Download Speco Technologies CVC-6246IHR User's Manual

CVC-6246iHR
540 Line Color Dome Camera
Intensifier Series
Wall & Ceiling Mountable
Please read this manual thoroughly before operation and keep
it handy for further reference.
WARNING & CAUTION
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION :
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE
REFER SERVICINGTO QUALIFIED
SERVICE PERSONNEL._______________
The lighting flash with an arrowhead symbol, within an equilateral triangle is
Intended to alert the user to the presence of un-insulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons____________________________________
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (serving) instructions
in the literature accompanying the appliance__________________
INFORMATION -This equipment has been tested and found to company with
limits for a class a digital device Pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful
Interference When the equipments operated in a commercial environment.
This equipment generates, uses, and Can Radiate radio frequency energy and
if not installed and used in accordance with the instruction manual, may Cause
Harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which
Case the user will be required to correct the interference at his own expense.
WARNING – Change or modification not expressly approved by the manufacturer could void
the user’s authority to operate the equipment__________________________________
CAUTION : To prevent electric shock and risk of fire hazards.
DO NOT use power sources other than that specified.______
DO NOT expose this appliance to rain or moisture.000
This installation should be made by a qualified service person and should conform to all local codes.
Contents
Package Contents
3
Precautions
4
Camera Installation
5
Internal Components
7
Features
9
1
Operating Your Camera
11
SET UP
13
SET UP LENS
14
SHUTTER SPEED CONTROL
15
BACK LIGHT
19
AUTO GAIN (AGC)
20
WHITE BALANCE
21
REDUCE NOISE
23
INTENSIFIER
CAMERA TITLE
24
25
DAY/NIGHT/SYNC
27
MOTION DETECTION
29
PRIVACY
31
REVERSE
32
DETAIL
33
DEFAULT/RETURN
34
Troubleshooting
35
Specifications / Dimensions
37
Warranty
39
2
PACKAGE CONTENTS
•
Please make sure that the following items are included
in the package:
1 CVC-6246iHR Camera
2 Mounting Screws
1 Video test Connector
1 Power Adaptor Lead
Please leave this manual with the end-user for future
reference.
3
PRECAUTIONS
•
THIS DOME CAMERA SHOULD BE ONLY INSTALLED BY
QUALIFIED PERSONNEL
•
TO PREVENT A FIRE OR ELECTRICAL HAZARD PLEASE USE
PROPER POWER CABLE
•
THE DOME COVER SHOULD BE TREATED WITH CARE. DO
NOT CELAN THE COVER WITH AN ABRAISIVE CLEANING
MATERIAL - PLEASE USE A SOFT CLOTH OR TISSUE TO
CLEAN THE DOME COVER
•
THERE ARE NO USER-SERVICEABLE PARTS INSIDE. PLEASE
DO NOT DISASSEMBLE THIS CAMERA OTHER THAN TO
MAKE INITIAL ADJUSTMENTS
•
PLEASE USE A UL APPROVED REGULATED 24 VOLT AC OR
12 VOLT DC POWER SUPPLY
•
PLEASE USE APPROPRIATE LOW VOLTAGE POWER CABLE
TO PREVENT FIRE OR ELECTRICAL SHOCK
•
PLEASE INSURE THAT YOUR INSTALLATION AREA CAN
SUPPORT THE WEIGHT OF THE CAMERA
•
PLEASE HANDLE THIS CAMERA CAREFULLY:
- DON’T USE A STRONG OR ABRASIVE DETERGENT WHEN
CLEANING THE CAMERA.
- DO NOT EXPOSE THE CAMERA TO DIRECT SUN
4
CAMERA INSTALLATION
CONNECT POWER CABLE
1. WHEN USING 12 VOLTS DC (constant voltage 600 mA)
POWER INPUT:RED
CONNECT
CENTER:(+)
POWER SUPPLY
2. WHEN USING 24 VOLTS AC (40 Volt Amps)
-CONNECT ACCESSORY CABLE TO THE POWER JACK
AND CONNECT 24V AC TO THE LEAD
POWER
RED(+)
CONNECT
AC 24V
BLACK:(-)
POWER SUPPLY
3. CONNECT VIDEO CABLE
-CONNECT BNC CABLE TO THE BNC JACK.
