORY.SCH Size HEADER 30X2 Number Revision Orcad B Date: File: 1 2 3 4 5 29-Mar-2005 Sheet of E:\EE\LC-TM1580P\原理图\Memory1.SCHDrawn By: 6 1 2 3 V33 V33 V33 V33 V33 4 V33 V33 V33 V33 V33 5 6 V33 CS0n RDn D D V33 R5053 470 XS611 8 HEADER R561 10K R562 470 R554 10K R566 10K R567 10K R569 10K R574 10K R568 10K R563 10K N514 1 19 RP501 33x4 1 2 3 4 5 6 7 8 KEY_0 KEY_1 KEY_2 KEY_3 KEY_4 KEY_5 KEY_6 V33 VCC D14 D9 C508 D11 VCC D13 XS605 0.1uF D15 4 3 2 1 10 GND V18 TXD RXD 4 R875 10K 1% Vin ADJ Vo2Vo4 4 Vin Vo2Vo4 XS817 D2006-4A R871 1.5K 3 1 15uH LM1117-1.8 C800 0.1uF C830 0.1uF L827 N811 Vin R870 30K N812 LM1117-3.3V 1 L802 FB1206 K 12V 5 3 MP1410ES FB Vo2Vo4 GND 6 N810 LM1117-1.8 3 COMP AUX5V C811 180PF ADJ 2.75W @ 12V max. SW 7 22uF_6V_T 2 4 470uF_16V_T 0.22uF EN 1 C818 IN Vin C820 N/C C899 4 3 5A BS Vo2Vo4 2 4.7uH(OPEN) C801 0.1uF ADJ XS816 D2006-4A 10nF C812 3.3nF R872 390K 8 V18A 100uF_6V_T 2 N815 1 0.1uF 3 L801 FB1206 F801 N817 LM1117-3.3V TO VPENAL V12 C C807 L824* 470 5A F801 Sleep Mode 200mW @ 12V max. V33 C805 2 12V 470 R555 C817 POWER INPUT LED2 D12 4 R558 Q501 BC847 C695 0.22uF L826 FB1206 AUDIO POWER V33 D10 GND Q502 BC847 XS815 B LED1 D8 74LVC541A_PW Input Buffer ADJ LCD 4.5W @ 12V +Backlight Requirement 1 2 3 4 18 17 16 15 14 13 12 11 GND PANEL-LED2(GRE) HEADER 6 1 2 3 4 D[0..15] 20 PANEL-LED1(RED) XS615 C O0 O1 O2 O3 O4 O5 O6 O7 GND GND IRRCVR VCC I0 I1 I2 I3 I4 I5 I6 I7 1 TO IRRCVR R665 4.7K STB 1 2 3 4 5 6 RP502 33x4 2 3 4 5 6 7 8 9 OE1 OE2 2 TO KEYBOARD R564 10K 3.3VADC 3.3VADC 700ma max. C804 C806 22uF_6V_T 0.1uF D808 VCC L825 FM5820 B VCC A FB C809 1000uF_16V_T C810 0.22uF C813 0.1uF A A Title MISC Size Number Revision Orcad B Date: File: 1 2 3 4 5 29-Mar-2005 Sheet of E:\EE\LC-TM1580P\原理图\Misc11.SCH Drawn By: 6 1 2 PV1 3 4 5 6 R422* R431 3.3K V33 V33 R28C11 TESTEN 47nF C455 1nF BAIN IGREEN C454 47nF ISOG C460 43 44 50 IBLUE AVSYNC 64 AHSYNC 65 7 8 10 11 13 14 C 16 17 V656-[0..7] R439 5 430 V656-0 V656-1 V656-2 V656-3 V656-4 V656-5 V656-6 V656-7 63 62 61 60 59 58 57 56 TP1 TP1 TP C441 22P VCLK 55 72 R419 3.3K 137 TESTEN R450 R448 3.3K 3.3K FILTER RESETn RED GREEN 132 RXD TXD SOG BLUE 53 54 SDA SCL VS RX2P RX2M RX1P RX1M N404A RCP RCM PORTA0 PORTA1 PORTA2 PORTA3 PORTA4 PORTA5 PORTA6 PORTA7 194 NMI V656_0 V656_1 V656_2 V656_3 V656_4 V656_5 V656_6 V656_7 R444 NMI 169 170 1.5M XI XO X607 X608 C494 VPEN VCLK 30PF C484 0.1uF V18 C447 Sleep Mode 9ma max. 3.3VADC V33 C485 0.1uF 3.3VDVI C477 0.1uF 22 24 26 PVD11 PVD12 PVD13 PGND11 PGND12 PGND13 VDD11 VDD12 VDD13 VDD14 VDD15 VDD16 1 3 20 75 95 135 146 173 184 6 18 68 83 104 122 133 171 186 32 33 36 39 41 46 48 52 VDDQ31 VDDQ32 VDDQ33 VDDQ34 VDDQ35 VDDQ36 VDDQ37 DVDD31 DVDD32 Power and Ground 21 25 27 C479 0.1uF N404D A8 A9 A10 A11 A12 A13 A14 N404B A15 A16 A17 A18 A19 D0 D1 D2 DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 Display Port D3 D4 D5 D6 D7 D8 D9 D10 D11 DGR0 DGR1 DGR2 DGR3 DGR4 DGR5 DGR6 DGR7 D12 D13 D14 D15 196 195 197 198 199 200 DG0 DG1 DG2 DG3 DG4 DG5 DG6 DG7 RDn ROMOEn ROMWEn CS0n PW130 DGG0 DGG1 DGG2 DGG3 DGG4 DGG5 DGG6 DGG7 L422 FB PV1 DGB0 DGB1 DGB2 DGB3 DGB4 DGB5 DGB6 DGB7 PVDD DCLKn DVS DHS DEN DRE[0..7] D DRE0 DRE1 DRE2 RP406 33x4 DRE3 DRE4 DRE5 DRE6 DRE7 RP407 88 87 86 85 82 81 80 79 DGE[0..7] 33x4 DGE0 DGE1 DGE2 RP408 33x4 DGE3 DGE4 DGE5 DGE6 DGE7 DBE[0..7] 78 77 74 73 71 70 67 66 RP409 33x4 DBE0 DBE1 DBE2 RP410 33x4 DBE3 DBE4 C DBE5 DBE6 DBE7 DRO[0..7] 131 130 129 128 127 126 125 124 RP416 33x4 DRO0 DRO1 DRO2 DRO3 DRO4 DRO5 DRO6 DRO7 DGO[0..7] 121 120 119 118 117 116 115 114 113 112 111 110 109 108 100 99 RP415 33x4 DGO0 DGO1 DGO2 RP414 33x4 DGO3 DGO4 DGO5 DGO6 RP413 33x4 DGO7 DBO[0..7] DBO0 DBO1 DBO2 B DBO3 RP412 33x4 DBO4 DBO5 DBO6 DBO7 RP411 DVDD11 DVDD12 DVDD13 3.3VADC 3.3VADC A PW130 L423 FB DGND11 DGND12 DGND13 C481 0.1uF VSS11 VSS12 VSS13 VSS14 VSS15 VSS16 C486 0.1uF 76 96 136 147 174 185 C468 0.1uF V33 A7 RP405 98 97 94 93 92 91 90 89 R420*33 R417 33 R416 33 R41533 33x4 33x4 LV1 DGND31 DGND32 DGND33 C462 0.1uF V33 A6 PW135 MPV1 9 12 15 C444 0.1uF V33 C449 0.1uF VSSQ31 VSSQ32 VSSQ33 VSSQ34 VSSQ35 VSSQ36 VSSQ37 C446 0.1uF V33 C450 0.1uF 69 84 105 123 134 172 187 C448 0.1uF V33 C453 0.1uF AVDD31 AVDD32 AVDD33 AVDD34 AVDD35 AVDD36 AVDD37 AVDD38 V33 C459 0.1uF AGND31 AGND32 AGND33 AGND34 AGND35 AGND36 AGND37 AGND38 AGND39 V33 C464 0.1uF DR0 DR1 DR2 DR3 DR4 DR5 DR6 DR7 40ma max. 90ma max. 34 35 38 40 42 45 47 49 51 C463 0.1uF 350ma max. A5 DV1 DPV1 40ma max. 3.3VADC 3.3VADC 3.3VADC 3.3VADC 3.3VADC 3.3VADC L420 FB FB 2 4 19 C480 0.1uF 167 C487 0.1uF MPLLVDD1 C476 0.1uF MPLLVSS1 0.1uF C471 0.1uF 165 C445 0.1uF L421 FB L419 DPLLVDD1 V18 DPLLVSS1 V18 168 V18 Sleep Mode 35ma 166 V18 A4 V18A 175ma max. V18 A3 C492 30PF V18 B 160 159 158 157 156 155 154 153 152 151 150 149 148 145 144 143 RD WR ROMOE ROMWE CS0 CS1 XTAL14.31818 Z402 A2 D[0..15] D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 TRST TCK TMS TDI TDO Graphics andVideo Port RTERM PW131Misc N404C 142 141 140 139 138 PW130 RX0P RX0M RXD TXD 208 207 206 205 204 203 202 201 LCDON BKLON LED1 IRRCVR LED2 PWMOUT HS RESETB 28 29 GAIN 37 IRED R418 3.3K A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 C466 0.1uF C469 0.1uF C467 0.1uF C489 0.1uF C472 0.1uF ALVDD11 ALVDD12 GFILT C451 DCLK DCLKNEG DVS DHS DEN A1 DCLK 