Download Dell W-IAP103 CLI Reference Guide

Reference Guide
Dell Networking W-Series
Instant 6.4.0.2-4.1
Command-Line Interface
Copyright
© 2014 Aruba Networks, Inc. Aruba Networks trademarks include
, Aruba Networks®, Aruba
®
Wireless Networks , the registered Aruba the Mobile Edge Company logo, and Aruba Mobility Management
System®. Dell™, the DELL™ logo, and PowerConnect™ are trademarks of Dell Inc.
All rights reserved. Specifications in this manual are subject to change without notice.
Originated in the USA. All other trademarks are the property of their respective owners.
Open Source Code
Certain Aruba products include Open Source software code developed by third parties, including software code
subject to the GNU General Public License (GPL), GNU Lesser General Public License (LGPL), or other Open
Source Licenses. Includes software from Litech Systems Design. The IF-MAP client library copyright 2011 Infoblox,
Inc. All rights reserved. This product includes software developed by Lars Fenneberg, et al. The Open Source code
used can be found at this site:
http://www.arubanetworks.com/open_source
Legal Notice
The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate
other vendors’ VPN client devices constitutes complete acceptance of liability by that individual or corporation for
this action and indemnifies, in full, Aruba Networks, Inc. from any and all legal actions that might be taken against it
with respect to infringement of copyright on behalf of those vendors.
0511587-01 | June 2014
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Chapter 1
About this Guide
This document describes the Dell Networking W-Series Instant command syntax and provides the following
information for each command:
l
Command Syntax—The complete syntax of the command.
l
Description—A brief description of the command.
l
Syntax—A description of the command parameters, the applicable ranges and default values, if any.
l
Usage Guidelines—Information to help you use the command, including prerequisites, prohibitions, and related
commands.
l
Example—An example of how to use the command.
l
Command History—The version of Instant in which the command was first introduced.
l
Command Information—This table describes command modes and platforms for which this command is
applicable.
The commands are listed in alphabetical order.
Intended Audience
This guide is intended for customers who configure and use Dell Networking W-Series Instant Access Point (WIAP).
Related Documents
In addition to this document, the Dell W-IAP product documentation includes the following:
l
Dell Networking W-Series Instant Access Point Installation Guides
l
Dell Networking W-Series Instant 6.4.0.2-4.1 Quick Start Guide
l
Dell Networking W-Series Instant 6.4.0.2-4.1 User Guide
l
Dell Networking W-Series Instant 6.4.0.2-4.1 MIB Reference Guide
l
Dell Networking W-Series Instant 6.4.0.2-4.1 Syslog Messages Reference Guide
l
Dell Networking W-Series Instant 6.4.0.2-4.1 Release Notes
Conventions
The following conventions are used throughout this document to emphasize important concepts:
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
About this Guide | 3
Table 1: Typographical Conventions
Type Style
Description
Italics
This style is used for emphasizing important terms and to mark
the titles of books.
Boldface
This style is used for command names and parameter options
when mentioned in the text.
Commands
This fixed-width font depicts command syntax and examples of
commands and command output.
<angle brackets>
In the command syntax, text within angle brackets represents
items that you should replace with information appropriate to
your specific situation.
For example, ping <ipaddr>
In this example, you would type “ping” at the system prompt
exactly as shown, followed by the IP address of the system to
which ICMP echo packets are to be sent. Do not type the angle
brackets.
[square brackets]
In the command syntax, items enclosed in brackets are
optional. Do not type the brackets.
{Item_A|Item_B}
In the command examples, single items within curled braces
and separated by a vertical bar represent the available
choices. Enter only one choice. Do not type the braces or bars.
{ap-name <ap-name>}|{ipaddr <ipaddr>}
Two items within curled braces indicate that both parameters
must be entered together. If two or more sets of curled braces
are separated by a vertical bar, like in the example to the left,
enter only one choice. Do not type the braces or bars.
The following informational icons are used throughout this guide:
Indicates helpful suggestions, pertinent information, and important things to remember.
Indicates a risk of damage to your hardware or loss of data.
Indicates a risk of personal injury or death.
Contacting Dell
Table 2: Support Information
Support
Main Website
dell.com
Contact Information
dell.com/contactdell
Support Website
dell.com/support
Documentation Website
dell.com/support/manuals
4 | About this Guide
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
What is New in Instant 6.4.0.2-4.1
This section lists the new and modified commands in the Instant 6.4.0.2-4.1 release.
New Commands
The following commands are added in the Instant 6.4.0.2-4.1 release:
Table 3: New Commands in 6.4.0.2-4.1
Command
Description
console
Allows you to enable or disable access to the W-IAP console.
dpi
Enables deep packet inspection (DPI) support and allows you to configure DPI for wired or
wireless network users.
inbound-firewall
Allows you to configure inbound firewall rules.
mgmt-accounting
Enables accounting privileges on TACACS+ servers for management users in Instant.
rft
Allows you to run tests for RF troubleshooting.
NOTE: In this release, this command is not available in W-IAP224/225, and W-IAP274/275
platforms.
show consolesettings
Displays if the console access is enabled or disabled on a W-IAP.
show dhcp subnets
Displays subnet details and gateway IP address for the distributed L2 and L3 networks.
show dpi
Displays the DPI configuration details.
show dpi-stats
Displays DPI statistics for application, application category, web category and web reputation
parameters.
show ap dot11kbeacon-report
Displays the beacon report details for the 802.11k clients of a W-IAP.
show ap dot11knbrs
Displays neighbors for the 802.11k clients of a W-IAP.
show inboundfirewall-rules
Displays the inbound firewall rule details.
show rft trans-id
Displays transaction IDs for the RF test profiles.
show rft profile
Displays the profile parameters for the RF tests.
show xml-apiserver
Displays the XML API server configuration details
wlan tacacs-server
Configures a TACACS+ server to authenticate management users in Instant.
xml-api-server
Integrates an XML API Interface with a W-IAP.
zonename
Configures zone settings on a W-IAP.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
About this Guide | 5
Modified Commands
The following commands are modified in the Instant 6.4.0.2-4.1 release:
Table 4: Modified Commands in 6.4.0.2-4.1
Command
Description
airgroup
This command now allows you to enable DLNA and mDNS (Bonjour services) support on a
W-IAP for the AirGroup enabled clients.
airgroupservice
This command now allows you to configure services such as Chromecast, DLNA media,
and DLNA print services.
ip dhcp
This command now allows you to enable or disable split tunnel for Centralized, L2 clients .
l2tpv3 session
This command now allows you enable default l2 specific sublayer for the L2TPV3 sessions.
show airgroup
This command now includes the DLNA and MDNS options to filter the output based on the
DLNA and Bonjour services (mDNS) configuration status.
show airgroupservice
The output of this command now displays the disallowed roles and VLANs for the
mDNS and DLNA services.
show access-rule
The output of this command displays the access rules created for DPI.
show access-rule-all
show auth-survivability
The debug-log option is added to the command syntax. On running the show authsurvivability debug-log command, the logs for troubleshooting the authentication
survivability are displayed.
show dhcps config
The output of this command now displays split-tunnel status for centralized,L2 and and DNS
caching status for local or local,l2 profiles.
show vpn
This command now displays the IAP-VPN retry counter details when the tunnels keyword is
used.
wlan access-rule
This command now allows you to configure access rules for deep packet inspection. The
rule command allows you to create access rules to allow or deny access to certain
application, application categories, website categories, and URLs based on security rating.
In the current release, you can also configure inbound firewall rules based on source
subnet.
wlan ssid-profile
This command now allows you to configure AP zone, WMM DSCP traffic mapping, backup
authentication server with termination enabled, and enable fast roaming features such as
802.11k and 802.11v. The command also allows you to disable bridging and routing traffic
between the clients connected to the same SSID.
arm
The maximum threshold value of Client Match has been increased to 255. The previous
maximum threshold limit was 20.
6 | About this Guide
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Chapter 1
Instant CLI
Instant supports the use of Command Line Interface (CLI) for scripting purposes. You can access the Instant CLI
through a Secure Shell (SSH).
To enable the SSH access to the Instant CLI:
1. From the Instant UI, navigate to System > Show advanced options.
2. Select Enabled from the Terminal access drop-down list.
3. Click OK.
Connecting to a CLI Session
On connecting to a CLI session, the system displays its host name followed by the login prompt. Use the
administrator credentials to start a CLI session. For example:
(Instant AP)
User: admin
Password: *****
If the login is successful, the privileged command mode is enabled and a command prompt is displayed. For
example:
(Instant AP)#
The privileged mode provides access to show, clear, ping, traceroute, and commit commands. The configuration
commands are available in the configuration (config) mode. To move from privileged mode to the configuration mode,
enter the following command at the command prompt:
(Instant AP)# configure terminal
The configure terminal command allows you to enter the basic configuration mode and the command prompt is
displayed as follows:
(Instant AP)(config)#
The Instant CLI allows CLI scripting in several other sub-command modes to allow the users to configure individual
interfaces, SSIDs, access rules, and security settings.
You can use the question mark (?) to view the commands available in a privileged mode, configuration mode, or submode.
Although automatic completion is supported for some commands such as configure terminal, the complete exit
and end commands must be entered at command prompt for successful execution.
Applying Configuration Changes
Each command processed by the Virtual Controller is applied on all the slave W-IAPs in a cluster. When you make
configuration changes on a master W-IAP in the CLI, all associated W-IAPs in the cluster inherit these changes and
subsequently update their configurations. The changes configured in a CLI session are saved in the CLI context.
The CLI does not support the configuration data exceeding the 4K buffer size in a CLI session: therefore, it is
recommended that you configure fewer changes at a time and apply the changes at regular intervals.
To apply and save the configuration changes at regular intervals, use the following command in the privileged mode:
(Instant AP)# commit apply
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Instant CLI | 7
To apply the configuration changes to the cluster, without saving the configuration, use the following command in the
privileged mode:
(Instant AP)# commit apply no-save
To view the changes that are yet to be applied, use the following command in the privileged mode:
(Instant AP)# show uncommitted-config
To revert to the earlier configuration, use the following command in the privileged mode.
(Instant AP)# commit revert
Example:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# rf dot11a-radio-profile
AP)(RF dot11a Radio Profile)# beacon-interval 200
AP)(RF dot11a Radio Profile)# no legacy-mode
AP)(RF dot11a Radio Profile)# dot11h
AP)(RF dot11a Radio Profile)# interference-immunity 3
AP)(RF dot11a Radio Profile)# csa-count 2
AP)(RF dot11a Radio Profile)# spectrum-monitor
AP)(RF dot11a Radio Profile)# end
(Instant AP)# show uncommitted-config
rf dot11a-radio-profile
no legacy-mode
beacon-interval 200
no dot11h
interference-immunity 3
csa-count 1
no spectrum-monitor
Instant Access Point# commit apply
Configuration Sub-modes
Some commands in configuration mode allow you to enter into a sub-mode to configure the commands specific to
that mode. When you are in a configuration sub-mode, the command prompt changes to indicate the current submode.
You can exit a sub-command mode and return to the basic configuration mode or the privileged Exec (enable) mode
at any time by executing the exit or end command.
Deleting Configuration Settings
Use the no command to delete or negate previously-entered configurations or parameters.
l
To view a list of no commands, type no at the prompt in the relevant mode or sub-mode followed by the question
mark. For example:
(Instant AP)(config) # no?
l
To delete a configuration, use the no form of a configuration command. For example, the following command
removes a configured user role:
(Instant AP)(config) # no user <username>
l
To negate a specific configured parameter, use the no parameter within the command. For example, the following
command deletes the PPPoE user configuration settings:
(Instant AP)(config) # pppoe-uplink-profile
(Instant AP)(pppoe_uplink_profile)# no pppoe-username
8 | Instant CLI
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Using Sequence Sensitive Commands
The Instant CLI does not support positioning or precedence of sequence-sensitive commands. Therefore, it is
recommended that you remove the existing configuration before adding or modifying the configuration details for
sequence-sensitive commands. You can either delete an existing profile or remove a specific configuration by using
the no… commands.
The following table lists the sequence-sensitive commands and the corresponding no command to remove the
configuration.
Table 5: Sequence-Sensitive Commands
Sequence-Sensitive Command
Corresponding no command
opendns <username <password>
no opendns
rule <dest> <mask> <match> <protocol> <start-port>
<end-port> {permit |deny | src-nat | dst-nat {<IPaddress> <port>| <port>}}[<option1…option9>]
no rule <dest> <:mask> <match>
<protocol> <start-port> <end-port>
{permit | deny | src-nat | dst-nat}
mgmt-auth-server <auth-profile-name>
no mgmt-auth-server <auth-profilename>
set-role <attribute>{{equals| not-equals| startswith| ends-with| contains} <operator> <role>| valueof}
no set-role <attribute>{{equals|
not-equals| starts-with| ends-with|
contains} <operator>| value-of}
no set-role
set-vlan <attribute>{{equals| not-equals| startswith| ends-with| contains} <operator> <VLAN-ID>|
value-of}
no set-vlan <attribute>{{equals|
not-equals| starts-with| ends-with|
contains} <operator>| value-of}
no set-vlan
auth-server <name>
no auth-server <name>
Saving Configuration Changes
The running-config holds the current W-IAP configuration, including all pending changes which are yet to be saved.
To view the running-config of a W-IAP, use the following command:
(Instant AP) # show running-config
When you make configuration changes through the CLI, the changes affect the current running configuration only. To
save your configuration changes, use the following command in the privileged Exec mode:
(Instant AP)# write memory
Commands that Reset the W-IAP
If you use the CLI to modify a currently provisioned radio profile, the changes take place immediately. A reboot of the
W-IAP is not required to apply the configuration changes. Certain commands, however, automatically force W-IAP
to reboot. Verify the current network loads and conditions before executing the commands that enforce a reboot of
the W-IAP, as they may cause a momentary disruption in service as the unit resets.
The reload command resets a W-IAP.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Instant CLI | 9
Command Line Editing
The system records your most recently entered commands. You can review the history of your actions, or reissue a
recent command easily, without having to retype it.
To view items in the command history, use the up arrow key to move back through the list and the down arrow key to
move forward. To reissue a specific command, press Enter when the command appears in the command history.
You can also use the command line editing feature to make changes to the command prior to entering it. The
command line editing feature allows you to make corrections or changes to a command without retyping. The
following table lists the editing controls. To use key shortcuts, press and hold the Ctrl button while you press a letter
key.
Table 6: Line Editing Keys
Key
Effect
Description
Ctrl A
Home
Move the cursor to the beginning of the line.
Ctrl B or the
left arrow
Back
Move the cursor one character left.
Ctrl D
Delete Right
Delete the character to the right of the cursor.
Ctrl E
End
Move the cursor to the end of the line.
Ctrl F or the
right arrow
Forward
Move the cursor one character right.
Ctrl K
Delete Right
Delete all characters to the right of the cursor.
Ctrl N or the
down arrow
Next
Display the next command in the command
history.
Ctrl P or
up arrow
Previous
Display the previous command in the command
history.
Ctrl T
Transpose
Swap the character to the left of the cursor with
the character to the right of the cursor.
Ctrl U
Clear
Clear the line.
Ctrl W
Delete Word
Delete the characters from the cursor up to and
including the first space encountered.
Ctrl X
Delete Left
Delete all characters to the left of the cursor.
10 | Instant CLI
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Specifying Addresses and Identifiers in Commands
This section describes addresses and other identifiers that you can reference in CLI commands.
Table 7: Addresses and Identifiers
Address/Identifier
Description
IP address
For any command that requires entry of an IP address to specify a network entity,
use IPv4 network address format in the conventional dotted decimal notation (for
example, 192.0.2.1).
Netmask address
For subnet addresses, specify a subnet mask in dotted decimal notation (for
example, 255.255.255.0).
Media Access Control
(MAC) address
For any command that requires entry of a device’s hardware address, use the
hexadecimal format (for example, 00:05:4e:50:14:aa).
Service Set Identifier
(SSID)
A unique character string (sometimes referred to as a network name), consisting
of no more than 32 characters. The SSID is case-sensitive (for example, WLAN01).
Basic Service Set
Identifier (BSSID)
This entry is the unique hard-wireless MAC address of the AP. A unique BSSID
applies to each frequency— 802.11a and 802.11g—used from the AP. Use the
same format as for a MAC address.
Extended Service Set
Identifier (ESSID)
Typically the unique logical name of a wireless network. If the ESSID includes
spaces, enclose the name in quotation marks.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Instant CLI | 11
aaa test-server
aaa test-server <servername> <username>
Description
This command tests a configured authentication server.
Syntax
Parameter
Description
<servername>
Allows you to specify the authentication server for which the authentication test
is run.
<username>
Allows you to specify the user name for which the authentication test is run.
Usage Guidelines
Use this command to view the CPU load for application and system processes. This command allows you to verify
a configured RADIUS authentication server or the internal database. You can use this command to check for an “out
of service” RADIUS server.
Example
The following example shows the output of the aaa test-server command:
Authentication is successful
Command History
Version
Description
Dell Networking WSeries Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
12 | aaa test-server
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
a-channel
a-channel <channel> <tx-power>
Description
This command configures 5 GHz radio channels for a specific W-IAP.
Syntax
Parameter
Description
Range
<channel>
Configures the specified 5 GHz channel.
The valid channels for a band
are determined by the AP
regulatory domain.
<tx-power>
Configures the specified transmission
power values.
0-127 dBm
Usage Guidelines
Use this command to configure radio channels for the 5 GHz band for a specific W-IAP.
Example
The following example configures the 5 GHz radio channel:
(Instant AP)# a-channel 44 18
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
a-channel | 13
a-external-antenna
a-external-antenna <gain>
Description
This command configures external antenna connectors for a W-IAP.
Syntax
Parameter
Description
Range
<gain>
Configures the antenna gain. You can configure a gain value
in dBi for the following types of antenna:
Diploe/Omni - 6
l
l
l
Dipole/Omni
Panel
Sector
Panel -14
Sector - 14
Usage Guidelines
If your W-IAP has external antenna connectors, you need to configure the transmit power of the system. The
configuration must ensure that the system’s Equivalent Isotropically Radiated Power (EIRP) is in compliance with
the limit specified by the regulatory authority of the country in which the W-IAP is deployed. You can also measure or
calculate additional attenuation between the device and antenna before configuring the antenna gain. To know if your
AP device supports external antenna connectors, see the Install Guide that is shipped along with the AP device.
EIRP and Antenna Gain
The following formula can be used to calculate the EIRP limit related RF power based on selected antennas
(antenna gain) and feeder (Coaxial Cable loss):
EIRP = Tx RF Power (dBm)+GA (dB) - FL (dB)
The following table describes this formula:
Table 8: Formula Variable Definitions
Formula Element
Description
EIRP
Limit specific for each country of deployment
Tx RF Power
RF power measured at RF connector of the unit
GA
Antenna gain
FL
Feeder loss
For information on antenna gain recommended by the manufacturer, see dell.com/support.
Example
The following example configures external antenna connectors for the W-IAP with the 5 GHz radio band.
(Instant AP)# a-external-antenna 14
14 | a-external-antenna
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
a-external-antenna | 15
aeroscout-rtls
aeroscout-rtls <IP-address> <Port> [include-unassoc-sta]
no...
Description
This command configures the Aeroscout Real-Time Asset Location Server (RTLS) settings for Instant and sends the
Radio-frequency identification (RFID) tag information to an Aeroscout RTLS server.
Syntax
Command/Parameter
Description
Default
<IP-address>
IP address of the Aeroscout RTLS server to which the
location reports are sent.
—
<Port>
Port number of the Aeroscout RTLS server to which the
location reports are sent..
—
include-unassoc-stas
Includes the client stations not associated to any W-IAP
when mobile unit reports are sent to the Aeroscout
RTLS server.
Disabled
no
Removes the Aeroscout RTLS configuration.
—
Usage Guidelines
This command allows you to integrate Aeroscout RTLS server with Instant by specifying the IP address and port
number of the Aeroscout RTLS server. When enabled, the RFID tag information for the stations associated with a
W-IAP are sent to the AeroScout RTLS. You can also send the RFID tag information for the stations that are not
associated with any W-IAP.
Example
The following example configures the Aeroscout RTLS server:
(Instant AP)(config)# aeroscout-rtls 192.0.2.2 3030 include-unassoc-sta
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
Command was introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
16 | aeroscout-rtls
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
airgroup
airgroup
cppm enforce-registration
cppm-query-interval <interval>
cppm-server <server-name>
disable
enable [dlna-only| mdns-only]
enable-guest-multicast
multi-swarm
no…
Description
This command configures the AirGroup settings on a W-IAP.
Syntax
Parameter
Description
cppm enforce-registration
Enforces the discovery of the CPPM
registered devices. When enabled,
only devices registered with CPPM
will be discovered by Bonjour® or
DLNA devices, based on the CPPM
policy configured.
cppm-query-interval
<interval>
Configures a time interval at which
Instant sends a query to ClearPass
Policy Manager for mapping the
access privileges of each device to the
available services.
cppm-server <server-name>
Range
Default
—
Enabled
1-24
10 hours
Configures the ClearPass Policy
Manager server information for
AirGroup policy.
—
—
disable
Disables the AirGroup feature.
—
—
enable [dlna-only| mdns-only]
Enables the mDNS or DLNA or both.
—
—
—
—
When dlna-only command is executed
with enable, the DLNA support is
enabled for AirGroup enabled
devices.
When mdns-only command is
executed with enable, the Bonjour
support is enabled for AirGroup
enabled devices.
enable-guest-multicast
Allows the users to use the Bonjour or
DLNA services enabled in a guest
VLAN. When enabled, the Bonjour or
DLNA devices will be visible only in
the guest VLAN and AirGroup will not
discover or enforce policies in guest
VLAN.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
airgroup | 17
Parameter
Description
Range
Default
multi-swarm
Enables inter cluster mobility. When
enabled, the W-IAP shares the mDNS
database information with the other
clusters. The AirGroup records in the
Virtual Controller can be shared with
all the Virtual Controllers specified for
L3 Mobility.
—
Disabled
no…
Removes the specified configuration
parameter.
—
—
Usage Guidelines
Use this command to configure the AirGroup, the availability of the AirGroup services, and ClearPass Policy
Manager (CPPM) servers.
Example
The following example configures an AirGroup profile:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# airgroup
AP)(airgroup)# enable
AP)(airgroup)# cppm enforce-registration
AP)(airgroup)# cppm-server Test
AP)(airgroup)# cppm-query-interval 10
AP)(airgroup)# enable-guest-multicast
AP)(airgroup)# multi-swarm
AP)(airgroup)# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.4.0.24.1
This command is modified.
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
18 | airgroup
W-IAP Platform
Command Mode
All platforms
Configuration mode and AirGroup configuration sub-mode.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
airgroupservice
airgroupservice <airgroupservice>
description <description>
disable
disallow-role <role>
disallow-vlan <VLAN-ID>
enable
id <AirGroupservice-ID>
no…
Description
This command configures the availability of AirGroup services for the W-IAP clients.
Syntax
Parameter
Description
<airgroupservice>
Specifies the AirGroup service to configure.
Default
—
The following pre-configured services are available for
W-IAP clients:
l AirPlay™— Apple® AirPlay allows wireless
streaming of music, video, and slideshows from
your iOS device to Apple TV® and other devices
that support the AirPlay feature.
l AirPrint™— Apple® AirPrint allows you to print from
an iPad®, iPhone®, or iPod® Touch directly to any
AirPrint compatible printers.
l iTunes— iTunes service is used by iTunes Wi-Fi
sync and iTunes home-sharing applications across
all Apple® devices.
l RemoteMgmt— Use this service for remote login,
remote management, and FTP utilities on Apple®
devices.
l Sharing— Applications such as disk sharing and file
sharing, use the service ID that are part of this
service on one or more Apple® devices.
l Chat— The iChat® (Instant Messenger) application
on Apple® devices uses this service.
l ChromeCast—ChromeCast service allows you to
use a ChromeCast device to play audio or video
content on a high definition television by streaming
content through Wi-Fi from the Internet or local
network.
l DLNA Media—Applications such as Windows Media
Player use this service to browse and play media
content on a remote device.
l DLNA Print—This service is used by printers that
support DLNA.
You can allow all services or add custom services. Up
to 10 services can be configured on a W-IAP.
description <description>
Adds a description to the AirGroup service profile.
—
disable
Disables AirGroup services for the profile.
—
disallow-role <role>
Restricts the user roles specified for role from
accessing the AirGroup service.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Disabled
airgroupservice | 19
Parameter
Description
Default
disallow-vlan <VLAN-ID>
Restricts the AirGroup servers connected on the
specified VLANs from being discovered.
enable
Enables the AirGroup service for the profile.
—
id <airgroupserviceid>
Allows you to specify the AirGroup service ID
corresponding to the service that you are trying to
configure.
—
Disabled
NOTE: The service IDs cannot be added for the preconfigured services.
Removes the AirGroup service configuration.
no…
—
Usage Guidelines
Use this command to enforce AirGroup service policies and define the availability of a services for an AirGroup
profile. When configuring AirGroup service for an AirGroup profile, you can also restrict specific user roles and
VLANs from availing the AirGroup services.
Example
The following example configures AirGroup services:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# airgroupservice AirPlay
AP)(airgroup-service)# description AirPlay Service
AP)(airgroup-service)# disallow-role guest
AP)(airgroup-service)# disallow-vlan 200
AP)(airgroup-service)# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.4.0.24.1
This command is modified.
Dell Networking W-Series Instant 6.3.1.14.0
This command is modified.
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and AirGroup services configuration submode.
20 | airgroupservice
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
airwave-rtls
airwave-rtls <IP-address> <Port> <key> <frequency> [include-unassoc-sta]
no…
Description
This command integrates W-AirWave Real-Time Asset Location Server (RTLS) settings for Instant and sends the
Radio-frequency identification (RFID) tag information to a W-AirWave RTLS server with the RTLS feed to accurately
locate the wireless clients.
Syntax
Command/Parameter
Description
Default
<IP-address>
Configures the IP address of the W-AirWave RTLS
server.
—
<Port>
Configures the port for the W-AirWave RTLS server.
—
<key>
Configures key for service authorization.
—
<frequency>
Configures the frequency at which packets are sent to
the RTLS server in seconds.
5
include-unassoc-sta
When enabled, this option sends mobile unit reports to
the W-AirWave RTLS server for the client stations that
are not associated to any W-IAP (unassociated
stations).
Disabled
no…
Removes the specified configuration parameter.
—
Usage Guidelines
Use this command to send the RFID tag information to W-AirWave RTLS. Specify the IP address and port number
of the W-AirWave server, to which the location reports must be sent. You can also send reports of the unassociated
clients to the RTLS server for tracking purposes.
Example
The following command enables W-AirWave RTLS:
(Instant AP)(config) # airwave-rtls ams-ip 192.0.2.3 3030 pass@1234 5 include-unassoc-sta
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
airwave-rtls | 21
ale-report-interval
ale-report-interval <seconds>
no…
Description
This command configures the interval at which a W-IAP sends data to the Analytics and Location Engine (ALE)
server.
Syntax
Command/Parameter
Description
Range
Default
ale-report-interval
<seconds>
Configures an interval at which the Virtual
Controller can report the W-IAP and client
details to the ALE server.
6–60 seconds
30
no…
Removes the specified configuration
parameter.
—
—
Usage Guidelines
Use this command to specify an interval for W-IAP and ALE server communication.
Example
The following example configures the ALE server details:
(Instant AP)(config)# ale-report-interval 60
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.1-4.0
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
22 | ale-report-interval
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
ale-server
ale-server <server>
no…
Description
This command configures Analytics and Location Engine (ALE) server details for W-IAP integration with ALE.
Syntax
Command/Parameter
Description
ale-server <server>
Allows you to specify the Fully Qualified Domain Name (FQDN) or IP
address of the ALE server.
no…
Removes the specified configuration parameter.
Usage Guidelines
Use this command to enable a W-IAP for ALE support.
Example
The following example configures the ALE server details:
(Instant AP)(config)# ale-server AleServer1
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.1-4.0
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
ale-server | 23
alg
alg
sccp-disable
sip-disable
vocera-disable
no…
Description
This command allows you to modify the configuration settings for Application Layer Gateway (ALG) protocols
enabled on a W-IAP. An application-level gateway consists of a security component that augments a firewall or NAT
used in a network.
Syntax
Command/Parameter
Description
Default
sccp-disable
Disables the Skinny Call Control Protocol (SCCP).
Enabled
sip-disable
Disables the Session Initiation Protocol (SIP) for VOIP
and other text and multimedia sessions.
Enabled
vocera-disable
Disables the VOCERA protocol.
Enabled
no…
Removes the specified configuration parameter.
—
Usage Guidelines
Use this command to functions such as SIP, Vocera, and Cisco Skinny protocols for ALG.
Example
The following example configures the ALG protocols:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# alg
AP)(ALG)# sccp-disable
AP)(ALG)# no sip-disable
AP)(ALG)# no vocera-disable
AP)(ALG)# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Command Information
24 | alg
W-IAP Platform
Command Mode
All platforms
Configuration mode and ALG configuration sub-mode.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
allow-new-aps
allow-new-aps
no…
Description
This command allows the new access points to join the W-IAP cluster.
Syntax
Command/Parameter
Description
allow-new-aps
Allows new access points in the domain.
no
Removes the specified configuration parameter.
Usage Guidelines
Use this command to allow the new access points to join the W-IAP cluster.
Example
The following command allows the new W-IAPs to join the cluster.
(Instant AP)(config)# allow-new-aps
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
allow-new-aps | 25
allowed-ap
allowed-ap <MAC-address>
no…
Description
This command allows an AP to join the W-IAP cluster.
Syntax
Command/Parameter
Description
allowed-ap <MAC-address>
Specifies the MAC address of the W-IAP that is allowed to join the
cluster.
no…
Removes the specified configuration parameter.
Usage Guidelines
Use this command to allow a W-IAP to join the cluster.
Example
The following command configures an allowed W-IAP:
(Instant AP)(config)# allowed-ap 01:23:45:67:89:AB
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
26 | allowed-ap
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
ams-backup-ip
ams-backup-ip <IP-address or domain name>
no…
Description
This command adds the IP address or domain name of the backup W-AirWave Management server.
Syntax
Parameter
Description
<IP-address or domain
name>
Configures the IP address or domain name of the secondary W-AirWave
Management Server.
no…
Removes the specified configuration parameter.
Usage Guidelines
Use this command to add the IP address or domain name of the backup W-AirWave Management Server. The
backup server provides connectivity when the W-AirWave primary server is down. If the W-IAP cannot send data to
the primary server, the Virtual Controller switches to the backup server automatically.
Example
The following command configures a W-AirWave backup server.
(Instant AP)(config)# ams-backup-ip 192.0.2.1
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
ams-backup-ip | 27
ams-identity
ams-identity <Name>
Description
This command uniquely identifies the group of W-IAPs managed or monitored by the W-AirWave Management
console. The name can be a location, vendor, department, or any other identifier.
Syntax
Parameter
Description
ams-identity <Name>
Configures a name that uniquely identifies the W-IAP on the WAirWave Management server. The name defined for this command
will be displayed under the Groups tab in the W-AirWave user
interface.
Usage Guidelines
Use this command to assign an identity for the W-IAPs monitored or managed by the W-AirWave Management
Server.
Example
The following command configures a W-AirWave identifier:
(Instant AP)(config)# ams-identity dell
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
28 | ams-identity
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
ams-ip
ams-ip <IP-address or domain name>
no…
Description
This command configures the IP address or domain name of the W-AirWave Management console for a W-IAP.
Syntax
Parameter
Description
<IP-address or domain name>
Configures the IP address or domain name of anW-AirWave
Management server for a W-IAP.
Usage Guidelines
Use this command to configure the IP address or domain name of the AMS console for a W-IAP.
Example
The following command configures the W-AirWave Server.
(Instant AP)(config)# ams-ip 192.0.1.2
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
ams-ip | 29
ams-key
ams-key <key>
no…
Description
This command assigns a shared key for service authorization.
Syntax
Parameter
Description
<key>
Authorizes the first Virtual Controller to communicate with the W-AirWave
server.
no…
Removes the specified configuration parameter.
Usage Guidelines
Use this command to assign a shared key for service authorization. This shared key is used for configuring the first
AP in the W-IAP network.
Example
The following command configures the shared key for the W-AirWave server.
(Instant AP)(config)# ams-key key@789
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Command Information
30 | ams-key
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
apply
apply {cplogo-install| cplogo-uninstall| debug-command| delta-config}
Description
This command is used to save or apply the configuration settings on the W-IAP.
Syntax
Parameter
Description
cplogo-install
Installs the Captive Portal logo on the W-IAP.
cplogo-uninstall
Uninstalls the Captive Portal logo on the W-IAP.
debug-command
Applies the configuration settings from the debug command.
delta-config
Applies the configuration settings from the delta-config command.
Usage Guidelines
Use this command to apply the current configuration settings on the W-IAP.
Example
The following example installs the captive portal logo on a W-IAP.
