Transcript
30 45 3 9 20 www.ronda-startech.com 60 12 Cal. 5020.B 10 6 15 30 23 Battery type: 395 (diameter 9.5mm x 2.6mm / SR 927 SW) Accuracy: +20 / -10 seconds per month 65,5% = 40mm Druchmesser English User’s Manual In case your watch needs to be repaired or to raise claims under a guarantee, please contact the point of sales 30 (Start / Stop / Reset) 65,5% = 40mm Druchmesser 60 12 Display elements Chronograph: Basic function Push-button A Hour counter Description of the display and control buttons Control buttons 20 45 3 9 6 15 10 30 Push-button A Minute counter 30 20 45 3 6 Centre stop-second 10 15 Crown 30 Zero positioning: 30 Push-button B 23 Second hand Minute counter 60 12 9 Hour counter 45 3 9 20 6 15 10 30 65,5% = 40mm 2 3 Druchmesser Push-button B Hour counter Chronograph: Accumulated timing Push-button A ,5% = 40mm Druchmesser 30 60 12 45 3 10 15 30 30 45 3 6 10 12 45 3 9 20 6 15 10 30 23 15 (The accumulated measured time is shown) Please note: 65,5% * Following , the accumulation of the 65,5% timing can be continued by pressing push-button A (Restart / Stop, Restart / Stop, …) 2 3 Druchmesser ,5% = 40mm Push-button B Push-button B Minute counter = 25 min 10 sec Reset: The three chronograph hands are returned to their zero positions. 30 Example: Start: (start timing) Display interval: e.g. 10 minutes 10 seconds (timing continues in the background) * Making up the measured time: (the 3 chronograph hands are quickly advanced to the ongoing measured time). Stop: (Final time is displayed) Reset: The 3 chronograph hands are returned to their zero position 65,5% = 40mm Druchmesser *Stop: (e.g. 10 min 5 sec following ) 60 12 9 20 Example: Start: (start timing) 60 Restart:(timing is resumed) Minute counter Chronograph: Intermediate or interval timing Push-button A 30 Stop: (e.g. 15 min 5 sec following ) 23 Press push-button B. (The 3 chronograph hands will be reset to their zero positions). 60 12 ,5% =Date 40mm Druchmesser 6 pushbutton A once more and read the 3 chronograph counters: 4h / 20 min / 38 sec 23 Hour hand 9 Example: Start: Press push-button A. Stop: to stop the timing, press Minute hand 20 11 / 2008 Ronda AG CH-4415 Lausen/Switzerland 30 60 12 45 3 9 20 6 65,5% = 40mm Druchmesser 15 10 Please note: = * Following , further intervals or inter= 40mm 40mm Druchmesser Druchmesser 65,5% = 40mm Druchmesser mediates can be displayed by pressing 30 65,5% =40mm Druchmesser push-button B (display interval / make up 23 measured time, ...) Push-button B 65,5% = 40mm Druchmesser Center stop-second Hour counter 30 60 ,5% = 40mm Druchmesser 12 45 3 9 20 6 10 15 30 I II III Adjusting the centre stop second A 65,5% = 40mm Druchmesser SingleDruchmesser step A 1 x short 65,5% = 40mm Continuous A long Adjusting the chronograph hands to zero position Example: One or several chronograph hands are not in their correct zero positions and have to be 65,5% adjusted (e.g. following a battery change). III III B = 40mm Druchmesser A Pull out the crown to position III (all 3 23 chronograph hands are in their correct or incorrect zero position). Minute counter III Push-button A Keep push-buttons A and B depressed 30 45 3 6 60 12 9 20 10 15 30 III ,5% = 40mm Druchmesser 23 12 45 3 9 6 10 III 15 II III II 65,5% = 40mm Druchmesser *Pull out the crown to position III (the watch stops). Setting the date (quick mode) 30 60 12 45 3 9 20 6 10 I Turn the crown until you reach the correct Pull out the crown to position II (the watch continues to run). 15 30 III 23 65,5% = 40mm Druchmesser 30 I III position I Returning the crown to Setting the time 60 ,5% = 40mm Druchmesser 20 Adjusting the hand and the hour counter hand (mechanical coupled) A 1 x short Single step Continuous A long Second hand III III minute III counter Termination of the chronograph hands adjustment (can be carried out at any time). I Push-button B 30 simultaneously for at least 2 seconds (the centre stop-second rotates by 360° corrective mode is activated). Adjusting the next hand B Turn the crown until the correct II date 1 appears. 31 time 8:45. Push the crown back into position I. *Push the crown back into position I. 30 20 45 3 9 6 60 12 10 Please note: * In order to set the time to the exact second, must be pulled out when the second hand is in position «60» (I). Once the hour and minute hands have been set, must be pushed back into position I at the exact second. 15 30 I II III ,5% = 40mm 2 3 Druchmesser 30 60 ,5% = 40mm Druchmesser 12 45 3 9 6 10 15 30 I 20 45 3 6 10 II 15 I II Example: – Date / time on the watch: 17 / 1:25 AM 4 / 8:30 PM – Present date / time: Second hand 30 * Pull out the crown to position III 60 65,5% = 40mm Druchmesser 12 45 3 9 20 6 10 30 I (the watch continues to run). II appears 3 20 45 3 6 10 30 appears. correct time 8:30 PM appears. 20 30 45 3 9 6 60 12 15 I 4 **Continue to turn the crown until the Push the crown back into position I. 60 12 (the watch stops). Turn the crown until the correct date III 03 Turn the crown until yesterday’s date 30 15 Date 9 An extreme acceleration in setting the date with quick mode can induce a false date indication. The synchronization is re-established by setting the date from 01 till 31 (crown in position II). 30 65,5% = 40mm 0 1 Druchmesser Pull out the crown to position II 17 Please note: During the date changing phase between 9 PM and 12 PM; the date must be set to the date of the following day. 60 12 Setting the date/time Crown 20 30 9 10 15 30 II I 03 04 II III Please note: *To set your watch to the exact second, please refer to the chapter entitled «setting the time». ** Please observe the AM/PM clock rhythm.