Transcript
RONDA startech – Movement Cal. 5020.B 30 You have decided to buy a watch, which was assembled by a watchmaker using a Ronda movement. Please note that no watches are produced or distributed under the Ronda Brand. 20 45 3 9 Example: Start: Press push-button A. 15 10 6 (Start / Stop / Reset) 60 12 30 Stop: to stop the timing, press 23 In case of repairs, guarantee claims and questions concerning the functioning of a watch, purchasers and consumers should contact their retailer or the watch manufacturer, for which the relevant information can be found in the sales or guarantee documentation provided with the watch. B A 30 45 3 9 20 Press push-button B. (The chronograph hands will be reset to their zero positions.) 15 10 6 30 23 B Description of the display and control buttons A 30 45 3 9 20 6 60 12 Control buttons Stop: (e.g. 15 min 5 sec following ) 30 Restart:(timing is resumed) 23 Minute counter 60 12 20 Hour counter 45 3 6 10 Second counter 15 30 A Crown 30 Push-button B 23 20 45 3 9 6 15 10 Date Setting the time 30 45 3 6 10 II III 45 3 10 I 23 II III B 45 3 6 60 12 9 10 45 3 9 6 10 30 I 01 10 15 30 I 23 An extreme acceleration in setting the65,5% date 65,5% with quick mode can induce a false date indication. The synchronization is re-established by setting the date from 01 till 31 (crown in position II). 15 II B 03 60 45 3 6 1 Please note: During the date changing phase between approx. 9 PM and 12 PM; the date must be set to the date of the following day. II 30 45 3 6 10 Pull out the crown to position III (all chronograph hands are in their correct or incorrect zero position). Keep push-buttons A and B depressed 30 simultaneously for at least 2 seconds (the 65,5% = 40mm Druchmesser second counter hand rotates by 60 12 360° corrective mode is activated). = = 40mm 40mm Druchmesser Druchmesser 65,5% = 40mm Druchmesser III 45 3 9 20 6 15 10 30 65,5% = 40mm Druchmesser 23 B 30 I II III III B = 40mm Druchmesser A Pull out the crown to position II 17 Adjusting the second counter hand A 65,5% = 40mm Druchmesser A 1 x short SingleDruchmesser step 65,5% = 40mm Continuous A long Example: – Date / time on the watch: 17 / 1:25 AM 65,5% 4 / 8:30 PM – Present date / time: 15 (the watch continues to run). B III Turn the crown until A 30 45 3 6 10 30 A 45 3 6 10 Adjusting the hand and the hour counter hand (mechanical coupled) A 1 x short Single step Continuous A long III position I Returning the crown to II III 08 * Pull out the crown to position III 60 12 III III minute III counter II B 30 Adjusting the next hand B III Termination of the chronograph hands adjustment (can be carried out at any time). I I 20 15 03 9 yesterday’s date appears 3 . 60 12 9 20 Example: One or several chronograph hands are not in their correct zero positions and have to be adjusted (e.g. following a battery change). A Setting the date/time 60 12 9 20 III B 65,5% = 40mm Druchmesser A Adjusting the chronograph hands to zero position A Push the crown back into position I. 60 B 12 appears. B Please note: * Following , further intervals or intermediates can be displayed by pressing push-button B (display interval / make up measured time, ...). 30 30 9 Turn the crown until the correct date II A 20 15 10 23 20 I 12 45 3 6 07 continues to run). 15 31 60 12 9 20 Pull out the crown to position II (the watch 30 30 30 Setting the date (quick mode) A 30 A Please note: * In order to set the time to the exact second, must be pulled out when the second hand is in position «60». Once the hour and minute hands have been set, must be pushed back into position I at the exact second. 15 30 02 B *Push the crown back into position I. 60 12 20 30 23 time 8:45. Example: Start: (start timing) Display interval: e.g. 20 minutes 17 seconds (timing continues in the background) * Making up the measured time: (The chronograph hands are quickly advanced to the ongoing measured time.) Stop: (Final time is displayed) Reset: The chronograph hands are returned to their zero position 15 10 Turn the crown until you reach the correct A 6 45 3 6 60 12 9 20 B 30 9 (the watch stops). 15 I 20 30 30 23 Chronograph: Intermediate or interval timing A *Pull out the crown to position III 60 12 9 20 B 06 A Please note: * Following , the accumulation of the timing can be continued by pressing push-button A (Restart / Stop, Restart / Stop, …). 30 23 01 Reset: The chronograph hands are returned to their zero positions. 60 12 Second hand *Stop:(e.g. 5 min 12 sec following ) = 20 min 17 sec (The accumulated measured time is shown) B Push-button A 30 9 Chronograph: Accumulated timing Example: Start: (start timing) 15 10 Minute hand Hour hand pushbutton A once more and read the chronograph counters: 4h / 20 min / 38 sec Zero positioning: 60 12 05 Display elements Chronograph: Basic function A User’s Manual English (the watch stops). Turn the crown until the correct date 15 30 I II III appears. 4 **Continue to turn the crown until the 03 B correct time 8:30 PM appears. Push the crown back into position I. A 30 20 45 3 9 6 60 12 10 15 30 I 04 04 B II III Please note: *To set your watch to the exact second, please refer to the chapter entitled «setting the time». ** Please observe the AM/PM clock rhythm. 06 / 2014 Battery type: 395 (diameter 9.5 mm x 2.6 mm / SR 927 SW) Accuracy: +20 / -10 seconds per month