(Instant AP)(config)# apply cplogo-inistall http://cp.logo.com
The following example uninstalls the captive portal logo on a W-IAP.
(Instant AP)(config)# apply cplogo-inistall http://cp.logo.com
Command History
Version
Description
Dell Networking W-Series Instant 6.4.0.2-4.1
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
apply | 31
arm
arm
80mhz-support
a-channels <a-channel>
air-time-fairness-mode {<default-access>| <fair-access>| <preferred-access>}
band-steering-mode {balance-bands|prefer-5ghz| force-5ghz| disable}
client-aware
client-match [calc-interval <seconds>| calc-threshold <threshold> | debug <level>| holdtime
<number> | max-adoption <count>| max-request <count> |nb-matching <percentage> | slb-mode
<mode>
g-channels
max-tx-power
min-tx-power
scanning
wide-bands {<none>| <all>| <2.4>| <5>}
no…
Description
This command assigns an Adaptive Radio Management (ARM) profile for a W-IAP and configures ARM features
such as band steering, spectrum load balancing, airtime fairness mode, and access control features.
Syntax
Command/Parameter
Description
Range
Default
80mhz-support
Enables the use of 80 MHz channels on
APs with 5GHz radios, which support a very
high throughput.
NOTE: Only the APs that support 802.11ac
can be configured with 80 MHz channels.
—
—
a-channels <a-channel>
Configures 5 GHz channels.
—
—
air-time-fairness-mode
Allows equal access to all clients on the
wireless medium, regardless of client type,
capability, or operating system and
prevents the clients from monopolizing
resources. You can configure any of the
following modes:
defaultaccess,fairaccess,
preferredaccess
defaultaccess
balancebands,
prefer5ghz, force5ghz,
balancebands
{<default-access>| <fairaccess>| <preferred-access>}
l
l
l
band-steering-mode
{<balance-bands>|<prefer5ghz>|<force-5ghz>|
<disable>}
32 | arm
default-access — To provide access
based on client requests. When this
mode is configured, the per user and
per SSID bandwidth limits are not
enforced.
fair-access — To allocate Airtime evenly
across all the clients.
preferred-access — To set a preference
where 11n clients are assigned more
airtime than 11a/11g. The 11a/11g
clients get more airtime than 11b. The
ratio is 16:4:1.
Assigns the dual-band capable clients to
the 5 GHz band on dual-band. It reduces
co-channel interference and increases
available bandwidth for dual-band clients,
because there are more channels on the 5
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command/Parameter
Description
Range
GHz band than on the 2.4 GHz band. You
can configure any of the following bandsteering modes:
disable
l
l
l
l
Default
prefer-5ghz — To allow the W-IAP to
steer the client to 5 GHz band (if the
client is 5 GHz capable). However, the
W-IAP allows the client connection on
the 2.4 GHz band if the client
persistently attempts for 2.4 GHz
association.
force-5ghz — To enforce 5 GHz band
steering mode on the W-IAPs, so that
the 5 GHz capable clients are allowed to
use only the 5GHz channels.
balance-bands — To allow the W-IAPs to
balance the clients across the two 2.4
GHz and 5 GHz radio and to utilize the
available bandwidth.
disable — To allow the clients to select
the bands.
client-aware
Enables the client aware feature. When
enabled, the W-IAP will not change
channels for the Access Points when clients
are active, except for high priority events
such as radar or excessive noise. The client
aware feature must be enabled in most
deployments for a stable WLAN.
client-match
Enables enable the client match feature on
APs. When the client match feature is
enabled on a W-IAP, the W-IAP measures
the RF health of its associated clients. If
spectrum load balancing is triggered and a
client's Received Signal Strength Indication
(RSSI) is or less than 20 dB , clients are
moved from one AP to another for better
performance and client experience. In the
current release, the client match feature is
supported only within a W-IAP cluster.
—
Enabled
calc-interval<seconds>
Configures an interval at which client match
is calculated.
10-600
30
seconds
calc-threshold <threshold>
Configures a threshold that takes
acceptance client count difference among
all the channels of Client match into
account. When the client load on an AP
reaches or exceeds the threshold in
comparison, client match is enabled on that
AP.
1-255
2
debug <level>
Displays information required for
debugging client match issues.
0-4
0
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
0—none, 1—
arm | 33
Command/Parameter
Description
Range
Default
error, 2—
information,
3—debug,
4—dump
holdtime <number>
Configures a hold time for client match.
1—1800
900
max-adoption <count>
Configure a maximum number for adopting
clients.
0-100
5
max-request <count>
Configures the maximum number of
requests for client match.
0-100
5
nb-matching <percentage>
Configures a percentage value to be
considered in the same virtual RF
neighborhood of Client match.
20-100%
75%
slb-mode <mode>
Configures a balancing strategy for client
match.
1—3
1
1—Channelbased
2—Radiobased
3—Channel
and Radio
based
g-channels <g-channel>
Configures 2.4 GHz channels.
—
—
min-tx-power <power>
Sets the minimum transmission power. This
indicates the minimum Effective Isotropic
Radiated Power (EIRP). If the minimum
transmission EIRP setting configured on an
AP is not supported by the AP model, this
value is reduced to the highest supported
power setting.
0-127 dBm
18
max-tx-power <power>
Sets the highest transmit power levels for
the AP. If the maximum transmission EIRP
configured on an AP is not supported by the
AP model, the value is reduced to the
highest supported power setting.
0-127 dBm
127
NOTE: Higher power level settings may be
constrained by local regulatory
requirements and AP capabilities.
34 | arm
scanning
Allows the W-IAPs to scan other channels
for RF Management and Wireless Intrusion
Protection System enforcement.
—
Disabled
wide-bands {<none>| <all>|
<2.4>| <5>}
Allows administrators to configure 40 MHz.
channels in the 2.4 GHz and 5.0 GHz
bands. 40 MHz channels are two 20 MHz
adjacent channels that are bonded
together. The 40 MHz channels double the
none, all,
2.4, and 5
5
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command/Parameter
Description
Range
Default
—
—
frequency bandwidth available for data
transmission. For high performance, enter
5GHz. If the AP density is low, enter
2.4GHz.
Removes the current value for that
parameter and return it to its default setting
no…
Usage Guidelines
Use this command to configure ARM features on a W-IAP. ARM ensures low-latency roaming, consistently high
performance, and maximum client compatibility in a multi-channel environment. By ensuring the fair distribution of
available Wi-Fi bandwidth to mobile devices, ARM ensures that data, voice, and video applications have sufficient
network resources at all times. ARM allows mixed 802.11ac, a, b, g, and n client types to inter-operate at the highest
performance levels.
Example
The following example configures an ARM profile:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# arm
AP)(ARM)# 80mhz-support
AP)(ARM)# a-channels 44
AP)(ARM)# min-tx-power 18
AP)(ARM)# max-tx-power 127
AP)(ARM)# band-steering-mode prefer-5ghz
AP)(ARM)# air-time-fairness-mode fair-access
AP)(ARM)# scanning
AP)(ARM)# client-aware
AP)(ARM)# client-match
AP)(ARM)# wide-bands 5
AP)(ARM)# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.1-4.0
This command is modified.
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration and ARM configuration sub-mode.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
arm | 35
attack
attack
drop-bad-arp-enable
fix-dhcp-enable
no…
poison-check-enable
Description
This command enables firewall settings to protect the network against wired attacks, such as ARP attacks or
malformed DHCP packets, and notify the administrator when these attacks are detected.
Syntax
Command/Parameter
Description
drop-bad-arp-enable
Enables the W-IAP to block the bad ARP request.
fix-dhcp-enable
Enables the W-IAP to fix the malformed DHCP packets.
poison-check-enable
Enables the W-IAP to trigger an alert notifying the user about the
ARP poisoning that may have been caused by the rogue APs.
no…
Removes the specified configuration parameter.
Usage Guidelines
Use this command to block ARP attacks and to fix malformed DHCP packets.
Example
The following example configures firewall settings to protect the network from Wired attacks:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# attack
AP)(ATTACK)# drop-bad-arp-enable
AP)(ATTACK)# fix-dhcp-enable
AP)(ATTACK)# poison-check-enable
AP)(ATTACK)# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
36 | attack
W-IAP Platform
Command Mode
All platforms
Configuration and Attack configuration sub-mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
auth-failure-blacklist-time
auth-failure-blacklist-time <seconds>
Description
This command allows the W-IAPs to dynamically blacklist the clients when they exceed the authentication failure
threshold.
Syntax
Parameter
Description
Default
auth-failure-blacklisttime <seconds>
Configures the duration in seconds for which the clients
that exceed the maximum authentication failure
threshold are blacklisted.
3600
Usage Guidelines
Use this command to dynamically blacklist the clients that exceed the authentication failure threshold configured for
a network profile.
Example
The following example blacklists the clients dynamically:
(Instant AP)(config)# auth-failure-blacklist-time 60
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
auth-failure-blacklist-time | 37
auth-survivability cache-time-out
auth-survivability cache-time-out <time-out>
Description
This command configures an interval after which the authenticated credentials of the clients stored in the cache
expire. When the cache expires, the clients are required to authenticate again.
Syntax
Parameter
Description
Range
Default
auth-survivability
cache-time-out
Indicates the duration after which the
authenticated credentials in the cache expire.
1-99 hours
24 hours
Usage Guidelines
Use this command when the authentication survivability is enabled on a network profile, to set a duration after which
the authentication credentials stored in the cache expires. To enable the authentication survivability feature, use the
auth-survivability in WLAN SSID profile sub-mode.
Example
(Instant AP) (config)# auth-survivability cache-time-out 60
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
38 | auth-survivability cache-time-out
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
blacklist-client
blacklist-client <MAC-address>
no…
Description
This command allows you to manually blacklist the clients by using MAC addresses of the clients.
Syntax
Parameter
Description
blacklist-client <MAC-address>
Adds the MAC address of the client to the blacklist.
no…
Removes the specified configuration parameter.
Usage Guidelines
Use this command to blacklist the MAC addresses of clients.
Example
The following command blacklists a W-IAP client:
(Instant AP)(config)# blacklist-client 01:23:45:67:89:AB
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
blacklist-client | 39
blacklist-time
blacklist-time <seconds>
Description
This command sets the duration in seconds for which the clients can be blacklisted due to an ACL rule trigger.
Syntax
Parameter
Description
Default
blacklist-time <seconds>
Sets the duration in seconds for blacklisting clients due
to an ACL rule trigger.
3600
Usage Guidelines
Use this command to configure the duration in seconds for which the clients can be blacklisted when the blacklisting
rule is triggered.
Examples
The following command configures the duration for blacklisting clients:
(Instant AP) (config) # blacklist-time 30
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
40 | blacklist-time
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
calea
calea
encapsulation-type <gre>
ip <IP-address>
ip mtu <size>
gre-type <type>
no...
Description
This command creates a Communications Assistance for Law Enforcement Act (CALEA) profile to enable W-IAPs
for Lawful Intercept (LI) compliance and CALEA integration.
Syntax
Command/Parameter
Description
Range
Default
calea
Enables calea configuration sub-mode for
CALEA profile configuration.
—
—
encapsulation-type
<gre>
Specifies the encapsulation type for Generic
Routing Encapsulation (GRE) packets.
GRE
GRE
ip <IP-address>
Configures the IP address of the CALEA
server on a W-IAP.
—
—
ip mtu <size>
Configures the Maximum Transmission Unit
size to use.
68—1500
1500
gre-type
Specifies GRE type.
—
25944
no…
Removes the configuration
—
—
Usage Guidelines
Use this command to configure a W-IAP to support Lawful Intercept (LI). LI allows the Law Enforcement Agencies
(LEA) to conduct an authorized electronic surveillance. Depending on the country of operation, the service providers
(SPs) are required to support LI in their respective networks.
In the United States, SPs are required to ensure LI compliance based on CALEA specifications. LI compliance in the
United States is specified by the CALEA.
For more information on configuring W-IAPs for CALEA integration, see Dell Networking W-Series Instant User
Guide.
Example
The following example configures a CALEA profile:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# calea
AP)(calea)# ip 192.0.8.29
AP)(calea)# ip mtu 1500
AP)(calea)# encapsulation-type gre
AP)(calea)# gre-type 25944
AP)(calea)# end
AP)# commit apply
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
calea | 41
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.4
This command is introduced.
Command Information
42 | calea
W-IAP Platform
Command Mode
All platforms
Configuration mode and access rule configuration sub-mode.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
cellular-uplink-profile
cellular-uplink-profile <profile>
4g-usb-type <4G-usb-type>
modem-isp <modem_isp>
modem-country <modem-country>
usb-auth-type <usb_authentication_type>
usb-dev <usb-dev>
usb-dial <usb-dial>
usb-init <usb-init>
usb-modeswitch <usb-modeswitch>
usb-passwd <usb-passwd>
usb-tty <usb-tty>
usb-type <usb-type>
usb-user <usb-user>
modem-isp <modem_isp>
modem-country <modem-country>
no…
Description
This command provisions the cellular (3G/4G) uplink profiles on a W-IAP.
Syntax
Parameter
Description
cellular-uplink-profile
<profile>
Configures a 3G or 4G cellular
profile for a W-IAP.
4g-usb-type <4G-usb-type>
Configures the driver type for
the 4G modem.
ether-lte,
pantech-lte,
none
—
modem-isp <modem_isp>
Specifies the name of the ISP
to connect.
—
—
modem-country <modem-country>
Specifies the country for the
deployment.
—
—
usb-auth-type <usb_
authentication_type>
Specifies the authentication
type for USB.
PAP, CHAP
PAP
usb-dev <usb-dev>
Specifies the device ID of the
USB modem.
—
—
usb-dial <usb-dial>
Specifies the parameter to dial
the cell tower.
—
—
usb-init <usb-init>
Specifies the parameter name
to initialize the modem.
—
—
usb-passwd <usb-passwd>
Specifies the password for the
account associated with the
subscriber of the selected ISP.
—
—
usb-modeswitch <usbmodeswitch>
Specifies the parameter used
to switch modem from storage
mode to modem mode.
—
—
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Range
—
Default
—
cellular-uplink-profile | 43
Parameter
Description
Range
Default
usb-type <usb-type>
Configures the driver type for
the 3G modem.
acm,
airprime, hso,
option,
pantech-3g,
sierra-evdo,
sierragsm,none
—
usb-tty <usb-tty>
Specifies the modem tty port.
—
—
usb-user <usb-user>
Specifies the username of
subscriber of the selected ISP.
—
—
no…
Removes the specified
configuration parameter.
—
—
Usage Guidelines
Use this command to configure a cellular uplink profile on a W-IAP and modem parameters 3G /4G uplink
provisioning. Instant supports the use of 3G/4G USB modems to provide Internet backhaul to an Instant network.
The 3G/4G USB modems can be used to extend client connectivity to places where an Ethernet uplink cannot be
configured. This enables the W-IAPs to automatically choose the available network in a specific region.
The 3G and 4G LTE USB modems can be provisioned on W-IAP3WN/3WNP and W-IAP155/155P.
Types of Modems
The following 3G modems are supported:
l
USBConnect 881 (Sierra 881U)
l
Quicksilver (Globetrotter ICON 322)
l
UM100C (UTstarcom)
l
Icon 452
l
Aircard 250U (Sierra)
l
USB 598 (Sierra)
l
U300 (Franklin wireless)
l
U301 (Franklin wireless)
l
USB U760 for Virgin (Novatel)
l
USB U720 (Novatel/Qualcomm)
l
UM175 (Pantech)
l
UM150 (Pantech)
l
UMW190(Pantech)
l
SXC-1080 (Qualcomm)
l
Globetrotter ICON 225
l
UMG181
l
NTT DoCoMo L-05A (LG FOMA L05A)
l
NTT DoCoMo L-02A
44 | cellular-uplink-profile
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
l
ZTE WCDMA Technologies MSM (MF668?)
l
Fivespot (ZTE)
l
c-motech CNU-600
l
ZTE AC2736
l
SEC-8089 (EpiValley)
l
Nokia CS-10
l
NTT DoCoMo L-08C (LG)
l
NTT DoCoMo L-02C (LG)
l
Novatel MC545
l
Huawei E220 for Movistar in Spain
l
Huawei E180 for Movistar in Spain
l
ZTE-MF820
l
Huawei E173s-1
l
Sierra 320
l
Longcheer WM72
l
U600 (3G mode)
l
Sierra USB-306 (HK CLS/1010 (HK))
l
Sierra 306/308 (Telstra (Aus))
l
Sierra 503 PCIe (Telstra (Aus))
l
Sierra 312 (Telstra (Aus))
l
Aircard USB 308 (AT&T's Shockwave)
l
Compass 597(Sierra) (Sprint)
l
U597 (Sierra) (Verizon)
l
Tstick C597(Sierra) (Telecom(NZ))
l
Ovation U727 (Novatel) (Sprint)
l
USB U727 (Novatel) (Verizon)
l
USB U760 (Novatel) (Sprint)
l
USB U760 (Novatel) (Verizon)
l
Novatel MiFi 2200 (Verizon Mifi 2200)
l
Huawei E272, E170, E220 (ATT)
l
Huawei E169, E180,E220,E272 (Vodafone/SmarTone (HK))
l
Huawei E160 (O2(UK))
l
Huawei E160 (SFR (France))
l
Huawei E220 (NZ and JP)
l
Huawei E176G (Telstra (Aus))
l
Huawei E1553, E176 (3/HUTCH (Aus))
l
Huawei K4505 (Vodafone/SmarTone (HK))
l
Huawei K4505 (Vodafone (UK))
l
ZTE MF656 (Netcom (norway))
l
ZTE MF636 (HK CSL/1010)
l
ZTE MF633/MF636 (Telstra (Aus))
l
ZTE MF637 (Orange in Israel)
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
cellular-uplink-profile | 45
l
Huawei E180, E1692,E1762 (Optus (Aus))
l
Huawei E1731 (Airtel-3G (India))
l
Huawei E3765 (Vodafone (Aus))
l
Huawei E3765 (T-Mobile (Germany)
l
Huawei E1552 (SingTel)
l
Huawei E1750 (T-Mobile (Germany))
l
UGM 1831 (TMobile)
l
Huawei D33HW (EMOBILE(Japan))
l
Huawei GD01 (EMOBILE(Japan))
l
Huawei EC150 (Reliance NetConnect+ (India))
l
KDDI DATA07(Huawei) (KDDI (Japan))
l
Huawei E353 (China Unicom)
l
Huawei EC167 (China Telecom)
l
Huawei E367 (Vodafone (UK))
l
Huawei E352s-5 (T-Mobile (Germany))
l
Huawei K4505 (Vodafone/SmarTone (HK))
l
Huawei K4505 (Vodafone (UK))
l
ZTE MF656 (Netcom (norway))
l
ZTE MF636 (HK CSL/1010)
l
ZTE MF633/MF636 (Telstra (Aus))
l
ZTE MF637 (Orange in Israel)
l
Huawei E180, E1692,E1762 (Optus (Aus))
l
Huawei E1731 (Airtel-3G (India))
l
Huawei E3765 (Vodafone (Aus))
l
Huawei E3765 (T-Mobile (Germany)
l
Huawei E1552 (SingTel)
l
Huawei E1750 (T-Mobile (Germany))
l
UGM 1831 (TMobile)
l
Huawei D33HW (EMOBILE(Japan))
l
Huawei GD01 (EMOBILE(Japan))
l
Huawei EC150 (Reliance NetConnect+ (India))
l
KDDI DATA07(Huawei) (KDDI (Japan))
l
Huawei E353 (China Unicom)
l
Huawei EC167 (China Telecom)
l
Huawei E367 (Vodafone (UK))
l
Huawei E352s-5 (T-Mobile (Germany))
l
Huawei D41HW
l
ZTE AC2726
The following table lists the supported 4G modems.
l
Netgear U340
l
Netgear Aircard 341u
l
Fraklin Wireless u770
46 | cellular-uplink-profile
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
l
Huawei 3276s-150
l
MC551L
l
Pantech UML295
l
Pantech UML290
When UML290 runs in auto detect mode, the modem can switch from 4G network to 3G network or vice-versa
based on the signal strength. To configure the UML290 for the 3G network only, manually set the USB type to
pantech-3g. To configure the UML290 for the 4G network only, manually set the 4G USB type to pantech-lte.
Example
The following example configures a cellular uplink profile:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config) # cellular-uplink-profile
AP)(cellular-uplink-profile)# 4g-usb-type pantech-lte
AP)(cellular-uplink-profile)# modem-country India
AP)(cellular-uplink-profile)# modem-isp example
AP)(cellular-uplink-profile)# usb-auth-type PAP
AP)(cellular-uplink-profile)# usb-user user1
AP)(cellular-uplink-profile)# usb-passwd user123
AP)(cellular-uplink-profile)# modem-country India
AP)(cellular-uplink-profile)# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and cellular uplink profile configuration submode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
cellular-uplink-profile | 47
clear
clear
ap <ip-address>
arp <ip-address>
client <mac>
datapath {session-all| statistics}
Description
This command clears various user-configured values from the running configuration on a W-IAP.
Syntax
Parameter
Description
ap <ip-address>
Clears all W-IAP related information.
arp <ip-address>
Clears all ARP table information for a W-IAP.
client <mac>
Clears all information pertaining to a W-IAP client.
datapath {sessionall| statistics}
Clears all configuration information and statistics for datapath modules and user
sessions.
Usage Guidelines
Use the clear command to clear the current information stored in the running configuration of a W-IAP.
Example
The following command clears all information related to a W-IAP:
(Instant AP)# clear ap 192.0.2.3
Command History
Version
Description
Dell Networking WSeries Instant
6.2.1.0-3.3
This command is introduced.
Command Information
48 | clear
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
clear airgroup state statistics
clear airgroup state statistics
Description
This command removes the AirGroup statistics.
Usage Guidelines
Use this command to remove AirGroup details from the W-IAP database.
Example
The following command clears AirGroup statistics:
(Instant AP)(config)# clear airgroup state statistics
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
clear airgroup state statistics | 49
clear-cert
clear-cert {ca| server}
Description
This command clears client and server certificates from the W-IAP database.
Syntax
Parameter
Description
ca
Clears all certificates uploaded for the client system.
server
Clears all Server certificates.
Usage Guidelines
Use this command to clear the certificates from the W-IAP database.
Example
The following command shows an example for clearing server certificates:
(Instant AP)# clear-cert server
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
50 | clear-cert
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
clock set
clock set <year> <month> <day> <time>
Description
This command sets the date and time on the W-IAP system clock.
Syntax
Parameter
Description
Range
<year>
Sets the year. Requires all 4 digits.
Numeric
<month>
Sets the month.
1-12
<day>
Sets the day.
1-31
<time>
Sets the time. Specify hours, minutes, and
seconds separated by spaces.
Numeric
Usage Guidelines
You can configure the year, month, day, and time. Specify the time using a 24-hour clock with hours, minutes and
seconds separated by spaces.
Example
The following example sets the clock to 21 May 2013, 1:03:52 AM:
(Instant AP)# clock set 2013 5 21 1 3 52
Command History
Version
Description
Dell Networking WSeries Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
clock set | 51
clock summer-time
clock summer-time <timezone> recurring <start-week> <start-day> <start-month> <start-hour>
<eweek> <eday> <emonth> <ehour>
no…
Description
This command configures daylight saving for the time zones that support daylight saving time.
Syntax
Parameter
Description
Range
clock summer-time
<timezone>
Configures Daylight Saving time.
Timezones
that support
daylight
saving
configuration
recurring
Indicates the recurrences.
—
<start-week>
Indicates the week from which the daylight saving configuration is
effective.
—
<start-day>
Indicates the day from which the daylight saving configuration
applies.
—
<start-month>
Indicates the month from which the daylight saving configuration
applies.
—
<start-hour>
Indicates the hour from which the daylight saving configuration
applies.
1-24
<eweek>
Indicates the week in which the daylight saving configuration ends.
—
<eday>
Indicates the day on which daylight saving configuration ends.
—
<emonth>
Indicates the month in which daylight saving configuration ends.
—
<ehour>
Indicates the hour at which daylight saving configuration ends.
1-24
no…
Removes the configuration
—
Usage Guidelines
Use this command to configure daylight saving for the timezones that support daylight saving. When enabled, the
daylight saving time ensures that the W-IAPs reflect the seasonal time changes in the region they serve.
Example
The following example configures daylight saving for a timezone:
(Instant AP)(config)# clock summer-time PST recurring 7 10 March 9PM 38 10 October 9PM
(Instant AP)(config)# end
(Instant AP)# commit apply
52 | clock summer-time
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
clock summer-time | 53
clock timezone
clock timezone <name> <hour-offset> <minute-offset>
no…
Description
This command sets the timezone on a W-IAP.
Syntax
Parameter
Description
Range
clock timezone
<name>
Configures the required timezone.
All supported
timezones
<hour-offset>
Specifies the hours offset from the Universal Time Clock
(UTC).
—
<minute-offset>
Specifies the hours offset from the Universal Time Clock
(UTC).
—
no…
Removes the timezone configuration.
—
Usage Guidelines
Use this command to set the timezone on a W-IAP.
Example
The following example configures the PST timezone:
(Instant AP) (config)# clock timezone PST -8 0
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
54 | clock timezone
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
commit
commit {apply [no-save]| revert}
Description
This command allows you to commit configuration changes performed during a user session. You can also revert the
changes that are already committed.
Syntax
Parameter
Description
apply
Applies and saves the W-IAP configuration changes.
no-save
Applies the configuration changes to the cluster, but does not save the
configuration. To save the configuration, run the write memory or commit apply
command.
revert
Reverts the changes committed to the current configuration of a W-IAP.
Usage Guidelines
Each command processed by the Virtual Controller is applied on all the slave W-IAPs in a cluster. The changes
configured in a CLI session are saved in the CLI context. The CLI does not support the configuration data exceeding
the 4K buffer size in a CLI session: therefore, Dell recommends that you configure fewer changes at a time and
apply the changes at regular intervals.
To apply and save the configuration changes, use the commit apply command. To apply the configuration changes
without saving the configuration, use the commit apply no-save command.
Example
The following command allows you to commit the configuration changes:
(Instant AP) # commit apply
The following command reverts the already committed changes.
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.14.0
This command is modified.
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
commit | 55
configure terminal
configure terminal
Description
This command allows you to enter configuration commands.
Syntax
No parameters.
Usage Guidelines
Upon entering this command, the enable mode prompt changes to:
(Instant AP)(config)#
To return to EXEC mode, enter Ctrl-Z, end or exit.
Example
The following command allows you to enter configuration commands:
(Instant AP) # configure terminal
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode.
56 | configure terminal
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
console
console
enable
disable
Description
This command enables console access to a W-IAP through the serial port.
Syntax
Command/Parameter
Description
console
Allows you to enter the console configuration mode.
enable
Enables console access to the W-IAP.
disable
Disables console access to the W-IAP.
Usage Guidelines
Use this command to enable or disable access to the W-IAP console and thus allow users to configure W-IAP
settings or debug system errors. By default, the console access to the W-IAP is enabled.
Example
The following example disables console access to the W-IAP:
(Instant
(Instant
(Instant
(Instant
AP)(config)# console
AP)(console)# disable
AP)(console)# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.4.0.24.1
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Console configuration sub mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
console | 57
content-filtering
content-filtering
no…
Description
This command enables content filtering feature. When content filtering is enabled on an SSID, all DNS requests to
non-corporate domains on this wireless network are sent to OpenDNS.
Syntax
Command/Parameter
Description
content-filtering
Enables content filtering.
no
Removes the configuration.
Usage Guidelines
Use this command to enable content filter. With content filter feature enabled, you can:
l
Prevent known malware hosts from accessing your wireless network.
l
Improve employee productivity by limiting access to certain websites.
l
Reduce bandwidth consumption significantly.
You can enable content filtering on an SSID. When enabled, all DNS requests to non-corporate domains on this
SSID are sent to the open DNS server.
Example
The following example enables content filtering:
(Instant AP)# content-filtering
(Instant AP)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
58 | content-filtering
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
convert-aos-ap
convert-aos-ap <mode> <controller-IP>
Description
This command allows you to provision a W-IAP as a Campus AP or Remote AP in a controller-based network, or as
a standalone AP.
Syntax
Parameter
Description
Range
<mode>
Provisions the W-IAP as remote AP or campus AP in a
controller-based network.
W-IAP, CAP.
<controller-IP>
Allows you to specify the IP address of the controller to which
the Remote AP or Campus AP will be connected.
—
Usage Guidelines
Before converting a W-IAP, ensure that both the W-IAP and controller are configured to operate in the same
regulatory domain. A W-IAP can be converted to a Campus AP and Remote AP only if the controller is running
ArubaOS 6.1.4 or later.
Example
The following command allows you to convert a W-IAP to a remote AP:
(Instant AP)# convert-aos-ap W-IAP 192.0.2.5
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
convert-aos-ap | 59
copy
copy {config tftp <ip-address> <filename>|core-file tftp <ip-address>| flash tftp <ip-address>
<filename>| tftp <ip-address> <filename> {cpserver cert <password> format {p12|pem} | portal
logo | system {1xca [format {der|pem}]|1xcert <passsword>[format {p12|pem}]|config|flash}}
Description
This command copies files to and from the W-IAP.
Syntax
Parameter
Description
config
Copies a configuration file to the TFTP server.
core-file
Copies a core file to the TFTP server.
flash
Copies a file from flash to the TFTP server or to flash from a TFTP server.
tftp
Copies files and certificates to the W-IAP database from a TFTP server.
<ip-address>
Copies files to the specified TFTP server IP address.
<file-name>
Indicates the name of the file to be copied.
cpserver
Copies internal captive portal server certificate.
cert <password>
portal
Copies customized logo for the internal captive portal server.
logo
system
Copies the file to the system partition.
1xca
Copies the CA certificate used for 802.1X authentication from the TFTP server.
der
Indicates the system partition file extensions.
pem
1xcert
Copies the server certificate used for 802.1X authentication from the TFTP
server.
<passsword>
Indicates the password for certificate authentication.
p12
Indicates the certificate file extensions.
pem
Usage Guidelines
Use this command to save backup copies of the configuration file to a TFTP server, or to load a certificate file and
customized logo from a TFTP server to the W-IAP database.
Example
The following example copies a configuration file to the TFTP server:
(Instant AP)# copy config tftp 10.0.0.1 filename.cfg
60 | copy
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command History
Version
Description
Dell Networking W-Series Instant
6.3.1.1-4.0
This command was modified.
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
copy | 61
deny-inter-user-bridging
deny-inter-user-bridging
no…
Description
This command disables bridging traffic between two clients of a W-IAP on the same VLAN. Bridging traffic between
the clients will be sent to the upstream device to make the forwarding decision.
Syntax
Parameter
Description
deny-inter-user-bridging
Prevents the inter-user bridging.
no…
Removes the configuration.
Usage Guidelines
Use this command if you have security and traffic management policies defined for upstream devices.
Example
The following command disables inter-user bridging:
(Instant AP)(config)# deny-inter-user-bridging
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
62 | deny-inter-user-bridging
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
deny-local-routing
deny-local-routing
no…
Description
This command disables routing traffic between two clients of a W-IAP on different VLANs. Routing traffic between
the clients will be sent to the upstream device to make the forwarding decision.
Syntax
Parameter
Description
deny-local-routing
Disables local routing of traffic.
no…
Removes the configuration.
Usage Guidelines
Use this command to prevent the local routing of traffic if you have security and traffic management policies defined
for upstream devices.
Example
The following command disables local routing:
(Instant AP)(config)# deny-local-routing
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
deny-local-routing | 63
device-id
device-id <device>
Description
This command assigns an ID for the AP device.
Syntax
Parameter
Description
device-id <device>
Configures an ID for the W-IAP device.
Usage Guidelines
Use this command to configure a device identification.
Example
The following example configures a device ID:
(Instant AP)(config)# device-ID Device1
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
64 | device-id
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
disable-prov-ssid
disable-prov-ssid
no…
Description
This command disables the default provisioning SSID enabled in the W-IAP factory default settings.
Usage Guidelines
The default provisioning SSID is used during the initial configuration of the W-IAP if the automatic provisioning of the
W-IAP fails and if W-AirWave is not reachable.
Example
The following example disables the default provisioning SSID:
(Instant AP)# disable-prov-ssid
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
disable-prov-ssid | 65
disconnect-user
disconnect-user {<addr>|all|mac <mac>| network <name>}
Description
This command disconnects the clients from a W-IAP.
Syntax
Parameter
Description
<addr>
Allows you to disconnect a client by specifying the IP address of the client.
all
Disconnects all users associated with a W-IAP.
mac <mac>
Allows you to disconnect a client by specifying the MAC address of the client.
network <name>
Allows you to disconnect the clients connected to a specific network.
Example
The following example disconnects all clients associated with a W-IAP:
(Instant AP)# disconnect-user
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
66 | disconnect-user
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
download-cert
download-cert {ca|cp|server} <URL>
Description
This command allows you to download the client, authentication server, and captive portal server certificates from
an FTP or TFTP server, or by using an HTTP URL.