33 106 107 101 102 103 ALGND11 ALGND12 C474 39nF 23 193 192 191 190 189 188 183 182 181 180 179 178 177 176 175 164 163 162 161 A Title 30 31 D 47nF V33 V33 A1..19] C473 3.9nF RAIN 100_NS(OPEN) R424 R433 0 PW135.SCH Size Number Revision Orcad B Date: File: 1 2 3 4 5 29-Mar-2005 Sheet of E:\EE\LC-TM1580P\原理图\Pw135-1.SCHDrawn By: 6 1 2 3 4 6 5 D D VCC PWMOUT LCDON Q506 BC847(SOT-23) BKLON R581 R579 10K 10K C563 C519 DBO[0..7] R583 NC 0.1uF VCC 0.1uF 4.7K DRO[0..7] DRE[0..7] R588 R572 VCC Display Output V12 FROM L826 XS504 DRE1 DRE3 DRE5 DRE7 DGE1 DGE3 DGE5 DGE7 DBE1 DBE3 DBE5 DBE7 B 39 37 35 33 31 29 27 25 23 21 19 17 15 13 11 9 7 5 3 1 40 38 36 34 32 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2 HEADER 20X2 C509 100uF_16V_T XS506 DEN DRO1 DRE0 DRO3 DRE2 DRO5 DRE4 DRO7 DRE6 DGO1 DGE0 DGO3 DGE2 DGO5 DGE4 DGO7 DGE6 DBO1 DBE0 DBO3 DBE2 DBO5 DBE4 DBO7 DBE6 31 29 27 25 23 21 19 17 15 13 11 9 7 5 3 1 32 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2 C521 100uF_16V_T DRO0 DRO2 NC R571 10K 0.1uF NC C530 R576 4.7K 0.1uF N516 1 8 2 7 3 6 4 DRO4 DRO6 10K U805 BA033FP(TO252-3) 1 Vi GND 0.1uF 5 R577 DGO2 DGO6 DGND DBO0 1 DBO6 C523 0.1uF R585 10K VPANEL L526 FB C515 C522 0.22uF N517 8 2 7 3 6 4 5 XS517 D2006-5A AUX5V B C524 10uF/10V R575 300 9435A D507 LED V5V 0 R572 OPTIONAL FOR 3.3V DRIVE PANEL V33PANEL OPTIONAL FOR 3.3V DRIVE PANEL 0 R571 Q505 BC847(SOT-23) OPTIONAL FOR 5V DRIVE PANEL V12 1 VCC 0.1uF AUX5V R586 3.3K VPANEL R573 1 2 3 4 5 C516 100uF_16V_T DBO4 C510 0.1uF DGND V12 L527 FB N818 LM1117-3.3V C560 0.1uF AUX5V OPTIONAL FOR 12V DRIVE PANEL 0 A A V3.3 is the 3.3V power supply for PW113 Title DISPLAY.SCH Size Number Revision Orcad B Date: 1 2 C 10uF/10V 0.1uF DBO2 HEADER 16X2 C530 0.1uF DGND BC847(SOT-23) C561 VCC L503 FB V33PANEL Q503 10K DGO4 1 2 3 4 5 6 C823 C520 9435A DGO0 L816 FB 3 Vo XS514 D2006-6A 4 DCLK DHS R578 C513 ADJ DVS 0 R573 ҂ᑺ Vin C ON/OFF 1K R582 Vo2Vo4 L828 FB R584 3 DBE[0..7] BRIGHT 10K C562 0.1uF 10K 2 DGE[0..7] R582 2 V33PENAL Q504 BC847(SOT-23) TO INVERTER R580 TO INVERTER DGO[0..7] 3 4 5 1-Aug-2003 Sheet of 6 KLC-TM1508 Analog Board schematic circuit diagram 1 2 3 4 5 6 7 8 KLC-TM1508 inverter•PCB P/N•35007175• schematic circuit D D R720 300k VL REF R721 56k XS702 28 V701A 2 3 Comp LLG FT DrvL 1 2 27 2 26 C710 SI9926BDY R709 1K 22nF 25 V701B 5 IS ULG 24 4 C R726 0ohm 10nF 8 9 R707 30k IL 10 11 C722 4.7nF C730 4.7nF C Byp PRL NC PGR 2 D702 1N4148 21 ABrt LRG NC DrvR 20 R713 2K C720 0.1uF C728 N/A C712 IL OutR 12 XS701 R706 BOsc URG SI9926BDY 1 1 DBrt BtR R708 20k 4 T702 14 En PRR 4 3 IL 11 SI9926BDY 8 5 C715 1uF/25v EPC-19 XS704 1 2 C723 22pF/3kV C717470pF R715 51K 22nF C708 1uF IL 15 D701 1N4148 N701 MP1018EM R710 300K R712 2K C719 0.1uF C729 N/A D704 1N4148 XS705 C724 4.7nF C731 4.7nF B 1 2 IS V703 MMBT3904 R731 24k T704 200mH R728 3.3k 17 10k 4 2 2 16 3 200mH C737 1uF/25V 18 C713 13 T703 VL C733 1uF/25V 2 19 R711 300K R717 1k V702B R729 75ohm C725 0.1uF C718 470pF 22nF R703 68ohm B EPC-19 SI9926BDY V702A R730 300k 5 22 N/A 6 5 4 3 2 1 8 C714 1uF/25v 1 2 22nF 7 C703 R727 D703 1N4148 REF R705 300k C736 1uF/25V XS703 11 IS C702 10nF BtL T701 1 C704 1uF AGnd C711 2 7.8 C727 0.22uF R716 10K 23 R714 51K 3 C701 2.2nF 6 3 OutL 5.6 R701 100k VL C721 22pF/3kV C716 1uF/25V 5.6 IS 4 REF PGL 1 C709 0.47uF Ref 7.8 1 R702 D705 10k 1N4148 IL C707 0.1uF IS R704 100k F701 C735 0.1uF/16V R718 100K C734 0.1uF/16V R719 100K 4A + C705 220uF/25V A A Title INV-MP1018 Size Number A3 Date: 1 2 3 4 5 6 Revision A 1 9-Oct-2004 7 Sheet 1 of 1 Drawn By: 8 KLC-TM1508 Digital Board Top layer KLC-TM1508 Digital Board Bottom layer KLC-TM1508 Analog Board Toplayer KLC-TM1508 Analog Board Bottomlayer KLC-TM1508 inverter•P/N•34002054• Emax CUSTOMER: Specification LCD PANEL DC TO AC INVERTER 1 PLCD0317403 REV:0 10MAX 52.0 2.0MAX £X 4.0*2 184 5.0 52.0 92.0 6.0 1.6 Tolerance: ¡Ó0.15mm 3 APR. / 24 / 2003 DIMENSION MEASURE:(UNIT:mm) 25 of Emax CUSTOMER: Specification 2 LCD PANEL DC TO AC INVERTER LOAD 100 £[ VT LOAD TEST CIRCUIT: 100£[ 3 APR. / 24 / 2003 PLCD0317403 REV:0 VT of VT 100 £[ LOAD VT 100 £[ LOAD Emax CUSTOMER: Specification LCD PANEL DC TO AC INVERTER PLCD0317403 REV:0 LAYOUT DRAWING: 3 of 3 APR. / 24 / 2003 Emax CUSTOMER:____________________________________ Specification Part Name: LCD PANEL DC TO AC INVERTER Page: 1 of 2 Model No: PLCD0317403 Date: APR. 24 2003 MAKER 22uF/16V(FP1451 or TL1451 or 2.2uF/50V(BA9741 or AT1741S) UL No. 1 TEAPO,SANYO,HER MEI,FUHJYYU C5,C9,C14,C15,C1 6,C17,C18,C21,C25 104/50V,0603 ,C32,C33,C35,C37 13 TDK,PHILIPS C3,C4 2 C20 154/250V C6,C10,C27,C28 C34,C36 C8 C19,C26 C1,C2,C29,C30 105/16V,0603 102/50V,0603 470/50V,0603 150uF/25V 22pF/3KV,DIP 2001J-06-RT(ORICH) CN1 S6B-PH-KL(JST) JH2-22-0648 SM02B-BHSS-1-TB(JST) CN2,CN3,CN4,CN 87210-0208(ACES) 5 W01-01100-0228 D12,D13,D14,D15, RLS4148 D16,D17,D18,D19 D9,D11 SK24 or 2A/40V D7,D8 ZENER 13V 1% 4 2 1 2 4 ARCOTRONICS,TAI YANG(7Q)(7C) TDK,PHILIPS TDK,PHILIPS TDK,PHILIPS SANYO,HER MEI,TEAPO TDK,PHILIPS 1 ORICH,JST,FCN 4 JST,ACES,FCN 4 ROHM,YING,TS,MMC 2 2 ROHM,YING,TS,MMC ROHM,YING,TS,MMC YAGEO,SYNTON-TECH, LIKET,EVER OHMS,TA-I YAGEO,SYNTON-TECH, LIKET,EVER OHMS,TA-I YAGEO,SYNTON-TECH, LIKET,EVER OHMS,TA-I YAGEO,SYNTON-TECH, LIKET,EVER OHMS,TA-I YAGEO,SYNTON-TECH, LIKET,EVER