Transcript
1 ⁄ 10 second counter 9 10 1 8 7 6 30 20 4 5 Push-button A Chronograph: Basic function (Start / Stop / Reset) 2 3 Example: Start: Press push-button 23 10 60 45 9 10 1 8 7 6 5 30 Cal. 3540.D 20 4 30 2 3 Minute counter 23 10 60 45 9 10 1 8 7 15 6 30 30 20 4 5 A. Stop: to stop the timing, press push-button A once more and read the 3 chronograph counters: 4 min / 38 sek / 7⁄ 10 sec 15 Zero positioning: Press push-button B . (The 3 chronograph hands will be reset to their zero positions). 2 3 23 10 60 45 English User’s Manual 30 Push-button B 05 Description of the display and control buttons Display elements Chronograph: Accumulated timing 1 ⁄ 10 second counter 9 10 1 8 7 6 30 Control buttons 20 Minute hand 5 4 2 3 45 8 7 ⁄ 10 second counter 30 (hour counter after 30 minutes) 20 9 10 1 6 5 4 2 3 10 Hour hand 15 Crown 9 10 1 8 7 Push-button B 6 30 30 20 5 4 * Stop: 10 Date 15 30 01 Push-button B 06 Setting the time 6 30 5 4 1 ⁄ 10 second counter Push-button A * Pull out the crown to position (the watch stops). 60 45 II III 15 30 8 7 6 30 5 4 23 10 I 60 45 II III 15 30 02 9 10 1 6 30 20 5 4 2 3 45 I. Please note: * In order to set the time to the exact second, must be pulled out when the second hand is in position «60» (I). Once the hour and minute hands have been set, must be pushed back into position at the exact second. Pull out the crown to position continues to run). I 60 45 15 30 9 10 1 8 7 6 30 20 5 4 Push-button B 2 3 Please note: * Following , further intervals or inter mediates can be displayed by pressing push-button B (display interval / make up measured time, ...) 15 I 30 Push-button B 07 1 ⁄ 10 second counter Centre stop-second 9 10 1 8 7 II (the watch 6 30 II 5 4 2 3 I 60 45 II Adjusting the chronograph hands to zero position Example: One or several chronograph hands are not in their correct zero positions and have to be adjusted (e.g. following a battery change). 23 10 Turn the crown anticlockwise until the correct date 1 appears. 15 Example: Start: (start timing) Display interval: e.g. 10 minutes 10 seconds (timing continues in the background) Making up the measured time: * (the 3 chronograph hands are quickly advanced to the ongoing measured time). Stop: (Final time is displayed) Reset: The 3 chronograph hands are returned to their zero position 60 20 30 III 15 Pull out the crown to position III (all 3 chronograph hands are in their correct or incorrect zero position). 30 Minute counter 8 7 9 10 1 6 30 20 5 4 Push the crown back into position I. 9 10 1 8 7 2 3 6 30 1 10 20 I 60 45 10 Please note: During the date changing phase between 08.30 PM and 12 PM; the date must be set to the date of the following day. II 15 30 03 ) Chronograph: Intermediate or interval timing 23 10 45 31 10 23 Minute counter Setting the date (quick mode) 8 7 4 10 Turn the crown until you reach the correct time 8:45 . * Push the crown back into position 2 3 5 2 3 60 Second hand 9 10 1 6 30 20 I 9 10 1 8 7 III 23 10 (e.g. 13 min 5 sec following = 28 min 10 sec Please note: * Following , the accumulation of the timing can be continued by pressing push-button A (Restart / Stop, Restart / Stop, …) 60 2 3 ) Reset: The 3 chronograph hands are returned to their zero positions. 2 3 23 45 9 10 1 (e.g. 15 min 5 sec following Restart: (timing is resumed) 15 (The accumulated measured time is shown) Second hand 8 7 (start timing) Stop: Minute counter 60 45 20 Example: Start: 30 Push-button A 23 Minute counter 20 Push-button A 23 10 60 Centre stop-second 1 15 5 4 Push-button A Keep push-buttons A and B depressed simultaneously for at least 2 seconds 2 3 (the centre stop-second rotates by 65,5% = 40mm Druchmesser 360° 23 corrective mode is activated). III 65,5% = 40mm Druchmesser 65,5% = 40mm Druchmesser Push-button B = 40mm Druchmesser 65,5% 60 45 15 30 65,5% = 40mm Druchmesser 65,5% = 40mm Druchmesser 8 7 9 10 1 6 30 20 5 4 Crown 2 3 Example: – Date / time on the watch: – Present date / time: 17 10 I 60 45 II 21 21 17 4 Pull out the crown to position (the watch continues to run). 15 30 9 10 1 6 30 5 4 9 10 1 5 4 I * Pull out the crown to position (the watch stops). 2 3 3 10 I 60 45 II III Second hand 30 9 10 1 6 5 4 4 I 60 45 15 30 04 Turn the crown until the correct date 4 appears. II III I Termination of the chronograph hands adjustment (can be carried out at any time). Battery type: 384 (diameter 7.9 mm x 3.6 mm / SR 41 SW) Accuracy: +20 / -10 seconds per month I. 2 3 10 III 03/ 2013 ** Continue to turn the crown until the correct time 8:30 PM appears. Push the crown back into position II III 15 30 8 7 III III III Returning the crown to position 15 6 1 x short long B III II 08 8 7 III Adjusting the minute counter (position 9h) III A 1 x short Single step A long Continuous A 30 30 A A 21 I 45 10 Adjusting the next hand 3 60 20 Single step Continuous 21 21 Turn the crown anticlockwise until 3. yesterday’s date appears 2 3 10 20 1 A II B 8 7 III Adjusting the next hand B 65,5% = 40mm Druchmesser B III 65,5% = 40mm Druchmesser Adjusting the ⁄ second counter hand (position 6h) / 1:25 AM / 8:30 PM Date 20 Adjusting the centre stop second A Single step 1 x short A Continuous long A Setting the date/time Please note: * To set your watch to the exact second, please refer to the chapter entitled «setting the time». ** Please observe the AM/PM clock rhythm.