Syntax
Parameter
Description
ca
Downloads client certificates.
cp
Downloads captive portal server certificates.
server
Downloads Server certificates.
<url>
Allows you to specify the FTP, TFTP, or HTTP URL.
Usage Guidelines
Use this command to download certificates.
Example
The following command shows an example for downloading CA client certificates:
(Instant AP)# download-cert ca ftp://192.0.2.7
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.1-4.0
This command is modified.
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
download-cert | 67
dpi
dpi
no…
Description
This command enables visualization of traffic from wired and wireless clients associated with a W-IAP.
Syntax
Parameter
Description
dpi
Enables AppRF visualization.
no…
Removes the configuration.
Usage Guidelines
Use this command to enable AppRF visibility for wired and wireless clients associated with a W-IAP. AppRF
supports an application and web-filtering service that allows creating firewall policies based on types of application.
AppRF includes the following capabilities:
l
Access control, QoS, and bandwidth contract rules based on application and application categories.
l
Content filters based on web categories and reputation scores (security ratings).
For more information access rule configuration and web-filtering options, see Dell Networking W-Series Instant
6.4.0.2-4.1 User Guide and the wlan access-rule command page.
The application and application category based access rule configuration and visualization are not supported on WIAP104/105, W-IAP134/135, and W-IAP3WN/3WNP platforms. Only the web category charts are displayed for
these W-IAP models.
Example
The following command configures DPI support:
(Instant AP)(config)# dpi
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.4.0.24.1
This command is introduced.
Command Information
68 | dpi
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
dynamic-cpu-mgmt
dynamic-cpu-mgmt {auto| disable| enable}
Description
This command enables or disables the dynamic CPU management feature, to manage resources across different
functions performed by a W-IAP.
Syntax
Parameter
Description
auto
Configures the W-IAP to automatically enable or disable CPU management feature
during run-time. When configured, the W-IAP determines the need for enabling or
disabling CPU management, based on the real-time load calculations taking into
account all different functions that the CPU needs to perform.
The auto option is the default and recommended setting.
disable
Disables CPU management on all APs, typically for small networks. This setting
protects the user experience.
enable
Enables the CPU management feature. When configured, the client and network
management functions are protected. This setting helps in large networks with a
high client density.
Usage Guidelines
Use this command to enable or disable resource management across different functions performed by a W-IAP.
Example
The following example enables the automatic enabling or disabling of CPU management:
(Instant AP)(config)# dynamic-cpu-mgmt auto
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.4.0.0
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
dynamic-cpu-mgmt | 69
dynamic-radius-proxy
dynamic-radius-proxy
no…
Description
This command enables the use of IP Address of the Virtual Controller for communication with external RADIUS
servers.
Syntax
Command/Parameter
Description
dynamic-radius-proxy
Enables dynamic RADIUS proxy feature to allow the Virtual
Controller network to use the IP address of the Virtual Controller
when communicating with the external RADIUS servers.
no…
Removes the configuration.
Usage Guidelines
Ensure that you set the Virtual Controller IP address as a NAS client in the RADIUS server when Dynamic RADIUS
proxy is enabled.
Example
The following example enables the dynamic RADIUS proxy feature:
(Instant AP)(config)# dynamic-radius-proxy
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
70 | dynamic-radius-proxy
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
enet-vlan
enet-vlan <vlan-ID>
no…
Description
This command configures a VLAN for Ethernet connections.
Syntax
Parameter
Description
Range
enet-vlan <vlan-ID>
Configures VLAN for Ethernet ports and wired profiles
0–4093
no…
Removes the configuration
—
Usage Guidelines
Use this command to configure VLAN for the Ethernet connections.
Example
The following example configures VLAN for the Ethernet ports:
(Instant AP)(config)# enet-vlan 200
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
enet-vlan | 71
enet0-bridging
enet0-bridging
Description
This command allows you to use all ports on the APs as downlink ports.
Usage Guidelines
Use this command for W-IAP models that have only one Ethernet port enabled. When Eth0 bridging is configured,
ensure that the uplink for each W-IAP is mesh link, Wi-Fi, or 3G/4G.
Example
The following command enables Eth0 bridging:
(Instant AP)# enet0-bridging
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
72 | enet0-bridging
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
enet0-port-profile
enet0-port-profile <profile>
Description
This command assigns a wired profile to the Ethernet 0 port on a W-IAP.
Syntax
Parameter
Description
enet0-port-profile <profile>
Assigns a wired profile to the Ethernet 0 interface port.
Usage Guidelines
Use this command to assign a wired profile to the Ethernet 0 port to activate the wired profile.
Example
The following command assigns a wired profile to the Ethernet 0 port:
(Instant AP)(config)# enet0-port-profile <name>
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
enet0-port-profile | 73
enet1-port-profile
enet1-port-profile <profile>
Description
This command assigns a wired profile to the Ethernet 1 port on a W-IAP.
Syntax
Parameter
Description
enet1-port-profile <profile>
Assigns a wired profile to the Ethernet 1 interface port.
Usage Guidelines
Use this command to assign a wired profile to the Ethernet 1 port to activate the wired profile.
Example
The following command assigns a wired profile to the Ethernet 1 port:
(Instant AP)(config)# enet1-port-profile <name>
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
74 | enet1-port-profile
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
enet2-port-profile
enet2-port-profile <profile>
Description
This command assigns a wired profile to the Ethernet 2 port on a W-IAP.
Syntax
Parameter
Description
enet2-port-profile <profile>
Assigns a wired profile to the Ethernet 2 interface port.
Usage Guidelines
Use this command to assign a wired profile to the Ethernet 2 port to activate the wired profile.
Example
The following command assigns a wired profile to the Ethernet 2 port:
(Instant AP)(config)# enet2-port-profile <name>
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
enet2-port-profile | 75
enet3-port-profile
enet3-port-profile <profile>
Description
This command assigns a wired profile to the Ethernet 3 port on a W-IAP.
Syntax
Parameter
Description
enet3-port-profile <profile>
Assigns a wired profile to the Ethernet 3 interface port.
Usage Guidelines
Use this command to assign a wired profile to the Ethernet 3 port to activate the wired profile.
Example
The following command assigns a wired profile to the Ethernet 3 port:
(Instant AP)(config)# enet3-port-profile <name>
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
76 | enet3-port-profile
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
enet4-port-profile
enet4-port-profile <profile>
Description
This command assigns a wired profile to the Ethernet 4 port on a W-IAP.
Syntax
Parameter
Description
enet4-port-profile <profile>
Assigns a wired profile to the Ethernet 4 interface port.
Usage Guidelines
Use this command to assign a wired profile to the Ethernet 4 port to activate the wired profile.
Example
The following command assigns a wired profile to the Ethernet 4 port:
(Instant AP)(config)# enet4-port-profile <name>
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
enet4-port-profile | 77
extended-ssid
extended-ssid
no…
Description
This command enables the configuration of additional WLAN SSIDs. Extended SSID is enabled by default in the
factory default settings of Instant APs. Disabling the extended ssid option in the factory default mode will not take
effect.
Syntax
Command/Parameter
Description
extended-ssid
Enables the users to configure additional SSIDs.
no…
Removes the configuration.
Usage Guidelines
Use this command to create additional SSIDs. By default, you can create up to six WLAN SSIDs. With the
Extended SSID option enabled, you can create up to 16 WLANs. The following W-IAPs support 16 WLANs:
l
W-IAP3WNP
l
W-IAP134
l
W-IAP135
The number of SSIDs that become active on each W-IAP depends on the W-IAP platform.
Example
The following example enables the configuration of extended SSIDs:
(Instant AP)(config)# extended-ssid
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
78 | extended-ssid
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
factory-ssid-enable
factory-ssid-enable
Description
This command resets the W-IAP to use the factory configuration.
Syntax
Parameter
Description
factory-ssid-enable
Enables factory SSID configuration.
Usage Guidelines
Use this command to reset a W-IAP to use the factory default SSID.
Example
The following example enables factory default configuration:
(Instant AP)(config)# factory-ssid-enable
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
factory-ssid-enable | 79
firewall-external-enforcement
firewall-external-enforcement pan
disable
enable
ip <address>
port <port>
user <name> <password>
no…
Description
This command configures external firewall details such as Palo Alto Networks (PAN) firewall to enable integration
with the W-IAP.
Syntax
Parameter
Description
Range
Default
firewall-external-enforcement
pan
PAN firewall configuration submode.
—
—
disable
Disables PAN firewall.
—
—
enable
Enables PAN firewall.
—
—
ip <address>
Configures PAN firewall IP
address on the W-IAP
—
—
port <port>
Configures a port for the PAN
firewall
1—65535
443
user <name> <password>
Configures administrator user
credentials of PAN firewall on a
W-IAP.
—
—
no…
Removes the specified
configuration parameter.
—
—
Usage Guidelines
Use this command to enable external firewall integration with W-IAP. In Instant 6.3.1.1-4.0 release, W-IAPs can be
integrated with external firewall such as PAN firewall. The PAN firewall is based on user ID, which provides many
methods for connecting to sources of identity information and associating them with firewall policy rules. The
functionality provided by the PAN firewall based on user ID requires the collection of information from the network.
W-IAP maintains the network (such as mapping IP address) and user information for those clients in the network and
provides the required information for the user ID feature on PAN firewall.
To enable W-IAP integration with PAN firewall, a global profile configured on W-IAP with PAN firewall information
such as IP address, port, user name, password, firewall enabled or disabled status.
Example
The following example configures PAN firewall information on a W-IAP:
(Instant
(Instant
(Instant
(Instant
AP)(config)# firewall-external-enforcement pan
AP)(firewall-external-enforcement pan)# enable
AP)(firewall-external-enforcement pan)# ip 192.0.2.11
AP)(firewall-external-enforcement pan)# port 443
80 | firewall-external-enforcement
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
(Instant AP)(firewall-external-enforcement pan)# user admin1 admin1
(Instant AP)(firewall-external-enforcement pan)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.14.0
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and firewall-external-enforcement sub-mode.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
firewall-external-enforcement | 81
g-channel
g-channel <channel> <tx-power>
Description
This command configures 2.4 GHz radio channels for a specific W-IAP.
Syntax
Parameter
Description
Range
<channel>
Configures the specified 2.4 GHz channel.
The valid channels for a band are
determined by the AP regulatory
domain.
<tx-power>
Configures the specified transmission power values.
0-127 dBm
Usage Guidelines
Use this command to configure radio channels for the 2.4 GHz band for a specific W-IAP.
Example
The following example configures the 2.4 GHz radio channel:
(Instant AP)# g-channel 11 18
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
82 | g-channel
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
g-external-antenna
g-external-antenna <gain>
Description
This command configures external antenna connectors for a W-IAP.
Syntax
Parameter
Description
Range
Default
<gain>
Configures the antenna gain. You can configure gain
value in dBi for the following types of antenna:
Diploe/Omni - 6
—
l
l
l
Dipole/Omni
Panel
Sector
Panel -12
Sector - 12
Usage Guidelines
If your W-IAP has external antenna connectors, you need to configure the transmit power of the system. The
configuration must ensure that the system’s Equivalent Isotropically Radiated Power (EIRP) is in compliance with
the limit specified by the regulatory authority of the country in which the W-IAP is deployed. You can also measure or
calculate additional attenuation between the device and antenna before configuring the antenna gain. To know if your
AP device supports external antenna connectors, see the Install Guide that is shipped along with the AP device.
EIRP and Antenna Gain
The following formula can be used to calculate the EIRP limit related RF power based on selected antennas
(antenna gain) and feeder (Coaxial Cable loss):
EIRP = Tx RF Power (dBm)+GA (dB) - FL (dB)
The following table describes this formula:
Table 9: Formula Variable Definitions
Formula Element
Description
EIRP
Limit specific for each country of deployment
Tx RF Power
RF power measured at RF connector of the unit
GA
Antenna gain
FL
Feeder loss
For information on antenna gain recommended by the manufacturer, see dell.com/support.
Example
The following example configures external antenna connectors for the W-IAP with the 2.4 GHz radio band.
(Instant AP)# g-external-antenna 12
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
g-external-antenna | 83
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode.
84 | g-external-antenna
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
gre per-ap-tunnel
gre per-ap-tunnel
no…
Description
This command configures a generic routing encapsulation (GRE) tunnel from each W-IAP to the VPN/GRE Endpoint
rather than the tunnels created just from the Virtual Controller.
Syntax
Parameter
Description
gre per-ap-tunnel
Creates a GRE tunnel from the W-IAP to the VPN/GRE endpoint.
no…
Removes the configuration.
Usage Guidelines
Use this command to allow the traffic to be sent to the corporate network through a Layer-2 GRE tunnel from the WIAP itself. When a GRE tunnel per W-IAP is created, the traffic need not be forwarded through the Virtual Controller.
Example
The following example creates a GRE tunnel for the W-IAP:
(Instant AP)(config)# gre per-ap-tunnel
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
gre per-ap-tunnel | 85
gre primary
gre primary <name>
no…
Description
This command configures a host for the primary VPN/GRE endpoint.
Syntax
Parameter
Description
gre primary <name>
Specifies the fully qualified domain name (FQDN) of the primary
host.
no…
Removes the configuration.
Usage Guidelines
Use this command to configure the primary VPN/GRE host.
Example
The following example configures a GRE primary host:
(Instant AP)(config)# gre primary <name>
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
86 | gre primary
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
gre type
gre type <type>
Description
This command configures a GRE protocol number as GRE type.
Syntax
Parameter
Description
Range
Default
gre type <type>
Configures the protocol number or IP address for
GRE type
16-bit
protocol
number
0
Usage Guidelines
Use this command to specify GRE type. The 16-bit protocol number uniquely identifies a Layer-2 tunnel. The WIAPs or controllers at both endpoints of the tunnel must be configured with the same protocol number.
Example
The following example configures the GRE type:
(Instant AP)(config)# gre type 0
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
gre type | 87
help
help
Description
This command displays help for the CLI.
Usage Guidelines
This command displays keyboard editing commands that allow you to make corrections or changes to the command
without retyping.
You can also enter the question mark (?) to get various types of command help:
l
When typed at the beginning of a line, the question mark lists all commands available in the current mode.
l
When typed at the end of a command or abbreviation, the question mark lists possible commands that match.
l
When typed in place of a parameter, the question mark lists available options.
Example
The following example shows the output of the help command.
HELP:
Special keys:
BS .... delete previous character
Ctrl-A .... go to beginning of line
Ctrl-E .... go to end of line
Ctrl-F .... go forward one character
Ctrl-B .... go backward one character
Ctrl-D .... delete current character
Ctrl-U, X .. delete to beginning of line
Ctrl-K .... delete to end of line
Ctrl-W .... delete previous word
Ctrl-T .... transpose previous character
Ctrl-P .... go to previous line in history buffer
Ctrl-N .... go to next line in history buffer
Ctrl-Z .... return to root command prompt
Tab .... command-line completion
exit .... go to next lower command prompt
? .... list choices
Help may be requested at any point in a command by entering
a question mark '?'. If nothing matches, the help list will
be empty and you must back up until entering a '?' shows the
available options.
Two styles of help are provided:
1. Full help is available when you are ready to enter a
command argument (e.g. 'show ?') and describes each possible
argument.
2. Partial help is provided when an abbreviated argument is entered
and you want to know what arguments match the input
(e.g. 'show w?'.)
Command History
88 | help
Version
Description
Dell Networking WSeries Instant
6.2.1.0-3.3
This command is introduced.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
help | 89
hostname
hostname <name>
Description
This command changes the hostname of the Virtual Controller.
Syntax
Parameter
Description
<name>
Configures a hostname for the Virtual Controller.
Usage Guidelines
The hostname is used as the default prompt. You can use any alphanumeric character, punctuation, or symbol
characters. When spaces, plus symbols (+), question marks (?), or asterisks (*) are used, enclose the text in quotes.
Example
The following example configures host name for a W-IAP.
(Instant AP)# hostname IAP1
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
90 | hostname
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
hotspot anqp-3gpp-profile
hotspot anqp-3gpp-profile <profile-name>
3gpp-plmn1…3gpp-plmn6 <PLMN-ID>
enable
no…
Description
This command configures a 3rd Generation Partnership Project (3GPP) Cellular Network for hotspots that have
roaming relationships with cellular operators.
Syntax
Parameter
Description
hotspot anqp-3gpp-profile
<profile-name>
Creates a 3GPP profile.
3gpp-plmn1…3gpp-plmn6 <PLMN-ID>
Configures the Public Land Mobile Networks (PLMN) value of the
network. The PLMN value can be specified for first, second, third,
fourth, fifth, and sixth highest priority network.
The PLMN ID consists of a 12-bit Mobile Country Code (MCC) and
the 12-bit Mobile Network Code (MNC).
enable
Activates the configuration profile.
no…
Removes the configuration
Usage Guidelines
Use this command to configure a 3GPP Cellular Network hotspot profile that defines the ANQP information element
(IE) for 3G Cellular Network for hotspots. The IE defined in this profile will be sent in a Generic Advertisement
Service (GAS) query response from a W-IAP in a cellular network hotspot. The 3GPP Mobile Country Code (MCC)
and the 12-bit Mobile Network Code data in the IE can help the client select a 3GPP network when associated with a
hotspot profile and enabled on a WLAN SSID profile.
Example
The following command configures a 3GPP profile:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# hotspot anqp-3gpp-profile cellcorp1
AP)(3gpp "cellcorp1")# 3gpp-plmn1 310026
AP)(3gpp "cellcorp1")# 3gpp_plmn2 208000
AP)(3gpp "cellcorp1")# 3gpp_plmn3 208001
AP)(3gpp "cellcorp1")# enable
AP)(3gpp "cellcorp1")# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
hotspot anqp-3gpp-profile | 91
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and the 3GPP hotspot profile configuration
sub-mode
92 | hotspot anqp-3gpp-profile
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
hotspot anqp-domain-name-profile
hotspot anqp-domain-name-profile <profile-name>
domain-name <domain-name>
enable
no…
Description
This command defines the domain name to be sent in an Access Network Query Protocol (ANQP) information
element in a Generic Advertisement Service (GAS) query response.
Syntax
Parameter
Description
hotspot anqp-domain-name-profile
<profile-name>
Creates a domain profile.
domain-name <domain-name>
Configures a domain name of the hotspot operator.
enable
Enables the configuration profile.
no…
Removes the existing configuration
Usage Guidelines
Use this command to configure a domain name in the ANQP Domain Name profile. If a client uses the Generic
Advertisement Service (GAS) to post an ANQP query to a W-IAP, the W-IAP will return an ANQP Information
Element with the domain name when this profile is associated with a hotspot profile and enabled on a WLAN SSID
profile.
Example
The following command defines a domain name for the ANQP domain name profile:
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# hotspot anqp-domain-name-profile domain1
AP)(domain-name "domain1")# domain-name example.com
AP)(domain-name "domain1")# enable
AP)(domain-name "domain1")# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and the ANQP domain profile configuration
sub-mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
hotspot anqp-domain-name-profile | 93
hotspot anqp-ip-addr-avail-profile
hotspot anqp-ip-addr-avail-profile <profile-name>
enable
ipv4-addr-avail
ipv6-addr-avail
no…
Description
This command defines the available IP address types to be sent in an Access network Query Protocol (ANQP)
information element in a Generic Advertisement Service (GAS) query response.
Syntax
Parameter
Description
hotspot anqp-ip-addr-avail-profile
<profile-name>
Creates an ANQP IP Address availability profile.
enable
Enables the IP address availability profile.
ipv4-addr-avail
Indicates the availability of an IPv4 network.
ipv6-addr-avail
Indicates the availability of an IPv6 network.
no…
Removes the existing configuration.
Usage Guidelines
Use this command to configure the IP Address availability information and IP address types which could be
allocated to the clients after they associate to the hotspot W-IAP.
Example
The following command configures an AP using this profile to advertise a public IPv4 network.
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# hotspot anqp-ip-addr-avail-profile default
AP)(IP-addr-avail "default")# ipv4-addr-avail
AP)(IP-addr-avail "default")# ipv6-addr-avail
AP)(IP-addr-avail "default")# enable
AP)(IP-addr-avail "default")# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and the ANQP IP address availability profile
configuration sub-mode
94 | hotspot anqp-ip-addr-avail-profile
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
hotspot anqp-nai-realm-profile
hotspot anqp-nai-realm-profile <profile-name>
enable
nai-home-realm
nai-realm-auth-id-1 <auth-ID>
nai-realm-auth-id-2 <auth-ID>
nai-realm-auth-value-1 <auth-value>
nai-realm-auth-value-2 <auth-value>
nai-realm-eap-method <eap-method>
nai-realm-encoding <encoding>
nai-realm-name <name>
no…
Description
This command defines a Network Access Identifier (NAI) realm information that can be sent as an Access network
Query Protocol (ANQP) information element in a Generic Advertisement Service (GAS) query response.
Syntax
Parameter
Description
Range
hotspot anqp-nairealm-profile
<profile-name>
Configures a NAI realm hotspot profile.
—
enable
Enables the NAI realm profile.
—
nai-home-realm
Sets the realm in this profile as the NAI Home Realm.
—
nai-realm-auth-id-1
nai-realm-auth-id-2
Configures the NAI realm authentication ID.
Use the nai-realm-auth-id-1 command to send the one of the
following authentication methods for the primary NAI realm ID.
Use the nai-realm-auth-id-2 command to send the one of the
following authentication methods for the secondary NAI realm
ID.
—
<auth-id>
Configures any of the following types of authentication ID:
credential
eap-innerauth
exp-inner-auth
expanded-eap
non-eapinner-auth
reserved
l
l
l
l
l
l
nai-realm-auth-value1
nai-realm-auth-value2
credential— Uses credential authentication.
eap-inner-auth—Uses EAP inner authentication type.
exp-inner-eap— Uses the expanded inner EAP
authentication method.
expanded-eap—Uses the expanded EAP authentication
method.
non-eap-inner-auth—Uses non-EAP inner authentication
type.
reserved—Uses the reserved authentication method.
Configures a value for NAI realm authentication. Use the nairealm-auth-value-1 command to select an authentication
value for the authentication method specified by nai-realmauth-id-1. Use thenai-realm-auth-value-2 command to select
the authentication value for the authentication method
specified bynai-realm-auth-id-2.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
—
hotspot anqp-nai-realm-profile | 95
Parameter
Description
Range
<auth-value>
Configures any of following types of authentication values for
the specified <auth-id>:
sim, usim. nfcsecure, hwtoken,
softoken,
certificate,
unamepassword,
none,
reserved,
vendorspecific
reserved, pap
chap, mschap,
mschapv2,
exp-inner-eap,
expandedeap, reserved
l
For credential <auth-ID>, specify the following values:
l
l
l
l
l
l
l
l
l
l
l
For eap-inner-auth <aut- ID>, specify the following values:
l
l
l
l
l
l
l
l
sim
usim
nfc-secure
hw-token
softoken
certificate
uname-passward
none
reserved
vendor-specific
reserved
pap
chap
mschap
mschapv2
For exp-inner-eap <auth-ID>, specify exp-inner-eap as the
authentication value.
For expanded-eap<auth-ID>, specify expanded-eap as the
authentication value
For non-eap-inner-auth<auth-ID> specify any of the
following values:
l
l
l
l
l
reserved
pap
chap
mschap
mschapv2
nai-realm-eap-method
Configures an EAP method for NAI realm.
<eap-method>
Configures any of the following EAP methods:
l crypto-card— Crypto card authentication
l eap-aka—EAP for UMTS Authentication and Key
Agreement
l eap-sim—EAP for GSM Subscriber Identity Modules
l eap-tls—EAP-Transport Layer Security
l eap-ttls—EAP-Tunneled Transport Layer Security
l generic-token-card—EAP Generic Token Card (EAP-GTC)
l identity— EAP Identity type
l notification—The hotspot realm uses EAP Notification
messages for authentication.
l one-time-password—Authentication with a single-use
password
l peap—Protected Extensible Authentication Protocol
l peapmschapv2— Protected Extensible Authentication
Protocol with Microsoft Challenge Handshake
Authentication Protocol version 2
crypto-card,
eap-aka, eapsim, eap-tls,
eap-ttls,
generic-tokencard, identity
notification,
one-timepassword,
peap,
peapmschapv
2
nai-realm-encoding
<encoding>
Configures a UTF-8 or rfc4282 formatted character string for
NAI realm encoding.
rfc4282,
utf8
96 | hotspot anqp-nai-realm-profile
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Parameter
Description
Range
nai-realm-name
<nai-realm-name>
Configures a name for the NAI realm. The realm name is often
the domain name of the service provider.
—
no…
Removes any existing configuration.
—
Usage Guidelines
Use this command to configure an NAI Realm profile that identifies and describes a NAI realm accessible to the WIAP, and the method used for NAI realm authentication. The settings configured in this profile determine the NAI
realm elements that are included as part of a GAS Response frame.
Example
The following example creates an NAI realm profile:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# hotspot anqp-nai-realm-profile home
AP)(nai-realm "home")# nai-realm-name home-hotspot.com
AP)(nai-realm "home")# nai-realm-encoding utf8
AP)(nai-realm "home")# nai-realm-eap-method eap-sim
AP)(nai-realm "home")# nai-realm-auth-id-1 non-eap-inner-auth
AP)(nai-realm "home")# nai-realm-auth-value-1 mschapv2
AP)(nai-realm "home")# nai-home-realm
AP)(nai-realm "home")# enable
AP)(nai-realm "home")# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and the NAI realm profile configuration submode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
hotspot anqp-nai-realm-profile | 97
hotspot anqp-nwk-auth-profile
hotspot anqp-nwk-auth-profile <profile-name>
enable
nwk-auth-type <auth-type>
url <url>
no…
Description
This command configures an ANQP network authentication profile to define authentication type being used by the
hotspot network.
Syntax
Parameter
Description
Range
hotspot anqp-nwk-auth-profile
<profile-name>
Configures an ANQP network authentication
profile.
—
enable
Enables the network authentication profile.
—
nwk-auth-type
Defines the network Authentication type being
used by the hotspot network.
—
<auth-type>
Allows you to specify any of the following values:
accept-termand-cond,
onlineenrollment,
http-redirect,
dns-redirect
accept-term-and-cond—When configured, the
network requires the user to accept terms and
conditions.
NOTE: This option requires you to specify a
redirection URL string as an IP address, FQDN
or URL.
l online-enrollment—When configured, the
network supports the online enrollment.
l http-redirect—When configured, additional
information on the network is provided
through HTTP/HTTPS redirection.
l dns-redirect—When configured, additional
information on the network is provided
through DNS redirection.
NOTE: This option requires you to specify a
redirection URL string as an IP address, FQDN
or URL.
l
url
Configures URL, IP address, or FQDN used by
the hotspot network for the accept-term-andcond or dns-redirect network authentication
types.
—
no…
Removes any existing configuration.
—
Usage Guidelines
When the asra option is enabled in the hotspot profile associated with a WLAN SSID, the settings configured for the
network authentication profile are sent in the GAS response to the client.
Example
The following command configures a network authentication profile for DNS redirection.
(Instant AP)(config)# hotspot anqp-nwk-auth-profile default
98 | hotspot anqp-nwk-auth-profile
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(network-auth "default")#
AP)(network-auth "default")#
AP)(network-auth "default")#
AP)(network-auth "default")#
AP)# commit apply
nwk-auth-type dns-redirection
url http://www.example.com
enable
end
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and the ANQP network authentication profile
configuration sub-mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
hotspot anqp-nwk-auth-profile | 99
hotspot anqp-roam-cons-profile
hotspot anqp-roam-cons-profile <profile-name>
enable
roam-cons-oi <roam-cons-oi>
roam-cons-oi-len <roam-cons-oi-len>
no…
Description
This command configures the Roaming Consortium Organization Identifier (OI) information to be sent in an Access
network Query Protocol (ANQP) information element in a Generic Advertisement Service (GAS) query response.
Syntax
Parameter
Description
Range
hotspot anqp-roam-cons-profile
<profile-name>
Creates roaming consortium profile.
—
enable
Enables the roaming consortium profile.
—
roam-cons-oi
<roam-cons-oi>
Sends the specified roaming consortium OI in
a GAS query response. The OI must be a
hexadecimal number 3-5 octets in length.
Hexadecimal
number 3-5
octets in length
roam-cons-oi-len
<roam-cons-oi-len>
Indicates the length of the OI. The value of the
roam-cons-oi-len parameter must equal upon
the number of octets of the roam-cons-oi field.
l 0: 0 Octets in the OI (Null)
l 3: OI length is 24-bit (3 Octets)
l 5: OI length is 36-bit (5 Octets)
—
no…
Removes any existing configuration.
—
Usage Guidelines
Use this command to configure the roaming consortium OIs assigned to service providers when they register with
the IEEE registration authority. The Roaming Consortium Information Elements (IEs) contain information about the
network and service provider, whose security credentials can be used to authenticate with the W-IAP transmitting
this IE.
Example
The following command defines the roaming consortium OI and OI length in the ANQP roaming consortium profile:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# hotspot anqp-roam-cons-profile profile1
AP)(roaming-consortium "profile1")# roam-cons-oi 506F9A
AP)(roaming-consortium "profile1")# roam-cons-oi-len 3
AP)(roaming-consortium "profile1")# enable
AP)(roaming-consortium "profile1")# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
100 | hotspot anqp-roam-cons-profile
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and the ANQP roaming consortium profile
configuration sub-mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
hotspot anqp-roam-cons-profile | 101
hotspot anqp-venue-name-profile
hotspot anqp-venue-name-profile <profile-name>
enable
venue-group <group>
venue-lang-code <language>
venue-name <name>
venue-type <type>
no…
Description
This command defines venue information be sent in an Access network Query Protocol (ANQP) information element
in a Generic Advertisement Service (GAS) query response.
Syntax
Parameter
Description
Range
Default
hotspot anqpvenue-nameprofile
<profile-name>
Creates a ANQP venue
name profile.
—
—
enable
Enables the ANQP venue
name profile.
—
—
venue-group
<group>
Configures one of the
following venue groups to
be advertised in the IEs
from APs associated with
this hotspot profile.
l assembly
l business
l educational
l factory-and-industrial
l institutional
l mercantile
l outdoor
l residential
l storage
l utility-and-misc
l vehicular
NOTE: This parameter
only defines the venue
group advertised in the IEs
from hotspot APs. To
define the venue group to
be included in ANQP
responses, use anqpvenue-name-profile
<profile-name> command.
assembly, business,
educational,
factory-and-industrial,
institutional,
mercantile,
outdoor,
residential,
storage,
unspecified,
utility-and-misc,
vehicular
unspecified
venue-lang-code
<language>
Configures an ISO 639
language code that
identifies the language
used in the Venue Name
field.
—
—
102 | hotspot anqp-venue-name-profile
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Parameter
Description
Range
Default
venue-name
<name>
Configures the venue
name to be advertised in
the ANQP IEs. If the venue
name includes spaces, the
name must be enclosed in
quotation marks, e.g.
“Midtown Shopping
Center”.
—
—
venue-type
<type>
Specifies the venue type to
be advertised in the IEs.
The complete list of
supported venue types
is described in hotspot
anqp-venue-nameprofile on page 102.
unspecified
no…
Removes any existing
configuration.
—
—
Usage Guidelines
Use this command to configure the venue group and venue type in an ANQP Venue Name profile. If a client uses the
Generic Advertisement Service (GAS) to post an ANQP query to an Access Point, the W-IAP will return ANQP
Information Elements with the values configured in this profile.
Venue Types
The following list describes the different venue types for each venue group:
Venue Group
Associated Venue Type Value
assembly
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
business
l
l
l
l
l
l
l
l
l
arena
stadium
passenger-terminal
amphitheater
amusement-park
place-of-worship
convention-center
library
museum
restaurant
theater
bar
coffee-shop
zoo-or-aquarium
emergency-cord-center
unspecified
doctor
bank
fire-station
police-station
post-office
professional-office
research-and-dev-facility
attorney-office
unspecified
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
hotspot anqp-venue-name-profile | 103
Venue Group
Associated Venue Type Value
educational
l
l
l
l
factory-and-industrial
l
l
institutional
l
l
l
l
l
l
mercantile
l
l
l
l
l
l
outdoor
l
l
l
l
l
l
l
residential
l
l
l
l
l
school-primary
school-secondary
univ-or-college
unspecified
factory
unspecified
hospital
long-term-care
alc-drug-rehab
group-home
prison-or-jail
unspecified
retail-store
grocery-market
auto-service-station
shopping-mall
gas-station
unspecified
muni-mesh-network
city-park
rest-area
traffic-control
bus-stop
kisok
unspecified
private-residence
hotel
dormitory
boarding-house
unspecified
storage
unspecified
utility-and-misc
unspecified
vehicular
l
l
l
l
l
l
l
l
unspecified
automobile-or-truck
airplane
bus
ferry
ship
train
motor-bike
Example
The following command defines an ANQP Venue Name profile for a shopping mall:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# hotspot anqp-venue-name-profile Mall1
AP)(venue-name "Mall1")# venue-name ShoppingCenter1
AP)(venue-name "Mall1")# venue-group mercantile
AP)(venue-name "Mall1")# venue-type shopping-mall
AP)(venue-name "Mall1")# venue-lang-code EN
AP)(venue-name "Mall1")# enable
104 | hotspot anqp-venue-name-profile
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
(Instant AP)(venue-name "Mall1")# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and the ANQP venue name profile
configuration sub-mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
hotspot anqp-venue-name-profile | 105
hotspot h2qp-conn-cap-profile
hotspot h2qp-conn-cap-profile <profile-name>
enable
esp-port
icmp
tcp-ftp
tcp-http
tcp-pptp-vpn
tcp-ssh
tcp-tls-vpn
tcp-voip
udp-ike2
udp-ipsec-vpn
udp-voip
no…
Description
This command configures a Hotspot 2.0 Query Protocol (H2QP) profile that advertises hotspot protocol and port
capabilities.
