Download Owners Manual - Viking
Transcript
22956 Highway 61 ♦ Morley, MO 63767 ♦Phone 573-262-3545 ♦ Fax 573-262-3369 Owners Manual VIKING-CIVES UNIVERSAL HITCHES September 2007 1 22956 Highway 61 ♦ Morley, MO 63767 ♦Phone 573-262-3545 ♦ Fax 573-262-3369 TABLE OF CONTENTS Description Page WARRANTY POLICY / ORDERING PARTS 3 WARRANTY REQUEST PROCEDURE 4 INTRODUCTION 5 DRAWING OF GENERAL MOUNTING PROCEDURE 6 PIN HIEGHT REQUIREMENTS 7 DRAWING OF TILT UQH HITCH ASSEMBLY (S7016) 8 PARTS BREAK DOWN OF TILT UQH HITCH ASSEMBLY (S7016) 9 DRAWING OF LO-PRO UQH HITCH ASSEMBLY (S7006) 10 PARTS BREAK DOWN OF LO-PRO UQH HITCH ASSEMBLY (S7006) 11 DRAWING OF TILT PIN TYPE HITCH ASSEMBLY (S7011) 12 PARTS BREAK DOWN OF TILT PIN TYPE HITCH ASSEMBLY (S7011) 13 DRAWING OF LO-PRO PIN TYPE HITCH ASSEMBLY (S7001) 14 PARTS BREAK DOWN OF LO-PRO PIN TYPE HITCH ASSEMBLY (S7001) 15 DRAWING OF LO-PRO FLINK HITCH ASSEMBLY (S7004) 16 PARTS BREAK DOWN OF LO-PRO FLINK HITCH ASSEMBLY (S7004) 17 DRAWING OF LO-PRO QUICK LOOP HITCH ASSEMBLY (S7003) 18 PARTS BREAK DOWN OF LO-PRO QUICK LOOP HITCH ASSEMBLY (S7003) 19 DRAWING OF UNIVERSAL TILT FLINK HITCH ASSEMBLY (S7014) 20 PARTS BREAKDOWN OF UNIVERSAL TILT FLINK HITCH ASSEMBLY (S7014) 21 DRAWING OF UNIVERSAL TILT QUICK LOOP HITCH ASSEMBLY (S7013) 22 PARTS BREAKDOWN OF UNIVERSAL TILT QUICK LOOP HITCH ASSEMBLY (S7013) 23 DRAWING OF PIN AND LOOP RECEIVER WITH OUTER LUGS 24 September 2007 2 22956 Highway 61 ♦ Morley, MO 63767 ♦Phone 573-262-3545 ♦ Fax 573-262-3369 WARRANTY POLICY Wheeler Steel and Truck Equipment, Inc. warrants products of its manufacture against defects in workmanship and material for a period of one year, from the date of shipment to the customer. In consequence of this warranty, any component part or parts of such products proving defective within the above specified time will be repaired or replaced F.O.B. factory. Providing such parts are returned, transportation prepaid, to the factory and found defective by Wheeler Steel and Truck Equipment, Inc. This warranty will not apply to any product which has been repaired or altered outside of Wheeler Steel and Truck Equipment, Inc. factory in any way, so as in Wheeler Steel and Truck Equipment, Inc.’s judgment, to affect its stability or reliability, nor which has been subject to misuse or accident. The obligations of Wheeler Steel and Truck Equipment, Inc. under this warranty are limited to the replacement of defective parts. Such obligations are exclusive and in lieu of all other remedies, warranties, guarantees of liabilities, expressed or implied, with respect to each product delivered, hereunder, arising by law or otherwise (including without limitation any obligation or liability by Wheeler Steel and Truck Equipment, Inc. arising from negligence or with respect to fitness, merchantability, loss of use, revenue, or profit, or consequential damages or injuries). This limited warranty shall not be extended, altered, or varied except by a written instrument signed by Wheeler Steel and Truck Equipment, Inc. Wheeler Steel and Truck Equipment, Inc. assumes no responsibility for engines, electrical equipment or any other equipment and accessories not manufactured by Wheeler Steel and Truck Equipment, Inc. beyond the warranty of the manufacturer of such equipment of accessories. All warranty work done on Wheeler Steel and Truck Equipment, Inc. equipment must have prior authorization from Wheeler Steel and Truck Equipment, Inc. along with a “Return Goods Authorization” number. All labor and parts issued by user for Wheeler Steel and Truck Equipment, Inc. warranty without an authorization number and a signed authorization warranty form will be at the users own cost. ORDERING PARTS Delays and errors can be eliminated when ordering instructions are followed correctly. 