Download Hunter Engineering Quick Tread Specification Sheet

Quick Check Drive Thru with Quick Tread
Flush Mounted
Site Specifications
115/230v, 15 amp* 50/60 Hz 1 phƗ
Power Requirements
90-150 PSI (6.2-10.3 bar)
Air Supply Req. (IS Units)
Approximate Air
Consumption
25 SCFM @ 90 PSI
(648 Lpm @ 6.2 bar)
Substructure Specifications
Refer to Form 6905-T
Pedestal Location
36 - 96 in. (914 - 2438 mm) from QT1F
Product Specifications
3500 lb. (1588 kg) per wheel
Max. Wheel Weight
2 to 8 mph (3-13 km/h)
Test Entry Speed
Shipping Weight
Drive Thru Quick Check and Flush Mount Quick Tread
Installation
*
Quick Check Cabinet
290 lbs (132 kg)
Quick Check Drive Under
Sensor
316 lbs (143 kg)
Quick Tread
1723 lbs (455 kg)
Amperage shown is minimal circuit rating.
Ɨ
Isolated ground recommended.
OVERALL FOOTPRINT
15 ft.
RECOMMENDED
BAY WIDTH
QUICK TREAD COMMUNICATION CABLES (UP TO 75 ft.)
DISTANCE OF
LONGEST
WHEELBASE
VEHICLE
TO BE TESTED
(TYPICAL
165 in.)
51 in.
END OF BAY TO
FRONT WHEEL STOP:
TYPICAL 120 in.
MINIMUM 95 in.
108 in.-114 in.
(9 ft.- 9 ft. 6 in.)
93 in.
(7 ft. 9 in.)
4 in.
OPTIONAL
PEDESTAL
LOCATION
TYPICAL
RECOMMENDED
BAY LENGTH
28 ft. 4 in.
TO
26 ft. 3 in.
Continued on Page 2
For inspection information visit:
www.hunter.com/inspection
For general inquiries visit:
www.hunter.com
or call
800 448-6848
For local contact visit:
www.hunter.com/company/findrep.cfm
Form 6895-T, 05-15a
Copyright © 2015, Hunter Engineering Company
Quick Check Drive Thru with Quick Tread
Flush Mounted
QUICK CHECK DIMENSIONS
24 1/2 in.
67 1/4 in.
(5 ft. 7 1/4 in.)
16 1/4 in.
50 in.
45 1/4 in.
11 in.
32 in.
12 in.
23 1/2 in.
QUICK TREAD DIMENSIONS
PEDESTAL
26 in.
36 in.
26 in.
5 in. 14 7/8 in.
51 in.
96 in. (8 ft.) is the
maximum distance
between the middle of the
pedestal and nearest edge
of Quick Tread. Any
further will reduce max
vehicle test entry speed.
34 1/2 in.
5 in.
36 to 96 in.
(3 ft. to 8 ft.)
17 3/8 in.
93 in.
(7 ft. 9 in.)
PIT & CONDUIT SPECIFICATIONS
END VIEW
SIDE VIEW
QUICK TREAD:
HUNTER
SUPPLIED
Quick Tread’s 3 in.
underground conduit must
be routed to the pedestal
according to local codes. The
pedestal can be placed on
either side. Exact placement
of conduit will vary. Refer to
Form 6905-T.
QUICK TREAD
SUB-STRUCTURE:
CONTRACTOR
SUPPLIED
93 in.
51 in.
BAY FLOOR
8 in.
12 in.
(min.)
46.25 in.
88 in.
Form 6895-T, 05-15a
Copyright © 2015, Hunter Engineering Company