Download Installation manual

Technical parameters
8 x IF inputs from 2xQuattro LNBs
1 x UHF/VHF input from Terrestrial antenna
Outputs
8 x loopthrough satellite IF outputs
1 x loopthrough terrestrial output
2 x Legacy output to connect to legacy receiver with combined
terrestrial signal
1 x Unicable output to connect up to 8 receiver tuners with combined terrestrial signal
Frequency range
Satellite: 950-2150MHz
Terrestrial: 47-862MHz
Loopthrough loss
Satellite: max 5 dB(Typ. 3dB)
Terrestrial: max 5 dB(Typ. 3dB)
Gain
Satellite: 10dB (max.)
Terrestrial: -15dB
Isolation
Satellite-Satellite outputs: min 30dB
Satellite-Terrestrial : min 35dB
Control protocol
DiSEqC™ commands extension according to CENELEC
prEN50494
Power consumption
19VDC, 350mA
Dimensions (W x H x D mm)
W=196 H=163 D=47 mm
Temperature range
-20C - +60C
AC/DC adaptor
Input voltage: 90-265VAC, 50/60Hz
Output voltage: 19VDC
Output current: 940mA
Short circuit protection: Yes
Dual Satellite Cascadable Unicable™ switch
With 2 legacy ports and terrestrial input
IDLP-USS2OO-CUO1O-8PP
Installation manual
Terrestrial
input
V/L
V/H
H/H
H/L
V/H
V/L
Satellite 2 - Input
H/H
H/L
Satellite 1 - Input
Unicable
Out
Power Input
+20V DC
+
Inputs
TM
Dual Satellite Cascadable Unicable Switch
Troubleshooting
Make sure the satellite antenna and LNB are properly fixed, connected and adjusted and that the
satellite receivers are installed, connected and switched on according to available instructions.
Ensure there is no short circuit on the product inputs. This will prevent power to the LNB. If this is the
case, disconnect the product from the main power, and then find and remove the short circuit on the
product inputs. Then re-connect the multiswitch to the main power.
Frequent defects are in connector joints i.e. if the central conductor is too short and fails to make
contact in the connector. Also the shielding braid should make proper contact with the connector
coat. Sometimes a reset to the multiswitch microprocessor is sufficient to remove a fault: simply
disconnect the multiswitch from main power for 30 seconds and then reconnect again.
If you are unable to remove the fault yourself, please contact your distributor.
Disposal
Following relevant EU directives, this device shall not be disposed of together with municipal waste.
Use local waste collection and recycling systems to dispose wore out products.
V030909
*DiSEqC™ is a registered trademark of Eutelsat
*For purpose of brevity, some product descriptions in this sheet remain at platform level and may not be
referred to as detailed datasheets of the products. Inverto Digital Labs reserves the right to amend, omit or
add products, product-lines, and/ or features without notice. https://rcpt.yousendit.com/734804689/01d10f5
4 24cd588e25266c997fcc287bc
2 legacy ports and Terrestrial antenna input
Legacy
Out 1
IDLP-USS2OO-CUO1O-8PP
0 : 1076.06MHz
1 : 1178.12MHz
User Bands: 2
: 1280.18MHz
3 : 1382.24MHz
4 : 1484.30MHz
5 : 1586.36MHz
6 : 1688.42MHz
7 : 1790.48MHz
Satellite inputs: IF 950-2150MHz
Satellite Loop-Through loss: -3dB
Terrestrial Loop-Through loss: -3dB
Legacy
Out 2
Terrestrial
loop through
output
Satellite 2 - loopthrough output
V/L
V/H
H/H
Satellite 1 - loopthrough output
H/L
V/L
V/H
H/H
H/L
Connect the cables from the Quattro LNBs to the input connectors marked with LNB V/L, V/H, H/L
and H/H inputs (pay attention to identification of the Quattro LNB connectors). The multiswitch is
equipped with Terrestrial input. Connect the Terrestrial antenna to this input:
Terrestrial
V/L
V/H
H/H
input
The Unicable multiswitch is designed for the distribution of satellite and terrestrial television and radio
Satellite 2 - Input
signals in home installations. The warranty does not apply for products used for other purposes than
those specified herein. The user/installer shall be responsible for any Unicable
damage incurred as a result of
Out
not using the product according to the instructions in this manual.
Warranty
H/L
V/L
V/H
H/H
Satellite 1 - Input
Terrestrial
V/L
input
Power Input
+20V DC
V/H
H/H
Satellite 2 - Input
Unicable
Out
Installation location
The product shall be installed on a wall or other hard inflammable surface.
The product shall be in no case held only with the connected cables.
Place the product in a dry environment where it is not exposed to rain or running water.
Do not install the product close to heat sources or in places exposed to direct sunlight.
There are three output connectors: 2x Legacy and 1x Unicable.
The Legacy outputs are standard Universal switching outputs that allow connecting legacy receivers
that are not supporting the Unicable protocol.
The Unicable output allows to connect up to 8 receiver tuners – each needs to be allocated one of the
8 user bands supported by the multiswitch.
Each receiver tuner is assigned with 1 out of 8 communication channel frequencies (user band). The
frequencies are
listed on the product
label:
Satellite
Cascadable
Unicable
Switch
TM
To connect the product inputs and outputs use high-quality coaxial cables designed for satellite recepDual
tion and F-connectors. Use a high-shielding coaxial cables with minimum 90dB.
If you use wall sockets to loopthrough the 8 user bands, make sure theLegacy
wall sockets were designed
2 legacy
Out 1
for satellite reception compatible with Unicable technology and allows bidirectional
signal propagation.