1. Place orders direct with Wheeler Steel and Truck Equipment, Inc. / nearest dealer. 2. State Company name, address, and postal/zip code. 3. Give the exact model and serial number of the equipment/unit (stamped on the unit identification plate.) 4. Furnish part number, description and quantities required. Print or type order clearly. 5. Give specific shipping instructions. Wheeler Steel and Truck Equipment, Inc. – 22956 Highway 61 Morley, MO 63767; (573) 262-3545; (573) 2623369 Service and Parts: Daniel Wheeler; [email protected] September 2007 3 22956 Highway 61 ♦ Morley, MO 63767 ♦Phone 573-262-3545 ♦ Fax 573-262-3369 WARRANTY REQUEST PROCEDURE All repairs considered for warranty that are performed outside of Wheeler Steel and Truck Equipment, Inc.; require prior written authorization from Wheeler Steel and Truck Equipment, Inc. Failure to obtain written warranty authorization prior to repairs may result in the rejection of the warranty claim. To obtain warranty consideration one must provide all required Wheeler Steel and Truck Equipment, Inc. with unit information including date of manufacture and serial numbers. In most cases this information is easily obtained from the “Shipped Unit Tag” (located in most cases inside the driver’s side door) and/or individual unit serial tag. (A) To obtain Parts Warranty Consideration: (1) Contact Wheeler Steel and Truck Equipment, Inc. customer service to obtain a Return Goods Authorization (RGA) number. Any product arriving at Wheeler Steel and Truck Equipment, Inc. without a RGA number will be rejected and returned to the sender at his or her own expense. (2) Goods are to be shipped prepaid to Wheeler Steel and Truck Equipment, Inc. in Morley, Missouri. All items should be clearly marked with the appropriate RGA number. (3) When a replacement item is shipped to replace a defective part for warranty consideration the following additional steps will occur: a) An invoice will be generated for the value of the replacement item(s). b) The defective part(s) must be returned (prepaid) to Wheeler Steel and Truck Equipment, Inc. c) Upon receiving the defective part(s) Wheeler Steel and Truck Equipment, Inc. will issue and process a Discrepant Material Report (DMR). Once the evaluation of the DMR report is complete and the parts are deemed warranty, a credit will be issued against the outstanding invoice. If the part(s) are deemed Non-warranty the invoice will remain outstanding to be paid to Wheeler Steel and Truck Equipment, Inc. Any part(s) to be returned to the customer will be at his or her own expense. (B) To obtain Labor Parts Repair Warranty Consideration: In the event that repairs are required outside of Wheeler Steel and Truck Equipment, Inc. facility that may be considered for warranty the following steps must occur. Notification of Wheeler Steel and Truck Equipment, Inc. customer service must take place prior to the start of any repairs. (1) Contact