YELLOW:VIDEO OUT
5
INTERNAL COMPONENTS
1. Mechanical
(2) Joy Stick
Controller
(1) DC Auto iris Lens
(2.8~11mm)
(1) DC AUTO-IRIS LENS
Adjust between TW (TELE  WIDE) to set the
angle (focal length) Set the focus by adjusting ∞N
NOTE: BOTH OF THE ABOVE ADJUSTMENTS GET LOCKED
INTO POSITION THROUGH THE USE OF "LOCKING HANDLES".
(2) JOY STICK
TO SET THE OSD (ON SCREEN DISPLAY) , PRESS THE JOY
STICK FOR ONE SECOND AND SET AS DESCRIBED
IN THE MANUAL
7
2. Joy Stick
Video Test
Terminal
UP
SET
RIGHT
LEFT
DOWN
Push the Joy stick for one second, and the OSD appears
on the screen. Move the Joy Stick up, down, left & right to
control the OSD functions.
8
Features
SLC
When the image is in front of strong background lighting,
your camera allows you to get a clear image.
INTENSIFIER
1/3 inch high density CCD and digital processor permit
high quality pictures to be captured in very low light conditions.
High Resolution
Horizontal resolution of 540 TV lines is
achieved by using a SONY Double Speed CCD with
410,000 pixels, yielding pictures with a high S/N ratio..
Motion Detection
Built in motion detector with adjustable areas of coverage will
flash a warning on the screen when motion is detected.
9
OSD
All camera functions are menu driven for easy use.
Dynamic Noise Reduction
The Intensifier camera has a DSP chip that can
remove image noise efficiently showing clean
images in low light conditions.
ELECTRONIC DAY/NIGHT
The Intensifier camera can show color pictures in all lighting
conditions, or you can have it automatically switch to a B/W
picture in low light conditions
MANUAL / AUTO IRIS LENS
The Intensifier camera will work with auto iris, manual iris and
fixed iris lenses.
10
Operating your camera
OSD Function
SETUP MENU
LENS TYPE
●DC ●MANUAL
SHUTTER TYPE
●OFF
●F/L
●MANUAL
WHITE BALANCE
●ATW ●AWC MANUAL●
SLC
●OFF
●LOW ●MIDDLE ●HIGH
AUTO GAIN
●OFF ●LOW ●MIDDLE ●HIGH
REDUCE NOISE
●OFF ●LOW ●MIDDLE ●HIGH
INTENSIFIER
●AUTO
●OFF
NEXT PAGE
●CAMERA TITLE ●DAY/NIGHT ●SYNC
●MOTION DET ●PRIVACY ●REVERSE
●DETAIL ●DEFAULT ●PAGE1
EXIT
11
Operating your camera – SETUP
1. Press the SET button (JOYSTICK) to access the SETUP mode.
SET UP menu is displayed on the monitor screen.
2. Select the desired feature using the UP or DOWN
button.
Each time you press the UP or DOWN button, the arrow
indicator moves up or down.
Move the arrow indicator to the desired feature item.
3. Change the status of the selected feature using the LEFT
or RIGHT button.
If you press the RIGHT or LEFT button, the status will change.
Press the button to get the desired feature.
4. When completed, move the arrow indicator to ‘EXIT" and
press the SET button.
Notes
You can access submenu using SET button.
For the mode with ‘---’, you may not access submenu.
13
Operating your camera – SETUP LENS
1) Setting up the LENS
Select the lens type by pressing the RIGHT button.
① On the SETUP menu screen, move the arrow indicator to the lens
using the UP or DOWN button.
② Select the desired feature using the LEFT or RIGHT button.
14
Operating your camera – SETUP LENS
▶When DC LENS selected, press SET button to control the
BRIGHTNESS.
15
2) Shutter status and speed control
You can control brightness of the screen by the shutter speed.
① Press the SET button to display the setup menu and move the arrow
indicator to ‘SHUTTER’ using the UP or DOWN button.
② Set ‘SHUTTER’ to the desired mode using the LEFT or RIGHT button.