Syntax
Parameter
Description
hotspot h2qp-conn-capprofile<profile-name>
Creates a connection capability profile.
enable
Enables the connection capability H2QP profile.
esp-port
Enables the Encapsulating Security Payload (ESP) port used by IPSec
VPNs. (port 0)
icmp
Indicates that the ICMP port is enabled and available. (port 0)
tcp-ftp
Enables the FTP port. (port 20)
tcp-http
Enables the HTTP port. (port 80)
tcp-pptp-vpn
Enables the PPTP port used by IPSec VPNs. (port 1723)
tcp-ssh
Enables the SSH port. (port 22)
tcp-tls-vpn
Enables the TCP TLS port used by VPNs. (port 80)
tcp-voip
Enables the TCP VoIP port. (port 5060)
udp-ike2
Enables the IKEv2 port.
udp-ipsec-vpn
Enables the IPsec VPN port. (ports 500, 4500 and 0)
udp-voip
Enables the UDP VoIP port. (port 5060)
no…
Removes any existing configuration.
106 | hotspot h2qp-conn-cap-profile
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Usage Guidelines
Use this command to configure the values to be sent in an ANQP IE to provide information about the IP protocols
and associated port numbers that are available and open for communication.
Example
The following example allows the H2QP connection capability profile to advertise the availability of ICMP and HTTP
ports.
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config) # hotspot h2qp-conn-cap-profile Wan1
AP)(connection-capabilities "Wan1")# icmp
AP)(connection-capabilities "Wan1")# tcp-http
AP)(connection-capabilities "Wan1")# enable
AP)(connection-capabilities "Wan1")# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and the H2QP connection capability profile
configuration sub-mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
hotspot h2qp-conn-cap-profile | 107
hotspot h2qp-oper-name-profile
hotspot h2qp-oper-name-profile <profile>
enable
op-fr-name <name>
op-lang-code <language>
no…
Description
This command configures a Hotspot 2.0 Query Protocol (H2QP) operator-friendly name profile.
Syntax
Parameter
Description
Range
Default
hotspot h2qp-oper-nameprofile <profile>
Creates an operator-friendly name profile.
—
—
enable
Enables the operator-friendly name profile.
—
—
op-fr-name
<name>
Configures an operator-friendly name to be sent by
devices using this profile. If the name includes
quotation marks (“), include a backslash character (\)
before each quotation mark. (e.g. \"example\")
1-64
alphanumeric
characters
—
op-lang-code <language>
Configures an ISO 639 language code that identifies
the language used in the op-fr-name command.
—
—
no…
Removes any existing configuration.
—
—
Usage Guidelines
Use this command to configure an operator-friendly name that can identify the operator and also provides information
about the location.
Example
The following example configures an operator friendly profile:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# hotspot h2qp-oper-name-profile Profile1
AP)(operator-friendly-name "Profile1")# op-fr-name hotspot1
AP)(operator-friendly-name "Profile1")# op-lang-code EN
AP)(operator-friendly-name "Profile1")# enable
AP)(operator-friendly-name "Profile1")# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
108 | hotspot h2qp-oper-name-profile
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and the H2QP operator friendly name profile
configuration sub-mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
hotspot h2qp-oper-name-profile | 109
hotspot h2qp-oper-class-profile
hotspot h2qp-oper-class-profile <profile>
enable
op-class <class>
no…
Description
This command configures a Hotspot 2.0 Query Protocol (H2QP) profile that defines the Operating Class to be sent in
the H2QP IE.
Syntax
Parameter
Description
Range
Default
hotspot h2qp-operclass-profile
<profile>
Creates operating class profile.
—
—
enable
Enables the operating class profile.
—
—
op-class <class>
Configures the operating class for the
devices’ BSS.
1-255
1
no…
Removes any existing configuration.
—
—
Usage Guidelines
Use this command to configure values for the H2QP Operating Class profile that lists the channels on which the
hotspot is capable of operating.
Example
The following example configures and enables a profile with the default operating class value.
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config) # hotspot h2qp-oper-class-profile Profile1
AP)(operator-class"Profile1")# op-class 1
AP)(operator-class"Profile1")# enable
AP)(operator-class"Profile1")# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and the H2QP operating class profile
configuration sub-mode
110 | hotspot h2qp-oper-class-profile
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
hotspot h2qp-wan-metrics-profile
hotspot h2qp-wan-metrics-profile <profile-name>
at-capacity
downlink-load <load>
downlink-speed <speed>
enable
load-duration <duration>
symm-link
uplink-load <load>
uplink-speed <speed>
wan-metrics-link-status <status>
no…
Description
This command configures a Hotspot 2.0 Query Protocol (H2QP) profile that specifies the hotspot WAN status and
link metrics.
Syntax
Parameter
Description
Range
Default
hotspot h2qp-wanmetrics-profile
<profile-name>
Creates a H2QP WAN metric profile
—
—
at-capacity
Indicates if the WAN Link has reached its
maximum capacity. If this parameter is enabled,
no additional mobile devices will be permitted to
associate to the hotspot W-IAP.
—
—
downlink-load
<load>
Configures the percentage of the WAN downlink
that is currently utilized. If no value is set, this
parameter will show a default value of 0 to
indicate that the downlink speed is unknown or
unspecified.
1-100
0
(unspecified)
downlink-speed
<speed>
Indicates the current WAN backhaul downlink
speed in Kbps. If no value is set, this parameter
will show a default value of 0 to indicate that the
downlink speed is unknown or unspecified.
02,147,483,64
7 Kbps
0
(unspecified)
enable
Enables the H2QP WAN metrics profile.
—
—
load-duration
<duration>
Configures a duration at which the downlink load
is measured, in tenths of a second.
0 and 65535
—
symm-link
Indicates that the WAN Link has same speed in
both the uplink and downlink directions.
—
—
no
Removes any existing configuration.
—
—
uplink-load <speed>
The percentage of the WAN uplink that is
currently utilized. If no value is set, this parameter
will show a default value of 0 to indicate that the
downlink speed is unknown or unspecified.
1-100
0
(unspecified)
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
hotspot h2qp-wan-metrics-profile | 111
Parameter
Description
Range
Default
uplink-speed
<speed>
Use the uplink <speed> parameter to indicate the
current WAN backhaul uplink speed in Kbps. If no
value is set, this parameter will show a default
value of 0 to indicate that the uplink speed is
unknown or unspecified.
02,147,483,64
7 kbps
0
(unspecified)
wan-metrics-linkstatus
Define the status of the WAN Link by configuring
one of the following values.
—
—
<status>
Configures any of the following states:
link-down,
link-undertest, link-up
unspecified
l
l
l
link-up— Indicates if WAN link is up.
link-down— Indicates if WAN link is down
link-under-test—Indicates if WAN link is
currently in a test state.
Usage Guidelines
Use this command to configure the values be sent in an H2QP IE to provide information about access network
characteristics such as link status and the capacity and speed of the WAN link to the Internet.
Examples
The following example configures a WAN metric profile:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# hotspot h2qp-wan-metrics-profile Wan1
AP)(WAN-metrics "Wan1")# at-capacity
AP)(WAN-metrics "Wan1")# downlink-load 5
AP)(WAN-metrics "Wan1")# downlink-speed 147
AP)(WAN-metrics "Wan1")# load-duration 60
AP)(WAN-metrics "Wan1")# symm-link
AP)(WAN-metrics "Wan1")# uplink-load 10
AP)(WAN-metrics "Wan1")# uplink-speed 147
AP)(WAN-metrics "Wan1")# wan-metrics-link-status link_up
AP)(WAN-metrics "Wan1")# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and the H2QP WAN metrics profile
configuration sub-mode
112 | hotspot h2qp-wan-metrics-profile
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
hotspot hs-profile
hotspot hs-profile <profile-name>
access-network-type <type>
addtl-roam-cons-ois <addtl-roam-cons-ois>
advertisement-profile {anqp-3gpp|anqp-domain-name|anqp-ip-addr-avail|anqp-nai-realm| anqpnwk-auth|anqp-roam-cons|anqp-venue-name|h2qp-conn-cap|h2qp-oper-class|h2qp-oper-name|h2qpwan-metrics} <profile-name>
advertisement-protocol <protocol>
asra
comeback-mode
enable
gas-comeback-delay <delay>
group-frame-block
hessid <id>
internet
no
p2p-cross-connect
p2p-dev-mgmt
pame-bi
query-response-length-limit <len>
roam-cons-len-1 0|3|5
roam-cons-len-2 0|3|5
roam-cons-len-3 0|3|5
roam-cons-oi-1 <roam-cons-oi-1>
roam-cons-oi-2 <roam-cons-oi-1>
roam-cons-oi-3 <roam-cons-oi-1>
venue-group <venue-group>
venue-type <venue-type>
Description
This command configures a hotspot profile for an 802.11u public access service provider.
Syntax
Parameter
Description
Range
Default
access-network-type <type>
Configures any of the following
access network (802.11u network
type) type:
l private — This network is
accessible for authorized users
only. For example, home
networks or enterprise
networks that require user
authentication. The
corresponding integer value for
this network type is 0.
l private-with-guest — This
network is accessible to guest
users based on guest
authentication methods. For
example, enterprise networks
that allow guest users with
captive portal authentication.
The corresponding integer
value for this network type is 1.
l chargeable-public — This
network provides access to the
private, privatewithguest,chargeabl
e-public, freepublic, personaldevice,
emergencyservices, test,
wildcard
chargeablepublic
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
hotspot hs-profile | 113
Parameter
Description
l
l
l
l
l
Range
Default
Internet based on payment. For
example, a subscription-based
Internet access in a coffee shop
or a hotel offering chargeable
in-room Internet access service.
The corresponding integer
value for this network type is 2.
free-public —This network is
accessible to all without any
charges applied. For example,
a hotspot in airport or other
public places that provide
Internet access with no
additional cost. The
corresponding integer value for
this network type is 3.
personal-device — This network
is accessible for personal
devices. For example, a laptop
or camera configured with a
printer for the purpose of
printing. The corresponding
integer value for this network
type is 4.
emergency-services —This
network is limited to accessing
emergency services only. The
corresponding integer value for
this network type is 5.
test — This network is used for
test purposes only. The
corresponding integer value for
this network type is 14.
wildcard —This network
indicates a wildcard network.
The corresponding integer
value for this network type is
15.
addtl-roam-cons-ois
<addtl-roam-cons-ois>
Configures the number of
additional roaming consortium
Organization Identifiers (OIs)
advertised by the AP. This feature
supports up to three additional OIs,
which are defined using the roamcons-oi-1, roam-cons-oi-2 and
roam-cons-oi-3 parameters.
—
—
advertisement-profile
{anqp-3gpp|
anqp-domain-name|
anqp-ip-addr-avail|
anqp-nai-realm|
anqp-nwk-auth|
anqp-roam-cons|
anqp-venue-name|
h2qp-conn-cap|
h2qp-oper-class|
h2qp-oper-name|
Associates an advertisement
profile with the hotspot profile.
You can associate any of the
following advertisement profiles:
l anqp-3gpp
l anqp-domain-name
l anqp-ip-addr-avail
l anqp-nai-realm
l anqp-nwk-auth
l anqp-roam-cons
l anqp-venue-name
—
—
114 | hotspot hs-profile
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Parameter
Description
h2qp-wan-metrics}
l
l
l
l
Range
Default
h2qp-conn-cap
h2qp-oper-class
h2qp-oper-name
h2qp-wan-metrics
<profile-name>
Allows you to associate a specific
advertisement profile to the hotspot
profile.
—
—
advertisement-protocol
<protocol>
Configures the anqp: Access
Network Query Protocol (ANQP)
advertisement protocol.
anqp
—
asra
Indicates if any additional steps are
required for network access.
—
—
comeback-mode
By default, ANQP information is
obtained from a GAS Request and
Response. If you enable the
comeback-mode option,
advertisement information is
obtained using a GAS Request
and Response. as well as a
Comeback-Request and
Comeback-Response. This option
is disabled by default.
—
—
enable
Enables the hotspot profile.
—
—
gas-comeback-delay
<delay>
Configures a GAS comeback delay
interval after which the client can
attempt to retrieve the query
response using a Comeback
Request Action frame.
100—2000
milliseconds
500
group-frame-block
Configures the Downstream Group
Addressed Forwarding (DGAF)
Disabled Mode. This feature
ensures that the W-IAP does not
forward downstream groupaddressed frames. It is disabled by
default, allowing the W-IAP to
forward downstream groupaddressed frames.
—
—
hessid
Configures a homogenous ESS
identifier (HESSSID)
MAC address in
colon-separated
hexadecimal
format
—
internet
Allows the W-IAP to send an
Information Element (IE) indicating
that the network allows the Internet
access. By default, a hotspot profile
does not advertise network internet
access.
—
—
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
hotspot hs-profile | 115
Parameter
Description
Range
Default
no
Removes any existing
configuration.
—
—
p2p-cross-connect
Advertises support for P2P Cross
Connections.
—
Disabled
p2p-dev-mgmt
Advertises support for P2P device
management.
—
Disabled
pame-bi
Enables the Pre-Association
Message Exchange BSSID
Independent (PAME-BI) bit, which
is used by an AP to indicate
whether the AP indicates that the
Advertisement Server can return a
query response that is
independent of the BSSID used for
the GAS Frame exchange.
—
—
query-response-lengthlimit
<len>
Configures the maximum length of
the Generic Advertisement Service
(GAS query response. GAS
enables advertisement services
that allow the clients to query
multiple 802.11 networks at once,
while also allowing the client to
learn more about a network’s
802.11 infrastructure before
associating.
If a client transmits a GAS Query
using a GAS Initial Request frame,
the responding W-IAP will provide
the query response (or information
on how to receive the query
response) in a GAS Initial
Response frame.
1-127
127
roam-cons-len-1
Configures the length of the OI.
The value of the roam-cons-len1parameter is based upon the
number of octets of the roam-consoi-1 field.
0: Zero Octets in
the OI (Null),
3: OI length is
24-bit (3 Octets),
5: OI length is
36-bit (5 Octets)
—
roam-cons-len-2
Length of the OI. The value of the
roam-cons-len-2parameter is
based upon the number of octets of
the roam-cons-oi-2 field.
0: Zero Octets in
the OI (Null),
—
Length of the OI. The value of the
roam-cons-len-3parameter is
based upon the number of octets of
the roam-cons-oi-3 field.
0: Zero Octets in
the OI (Null),
3: OI length is
24-bit (3 Octets),
5: OI length is
36-bit (5 Octets)
roam-cons-len-3
116 | hotspot hs-profile
3: OI length is
24-bit (3 Octets),
5: OI length is
36-bit (5 Octets)
—
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Parameter
Description
Range
Default
roam-cons-oi-1
roam-cons-oi-2
roam-cons-oi-3
Configures the roaming consortium
OI to assign to one of the service
provider’s top three roaming
partners. This additional OI will
only be sent to a client if the addtlroam-cons-<oisaddtl-roam-consois> parameter is set to 1 or higher.
NOTE: The service provider’s own
roaming consortium OI is
configured using the hotspot anqproam-cons-profile command.
—
—
venue-group <venue-group>
Configures one of the following
venue groups to be advertised in
the IEs from APs associated with
this hotspot profile.
l assembly
l business
l educational
l factory-and-industrial
l institutional
l mercantile
l outdoor
l residential
l storage
l unspecified
l utility-and-misc
l vehicular
NOTE: This parameter only
defines the venue group
advertised in the IEs from hotspot
APs. To define the venue group to
be included in ANQP responses,
use anqp-venue-name-profile
<profile-name> command.
assembly,
business,
educational,
factory-andindustrial,
institutional,
mercantile,
outdoor,
residential,
storage,
unspecified,
utility-and-misc,
vehicular
business
venue-type <venue-type>
Specifies the venue type to be
advertised in the IEs from APs
associated with this hotspot profile.
The complete list of supported
venue types is described in Venue
Types on page 119
NOTE: This parameter only
defines the venue type advertised
in the IEs from hotspot APs. To
define the venue type to be
included in ANQP responses, use
the hotspot anqp-venue-nameprofile <profile-name> command.
—
—
Usage Guidelines
Use this command to configure a hotspot profile. Hotspot 2.0 is a Wi-Fi Alliance specification based on the 802.11u
protocol, which allows wireless clients to discover hotspots using management frames (such as beacon,
association request and association response), connect to networks, and roam between networks without additional
authentication.
The Hotspot 2.0 provides the following services:
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
hotspot hs-profile | 117
l
Network discovery and selection— Allows the clients to discover suitable and available networks by advertising
the access network type, roaming consortium, and venue information through the management frames. For
network discovery and selection, Generic Advertisement Service (GAS) and Access Network Query Protocol
(ANQP) are used.
l
QOS Mapping— Provides a mapping between the network-layer QoS packet marking and over- the-air QoS frame
marking based on user priority.
When a hotspot is configured in a network:
l
The clients search for available hotspots using the beacon management frame.
l
When a hotspot is found, the client sends queries to obtain information about the type of network authentication
and IP address, and IP address availability using the Generic Advertisement Service (GAS) action frames.
l
Based on the response of the advertisement Server (response to the GAS Action Frames), the relevant hotspot is
selected and the client attempts to associate with it.
l
Based on the authentication mode used for mobility clients, the client authenticates to access the network.
Generic Advertisement Service (GAS) Queries
An Organization Identifier (OI) is a unique identifier assigned to a service provider when it registers with the IEEE
registration authority. A W-IAP can include its service provider OI in beacons and probe responses to clients. If a
client recognizes the OI, it will attempt to associate to the W-IAP using the security credentials corresponding to that
service provider.
If the client does not recognize the OI, that client can send a Generic Advertisement Service (GAS) query to the AP
to request more information more about the network before associating.
ANQP Information Elements
ANQP Information Elements (IEs) are additional data that can be sent from the AP to the client to identify the AP’s
network and service provider. If a client requests this information via a GAS query, the hotspot AP then sends the
ANQP Capability list in the GAS Initial Response frame indicating support for the following IEs:
l
Venue Name - Defined using the hotspot anqp-venue-name-profile command.
l
Domain Name: Defined using the hotspot anqp-domain-name-profile command.
l
Network Authentication Type: Define using the hotspot anqp-nwk-auth-profile command.
l
Roaming Consortium List: Defined using the hotspot anqp-roam-cons-profile command.
l
NAI Realm: Defined using the hotspot anqp-nai-realm-profile command.
l
Cellular Network Data: Defined using the hotspot anqp-3gpp-nwk-profile command.
l
Connection Capability: Defined using the hotspot h2qp-conn-capability-profile command.
l
Operator Class: Defined using the hotspot h2qp-op-cl-profile command.
l
Operator Friendly Name: Defined using the hotspot h2qp-operator-friendly-name-profile command.
l
WAN Metrics: Defined using the hotspot h2qp-wan-metrics-profile command.
Roaming Consortium OIs
Organization Identifiers (OIs) are assigned to service providers when they register with the IEEE registration
authority. You can specify the OI for the hotspot’s service provider in the ANQP Roaming Consortium profile using
the hotspot anqp-roam-cons-profile command. This Hotspot profile also allows you to define and send up to three
additional roaming consortium OIs for the service provider’s top three roaming partners. To send this additional data
to clients, you must specify the number of roaming consortium elements a client can query using the addtl-roamcons-ois <1-3> parameter, then define those elements using the following parameters:
l
roam-cons-oi-1 and roam-cons-len 1
l
roam-cons-oi-2 and roam-cons-len 2
118 | hotspot hs-profile
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
l
roam-cons-oi-3 and roam-cons-len 3
The configurable values for each additional OI include the Organization Identifier itself, the OI length, and the venue
group and venue type associated with those OIs.
Venue Types
The following list describes the different venue types for each venue group:
Table 10: Venue Types
Venue Group
Associated Venue Type Value
unspecified
—
The associated numeric value is 0.
assembly
The associated numeric value is 1.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
business
The associated numeric value is 2.
l
l
l
l
l
l
l
l
l
educational
The associated numeric value is 3.
l
l
l
l
factory-and-industrial
The associated numeric value is 4.
institutional
The associated numeric value is 5.
l
l
unspecified—The associated numeric value is 0.
doctor—The associated numeric value is 1
bank—The associated numeric value is 2
fire-station—The associated numeric value is 3
police-station—The associated numeric value is 4
post-office—The associated numeric value is 6
professional-office—The associated numeric value is 7
research-and-dev-facility—The associated numeric value is 8
attorney-office—The associated numeric value is 9
unspecified—The associated numeric value is 0.
school-primary—The associated numeric value is 1.
school-secondary—The associated numeric value is 2.
univ-or-college—The associated numeric value is 3.
unspecified—The associated numeric value is 0.
factory—The associated numeric value is 1.
l
unspecified—The associated numeric value is 0.
hospital—The associated numeric value is 1.
long-term-care—The associated numeric value is 2.
alc-drug-rehab—The associated numeric value is 3.
group-home—The associated numeric value is 4.
prison-or-jail—The associated numeric value is 5.
l
unspecified—The associated numeric value is 0.
l
l
l
l
l
mercantile
unspecified—The associated numeric value is 0.
arena—The associated numeric value is 1.
stadium—The associated numeric value is 2.
passenger-terminal—The associated numeric value is 3.
amphitheater—The associated numeric value is 4.
amusement-park—The associated numeric value is 5.
place-of-worship—The associated numeric value is 6.
convention-center—The associated numeric value is 7.
library—The associated numeric value is 8.
museum—The associated numeric value is 9.
restaurant—The associated numeric value is 10.
theater—The associated numeric value is 11.
bar —The associated numeric value is 12.
coffee-shop —The associated numeric value is 13.
zoo-or-aquarium —The associated numeric value is 14.
emergency-cord-center—The associated numeric value is 15.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
hotspot hs-profile | 119
Venue Group
Associated Venue Type Value
The associated numeric value is 6.
l
l
l
l
l
residential
The associated numeric value is 7.
l
l
l
l
l
retail-store—The associated numeric value is 1.
grocery-market—The associated numeric value is 2.
auto-service-station—The associated numeric value is 3.
shopping-mall—The associated numeric value is 4.
gas-station—The associated numeric value is 5
unspecified—The associated numeric value is 0.
private-residence—The associated numeric value is 1.
hotel—The associated numeric value is 3
dormitory—The associated numeric value is 4
boarding-house—The associated numeric value is 5.
storage
The associated numeric value is 8.
unspecified—The associated numeric value is 0.
utility-misc
unspecified—The associated numeric value is 0.
The associated numeric value is 9.
vehicular
l
The associated numeric value is 10
l
l
l
l
l
l
l
outdoor
l
The associated numeric value is 11.
l
l
l
l
l
l
unspecified—The associated numeric value is 0.
automobile-or-truck—The associated numeric value is 1.
airplane—The associated numeric value is 2.
bus—The associated numeric value is 3.
ferry—The associated numeric value is 4.
ship —The associated numeric value is 5.
train —The associated numeric value is 6.
motor-bike—The associated numeric value is 7.
unspecified—The associated numeric value is 0
muni-mesh-network—The associated numeric value is 1.
city-park—The associated numeric value is 2.
rest-area—The associated numeric value is 3.
traffic-control—The associated numeric value is 4
bus-stop—The associated numeric value is 5
kiosk —The associated numeric value is 6
Example
The following commands configure a hotspot profile:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
120 | hotspot hs-profile
AP)(config)# hotspot hs-profile hs1
AP)(Hotspot2.0 "hs1")# enable
AP)(Hotspot2.0 "hs1")# comeback-mode
AP)(Hotspot2.0 "hs1")# gas-comeback-delay 10
AP)(Hotspot2.0 "hs1")# no asra
AP)(Hotspot2.0 "hs1")# no internet
AP)(Hotspot2.0 "hs1")# query-response-length-limit 127
AP)(Hotspot2.0 "hs1")# access-network-type chargeable-public
AP)(Hotspot2.0 "hs1")# roam-cons-len-1 3
AP)(Hotspot2.0 "hs1")# roam-cons-oi-1 123456
AP)(Hotspot2.0 "hs1")# roam-cons-len-2 3
AP)(Hotspot2.0 "hs1")# roam-cons-oi-2 223355
AP)(Hotspot2.0 "hs1")# addtl-roam-cons-ois 0
AP)(Hotspot2.0 "hs1")# venue-group business
AP)(Hotspot2.0 "hs1")# venue-type research-and-dev-facility
AP)(Hotspot2.0 "hs1")# pame-bi
AP)(Hotspot2.0 "hs1")# group-frame-block
AP)(Hotspot2.0 "hs1")# p2p-dev-mgmt
AP)(Hotspot2.0 "hs1")# p2p-cross-connect
AP)(Hotspot2.0 "hs1")# end
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
(Instant AP)# commit apply
The following commands associate anqp-3gpp advertisement profile with a hotspot profile:
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# hotspot hs-profile hs1
AP)(Hotspot2.0"hs1")# advertisement-protocol anpp
AP)(Hotspot2.0"hs1")# advertisement-profile anqp-3gpp 3gpp1
AP)(Hotspot2.0"hs1")# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and the hotspot profile configuration submode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
hotspot hs-profile | 121
iap-master
iap-master
no…
Description
This command provisions a W-IAP as a master W-IAP.
Syntax
Command/Parameter
Description
iap-master
Provisions the W-IAP as a master W-IAP.
no…
Removes the configuration.
Usage Guidelines
Use this command to manually provision a W-IAP as a master W-IAP.
Example
The following example provisions a master IAP:
(Instant AP)# iap-master
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.14.0
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
122 | iap-master
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
ids
ids
client-detection-level <type>
client-protection-level <type>
detect-adhoc-network
detect-ap-flood
detect-ap-impersonation
detect-ap-spoofing
detect-bad-wep
detect-beacon-wrong-channel
detect-block-ack-attack
detect-chopchop-attack
detect-client-flood
detect-cts-rate-anomaly
detect-disconnect-sta
detect-eap-rate-anomaly
detect-fatajack
detect-hotspotter-attack
detect-ht-40mhz-intolerance
detect-ht-greenfield
detect-invalid-addresscombination
detect-invalid-mac-oui
detect-malformed-assoc-req
detect-malformed-frame-auth
detect-malformed-htie
detect-malformed-large-duration
detect-omerta-attack
detect-overflow-eapol-key
detect-overflow-ie
detect-power-save-dos-attack
detect-rate-anomalies
detect-rts-rate-anomaly
detect-tkip-replay-attack
detect-unencrypted-valid
detect-valid-clientmisassociation
detect-valid-ssid-misuse
detect-windows-bridge
detect-wireless-bridge
infrastructure-detection-level <type>
infrastructure-protection-level <type>
protect-adhoc-network
protect-ap-impersonation
protect-ssid
protect-valid-sta
protect-windows-bridge
rogue-containment
signature-airjack
signature-asleap
signature-deassociation-broadcast
signature-deauth-broadcast
wired-containment
wireless-containment <type>
no…
Description
This command configures an IDS policy for a W-IAP.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
ids | 123
Syntax
124 | ids
Parameter
Description
Range
Default
ids
Creates an IDS policy
—
—
client-detection-level
<type>
Sets the client detection level.
off, low,
medium, high
off
client-protection-level
<type>
Sets the client protection level.
off, low,
medium, high
off
detect-adhoc-network
Enables detection of adhoc networks.
—
—
detect-ap-flood
Enables detection of flooding with fake
W-IAP beacons to confuse the legitimate
users and to increase the amount of
processing needed on client operating
systems.
—
—
detect-ap-impersonation
Enables detection of AP impersonation.
In AP impersonation attacks, the attacker
sets up an AP that assumes the BSSID
and ESSID of a valid AP. AP
impersonation attacks can be done for
man-in-the-middle attacks, a rogue AP
attempting to bypass detection, or a
honeypot attack.
—
—
detect-ap-spoofing
Enables AP Spoofing detection.
—
—
detect-bad-wep
Enables detection of WEP initialization
vectors that are known to be weak and/or
repeating. A primary means of cracking
WEP keys is to capture 802.11 frames
over an extended period of time and
search for implementations that are still
used by many legacy devices.
—
—
detect-beacon-wrongchannel
Enables detection of beacons
advertising the incorrect channel.
—
—
detect-block-ack-attack
Enables detection of attempts to reset
traffic receive windows using the forged
Block ACK Add messages.
—
—
detect-chopchop-attack
Enables detection of ChopChop attack.
—
—
detect-client-flood
Enables detection of client flood attack.
—
—
detect-cts-rate-anomaly
Enables detection of CTS rate anomaly.
—
—
detect-disconnect-sta
Enables a station disconnection attack.
In a station disconnection, attacker
spoofs the MAC address of either an
active client or an active AP. The attacker
then sends deauthenticate frames to the
target device, causing it to lose its active
association.
—
—
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Parameter
Description
Range
Default
detect-eap-rate-anomaly
Enables Extensible Authentication
Protocol (EAP) handshake analysis to
detect an abnormal number of
authentication procedures on a channel
and generate an alarm when this
condition is detected.
—
—
detect-fatajack
Enables detection of fatjack attacks.
—
—
detect-hotspotter-attack
Enables detection of hotspot attacks.
—
—
detect-ht-40mhzintolerance
Enables detection of 802.11n 40 MHz
intolerance setting, which controls
whether stations and APs advertising 40
MHz intolerance will be reported.
—
—
detect-ht-greenfield
Enables detection of high throughput
devices advertising greenfield preamble
capability.
—
—
detect-invalidaddresscombination
Enables detection of invalid address
combinations.
—
—
detect-invalid-mac-oui
Enables checking of the first three bytes
of a MAC address, known as the
organizationally unique identifier (OUI),
assigned by the IEEE to known
manufacturers. Often clients using a
spoofed MAC address do not use a valid
OUI and instead use a randomly
generated MAC address. Enabling MAC
OUI checking causes an alarm to be
triggered if an unrecognized MAC
address is in use.
—
—
detect-malformed-assoc-req
Enables detection of malformed
association requests.
—
—
detect-malformed-frameauth
Enables detection of malformed
authentication frames
—
—
detect-malformed-htie
Enables detection of malformed HT
information elements.
—
—
detect-malformed-largeduration
Enables detection of unusually large
durations in frames.
—
—
detect-omerta-attack
Enables detection of Omerta attack.
—
—
detect-overflow-eapol-key
Enables detection of overflow EAPOL
key requests.
—
—
detect-overflow-ie
Enables detection of overflow
Information Elements (IE).
—
—
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
ids | 125
126 | ids
Parameter
Description
Range
Default
detect-power-save-dosattack
Enables detection of Power Save DoS
attack.
—
—
detect-rate-anomalies
Enables detection of rate anomalies.
—
—
detect-rts-rate-anomaly
Enables detection of RTS rate anomaly.
—
—
detect-tkip-replay-attack
Enables detection of TKIP replay attack.
—
—
detect-unencrypted-valid
Enables detection of unencrypted valid
clients.
—
—
detect-validclientmisassociation
Enables detection of misassociation
between a valid client and an unsafe AP.
This setting can detect the following
misassociation types:
l MisassociationToRogueAP
l MisassociationToExternalAPl
l MisassociationToHoneypotAP
l MisassociationToAdhocAP
l MisassociationToHostedAP
—
—
detect-valid-ssid-misuse
Enables detection of interfering or
Neighbor APs using valid or protected
SSIDs.
—
—
detect-windows-bridge
Enables detection of Windows station
bridging.
—
—
detect-wireless-bridge
Enables detection of wireless bridging.
—
—
infrastructure-detectionlevel <type>
Sets the infrastructure detection level.
off, low,
medium, high
off
infrastructure-protectionlevel <type>
Sets the infrastructure protection level.
off, low,
medium, high
off
protect-adhoc-network
Enables protection from adhoc networks.
When adhoc networks are detected,
they are disabled using a denial of
service attack
—
—
protect-ap-impersonation
Enables protection from AP
impersonation attacks. When AP
impersonation is detected, both the
legitimate and impersonating AP are
disabled using a denial of service attack.
—
—
protect-ssid
Enables use of SSID by valid W-IAPs
only.