Wheeler Steel and Truck Equipment, Inc. customer service to obtain a Warranty Claim Form (WCF) and warranty authorization number. (2) Fill out all required WCF information and fax or mail the completed form to Wheeler Steel and Truck Equipment, Inc., attention Customer Service Department. (3) Once the WCF report has been reviewed warranty authorization will be granted or denied. NOTE: Wheeler Steel and Truck Equipment, Inc. warranty labor rates will apply unless specifically determined otherwise. Any part(s) involved in a WCF request must follow the Parts Warranty Consideration procedures. September 2007 4 22956 Highway 61 ♦ Morley, MO 63767 ♦Phone 573-262-3545 ♦ Fax 573-262-3369 INTRODUCTION This instruction/parts manual has operation and maintenance information for Wheeler Steel and Truck Equipment, Inc. Universal Hitches. It has been prepared to familiarize you with the design features of the unit, and to instruct you in its proper operation and maintenance. Read this manual carefully before you operate and/or service your MW Universal Hitches. Remember that you’re working with heavy equipment that can injure you or someone else. You can help lessen the chance of injury by following the procedures in this manual, carefully. DANGER: If incorrectly used, this equipment can cause severe injury. Your chance of injury can be greatly reduced by following all caution/warning decal notifications. All decals must be kept clean and complete. Replace any decals that are unreadable. Decals may be purchased directly from Wheeler Steel and Truck Equipment, Inc. and/or the nearest authorized dealer. All Operator/Service people should review this manual carefully and become familiar with its contents. If anyone else beside you operates or services this equipment, make sure they read this manual and are instructed to follow the safety procedures related to this equipment. September 2007 5 This Owner's Manual File is Contained Within Plow Set Up-2.idw LOCATE THE CONNECTING LUGS ON THE HITCH IN LINE WITH THE REAR CLIP ANGLES AND WELD IN PLACE. MEASURE AND CUT BRACE BARS FROM OPTIONAL BRACE ARM KIT (200122035) TO SUIT. NEXT, MARK AND DRILL A 13/16'' DIAMETER HOLE IN BRACE BAR TO MATCH CLIP ANGLE. BOLT IN PLACE WITH 3/4'' DIAMETER BOLTS. STEP 4: STEP 5: EQUIPMENT MAY NOT BE EXACTLY AS SHOWN. SOME COMPONENTS MAY BE OPTIONAL TO MAINTAIN OUR ON-GOING PRODUCT AND DEVELOPMENT IMPROVEMENT PROGRAM, VIKING-CIVES RESERVES THE RIGHT TO CHANGE EQUIPMENT & SPECIFICATION WITHOUT NOTICE. LOCATE THE REAR CLIP ANGLE BRACKETS FROM OPTIONAL BRACE ARM KIT (ITEM 200122035) IN A SUITABLE LOCATION ON THE TRUCK FRAME BEHIND THE SPRING SHACKLE. NEXT, MARK AND DRILL FOUR (4) 11/16'' DIAMETER HOLES ON EACH CLIP ANGLE. TRANSFER THE EXISTING HOLES FROM THE FRAME TO THE CLIP ANGLE WHERE POSSIBLE. BOLT IN PLACE WITH FOUR (4) 5/8'' DIAMETER BOLTS. [NOTE: THE CLIP ANGLES MUST BE SET ACCORDING TO THE FRAME AND SPRING WIDTHS, ALLOWING CLEARANCE FOR THE THRUST ARM BRACES, PRIOR TO FINAL WELDING.] STEP 3: CENTER THE HITCH ONTO THE BUMPER ANGLE WITH AN APPROXIMATE PUSH HEIGHT CENTER OF 14'' TO 15'' FROM GROUND LEVEL; WELD HITCH TO BUMPER ANGLE. STEP 2: NOTES: HITCH SHOWN IS NOT REPRESENTED FOR ALL UNIVERSAL HITCHES. CENTER OPTIONAL BUMPER ANGLE (ITEM 00122027) ONTO EXISTING FRONT BUMPER; NEXT, LOCATE AND DRILL A MINIMUM OF THREE (3) 11/16'' DIAMETER HOLES THROUGH THE BUMPER ANGLE AND EXISTING TRUCK BUMPER. BOLT THE BUMPER ANGLE IN PLACE WITH 5/8'' DIAMETER BOLTS. 