▶ OFF : Deactivation
▶ FLK(1/100) : Flicker mode
16
Operating your camera – SETUP SPEED CONTROL. ②
▶MANUAL : When setting the shutter speed manually.
You can select speed from ‘1/60’ to ‘1/200,000’sec
17
▶ELC : You can control the BRIGHTNESS.
③When completed, press ‘SET’
Notes
Avoid pointing the camera directly at a fluorescent lamp
When the SHUTTER menu is set to FLK mode, the INTENSIFIER will not work.
18
Operating your camera – BACKLIGHT
3) SLC (Speco Light Compensation) - BACKLIGHT
A built-in SR chip provides intelligent light level control to overcome
severe Backlight conditions.
① Press the SET button to display the SETUP menu and move the arrow
indicator to ‘BACKLIGHT’ using the UP or DOWN button.
② SET ‘BACKLIGHT’ to the desired mode using the LEFT or RIGHT button.
▶OFF
▶LOW
▶MIDDLE
19
▶HIGH
4) AUTO GAIN CONTROL (AGC)
AGC allows a brighter picture in low light conditions. Higher GAIN level
will yield a brighter screen but you might notice an increase in noise.
① Press the SET button to display the SETUP menu and move the arrow
indicator to ‘AGC’ using the UP or DOWN button.
② SET ‘BACKLIGHT’ to the desired mode using the LEFT or RIGHT button.
▶OFF
▶LOW
▶MIDDLE
20
▶HIGH
Operating your camera – WHITE BALANCE
5) WHITE BALANCE
① Press the SET button to display the SETUP menu and move the arrow
indicator to ‘WHITE BALANCE’ using the UP or DOWN button.
② Set ‘WHITE BAL.’ to the desired mode using LEFT or RIGHT button.
▶ ATW (Auto Tracking White Balance)
: When color temperature is 2400~12000K, select this mode.
(ex. A fluorescent lamp, outdoor).
This is the best setting for most conditions.
▶ AWC (Auto White Balance Control)
: The white balance is automatically adjusted in a specific environment.
In order to obtain the best result, press the set button while the camera
focuses on white paper. If the environment including the light source is
changed, you have to adjust the white balance again.
21
▶MANUAL : To fine adjust, select the Manual mode. You can increase
or decrease the red or blue factor while monitoring the difference on the
screen. Set to ‘MANUAL’ mode and press the SET button. Increase or
decrease the value for RED(R-Gain) and BLUE(B-Gain), watching the color
of the picture, and press the SET button when you obtain the best color.
Notes
Proper White Balance may not be obtained under the following conditions
in these cases select the AWC mode.
When the scene contains mostly high color temperature object, such as
a blue sky or sunset.
When the scene is dim.
If your camera faces fluorescent lamp directly or is installed in the place
of the changing illumination.
22
Operating your camera – REDUCE NOISE
6) REDUCE NOISE (Dynamic Noise Reduction)
DNR reduces the noise on the screen.
① Press the SET button to display the SETUP menu and move the
arrow indicator to ‘DNR’ using the UP or DOWN button.
② SET ‘REDUCE NOISE’ to the desired mode using the LEFT
or RIGHT button.
▶ OFF : Deactivation
▶ LOW : Low reduction of noise
▶ MIDDLE : Middle reduction of noise
▶ HIGH : High reduction of noise
Notes
If you change the ‘GAIN’ menu from AGC-L to AGC-H
sensitivity is increased as well as noise on the screen.
When selected ‘GAIN’ menu OFF, DNR will not work.
23
Operating your camera – INTENSIFIER
7) INTENSIFIER
Allows you to get clear images under night or low light conditions
① Press the SET button to display the SETUP menu and move the
arrow indicator to ‘INTENSIFIER’ using the UP or DOWN button.
② SET ‘INTENSIFIER’ to the desired mode using the LEFT or RIGHT button.
▶ AUTO : When your camera is under night or low-lighting
level, select this mode. This mode allows the
camera to switch into B/W in low light conditions.
Notes
If you press SETUP button at ’AUTO’ menu, you can control the
lowlight action maximum magnifications.(X2~X128)
Increasing the amount of Intensification results in brighter pictures
Under low light conditions, and may increase image lag.