OHMS,TA-I YAGEO,SYNTON-TECH, LIKET,EVER OHMS,TA-I YAGEO,SYNTON-TECH, LIKET,EVER OHMS,TA-I YAGEO,SYNTON-TECH, LIKET,EVER OHMS,TA-I YAGEO,SYNTON-TECH, LIKET,EVER OHMS,TA-I YAGEO,SYNTON-TECH, LIKET,EVER OHMS,TA-I YAGEO,SYNTON-TECH, LIKET,EVER OHMS,TA-I R1,R2 1K ,1206, R6 100K ,0603 1 R28,R29 75K ,0603 2 R3 3.6K ,0603 1 R11,R12 11K ,0603, R19,R21 510 ,0603 2 R16,R17,R18,R20 20K ,0603 4 R34,R35 560 2 R13,R45 1.5K ,0603, 1% ,1206 1% 2 2 2 R4,R30,R31,R51,R 1M ,0603 52,R55,R56 7 56K ,0805 1 R5 Approved Cheched E201214 E60389 E41871 E60389 E205655 E201214 Design Draw Emax CUSTOMER:____________________________________ Specification Part Name: Model No: LCD PANEL DC TO AC INVERTER PLCD0317403 Page: 2 of 2 Date: APR 24 2003 MAKER R32,R33 1.2K ,0805 2 R41,R42 5.1K ,0603, 1% 2 R25,R27 30K ,0603 2 R54,R58 47K ,0603 2 R40,R46 36K ,0603, R53,R57 5.1M ,0603 2 R14 10K ,0603(FP1451 or TL1451)or 13K ,0603(BA9741 or AT1741S) 1 R47,R48,R49,R50 910 ,1206 4 Q1,Q2,Q15,Q16 Q3,Q4,Q5,Q6 SST2222A 2SC4672 NDS9435A or AO4403 or SDM9435A or AP9435M SST2907A RK7002 EDI0005 ELF0002 429003(Littelfuse) 3216FF-3A(Bussmann) 1206FA3A(SkyGate) KE32(Daito) BA100-3A(SAVE) BA9741 or FP1451 or TL1451 or AT1741S 4 4 Q7,Q8 Q9,Q10,Q11 Q12 L1,L2 L3,L4 F1 U1 1% 2 2 3 1 2 2 1 1 PCB CPC1151R6176 PLCD1717408 1 PT1,PT2 EST0015,EPC-19 2 MYLAR MLTG184*104*0.188mT 1 EVA EVA 10*13*2mm 2 UL No. YAGEO,SYNTON-TECH, LIKET,EVER OHMS,TA-1 YAGEO,SYNTON-TECH, LIKET,EVER OHMS,TA-1 YAGEO,SYNTON-TECH, LIKET,EVER OHMS,TA-1 YAGEO,SYNTON-TECH, LIKET,EVER OHMS,TA-1 YAGEO,SYNTON-TECH, LIKET,EVER OHMS,TA-1 YAGEO,SYNTON-TECH, LIKET,EVER OHMS,TA-1 YAGEO,SYNTON-TECH, LIKET,EVER OHMS,TA-1 YAGEO,SYNTON-TECH, LIKET,EVER OHMS,TA-1 ROHM,AUK ROHM,AUK CET,AO,SMC,Advanced Power. ROHM,AUK ROHM,AUK EMAX EMAX E10480 E19180(N) LITTEL,BUSSMANN, E195833 SKY GATE, Daito,SAVE E59783 E146895 ROHM,FEELING,TI,AIMT RON E112804(S) E177794 CHIAN YOU,HANT GIST, E168218(S) YUMMON,TONG JIANG, E201363 CENTURY,WAN ZHENG E189010(M) E211670 ,EISO, TUNG TA E162061(S) E162886 EMAX E110983(M) GARWARE,TORAY E86511(M) Approved GARWARE,TORAY Cheched Design Draw 2 3 4 5 6 KLC-TM1508 P/N•34002054 PLCD0317403 2 R36 30R R6 100K R32 1.2K R30 1M R47 910R D9 SK24 C25 Q9 SST2907A R43 NC R23 NC 2 CN3 SM02B-BHSS-1-TB 12 1N4148 R511M 3 C35 C34 D16 R52 1M L3 ELF0002 C 102/50V R41 5.1K R13 1.5K Q8 NDS9435A 1 R33 1.2K R1 1.0K D12 1N4148 D13 1N4148 8 R31 1M NC R9 D11 SK24 PT2 Q5 2SC4672 EST0015 2 C4 154/250V R49 910R CN4 SM02B-BHSS-1-TB 1 2 3 1 2 C30 22P/3KV CN5 SM02B-BHSS-1-TB NC R50 R27 Q11 SST2907A C2 22P/3KV 8 4 5 R10 R34 560R R11 11K L2 EDI0005 Q2 SST2222A C18 104/50V C5 104/50V C6 105/16V 8 7 6 3 1N4148 C27 C26 150uF/25V R40 36K 5.1M 104/50V 14 R14 C15 10K C8 104/50V C14 470pF/50V 104/50V R19 510R C12 NC D17 1 11 (2)IN+ GND (1)OUT (2)DTC 10 (1)IN+ (1)DTC (2)OUT 9 VCC (1)RT (1)CT C7 NC R46 36K B R54 47K 105/16V 2 C20 22uF/16V 1 R53 Q15 SST2222A R28 75K 4 R18 20K + 1 R16 20K SCP U1 FP1451 (2)FB REF 15 (1)FB 16 C16 104/50V 5 NC C C32 104/50V C17 104/50V 12 13 R17 20K (2)IN- R20 20K (1)IN- NC 4 R44 C13 1 2 C29 22P/3KV D7 RLZ13V R21 510R Q4 2SC4672 R48 910R R25 30K C21 104/50V 1 2 3 4 5 R8 NC 2 3 R35 560R C3 154/250V D SM02B-BHSS-1-TB 8 2SC4672 R7 NC Q1 SST2222A Q12 RK7002 1 R4 1M R22 NC Q10 SST2907A R5 56K R3 3.6K 2 1 W20R-6PIN-90 CN2 C1 PT1 EST0015 22P/3KV Q3 4 150uF/25V + C19 EDI0005 2 1 2 3 4 5 6 D 1 Q7 NDS9435A 8 4 1 8 L1 F1 3.0A/125V CN1 7 3 1 Q6 2SC4672 910R 1 B 12 30K D8 R29 75K C11 NC R58 47K 2 3 C37 104/50V R42 D19 1N4148 R55 1M 1N4148 C36 D18 1 5.1M R56 1M 102/50V L4 ELF0002 4 R57 Q16 SST2222A 1 104/50V 2 RLZ13V 3 C33 5.1K C28 105/16V A PLCD0317403 2 R2 1.0K D14 1N4148 D15 1N4148 Title Size Number Revision A3 Date: 1 R12 C9 11K 104/50V R45 C10 1.5K 105/16V 3 4 5 6 29-Apr-2003 7 Sheet of Drawn By: 8 A 1 D613 5V L610 BA V33 V33 TP1 VS 5VT KLC-TM2018 Digital Schematic 00 TV C601 FB N 6 2 9A 01 VGA 10 YUV 11 V G A ( S O G ) NO_USED 0.1uF N629C 1 2 3 4 12 14 15 11 TV_VS T V _ V S OUT XS603 G HSI GVSI T V _ HS G BIN T V _ H S OUT X0 X1 X2 X3 1 5 2 4 5 6 5V 5V D603 B A V 99L 3 D604 B A V 99L 3 V33 TP2 HS 3 9 R602 D B15HD 8 11 13 L611 FB V33 74HC14/SO C614 G R IN G G IN 4 0 _ O H M @ 1 0 0 MHz L604 4 0 _ O H M @ 1 0 0 MHz L605 G BIN 4 0 _ O H M @ 1 0 0 MHz L606 4 0 _ O H M @ 1 0 0 MHz L607 10K R604 R605 75 75 C619 R631 10uF 20K 10uF C626 75 D608 B A V 99L 5V R609 R610 R611 220 220 3.3K 3.3K 3 3 12pF G SCL 6 G SDA 5 3 VCLK SCL SDA NC1 NC2 NC3 GND D607 B A V 99L R619 C625 XS604 F R O M X P 301 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 R620 0 TXD1 PR_Cb H D_Y H D _Y N601 P I 5 V 330 2 3 S1A S2A C621 11 10 10uF T V _ Cb T V _ Cr TV_VS T V _ HS 1 2 3 4 5 6 7 1 15 FB Cb R621 DA S1B S2B DB S1C S2C DC S1D S2D DD R623 4 10K 1K 7 12 5VB R624 9 22K IN /EN 1 V602 B C 8 47 Y R626 10K 1K R614 C610 75 12pF 4 0 _ O H M @ 1 0 0 MHz L614 V330 C622 10uF C624 L612 TV_Cr V33 5VB R627 FB R652 C628 C615 10K 0.1uF 1 0 U F / 1 6 V-5 22K Y _ 1 8 83 1 V603 B C 8 47 Cr R628 R653 R629 10K Y 20K Cb P R_CR A V / T V / S C ART 4 0 _ O H M @ 1 0 0 MHz L616 1K C623 C612 KONKA ø¼·¹·¬¿´ íëððéííë÷ RGB,H/V SYNC&EDID 10uF R617 Title 12pF CONNECTOR1X7 F R O M X P 1 002 L609 V601 B C 8 47 R625 75 Cr 5V 0.1uF 1 4 0 _ O H M @ 1 0 0 MHz L615 12pF XS606 TV_Y 5VB C613 22K R616 1 2 3 4 5 6 7 8 9 BAIN R622 R651 14 13 C 6 1 11 0 u F XS602 9 IN /EN A RXD1 PR_Cr G AIN 0.1uF R G B S E L1 AIN-L AIN_R 12 C617 1 0 U F / 1 6 V -5 C609 4 PR_Cb DD R AIN C608 1 0 U F / 1 6 V-5 10K 3 0 DC S1D S2D 7 R IN G I NB IN 5 6 C607 0.1uF DB S1C S2C 4 L608 D612 B A V 99L 8 1 2 3 R G B S E L0 DA S1B S2B TP3 TP4 TP5 FB N604 2 4 L C 21A VCC 1 15 C605 20K 20K 7 1 2 3 4 5 6 7 8 9 3 5 6 C603 1 0 U F / 1 6 V -5 R647 R650 1 10uF R608 12pF C604 R 6 0 7 10K 5V 20K C602 0.1uF N603 P I 5 V 330 2 3 S1A S2A 5V D606 BAV70 TV_Y C606 11 10 10K V330 5V R635 20K TV_Cb D611 B A V 99L R633 12pF 5V D610 B A V 99L 10uF 10K V330 GVSI 5V C620 10K 14 13 R648 R603 FB R634 R632 4 0 _ O H M @ 1 0 0 MHz L603 5V 7 4 H C 1 4 / SO R630 4 0 _ O H M @ 1 0 0 MHz L602 R GSA 74HC14/SO L613 VEE G HSI R GSL 12 V3.3 C627 0 . 