—
—
protect-valid-sta
Enables protection of valid stations.
When enabled valid stations are not
allowed to connect to an invalid AP.
—
—
protect-windows-bridge
Enables protection of a windows station
—
—
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Parameter
Description
Range
Default
—
—
bridging
rogue-containment
Controls Rogue APs. When rogue APs
are detected, they are not automatically
disabled.
This option automatically shuts down
rogue APs. When this option is enabled,
clients attempting to associate to an AP
classified as a rogue are disconnected
through a denial of service attack.
signature-airjack
Enables signature matching for the
AirJack frame type.
—
—
signature-asleap
Enables signature matching for the
ASLEAP frame type.
—
—
signature-deassociationbroadcast
Configures signature matching for the
deassociation broadcast frame type.
—
—
signature-deauth-broadcast
Configures signature matching for the
deauth broadcast frame type.
—
—
wired-containment
Controls Wired attacks.
—
—
wireless-containment
<type>
Enable wireless containment including
Tarpit Shielding.
deauth-only,
none, tarpitall-sta, tarpitnon-valid-sta
deauth-only
—
—
Tarpit shielding works by steering a
client to a tarpit so that the client
associates with it instead of the AP that is
being contained.
l
l
l
l
no…
deauth-only— Enables Containment
using deauthentication only .
none— Disables wireless
containment.
tarpit-all-sta—Enables wireless
containment by tarpit of all stations.
tarpit-non-valid-sta— Enables
wireless containment by tarpit of nonvalid clients
Removes any existing configuration.
Usage Guidelines
Use this command to configure Intrusion Detection System (IDS) detection and protection policies. The IDS feature
monitors the network for the presence of unauthorized W-IAPs and clients and enables you to detect rogue APs,
interfering APs, and other devices that can potentially disrupt network operations. It also logs information about the
unauthorized W-IAPs and clients, and generates reports based on the logged information.
Wireless Intrusion Protection (WIP) offers a wide selection of intrusion detection and protection features to protect
the network against wireless threats. Like most other security-related features of the Dell network, the WIP can be
configured on the W-IAP.
You can configure the following policies:
l
Infrastructure Detection Policies— Specifies the policy for detecting wireless attacks on access points
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
ids | 127
l
Client Detection Policies— Specifies the policy for detecting wireless attacks on clients
l
Infrastructure Protection Policies— Specifies the policy for protecting access points from wireless attacks.
l
Client Protection Policies— Specifies the policy for protecting clients from wireless attacks.
l
Containment Methods— Prevents unauthorized stations from connecting to your Instant network.
Each of these options contains several default levels that enable different sets of policies. An administrator can
customize enable or disable these options accordingly. The following levels of detection can be configured:
l
Off
l
Low
l
Medium
l
High
Example
The following example configures detection and protection policies:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
128 | ids
AP)(config)# ids
AP)(IDS)# infrastructure-detection-level low
AP)(IDS)# client-detection-level low
AP)(IDS)# infrastructure-protection-level low
AP)(IDS)# client-protection-level low
AP)(IDS)# wireless-containment deauth-only
AP)(IDS)# wired-containment
AP)(IDS)# detect-ap-spoofing
AP)(IDS)# detect-windows-bridge
AP)(IDS)# signature-deauth-broadcast
AP)(IDS)# signature-deassociation-broadcast
AP)(IDS)# detect-adhoc-using-valid-ssid
AP)(IDS)# detect-malformed-large-duration
AP)(IDS)# detect-ap-impersonation
AP)(IDS)# detect-adhoc-network
AP)(IDS)# detect-valid-ssid-misuse
AP)(IDS)# detect-wireless-bridge
AP)(IDS)# detect-ht-40mhz-intolerance
AP)(IDS)# detect-ht-greenfield
AP)(IDS)# detect-ap-flood
AP)(IDS)# detect-client-flood
AP)(IDS)# detect-bad-wep
AP)(IDS)# detect-cts-rate-anomaly
AP)(IDS)# detect-rts-rate-anomaly
AP)(IDS)# detect-invalid-addresscombination
AP)(IDS)# detect-malformed-htie
AP)(IDS)# detect-malformed-assoc-req
AP)(IDS)# detect-malformed-frame-auth
AP)(IDS)# detect-overflow-ie
AP)(IDS)# detect-overflow-eapol-key
AP)(IDS)# detect-beacon-wrong-channel
AP)(IDS)# detect-invalid-mac-oui
AP)(IDS)# detect-valid-clientmisassociation
AP)(IDS)# detect-disconnect-sta
AP)(IDS)# detect-omerta-attack
AP)(IDS)# detect-fatajack
AP)(IDS)# detect-block-ack-attack
AP)(IDS)# detect-hotspotter-attack
AP)(IDS)# detect-unencrypted-valid
AP)(IDS)# detect-power-save-dos-attack
AP)(IDS)# detect-eap-rate-anomaly
AP)(IDS)# detect-rate-anomalies
AP)(IDS)# detect-chopchop-attack
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(IDS)# detect-tkip-replay-attack
AP)(IDS)# signature-airjack
AP)(IDS)# signature-asleap
AP)(IDS)# protect-ssid
AP)(IDS)# rogue-containment
AP)(IDS)# protect-adhoc-network
AP)(IDS)# protect-ap-impersonation
AP)(IDS)# protect-valid-sta
AP)(IDS)# protect-windows-bridge
AP)(IDS)# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and IDS configuration sub-mode.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
ids | 129
ignore-image-check
ignore-image-check
Description
This command ignores the automatic image check feature. The automatic image check feature automatically
checks for a new version of Instant on the image server, once after the AP boots up and every week thereafter.
Usage Guidelines
Use this command to disable the automatic image check feature:
Example
The following example disables the image check feature:
(Instant AP)# ignore-image-check
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.14.0
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
130 | ignore-image-check
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
inactivity-ap-timeout
inactivity-ap-timeout <seconds>
no…
Description
This command configures the timeout interval for inactive user sessions.
Syntax
Parameter
Description
Range
Default
inactivity-aptimeout
<seconds>
Configures the inactivity timeout interval in seconds.
1-1000
1000
no…
Removes any existing configuration.
—
—
Usage Guidelines
Use this command to configure an inactivity timeout interval for a W-IAP.
Example
The following example configures the inactivity timeout interval:
(Instant AP)(config)# inactivity-ap-timeout 180
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
inactivity-ap-timeout | 131
inbound-firewall
inbound-firewall
rule <subnet> <smask> <dest> <mask> <match/invert> <protocol> <sport> <eport>
{permit|deny|src-nat|dst-nat ip <IP-address> <port>}[<option1....option9>]
no…
Description
This command configures inbound firewall rules based on the source subnet.
Syntax
Command/Parameter
Description
Range
Default
inbound-firewall
Opens the inbound firewall configuration
mode.
—
—
rule
Creates an access rule.
—
—
You can create up to 128 access rules.
However, it is recommended to delete
any existing configuration and apply
changes at regular intervals.
<subnet>
Allows you to specify the source subnet
IP address
—
—
<smask>
Specifies the subnet mask of the source
IP address.
—
—
<dest>
Allows you to specify the destination IP
address.
—
—
<mask>
Specifies the subnet mask for the
destination IP address.
—
—
<match/invert>
l
match
—
l
match—Indicates if the rule specific to
the destination IP address and subnet
mask matches the value specified for
protocol.
invert— Indicates if the rule allows or
denies traffic with an exception to the
specified destination IP address and
subnet mask.
invert
Configures any of the following:
Protocol number between 0-255
l any: any protocol
l tcp: Transmission Control Protocol
l udp: User Datagram Protocol
1-255
—
<sport>
Specifies the starting port number from
which the rule applies.
1-65534
—
<eport>
Specifies the ending port number until
which the rule applies
1-65534
—
dst-nat
Allows the W-IAP to perform destination
—
—
<protocol>
l
132 | inbound-firewall
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command/Parameter
Description
Range
Default
NAT on packets.
src-nat
Allows the W-IAP to perform source NAT
on packets. When configured, the source
IP changes to the outgoing interface IP
address (implied NAT pool) or from the
pool configured (manual NAT pool).
—
—
ip <IP-addr>
Specifies the destination NAT IP address
for the specified packets when dst-nat
action is configured.
—
—
<port>
Specifies the destination NAT port for the
specified packets when dst-nat action is
configured.
—
—
deny
Creates a rule to reject the specified
packets
—
—
Allows you to specify any of the following
options:
—
—
—
—
<option1…option9>
l
l
l
l
l
l
no…
Log —Creates a log entry when this
rule is triggered.
Blacklist — Blacklists the client when
this rule is triggered.
Classify-media — Performs a packet
inspection on all non-NAT traffic and
marks the critical traffic.
Disable-scanning — Disables ARM
scanning when this rule is triggered.
DSCP tag — Specifies a DSCP value
to prioritize traffic when this rule is
triggered.
802.1p priority — Sets an 802.1p
priority.
Removes the configuration
Usage Guidelines
Use this command to configure inbound firewall rules for the inbound traffic coming through the uplink ports of a WIAP. The rules defined for the inbound traffic are applied if the destination is not a user connected to the W-IAP. If the
destination already has a user role assigned, the user role overrides the actions or options specified in inbound
firewall configuration. However, if a deny rule is defined for the inbound traffic, it is applied irrespective of the
destination and user role. Unlike the ACL rules in a WLAN SSID or wired profile, the inbound firewall rules can be
configured based on the source subnet.
For all subnets, a deny rule is created by default as the last rule. If at least one rule is configured, the deny all rule is
applied to the upstream traffic by default.
Management access to the AP is allowed irrespective of the inbound firewall rule. For more information on
configuring restricted management access, see restricted-mgmt-access.
The inbound firewall is not applied to traffic coming through GRE tunnel.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
inbound-firewall | 133
Example
The following example configures inbound firewall rules:
(Instant
(Instant
(Instant
(Instant
AP)(config)# inbound-firewall
AP)(inbound-firewall)# rule 192.0.2.1 255.255.255.255 any any match 6 631 631 permit
AP)(inbound-firewall)# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.4.0.24.1
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and inbound firewall configuration sub-mode.
134 | inbound-firewall
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
internal-domains
internal-domains
domain-name <domain-name>
no...
Description
This command configures valid domain names for the enterprise network.
Syntax
Parameter
Description
Range
Default
internal-domains
Enables the internal-domain configuration submode
—
—
domain-name <domainname>
Defines the valid domain names
—
—
no…
Removes any existing configuration
—
—
Usage Guidelines
Use this command to configure the DNS domain names that are valid on the enterprise network. This list is used for
determining how the client DNS requests should be routed. When Content Filtering is enabled, the DNS request of
the clients is verified and the domain names that do not match the names in the list are sent to the open DNS server.
Example
The following example configures the internal domains for a network:
(Instant
(Instant
(Instant
(Instant
AP)(config)# internal-domains
AP)(domain)# domain-name www.example.com
AP)(domain)# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and domains configuration sub-mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
internal-domains | 135
ip-address
ip-address <ip-address> <subnet-mask> <nexthop-ip-address> <dns-ip-address> <domain-name>
Description
This command configures an IP address for the W-IAP.
Syntax.
Parameter
Description
<ip-address>
Assigns an IP address to the W-IAP.
<subnet-mask>
Specifies the subnet mask.
<nexthop-ip-address>
Specifies the gateway IP address.
<dns-ip-address>
Specifies the DNS server IP address.
<domain-name>
Specifies the domain name.
Usage Guidelines
Use this command to assign a static IP address to the W-IAP.
Example
The following example configures an IP address for the W-IAP.
(Instant AP)# ip-address 192.0.2.0 255.255.255.0 192.0.2.3 192.0.2.2 example.com
Command History
Version
Description
Dell Networking WSeries Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
136 | ip-address
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
ip dhcp
ip dhcp <dhcp_profile>
bid <bid>
client-count <idx>
default-router <default_router>
dhcp-relay
dhcp-server <dhcp_server>
disable-split-tunnel
dns-server <dns_server>
domain-name <domain-name>
exclude-address <exclude_address>
host <mac>
ip-range <start_IP> <end_IP>
lease-time <lease_time>
option <option_type> <option_value>
option82 alu
reserve {first <count>| last <count>}
server-type <server_type>
server-vlan <idx>
subnet <subnet>
subnet-mask <Subnet-Mask>
vlan-ip <VLAN_IP> mask <VLAN mask>
no…
Description
This command configures DHCP assignment modes and scopes for Instant network.
Syntax
Parameter
Description
Range
Default
ip dhcp <profile>
Creates a DHCP profile with a unique
name.
—
—
bid <bid>
Defines the branch ID.
—
—
—
—
NOTE: You can allocate multiple
branch IDs (BID) per subnet. The W-IAP
generates a subnet name from the
DHCP IP configuration, which the
controller can use as a subnet identifier.
If static subnets are configured in each
branch, all of them are assigned the
with BID 0, which is mapped directly to
the configured static subnet.
client-count <idx>
Defines the number of clients allowed
per DHCP branch.
NOTE: The client count configured for a
branch determines the use of IP
addresses from the IP address range
defined for a DHCP scope. For
example, if 20 IP addresses are
available in an IP address range
configured for a DHCP scope and a
client count of 9 is configured, only a
few IP addresses (in this example, 9)
from this range will be used and
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
ip dhcp | 137
Parameter
Description
Range
Default
allocated to a branch. The W-IAP does
not allow the administrators to assign
the remaining IP addresses to another
branch, although a lower value is
configured for the client count.
default-router
<default_router>
Defines the IP address of the default
router for the Distributed, L2 DHCP
scope.
—
—
dhcp-relay
Enables the W-IAPs to intercept the
broadcast packets and relay DHCP
requests directly to corporate network.
—
—
The DHCP relay is enabled for the
centralized DHCP scopes to reduce
network traffic caused by the
broadcasting of DHCP requests to the
corporate network. With a centralized
DHCP scope, the clients in the branch
are in the same subnet as clients in the
corporate network. Normally the DHCP
request goes through the VPN tunnel
and is broadcast into the corporate
network. This feature allows it to
succeed without requiring to broadcast
and thus reduces the network traffic.
138 | ip dhcp
dhcp-server <dhcp_
server>
Defines the IP address of the corporate
DHCP server for DHCP request relay.
—
—
disable-splittunnel
Disables split tunnel functionality for
Centralized L2 subnets.
Split tunneling allows a VPN user to
access a public network and a local
LAN or WAN network at the same time
through the same physical network
connection.
When split-tunnel is disabled, all the
traffic including the corporate and
Internet traffic is tunneled irrespective of
the routing profile specifications. If the
GRE tunnel is down and when the
corporate network is not reachable, the
client traffic is dropped.
—
—
dns-server <IPaddress>
Defines the DNS server IP address.
—
—
domain-name
<domain-name>
Defines the domain name.
—
—
host <mac>
Allows you to specify the host MAC
address.
—
—
exclude-address
<exclude_address>
Defines the IP address to exclude for
the Local,L3 DHCP scope. The value
—
—
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Parameter
Description
Range
Default
—
—
entered in the field determines the
exclusion range of the subnet. Based on
the size of the subnet, the IP addresses
that come before or after the IP address
value specified in this field are
excluded.
ip-range <start_IP>
<end_IP>
Defines a range of IP addresses to use
in the distributed,l2 and distributed,l3
DHCP scopes. You can configure a
range of DHCP IP addresses used in
the branches and the number of client
addresses allowed per branch. You can
also specify the IP addresses that must
be excluded from those assigned to
clients, so that they are assigned
statically. You can configure up to four
different ranges of IP addresses
l
l
For Distributed,L2 mode, ensure
that all IP ranges are in the same
subnet as the default router. On
specifying the IP address ranges, a
subnet validation is performed to
ensure that the specified ranges of
IP address are in the same subnet
as the default router and subnet
mask. The configured IP range is
divided into blocks based on the
configured client count.
For Distributed,L3 mode, you can
configure any discontiguous IP
ranges. The configured IP range is
divided into multiple IP subnets that
are sufficient to accommodate the
configured client count.
lease-time <lease_
time>
Defines a lease time for the client in
minutes.
—
720
option <option_
type> <option_
value>
Defines the type and a value for the
DHCP option to use.
—
—
option82 alu
Enables the DHCP Option 82 for the
Centralized,l2 DHCP scope to allow
clients to send DHCP packets with the
Option 82 string.
—
—
reserve {first
<count>| last
<count>}
Reserves the first few and last few IP
addresses in the subnet.
—
—
server-type
Defines any of the following DHCP
distributed,l2,
local
You can configure up to eight DHCP
options supported by the DHCP server
and enter the option value in "" not
exceeding 255 characters.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
ip dhcp | 139
Parameter
Description
Range
<server_type>
assignment modes:
distributed,l3,local,
local,l3,centralized,l2,
centralized,l3
l
l
l
l
l
l
Distributed, L2
Distributed, L3
Local
Local, L3
Centralized, L2
Centralized, L3
Default
server-vlan <idx>
Configures a VLAN ID for the DHCP
scope. To use this subnet, ensure that
the VLAN ID specified here is assigned
to an SSID profile.
1-4093
—
subnet <subnet>
Defines the network IP address
—
—
subnet-mask
<subnet_mask>
Defines the subnet mask for Local,
Local,L3, and distributed,l3 DHCP
scopes. The subnet mask and the
network determine the size of subnet.
—
—
vlan-id <VLAN_
IP> mask <VLAN
mask>
Defines the IP address and subnet
mask for vlan of the DHCP server.
—
—
no…
Removes any existing configuration.
—
—
Usage Guidelines
Use this command to configure the DHCP address assignment for the branches connected to the corporate network
through VPN. You can configure the following types of DHCP profiles.
l
Distributed, L2 — In this mode, the Virtual Controller acts as the DHCP server, but the default gateway is in the
data center. Based on the number of clients specified for each branch, the range of IP addresses is divided.
Based on the IP address range and client count configuration, the DHCP server in the Virtual Controller controls a
scope that is a subset of the complete IP Address range for the subnet distributed across all the branches. This
DHCP Assignment mode is used with the L2 forwarding mode.
l
Distributed, L3 — In this mode, the Virtual Controller acts as the DHCP server and the default gateway. Based
on the number of clients specified for each branch, the range of IP addresses is divided. Based on the IP address
range and client count configuration, the DHCP server in the Virtual Controller is configured with a unique subnet
and a corresponding scope.
l
Local — In this mode, the Virtual Controller acts as both the DHCP Server and the default gateway. The
configured subnet and the corresponding DHCP scope are independent of subnets configured in other W-IAP
clusters. The Virtual Controller assigns an IP address from a local subnet and forwards traffic to both corporate
and non-corporate destinations. The network address is translated appropriately and the packet is forwarded
through the IPSec tunnel or through the uplink. This DHCP assignment mode is used for the NAT forwarding
mode.
l
Local, L3— In this mode, the Virtual Controller acts as a DHCP server and the gateway, and assigns an IP
address from the local subnet. The W-IAP routes the packets sent by clients on its uplink. This mode does not
provide corporate access through the IPsec tunnel. This DHCP assignment mode is used with the L3 forwarding
mode.
l
Centralized, L2—When a Centralized, L2 DHCP scope is configured, the Virtual Controller bridges the DHCP
traffic to the controller over the VPN/GRE tunnel. The IP address is obtained from the DHCP server behind the
140 | ip dhcp
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
controller serving the VLAN/GRE of the client. This DHCP assignment mode also allows you to add the DHCP
option 82 to the DHCP traffic forwarded to the controller.
l
Centralized, L3—For Centralized, L3 clients, the Virtual Controller acts as a DHCP relay agent that forwards the
DHCP traffic to the DHCP server located either in the corporate or local network. The centralized L3 VLAN IP is
used as the source IP. The IP address is obtained from the DHCP server.
Example
The following example configures a distributed,l2 DHCP scope:
(Instant AP)(config)# ip dhcp corpNetwork1
(Instant AP)(DHCP Profile"corpNetwork1")# ip dhcp server-type distributed,l2
(Instant AP)(DHCP Profile"corpNetwork1")# server-vlan 1
(Instant AP)(DHCP Profile"corpNetwork1")# subnet 192.0.1.0
(Instant AP)(DHCP Profile"corpNetwork1")# subnet-mask 255.255.255.0
(Instant AP)(DHCP Profile"corpNetwork1")# default-router 192.0.1.1
(Instant AP)(DHCP Profile"corpNetwork1")# client-count 0
(Instant AP)(DHCP Profile"corpNetwork1")# dns-server 192.0.1.2
(Instant AP)(DHCP Profile"corpNetwork1")# domain-name www.example.com
(Instant AP)(DHCP Profile"corpNetwork1")# lease-time 1200
(Instant AP)(DHCP Profile"corpNetwork1")# ip-range 192.0.1.0 192.0.1.17
(Instant AP)(DHCP Profile"corpNetwork1")# reserve first 2
(Instant AP)(DHCP Profile"corpNetwork1")# option 176
"MCIPADD=10.72.80.34,MCPORT=1719,TFTPSRVR=10.80.0.5,L2Q=1,L2QVLAN=2,L2QAUD=5,L2QSIG=3"
(Instant AP)(DHCP Profile"corpNetwork1")# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant
6.4.0.2-4.1
This command is modified.
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and IP DHCP profile configuration sub-mode.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
ip dhcp | 141
ip dhcp pool
ip dhcp pool
dns-server <IP-address>
domain-name <domain-name>
lease-time <minutes>
subnet <IP-address-subnet>
subnet-mask <Subnet_Mask>
no…
Description
This command configures a DHCP pool on the Virtual Controller.
Syntax
Parameter
Description
Range
Default
dns-server
<address>
Defines the IP address of the DNS server. You can
specify up to eight IP addresses as a comma
separated list.
—
—
domain-name
<domain-name>
Defines the name of domain to which the client
belongs.
—
—
lease-time
<minutes>
Configures the duration of the DHCP lease in
minutes.
—
720
subnet <IPaddress-subnet>
Defines IP address of the subnet.
—
—
subnet-mask
<Subnet_Mask>
Defines the subnet mask of the IP address,
—
—
no…
Removes any existing configuration
—
—
Usage Guidelines
Use this command to configure a DHCP pool. The DHCP server is a built-in server, used for networks in which
clients are assigned IP address by the Virtual Controller. You can customize the DHCP pool subnet and address
range to provide simultaneous access to more number of clients. The pool can support up to 2048 addresses. The
default size of the IP address pool is 512. When a W-IAP receives a DHCP request from a client, it examines the
origin of the request to determine if it a response must be sent. If the IP address of the VLAN matches a configured
DHCP pool, the W-IAP answers the request.
Example
The following command configures a DHCP pool:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
142 | ip dhcp pool
AP)(config)# ip dhcp pool
AP)(DHCP)# domain-name example.com
AP)(DHCP)# dns-server 192.0.2.1
AP)(DHCP)# lease-time 20
AP)(DHCP)# subnet 192.0.2.0
AP)(DHCP)# subnet-mask 255.255.255.0
AP)(DHCP)# end
AP)# commit apply
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and IP DHCP configuration sub-mode.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
ip dhcp pool | 143
l2tpv3 session
l2tpv3 session <l2tpv3_session_profile>
cookie len <len_of_cookie> value <cookie_val>
default-l2-specific-sublayer
l2tpv3 tunnel <l2tpv3_tunnel_prof_to_associate>
tunnel-ip <local_ip_addr_tunnel> mask <tunnel_mask> vlan <tunnel_mgmt_vlan>
no…
Description
This command configures an Layer-2 Tunnel Protocol (L2TP) session profile.
Syntax
Parameter
Description
Range
Default
l2tpv3 session
<name>
Configures the session profile
name.
—
—
cookie len <len_
of_cookie> value
<cookie_val>
Configures the length and
alphanumeric value for the
cookie.
Length: 4/8
Not set.
If cookie length is 4, the
cookie value should
have exactly 8
hexadecimal
characters.
If cookie length is 8, the
cookie value should
have exactly 16
hexadecimal
characters
default-l2specificsublayer
Enables the default l2 specific
sublayer in the L2TPV3 session.
l2tpv3 tunnel
<l2tpv3_tunnel_
prof_to_
associate>
Selects the tunnel profile name
where the session will be
associated.
—
—
tunnel <local_
ip_addr_tunnel>
mask <tunnel_
mask> vlan
<tunnel_mgmt_
vlan>
Configures the local IP address,
network mask, and VLAN ID of
the tunnel.
2-4094
—
no…
Removes the configuration.
—
—
Usage Guidelines
Use this command to configure the session to carry the L2TP data.
Example
The following example configures the L2TPv3 session:
(Instant AP)(config) # l2tpv3 session test_session
(Instant AP)(L2TPv3 Session Profile "test_session")# cookie len 4 value 12345678
144 | l2tpv3 session
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
(Instant
(Instant
2
(Instant
(Instant
AP)(L2TPv3 Session Profile "test_session")# l2tpv3 tunnel test_tunnel
AP)(L2TPv3 Session Profile "test_session")# tunnel-ip 1.1.1.1 mask 255.255.255.0 vlan
AP)(L2TPv3 Session Profile "test_session")# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.4.0.24.1
This command was modified.
Dell Networking W-Series Instant 6.2.1.03.4
This command is introduced.
Command Information
W-IAP Platform
Command Mode
W-IAP108
Configuration mode and L2TPV3 session profile configuration
sub-mode.
W-IAP109
W-IAP135
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
l2tpv3 session | 145
l2tpv3 tunnel
l2tpv3 tunnel <l2tpv3_tunnel_profile>
backup peer-address <peer_IP_address_backup_tunnel>
checksum
failover-mode <mode>
failover-retry-count <retry_count>
failover-retry-interval <interval_in_sec>
hello-timeout <interval_in_sec>
local-port <local_udp_port>
message-digest-type <digest_algo>
mtu <tunnel_MTU>
peer-port <peer_udp_port>
primary peer-address <peer_IP_address_primary_tunnel>
secret-key <key>
no...
Description
This command configures an L2TP tunnel profile.
Syntax
Parameter
Description
Range
Default
l2tpv3 tunnel
<profile-name>
Configures the tunnel
profile name and allows
you to enter the L2TP
tunnel sub-configuration
mode.
—
—
backup peer-address
<peer_IP_address_
backup_tunnel>
Assigns IP address of the
remote end backup tunnel.
—
—
checksum
Enables the generation of
UDP checksums in packets
sent to L2TP peer
IP address.
—
—
failover-mode <mode>
Assigns the backup/primary
tunnel failover mode.
preemptive, nonpreemptive
preemptive
failover-retry-count
<count>
Assigns the number of
failover attempts.
0-5
0
failover-retryinterval <interval_
in_sec>
Assigns the interval
between each failover
attempt.
60-300 seconds
60
hello-timeout
<interval_in_sec>
Configures the interval (in
seconds) at which hello
packets are routed in the
tunnel.
5-300
60
local-port <local_
udp_port>
Assigns the local UDP port
number of the client.
1—65535
1701
146 | l2tpv3 tunnel
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Parameter
Description
Range
Default
message-digest-type
<digest_algo>
Configures the message
digest to be used to create
the MD AVP.
MD5, SHA1, none
MD5
mtu <MTU-size>
Configures a Maximum
Transmission Unit (MTU)
value for the tunnel.
1—65535
1460
peer-port <peer_udp_
port>
Assigns a UDP server port
to the remote end.
1—65535
1701
primary peer-address
<peer_IP_address_
primary_tunnel>
Assigns IP address of the
remote end tunnel.
—
—
secret-key <key>
Configures a shared key to
use for message digest.
—
—
Usage Guidelines
Use this command tunnel data or traffic to L2TP Network Server (LNS).
Example
The following example configures the L2TPv3 tunnel:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# l2tpv3 tunnel test_tunnel
AP)(L2TPv3 Tunnel Profile "test_tunnel")#
AP)(L2TPv3 Tunnel Profile "test_tunnel")#
AP)(L2TPv3 Tunnel Profile "test_tunnel")#
AP)(L2TPv3 Tunnel Profile "test_tunnel")#
AP)(L2TPv3 Tunnel Profile "test_tunnel")#
AP)(L2TPv3 Tunnel Profile "test_tunnel")#
AP)(L2TPv3 Tunnel Profile "test_tunnel")#
AP)(L2TPv3 Tunnel Profile "test_tunnel")#
AP)(L2TPv3 Tunnel Profile "test_tunnel")#
AP)(L2TPv3 Tunnel Profile "test_tunnel")#
AP) # commit apply
primary peer-address 10.0.0.65
backup peer-address 10.0.0.63
failover-mode non-preemptive
failover-retry-count 5
failover-retry-interval 80
hello-timeout 150
mtu 1570
peer-port 3000
secret-key test123
end
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.4
This command is introduced.
Command Information
W-IAP Platform
Command Mode
W-IAP108
Configuration mode and L2TPV3 tunnel configuration sub-mode.
W-IAP109
W-IAP135
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
l2tpv3 tunnel | 147
l3-mobility
l3-mobility
home-agent-load-balancing
virtual-controller <IP-address>
subnet <IP-address-subnet> <subnet-mask> <vlan> <virtual-controller-IP-address>
no...
Description
This command configures Layer-3 mobility on a W-IAP.
Syntax
Parameter
Description
Range
Default
l3-mobility
Enables Layer-3 mobility configuration submode.
—
—
home-agent-loadbalancing
Enables home agent load balancing.
When enabled, the Virtual Controller assigns
the home AP for roamed clients by using a
round robin policy. With this policy, the load
for the APs acting as Home Agents for
roamed clients is uniformly distributed across
the W-IAP cluster.
—
Disabled
virtual-controller
<IP-address>
Adds the IP address of a Virtual Controller to
the mobility domain.
—
—
In the typical deployment scenario, all the APs
are configured in one subnet and all the
clients in another subnet.
You can also deploy APs across different
subnets, in which case the APs in each
subnet will form a cluster with its own Virtual
Controller IP address. To allow clients to roam
seamlessly among all the APs, the Virtual
Controller IP for each of the foreign subnets
must be configured for each W-IAP cluster.
<IP-address>
Configures the IP address for the subnets
support in a W-IAP cluster.
—
—
subnet <subnet-mask>
Specifies the subnet mask.
—
—
<vlan>
Assigns the VLAN applicable to the W-IAP
cluster.
1-4093
—
<virtual-controller
IP>
Specifies the IP address of the Virtual
Controller in a W-IAP cluster.
—
—
no…
Removes the configuration.
—
—
Usage Guidelines
Use this command to configure layer-3 mobility domains on a W-IAP.
Example
The following example configures L3-mobility:
148 | l3-mobility
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# l3-mobility
AP)(L3-mobility)# home-agent-load-balancing
AP)(L3-mobility)# virtual-controller 192.0.2.1
AP)(L3-mobility)# subnet 192.0.2.2 255.255.255.0 1 192.0.2.1
AP)(L3-mobility)# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and L3 mobility configuration sub-mode.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
l3-mobility | 149
led-off
led-off
no…
Description
This command disables LED display on a W-IAP.
Syntax
Command/Parameter
Description
led-off
Disables LED display.
no…
Re-enables LED display.
Usage Guidelines
Use this command to disable the LED display.
Example
The following example disables LED display on a W-IAP:
(Instant AP)(config)# led-off
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
150 | led-off
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
logout
logout
Description
This command logs you out of the current CLI session.
Usage Guidelines
Use this command to log out of the current CLI session and return to the user login prompt.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
logout | 151
mas-integration
mas-integration
no…
Description
This command enables Mobility Access Switch integration on a W-IAP.
Syntax
Parameter
Description
mas-integration
Enables you to integrate the W-IAP with a Mobility Access Switch.
no…
Removes the configuration.
Usage Guidelines
Use this command to integrate Mobility Access Switch with a W-IAP.
You can integrate a W-IAP with a Mobility Access Switch by connecting it directly to the switch port. The following
Mobility Access Switch integration features can be applied while integrating with a W-IAP:
l
Rogue AP containment—When a rogue AP is detected by a W-IAP, it sends the MAC Address of the rogue AP
to the Mobility Access Switch. The Mobility Access Switch blacklists the MAC address of the rogue AP and
turns off the PoE on the port.
l
PoE prioritization— When a W-IAP is connected directly into the Mobility Access Switch port, the Mobility
Access Switch port increases the PoE priority of the port. This is done only if the PoE priority is set by default in
the Mobility Access Switch.
The PoE Prioritization and Rogue AP Containment features is available for ArubaOS 7.2 release on Dell Mobility
Access Switches.
l
GVRP Integration—Configuring GARP VLAN Registration Protocol (GVRP) enables the switch to dynamically
register or de-register VLAN information received from a GVRP applicant such as a W-IAP. GVRP also enables
the switch to propagate the registered VLAN information to the neighboring switches in the network.
The associated static VLANs in the wired and wireless profiles are propagated to the upstream Mobility Access
Switch using GVRP messages.
When a W-IAP is integrated with a Mobility Access Switch, the Link Layer Discovery Protocol (LLDP) is enabled.