14'' MIN to 15'' MAX NOTES: PUSH FRAME INSTALLED HEIGHT SHOULD ATTAIN 0~ TO 4~ RELATIVE TO GROUND FOR ALL UNIVERSAL HITCHES. STEP 1: VIKING-CIVES GROUP UNIVERSAL HITCH -GENERAL MOUNTING PROCEDURE- 22956 HIGHWAY 61 MORLEY, MO 63767 (573) 262-3545 (573) 262-3369 FAX 3° 22956 Highway 61 ♦ Morley, MO 63767 ♦Phone 573-262-3545 ♦ Fax 573-262-3369 PIN HIEGHT REQUIREMENTS A. Angular push frame plows: 14” to 16” 1. MW plows A. 36R10, 36R11, 36R12 B. 41R10, 41R11, 41R12 C. 48R10, 48R11, 48R12 2. MW One-way plows B. Tubular push frame plows: 1. One-way @ 18” to 20” 2. FE @ 18” to 20” 3. J-plow @ 20” to 22” 4. Flex plow @ 18” to 20” September 2007 7 212 NORTH EVANS ROAD, EVANSDALE, IOWA 50707 (319)236-7977 PH (319)236-7980 FX UNIVERSAL TILT UQH HITCH ASSEMBLY (S7016) 16 13 4 2 5 7 1 14 8 12 10 8 6 14 15 9 11 3 ITEM DRAWING NO. ALT. ITEM NO. 1 20303003 2 20303004 3 20303001 4 20303000 5 20427000 6 281029 7 281022A 81022 8 237278 9 281013A 81013A 10 20P054 11 3SK3410 12 20900004 13 20P148A 14 3SK3460 80536 15 280536A 80536A 16 280569A DESCRIPTION TILT UQH LOWER WELDMENT UPPER TILT WELDMENT INNER ARM WELDMENT LIFT ARM WELDMENT CYLINDER RETAINING STOP BOLT HEX 1 X 5 1/2 UNC ZINC BOLT HEX 1 X 4 1/2 UNC ZINC NUT HEX TOPLOCK 1 UNC ZINC FLATWASHER SAE 1 ZINC PIN 1" X 5 1/2" PIN 1 X 4 PIN 1.000 DIA X 3.406 PIN 1 X 3 COTTER HAIRPIN 3/16 X 3 3/4 ZINC CLINCH PIN 5/16 X 1 1/4 ZINC ROLL PIN 3/8 X 2 1/2 ZINC QTY 1 1 1 1 1 2 1 3 1 1 1 2 2 3 1 2 EQUIPMENT MAY NOT BE EXACTLY AS SHOWN. SOME COMPONENTS MAY BE OPTIONAL TO MAINTAIN OUR ON-GOING PRODUCT AND DEVELOPMENT IMPROVEMENT PROGRAM, VIKING-CIVES RESERVES THE RIGHT TO CHANGE EQUIPMENT & SPECIFICATION WITHOUT NOTICE. 8 This Owner's Manual File is Contained Within 20301000-PRESENTATION.idw 22956 Highway 61 ♦ Morley, MO 63767 ♦Phone 573-262-3545 ♦ Fax 573-262-3369 S7016: TILT UQH HITCH ASSEMBLY ITEM # PART # 1 20303003 TILT UQH LOWER WELDMENT 1 2 20303004 UPPER TILT WELDMENT 1 3 20303001 INNER ARM WELDMENT 1 4 20303000 LIFT ARM WELDMENT 1 5 20427000 CYLINDER RETAINING STOP 1 6 281029 BOLT HEX 1” X 5 ½” UNC ZINC 2 7 281022A BOLT HEX 1” X 4 ½” UNC ZINC 1 8 237278 NUT HEX 1” X 4 ½” UNC ZINC 3 9 281013A FLAT WASHER SAE 1” ZINC 1 10 20P054 PIN 1” X 4 5/8” CH 1 11 3SK3410 PIN 1” X 4” 1 12 20900004 PIN 1.000 DIA X 3.406 2 13 20P148A PIN 1” X 3” 2 14 3SK3460 COTTER HAIRPIN 3/16” X 3 ¾” ZINC 3 15 280536A CLINCH PIN 5/16” X 1 ¼” ZINC 1 16 280569A ROLL PIN 3/8” X 2 ½” ZINC 2 September 2007 DESCRIPTION 9 QTY 212 NORTH EVANS ROAD, EVANSDALE, IOWA 50707 (319)236-7977 PH (319)236-7980 FX UNIVERSAL LO-PRO UQH HITCH ASSEMBLY (S7006) 13 10 2 4 6 5 1 11 9 8 12 7 3 ITEM DRAWING NO. ALT. ITEM NO. 1 20303006 2 20303000 3 20303001 4 20427000 5 281022A 81022 6 237278 7 281013A 81013A 8 20P054 9 3SK3410 10 20P148A 11 3SK3460 80536 12 280536A 80536A 13 280569A DESCRIPTION NEW LOW-PRO UQH HITCH LIFT ARM WELDMENT INNER ARM WELDMENT CYLINDER RETAINING STOP BOLT HEX 1 X 4 1/2 UNC ZINC NUT HEX ELASTIC 1 UNC ZINC FLATWASHER SAE 1 ZINC PIN 1" X 5 1/2" PIN 1 X 4 PIN 1 X 3 COTTER HAIRPIN 3/16 X 3 3/4 ZINC CLINCH PIN 5/16 X 1 1/4 ZINC ROLL PIN 3/8 X 2 1/2 ZINC QTY 1 1 1 1 1 1 1 1 1 2 1 1 2 EQUIPMENT MAY NOT BE EXACTLY AS SHOWN. SOME COMPONENTS MAY BE OPTIONAL TO MAINTAIN OUR ON-GOING PRODUCT AND DEVELOPMENT IMPROVEMENT PROGRAM, VIKING-CIVES RESERVES THE RIGHT TO CHANGE EQUIPMENT & SPECIFICATION WITHOUT NOTICE. 