Download Operators Manual

Appendices
Error Message
513
514
515
516
518
519
520
521
523
527
529
530
533
534
536
543
545
546
547
549
550
553
554
555
556
557
558
559
560
563
565
566
600
601
602
700
701
702
703
800
801
802
803
900
901
902
903
904
905
906
907
908
909
910
F
STA_EDITDIGIT "Edit digit out of range"
DDE
STA_EDITCHG
"Can't switch edit field now"
DDE
STA_NOTEDITING "Not editing output now"
DDE
STA_BADDBMTIME "dBm not available now"
DDE
STA_OVERLOCK
"Value outside locked range"
DDE
STA_NOUNIT
"Must specify an output unit"
DDE
STA_TOOMANYF
"Can't do two freqs at once"
DDE
STA_THREEMAGS "Can't source 3 values at once"
DDE
STA_NOCANDO
"Can't do that now"
DDE
STA_NOCHANGES "No changes except RESET now"
DDE
STA_EDITACDC
"Cannot edit to or from 0 Hz"
DDE
STA_IMAGE
"Bad state image - not loaded"
DDE
STA_SET_OFFSET "Can't set an offset now"
DDE
STA_SET_RNGLCK "Can't lock this range"
DDE
STA_SET_WAVE
"Can't set wave now"
DDE
STA_EPD
"STA couldn't update OTD"
D|DDE
STA_NOEDIT
"Can't edit now"
DDE
STA_SET_TRIG
"Can't set trigger to that now"
DDE
STA_SET_OZ
"Can't set output imp. now"
DDE
STA_NEGTIME
"Period must be >= 0"
DDE
STA_RPTRUN
"A report is already printing"
DDE
STA_SET_TMWAVE "Can't set marker shape now"
DDE
STA_SET_VIDEO "Can't set video parameter now"
DDE
STA_BADVIDMARK "Marker location out of range"
DDE
STA_BADPWIDTH "Pulse width must be 1 - 255"
DDE
STA_SETRNGFUNC "Can't set range directly now"
DDE
STA_SETRNGRNG "Not a range for this function"
DDE
STA_SETTDPULSE "Can't set TD pulse now"
DDE
STA_ZEROMEAS
"ZERO_MEAS only for C meas"
DDE
STA_TLIMIT
"Time limit must be 1s-60s"
DDE
STA_OPT_5
"5820A-5 option not installed"
DDE
STA_NOFREQ
"Cannot enter frequency now"
DDE
MAIN_WATCHDOG "Outguard watchdog timeout"
B|D|DDE
MAIN_RAMTEST
"Power-up RAM test failed"
B|DDE
MAIN_GPIBTEST "Power-up GPIB test failed"
B|DDE
NV_RECORD
"Saving to NV memory failed"
R|DDE
NV_EMPTY
"NV memory invalid"
R|DDE
NV_DEFAULTS
"NV invalid so default loaded"
R|DDE
NV_OUTOFDATE
"NV obsolete so default loaded"
R|DDE
SER_PARITY
"Serial parity error %s"
B|DDE
SER_FRAMING
"Serial framing error %s"
B|DDE
SER_OVERRUN
"Serial overrun error %s"
B|DDE
SER_DROPPED
"Serial characters dropped %s"
B|DDE
STA_NO_VALUES "Cannot enter a value in this mode"
DDE
to be displayed on front panel, error message must stop here>.
STA_NO_SACVF
"Try F betw. 10 Hz & 10 kHz"
DDE
STA_NO_SACVV
"Try V betw. 1 mV & 130V "
DDE
STA_NO_SDCVV
"Try V < 130 V"
DDE
STA_NO_SGF
"Try F betw. .01 Hz & 100 kHz"
DDE
STA_NO_SGV50
"Try V betw 1.8mV & 2.5V"
DDE
STA_NO_SGV1M
"Try V betw 1.8mV & 55V"
DDE
STA_NO_SEF
"Try F betw. 900 Hz & 11 MHz"
DDE
STA_NO_SEV
"Try V betw. 3.6 mV & 2.75V"
DDE
STA_NO_SLF
"Try F betw. 50 kHz & 600 MHz"
DDE
STA_NO_SLV
"Try V betw. 5 mV & 5.5V"
DDE
F-3