1 uF 1 0 U F / 1 6 V -5 2 A HSYNC 5V D605 B A V 99L 3 A 10 75 10uF XS601 V33 N 6 2 9E N629F Y C618 6 1 11 7 2 12 8 3 13 9 4 14 10 5 15 V33 N629D A B 7 R GSA R GSL X 75 13 INH 10 9 INPUT SW0 INPUT SW1 5V 6 74HC14/SO 7 4 H C 1 4 / SO R601 Y0 Y1 Y2 Y3 G G IN G R IN AVSYNC N602 7 4 H C 4 0 5 2D 74HC14/SO 1 2 3 4 5 6 7 8 9 10 11 12 V33 N629B 1 N 4 1 48 75 S ize A3 D a t e: 1 D o c u m e n t N u m ber Rev A 900-0XXX-00 T h u r s d a y , S e p t e m b e r 16, 2004 S h eet 2 of 11 5 V33 R OMOEn N305 R OMWEn R O MWEn 26 28 11 12 14 47 R E S E Tn R361 V33 FW Pn 10K A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 R364 0 D 4 V33 25 24 23 22 21 20 19 18 8 7 6 5 4 3 2 1 48 17 16 15 CE OE WE RP WP BYTE VPP VCC 13 FVPP 3 R362 10K R363 0 37 29 31 33 35 38 40 42 44 30 32 34 36 39 41 43 45 D1 D2 A0 D3 A1 D4 A2 D5 A3 D6 A4 D7 A5 D8 A6 D9 A7 D10 A8 D11 A9 D12 A10 D13 A11 D14 A12 D15 A13 D16 A14 A15 46 A16 GND1 27 A17 GND2 A18 A19 A M 2 9 L V 8 0 0 BT-90EC F l a s h _ 8 M TSOP48 2 1 V33 D [ 1 5 : 0] D[15:0] D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 V33 N306 2 4 C 16 6 5 SCL S DA 1 2 3 SCL SDA VCC NC0 NC1 NC2 WP GND D 8 7 C367 0.1uF V33 4 2 NVRAM SW301 SW NMI Pushbutton 1 J P 3 02 H D R _ 2 X2 J P 3 03 HDR_2X2 F CEn ICEn 1 3 V33 R OMWEn 2 4 1 3 NMI R314 10K C360 0.1uF 2 4 R315 10K V33 C R316 3.3K C 2 SW302 SW R E S E Tn Rese t Pushbutton 1 C361 18pF A [ 1 9 :1] V33 V33 V33 XS304 A2 A4 A6 A9 A11 A12 A14 A17 A19 ROMOEn D15 D14 B D5 D4 D3 D2 D9 D8 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 A1 A3 A5 A7 A8 A10 I R P n R 3 1 7 3.3K ICEn R 3 1 8 3.3K IA20 IA21 V33 V33 C363 0.1uF A13 A15 A16 A18 C390 R 3 1 9 10K 100UF TCK R 3 2 0 10K TMS R 3 2 3 10K TDI R 3 2 1 3.3K R 3 2 2 3.3K R OMWEn D7 D6 D13 D12 B D11 D10 D1 D0 H D R _ 3 0 X2 A A KONKA ø¼·¹·¬¿´ íëððéííë÷ Mermory,Promice,NMI,Reset Title S ize A3 D a t e: 5 4 3 2 D o c u m e n t N u m ber Rev A 900-0XXX-00 T h u r s d a y , S e p t e m b e r 1 6, 2004 S h eet 1 3 of 11 5 4 PV1 3 2 R425 R424 0 V33 R426 3.3K C412 3.9nF D G FILT C414 R AIN C415 G AIN C416 47nF 47nF 1nF C417 BAIN 47nF 23 I RED 37 I GREEN 43 I SOG 44 IBLUE 50 64 A HSYNC 65 FILTER 5 BLUE R432 SDA SCL STB PORTA3 A V / TV1 I R RCVR A V / TV0 P W MOUT VS HS C411 0 .1UF RTERM 208 207 206 205 204 203 202 201 100 RXD TXD PORTA0 PORTA1 PORTA2 PORTA3 PORTA4 PORTA5 PORTA6 PORTA7 N407C P W 1 306 M i sc D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 R 4 2 1 1K 142 141 140 139 138 TCK TMS T DI NMI 72 RESETB SOG N407A G r a p h i cs and V i d e o Port 55 53 54 R XD TXD GREEN PW1306 P W 1 3 0 6 _56 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 TESTEN RED 430 NC 63 62 61 60 59 58 57 56 132 R E S E Tn R433 L C DON BKLON 137 TP13 TP12 TP10 TP11 A VSYNC C R423 T E S TEN C413 39nF NMI 194 169 170 V656_0 V656_1 V656_2 V656_3 V656_4 V656_5 V656_6 V656_7 R431 1.5M TRST TCK TMS TDI TDO NMI XI XO RD WR ROMOE ROMWE CS0 CS1 Z401 X T A L 1 4 .31818 X607 X608 C418 33pF VPEN C419 33pF 193 192 191 190 189 188 183 182 181 180 179 178 177 176 175 164 163 162 161 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 160 159 158 157 156 155 154 153 152 151 150 149 148 145 144 143 D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 DCLKNEG DCLK DEN DHS DVS A [ 1 9 : 1] DR0 DR1 DR2 DR3 DR4 DR5 DR6 DR7 D [ 1 5 : 0] 196 195 197 198 199 200 W RN N 4 0 7B P W 1 3 06 D i s p l a y Port RDn TP15 WRn R OMOEn R O MWEn CS0n CS1n PW1306 V18 V18 V18 V18 V18 C422 C423 C424 C425 C426 C427 0 . 1 uF 0.1uF 0.1uF 0.1uF 0.1uF 0 . 1 uF 3.3VADC C420 0 . 1 uF C421 0 . 1 uF L408 L412 L409 FB FB FB S l e e p M o de 35ma V18A DGB0 DGB1 DGB2 DGB3 DGB4 DGB5 DGB6 DGB7 4 0 m a max. L410 FB L411 FB PV1 DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 DGG0 DGG1 DGG2 DGG3 DGG4 DGG5 DGG6 DGG7 VCLK 1 7 5 m a max. DG0 DG1 DG2 DG3 DG4 DG5 DG6 DG7 DGR0 DGR1 DGR2 DGR3 DGR4 DGR5 DGR6 DGR7 V18 V18 100_NC P VDD 107 106 103 102 101 1 2 3 4 98 97 94 93 92 91 90 89 1 2 3 4 1 2 3 4 88 87 86 85 82 81 80 79 1 2 3 4 1 2 3 4 78 77 74 73 71 70 67 66 1 2 3 4 1 2 3 4 131 130 129 128 127 126 125 124 1 2 3 4 1 2 3 4 121 120 119 118 117 116 115 114 1 2 3 4 1 2 3 4 113 112 111 110 109 108 100 99 1 2 3 4 1 2 3 4 TP6 TP7 TP8 TP9 D CLK D E N D H SDVS 47 NC 8 7 6 5 RN401 47_RN 8 7 6 RN402 5 47_RN 8 7 6 5 RN403 47_RN 8 7 6 RN404 5 47_RN 8 7 6 5 RN405 47_RN 8 7 6 RN406 5 47_RN 8 7 6 5 RN407 47_RN 8 7 6 RN408 5 47_RN 8 7 6 5 RN409 47_RN 8 7 6 RN410 5 47_RN 8 7 6 5 RN411 47_RN 8 7 6 5 RN412 8 47_RN 7 6 RN413 5 47_RN 1 C448 0.1uF D CLKn D CLK DEN DHS D VS D D D D D D D D RE0 RE1 RE2 RE3 RE4 RE5 RE6 RE7 D D D D D D D D GE0 GE1 GE2 GE3 GE4 GE5 GE6 GE7 DBE0 DBE1 DBE2 DBE3 DBE4 DBE5 DBE6 DBE7 DR DR DR DR DR DR DR DR O0 O1 O2 O3 O4 O5 O6 O7 DG DG DG DG DG DG DG DG O0 O1 O2 O3 O4 O5 O6 O7 D D D D D D D D BO0 BO1 BO2 BO3 BO4 BO5 BO6 BO7 DRE[7:0] D DGE[7:0] D B E [ 7 : 0] D RO[7:0] C D GO[7:0] DBO[7:0] V33 S l e e p M o d e 9ma max. P Q F P208 3 . 