Download Technicolor - Thomson RR200PLM User's Manual
Transcript
Untitled-3 s e r m a n u a l Manuel d'utilisation U Bedienungsanleitung Manuale di utilizzazione Manual de utilización Manual de instalação G e b r u i k s a a n w i j z i n g installationsvejledning B r u k s a n v i s n i n g a y t t o o h j e B r u k e r h a n d b o k K o b s t u g i Hasznaiati Útmutató I n s t r u k c j a R R R 2 2 2 0 0 0 0 0 0 P P P L LL Pykoßoactbo no okcnnyataunhn R R R 1 L M M 7/17/01, 5:21 PM T H O M S O N multimedia 4 6 / 4 7 quai A. Le Gallo 9 2 6 4 8 B o u l og n e C E D E X F R A N C E RCS Nanterre B 322 019 464 R R 2 0 0 P L L R R 2 0 0 P L M 550 207 10 550 207 30 550 207 30 550 207 30 THE DIGITAL TUNING CLOCK RADIO MAINS CONNECTIONS (FOR UNITED KINGDOM ONLY) CAUTION: Do NOT under any circumstances plug the severed plug into any mains socket as thisConnect the power cord into could result in electric shock. Setting time 230V ~50Hz a mains power socket Do NOT make any connection to the terminal in the plug which is marked by the letter E or by the earth symbol or coloured green and yellow. A fuse plug must be fitted with a 3A fuse approved by ASTA or BSI to BS 1362 and fuse covers must always be securely replaced. If your RR-200PLL/RR-200PLM does not work, the fuse may be blown. USEFUL ADVICE .Do not use your set immediately after transport from a cold place to a warm place: there may be condensation problems. . This set uses a laser beam. To prevent any accident due to this type of beam, the set should only be opened by properlytrained personnel. . Make sure that you keep your set away from water and high temperatures. . If you do not use your set on battery power for more than one month, we advise you to take out all the batteries. . To prevent personal injury, do not reverse any battery and do not mix battery types. ECOLOGY . Help protect the environment - we recommend that you dispose of used batteries by putting them into specially designed receptacles. MAINTENANCE . Clean the unit with a soft cloth, or a damp chamois leather. Never use solvents. Untitled-3 2 M1/M6 1 4 Digital Tuning Radio M3/M8 M4/M9 M2/M7 ALARM/ CLOCK SET 1 Press SET 2 Press 3 Press 4 Press SET M5/M10 WAKE/ CLOCK + until and show to set minute - to set hour MEMO HOUR ADJ MINUTE [TUNING] SNOOZE 3 WAKE/ CLOCK to complete the setting 2 • Press and hold to skip fast - +or Adjusting display brightness You may slide HI DISPLAY LO display brightness. at the back of the unit to vary the LCD Listening to radio 1 4 WAKE 1 WAKE 2 M1/M6 SLEEP SET ALARM/ CLOCK 1 Press BAND to select FM/LW (RR-200PLL) 2 or FM/MW (RR-200PLM) 3 Press or + station VOLUME 2 Adjust min max listening level max MEMO HOUR ADJ MINUTE [TUNING] RADIO on•off ALARM off SNOOZE 3 to turn on the radio 2 M5/M10 min NAP RADIO on•off ALARM stop 1 VOLUME Digital Tuning Radio M3/M8 M4/M9 M2/M7 Press BAND INTRO-SCAN 2 4 to your desired to your desired • To improve reception, you may try and reposition the unit or extend the FM aerial wire • Press and hold for 2 sec to tune automatically +or • If stations are in memory (see Setting “ memory” for refer2 3 ence), you may skip and above and press the memory buttons to access the corresponding memorised stations directly RADIO on•off • To turn off the radio, press again ALARM stop 7/17/01, 5:21 PM THE DIGITAL TUNING CLOCK RADIO THE DIGITAL TUNING CLOCK RADIO Setting NAP GB Using INTRO-SCAN The NAP alarm allows you to take a nap for a period of 15 minutes up to 2 hours. After the set time period lapses, the Intro-scan function allows you to listen to each tuned channel for a playNAP alarm will sound to wake you up. period of up to 10 seconds. NAP Press and hold (and will 1 2 and Listening of to “ 1 Follow 1 1 light) to set the desired time interval radio” above after which the buzzer will sound 2 to start scanning 2 Press INTRO-SCAN NAP • While in NAP mode, presses on will show the remaining time before the alarm sounds. RADIO on•off • During the play period, you may: • To stop NAP buzzer from sounding, press ALARM stop - or + -- Press to keep scanning or change NAP • To turn off the NAP cycle, press and hold until scanning direction goes off -- Press MEMO to set memory (see “Setting Memory” for details) Sleep to radio • During the scanning or play period, INTRO-SCAN -- Press to exit the intro scan function You can drift off to sleep to radio knowing that the unit will turn itself off automatically. If alarm is set, the unit will turn on again as programmed. 1 WAKE 1 WAKE 2 NAP SLEEP / 6 3/ 8 M2/M7 WAKE 1 WAKE 2 NAP SLEEP M1/M6 Digital Tuning Radio M3/M8 M4/M9 M2/M7 M5/M10 / 9 min min ALARM/ CLOCK SET max SET ALARM/ CLOCK HOUR ADJ MINUTE [TUNING] MEMO HOUR ADJ MINUTE [TUNING] RADIO on•off ALARM off RADIO on•off ALARM off BAND SNOOZE INTRO-SCAN INTRO-SCAN SNOOZE Setting memory SLEEP 1 You may preset up to 10 radio channels 1 WAKE 1 WAKE 2 NAP SLEEP Tune to your desired station 2 Digital Tuning Radio M3/M8 M4/M9 M2/M7 M5/M10 ALARM/ CLOCK SET 3 M1/M6 MEMO HOUR ADJ MINUTE [TUNING] SNOOZE Press MEMO blinking 3 2 andstarts 3 SET Digital Tuni M3/M M2/M7 ALARM/ CLOCK 2 SNOO 2 Tune to your preferred station M5/M10 Press ...... to designate memory location 1. Press the memory buttons once to select M1...M5, twice to select M6...M10 MEMO 2. To exit from memory setting, press until and the location number go off Untitled-3 M1/M6 Press and hold to set the time from 2 hours to 15 minutes and will light HOUR ADJ [TUNIN RADIO on•off ALARM off M1/M6 max MEMO BAND S N O Opress ZE • If you decide to turn off the unit sooner, or RADIO on•off and this will shut off the sleep cycle. ALARM stop SLEEP • When sleep mode is active, subsequent presses on will show the remaining time before the unit goes off. • This unit allows you to “Sleep to one radio station and wake to another”(seeSetting “ alarm with music” for setting alarm(s)) • If desired radio station is not selected, the unit will sleep to the last receiving station. 7/17/01, 5:21 PM