Increasing the amount of intensification may cause image noise
which is to be expected as a normal condition.
24
Operating your camera – CAMERA TITLE ①
8) NEXT PAGE
① Press the SET button to display the SETUP menu and move the
arrow indicator to ‘SENCE UP’ using the UP or DOWN button.
② SET ‘NEXT PAGE’ to the desired mode using the LEFT or RIGHT button.
(A) CAMERA TITLE
① Press the SET button to display the SETUP menu and move the arrow
indicator to ‘CAMERA ID’ using the UP or DOWN button.
② SET ‘ON’ using the LEFT or RIGHT button.
Notes
If the CAMERA ID feature is set to ‘OFF’, the name will not displayed
in the monitor.
25
Operating your camera – CAMERA TITLE ②
③ Press SET button to access the SETUP mode.
④ You can enter up to 15 characters.
a. Move the cursor to character-enter location by using the LEFT
or RIGHT button.
b. Select the desired character by using the UP or DOWN button.
c. Press SET button to confirm the blinking character. The first
character is saved and the cursor in the bottom of the screen
moves to the next position.
d. Repeat steps a, b and c until you create the full name you want.
e. Select the position at which the CAMERA ID will b located on
the screen.
-Move the cursor to ‘POS’ and press SET button.
-Select the position by using the 4-directional buttons, then press
the SET button to confirm the position.
f. When completed, move the cursor to ‘END’ and press SET button.
Notes
If you make a mistake while entering a name move the cursor “ CLR”.
Press “SET” button.
After erasing the character from right to left, correct the character again.
26
Operating your camera – COLOR / SYNC
B) COLOR
You can choose color and B/W mode electronically.
① Press the SET button to display the SETUP menu and move the
arrow indicator to ‘SENCE UP’ using the UP or DOWN button.
② SET ‘INTENSIFIER’ to the desired mode using the LEFT or RIGHT button.
▶ COLOR : The camera will always display a color picture
▶ AUTO : The camera will switch into B/W mode under
low light conditions.
Notes
OSD Key may not work for 3 seconds for the stable when COLOR/ BW mode
is changed
27
C) SYNC
Two SYNCHRONIZATION modes are available INTERNAL and
EXTERNAL LINE-LOCK
① Press the SET button to display the setup menu and move the arrow indicator
to ‘SYNC’ using the UP and DOWN button.
② SET to the desired mode using the LEFT or RIGHT button.
▶ INT : Internal synchronization
▶ L/L : If you choose ‘L/L’, you can adjust the desired phase.
- Press the SET button.
- You can adjust the desired phase from 0 to 270.
Notes
When it used in 24V AC power the L/L mode can be used.
In DC12V, the SYNC menu defaults to “ internal.
28
Operating your camera – MOTION DETECTION
D) Whenever your camera detects motion, THE WORDS “motion
detected’ will appear on the screen.
① Press the SET button to display the setup menu and move the arrow
indicator to ‘MOTION DET’ using the UP and DOWN button.
② SET ‘MOTION DET’ to the desired mode using the LEFT or RIGHT button.
▶OFF : Deactivation
▶ON : MOTION DET. Activated
- Press SET button.
- Move the arrow indicator to ‘AREA SET’ using UP and
DOWN button, and then press the SET button.
- Set the areas you want to observe.
29
Max.
Min.
30
Operating your camera – PRIVACY
E) PRIVACY
To mask an area that you want to be private.
① Press the SET button to display the setup menu and move the arrow
indicator to ‘PRIVACY’ using the UP and DOWN button.
② SET ‘PRIVACY’ to the desired mode using the LEFT or RIGHT button.
▶OFF : Deactivation
▶ON : PRIVACY mode activated
-Press the SET button.
-Move the arrow indicator to area you want to mask.
-Set ‘ON’ using LEFT or RIGHT button.
-Press the SET button and then set the area’s bounds
as for Motion detection
31
Operating your camera – REVERSE
F) REVERSE
① Press the SET button to display the setup menu and move the arrow
indicator to ‘REVERSE’ using the UP and DOWN button.
