Transcript
05/ 2012 30 60 12 Cal. 5020.B 45 3 9 20 10 6 15 30 23 65,5% = 40mm Druchmesser English User’s Manual Battery type: 395 (diameter 9.5mm x 2.6mm / SR 927 SW) Accuracy: +20 / -10 seconds per month Push-button A Hour counter Description of the display and control buttons (Start / Stop / Reset) 30 65,5% = 40mm Druchmesser 60 12 Display elements Control buttons 20 45 3 9 6 15 10 30 23 Push-button A Minute counter 30 20 Centre stop-second 45 3 9 Hour counter 6 10 15 30 Crown 30 Push-button B 23 Second hand Minute counter 60 12 45 3 9 6 A. Zero positioning: Press push-button B . (The 3 chronograph hands will be reset to their zero positions). 60 12 20 Example: Start: Press push-button Stop: to stop the timing, press pushbutton A once more and read the 3 chronograph counters: 4h / 20 min / 38 sec Minute hand Hour hand Chronograph: Basic function 15 10 30 65,5% = 40mm2 3Druchmesser 5% = Date 40mm Druchmesser Push-button B Hour counter Chronograph: Accumulated timing Push-button A 5% = 40mm Druchmesser 30 60 12 45 3 9 20 6 10 15 30 Example: Start: Stop: 60 (start timing) 65,5% = 40mm Druchmesser (e.g. 15 min 5 sec following ) 12 * Stop: (e.g. 10 min 5 sec following = 25 min 10 sec 45 3 9 20 6 15 10 Restart: (timing is resumed) 23 Minute counter Chronograph: Intermediate or interval timing Push-button A 30 30 23 ) Push-button B Minute counter (The accumulated measured time is shown) 30 45 3 6 Reset: The three chronograph hands are returned to their zero positions. 60 12 9 20 10 15 30 2 3 Druchmesser ,5% = 40mm Push-button B 30 60 12 20 45 3 9 Please note: 65,5% * Following , the accumulation of the 65,5% timing can be continued by pressing push-button A (Restart / Stop, Restart / Stop, …) 6 65,5% = 40mm Druchmesser 15 10 Example: Start: (start timing) Display interval: e.g. 10 minutes 10 seconds (timing continues in the background) Making up the measured time: * (the 3 chronograph hands are quickly advanced to the ongoing measured time). Stop: (Final time is displayed) Reset: The 3 chronograph hands are returned to their zero position Please note: = * Following , further intervals or inter = 40mm 40mm Druchmesser Druchmesser 65,5% = 40mm Druchmesser mediates can be displayed by pressing 30 - 65,5% = 40mm Druchmesser push-button B (display interval / make up 23 measured time, ...) Push-button B 65,5% = 40mm Druchmesser Center stop-second Hour counter 30 60 5% = 40mm Druchmesser 12 45 3 9 20 6 10 15 30 I II III Adjusting the chronograph hands to zero position Example: One or several chronograph hands are not in their correct zero positions and have to65,5% be adjusted (e.g. following a battery change). Adjusting the centre stop second A 65,5% = 40mm Druchmesser A SingleDruchmesser step 1 x short 65,5% = 40mm A Continuous long III III B Minute counter III B III Adjusting the minute counter hand III A Pull out the crown to position III (all 3 chronograph hands are in their correct or incorrect zero position). 23 Adjusting the next hand = 40mm Druchmesser and the hour counter hand (mechanical coupled) A Single step A Continuous III 1 x short long Push-button A 30 20 45 3 6 Keep push-buttons A and B depressed simultaneously for at least 2 seconds (the centre stop-second rotates by 360° corrective mode is activated). 60 12 9 10 15 30 III Returning the crown to position III I III 5% = 40mm2 3Druchmesser I Termination of the chronograph hands adjustment (can be carried out at any time). III II 65,5% = 40mm Druchmesser Push-button B Setting the time Second hand 30 60 5% = 40mm Druchmesser 12 45 3 9 20 6 10 15 Setting the date (quick mode) * Pull out the crown to position (the watch stops). III 30 65,5% = 40mm Druchmesser 12 II 45 3 9 20 30 I 60 6 10 15 III I Turn the crown until you reach the correct time 8:45 . 23 Pull out the crown to position continues to run). II (the watch 30 Turn the crown until the correct date 1 appears. II 31 Push the crown back into position * Push the crown back into position 30 60 12 20 45 3 9 6 10 15 30 I II III 5% = 40mm2 3Druchmesser Crown 30 60 5% = 40mm Druchmesser 12 45 3 9 20 6 10 15 30 I II 17 I. Please note: * In order to set the time to the exact second, must be pulled out when the second hand is in position «60» (I). Once the hour and minute hands have been set, must be pushed back into position at the exact second. 30 20 45 3 6 10 15 30 I II 65,5% = 40mm0 1Druchmesser I Setting the date/time Example: – Date / time on the watch: – Present date / time: Please note: During the date changing phase between 9 PM and 12 PM; the date must be set to the date of the following day. 60 12 9 17 4 Pull out the crown to position (the watch continues to run). / 1:25 AM / 8:30 PM 30 60 65,5% = 40mm Druchmesser 12 45 3 9 20 6 10 30 30 I II II III 03 45 3 6 10 ** Continue to turn the crown until the correct time 8:30 PM appears. 30 I 03 45 3 9 20 6 I. 60 12 15 30 III Turn the crown until the correct date 4 appears. Push the crown back into position 60 12 * Pull out the crown to position (the watch stops). 15 Turn the crown until yesterday’s date appears 3 9 An extreme acceleration in setting the date with quick mode can induce a false date indi cation.The synchronization is re-established by setting the date from 01 till 31 (crown in position II). Second hand Date 20 I. 10 15 30 II I 04 II III Please note: * To set your watch to the exact second, please refer to the chapter entitled «setting the time». ** Please observe the AM/PM clock rhythm. -