3 V A DC 3 . 3 V A D C 3 . 3 V A DC 3 . 3 V A DC 3 . 3 V A D C B V33 3 . 3 V A DC C428 C429 C430 C431 C432 C433 0 . 1 uF 0.1uF 0.1uF 0.1uF 0.1uF 0 . 1 uF V33 V33 V33 V33 V33 3 5 0 m a max. 9 0 m a max. LV1 C434 C435 C436 C437 C438 0 . 1 uF 0.1uF 0.1uF 0.1uF 0.1uF B V33 C439 C440 C441 C442 C443 C444 C445 0.1uF 0 . 1 uF 0.1uF 0.1uF 0.1uF 0.1uF 0 . 1 uF N 407DPW1306 P o w e r and Ground 3 . 3 V A D C 3 . 3 V A DC C446 C447 0.1uF 0 . 1 uF A A KONKA ø¼·¹·¬¿´ íëððéííë÷ PW1306 Title S ize A3 D a t e: 5 4 3 2 D o c u m e n t N u m ber Rev A 900-0XXX-00 T h u r s d a y , S e p t e m b e r 16, 2004 S h eet 1 4 of 11 5 4 3 5V 2 1 R Dn V33 CS0n V33 V+ VV33 V33 C H+ V33 C HV33 M E NU V33 A V /TV V33 V33 V33 D614 B A V 99L D [ 1 5 : 8] C548 0.1uF C549 0 . 1 uF V33 R539 R532 10K 10K R533 10K R534 R535 R536 10K 10K 10K R537 10K R538 10K D 8 7 6 5 4 3 2 1 N508 1 19 RN501 47_RN XS611 V+ VC H+ C HMENU A V /TV GND STANDBY 1 2 3 4 8 7 6 5 1 2 3 4 8 7 6 5 OE1 OE2 2 3 4 5 6 7 8 9 XS605 20 VCC D15 D14 D13 D12 D11 D10 D9 D8 18 17 16 15 14 13 12 11 O0 O1 O2 O3 O4 O5 O6 O7 I0 I1 I2 I3 I4 I5 I6 I7 N509 3 4 7 8 13 14 17 18 D8 D9 D10 D11 D12 D13 D14 D15 1D 2D 3D 4D 5D 6D 7D 8D 1Q 2Q 3Q 4Q 5Q 6Q 7Q 8Q 2 5 6 9 12 15 16 19 R G B S E L0 R G B S E L1 CLK CLR GND RXD 10uF 5V 1 2 3 4 F R O M X P1001 7 4 L V 273A 5V N801 C855 10nF 1 2 3 V12 4 L814 N802 FB 1 2 3 4 1 2 3 4 C851 GND C854 4 7 0 u F / 16V C864 0.1uF S1 S2 S3 G2 +12V D1a D1b D2a D2b 5 6 7 8 C865 0.22uF IN EN SW L813 COMP GND FB XS301 390K 8 C850 180pF 5 MUTE OUT G ND R843 30K R842 10K 15uH 1 2 3 4 5 6 7 8 9 10 11 12 SDA SCL 6 AIN_L AIN_R 5V L801 D810 R841 1K R878 2.2K L C DCON L816 FB FB R868 10K FB V18A GND V18 GND 5VT XS817 1 P O WER ON 1 2 3 4 R867 10K R660 S Y N COU T V862 BC847 GND 1 2 3 4 Y _ 1 8 83 C667 N606 1K 0 . 1 u F / 16V V5 C853 C662 SYNCOUT VDD CVBSIN HSYNCOUT VSYNCOUT RSET GND BPOUT 0 . 1 uF 4 7 0 u F /16V 8 7 6 5 R663 R 6 6 8 56K 5V G ND C653 C659 1 0.1uF V662 B C 8 47 C877 R664 33 C874 R679 R661 680K R662 680K GND C868 0 . 1 uF 4 7 u F / 1 6V 0.1uF 0.1uF 10K 0.1uF 5VT N O T E : R S E T must be at 1% r e s i stor. 1 V33 V605 1 R678 +12V 5V 5V D617 V606 BC847 C869 C863 0 . 1 u F 4 7 u F / 16V T V _ V S OUT C661 10K B N810 L M 1 1 1 7 MPX-3.3V N811 L M 1 1 1 7 MPX-3.3V 5V 5V C872 R845 4.7K BC847 0.1uF B Z V 5 5 - B /3V0 C875 8 A V / T V / S C ART C678 R643 C862 3 . 3 V A DC GND R675 430 GND 1K I RRCVR 510 5V 5V R666 4 7 0 u F / 16V R674 B 10uF 10K 10K V5 SYNC SEL C879 TV_HSOUT 5VT STANDBYn C859 0.22uF N813 L M 1 1 1 7 MPX-1.8V N812 L M 1 1 1 7 MPX-1.8V 33 R665 E L 1 883 R669 C F R O M X P 3 002 GND L817 1K R E S E Tn C858 3 . 3 nF 7 M P 1 410 GND C867 0.1uF 9435 0.22uF NC C866 4 7 0 u F / 16V R839 BS F M 5 8 20 V12 C880 10 +12V XS615 T o I R B oard S T A NDBY 1 + 5V 2 I R R CVR 3 G ND 4 R e d LED 5 G r e e n LED 6 L815 FB TXD1 RXD1 MUTE OUT P O W E RDOWN C R645 100 INPUT SW0 INPUT SW1 D +12V 1 2 3 4 Output Latch S T A N D B Yn XS816 TXD XS802 11 1 CS1n R E S E Tn 7 4 L V C 5 4 1 A _PW Input Buffer 5 A _ 1 206 F801 R644 100 10 GND RN502 47_RN T o K e y Board D615 B A V 99L 3 3 N 8 0 4A 0.1uF 3 + V5 1 0.22uF C870 4 7 u F / 1 6V C875 C876 0.1uF 0.1uF C860 C861 0.1uF 4 7 u F / 16V A V / TV1 2 - N803 C878 D616 10uF 1 2 3 4 C677 4 7 u F / 1 6V R649 STZ5.1 10K VDD VSS GP5 GP0 GP4 GP1 GP3 COUT 8 7 6 5 R846 P O WER ON S Y N C SEL S Y N COU T 4 L M 3 5 8 _ SO8 8 N 8 0 4B 1.5K P I C 1 2 F 629 5 + A I R RCVR 100 4 R642 100 P O W E RDOWN 100 7 6 - R654 A A V / TV0 L M 3 5 8 _ SO8 KONKA ø¼·¹·¬¿´ íëððéííë÷ Keypad input,3.3V&1.8V Reg R847 1K V607 1 R646 STANDBYn 100 Title R655 P W 1 3 0 6 _ 56 S ize A3 BC847 D a t e: 5 4 3 2 D o c u m e n t N u m ber Rev A 900-0XXX-00 T u e s d a y , O c t o b e r 2 6 , 2004 5 S h eet 1 of 11 V33 5 V O OV N N 4 3 2 1 V P A N EL 31 D CLK DRE[7:0] D RE0 D RE1 D RE2 D RE3 D RE4 D RE5 D RE6 D RE7 D GE0 D GE1 D GE2 D GE3 D GE4 D GE5 D GE6 D GE7 DBE0 DBE1 DBE2 DBE3 DBE4 DBE5 DBE6 DBE7 D DGE[7:0] D B E [ 7 : 0] D HS DVS D EN V33 R542 0 R543 0 NC 51 52 54 55 56 3 50 2 4 6 7 11 12 14 8 10 15 19 20 22 23 24 16 18 27 28 30 25 17 32 CLKIN TXIN0 TXIN1 TXIN2 TXIN3 TXIN4 TXIN6 TXIN27 TXIN5 TXIN7 TXIN8 TXIN9 TXIN12 TXIN13 TXIN14 TXIN10 TXIN11 TXIN15 TXIN18 TXIN19 TXIN20 TXIN21 TXIN22 TXIN16 TXIN17 TXIN24 TXIN25 TXIN26 TXIN23 L514 X S 5 0 6 NC C573 1 0 0 U F / 1 6 V - 5 NC TXOUT0 TXOUT0 N 516 NC D S 9 0 C 3 8 5 A MTD TXOUT1 TXOUT1 TXOUT2 TXOUT2 TXOUT3 TXOUT3 TXCOUT TXCOUT 47 48 TXE0p TXE0m 45 46 TXE1p TXE1m 41 42 TXE2p TXE2m 37 38 TXE3p TXE3m 39 40 T X E CKp T X E C Km 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 C574 0.1uF NC TXE3P TXECP TXE2P TXE1P TXE0P TXO3P T X OCP TXO2P TXO1P TXO0P 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 D TXE3M TXECM TXE2M TXE1M TXE0M TXO3P T X OCP TXO2P TXO1P TXO0P c o n n e c t o r16X2 D CLK R_F PWRDN V33 C559 100pF NC R545 220 NC V OO V33 L513 V NN V33 F B NC L515 F B NC P W DN C C R546 220 NC R544 100 