10 This Owner's Manual File is Contained Within 20301001-PRESENTATION.idw 22956 Highway 61 ♦ Morley, MO 63767 ♦Phone 573-262-3545 ♦ Fax 573-262-3369 S7006: LO-PRO UQH HITCH ASSEMBLY ITEM # PART # DESCRIPTION 1 20303006 NEW LO-PRO UQH HITCH 1 2 20303000 LIFT ARM WELDMENT 1 3 20303001 INNER ARM WELDMENT 1 4 20427000 CYLINDER RETAINING STOP 1 5 281022A BOLT HEX 1” X 4 ½” UNC ZINC 1 6 237278 NUT HEX ELASTIC 1” UNC ZINC 1 7 281013A FLAT WASHER SAE 1” ZINC 1 8 20P054 PIN 1” X 4 5/8” CH 1 9 3SK3410 PIN 1” X 4” 1 10 20P148A PIN 1” X 3” 2 11 3SK3460 COTTER HAIRPIN 3/16” X 3 ¾” ZINC 1 12 280536A CLINCH PIN 5/16” X 1 ¼” ZINC 1 13 280569A ROLL PIN 3/8” X 2 ½” ZINC 2 September 2007 11 QTY 212 NORTH EVANS ROAD, EVANSDALE, IOWA 50707 (319)236-7977 PH (319)236-7980 FX UNIVERSAL TILT PIN TYPE HITCH ASSEMBLY (S7011) 17 14 3 1 5 15 13 7 8 2 9 8 16 10 6 15 12 4 11 16 ITEM DRAWING NO. ALT. ITEM NO. 1 20303004 2 20303007 3 20303000 4 20303001 5 20427000 6 281029 7 281022A 81022 8 237278 9 281013A 81013A 10 20P054 11 20P010 12 3SK3410 13 20900004 14 20P148A 15 80536 3SK3460 16 280536A 80536A 17 280569A DESCRIPTION UPPER TILT WELDMENT LOWER TILT SECTION PIN TYPE LIFT ARM WELDMENT INNER ARM WELDMENT CYLINDER RETAINING STOP BOLT HEX 1 X 5 1/2 UNC ZINC BOLT HEX 1 X 4 1/2 UNC ZINC NUT HEX ELASTIC 1 UNC ZINC FLATWASHER SAE 1 ZINC PIN 1" X 5 1/2" PIN 1 1/4 X 4 3/8 UH PIN 1 X 4 PIN 1.000 DIA X 3.406 PIN 1 X 3 COTTER HAIRPIN 3/16 X 3 3/4 ZINC CLINCH PIN 5/16 X 1 1/4 ZINC ROLL PIN 3/8 X 2 1/2 ZINC QTY 1 1 1 1 1 2 1 3 1 1 2 1 2 2 3 3 2 EQUIPMENT MAY NOT BE EXACTLY AS SHOWN. SOME COMPONENTS MAY BE OPTIONAL TO MAINTAIN OUR ON-GOING PRODUCT AND DEVELOPMENT IMPROVEMENT PROGRAM, VIKING-CIVES RESERVES THE RIGHT TO CHANGE EQUIPMENT & SPECIFICATION WITHOUT NOTICE. 12 This Owner's Manual File is Contained Within 20301002-PRESENTATION.idw 22956 Highway 61 ♦ Morley, MO 63767 ♦Phone 573-262-3545 ♦ Fax 573-262-3369 S7011: TILT PIN TYPE HITCH ASSEMBLY ITEM # PART # 1 20303004 UPPER TILT WELDMENT 1 2 20303007 LOWER TILT SECTION PIN TYPE 1 3 20303000 LIFT ARM WELDMENT 1 4 20303001 INNER ARM WELDMENT 1 5 20427000 CYLINDER RETAINING STOP 1 6 281029 BOLT HEX 1” X 5 ½” UNC ZINC 2 7 281022A BOLT HEX 1” X 4 ½” UNC ZINC 1 8 237278 NUT HEX ELASTIC 1” UNC ZINC 3 9 281013A FLAT WASHER SAE 1” ZINC 1 10 20P054 PIN 1” X 4 5/8” CH 1 11 20P010 PIN 1 ¼” X 4 3/8” UH 2 12 3SK3410 PIN 1” X 4” 1 13 20900004 PIN 1.000 DIA X 3.406 2 14 20P148A PIN 1” X 3” 2 15 3SK3460 COTTER HAIRPIN 3/16” X 3 ¾” ZINC 3 16 280536A CLINCH PIN 5/16” X 1 ¼” ZINC 3 17 280569A ROLL PIN 3/8” X 2 ½” ZINC 2 September 2007 DESCRIPTION 13 QTY 212 NORTH EVANS ROAD, EVANSDALE, IOWA 50707 (319)236-7977 PH (319)236-7980 FX UNIVERSAL LO-PRO PIN TYPE HITCH ASSEMBLY (S7001) 14 11 2 1 4 6 5 9 12 13 13 7 10 8 3 ITEM DRAWING NO. ALT. ITEM NO. 1 20303005 2 20303000 3 20303001 4 20427000 5 281022A 81022 6 237278 7 281013A 81013A 8 20P010 9 20P054 10 3SK3410 11 20P148A 12 3SK3460 80536 13 280536A 80536A 14 280569A DESCRIPTION LOW-PRO PIN TYPE WELDMENT LIFT ARM WELDMENT INNER ARM WELDMENT CYLINDER RETAINING STOP BOLT HEX 1 X 4 1/2 UNC ZINC NUT HEX ELASTIC 1 UNC ZINC FLATWASHER SAE 1 ZINC PIN 1 1/4 X 4 3/8 UH PIN 1" X 5 1/2" PIN 1 X 4 PIN 1 X 3 COTTER HAIRPIN 3/16 X 3 3/4 ZINC CLINCH PIN 5/16 X 1 1/4 ZINC ROLL PIN 3/8 X 2 1/2 ZINC QTY 1 1 1 1 1 1 1 2 1 1 2 1 3 2 EQUIPMENT MAY NOT BE EXACTLY AS SHOWN. SOME COMPONENTS MAY BE OPTIONAL TO MAINTAIN OUR ON-GOING PRODUCT AND DEVELOPMENT IMPROVEMENT PROGRAM, VIKING-CIVES RESERVES THE RIGHT TO CHANGE EQUIPMENT & SPECIFICATION WITHOUT NOTICE. 