The following diagram describes the installation configurations supported by the product:
Quattro Quattro
LNB 1Legacy
LNB 2
Out 2
Terrestrial
loop through
output
V/L
x8 User bands
UB 5
UB 3
UB 1
UB 6
UB 4
UB 2
UB 0
Terrestrial
input
V/L
V/H
H/H
H/L
V/H
V/L
Satellite 2 - Input
H/H
H/L
Satellite 1 - Input
Unicable
Out
Power
+20V DC
0
User Bands: 1
2
3
IDLP-USS2OO-CUO1O-8PP
1 : 1076.06MHz
: 1178.12MHz
User Bands: 2
3 : 1280.18MHz
4 : 1382.24MHz
5 : 1484.30MHz
6 : 1586.36MHz
7 : 1688.42MHz
8 : 1790.48MHz
Satellite inputs: IF 950-2150MHz
Satellite Loop-Through loss: -3dB
Terrestrial Loop-Through loss: -3dB
Legacy
Out 2
Terrestrial
loop through
output
Satellite 2 - loop through output
V/L
V/H
H/H
1076.06MHz
1178.12MHz
1280.18MHz
1382.24MHz
4
5
6
7
:
:
:
:
1484.30MHz
1586.36MHz
1688.42MHz
1790.48MHz
V/L
V/H
H/H
H/L
Legacy
Out 1
V/H
V/L
Satellite 2 - Input
Unicable
Out
H/H
H/L
Satellite 1 - Input
Power Input
+20V DC
2 legacy p
TM
Dual Satellite Cascadable Unicable Switch
2 legacy ports and Terrestrial antenna input
Legacy
Out 1
IDLP-USS2OO-CUO1O-8PP
0 : 1076.06MHz
1 : 1178.12MHz
User Bands: 2
: 1280.18MHz
3 : 1382.24MHz
4 : 1484.30MHz
5 : 1586.36MHz
6 : 1688.42MHz
7 : 1790.48MHz
Satellite inputs: IF 950-2150MHz
Satellite Loop-Through loss: -3dB
Terrestrial Loop-Through loss: -3dB
Legacy
Out 2
Terrestrial
loop through
output
Satellite 2 - loopthrough output
V/L
V/H
H/H
Satellite 1 - loopthrough output
H/L
V/L
V/H
H/H
H/L
Satellite inputs: IF 950-2150MHz
Us
Satellite Loop-Through loss: -3dB
Terrestrial Loop-Through loss: -3dB
Sa
Note: Loopthrough outputs that are not used should be terminated with 75ohm DC-blocked
terminations.
TM
Legacy 2
Legacy 1
:
:
:
:
Terrestrial
input
Sa
For optimized performance, please follow the recommendations below:
Te
Legacy
1. use the highest frequency for a wall socket located the nearest to the
multiswitch and use the
Out 2
Satellite
1
loop
through
output
Satellite 2 - loopthrough output
lowest frequency for wall socket located farest to the multiswitch.
Terrestrial
2.
less than 8 receiver
lowest frequencies
Satellite 2 - loopthrough o
H/Hfirst. We also
H/L recommend
V/H
V/H
H/HIf you install H/L
V/Ltuners, use the
loop
through
to keep record of the user bands allocated to the different
connections
as
these
user
bands will
output
V/H
V/L
H/H
then have to be set in the receiver. The satellite receivers connected to the multiswitch have to
be Unicable-compatible (usually marked with Unicable™ logo).
AC
Dual Satellite Cascadable
Unicable Switch
Legacy
Out 1
IDLP-USS2OO-CUO1O-8PP
+
UB 7
Dual Sat
ports and Terrestrial antenna input
+
Product installation
Satellite 1 - loop through output
H/L
V/H
V/L
H/H
H/L
Safety
x8 User bands
UB 5
UB 3
UB 1
UB 6
UB 4
UB 2
UB 0
V/L
V/H
H/H
H/L
V/H
V/L
Satellite 2 - Input
H/H
H/L
Satellite 1 - Input
Unicable
Out
Power
+20V DC
+
UB 7
Terrestrial
input
TM
Legacy 2
Legacy 1
Dual Satellite Cascadable
Unicable Switch
Legacy
Out 1
IDLP-USS2OO-CUO1O-8PP
1 : 1076.06MHz
2 : 1178.12MHz
User Bands: 3
: 1280.18MHz
4 : 1382.24MHz
5 : 1484.30MHz
6 : 1586.36MHz
7 : 1688.42MHz
8 : 1790.48MHz
Satellite inputs: IF 950-2150MHz
Satellite Loop-Through loss: -3dB
Terrestrial Loop-Through loss: -3dB
Legacy
Out 2
Terrestrial
loop through
output
Satellite 2 - loop through output
V/L
V/H
H/H
Satellite 1 - loop through output
H/L
V/L
V/H
H/H
Terminated
Outputs
2
H/L
+
Thank you for purchasing Inverto’s advanced Unicable multiswitch and we are certain it will meet your
expectations.
Before installing and operating the product, please read the following instructions and recommendations. We suggest that you keep this manual for future use.
H/L
AC
Never open a powered product. This may result in electrical hazard.
Never work on the product, TV set or other powered devices during or before a storm. A lightning
strike into the antenna may cause dangerous overvoltage over the product’s metallic/conductive
parts.
Make sure the local electricity network corresponds to the operating voltage of the AC/DC adaptor.
If the products gets into contact with liquid it must be disconnected from the main power.
It is recommended to disconnect the product from the main power if it is not used for long periods of
time.
When disconnecting the product don’t pull the cable but the plug to prevent damage of the cable
(wobbly plugs and outlets result in fire risk).
The product shall be serviced by qualified experts only.
3