NC L C D ON D S 9 0 C 3 8 3 A M T D 5 6SSOP Package D CLK D RO[7:0] D GO[7:0] B DBO[7:0] V33 F B NC D HS DVS D EN V33 31 D R O0 D R O1 D R O2 D R O3 D R O4 D R O5 D R O6 D R O7 D G O0 D G O1 D G O2 D G O3 D G O4 D G O5 D G O6 D G O7 D BO0 D BO1 D BO2 D BO3 D BO4 D BO5 D BO6 D BO7 R547 0 NC R548 0 NC 51 52 54 55 56 3 50 2 4 6 7 11 12 14 8 10 15 19 20 22 23 24 16 18 27 28 30 25 17 32 C552 C553 C555 C556 C557 C558 1 0uF NC 0.1uF NC 0.1uF NC 10uF NC 0.1uF NC 0 .1uF NC V O OV N N CLKIN TXIN0 TXIN1 TXIN2 TXIN3 TXIN4 TXIN6 TXIN27 TXIN5 TXIN7 TXIN8 TXIN9 TXIN12 TXIN13 TXIN14 TXIN10 TXIN11 TXIN15 TXIN18 TXIN19 TXIN20 TXIN21 TXIN22 TXIN16 TXIN17 TXIN24 TXIN25 TXIN26 TXIN23 V33 TXOUT0 TXOUT0 N 517 NC D S 9 0 C 3 8 5 A MTD TXOUT1 TXOUT1 TXOUT2 TXOUT2 TXOUT3 TXOUT3 TXCOUT TXCOUT 47 48 T X O0p T X O0m 45 46 T X O1p T X O1m 41 42 T X O2p T X O2m 37 38 T X O3p T X O3m 39 40 T X O C Kp TXOCKm C576 C577 C578 C579 0.1uF NC 0.1uF NC 0.1uF NC 0.1uF NC C580 C581 0 . 1 u F N C0 . 1 u F N C C575 C572 0.1uF NC 0.1uF NC B R_F PWRDN P W DN A A KONKA ø¼·¹·¬¿´ íëððéííë÷ LVDS Transmitters Title S ize A3 D a t e: 5 4 3 2 D o c u m e n t N u m ber Rev A 900-0XXX-00 T h u r s d a y , S e p t e m b e r 16, 2004 S h eet 1 6 of 11 5 4 3 2 1 DRE[7:0] DGE[7:0] D B E [ 7 : 0] Display Output V P E NAL N503 L502 FB +12V XS504 D 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 D RE7 D RE5 D RE3 D RE1 D GE7 D GE5 D GE3 D GE1 DBE7 DBE5 DBE3 DBE1 D CLK D VS 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 R553 5V D RE6 D RE4 D RE2 D RE0 D GE6 D GE4 D GE2 D GE0 DBE6 DBE4 DBE2 DBE0 R552 L505 1 2 3 4 0 NC F B NC C551 0.1uF R554 C582 10K 0.1uF 8 7 6 5 C586 R566 C588 0 D 1 0 0 u F _ 1 6V_T 0.1uF F O R 3 . 3 V PANEL 9435 R567 N518 B A 0 3 3FP R555 0 NC R 5 5 6 10K 1 L C DON V506 B C 8 47 D EN D HS R557 330 h e a d e r18X2 C561 0 . 1 uF C560 4 7 u F / 16V L 5 0 4 FB V P E NAL C589 C587 0.1uF 1 0 0 u F _ 1 6V_T D501 LED 5V DBO[7:0] C C D GO[7:0] R561 10K R 5 5 9 10K D RO[7:0] P WMOUT XS505 DR DR DR DR O1 O3 O5 O7 DG DG DG DG O1 O3 O5 O7 D D D D BO1 BO3 BO5 BO7 31 29 27 25 23 21 19 17 15 13 11 9 7 5 3 1 32 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2 DR DR DR DR O2 O4 O6 O8 DG DG DG DG O2 O4 O6 O8 D D D D R562 NC 1 V507 BC847 5V C584 0.1uF LCD C ontrol Output R564 4.7K T O I N V ERTER XS512 R560 10K 1 2 3 4 5 6 O N / OFF B r i ght BO2 BO4 BO6 BO8 R565 1K 1 BKLON R563 5.1K V509 B C 8 47 L503 FB C592 1 0 0 u F _ 16V_T +12V C590 1 0 0 u F _ 1 6V_T C591 0.1uF h e a d 16X2 B B A A KONKA ø¼·¹·¬¿´ íëððéííë÷ Output Connector T itle S ize A3 D a t e: 5 4 3 2 D o c u m e n t N u m ber Rev A 900-0XXX-00 T h u r s d a y , S e p t e m b e r 16, 2004 S h eet 7 1 of 11 1 2 3 KLC-TM2018 Analog Board Schematic 5V2-CD CVBS_OUT R1077 C1073 10uF/16V 10k CVBS_OUT L1012 100uH C1077 0.01uF 1 C1078 0.01uF 2 C1076 100uF/10V V1008 BC847 C1074 0.1uF 3 0.01uF 4 C1079 5 R1076 820 R1078 10k R1079 470 R1080 150 C1075 0.47uF/50V 0.01uF 6 C1080 7 8 9 5V2-CD 10 C1085 C1086 0.1uF 47uF/10V L1013 100uH 11 12 C1087 C1088 0.1uF 47uF/10V L1014 100uH C 13 14 BIAS VB1 6 VRT COUT VDD1 VSS1 TESTI1 YOUT VSS2 VB2 VRB PD YCIN FIL TEST VSS4 KILLER VDD4 TESTI2 FSC VDD3 TESTOUT VSS3 MODE1 VDD2 SDA TESTI3 SCL C1081 0.01uF 28 R1082 27 COMB_C 0 26 R1083 25 C1082 0.01uF R1081 330 C1083 680pF 24 23 22 COMB_Y D Comb_C_out Comb_Y_out 0 R1085 NC R1084 NC C1084 0.1uF 5V2-CD 21 R1089 2K 5V2-CD 20 C1089 0.01uF 19 C1090 L1015 100uF/10V 100uH R1091 12K C1092 0.01uF C1091 0.01uF 17 C1094 15pF V1009 BC847 18 V1010 BC847 R1088 1K R1090 1K R1093 1.5K R1092 5.6K L2107 47uH V12A2 L1212 R1094 27uH 510 C1093 10pF C1095 33pF FSC_OUT FSC_OUT 16 15 VSS +12V 5 N1004 TC90A69F 5V2-CD D 4 R1086 100 SDA R1087 100 SCL C SDA SCL 1 2 VSS R XS2003 L XS2002 CON2 + C2101 100uF/16V C2100 0.1uF N2001 TDA1517A AUL_IN1 DACM_L DACM_R R2093 1.5K VOL_L1 C2098 0.1uF 1.5K VOL_R1 C2099 0.1uF GND 18 SGND GND 17 3 SVRR GND 16 4 OUT1 GND 15 5 PGND GND 14 6 OUT2 GND 13 CON2 470uF/16V C2102 OUT_L C2104 B DACM_R C1096 3300p C1097 470uF/16V C2103 OUT_R R2095 R2096 10K 10K 3300p V12A2 C2106 470uF/16V R2097 10K + STB VP GND 12 8 M/STB GND 11 AUR_IN 9 IN2 GND 10 XS2001 XP2004 CON5 CON5 R2090 R2091 1K 1K C2093 0.22U V12A2 R2098 0 V2011 BC847 V2010 BC847 mute C2094 0.22U D2002 1N4148 V2012 BC847 R2084 R2085 R2086 10K 10K 10K R2087 10K R2089 V12A2 10K + C2015 470uF/16V pixelworks V2013 BC857 TM see the future Title: R2088 File: COMB FILTER.sch 10K 2 B XS2006 EARPHONE R2099 10K A 1 1 2 3 4 5 R2083 10K R2100 10K R2080 10K 7 MUTEn + 100uF/16V 1 2 3 4 5 + R2094 IN1 2 + DACM_L 1 2 3 Eng. Appr.: 4 5 A A-2205 World Trade Plaza, Futian District Phone: 86-755-83679633 Fax: 86-755-83690623 Shenzhen P.R.China, 518033 Number: Revision: Size: B Brawn: Kong Sheet 4 of 8 6 Date: 9-Mar-2005 Printed Date/Time: 16:46:05 1 2 3 4 +5V 5 6 R1105 100 1/16W R1107 R2207 20K NC 1K 1/16W SDA SDA D1101 MA858 AFC R2028 1K 1 2 3 C1818 4 0.22uF 4 3 2 1 5V1 + EN SW COMP GND FB R2215 100 12 SCL SIOMAD 11 10 SAD NC TAGC 13 REF 9 TOP VAGC 16 15 C2229 10pF 14 8 AUD RF_AGC + DGND AGND VPLL 18 19 Vp CVBS 7 6 DEEM AFD 5 4 FMPLL OP1 OP2 AFC 20 17 C2228 470n R2034 100K 5V1 R2035 12k RF_AGC Z2000 4.0MHZ C2226 10nF R2029 22K R2033 47 L2005 10uH + C2222 47uF/16V R2032 22K C2224 47uF/16V C1812 3.3nF RF_AGC 5V1 C2231 0.1uF V2003 BC847 5V1 7 