14 This Owner's Manual File is Contained Within 20301003-PRESENTATION.idw 22956 Highway 61 ♦ Morley, MO 63767 ♦Phone 573-262-3545 ♦ Fax 573-262-3369 S7001: LO-PRO PIN TYPE HITCH ASSEMBLY ITEM # PART # DESCRIPTION QTY 1 20303005 LO-PRO PIN TYPE WELDMENT 1 2 20303000 LIFT ARM WELDMENT 1 3 20303001 INNER ARM WELDMENT 1 4 20427000 CYLINDER RETAINING STOP 1 5 281022A BOLT HEX 1” X 4 ½” UNC ZINC 1 6 237278 NUT HEX ELASTIC 1” UNC ZINC 1 7 281013A FLAT WASHER SAE 1” ZINC 1 8 20P010 PIN 1 ¼” X 4 3/8” UH 2 9 20P054 PIN 1” X 4 5/8” CH 1 10 3SK3410 PIN 1” X 4” 1 11 20P148A PIN 1” X 3” 2 12 3SK3460 COTTER HAIRPIN 3/16” X 3 ¾” ZINC 1 13 280536A CLINCH PIN 5/16” X 1 ¼” ZINC 3 14 280569A ROLL PIN 3/8” X 2 ½” ZINC 2 September 2007 15 212 NORTH EVANS ROAD, EVANSDALE, IOWA 50707 (319)236-7977 PH (319)236-7980 FX LO-PRO FLINK HITCH ASSEMBLY (S7004) 15 10 3 5 1 8 7 10 13 9 14 11 6 2 ITEM DRAWING NO. ALT. ITEM NO. DESCRIPTION 1 20303011 LOW-PRO QUICK LOOP OR FLINK HITCH BLANK 2 2FLKSWIV-T FLINK QUICK LINK RECIEVER LIFT ARM WELDMENT 3 20303000 4 20303001 INNER ARM WELDMENT 5 20427000 CYLINDER RETAINING STOP 6 20312013 LO-PRO FLINK HITCH GUSSET 7 281022A 81022 BOLT HEX 1 X 4 1/2 UNC ZINC 8 237278 NUT HEX ELASTIC 1 UNC ZINC 9 281013A 81013A FLATWASHER SAE 1 ZINC 10 20P054 PIN 1" X 5 1/2" 11 PIN 1 X 4 3SK3410 12 20P148A PIN 1 X 3 13 80536 3SK3460 COTTER HAIRPIN 3/16 X 3 3/4 ZINC 14 280536A 80536A CLINCH PIN 5/16 X 1 1/4 ZINC 15 280569A ROLL PIN 3/8 X 2 1/2 ZINC 4 QTY 1 1 1 1 1 3 1 1 1 1 1 2 1 1 2 EQUIPMENT MAY NOT BE EXACTLY AS SHOWN. SOME COMPONENTS MAY BE OPTIONAL TO MAINTAIN OUR ON-GOING PRODUCT AND DEVELOPMENT IMPROVEMENT PROGRAM, VIKING-CIVES RESERVES THE RIGHT TO CHANGE EQUIPMENT & SPECIFICATION WITHOUT NOTICE. 16 This Owner's Manual File is Contained Within 20301004-PRESENTATION.idw 22956 Highway 61 ♦ Morley, MO 63767 ♦Phone 573-262-3545 ♦ Fax 573-262-3369 S7004: LO-PRO FLINK HITCH ASSEMBLY ITEM # PART # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 20303011 2FLKSWIV-T 2030300 20303001 20427000 20312013 281022A 237278 281013A 20P054 3SK3410 20P148A 3SK3460 280536A 280569A September 2007 ALT PART # 81022 81013A 80536 80536A 17 DESCRPTION QTY Lo-pro quick lop or Flink hitch blank Flink quick link receiver Lift arm weldment Inner arm weldment Cylinder retaining stop Lo-pro Flink hitch gusset Bolt hex 1 x 4 ½ unc zinc Nut hex elastic 1 unc zinc Flatwasher sae 1 zinc Pin 1” x 5 ½” Pin 1 x 4 Pin 1 x 3 Cotter hair pin 3/16 x 3 ¾ zinc Clinch pin 5/16 x 1 ¼ zinc Roll pin 3/8 x 2 ½ zinc 1 1 1 1 1 3 1 1 1 1 1 2 1 1 2 212 NORTH EVANS ROAD, EVANSDALE, IOWA 50707 (319)236-7977 PH (319)236-7980 FX LO-PRO QUICK LOOP HITCH ASSEMBLY S7003 14 15 2 12 10 5 1 9 13 8 7 11 13 6 4 ITEM DRAWING NO. ALT. ITEM NO. DESCRIPTION 1 20303011 LOW-PRO QUICK LOOP OR FLINK HITCH BLANK 2 20303000 LIFT ARM WELDMENT 3 20303001 INNER ARM WELDMENT 4 202600042A PIN RECEIVER ASSEMBLY 5 20427000 CYLINDER RETAINING STOP 6 20312012 LO PRO QUICK LOOP HITCH GUSSET 7 20P054 PIN 1 X 4 5/8 CH 8 PIN 1" X 4" 3SK3410 9 281022A 81022 BOLT HEX 1 X 4 1/2 UNC ZINC 10 237278 NUT HEX TOPLOCK 1" UNC ZINC 11 281013A 81013A FLATWASHER SAE 1" ZINC 12 HW30A-06 NUT HEX 3/8 UNC ZINC 13 3SK3460 80536 COTTER HAIRPIN 3/16" X 3 3/4" ZINC 14 280569A ROLL PIN 3/8 X 2 1/2 ZINC 15 20P148A PIN 1 X 3 QTY 1 1 1 1 1 3 1 1 1 1 1 2 2 2 2 3 EQUIPMENT MAY NOT BE EXACTLY AS SHOWN. SOME COMPONENTS MAY BE OPTIONAL TO MAINTAIN OUR ON-GOING PRODUCT AND DEVELOPMENT IMPROVEMENT PROGRAM, VIKING-CIVES RESERVES THE RIGHT TO CHANGE EQUIPMENT & SPECIFICATION WITHOUT NOTICE. 