Using this protocol, the W-IAPs instruct the Mobility Access Switch to turn off the ports where rogue APs are
connected, perform actions such as increasing the PoE priority, and configure the VLANs on the ports to which the
W-IAPs are connected.
Example
The following example enables Mobility Access Switch integration for a W-IAP:
(Instant AP)(config)# mas-integration
(Instant AP)(config# end
(Instant AP)# commit apply
152 | mas-integration
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
mas-integration | 153
mesh
mesh
no…
Description
This command sets up mesh network on a W-IAP.
Syntax
Parameter
Description
mesh
Enables mesh network on the W-IAP.
no…
Removes the configuration.
Usage Guidelines
Use this command to set up mesh network on a W-IAP. Mesh network requires at least one valid uplink (wired or 3G)
connection. Any provisioned W-IAP that has a valid uplink (wired or 3G) functions as a mesh portal, and the W-IAP
without an Ethernet link functions as a mesh point. The mesh portal can also act as a Virtual Controller. A Mesh
portal (MPP) uses its uplink connection to reach the Virtual Controller, a mesh point, or establishes an all wireless
path to the mesh portal. Mesh portals and mesh points are also known as mesh nodes, a generic term used to
describe W-IAPs configured for mesh.
Mesh W-IAPs detect the environment when they boot up, locate and associate with their nearest neighbor, to
determine the best path to the mesh portal.
Instant mesh functionality is supported only on dual radio W-IAPs only. On dual-radio W-IAPs, the 5 GHz radio is
always used for both mesh-backhaul and client traffic, while the 2.4 GHz radio is always used for client traffic.
Mesh service is automatically enabled on 802.11a band for dual-radio W-IAP only, and this is not configurable.
The mesh network must be provisioned for the first time by plugging into the wired network. After that, mesh works
on W-IAP ROWs like any other regulatory domain.
Example
The following example enables mesh network on a W-IAP:
(Instant AP)(config)# mesh
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
154 | mesh
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
mesh | 155
mgmt-accounting
mgmt-accounting command all
no…
Description
This command is used to enable accounting privileges on TACACS+ servers for management users.
Syntax
Parameter
Description
mgmt-accounting command all
Configures TACACS+ servers to enable accounting for
management users.
no…
Removes the configuration.
Usage Guidelines
Use this command to record the user name of the management users and the respective IP address sending the
request to account for the usage of the authorized network services.
Example
The following example configures a TACACS+ server for management accounting
(Instant Access Point)(config)# mgmt-accounting command all tacacs1
(Instant Access Point)(config)# end
(Instant Access Point)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.4.0.24.1
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
156 | mgmt-accounting
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
mgmt-auth-server
mgmt-auth-server <server>
no…
Description
This command configures authentication servers for management user interface of the Virtual Controller.
Syntax
Parameter
Description
mgmt-auth-server <server>
Configures a server for management user authentication.
no…
Removes the configuration.
Usage Guidelines
Use this command to configure a management authentication server for administrator users of a Virtual Controller.
Example
The following example configures an authentication server for the management user interface:
(Instant AP)(config)# mgmt-auth-server server1
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
mgmt-auth-server | 157
mgmt-auth-server-load-balancing
mgmt-auth-server-load-balancing
no…
Description
This command enables load balancing when two authentication servers are configured for management user
authentication.
Syntax
Parameter
Description
mgmt-auth-server-load-balancing
Enables load balancing between the primary and the backup
authentication servers
no…
Removes the configuration.
Usage Guidelines
Use this command to enable load-balancing when two servers are configured.
Example
The following example enables load-balancing between two authentication servers.
(Instant AP)(config)# mgmt-auth-server-load-balancing
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
158 | mgmt-auth-server-load-balancing
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
mgmt-auth-server-local-backup
mgmt-auth-server-local-backup
no…
Description
Configures a secondary internal authentication server that will validate the management interface user credentials at
runtime.
Syntax
Parameter
Description
mgmt-auth-server-local-backup
Configures a backup internal server for management user
authentication.
When enabled, the authentication switches to Internal if there is no
response from the RADIUS server (RADIUS server timeout).
no…
Removes the configuration.
Usage Guidelines
Use this command to configure a backup authentication server for the Virtual Controller management interface.
Example
The following example configures a backup internal authentication server:
(Instant AP)(config)# mgmt-auth-server-local-backup
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
mgmt-auth-server-local-backup | 159
mgmt-user
mgmt-user <username> [<password>][<type>]
Description
This command configures user credentials for access to the Virtual Controller Management User Interface.
Syntax
Parameter
Description
mgmt-user
Configures administrator credentials.
<username>
Creates a User name for the administrator user.
<password>
Creates a password for the administrator user.
<type>
Indicates the type of the user. For example, users with read-only privilege
or the guest management user.
Usage Guidelines
Use this command to configure administrator credentials to access and configure the W-IAP.
Example
The following example configures administrator login credentials for the W-IAP management interface:
(Instant AP)(config)# mgmt-user User1 Password123 guest-mgmt
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.14.0
This command is modified.
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
160 | mgmt-user
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
name
name <name>
Description
This command configures a unique name for the W-IAP.
Syntax
Parameter
Description
name <name>
Configures a name for the W-IAP or the Virtual Controller.
Usage Guidelines
Use this command to configure a name for the W-IAP:
Example
The following example configures a name for the W-IAP:
(Instant AP)# hostname <system-name>
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
name | 161
ntp-server
ntp-server <Name>
no…
Description
This command configures NTP server for a W-IAP.
Syntax
Parameter
Description
Default
ntp-server <Name>
Configures the IP address or the URL (domain name) of
the NTP server.
pool.ntp.org
no
Removes the configuration
—
Usage Guidelines
The Network Time Protocol (NTP) helps obtain the precise time from a server and regulate the local time in each
network element. If NTP server is not configured in the Instant network, a W-IAP reboot may lead to variation in time
data.
Example
The following command configures an NTP server for a W-IAP:
(Instant AP)(config)# ntp-server <name>
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
162 | ntp-server
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
opendns
opendns <user> <password>
no...
Description
This command configures OpenDNS credentials for filtering content and to create Internet access policies that allow
or deny user access to websites based on website categories and security ratings.
Syntax
Parameter
Description
opendns
Configures user credentials to enable access to OpenDNS to provide
enterprise-level content filtering.
<user>
Configures user name to access OpenDNS.
<password>
Configures password to access OpenDNS.
no…
Removes the configuration.
Usage Guidelines
Use this command to configure OpenDNS credentials to allow Instant to filter content at the enterprise-level.
Example
The following example configures OpenDNS credentials:
(Instant AP)(config)# opendns <username <password>
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
opendns | 163
organization
organization <name>
no…
Description
This command configures an organization string for W-IAPs managed or monitored by the W-AirWave Management
console.
Syntax
Parameter
Description
Range
organization <name>
Specifies the name of your organization.
You can use any of the following
strings:
l AMP Role— "Org Admin" (initially
disabled)
l AMP User— "Org Admin"
(assigned to the role "Org
Admin")
l Folder— "Org" (under the Top
folder in AMP)
l Configuration Group— "Org"
You can also assign additional
strings to create a hierarchy of sub
folders under the folder named
"Org": For example:
l subfolder1 for a folder under the
"Org" folder
l subfolder2 for a folder under
subfolder1
no…
Removes the configuration settings.
—
Usage Guidelines
Use this command to specify an organization string for integrating the W-AirWave Management Server with the WIAP. The organization is a set of colon-separated strings created by the W-AirWave administrator to accurately
represent the deployment of each W-IAP. This string is defined by the installation personnel on the site.
Example
The following command configures a W-AirWave organization string:
(Instant AP)(config)# organization dell
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
164 | organization
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
organization | 165
ping
ping <host>
Description
This command sends ICMP echo packets to the specified IP address.
Syntax
Parameter
Description
<host>
Displays the IP address of the host.
Usage Guidelines
You can send up to five ICMP echo packets to a specified IP address. The W-IAP times out after two seconds.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Command Information
166 | ping
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
pppoe-uplink-profile
pppoe-uplink-profile <profile>
pppoe-username <username>
pppoe-passwd <password>
pppoe-svcname <svcname>
pppoe-chapsecret <password>
pppoe-unnumbered-local-l3-dhcp-profile <dhcp-profile>
no…
Description
Use this command to configure PPPoE uplink profile.
Syntax
Parameter
Description
pppoe-uplink-profile <profile>
Creates an uplink profile and enables the PPPoE uplink profile
configuration mode.
pppoe-username <username>
Configures a user name to allow a user to log into the DSL network.
pppoe-passwd <password>
Configures a password for the user to log into the DSL network.
pppoe-svcname <svcname>
Specifies the PPPoE service provided by your service provider.
pppoe-chapsecret <password>
Configures a secret key used for Challenge Handshake
Authentication Protocol (CHAP) authentication.
You can use a maximum of 34 characters for the CHAP secret key.
pppoe-unnumbered-local-l3dhcp-profile <dhcp-profile>
Configures the Local,L3 DHCP gateway IP address as the local IP
address of the PPPoE interface. When configured, the local interface
acts as an unnumbered PPPoE interface and allows the entire
Local,L3 DHCP subnet to be allocated to clients.
no…
Removes the configuration.
Usage Guidelines
Use this command to configure PPPoE uplink connection for a W-IAP.
Example
The following example configures the PPPoE uplink on a W-IAP:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config) # pppoe-uplink-profile
AP)(pppoe-uplink-profile)# pppoe-username User1
AP)(pppoe-uplink-profile)# pppoe-passwd Password123
AP)(pppoe-uplink-profile)# pppoe-svcname internet03
AP)(pppoe-uplink-profile)# pppoe-chapsecret 8e87644deda9364100719e017f88ebce
AP)(pppoe-uplink-profile)# pppoe-unnumbered-local-l3-dhcp-profile dhcpProfile1
AP)(pppoe-uplink-profile)# end
AP)# commit apply
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
pppoe-uplink-profile | 167
Command History
Version
Description
Dell Networking W-Series Instant 6.4.0.24.1
This command is modified.
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and PPPoE uplink profile configuration submode.
168 | pppoe-uplink-profile
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
proxy
proxy {exception <host>| server <host> <port>}
Description
This command configures HTTP proxy settings.
Syntax
Parameter
Description
exception
<hostname>
Sets the IP address or the domain name of the host to be
added under the exception list.
server
<hostname>
<port number>
Sets the HTTP proxy server's IP address or domain name and
the port number.
Usage Guidelines
This command configures the HTTP proxy settings in a W-IAP to download the image from the cloud server.
Example
The following example configures an HTTP proxy settings in a W-IAP:
(Instant
(Instant
(Instant
(Instant
AP)(config)# proxy exception 192.0.2.2
AP)(config)# proxy server 192.0.2.1 8080
AP)(config)# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.14.0
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
proxy | 169
reload
reload <all>
Description
This command performs a reboot of the Virtual Controller.
Syntax
Parameter
Description
<all>
Reloads all W-IAPs in a cluster.
Usage Guidelines
Use this command to reboot a W-IAP after making configuration changes or under the guidance of Dell Networks
customer support. The reload command powers down the W-IAP, making it unavailable for configuration. After the
W-IAP reboots, you can access it via a local console connected to the serial port, or through an SSH, Telnet, or UI
session. If you need to troubleshoot the W-IAP during a reboot, use a local console connection.
After you use the reload command, the W-IAP prompts you to confirm this action. If you have not saved your
configuration, the W-IAP returns the following message:
Do you want to save the configuration (y/n):
l
Enter y to save the configuration.
l
Enter n to not save the configuration.
l
Press [Enter] to exit the command without saving changes or rebooting the W-IAP.
If your configuration has already been saved, the W-IAP returns the following message:
Do you really want to reset the system(y/n):
l
Enter y to reboot the W-IAP.
l
Enter n to cancel this action.
The command will timeout if you do not enter y or n.
Example
The following command assumes you have already saved your configuration and you must reboot the W-IAP:
The W-IAP returns the following messages:
Do you really want to reset the system(y/n): y
System will now restart!
...
Restarting system.
Command History
170 | reload
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
reload | 171
remove-blacklist-client
remove-blacklist-client <MAC_address> <AP_name>
Description
This command allows you to delete the clients that are blacklisted.
Syntax
Parameter
Description
MAC-address
Adds the MAC address of the blacklisted client.
AP_name
Adds the access point name to which the client is connected to.
no…
Removes the specified configuration parameter.
Usage Guidelines
Use this command to remove the entries for the clients that are dynamically blacklisted.
Example
The following command deletes the blacklisted W-IAP client entries:
(Instant AP)(config)# remove-blacklist-client d7:a:b2:c3:45:67 AP125
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
172 | remove-blacklist-client
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
restrict-corp-access
restrict-corp-access
no…
Description
This command configures restricted access to the corporate network.
Syntax
Parameter
Description
no…
Removes the configuration.
Usage Guidelines
Use this command to configure restricted corporate to block unauthorized users from accessing the corporate
network. When restricted corporate access is enabled, corporate access is blocked from the uplink port of master
W-IAP, including clients connected to a slave W-IAP.
Example
The following example enables restricted access to the corporate network;
(Instant AP)(config) # restrict-corp-access
(Instant AP)(config) # end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.14.0
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
restrict-corp-access | 173
restricted-mgmt-access
restricted-mgmt-access <subnet> <mask>
no…
Description
This command configures management subnet on a W-IAP.
Syntax
Parameter
Description
subnet
Configures a management subnet address.
mask
Configures the subnet mask for the management subnet address.
no…
Removes the configuration.
Usage Guidelines
Use this command to configure management subnets. This ensures that the W-IAP management is carried out only
from these subnets. When the management subnets are configured, Telnet, SSH, and UI access is restricted to
these subnets only.
Example
The following example configures a management subnet;
(Instant AP)(config) # restricted-mgmt-access 192.0.2.13 255.255.255.255
(Instant AP)(config) # end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.14.0
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
174 | restricted-mgmt-access
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
rf dot11a-radio-profile
rf dot11a-radio-profile
beacon-interval <interval>
csa-count <count>
dot11h
interference-immunity <immunity-level>
legacy-mode
max-distance <count>
spectrum-band <type>
spectrum-monitor
no…
Description
This command configures a 5.GHz or 802.11a radio profile for a W-IAP.
Syntax
Parameter
Description
Range
Default
rf dot11a-radioprofile
Enables the 5.0 GHz RF configuration submode
—
—
beacon-interval
<interval>
Enter the Beacon period for the W-IAP in
milliseconds.
60-500
100
0-10
2
When enabled, the 802.11 beacon
management frames are transmitted by the
access point at the specified interval.
csa-count <count>
Configures the number of channel switching
announcements that must be sent before
switching to a new channel.
This allows associated clients to recover
gracefully from a channel change.
dot11h
Allows the W-IAP to advertise its 802.11d
(country information) and 802.11h (transmit
power control) capabilities.
—
Disabled
interference-immunity
<immunity-level>
Configures the immunity level to improve
performance in high-interference
environments. You can specify any of the
following immunity levels:
0-5
2
l
l
l
l
Level 0— no ANI adaptation.
Level 1— Noise immunity only. This level
enables power-based packet detection by
controlling the amount of power increase
that makes a radio aware that it has
received a packet.
Level 2— Noise and spur immunity. This
level also controls the detection of OFDM
packets, and is the default setting for the
Noise Immunity feature.
Level 3— Level 2 settings and weak OFDM
immunity. This level minimizes false detects
on the radio due to interference, but may
also reduce radio sensitivity. This level is
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
rf dot11a-radio-profile | 175
Parameter
Description
Range
Default
recommended for environments with a
high-level of interference related to 2.4 GHz
appliances such as cordless phones.
l Level 4— Level 3 settings, and FIR
immunity. At this level, the AP adjusts its
sensitivity to in-band power, which can
improve performance in environments with
high and constant levels of noise
interference.
l Level 5— The AP completely disables PHY
error reporting, improving performance by
eliminating the time the W-IAP would spend
on PHY processing.
NOTE: Increasing the immunity level makes
the AP to lose a small amount of range.
legacy-mode
Enables the W-IAPs to run the radio in non802.11n mode.
—
Disabled
max-distance <count>
Configures the maximum distance between a
client and an AP or between a mesh point and
a mesh portal in meters. This value is used to
derive ACK and CTS timeout times.
600-1000
0
A value of 0 specifies the default settings for
this parameter, where timeouts are only
modified for outdoor mesh radios which use a
distance of 16km.
spectrum-band <type>
Allows you to specify the portion of the channel
to monitor for 5 GHz configuration.
—
—
spectrum-monitor
Allows the W-IAPs in access mode to continue
with normal access service to clients, while
performing additional function of monitoring RF
interference (from both neighboring APs and
non Wi-Fi sources such as, microwaves and
cordless phones) on the channel they are
currently serving clients.
—
—
no…
Removes the configuration.
—
—
Usage Guidelines
Use this command to create a 5.0 GHz radio profile on a W-IAP.
Example
The following example configures the 5 GHz radio profile:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# rf dot11a-radio-profile
AP)(RF dot11a Radio Profile)# beacon-interval 100
AP)(RF dot11a Radio Profile)# legacy-mode
AP)(RF dot11a Radio Profile)# dot11h
AP)(RF dot11a Radio Profile)# interference-immunity 3
AP)(RF dot11a Radio Profile)# max-distance 600
AP)(RF dot11a Radio Profile)# csa-count 2
AP)(RF dot11a Radio Profile)# spectrum-monitor
AP)(RF dot11a Radio Profile)# end
176 | rf dot11a-radio-profile
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.1-4.0
This command is modified.
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and RF dot11a Radio Profile configuration
sub-mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
rf dot11a-radio-profile | 177
rf dot11g-radio-profile
rf dot11g-radio-profile
beacon-interval <interval>
csa-count <count>
dot11h
interference-immunity <immunity-level>
legacy-mode
max-distance <count>
spectrum-monitor
no…
Description
This command configures a 2.4.GHz or 802.11g radio profile for a W-IAP.
Syntax
Parameter
Description
Range
Default
rf dot11g-radioprofile
Enables the 2.4 GHz RF configuration submode
—
—
beacon-interval
<interval>
Enter the Beacon period for the W-IAP in
milliseconds.
60-500
100
0-10
2
When enabled, the 802.11 beacon
management frames are transmitted by the
access point at the specified interval.
csa-count <count>
Configures the number of channel switching
announcements that must be sent before
switching to a new channel.
This allows associated clients to recover
gracefully from a channel change.
dot11h
Allows the W-IAP to advertise its 802.11d
(country information) and 802.11h (transmit
power control) capabilities.
—
Disabled
interference-immunity
<immunity-level>
Configures the immunity level to improve
performance in high-interference
environments. You can specify any of the
following immunity levels:
0-5
2
l
l
l
178 | rf dot11g-radio-profile
Level 0— no ANI adaptation.
Level 1— Noise immunity only. This level
enables power-based packet detection by
controlling the amount of power increase
that makes a radio aware that it has
received a packet.
Level 2— Noise and spur immunity. This
level also controls the detection of OFDM
packets, and is the default setting for the
Noise Immunity feature. l Level 3— Level 2
settings and weak OFDM immunity. This
level minimizes false detects on the radio
due to interference, but may also reduce
radio sensitivity. This level is recommended
for environments with a high-level of
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Parameter
Description
Range
Default
interference related to 2.4 GHz appliances
such as cordless phones.
l Level 4— Level 3 settings, and FIR
immunity. At this level, the AP adjusts its
sensitivity to in-band power, which can
improve performance in environments with
high and constant levels of noise
interference.
l Level 5— The AP completely disables PHY
error reporting, improving performance by
eliminating the time the W-IAP would spend
on PHY processing.
NOTE: Increasing the immunity level makes
the AP to lose a small amount of range.
legacy-mode
Enables the W-IAPs to run the radio in non802.11n mode.
—
Disabled
max-distance <count>
Configures the maximum distance between a
client and an AP or between a mesh point and
a mesh portal in meters. This value is used to
derive ACK and CTS timeout times.
600-1000
0
A value of 0 specifies the default settings for
this parameter, where timeouts are only
modified for outdoor mesh radios which use a
distance of 16km.
spectrum-monitor
Allows the W-IAPs in access mode to continue
with normal access service to clients, while
performing additional function of monitoring RF
interference (from both neighboring APs and
non Wi-Fi sources such as, microwaves and
cordless phones) on the channel they are
currently serving clients.
—
Disabled
no…
Removes the configuration.
—
—
Usage Guidelines
Use this command to create a 2.4 GHz radio profile on a W-IAP.
Example
The following example configures the 2.4GHz radio profile:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# rf dot11g-radio-profile
AP)(RF dot11g Radio Profile)# beacon-interval 200
AP)(RF dot11g Radio Profile)# no legacy-mode
AP)(RF dot11g Radio Profile)# dot11h
AP)(RF dot11g Radio Profile)# interference-immunity 3
AP)(RF dot11g Radio Profile)# max-distance 600
AP)(RF dot11g Radio Profile)# csa-count 2
AP)(RF dot11g Radio Profile)# spectrum-monitor
AP)(RF dot11g Radio Profile)# end
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
rf dot11g-radio-profile | 179
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.1-4.0
This command is modified.
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and RF dot11g Radio Profile sub-mode
180 | rf dot11g-radio-profile
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
rf-band
rf-band {2.4| 5.0| all}
Description
This command configures the radio frequency band for a W-IAP.
Syntax
Parameter
Description
Range
Default
rf-band {2.4| 5.0|
all}
Configures a radio frequency band for a W-IAP.
You can configure any of the following options:
2.4, 5.0, all
all
l
l
l
2.4 — For 2.4 GHz band or 802.11g
configuration
5 — For 5 GHz and 802.11a configuration
all - For a mixed configuration of 2.4.GHz and 5
GHz. If you do not specify any value, by default
both 5 GHz and 2.4 GHz bands are selected.
Usage Guidelines
Use this command to configure RF band for a W-IAP.
Example
The following example configures the 5 GHz RF band for a W-IAP.
(Instant AP)(config)# rf-band 5.0
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
rf-band | 181
rft
rft test profile
antenna-connectivity ip-addr <IP-addr> dest-mac <MAC-addr> phy {a|g}
ht-link-quality ip-addr <IP-addr> dest-mac <MAC-addr> phy {a|g} mcs <mcs>
link-quality ip-addr <IP-addr> dest-mac <MAC-addr> phy {a|g}
raw ip-addr <IP-addr> dest-mac <MAC-addr> phy {a|g}
Description
This command is used for RF troubleshooting.
Syntax
Parameter
Description
rft test profile
Allows you to run RF troubleshooting commands
antenna-connectivity
Allows you to test the antenna connectivity
ht-link-quality
Allows you to test the HT link quality.
link-quality
Allows you to test the quality of the link.
raw
Performs a raw test.
ip-addr <IP-addr>
Indicates the IP address of the W-IAP that performs the test.
dest-mac <MAC-addr>
Specifies MAC address of the client to be tested.
phy
Indicates the 802.11 type, either a or g.
mcs <mcs>
Indicates the type of Modulation Coding Scheme (MCS).
Usage Guidelines
This command can run predefined test profiles for antenna connectivity, link quality, or raw testing. Run these
commands only under the supervision of a Dell support representative.
In this release, this command is not available on W-IAP224/225, and W-IAP274/275 platforms.
Example
The following example shows the RF test command that can be run for testing the antenna connectivity:
(Instant AP)# rft test profile 192.0.2.1 dest-mac 00:1A:1E:00:00:00 phy a
Command History
182 | rft
Version
Description
Dell Networking W-Series Instant
6.4.0.2-4.1
This command is introduced.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command Information
W-IAP Platform
Command Mode
All platforms except W-IAP224/225,
and W-IAP274/275
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
rft | 183
routing-profile
routing-profile
route <destination> <mask> <gateway>
no...
Description
This command configures a routing profile to define the corporate subnets, which must to be tunneled through IPSec.
Syntax
Parameter
Description
routing-profile
<profile>
Creates a routing profile for routing traffic into the VPN tunnel.
route
Configures route parameters.
<destination>
Configures the destination network that is reachable through the VPN tunnel.
<mask>
Specify the subnet mask of network that is reachable through the VPN tunnel.
<gateway>
Specify the gateway to which traffic must be routed. This IP address must be the
controller IP address on which the VPN connection is terminated.
no…
Removes the configuration
Usage Guidelines
Use this command to configure a routing profile for VPN connections.
Example
The following example configures a routing profile:
(Instant
(Instant
(Instant
(Instant
AP)(config)# routing-profile
AP)(Routing-profile)# route 192.0.1.0 255.255.255.0 192.0.2.0
AP)(Routing-profile)# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and routing profile configuration sub-mode.
184 | routing-profile
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show 1xcert
show 1xcert
Description
This command displays the details about the external server certificate, which is used by the W-IAP for client
authentication.
Usage Guidelines
Use this command to view information about the server certificates uploaded to a W-IAP.
Example
The following example shows the output of show 1xcert command:
Default Server Certificate:
Version :3
Serial Number :01:DA:52
Issuer :C=US, O=GeoTrust Inc., OU=Domain Validated SSL, CN=GeoTrust DV SS L CA
Subject :0x05=lLUge2fRPkWcJe7boLSVdsKOFK8wv3MF, C=US, O=securelogin.dell.com, OU=GT28470348,
OU=See www.geotrust.com/resources/cps (c)11, OU=Doma in Control Validated - QuickSSL(R)
Premium, CN=securelogin.dell.com
Issued On :2011-05-11 01:22:10
Expires On :2017-08-11 04:40:59
Signed Using :SHA1
RSA Key size :2048 bits
The output of this command describes details such as the version, serial number, subject, issue date, expiry date,
type of encryption, and RSA key information for the certificates uploaded to the W-IAP.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show 1xcert | 185
show about
show about
Description
This command displays information about Instant.
Usage Guidelines
Use this command to view information such as Instant version, build time and W-IAP model.
Example
The show about command displays the Build Time, W-IAP model number, the Instant version, website address of
organization, and Copyright information. The following example shows the show about command output:
Name :Aruba Operating System Software
Type :W-AP105
Build Time :2013-04-19 08:30:19 PDT
Version :6.2.1.0-3.3.0.0_38115
Website :http://www.dell.com
Legal :Copyright (c) 2002-2013, Aruba Networks, Inc.
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
186 | show about
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show access-rule
show access-rule <name>
Description
This command displays the details of access rules configured for the wired or wireless clients associated with a WIAP.
Syntax
Parameter
Description
<name>
Displays the access rule configuration details based the name specified for this
parameter.
Usage Guidelines
Use this command to view information an access rule configured for a network profile.
Example
The following example shows the output displayed for the show access-rule command:
Access Rule Profiles
-------------------Name
---ethersphere-instant-wpa2
default_wired_port_profile
wired-instant
ethersphere-instant-cp
ethersphere-instant
ether-wired
11-android
On specifying a name of the SSID or the port profile along with the show access-rule <name> command, the list of
access rules configured for the specified profile is displayed. The following example shows the output of this
command:
Access Rules
-----------Dest IP Dest Mask Dest Match Protocol (id:sport:eport) Application Action Log TOS 802.1P
Blacklist App Throttle (Up:Down) Mirror DisScan ClassifyMedia
------- --------- ---------- ------------------------- ----------- ------ --- --- ------ -------- ---------------------- ------ ------- ------------any any match any permit 192.0.2.7 255.255.255.255 match h323-tcp permit
any any match any permit 192.0.2.7 255.255.255.255 match h323-udp permit
any any match dhcp permit
any any match app bebo deny
any any match app babylon deny
any any match app baidu-hi- games deny
any any match app bluejayfilms deny
any any match appcategory gaming deny
any any match webcategory shopping deny
any any match webcategory abused-drugs deny
any any match webcategory dead-sites deny
any any match webreputation high-risk-sites deny
Blacklist App Throttle (Up:Down) Mirror DisScan ClassifyMedia
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show access-rule | 187
---- ---------------------- - ----- ------- ------------Vlan Id :0
ACL Captive Portal:disable
ACL ECP Profile :default
CALEA :disable
Bandwidth Limit :upstream disable
The output of this command displays information about the access rule parameters configured for a specific wired or
wireless profile. It indicates whether a particular type of traffic is allowed to a particular destination, and the service
and protocol in use and if options such as logging and prioritizing traffic are enabled when the rule is triggered. If the
DPI access rules are configured, it displays the list of rules configured to allow or deny access to certain
applications, application categories, web categories, and websites based on their reputation score.
Command History
Version
Description
Dell Networking W-Series Instant
6.4.0.2-4.1
This command is modified
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
188 | show access-rule
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show access-rule-all
show access-rule-all
Description
This command displays the details of the access rules configured for all wired and wireless profiles on the W-IAP.
Usage Guidelines
Use this command to view information access rules configured for all wired and wireless profiles on the W-IAP.
Example
The following example shows the partial output of the show access-rule-all command:
Access Rule Name :default_wired_port_profile
In Use :Yes
Access Rules
-----------Dest IP Dest Mask Dest Match Protocol (id:sport:eport) Application Action Log TOS 802.1P
Blacklist App Throttle (Up:Down) Mirror DisScan ClassifyMedia
------- --------- ---------- ------------------------- ----------- ------ --- --- ------ -------- ---------------------- ------ ------- ------------any any match any permit
masterip 0.0.0.0 match http permit
masterip 0.0.0.0 match 6:4343:4343 permit
any any match dhcp permit
Vlan Id :0
ACL Captive Portal:disable
ACL ECP Profile :default
CALEA :disable
Bandwidth Limit :downstream disable upstream disable
Access Rule Name :NewRole17
In Use :No
Access Rules
-----------Access Rules
-----------Dest IP Dest Mask Dest Match Protocol (id:sport:eport) Application Action Log TOS 802.1P
Blacklist App Throttle (Up:Down) Mirror DisScan ClassifyMedia
------- --------- ---------- ------------------------- ----------- ------ --- --- ------ -------- ---------------------- ------ ------- ---------10.17.88.188 255.255.255.255 match http permit
10.17.88.188 255.255.255.255 match 6:4343:4343 permit
any any match dhcp permit
any any match dns permit
Vlan Id :0
ACL Captive Portal:disable
ACL ECP Profile :default
CALEA :disable
Bandwidth Limit :downstream disable upstream disable
Access Rule Name :NewRole18
In Use :No
The output of this command includes the following parameters:
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show access-rule-all | 189
Parameter
Description
Access Rule Name
Displays the name of the access rule.
In use
Indicates if the access rules are in use.
Access Rules
Displays the access rules parameter for each rule configured for the SSID or
Wired profile users.
VLAN Id
Indicates the VLAN ID associated with the SSID or wired profile access rules
ACL Captive Portal
Indicates if the ACL rules are applicable to the captive portal users.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
190 | show access-rule-all
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show airgroup
show airgroup {blocked-queries [dlna| mdns]| blocked-service-id [dlna| mdns]| cache {<MACaddress> | entries [dlna| mdns]} | cppm {auth server [coa-capable | non-coa-only] | entries |
query-interval | server}| cppm-entry <MAC-address> | debug statistics| internal-state
statistics | servers [dlna| mdns| verbose]| status | swarm-info| users [dlna| mdns| verbose]}
Description
This command displays the AirGroup configuration details for a W-IAP client.
Syntax
Parameter
Description
blocked-queries [dlna
|mdns]
Displays blocked queries if any.
blocked-service-id
[dlna| mdns]
Displays blocked services and service IDs if any.
cache <MAC-address>
cache entries [dlna|
mdns]
Displays AirGroup cache details for a specific W-IAP or for the W-IAP clients in a
cluster.
cppm {auth server
[coa-capable | noncoa-only] | entries |
query-interval |
server}
Displays CPPM server details associated with AirGroup configuration.
cppm-entry <MACaddress>
Displays CPPM server details for an AirGroup client.
debug statistics
Displays debug statistics for AirGroup enabled W-IAPs.
internal-state
statistics
Displays statistical details of queries and responses, and RADIUS client
messages.
servers [dlna| mdns|
verbose]
Displays AirGroup server details.
status
Indicates the AirGroup feature activation status.
swarm-info
Displays information about the AirGroup cluster.
users [dlna| mdns|
verbose]
Displays the list of AirGroup users.
Usage Guidelines
Use the show airgroup commands to view the AirGroup configuration details on a W-IAP.