C1811 180PF 6 5 B 3.3V N817 LM1117-3.3V R1870 30K MP1410ES 470uF_16V_T C1159 47uF/16V N/C IN C2230 47uF/16V R1875 10K 1% C1161 0.1uF C805 C807 0.1uF 100uF_6V_T R2036 22K R2037 220 TV_CVBS_OUT R2038 TV_CVBS_OUT 220 2.5V R1871 1.5K 700ma max. N817 LM1117-2.5V 5V2 L1825* C807 0.1uF 100uF_6V_T TO TDA1517 FM5820 3 C1810 0.22uF A A A C1809 1000uF_16V_T 1 FB D1808 2 K L1827 15uH ADJ L1802 10uH C805 Vin C1820 BS R1872 390K 8 C 4 R1007 220 NC CTRL GND OUT IN N1815 C1817 STB C1160 0.1uF R2030 22K RF_AGC C1158 + 21 AFC + VP 10nF 1 2 3 4 SIF1 SAW_SW AFC B 47uF/16V 22 4 R2031 330 4 C2227 220n 2 5 C2223 10nF L1801 10uH 2 1 R1225 33 C1016 0.1uF N1101 7805 +12V 5 N1006 TDA9886 Vo2Vo4 C1015 100uF/10V R1019 0 1 23 IF NC VIF1 V1002 C388A R1023 1.2K RF_AGC F1000 FUSE2 SIF2 2 R1021 75 V5TUNER AFC XS1001 CON4 1 C2225 1n5 L1004 10uH C1014 0.1uF Z2002 M9370D C1021 10000p R1106 IF_AMF 0 TV_SIF Vin + R1226 33 0 + C1013 100uF/16V D1102 MA858 3 100 C1020 10000p R1224 1.2K R1010 + C1008 47uF/16V 470 4 R1018 5V1 C1019 10000p L1003 1uH Vo2Vo4 SDA C1102 1500p 2 100 R1022 R1009 5.6K TV_SIF R2216 2.2K ADJ R1017 4 3 SDA SCL 4 1 SCL 24K 1/16W C1006 0.1uF IF_IN 2 5 L1008 11 10 9 VT NC +5V 8 7 NC SDA 6 NC SCL 5 4 NC 3 TAGC C 2 1 AGC 5V1 5 24 tuner 1 R1103 R1101 1K 1/16W NC N1000 2 3 V1101 BC847 1 V1102 BC847 24K 1/16W C2212 470n R2214 100 R1104 C1101 1000p SCL D Z2001 M3953M VIF2 R1102 0 SCL 3 R1100 24K 1/16W R1011 33 C2210 C2211 390p 10nF C2209 10nF R2213 5.6K L1101 1UH 3 SAW_SW D 3 5V1 C2005 10nF Title Size: TVK-1 TA - Audio Amplifier B Number: 00220021115 Date: 9-Mar-2005 Time: 16:46:05 File: Tuner.sch 1 2 3 4 Revision: Sheet 5 2of A 8 Pixelworks Shenzhen Office A2205, World Trade Plaza Shennan Road Shenzhen China M. Huang Pixelworks 6 1 2 TV_Y GND TV_Cb GND TV_Cr GND TV_VS TV_Hs GND 1 2 3 4 5 6 7 8 9 XS1005 CONNECTOR-9 4 5 6 TV_CVBS_OUT TV_CVBS_OUT TV_CVBS_OUT 3 TV_CVBS_OUT R1038 100 0.1uF C1037 TV_OUT CVBS/Y_2 FSC_OUT C1038 0.01uF SVIDEO_C3 C1039 0.1uF CVBS/Y_3 FSC_OUT D D C1062 470uF/10V TV-HS 5V2-CD + XS1006* AV2 R1055 1K TV-HS R1061 100 C1046 47uF/10V 13 SCL 14 SDA R1059 47 EXT_YIN R1056 10K C1064 0.01uF C1065 220uF/10V 15 R1058 1K XS1006* AV2 C1051 0.01uF SDA SCIL1 APC-FIL 39 40 41 CVBS/Y3-IN 42 ADDRESS 43 C2-IN 44 CVBS2/Y2-IN 45 COMB SYS 46 Fsc-OUT C3-IN 28 R1-in R1062 SDA R1063 0.1uF C1066 0.1uF C1067 0.1uF C1072 SCL 100 100 Cr Cb Y 5V3 C1060 0.1uF SCART_R C1069 0.1uF SCART_G C1070 0.1uF SCART_B 26 G1-in 25 B1-in SCART_FS RIN GIN BIN FBLIN B C1071 10uF/10V R1237 22K TV-Cr-OUT R1064 100 TV-Cr TV-Cb-OUT R1065 100 TV-Cb TV-Y-OUT R1066 100 TV-Y C1058 0.1uF V1007 BC847 TV-Cr TV-Cb TV-Y C1068 4.7uF/10V EXT_V R1071 0 EXT_V C TEXT_B R1069 0 SCL XS1006 AV1 TEXT_G C1053 47uF/10V 27 SCIR1 XS1006* AV2 TEXT_R 29 Y/C GND Sync-Vcc DEC_HS 30 Cr2-in Yvi-out 12 L1011 330uH 47 SCP 11 TEXT_FS 31 Cb2-in YS1(YCbCr2-in) + C1061 10uF/10V V1006 BC847 Hs 10 L1010 100uH 32 Y2-in Cr-out Y C1050 0.1uF 33 Y/C Vcc D-GND TEXT_FS C1054 0.1uF TEXT_R C1055 0.1uF TEXT_G C1056 0.1uF TEXT_B 5V2-CD 35 24 R1128 2.7K R1045 22K COMB C-IN/FORCED-S 8 C1045 0.1uF B2-in 23 C1098 10uF/10V 7 9 5V3 EXT_Y 0.1uF G2-in D-VDD Cb-out R1061 6.8K C1048 L1009 100uH R1053 0 36 34 COMB Y-IN Y-out 1 3 5V2-CD 5 6 DEC_VS COMB_C 5V-CD 0.1uF 22 COMB_C_OUT R1046 1K R1049 100 TV-VS TV-VS EXT_CIN C1047 Z1002 16.200MHZ C1052 10pF 37 R2-in 21 R1044 10K COMB_Y X'TAL Vs CLP-fil 2 4 R1042 75 4 38 YS2/YM(RGB2-in) Y1-in COMB_Y_OUT R1047 47 CVBS_OUT CVBS-OUT C1043 0.47uF/50V N1003 TB1274AF FIL 20 CVBS_OUT 3 19 V1005 BC847 R1052 100 SYNC-IN Cb1-in C1044 10uF/10V R1043 22K VIDEO_OUT CVBS/Y1-IN 2 R1050 470 Cr1-in L1016 100uH R1048 VIDEO_OUT 75 1 AFC-FIL C1049 2.2uF/50V 18 5V2 48 C1041 0.022uF Sync-GND 5V3 SVideo Input Port B R1040 3.9K R1051 10k + XS1004 SVIDEO 7 6 5 R1039 10k C1036 10uF/16V V1004 BC847 EXT_C C C1042 0.01uF 5V2-CD 17 XS1003 CON13 RSTn GND SDA SCL GND STB MUTE +5V GND CVBS GND AIN-L AIN-R L1208 100uH C1-IN 1 2 3 4 5 6 7 8 9 10 11 12 13 5V2 R1041 27K C1244 82pF CVBS/Y_1 YS3(RGB1-in) CONNECTOR-7 0.1uF C1040 + XS1007 16 Y GND Cb GND Cr GND AV/TV 1 2 3 4 5 6 7 R1067 R1068 R1070 470 470 470 + R1075 47 Video Input Port XS1006 AV1 R1072 75 R1073 10K EXT_VIN R1074 1K A pixelworks TM see the future XS1006 AV1 Title: AV_RIN File: Color Decoder.sch AV_LIN Eng. Appr.: 1 2 3 4 5 A A-2205 World Trade Plaza, Futian District Phone: 86-755-83679633 Fax: 86-755-83690623 Shenzhen P.R.China, 518033 Number: Revision: Size: B Brawn: Kong Sheet 3 of 8 6 Date: 9-Mar-2005 Printed Date/Time: 16:46:06 1 2 3 4 6 5 5V2-VCHIP CVBS_OUT CVBS_OUT R1108 470 V1012 BC847 C1141 0.1uF R1115 470 R1112 22K 5V2 L1019 47uH D 5V2-VCHIP 12 D C1142 0.1uF R1113 47 R1114 470 DEC_VIN 7 VideoIN C1143 NC TV-VS TV-HS SDA SCL TV-VS R1109 100 VS2 13 TV-HS R1110 100 HS2 5 SDA SCL R1117 R1118 100 SDA2 14 100 SCL2 15 R1119 10K 10 C1144 0.1uF N1008 Z86229 + C1145 47uF/10V VCC R1111 22K SerialEN VIN/INTRO RED HIN GREEN SDA BLUE 4 18 OSD_R R1116 2.2K TEXT_R 2 OSD_G R1121 2.2K TEXT_G 3 OSD_B R1122 2.2K TEXT_B 17 OSD_FB R1123 1.5K TEXT_FS BOX SMS CSYNC I2CSEL LPF C1149 10PF 8 TEXT_FS R1124 C1150 R1125 C1151 R1126 C1152 R1127 10PF 330 10PF 330 10PF 330 2.2K C 9 C1148 0.068uF R1120 6.8K 11 1 TEXT_B RREF VSSA C TEXT_G SCL C1146 0.1uF 6 TEXT_R C1147 6800p VDS RED GREEN BLUE VSYNC HSYNC PWM C1153* R1128* 0.1uF 