② SET ‘REVERSE’ to the desired mode using the LEFT or RIGHT button.
▶OFF : Deactivation
▶ON : Reverse the image RIGHT or LEFT.
32
Operating your camera – DETAIL
F) DETAIL
① Press the SET button to display the setup menu and move the arrow
indicator to ‘DETAIL’ using the UP and DOWN button.
② SET ‘DETAIL’ to the desired mode using the LEFT or RIGHT button.
▶OFF : Deactivation
▶ON : DETAIL control mode (level 0~31)
When the level is up, the sharpness will increase.
Control this level to get your best picture quality.
If the level is too high, you can get an unnatural image
with video noise.
33
Operating your camera – DEFAULT / PAGE 1
G) DEFAULT
: Use to reset your camera to FACTORY DEFAULT SETTING.
H) PAGE 1
: PAGE 1 : Save the setting of NEXT PAGE function, and then
move to SET UP menu.
34
Troubleshooting
If you have trouble operating your camera, refer to the following
Problem
Nothing appears on
the screen.
Solution
● Check that the power cord and line connection
between the camera and monitor are proper
● Check that you have properly connected VIDEO
cable the camera VIDEO output jack.
The image on the
screen is dim.
The image on the
screen is dark.
● Is lens stained with dirt? Clean your lens with
soft,
clean cloth.
● Set the monitor to proper condition.
● If the camera is exposed to too strong light
change the camera position.
● Adjust the lens’ focus properly.
● Adjust the contrast feature of the monitor.
● If you have an intermediate device, set the
75Ω/Hi-z properly.
The camera is not
working properly, and
the surface of the
camera is not.
● Check that you have properly connected
the camera to an appropriate power source.
MOTION DETECTION
function is not active.
● Have you set ‘MOTION DET.’ menu to off?
● Have you set ‘MD LEVEL’ to too how?
● Have you set ‘MD ARAEA’ properly
35
Problem
Solution
The color of the
picture is not
matched.
● Check that you have properly set the
‘ WHITE BALANCE ’ menu
The image on the
screen flickers.
● Is the camera facing to direct sunlight or fluorescent
lighting? Change the camera position.
L/L mode isn’t
able to be
selected.
● Have you connected your camera to DC power
source? Connect it to AC power source.
36
SPECIFICATIONS
ITEM
CVC-6246IHR
Power Source
DC 12V & AC 24v ( Dual Voltage )
Power Consumption
230mA(DC) / 3.8W(AC)
Image Sensor
1/3”, SONY SUPER HAD CCD,
Total Pixels
811(H) x 508(V) , 1/3” CCD
Effective Pixels
768(H) x 494(V) , 1/3” CCD
LENS TYPE
DC AUTO IRIS VAROFOCAL 2.8~11mm
Maximum Aperture Ratio
1 : 1.3 ~2.0
Scanning System
2 : 1 Interlaced 525 Lines / 60 Fields / 30 Frames
Synchronization
Internal / Line Lock selectable
Video Output
1.0V [p-p] NTSC Composite, 75Ω / BNC Connector
Resolution
540 TV Line
Gain Control
AGC-L, AGC-M, AGC-H, OFF selectable
Electric Shutter Speed
1/60 ~ 1/200,000 sec
INTENSIFIER
Built-in ( selectable limit ~ X128)
WHITE BALANCE
W-ATW / S-ATW / AWC /MANUAL
Min. Illumination
0.002Lux (intensifier) 0.3Lux (shutter)
S/N ( Y signal)
50dB (Weight On)
Reduction Noise
ON / LOW / MIDDLE / HIGH
Motion Detection
MD1 / MD2 / OFF
On Screen Display ( O.S.D )
Built - in
PRIVACY Function
ON / OFF (4 Programmable Zone)
Operational Temperature
-10℃ ~ +50℃ (14℉ ~122℉)
Operational Humidity
30% ~90% RH
37
410,000 pixels
DIMENSIONS
* SIDE VIEW
* TOP VIEW
38
WARRANTY
39
200 New Highway
Amityville, NY 11701
631-957-8700
www.specotech.com
VER. 070817
This manual is based on the date as shown in the right and specifications are subject to
Change without notice for quality improvement.