Example
Example outputs for some of the show airgroup commands are as follows:
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show airgroup | 191
show airgroup blocked-queries
The show airgroup blocked-queries command output displays the blocked queries if any:
AirGroup dropped Query IDs
-------------------------Service ID #query-hits
---------- ----------Num dropped Query IDs:0
show airgroup blocked-service-id
The show airgroup blocked-service-id command output displays the blocked AirGroup service IDs if any:
AirGroup Blocked Service IDs
---------------------------Origin Service ID #response-hits
------ ---------- -------------Num Blocked Service-ID:0
show airgroup cache entries
The following output is displayed for the show airgroup cache entries command:
Cache Entries
------------Name Type Class TTL Origin Expiry Last Update
---- ---- ----- --- ------ ------ ----------_airplay._tcp.local PTR IN 4500 10.16.94.236 3696.00 Tue May 13 19:32:11 2014
_raop._tcp.local PTR IN 4500 10.16.94.236 3794.31 Tue May 13 19:32:11 2014
BLR-DPARASAR-T4._airplay._tcp.local SRV/NBSTAT IN 120 10.16.94.236 311.38 Tue May 13 19:32:11
2014
2577037A8680@BLR-DPARASAR-T4._raop._tcp.local SRV/NBSTAT IN 120 10.16.94.236 134.14 Tue May 13
19:32:11 2014
BLR-DPARASAR-T430S.local A IN 120 10.16.94.236 255.07 Tue May 13 19:32:11 2014
BLR-DPARASAR-T430S.local AAAA IN 120 10.16.94.236 393.69 Tue May 13 19:32:11 2014
BLR-DPARASAR-T4._airplay._tcp.local TXT IN 4500 10.16.94.236 3784.51 Tue May 13 19:32:11 2014
2577037A8680@BLR-DPARASAR-T4._raop._tcp.local TXT IN 4500 10.16.94.236 3840.38 Tue May 13
19:32:11 2014
urn:schemas-upnp-org:device:MediaRenderer:1 N/A N/A 1800 10.16.94.236 N/A Tue May 13 19:33:51
2014
The output of this command includes the following information:
Column
Description
Name
Indicates the name of AirGroup server.
Type
Indicates the AirGroup model.
Class
Indicates the class of the mDNS record.
TTL
Indicates the duration after which the cache entries expire.
Origin
Indicates the origin IP address of the cache entries.
Expiry
Indicates the expiration details.
Last Update
Indicates when the entries were last updated.
show airgroup cppm auth server non-coa-only
The following output is displayed for the show airgroup cppm auth server non-coa-only command:
192 | show airgroup
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
All Airgroup Non-CoA-only Servers known to MDNS
----------------------------------------------Server IP-Address Port timeout rfc3576 rfc3576-only rfc3576-port
------ ---------- ---- ------- ------- ------------ -----------test 192.0.2.0 1812 5 Disabled Disabled 5999
test123 192.0.2.1 1812 5 Disabled Disabled 5999
show airgroup cppm auth server coa-capable
The following output is displayed for the show airgroup cppm auth server coa-capable command:
All Airgroup CoA-capable Servers known to MDNS
---------------------------------------------Server IP-Address Port timeout rfc3576 rfc3576-only rfc3576-port
------ ---------- ---- ------- ------- ------------ -----------server1 192.0.1.1 1812 5 Enabled Enabled 5999
show airgroup cppm server
The following output is displayed for the show airgroup cppm server command:
CPPM Servers
-----------Server IP-Address Port timeout rfc3576 rfc3576-only rfc3576-port
------ ---------- ---- ------- ------- ------------ -----------test 192.0.2.0 1812 5 Disabled Disabled 5999
test123 192.0.2.1 1812 5 Disabled Disabled 5999
The output of these commands provide the following information:
Column
Description
Server
Indicates the name of the CPPM server.
IP address
Indicates the IP address of the CPPM server.
Port
Indicates the authorization port number of the CPPM server.
timeout
Indicates timeout value in seconds for one RADIUS request.
rfc3576
Indicates if the W-IAPs are configured to process RFC 3576-compliant Change of
Authorization (CoA).
rfc3576-only
Indicates if W-IAPs are configured to be RFC 3576 compliant only.
rfc3576-port
Indicates the port number used for sending AirGroup CoA.
show airgroup cppm entries
The following output is displayed for the show airgroup cppm entries command:
swarm id = fc6520ad018ee6eb13bdc6b985e0fe6361bd37f7d25212a77e
-------------------------------------------------------------------ap id = d8:c7:c8:c4:42:98 ap ip = 192.0.2.0 update no = 0
------------------------------------Device device-owner shared location-id AP-name shared location-id AP-FQLN
------ ------------ -------------------------- -------------------------shared location-id AP-group shared user-list shared role-list
------------------ ---------------- ---------------Num CPPM Entries:0
The output of this command provides the following information:
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show airgroup | 193
Column
Description
swarm id
Indicates the cluster ID of the W-IAP.
ap id
Displays the MAC address of the W-IAP on which AirGroup is configured.
ap ip
Displays the IP address of the W-IAP on which AirGroup is configured.
update no
Indicates the number of configuration updates if any.
Device
Indicates the device for which AirGroup is configured.
deviceowner
Indicates the device owner's identity.
shared
location-id
AP-name
Indicates the shared location ID associated with the AP name
shared
location-id
AP-FQLN
Indicates the shared location ID associated with the fully qualified domain name of the AP
shared
location-id
AP-group
Indicates the shared location ID associated with the AP group.
shared
user-list
Indicates the list of shared users.
shared
role-list
Indicates the list of shared user roles.
Num CPPM
Entries
Indicates the number of CPPM entries.
show airgroup debug statistics
The following output is displayed for the show airgroup debug statistics command:
Airgroup slave status :TRUE
Airgroup master status :TRUE
Airgroup multi swarm status :TRUE
status value :0x7f
My ip address :192.168.10.251
My VC address :192.168.10.2
Peer VC address :192.168.10.2
Peer VC address :192.168.20.2
Peer VC address :192.168.30.2
Peer VC address :192.168.40.2
Peer VC address :0.0.0.0
Peer VC address :0.0.0.0
Peer VC address :0.0.0.0
Peer VC address :0.0.0.0
AirGroup Debug Statistics
-------------------------Key Value
--- ----network cache init counter 2(2)
194 | show airgroup
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
mdns apdb init counter 7(7)
mdns apdb destroy counter 1(1)
user timed out 1(1)
airgroup restore count 1(1)
mdns mac move counter 4(4)
mdns master to vc hello rx 2060(2060)
mdns slave to slave hello rx 8240(8240)
mdns ap to ap mac sync resp rx 57(57)
mdns master to vc mac req rx 1580(1580)
swarm update counter rx 1(1)
mdns recieved valid swarm packet 11978(11978)
mdns recieved dlna pkt from device 177704(177704)
mdns partial hello tx 2059(2059)
mdns ap update tx 80(80)
mdns master to vc mac sync resp tx 232(232)
mdns ap to ap mac sync resp tx 1348(1348)
dropped init not done tx 6(6)
master to vc hello tx 2059(2059)
master to my swarm hello tx 2354(2354)
mdns ap to swarm hello tx 4118(4118)
mdns slave to slave mac sync req tx 57(57)
mdns total pkt sent to asap tx 112563(112563)
hello ap verification fail count 1(1)
The output of this command provides the following information:
Column
Description
Airgroup slave status
Indicates the AirGroup configuration status on the slave W-IAP.
Airgroup master status
Indicates the AirGroup configuration status on the slave W-IAP.
Airgroup multi swarm status
Indicates the status of the inter cluster mobility.
status value
Indicates the status value.
Key and Value
Displays details of AirGroup counters.
show airgroup internal-state statistics
The following output is displayed for the show airgroup internal-state statistics command:
Time: Fri May 16 09:30:22 2014
RADIUS Client Messages
---------------------Type Sent Since Last Read Sent Total Recv Since Last Read Recv Total
---- -------------------- ---------- -------------------- ---------Auth Req/Resp 0 0 0 0
RFC3576 N/A N/A 0 0
CPPM Device-Entry Added N/A N/A 0 0
CPPM Device-Entry Deleted N/A N/A 0 0
Internal MDNS Statistics
-----------------------Functionality Hit Count Since Last Read Hit Count Total Average Time in microsec (since last
read) Average Time in microsec (alltime)
------------- ------------------------- --------------- ----------------------------------------- ---------------------------------Response - Cache Update 0 0 0 0
Response 0 0 0 0
Query - prepare records + Policy 0 0 0 0
Query - Policy 0 0 0 0
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show airgroup | 195
Query - resp pkt gen & send 0 0 0 0
Query - Response packet send 0 0 0 0
Query 0 0 0 0
Internal DLNA Statistics
-----------------------Functionality Hit Count Since Last Read Hit Count Total Average Time in microsec (since last
read) Average Time in microsec (alltime)
------------- ------------------------- --------------- ----------------------------------------- ---------------------------------Response - Cache Update 0 0 0 0
Response 0 0 0 0
Query - prepare records + Policy 0 0 0 0
Query - Policy 0 0 0 0
Query - resp pkt gen & send 0 0 0 0
Query - Response packet send 0 0 0 0
Query 0 0 0 0
The output of this command displays information about queries and responses, and RADIUS client messages.
show airgroup servers
The following output is displayed for the show airgroup servers command:
AirGroup Servers
---------------MAC IP Type Host Name Service VLAN Wired/Wireless Role Group Username AP-Name
--- -- ---- --------- ------- ---- -------------- ---- ----- -------- ------Num Servers: 0, Max Servers: 80.
The output of this command provides the following information:
Column
Description
MAC
Indicates the MAC address of the AirGroup servers.
IP
Indicates the IP address of the AirGroup servers.
Type
Indicates the type of server.
Hostname
Indicates the hostname of the AirGroup servers.
Service
Indicates if AirGroup services such as AirPlay or AirPrint are configured.
VLAN
Displays VLAN details of the AirGroup servers.
Wired/Wireless
Displays if the AirGroup server is connected to a wired or wireless interface.
Role
Displays the user role details.
Group
Displays the server group.
Username
Displays the username details.
AP-name
Displays the name of the AP.
Num servers
Displays the total number of servers.
Max Servers
Displays the maximum number of servers that are supported.
196 | show airgroup
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show airgroup status
The following output is displayed for the show airgroup status command:
AirGroup Feature
---------------Status
-----Disabled
AirGroup- MDNS Feature
---------------------Status
-----Disabled
AirGroup- DLNA Feature
---------------------Status
-----Disabled
AirGroup Multi Swarm
-------------------Status
-----Disabled
AirGroup Guest Multicast
-----------------------Status
-----Disabled
CPPM Parameters
--------------Parameter Value
--------- ----CPPM Enforce Registration Disabled
CPPM Server query interval 10 Hours
CPPM Server dead time 100 Seconds
AirGroup Service Information
---------------------------Service Status
------- -----airplay Disabled
airprint Disabled
itunes Disabled
remotemgmt Disabled
sharing Disabled
chat Disabled
Chromecast Disabled
DLNA Media Disabled
DLNA Print Disabled
allowall Disabled
The output of this command provides the following information:
Column
Description
Airgroup feature status
Indicates if the AirGroup feature such as DLNA or MDNS support is
enabled.
AirGroup Multi Swarm status
Indicates if the inter cluster mobility is enabled.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show airgroup | 197
Column
Description
AirGroup Guest Multicast
Indicates if a guest VLAN is used for Bonjour services.
CPPM Parameters
Displays CPPM configuration parameters associated with the AirGroup
configuration.
AirGroup Service Information
Displays information about the status of the AirGroup services
configuration.
show airgroup swarm-info
The following output is displayed for show airgroup swarm-info command:
AirGroup Swarm info
-------------------Swarm id
-------ef7501af01cd098223100f6d02733552765515ffcd7712c41c
AirGroup Swarm AP info
----------------------Ap MAC Ap Name Ap Ip Update no
------ ------- ----- --------6c:f3:7f:c3:5c:12 6c:f3:7f:c3:5c:12 10.17.141.140 0x3
d8:c7:c8:cb:d3:b8 d8:c7:c8:cb:d3:b8 10.17.141.138 0x0
d8:c7:c8:cb:d3:9c d8:c7:c8:cb:d3:9c 10.17.141.139 0x0
d8:c7:c8:cb:d4:20 d8:c7:c8:cb:d4:20 10.17.141.137 0x0
AirGroup Swarm AP's Client info
-------------------------------Mac Ip Update no Record Hash APs Mac
--- -- --------- ----------- ------9c:20:7b:df:3e:8a 10.17.141.141 0x1 0x12cc1003 6c:f3:7f:c3:5c:12
The output of this command displays the AirGroup cluster information.
show airgroup users
The following output is displayed for the show airgroup users command:
AirGroup Users
-------------MAC IP Host Name VLAN Wired/Wireless Role Username AP-Mac Query/Resp
--- -- --------- ---- -------------- ---- -------- ------ ---------Num Users:0
The output of this command provides the following information:
Column
Description
MAC
Indicates the MAC address of the AirGroup clients.
IP
Indicates the IP address of the AirGroup clients.
Host Name
Indicates the hostname of the AirGroup clients.
VLAN
Displays VLAN details of the AirGroup clients.
198 | show airgroup
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Column
Description
Wired/Wireless
Displays if the AirGroup user is connected to a wired or wireless interface.
Role
Indicates the AirGroup user role.
Username
Displays the username of the AirGroup user.
AP-Mac
Displays the MAC address of the W-IAP to which the user is connected.
Query/Resp
Displays information query and response details exchanged between the AirGroup
user and the AirGroup server.
Num Users
Indicates the number of AirGroup users.
Command History
Version
Description
Dell Networking W-Series Instant 6.4.0.2-4.1
This command was modified.
Dell Networking W-Series Instant 6.3.1.1-4.0
This command was modified.
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show airgroup | 199
show airgroupservice
show airgroupservice [disallow {role| vlan}]
Description
This command displays the AirGroup service configuration details for a W-IAP.
Syntax
Parameter
Description
show airgroupservice
Displays a summary of the configuration details for AirGroup services.
disallow {role |vlan}
Displays the user roles or VLANs that are restricted from accessing AirGroup
services. When the access to AirGroup services is restricted, the clients that are
assigned with a specific role or VLAN will not be able to use the AirGroup
service.
Usage Guidelines
Use the show airgroupservice command to view the AirGroup services configured on a W-IAP.
Examples
The following output is displayed for the show airgroupservice command:
AirGroupService Details
----------------------Service Description status Disallowed-Role Disallowed-VLAN ID
------- ----------- ------ --------------- --------------- -airplay AirPlay Disabled _airp lay._tcp
_raop ._tcp
_appl etv-v2._tcp
airprint AirPrint Disabled _ipp. _tcp
_pdl- datastream._tcp
_prin ter._tcp
_scan ner._tcp
_univ ersal._sub._ipp._tcp
_univ ersal._sub._ipps._tcp
_prin ter._sub._http._tcp
_http ._tcp
_http -alt._tcp
_ipp- tls._tcp
_fax- ipp._tcp
_riou sbprint._tcp
_cups ._sub._ipp._tcp
_cups ._sub._fax-ipp._tcp
_ica- networking._tcp
_ptp. _tcp
_cano n-bjnp1._tcp
_ipps ._tcp
_ica- networking2._tcp
itunes iTunes Disabled _home -sharing._tcp
_appl e-mobdev._tcp
_daap ._tcp
_dacp ._tcp
remotemgmt Remote management Disabled _ssh. _tcp
_sftp -ssh._tcp
_ftp. _tcp
_teln et._tcp
200 | show airgroupservice
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
_rfb. _tcp
_net- assistant._tcp
AirGroupService Details
----------------------Service Description status Disallowed-Role Disallowed-VLAN ID
------- ----------- ------ --------------- --------------- -sharing Sharing Disabled _odi sk._tcp
_afp overtcp._tcp
_xgr id._tcp
chat Chat Disabled _pre sence._tcp
Chromecast Chromecast Disabled urn: dial-multiscreen-org:service:dial:1
urn: dial-multiscreen-org:device:dial:1
DLNA Media Media Disabled urn: schemas-upnp-org:device:MediaServer:1
urn: schemas-upnp-org:device:MediaServer:2
urn: schemas-upnp-org:device:MediaServer:3
urn: schemas-upnp-org:device:MediaServer:4
urn: schemas-upnp-org:device:MediaRenderer:1
urn: schemas-upnp-org:device:MediaRenderer:2
urn: schemas-upnp-org:device:MediaRenderer:3
urn: schemas-upnp-org:device:MediaPlayer:1
DLNA Print Print Disabled urn: schemas-upnp-org:device:Printer:1
urn: schemas-upnp-org:service:PrintBasic:1
urn: schemas-upnp-org:service:PrintEnhanced:1
allowall Remaining-Services Disabled
Num Services:10
Num Service-ID:49
The following example shows the partial output displayed for the show airgroupservice disallow role command:
airplay
------default_wired_port_profile
port
airprint
-------default_wired_port_profile
port
The following example shows the partial output displayed for the show airgroupservice disallow vlan command:
airplay
------1
100
200
airprint
-------1
100
200
Command History
Version
Description
Dell Networking W-Series
Instant 6.4.0.2-4.1
This command is modified.
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show airgroupservice | 201
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
202 | show airgroupservice
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show airgroupservice-ids
show airgroupservice-ids <service>
Description
This command displays the AirGroup service IDs configured on a W-IAP for its AirGroup clients.
Syntax
Parameter
Description
service
Indicates the name of the service and displays the service ID details of specified
AirGroup service.
Usage Guidelines
Use the show airgroupservice command to view the IDs of the AirGroup services configured on a W-IAP.
Examples
The following output is displayed for the show airgroupservice-ids command for the AirPlay service:
(Instant AP)# show airgroupservice-ids airplay
airplay
------Service ids
----------_airplay._tcp
_raop._tcp
_appletv-v2._tcp
The output of this command displays the service IDs associated with the AirGroupservice.
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.1-4.0
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show airgroupservice-ids | 203
show acl
show acl {domains}
Description
This command displays the Access Control List (ACL) configuration details.
Syntax
Parameter
Description
domains
Displays the domains configured with an access control list.
Usage Guidelines
Use this command to view the ACL configuration details.
Example
The following example shows the output of the show acl command:
(Instant AP)# show acl
role-domain
----------role-domain inused
----------- -----d8:c7:c8:c4:42:98#
The output of this command displays information about the role-domain.
Command History
Version
Description
Dell Networking W-Series Instant
6.4.0.2-4.1
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
204 | show acl
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ale
show ale {config| status}
Description
This command displays the ALE configuration details.
Syntax
Parameter
Description
config
Displays the ALE configuration details.
status
Displays the status of ALE server.
Usage Guidelines
Use this command to view the ALE configuration status.
Example
The following example shows the output of the show ale config command:
(Instant AP)# show ale config
ALE Config
---------Type Value
---- ----ale-server AleServer1
ale-report-interval 60
The output of this command displays the ALE server details and the reporting interval at which the Virtual Controller
sends data to the ALE server.
The following example shows the output of the show ale status command:
(Instant AP)# show ale status
ALE Status
---------Type Value
---- ----ale login status False
ale login status code
ale fail times 0
ale request state Idle
The output of this command displays information about the ALE server status and data request status.
Command History
Version
Description
Dell Networking W-Series Instant
6.3.1.1-4.0
This command is introduced.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ale | 205
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
206 | show ale
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show alert global
show alert global [count]
Description
This command displays the list of client alerts for a W-IAP.
Syntax
Parameter
Description
<count>
Filters client alerts based on the specified number.
Usage Guidelines
Use this command to view the client alerts for a W-IAP. The client alerts occur when clients are connected to the
Instant network. Alerts are generated when a client encounters problems while accessing or connecting to the WIAP network.
Example
The show alerts global command displays information about the clients for which alerts (if any) are generated. The
following example shows the output for the show alerts global command when no client alerts are generated.
Client Alerts
------------Timestamp Type MAC Address Description Access Point
--------- ---- ----------- ----------- ------------
The output of this command provides the following information:
Parameter
Description
Timestamp
Displays the time at which the client alert was recorded.
MAC Address
Displays the MAC address of the client that caused the alert.
Description
Provides a short description of the alert.
Access Point
Displays the IP address of the W-IAP to which the client is connected.
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show alert global | 207
show alg
show alg
Description
This command displays the Application Layer Gateway (ALG) protocol information configured on a W-IAP.
Usage Guidelines
Use this command to view configuration details for the ALG protocols. An application-level gateway consists of a
security component that augments a firewall or NAT used in a network.
Example
The following output is displayed for the show alg command:
Current ALG
----------ALG Status
--- -----sccp Enabled
sip Enabled
vocera Enabled
The output of this command displays if the ALG protocols such as Skinny Call Control Protocol (SCCP), Session
Initiation Protocol (SIP), and VOCERA are enabled.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
208 | show alg
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show allowed-aps
show allowed-aps
Description
This command displays the list of W-IAPs that are allowed to join the W-IAP cluster.
Usage Guidelines
Use this command to view the W-IAP whitelist.
Example
The following example shows the output of the show allowed-aps command:
Allow New APs :enable
AP Whitelist
-----------MAC Address
----------d8:c7:c8:cb:d4:20
d8:c7:c8:cb:d3:98
d8:c7:c8:cb:d3:b4
d8:c7:c8:cb:d3:d4
The output of this command provides the following information:
Parameter
Description
Allow New APs
Indicates if the new W-IAPs are allowed to join the network.
MAC Address
Displays the MAC address of the W-IAPs that are allowed to join the network.
Command History
Version
Description
Dell Networking WSeries Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show allowed-aps | 209
show all monitor
show all monitor active-laser-beams
Description
This command shows information for Dell Networking W-Series Instant Air Monitors.
Usage Guidelines
Use this command to view the information on Dell Networking W-Series Instant Air Monitors.
Syntax
Parameter
Description
active-laser-beams
Show active laser beam generators.
The output of this command shows a list of all W-IAPs that are actively
performing policy enforcement containment such as rogue containment. This
command can tell us which W-IAP is sending out deauthorization frames,
although it does not specify which W-IAP is being contained.
Example
The following example shows the output of show all monitor command.
Swarm Active Laser Beam Sources
------------------------------bssid channel rssi ap name lms ip master ip inactive time reported by
----- ------- ---- ------- ------ --------- ------------- -----------
Command History
Version
Description
Dell Networking W-Series
Instant 6.4.0.2-4.1
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
210 | show all monitor
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show amp-audit
show amp-audit
Description
This command displays the set of configurations on the W-AirWave Management Platform.
Usage Guidelines
Use this command to view the AMP related configurations.
Example
The following example shows the output of the show amp-audit command:
rule any any match any any any deny
wlan access-rule ssid1
index 3
rule any any match any any any deny
hotspot anqp-nai-realm-profile "name1"
enable
nai-realm-name ""
nai-realm-eap-method eap-ttls
nai-realm-auth-id-1 non-eap-inner-auth
nai-realm-auth-value-1 mschapv2
nai-realm-auth-id-2 credential
nai-realm-auth-value-2 uname-password
nai-realm-encoding utf8
no nai-home-realm
hotspot anqp-nai-realm-profile "nr1"
enable
nai-realm-name "name1"
nai-realm-eap-method eap-sim
nai-realm-auth-id-1 non-eap-inner-auth
nai-realm-auth-value-1 mschapv2
nai-realm-auth-id-2 credential
nai-realm-auth-value-2 uname-password
nai-realm-encoding utf8
nai-home-realm
hotspot anqp-venue-name-profile "Vn1"
enable
venue-group business
venue-type research-and-dev-facility
venue-lang-code en
venue-name ""
hotspot anqp-venue-name-profile "vn1"
enable
venue-group business
venue-type research-and-dev-facility
venue-lang-code eng
venue-name "vn1"
hotspot anqp-nwk-auth-profile "na1"
enable
nwk-auth-type accept-term-and-cond
url "www.nwkauth.com"
hotspot anqp-roam-cons-profile "rc1"
enable
roam-cons-oi-len 3
roam-cons-oi "888888"
hotspot anqp-3gpp-profile "3g"
enable
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show amp-audit | 211
3gpp-plmn1 "40486"
3gpp-plmn2 ""
3gpp-plmn3 ""
3gpp-plmn4 ""
3gpp-plmn5 ""
3gpp-plmn6 ""
hotspot anqp-ip-addr-avail-profile "ip1"
enable
ipv4-addr-avail
no ipv6-addr-avail
hotspot anqp-domain-name-profile "dn1"
enable
domain-name "DomainName"
hotspot h2qp-oper-name-profile "on1"
enable
op-lang-code eng
op-fr-name "FriendlyName"
hotspot hs-profile "hs1"
enable
comeback-mode
no asra
no internet
pame-bi
group-frame-block
p2p-dev-mgmt
no p2p-cross-connect
addtl-roam-cons-ois 0
gas-comeback-delay 10
query-response-length-limit 20
access-network-type chargeable-public
venue-group business
venue-type research-and-dev-facility
roam-cons-len-1 3
roam-cons-oi-1 "123456"
roam-cons-len-2 3
roam-cons-oi-2 "223355"
roam-cons-len-3 0
roam-cons-oi-3 ""
advertisement-profile anqp-nai-realm "nr1"
wlan ssid-profile test
enable
index 0
type employee
essid instant
opmode opensystem
max-authentication-failures 0
rf-band all
captive-portal disable
dtim-period 1
inactivity-timeout 1000
broadcast-filter none
dmo-channel-utilization-threshold 90
local-probe-req-thresh 0
max-clients-threshold 64
dot11k
dot11v
wlan ssid-profile ssid1
enable
index 1
type employee
essid hsProf
opmode wpa2-aes
212 | show amp-audit
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
max-authentication-failures 0
vlan 200
rf-band all
captive-portal disable
mac-authentication
l2-auth-failthrough
dtim-period 1
inactivity-timeout 1000
broadcast-filter none
radius-accounting
blacklist
dmo-channel-utilization-threshold 90
local-probe-req-thresh 0
max-clients-threshold 64
hotspot-profile "hs1"
auth-survivability cache-time-out 24
wlan external-captive-portal
server localhost
port 80
url "/"
auth-text "Authenticated"
auto-whitelist-disable
https
blacklist-time 3600
auth-failure-blacklist-time 3600
ids
wireless-containment none
wired-port-profile wired-instant
switchport-mode access
allowed-vlan all
native-vlan guest
no shutdown
access-rule-name wired-instant
speed auto
duplex auto
no poe
type guest
captive-portal disable
no dot1x
wired-port-profile default_wired_port_profile
switchport-mode trunk
allowed-vlan all
native-vlan 1
shutdown
access-rule-name default_wired_port_profile
speed auto
duplex full
no poe
type employee
captive-portal disable
no dot1x
enet0-port-profile default_wired_port_profile
uplink
preemption
enforce none
failover-internet-pkt-lost-cnt 10
failover-internet-pkt-send-freq 30
failover-vpn-timeout 180
airgroup
disable
airgroupservice airplay
disable
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show amp-audit | 213
description AirPlay
airgroupservice airprint
disable
description AirPrint
per-ap-settings d8:c7:c8:c4:42:98
hostname d8:c7:c8:c4:42:98
ip-address 10.17.161.254 255.255.255.0 10.17.161.1 10.13.6.110 ""
swarm-mode cluster
wifi0-mode access
wifi1-mode access
g-channel 0 0
a-channel 0 0
uplink-vlan 0
g-external-antenna 0
a-external-antenna 0
The output of this command provides the following information:
Command History
Version
Description
Dell Networking WSeries Instant
6.4.0.2-4.1
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
214 | show amp-audit
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap-env
show ap-env
Description
This command displays all provisioned AP parameters such as the type of antenna used by a. The output of this
command also indicates if the W-IAP is provisioned as a master W-IAP.
Usage Guidelines
Use this command to view the antenna configuration details for a W-IAP.
Example
The following output is displayed for the show ap-env command:
Antenna Type:Internal
Iap_master:1
The output of this command indicates if the W-IAP is configured to use an external or integrated antenna and if the
W-IAP is configured as a master W-IAP.
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.1-4.0
This command is modified.
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap-env | 215
show aps
show aps [scanning][sync]
Description
This command displays all active W-IAPs, W-IAP scanning, and synchronization status.
Syntax
Parameter
Description
aps
Displays the list of all active W-IAPs in the cluster.
aps scanning
Displays W-IAP scanning details.
aps sync
Displays W-IAP synchronization details.
Usage Guidelines
Use this command to view the list of active W-IAPs, W-IAP scanning and synchronization details.
Example
The following output is displayed for the show aps command:
AP List
------Name IP Address Mode Spectrum Clients Type Mesh Role 2.4 Channel
---- ---------- ---- -------- ------- ---- --------- ---------d8:c7:c8:cb:d4:20 10.17.88.188 access disable 1 135 Portal 7
2.4 Power (dB) 2.4 Utilization (%) 2.4 Noise Floor (dBm) 5.0 Channel 5.0 Power (dB)
--------------- ------------------- --------------------- ---------- -----------21 52(ok) -91(good) 44+ 22
5.0 Utilization (%) 5.0 Noise Floor (dBm) Need Antenna Config From Port Config Id
------------------- ---------------------- ------------------- --------- -----3(good) -91(good) No none 1
The output of this command includes the following parameters:
Column
Description
Name
Displays the Name of the W-IAPs.
IP address
Displays the IP address of the W-IAPs.
Mode
Displays the operating mode. For example, access, monitor, or spectrum monitor
modes.
Spectrum
Indicates if spectrum monitoring is enabled or disabled.
Client
Indicates the number of client associated with the W-IAP.
Type
Displays the W-IAP model.
216 | show aps
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Column
Description
Mesh Role
Indicates if the W-IAP is functioning as Mesh Point or mesh Portal.
2.4 Channel
Indicates the channels used by the W-IAP in the 2.4 GHz band.
2.4 Power(dB)
Indicates the transmission power allocated for 2.4 Ghz band channels.
2.4 Utilization
Indicates the percentage of utilization of 2.4 GHz channels.
2.4 Noise Floor
Indicates the noise floor of the 2.4 GHz channels.
5.0 Channel
Indicates the channels used by the W-IAP in the 5 GHz band.
5.0 Power(dB)
Indicates the transmission power allocated for 5 GHz band channels.
5.0 Utilization
Indicates the percentage of utilization of 5 GHz channels.
5.0 Noise Floor
Indicates the noise floor of the 5 GHz channels.
Need antenna config
Indicates if antenna configuration is required.
From port
Indicates the port details if any.
Config Id
Indicates the configuration ID.
The following output is displayed for the show aps scanning command:
AP Scanning Stats
----------------Name IP Address 2.4 Reqs 2.4 Voice Rejs 2.4 Video Rejs 5.0 Reqs
---- ---------- -------- -------------- -------------- ----d8:c7:c8:cb:d4:20 10.17.88.188 5665 0 0 5675
5.0 Voice Rejs 5.0 Video Rejs
-------------- -------------0 0
The output of this command includes the following parameters:
Column
Description
Name
Displays the Name of the W-IAP.
IP address
Displays the IP address of the W-IAP.
2.4 Reqs
Displays the counters that indicate channel scanning requirements.
5.0 Reqs
2.4 Voice Rejs
5.0 Voice Rejs
2.4 Video Rejs
5.0 Video Rejs
Displays the counters that indicate the number of scanning rejects due to voice
traffic.
Displays the counters that indicate the number of scanning rejects due to voice
traffic.
The following output is displayed for the show aps scanning command:
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show aps | 217
AP Sync List
-----------MAC IP Address Class Current Version
--- ---------- ----- ---------------
The output of this command includes the following parameters:
Column
Description
MAC
Indicates MAC address of the W-IAP with which the current W-IAP is synchronized.
IP address
Displays the IP address of the W-IAP.
Class
Indicates if the W-IAP is serving as master or slave.
Current Version
Displays the Instant version currently running on the W-IAP.
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
218 | show aps
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap allowed-channels
show ap allowed-channels <country-code>
Description
This command displays a list of allowed channels for a W-IAP.
Syntax
Parameter
Description
<country-code>
Specify a country code to display allowed channels for that country.
Usage Guidelines
Specify the country code for your W-IAP during the initial setup. Changing the country code causes the valid channel
lists to be reset to the defaults for that country.
Example
The following example shows the output of the show ap allowed-channels US command:
Allowed Channels for Country Code "US"
-------------------------------------PHY Type Allowed Channels
-------- ---------------802.11g (indoor) 1 2 3 4 5 6 7 8 9 10 11
802.11a (indoor) 36 40 44 48 149 153 157 161 165
802.11g (outdoor) 1 2 3 4 5 6 7 8 9 10 11
802.11a (outdoor) 149 153 157 161 165
802.11g 40MHz (indoor) 1-5 2-6 3-7 4-8 5-9 6-10 7-11
802.11a 40MHz (indoor) 36-40 44-48 149-153 157-161
802.11g 40MHz (outdoor) 1-5 2-6 3-7 4-8 5-9 6-10 7-11
802.11a 40MHz (outdoor) 149-153 157-161
The output of this command includes the following information:
Parameter
Description
PHY Type
Indicates the PHY types for the following bands: types:
Allowed Channels
l
802.11a
l
802.11g
Displays the list of allowed channels for a specific regulatory domain.
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap allowed-channels | 219
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
220 | show ap allowed-channels
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap allowed-max-EIRP
show ap allowed-max-EIRP [<country>]
Description
This command displays the maximum EIRP settings for the country in which the W-IAP is currently operational. You
can also view the maximum EIRP settings for a specific country.
Syntax
Parameter
Description
[<country>]
Displays the EIRP settings allowed for a specific country.
Usage Guidelines
Use this command to view the maximum EIRP settings for a W-IAP. You can also filter the output to view the EIRP
settings for a specific country.