18 This Owner's Manual File is Contained Within 20301015-PRESENTATION.idw 22956 Highway 61 ♦ Morley, MO 63767 ♦Phone 573-262-3545 ♦ Fax 573-262-3369 S7003: LO-PRO QUICK LOOP HITCH ASSEMBLY ITEM # PART # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 20303011 20303000 20303001 202600042A 20427000 20312012 20P054 3SK3410 281022A 237278 281013A HW30A-06 3SK3460 280569A 20P148A September 2007 ALT PART # 81022 81013A 80536 19 DESCRIPTION QTY Lo-pro quick loop or Flink blank hitch Lift arm weldment Inner arm weldment Pin receiver assembly Cylinder retaining stop Lo-pro quick loop hitch gusset Pin 1 x 4 5/8 CH Pin 1 x 4 Bolt hex 1 x 4 ½ unc zinc Nut hex toplock 1” unc zinc Flatwasher sae 1” zinc Nut hex 3/8 unc zinc Cotter hairpin 3/16 x 3 ¾ zinc Roll pin 3/8 x 2 ½ zinc Pin 1 x 3 1 1 1 1 1 3 1 1 1 1 1 2 2 2 2 212 NORTH EVANS ROAD, EVANSDALE, IOWA 50707 (319)236-7977 PH (319)236-7980 FX UNIVERSAL TILT FLINK HITCH ASSEMBLY (S7014) 18 4 11 1 14 8 6 15 13 14 14 9 12 14 17 16 10 3 5 7 2 ITEM DRAWING NO. ALT. ITEM NO. 1 20303013 2 2FLKSWIV-T 3 20303004 4 20303000 5 20303001 6 20427000 7 20312013 8 20900004 9 20P054 10 3SK3410 11 20P148A 12 281029 13 281022A 81022 14 237278 15 HW30A-06 16 281013A 81013A 17 280536A 80536A 18 3SK3460 80536 DESCRIPTION LOWER TILT SECTION FLINK OR QUICK LOOP WELD'T FLINK QUICK LINK RECIEVER UPPER TILT WELDMENT LIFT ARM WELDMENT INNER ARM WELDMENT CYLINDER RETAINING STOP LO-PRO FLINK HITCH GUSSET PIN 1.000 DIA X 3.406 PIN 1" X 5 1/2" PIN 1 X 4 PIN 1 X 3 BOLT HEX 1 X 5 1/2 UNC ZINC BOLT HEX 1 X 4 1/2 UNC ZINC NUT HEX ELASTIC 1 UNC ZINC NUT HEX 3/8 UNC ZINC FLATWASHER SAE 1 ZINC CLINCH PIN 5/16 X 1 1/4 ZINC ROLL PIN 3/8 X 2 1/2 ZINC QTY 1 1 1 1 1 1 3 2 1 1 2 2 1 3 2 1 1 5 EQUIPMENT MAY NOT BE EXACTLY AS SHOWN. SOME COMPONENTS MAY BE OPTIONAL TO MAINTAIN OUR ON-GOING PRODUCT AND DEVELOPMENT IMPROVEMENT PROGRAM, VIKING-CIVES RESERVES THE RIGHT TO CHANGE EQUIPMENT & SPECIFICATION WITHOUT NOTICE. 20 This Owner's Manual File is Contained Within 20301005-PRESENTATION.idw 22956 Highway 61 ♦ Morley, MO 63767 ♦Phone 573-262-3545 ♦ Fax 573-262-3369 S7014: UNIVERSAL TILT FLINK HITCH ASSEMBLY ITEM PART # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 20303013 2FLKSWIV-T 20303004 20303000 20303001 20427000 20312013 20900004 20P054 3SK3410 20P148A 281029 281022A 237278 HW30A-06 281013A 280536A 3SK3460 September 2007 ALT PART # 81022 81013A 80536A 80536 DESCRIPTION Lower tilt section Flink or quick loop weld’t Flink quick link receiver Upper tilt weldment Lift arm weldment Inner arm weldment Cylinder retaining stop Lo-pro Flink hitch gusset Pin 1.000 dia x 3.406 Pin 1 x 5 ½ Pin 1 x 4 Pin 1 x 3 Bolt hex 1 x 5 ½ unc zinc Bolt hex 1 x 4 ½ unc zinc Nut hex elastic 1 unc zinc Nut hex 3/8 unc zinc Flatwasher sae 1 zinc Clinch pin 5/16 x 1 ¼ zinc Roll pin 3/8 x 2 ½ zinc 21 QT Y 1 1 1 1 1 1 3 2 1 1 2 2 1 3 2 1 1 5 212 NORTH EVANS ROAD, EVANSDALE, IOWA 50707 (319)236-7977 PH (319)236-7980 FX UNIVERSAL TILT QUICK LOOP HITCH ASSEMBLY (S7013) 12 8 1 12 9 16 7 14 15 4 13 15 10 12 18 17 11 2 5 6 ITEM DRAWING NO. ALT. ITEM NO. 1 20303013 2 20303004 3 202600042A 4 20303000 5 20303001 6 20312012 7 20427000 8 20P148A 9 20900004 10 20P054 11 3SK3410 12 280569A 13 281029 14 281022A 81022 15 237278 16 HW30A-06 17 281013A 81013A 18 280536A 80536A DESCRIPTION LOWER TILT FLINK OR QUICK LOOP WELD'T UPPER TILT WELDMENT PIN RECEIVER ASSEMBLY LIFT ARM WELDMENT INNER ARM WELDMENT LO PRO QUICK LOOP HITCH GUSSET CYLINDER RETAINING STOP PIN 1 X 3 PIN 1.000 DIA X 3.406 PIN 1 X 4 5/8 CH PIN 1" X 4" ROLL PIN 3/8 X 2 1/2 ZINC BOLT HEX 1 X 5 1/2 UNC ZINC BOLT HEX 1 X 4 1/2 UNC ZINC NUT HEX TOPLOCK 1" UNC ZINC NUT HEX 3/8 UNC ZINC FLATWASHER SAE 1" ZINC CLINCH PIN 5/16 X 1 1/4 ZINC QTY 1 1 1 1 1 3 1 2 2 1 1 5 2 1 3 2 1 1 3 EQUIPMENT MAY NOT BE EXACTLY AS SHOWN. SOME COMPONENTS MAY BE OPTIONAL TO MAINTAIN OUR ON-GOING PRODUCT AND DEVELOPMENT IMPROVEMENT PROGRAM, VIKING-CIVES RESERVES THE RIGHT TO CHANGE EQUIPMENT & SPECIFICATION WITHOUT NOTICE. 22 This Owner's Manual File is Contained Within 20301016-PRESENTATION.idw 22956 Highway 61 ♦ Morley, MO 63767 ♦Phone 573-262-3545 ♦ Fax 573-262-3369 S7013: UNIVERSAL TILT QUICK LOOP HITCH ASSEMBLY ITEM # PART # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 20303013 20303004 202600042A 20303000 20303001 20312012 20427000 20P148A 20900004 20P054 3SK3410 280569A 281029 281022A 237278 HW30A-06 281013A 280536A September 2007 ALT PART # 81022 81013A 80536A 23 DESCRIPTION QTY Lower tilt Flink or quick loop weld’t Upper tilt weldment Pin receiver assembly Lift arm weldment Inner arm weldment Lo-pro quick loop hitch gusset Cylinder retaining stop Pin 1 x 3 Pin 1.000 dia x 3.406 Pin 1 x 4 5/8 CH Pin 1 x 4 Roll pin 3/8 x 2 ½ zinc Bolt hex 1 x 5 ½ unc zinc Bolt hex 1 x 4 ½ unc zinc Nut hex toplock 1” unc zinc Nut hex 3/8 unc zinc Flatwasher sae 1” zinc Clinch pin 5/16 x 1 ¼ zinc 1 1 1 1 1 3 1 2 2 1 1 5 2 1 3 2 1 1 24 This Owner's Manual File is Contained Within 202600042-PRESENTATION.i ITEM 1 2 3 4 5 6 7 DRAWING NO. ALT. ITEM NO. 202603003 202603002 202603001 202600134 3SK3610 81083 3SK3600 3SK3670 7 QTY 1 1 1 1 2 1 3 5 5 7 3 EQUIPMENT MAY NOT BE EXACTLY AS SHOWN. SOME COMPONENTS MAY BE OPTIONAL TO MAINTAIN OUR ON-GOING PRODUCT AND DEVELOPMENT IMPROVEMENT PROGRAM, VIKING-CIVES RESERVES THE RIGHT TO CHANGE EQUIPMENT & SPECIFICATION WITHOUT NOTICE. DESCRIPTION PIN AND LOOP WELDMENT ARM WELDMENT PIN WELDMENT ARM CONNECTING LUG BOLT HEX 1/2 X 2 UNC ZINC BOLT HEX 1/2" X 1 1/2" UNC ZINC NUT HEX 1/2 UNC ZINC 6 2 7 PIN AND LOOP RECEIVER WITH OUTER LUGS S13300 22956 HWY 61 MORLEY, MO 63767 (573)262-3545 PH (573)262-3369 FX 4 1 22956 Highway 61 ♦ Morley, MO 63767 ♦Phone 573-262-3545 ♦ Fax 573-262-3369 NOTES: ____________________________________ ____________________________________ ____________________________________ ____________________________________ ____________________________________ ____________________________________ ____________________________________ ____________________________________ ____________________________________ ____________________________________ ____________________________________ ____________________________________ ____________________________________ ____________________________________ ____________________________________ ____________________________________ ____________________________________ September 2007 25