22K 12MHz C1154* 18pF 40 C1155* 18pF 43 28 V3.3 + 9 10 11 12 XO XI P0_7 P0_6 P0_5 P0_4 P0_3 P0_2 XGND RESET P1_5 P1_4 P1_3 P1_2 P1_1 P1_0 TEST ADC0 ADC1 ADC2 ADC3 COR FRAME GNDA C1156* 10uF/16V FILT IREF 22 A GNDP 42 41 Z1004* PWM7 PWM6 PWM5 PWM4 PWM3 PWM2 PWM1 PWM0 SDA_NV SCL_NV 34 33 32 1 30 8 7 6 5 4 3 2 21 20 19 18 17 16 B V3.3 V3.3 V3.3 R1129* 10K N1010* 24LC21A R1130* 10K 7 52 51 48 47 46 45 DSCL 6 DSDA 5 V3.3 VCC VCLK NC NC NC SCL SDA GND 8 1 2 3 3 C1157* 0.1uF C1158* 0.1uF 4 2 + C1159* 47uF/16V C1160* 0.1uF A TVK-1 TA - Video Overlay Number: 00220021115 Date: 9-Mar-2005 Time: 16:46:06 File: Video Overlay.sch 3 VOUT 15 14 Size: B 2 VIN V3.3 29 27 Title 1 N1011* LT1117-3.3V 5V-VCHIP 38 25 26 CVBS0 CVBS1 GNDC B 13 23 24 35 ADJ 44 VDDP 39 N1009* SAA5264 1 37 36 SCL SDA VDDC 49 50 VDDA 31 V3.3 4 Revision: Sheet 5 7of A 8 Pixelworks Shenzhen Office A2205, World Trade Plaza Shennan Road Shenzhen China M. Huang Pixelworks 6 1 2 L2008 2.2uH 49 AVSUP CAPL_M + C2010 0.01u 50 ANA_IN1+AVSS 31 C2011 0.01u 51 ANA_IN- 30 C2012 0.01u 52 ANA_IN2+ SC1_OUT_L 53 TESTEN 54 XTAL_IN ASG1 ASG2 ASG4 AHVSUP AHVSS AGNDC VREFTOP SC1_IN_R SC1_IN_L SC2_IN_R SC2_IN_L SC3_IN_R SC3_IN_L SC4_IN_R SC4_IN_L CAPL_A MONO_IN 32 C2025 330 C2024 10u/10V + C2027 47uF/10V C2026 0.01U 29 C2023 10u/10V R2054 1K C2031 10U/16V SCOL1 SC1_OUT_R 28 C2032 10U/16V SCOR1 VREF1 27 SC2_OUT_L 26 SC2_OUT_R 25 NC 24 C + C2030 0.1uF C2007 47uF/10V C2029 0.1U N2000 C2008 C2009 0.01u 330 2.2uH L2018 47uH C2036 10uF/16V 48 C2002 C2003 C2004 C2006 100p 100p 100p 100p C2028 + 3.3uF C2035 0.1U XS2015 CON15 SCOR1 SCIR1 SCOL1 SCIL1 + 5V2-AU + 5V2-AU 0.47u + 5V5 C2000 100p R2011 47K C2001 100p R2007 R2008 R2009 R2010 47K 47K 47K 47K TV_SIF 5V-AU L2009 R2055 1K Z2003 55 BIN STATAV1 GIN C2013 12pF C2014 12pF 18.432M 56 57 XTAL_OUT TP AUD_CL_OUT 58 NC DACM_SUB 23 59 NC NC 22 C2022 10U/16V R2015 1K + RIN FBLIN R2016 1K + 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0.47u C2065 R2006 47K C C2064 + 1K 6 33 R2005 34 AV_RIN 0.47u 35 AV_LIN AV1 C2063 36 1K 5 D 37 R2004 0.47u 38 1K C2062 39 R2003 SCIR1 0.47u 40 AV2 C2061 41 1K 0.47u 42 R2002 SCIL1 C2060 43 1K 44 R2001 45 1K 46 PC_RIN D R2000 4 47 PC_LIN PC 3 CVBSO_2 Video_out B 5V2-AU R2012 1K 60 D_CTR_OUT1 DACM_L 21 61 D_CTR_OUT0 DACM_R 20 62 ADR_SEL 63 STANDBYQ C2053 64 0.1u NC VREF2 19 DACA_L 18 DACA_R 17 B MSP3420G 16 15 14 13 12 C2020 1000 C2019 1000 R2105 100 SDA 5V2-AU L2001 V2001 BC847 + C2017 47uF/10V C2215 330 R2042 10K RStn DACMR R2106 100 SCL A 11 10 9 8 7 6 5 4 3 2 1 SCL SDA I2S_CL I2S_WS I2S_DA_OUT I2S_DA_IN1 ADR_DA ADR_WS ADR_CL DVSUP DVSSI2S_DA_IN2 NC NC NC RESETQ 10U/16V C2021 DACML R2043 V2002 BC857 R2013 1K D2001 IN4148 + C2018 1u/10V C2016 0.01U 10K R2041 A 10k R2044 2.2k Title Size Number Revision B Date: File: 1 2 3 4 5 9-Mar-2005 Y:\ \ \tunner7336sch.DDB Sheet of Drawn By: 6 1 ! KLC-TM2018 POWER Board Schematic C911 400Vac/470p 1 D904 MBR20100 1 8,9 L902 8u/6A C914 16V/1000u 2 C917 50Vac/0.1u 3 BD901 T4SB80 C906 1KV/4700p + ! ! C904 400V/150u C905 400V/22n 3 6 R902 2W/47k 11,12 1 2 3 ! C915 16V/1000u D905 MBR20100 - 5 T901 L27_V12 R903 2W/100 R901 5(NTC) ! C913 50Vac/0.1u D903 BAV21 ! ! C903 400Vac/470p C920 400Vac/470p VD901 1/2W/18V R907 1/4W/470 R908 1/4W/100 D901 1N4007 A 4 C909 50V/1u 7 L901 LCL-F112 ! J904 1/2W 100K Vcc HV ! A HV 5 1 SS C901 250Vac/0.22u R909 1/4W/27 V901 SPP7N60C3 GATE 6 GND 8 C910 50V/0.47u N901 ICE3DS01G-D FB 2 ! ! IS R910 1/4W/1.5k 3 C902 400Vac/470p R906 2W/0.68 2 R905 2W/0.68 R914 1/4W/10k N902 PC817 ! 3 ! 3 F901 2A/250Vac R915 1/4W/1.5k R911 1/4W/1.5k C919 50V/1000p 1 4 ! N903 TL431 1 R912 1/4W/4.7k C918 50V/0.22u 1 2 N ! L 3 4 3 2 1 C916 16V/1000u C912 1kV/390p ! D902 BAV21 C908 50V/47u XS902 R913 1/4W/3k XS901 Title <Title> (power : 35007445) Size A4 Date: 1 Document Number <Doc> Tuesday, March 08, 2005 Rev 1 Sheet 1 of 1 2 1 KLC-TM2018 Panel Convert Board Schematic XS508 VCC VCC C592 VCC XS507 10uF DEN B B7 B5 B3 B1 G7 G5 G3 G1 R7 R5 R3 R1 DCLK DVS B7 B5 B3 B1 G7 G5 G3 G1 R7 R5 R3 R1 B6 B4 B2 B0 G6 G4 G2 G0 R6 R4 R2 R0 DCLK DVS DEN DHS H E A D ER18X2 B6 B4 B2 B0 G6 G4 G2 G0 R6 R4 R2 R0 DEN DHS DCLK R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0 DEN DCLK R7 R6 R5 R4 B R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0 H E A D E R 50X1 A A T itle <Title> (screen connect : 35007495) Size A3 D a te: 2 1 D o c u m ent N umber <Doc> M o n d a y , M ay 31, 2004 R ev <RevCode> S h eet 1 of 1 2 1 XS507 B 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 VCC R0 R1 R2 R3 R4 R5 R6 R7 G0 G1 G2 G3 G4 G5 G6 G7 B0 B1 B2 B3 B4 B5 B6 B7 DHS DVS DEN DCLK R4 R5 R6 R7 G0 G1 G2 G3 G4 G5 G6 G7 B0 B1 B2 B3 VCC B7 B5 B3 B1 G7 G5 G3 G1 R7 R5 R3 R1 DCLK DVS XS509 B7 B5 B3 B1 G7 G5 G3 G1 R7 R5 R3 R1 DCLK DVS 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 VCC B6 B4 B2 B0 G6 G4 G2 G0 R6 R4 R2 R0 DEN DHS B6 B4 B2 B0 G6 G4 G2 G0 R6 R4 R2 R0 KLC-TM2018 Panel Convert Board Schematic B DEN DHS HEADER18X2 B4 B5 B6 B7 DHS DVS DEN DCLK HEADER 45X1 A A Title <Title> (screen connect : 35008225) Size A3 Date: 2 1 Document Number <Doc> Wednesday, December 29, 2004 Rev <RevCode> Sheet 1 of 1 KLC-TM2018 Analog Board Toplayer KLC-TM2018 Analog Board Bottom layer KLC-TM2018 Digital Board Toplayer KLC-TM2018 Digital Board Bottom layer