Download Hunter Engineering Quick Tread Specification Sheet

Quick Check Drive Under with Quick Tread
Flush Mounted
Site Specifications
115/230v, 15 amp* 50/60 Hz 1 phƗ
Power Requirements
90-150 PSI (6.2-10.3 bar)
Air Supply Req. (IS Units)
Approximate Air
Consumption
25 SCFM @ 90 PSI
(648 Lpm @ 6.2 bar)
Substructure Specifications
Refer to Form 6905-T
Pedestal Location
36 - 96 in. (914 - 2438 mm) from QT1F
Product Specifications
3500 lb. (1588 kg) per wheel
Max. Wheel Weight
2 to 8 mph (3-13 km/h)
Test Entry Speed
Shipping Weight
Drive Under Quick Check and Flush Mount Quick Tread
Installation
(shown with optional monitor)
*
Quick Check Cabinet
290 lbs (132 kg)
Quick Check Drive Under
Sensor
316 lbs (143 kg)
Quick Tread
1723 lbs (455 kg)
Amperage shown is minimal circuit rating.
Ɨ
Isolated ground recommended.
OVERALL FOOTPRINT
15 ft.
RECOMMENDED BAY
WIDTH
QUICK TREAD COMMUNICATION CABLES (UP TO 75 ft.)
165 in.
(ACCOMMODATES
VEHICLES WITH
MAXIMUM OF
165 in.
WHEELBASE.)
51 in.
END OF BAY
TO FRONT
WHEEL STOP:
120 in.
SENSOR
HEIGHT:
10 FT.
93 in.
(7 ft. 9 in.)
4 in.
OPTIONAL
PEDESTAL
LOCATION
RECOMMENDED
BAY LENGTH
28 ft. 4 in.
Continued on Page 2
For inspection information visit:
www.hunter.com/inspection
For general inquiries visit:
www.hunter.com
or call
800 448-6848
For local contact visit:
www.hunter.com/company/findrep.cfm
Form 6898-T, 05-15a
Copyright © 2015, Hunter Engineering Company
Quick Check Drive Under with Quick Tread
Flush Mounted
QUICK CHECK DIMENSIONS
135 in.
(11 ft. 3 in.)
15 in.
WITHOUT
OPTIONAL
MONITOR
18 in.
WITH
OPTIONAL
MONITOR
24 1/2 in.
SENSOR PROFILE
67 1/4 in.
(5 ft. 7 1/4 in.)
See 6429-T for
support structure
details. Mounting
plate dimensions
are provided to
aid fabrication.
16 1/4 in.
16 in.
WITHOUT
OPTIONAL
MONITOR
45 1/4 in.
It is recommended that a
low clearance warning be
suspended at the entrance
of Drive Under Quick
Check® bays.
22 in.
WITH
OPTIONAL
MONITOR
23 1/2 in.
32 in.
QUICK TREAD DIMENSIONS
PEDESTAL
26 in.
36 in.
26 in.
5 in.
14 7/8 in.
51 in.
96 in. (8 ft.) is the
maximum distance
between the middle of the
pedestal and nearest edge
of Quick Tread. Any
further will reduce max
vehicle test entry speed.
34 1/2 in.
5 in.
17 3/8 in.
36 to 96 in.
(3 ft. to 8 ft.)
93 in.
(7 ft. 9 in.)
PIT & CONDUIT SPECIFICATIONS
END VIEW
SIDE VIEW
QUICK TREAD:
HUNTER
SUPPLIED
Quick Tread’s 3 in. underground
conduit must be routed to the
pedestal according to local
codes. The pedestal can be
placed on either side. Exact
placement of conduit will vary.
Refer to Form 6905-T.
QUICK TREAD
SUB-STRUCTURE:
CONTRACTOR
SUPPLIED
93 in.
51 in.
BAY FLOOR
8 in.
12 in.
(min.)
46.25 in.
88 in.
Form 6898-T, 05-15a
Copyright © 2015, Hunter Engineering Company