Example
The following example shows the output of the show ap allowed-max-EIRP <country> command:
Max EIRP setting for Country Code US Country United States and AP type AP-105
----------------------------------------------------------------------------Channel 1 2 3 4 5 6 7 8 9 10 11 12 13 14 36 40 44 48 52 56 60 64 100 104 108 112 116 120 124
128 132 136 140 149 153 157 161 165
------- - - - - - - - - - -- -- -- -- -- -- -- -- -- --- --- --b 20 20 20 20 20 20 20 20 20 20 20 * * * * * * * * * * * * * * * * * * * * * * * * * * *
g/a 22 22 22 22 22 22 22 22 22 22 22 * * * 22 22 22 22 24 24 24 24 22 22 22 22 22 * * * 22 22
22 23 23 23 23 23
HT 20 22 22 22 22 22 22 22 22 22 22 22 * * * 21 21 21 21 24 24 24 24 22 22 22 22 22 * * * 22
22 22 22 23 24 24 24
HT 40 19 19 20 21 22 23 22 22 22 21 21 * * * 20 20 20 20 23 23 23 23 22 22 22 22 * * * * 22 22
22 22 22 22 20 17
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap allowed-max-EIRP | 221
show ap arm
show ap arm {bandwidth-management | history | neighbors |rf-summary | scan-times}
Description
This command displays information about bandwidth management, historical statistics, W-IAP neighbors, RF
summary, and scanning details for the W-IAP.
Syntax
Parameter
Description
bandwidth management
Displays ARM bandwidth details for a W-IAP.
history
Displays detailed information about the ARM configuration changes over a
period of time.
neighbors
Displays details about the ARM neighbors.
rf-summary
Displays a summary of RF configuration information for a W-IAP
scan-times
Displays ARM channel scanning details for a W-IAP.
Usage Guidelines
Use this command to view information about the Adaptive Radio Management (ARM) bandwidth configuration,
historical statistics, W-IAP neighbors, RF summary, and scanning details on a W-IAP.
Example
show ap arm bandwidth-management
The following example shows the output of show ap arm bandwidth-management command:
Interface :wifi0
Shaping Table
------------Client Tx Pkt Tx
--- -----------Tx Rate (mbps)
--------Interface :wifi1
Shaping Table
------------Client Tx Pkt Tx
--- -----------Tx Rate (mbps)
---------
Byte (KB) Tx Alloc (ms) Tx Time (ms) Rx Time (ms) Active Time (ms) ------ --------------- ------------ ------------ --------------
Byte (KB) Tx Alloc (ms) Tx Time (ms) Rx Time (ms) Active Time (ms) ------ --------------- ------------ ------------ --------------
The output of this command includes the following information:
Column
Description
Interface
Displays the Wi-F interface configured on the W-IAP.
Shaping table
Displays information on the ARM configuration details for the clients associated
with the W-IAP.
222 | show ap arm
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Column
Description
Client
Displays the list of W-IAP clients connected through the Wi-Fi interface.
Tx Pkt
Displays the transmission packet details associated with the interface.
Tx Byte
Displays the number of bytes in the transmission packets associated with the
interface.
Tx Alloc (ms)
Indicates the time allocated for transmission in milliseconds.
Tx Time (ms)
Indicates the transmission time in milliseconds.
Rx Time (ms)
Indicates the reception time in milliseconds.
Active time (ms)
Indicates duration until which the Wi-Fi devices are active.
Tx Rate (Mbps)
Indicates the current speed at which data is transmitted through the Wi-Fi
interface.
show ap arm history
For each interface on a W-IAP, the show ap arm history command shows the history of channel and power
changes due to ARM. ARM can automatically change channel and power levels based on a number of factors such
as noise levels and radio interference. The following example shows the output of the show ap arm history
command:
Interface :wifi0
ARM History
----------Time of Change Old Channel New Channel Old Power New Power Reason
-------------- ----------- ----------- --------- --------- -----2013-05-11 04:24:31 149+ 161- 27 27 I
2013-05-11 02:54:34 157+ 149+ 27 27 I
2013-05-11 02:46:13 153- 157+ 27 27 I
2013-05-11 02:27:11 157+ 153- 27 27 I
2013-05-11 02:22:18 149+ 157+ 27 27 I
2013-05-11 01:35:00 161- 149+ 27 27 I
2013-05-11 01:28:58 149+ 161- 27 27 I
2013-05-10 22:46:33 161- 149+ 27 27 I
2013-05-10 22:38:09 153- 161- 27 27 I
2013-05-10 22:02:10 161- 153- 27 27 I
2013-05-10 21:55:21 153- 161- 27 27 I
2013-05-10 16:47:15 157+ 153- 27 27 I
2013-05-10 16:28:16 149+ 157+ 27 27 I
2013-05-10 15:19:59 161- 149+ 27 27 I
2013-05-10 15:14:29 149+ 161- 27 27 I
2013-05-10 13:10:55 161- 149+ 27 27 I
2013-05-10 13:03:47 149+ 161- 27 27 I
2013-05-10 12:17:34 157+ 149+ 27 27 I
2013-05-10 12:10:21 153- 157+ 27 27 I
2013-05-10 11:12:04 157+ 153- 27 27 I
2013-05-10 11:00:07 149+ 157+ 27 27 I
2013-05-10 10:54:39 157+ 149+ 27 27 I
2013-05-10 10:49:33 149+ 157+ 27 27 I
2013-05-10 10:44:34 157+ 149+ 27 27 I
2013-05-10 10:39:51 149+ 157+ 27 27 I
2013-05-10 10:33:07 157+ 149+ 27 27 I
2013-05-10 10:25:35 149+ 157+ 27 27 I
2013-05-10 09:18:11 157+ 149+ 27 27 I
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap arm | 223
2013-05-10 09:04:24 149+ 157+ 27 27 I
2013-05-10 06:08:59 157+ 149+ 27 27 I
2013-05-10 05:55:10 153- 157+ 27 27 I
2013-05-10 05:11:21 157+ 153- 27 27 I
Interface :wifi1
ARM History
----------Time of Change Old Channel New Channel Old Power New Power Reason
-------------- ----------- ----------- --------- --------- -----2013-05-11 04:16:28 6 1 24 24 I
2013-05-11 03:58:53 11 6 24 24 I
2013-05-11 03:13:44 1 11 24 24 I
2013-05-11 01:23:32 6 1 24 24 I
2013-05-11 01:04:29 11 6 24 24 I
2013-05-11 00:26:16 1 11 24 24 I
2013-05-10 23:13:30 6 1 24 24 I
2013-05-10 23:04:49 11 6 24 24 Q
2013-05-10 22:51:10 6 11 24 24 I
2013-05-10 22:45:01 1 6 24 24 I
2013-05-10 21:52:39 6 1 24 24 I
2013-05-10 21:44:37 1 6 24 24 Q
2013-05-10 21:29:52 6 1 24 24 I
2013-05-10 21:19:16 11 6 24 24 I
2013-05-10 21:12:53 6 11 24 24 I
2013-05-10 20:52:07 1 6 24 24 I
2013-05-10 19:28:09 6 1 24 24 I
2013-05-10 19:02:08 11 6 24 24 I
2013-05-10 18:23:32 1 11 24 24 I
2013-05-10 17:40:55 6 1 24 24 I
2013-05-10 17:28:40 11 6 24 24 I
2013-05-10 17:01:24 1 11 24 24 I
2013-05-10 15:10:19 6 1 24 24 I
2013-05-10 15:03:41 11 6 24 24 I
2013-05-10 14:45:39 6 11 24 24 I
2013-05-10 14:19:32 11 6 24 24 I
2013-05-10 13:37:30 1 11 24 24 I
2013-05-10 11:34:27 6 1 24 24 I
2013-05-10 11:19:52 11 6 24 24 I
2013-05-10 10:30:51 1 11 24 24 I
2013-05-10 09:18:51 6 1 24 24 I
2013-05-10 09:06:31 11 6 24 24 I
I: Interference, R: Radar detection, N: Noise exceeded, Q: Bad Channel Quality E: Error
threshold exceeded, INV: Invalid Channel, G: Rogue AP Containment, M: Empty Channel, P+:
Increase Power, P-: Decrease Power, 40INT: 40MHZ intol detected on 2.4G, NO40INT: 40MHz intol
cleared on 2.4G, OFF: Turn off Radio, ON: Turn on Radio
The output of this command includes the following information:
Column
Description
Time of change
Indicates the timestamp of the channel changes for each interface.
Old Channel
Displays the channel number used by the W-IAP before the ARM change.
New channel
Displays the channel number used by the W-IAP after the ARM change.
Old Power
Indicates power values configured on the W-IAP before the ARM change.
New Power
Indicates power values configured on the W-IAP after the ARM change.
Reason
Indicates the reason for changes in channels. For more information about the
reason, see the description below the command output.
224 | show ap arm
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap arm neighbors
The show ap arm neighbors command displays the ARM settings on the W-IAP neighbors. The following example
shows the output of the show ap arm neighbors command:
ARM Neighbors
------------bssid essid channel rssi tx-power PL (dB) AP Flags Last Update
----- ----- ------- ---- -------- ------- -------- -----------6c:f3:7f:45:57:20 7SPOT 1 8 0 0 Passive
6c:f3:7f:56:7e:a0 7SPOT 1 9 0 0 Passive
6c:f3:7f:56:7e:a1 NTT-SPOT 1 12 0 0 Passive
00:24:6c:80:77:c1 NTT-SPOT 1 9 0 0 Passive
6c:f3:7f:45:57:21 NTT-SPOT 1 8 0 0 Passive
6c:f3:7f:44:91:11 NTT-SPOT 1 9 0 0 Passive
00:24:6c:2b:fd:e8 qa-mv-vap3 161 5 9 98 Passive
00:24:6c:80:4d:62 docomo 1 10 0 0 Passive
(Total updates)
--------------Neighbor Summary:One hop 232 Two hop 0 Current Time: 2013-05-11 04:31:33
The output of this command includes the following information:
Column
Description
bssid
Indicates the BSSID of the W-IAP neighbors.
essid
Indicates the ESSID of the W-IAP neighbors.
Channel
Indicates the channels assigned to the W-IAP neighbors
rssi
Indicates the Received signal strength indication (RSSI) values associated with
the ARM channels to which W-IAP neighbors are connected.
tx power
Indicates the transmission power.
PL
Indicates power loss.
AP Flags
Indicates the status of W-IAP neighbors.
Last Update
Displays details of last updates if any.
Total updates
Displays a summary if updates.
show ap arm rf-summary
The show ap arm rf-summary command shows the statistics for all channels monitored by a W-IAP. The following
example shows the output of the show ap arm rf-summary command:
Channel Summary
--------------channel retry phy-err mac-err
------- ----- ------- ------36 0 0 0 93 3/2/0/0/94 0/0(0)
40 0 0 0 93 9/2/0/0/92 0/0(0)
44 0 0 0 93 2/1/0/1/99 0/0(0)
48 0 0 0 93 9/2/0/0/93 0/0(0)
52 0 0 0 93 0/0/0/0/93 0/0(0)
56 0 0 0 93 5/0/0/0/95 0/0(0)
noise util(Qual) cov-idx(Total) intf_idx(Total)
----- ---------- -------------- --------------97/40//0/0(137)
120/82//0/0(202)
161/88//0/0(249)
157/59//0/0(216)
15/52//0/0(67)
0/18//0/0(18)
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap arm | 225
60 0 0 0 93 0/0/0/0/94 0/0(0) 29/14//0/0(43)
64 0 0 0 93 6/0/0/0/94 0/0(0) 43/10//0/0(53)
149 0 0 0 93 3/2/0/0/99 0/0(0) 113/41//0/0(154)
153 0 0 2 93 23/23/0/1/100 0/0(0) 124/68//0/0(192)
157 0 0 0 93 2/1/0/1/94 0/0(0) 97/79//0/0(176)
161 0 0 5 93 3/2/0/0/99 9/0(9) 115/66//0/0(181)
165 0 0 0 94 10/10/0/0/100 0/0(0) 99/38//0/0(137)
1 0 0 12 78 60/50/3/0/79 8/0(8) 448/79//0/0(527)
6 0 0 0 78 12/11/0/0/81 0/0(0) 483/227//0/0(710)
11 0 0 8 78 71/54/3/16/86 0/0(0) 703/126//0/0(829)
Columns:util(Qual): ch-util/rx/tx/ext-ch-util/quality
HT Channel Summary
-----------------channel_pair Pairwise_intf_index
------------ ------------------149-153 346
36-40 339
157-161 357
44-48 465
Interface Name :wifi0
Current ARM Assignment :161-/27
Covered channels a/g :1/0
Free channels a/g :7/0
ARM Edge State :disable
Last check channel/pwr :2m:36s/4m:24s
Last change channel/pwr :8m:19s/1d:23h:47m:12s
Next Check channel/pwr :2m:36s/2m:15s
Assignment Mode :Single Band
Interface Name :wifi1
Current ARM Assignment :1/24
Covered channels a/g :0/1
Free channels a/g :0/2
ARM Edge State :disable
Last check channel/pwr :5m:31s/3m:33s
Last change channel/pwr :15m:50s/1d:23h:47m:13s
Next Check channel/pwr :16s/2m:33s
Assignment Mode :Single Band
The output of this command includes the following information:
Column
Description
channel
Displays the list of channels enabled on a W-IAP.
retry
Indicates the number of retry attempts.
Phy-err
Indicates the PHY errors on the current channels of a W-IAP.
Mac-err
Indicates the MAC errors on the current channels of a W-IAP.
noise
Displays the current noise level on each channel.
Util (Qual)
Displays the percentage of the channel being used and the current relative
quality of selected channels.
cov-idx(Total)
Displays RF coverage details. The W-IAP uses this metric to measure RF
coverage. The coverage index is calculated as x+y, where “x” is the W-IAP’s
weighted calculation of the Signal-to- Noise Ratio (SNR) on all valid APs on a
specified 802.11 channel, and “y” is the weighted calculation of the W-IAPs SNR
226 | show ap arm
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Column
Description
detected by the neighboring APs on that channel.
intf_idx(Total
Displays channel interference details. The W-IAP uses this metric to measure cochannel and adjacent channel interference. The Interference Index is calculated
as a/b//c/d, where:
l Metric value “a” is the channel interference the AP sees on its selected
channel.
l Metric value “b” is the interference the AP sees on the adjacent channel.
l Metric value “c” is the channel interference the AP’s neighbors see on the
selected channel.
l Metric value “d” is the interference the AP’s neighbors see on the adjacent
channel.
l To calculate the total Interference Index for a channel add “a+b+c+d”.
channel_pair
Displays the list of paired channels.
Pairwise_intf_index
Displays the pairwise interference index.
Interface Name
Displays the interface name.
Current ARM
Assignment
Displays the current ARM assignment details.
Covered channels
Displays the number of channels being used by the W-IAP's BSSID in the 2.4
GHz and 5 GHz bands.
Free channels
Displays the number of available channels in the 2.4 GHz and 5 GHz bands.
ARM Edge State
Displays the ARM Edge status. If ARM edge status is enabled, the ARM-enabled
W-IAPs on the network edge will not function as Air Monitors.
Last check
channel/pwr
Indicates the time since the channel and power assignment was verified.
Last change
channel/pwr
Indicates the time since the channel and power assignment was updated.
Next Check
channel/pwr
Indicates the next interval at which the channel and power assignment will be
verified.
Assignment Mode
Indicates if the ARM is assignment is applicable to a single band or dual band.
show ap arm scan-times
The show ap arm scan-times command shows the AM channel scan times for a W-IAP. The following example
shows the output of the show ap arm scan-times command:
Channel Scan Time
----------------channel assign-time(ms) scans-attempted scans-rejected dos-scans flags timer-tick
------- --------------- --------------- -------------- --------- ----- ---------36 2483300 1530 0 0 DVACFT 172120
40 576170 1547 0 0 DVACPT 172139
44 9945940 1454 0 0 DVACFT 172145
48 170500 1550 0 0 DVACPT 172158
52 167420 1522 0 0 DVACT 172046
56 65450 595 0 0 DVCT 171880
60 169840 1544 0 0 DVACT 172052
64 170390 1549 0 0 DVACT 172063
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap arm | 227
149 68631720 952 0 0 DVACFT 172074
153 32278480 1268 0 0 DVACPT 172088
157 38634770 1207 0 0 DVACFT 172132
161 20620710 1361 0 0 DVACPT 172161
165 170280 1548 0 0 DVACT 172110
1 86424330 903 0 0 DVACFT 172161
2 53570 487 0 0 DC 171936
3 55660 506 0 0 DC 171980
4 88550 805 0 0 DC 172030
5 327140 2974 0 0 DVACP 172124
6 40459820 2562 0 0 DVACT 172110
7 334620 3042 0 0 DVACF 172137
8 89210 811 0 0 DC 171627
9 92620 842 0 0 DC 171684
10 192940 1754 0 0 DAC 172144
11 45787400 1340 0 0 DVACPT 172159
12 132550 1205 0 0 DAC 172051
13 51260 466 0 0 DC 171890
Channel Flags: D: All-Reg-Domain Channel, C: Reg-Domain Channel, A: Activity Present
L: Scan 40MHz Lower, U: Scan 40MHz Upper, Z: Rare Channel
V: Valid, T: Valid 20MHZ Channel, F: Valid 40MHz Channel, P: Valid 40MHZ Channel Pair
O: DOS Channel, K: DOS 40MHz Upper, H: DOS 40MHz Lower
R: Radar detected in last 30 min, X: DFS required
WIF Scanning State
------------------Scan mode channel current-scan-channel last-dos-channel timer-milli-tick
--------- ------- -------------------- ---------------- ---------------Default 161- 48- 0 172161700
Default 1 11- 0 172161700
next-scan-milli-tick (jitter) scans (Tot:Rej:Eff(%):Last intvl(%))
-------------------- -----------------------------------172172520(4420) 17627:0:100:100
172164890(-4108) 17697:0:100:100
The output of this command includes the following information:
Column
Description
channel
Displays the list of channels configured on the W-IAP.
assign-time(ms)
Displays the time since W-IAP is assigned a channel.
scans-attempted
Indicates the number times a W-IAP has attempted to scan another channel.
scans-rejected
Displays the number of times a W-IAP was unable to scan a channel, because
the scan was halted due to other ARM settings.
dos-scans
Indicates the number of times services to a rogue device on a channel were
denied by a W-IAP.
flags
Indicates channel flags. For more information on channel flags, see the flag
description below the channel scan time table.
timer-tick
Indicates the time interval since the last scan.
Scan mode
Indicates if the scan mode enabled on the Wi-Fi interface.
228 | show ap arm
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Column
Description
channel
(under WIFI Scanning
State)
Indicates the channels available on the Wi-Fi interface.
current-scan-channel
Indicates the current channel scanned.
last-dos-channel
Indicates the last channel on which Denial of Service (DOS) was detected.
timer-milli-tick
Indicates the time in milliseconds since the Wi-Fi interface channels were
scanned.
next-scan-milli-tick
(jitter)
Indicates the next interval at which the scanning will begin.
scans (Tot:Rej:Eff
(%):Last intvl(%))
Provides a summary of the Wi-Fi scanning details.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap arm | 229
show ap association
show ap association
Description
This command displays the association table for an AP group or for an individual W-IAP.
Usage Guidelines
Use this command to view information about the clients associated with a W-IAP.
Example
The following example shows the output of show ap association command.
The phy column shows client's operational capabilities for current association
Flags: A: Active, B: Band Steerable, H: Hotspot(802.11u) client, K: 802.11K clie nt, R:
802.11R client, W: WMM client, w: 802.11w client
PHY Details: HT : High throughput; 20: 20MHz; 40: 40MHz
VHT : Very High throughput; 80: 80MHz; 160: 160MHz; 80p80: 80MHz + 80MHz
<n>ss: <n> spatial streams
Association Table
----------------Name bssid mac auth assoc aid l-int essid vlan-id tunnel-id phy assoc.time num assoc ---- ---- --- ---- ----- --- ----- ----- ------- --------- --- ----------- -----Flags
----Num Clients:0
The output of this command includes the following information:
Column
Description
Name
Indicates the Name of a W-IAP or the AP group.
bssid
Indicates Basic Service Set Identifier (BSSID) associated with the W-IAP. The
Basic Service Set Identifier (BSSID) is usually the MAC address of the W-IAP.
mac
Indicates the MAC address of the W-IAP clients.
auth
Displays the status of client authentication. Indicates y if the W-IAP is configured
for 802.11 authorization frame types. Otherwise, it displays an n.
assoc
Displays the status of user association. Indicates y if the W-IAP is configured for
802.11 association frame types. Otherwise, it displays an n.
aid
Indicates 802.11 association ID. A client receives a unique 802.11 association ID
when it associates to a W-IAP.
1-int
Indicates the number of beacons in the 802.11 listen interval. There are ten
beacons sent per second, so a ten-beacon listen interval indicates a listening
interval time of 1 second.
essid
Indicates the name that uniquely identifies the W-IAP’s Extended Service Set
Identifier (ESSID).
vlan-id
Indicates the VLAN ID associated with the W-IAP.
230 | show ap association
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Column
Description
tunnel-id
Indicates the identification number of the W-IAP tunnel.
assoc. time
Indicates the amount of time the client has been associated with the W-IAP, in the
hours:minutes:seconds format.
num assoc
Indicates the number of clients associated with the W-IAP.
flags
Displays flags for this W-IAP if any. For information on flag abbreviations, see the
flag description at beginning of the output.
Num Clients
Indicates the number of clients associated with the W-IAP.
Command History
Version
Description
Dell Networking WSeries Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap association | 231
show ap bss-table
show ap bss-table
Description
This command displays an AP’s Basic Service Set (BSS).
Usage Guidelines
The output of the show ap bss-table command shows the Dell AP BSS table for all APs. To filter this information and
view BSS table data for an individual AP or a specific port and slot number, include the ap-name, bssid, essid, ipaddr or port keywords.
Example
The following example shows the output of show ap bss-table command:
Dell AP BSS Table
-----------------bss ess port ip phy type ch/EIRP/max-EIRP cur-cl ap name in-t(s) tot-t
--- --- ---- -- --- ---- ---------------- ------ ------- ------- ----d8:c7:c8:3d:42:12 example1 ?/? 10.17.88.188 a-HT ap 149+/20/22.5 1 d8:c7:c8:cb:d4:20 0
18h:13m:58s
d8:c7:c8:3d:42:13 example-local-nw ?/? 10.17.88.188 a-HT ap 149+/20/22.5 0 d8:c7:c8:cb:d4:20 0
18h:13m:58s
d8:c7:c8:cb:d4:21 __wired__eth1 ?/? 10.17.88.188 b ap 0/0/0 0 d8:c7:c8:cb:d4:20 0 18h:13m:59s
d8:c7:c8:3d:42:02 example1 ?/? 10.17.88.188 g-HT ap 7/21.5/21.5 0 d8:c7:c8:cb:d4:20 0
18h:13m:58s
d8:c7:c8:3d:42:03 example-local-nw ?/? 10.17.88.188 g-HT ap 7/21.5/21.5 0 d8:c7:c8:cb:d4:20 0
18h:13m:58s
Channel followed by "*" indicates channel selected due to unsupported configured channel.
"Spectrum" followed by "^" indicates Local Spectrum Override in effect.
Num APs:5
Num Associations:1
The output of this command includes the following information:
Column
Description
bss
Displays the AP Basic Service Set Identifier (BSSID). This is usually the MAC address of
the AP.
ess
Displays the AP Extended Service Set Identifier (ESSID).
port
Displays port used by the W-IAP.
ip
Displays the IP address of an AP.
phy
Displays an AP radio type. Possible values are:
type
232 | show ap bss-table
l
a—802.11a
l
a-HT—802.11a high throughput
l
g— 802.11g
l
g-HT—802.11g high throughput
Shows whether the AP is working as an access point (AP) or air monitor (AM).
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Column
Description
ch/EIRP/max-EIRP
Displays the radio channel used by the AP/current effective Isotropic Radiated Power
(EIRP) /maximum EIRP.
cur
Displays the current number of clients on the AP.
Command History
Version
Description
Dell Networking WSeries Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap bss-table | 233
show ap client-match-history
show ap client-match-history [client-mac <mac-address>]
Description
This command displays a historical record of the client match events and actions for the clients associated with a WIAP.
Syntax
Parameter
Description
client-mac <mac-address>
Allows you to filter the output based on a client MAC address. When the
client MAC address is specified and the command is executed, the client
match actions pertaining to the specified client is displayed.
Usage Guidelines
Use this command to view the history of clients match actions for the clients associated with a W-IAP.
Example
The following example shows the output of show ap client-match-history command:
Client Match Action Table
------------------------Station Old State New State Reason Radio Time
------- --------- --------- ------ ----- ---00:db:df:0a:57:4e Normal Normal Client associated 1 18h:32m:5s
00:db:df:0a:57:4e Normal Normal Client associated 0 15h:20m:1s
00:db:df:0a:57:4e Normal Normal Client associated 0 9h:48m:57s
00:db:df:0a:57:4e Normal Target I am the better AP 0 7m:9s
00:db:df:0a:57:4e Normal Deny I am not the better AP 1 7m:9s
a0:88:b4:41:64:18 Normal Deny I am not the better AP 0 5m:20s
a0:88:b4:41:64:18 Normal Deny I am not the better AP 1 5m:20s
00:db:df:0a:57:4e Target Adopted Client match succeed 0 5m:17s
00:db:df:0a:57:4e Deny Normal Client match succeed 1 5m:17s
a0:88:b4:41:64:18 Deny Normal State aged out 0 2m:27s
a0:88:b4:41:64:18 Deny Normal State aged out 1 2m:23s
Total 11 Records
00:24:6c:c8:74:4c# show ap client-match-his client-mac 00:db:df:0a:57:4e
Client Match History for 00:db:df:0a:57:4e
-----------------------------------------Old State New State Reason Radio Time
--------- --------- ------ ----- ---Normal Normal Client associated 1 18h:32m:5s
Normal Normal Client associated 0 15h:20m:1s
Normal Normal Client associated 0 9h:48m:57s
Normal Target I am the better AP 0 7m:9s
Normal Deny I am not the better AP 1 7m:9s
Target Adopted Client match succeed 0 5m:17s
Deny Normal Client match succeed 1 5m:17s
Total 7 Records
234 | show ap client-match-history
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command History
Version
Description
Dell Networking W-Series
Instant 6.3.1.1-4.0
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap client-match-history | 235
show ap client-match-live
show ap client-match-live
Description
This command displays the current client match events and actions for clients associated with a W-IAP.
Usage Guidelines
Use this command to view the current clients match actions for the clients associated with a W-IAP.
Example
The following example shows the output of the show ap client-match-live command.
Client Match Table
-----------------Station CM State RSSI Radio Home AP Target AP Time
------- -------- ---- ----- ------- --------- ---00:db:df:0a:57:4e Adopted 47 0 - - 5m:17s
Total 1 Client Matches
00:24:6c:c8:74:4c# show ap client-match-his
Client Match Action Table
------------------------Station Old State New State Reason Radio Time
------- --------- --------- ------ ----- ---00:db:df:0a:57:4e Normal Normal Client associated 1 18h:32m:5s
00:db:df:0a:57:4e Normal Normal Client associated 0 15h:20m:1s
00:db:df:0a:57:4e Normal Normal Client associated 0 9h:48m:57s
00:db:df:0a:57:4e Normal Target I am the better AP 0 7m:9s
00:db:df:0a:57:4e Normal Deny I am not the better AP 1 7m:9s
a0:88:b4:41:64:18 Normal Deny I am not the better AP 0 5m:20s
a0:88:b4:41:64:18 Normal Deny I am not the better AP 1 5m:20s
00:db:df:0a:57:4e Target Adopted Client match succeed 0 5m:17s
00:db:df:0a:57:4e Deny Normal Client match succeed 1 5m:17s
a0:88:b4:41:64:18 Deny Normal State aged out 0 2m:27s
a0:88:b4:41:64:18 Deny Normal State aged out 1 2m:23s
Total 11 Records
Command History
Version
Description
Dell Networking WSeries Instant
6.3.1.1-4.0
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
236 | show ap client-match-live
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap client-probe-report
show ap client-probe-report [<radio>]
Description
This command displays the client probe report for a W-IAP.
Syntax
Parameter
Description
<radio>
Allows you to filter the output based the ID number of the radio (for example, 0 or
1).
Usage Guidelines
Use this command to view a probe report for the clients associated with a W-IAP.
Example
The following example shows the output of the show ap client-probe-report command.
AP Client Probe Report for Wifi0
-------------------------------MAC RSSI In Swarm Received
--- ---- -------- -------12:c6:00:04:00:00 45 No 36s
12:22:00:00:00:63 44 No 4s
12:3c:00:04:00:00 44 No 1s
02:88:00:00:00:02 44 No 1m:3s
12:ce:00:00:40:00 44 No 27s
12:4c:00:04:00:00 40 No 42s
02:10:00:00:00:06 34 No 40s
00:26:c6:bd:50:96 37 No 45s
08:ed:b9:e1:51:8b 47 No 1h:49m:18s
00:eb:2d:a5:a1:17 51 No 11h:59m:22s
00:19:77:71:41:20 28 No 2m:24s
12:13:00:00:11:10 38 No 59s
24:77:03:11:71:bc 19 No 2s
c4:85:08:dd:f1:58 46 No 55s
08:ed:b9:e1:52:19 56 No 9h:9m:30s
84:85:06:a0:62:86 16 No 5s
00:24:d7:ac:42:78 19 No 1m:38s
b4:b6:76:42:33:fd 32 No 46s
24:77:03:cf:f4:64 19 No 7h:15m:33s
1c:ab:a7:3f:d4:36 12 No 10m:28s
b4:b6:76:42:34:07 13 No 21s
e0:b9:ba:de:04:f1 11 No 12m:49s
b4:b6:76:42:54:28 50 No 44s
24:77:03:7a:85:24 11 No 8h:31m:1s
c4:85:08:de:45:0e 40 No 49s
c4:85:08:de:35:5a 32 No 58s
c4:85:08:de:45:22 33 No 58s
b4:b6:76:42:55:ea 40 No 59s
b4:b6:76:42:55:b8 49 No 27s
b4:b6:76:42:36:af 51 No 0s
b4:b6:76:42:36:e1 45 No 19s
b4:b6:76:42:36:b4 46 No 29s
3c:a9:f4:1d:b7:94 13 No 14m:0s
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap client-probe-report | 237
00:21:6a:ba:b7:ce
04:0c:ce:e1:98:78
00:1e:65:71:18:de
60:67:20:4d:e8:a8
b4:b6:76:42:49:56
b4:b6:76:42:49:1f
c4:85:08:d4:79:48
b4:b6:76:42:49:4c
b4:b6:76:42:49:6a
c8:f7:33:a3:69:2f
c8:f7:33:a0:a9:6f
b4:b6:76:42:49:47
00:0b:6b:b1:79:f5
58:94:6b:36:5a:58
c8:f7:33:a4:9a:39
c8:f7:33:a4:5a:dd
c8:f7:33:a4:5a:2e
c8:f7:33:a4:5a:c9
b4:b6:76:42:5a:9f
7c:d1:c3:8a:6b:be
00:26:c6:52:6b:14
58:94:6b:36:cb:e8
c4:85:08:db:db:e8
b4:b6:76:42:5b:3f
b4:b6:76:42:5b:44
ac:81:12:59:5c:12
00:1e:e5:e4:ec:d0
3c:a9:f4:1d:ac:a4
00:03:7f:40:0c:13
c0:cb:38:44:fd:1d
00:19:7e:76:8d:84
00:19:77:79:ad:e0
b4:b6:76:42:6d:05
b4:b6:76:42:6d:0a
84:85:06:b3:6d:28
b4:b6:76:41:fe:a6
00:15:00:5c:de:00
88:53:2e:2c:ee:6c
10:40:f3:e4:5f:62
00:19:7e:75:ff:35
00:26:c6:bd:4f:10
Total 74 Stations
31 No 2s
50 No 8h:3m:27s
8 No 53m:14s
13 No 2h:8m:22s
41 No 14s
34 No 25s
33 No 29s
48 No 31s
42 No 33s
33 No 34s
35 No 41s
37 No 41s
33 No 0s
41 No 9h:27m:23s
33 No 2m:29s
46 No 3s
42 No 2s
40 No 12s
37 No 18s
56 No 51m:33s
43 No 5h:23m:36s
45 No 10h:3m:19s
40 No 20s
38 No 28s
46 No 47s
54 No 3h:58m:3s
35 No 1h:58m:59s
40 No 10h:27m:17s
19 No 30s
34 No 1h:40m:9s
13 No 8m:23s
52 No 43s
40 No 7s
36 No 28s
16 No 1m:25s
45 No 7s
14 No 53s
24 No 10s
56 No 8h:50m:12s
26 No 26m:50s
28 No 51s
Command History
Version
Description
Dell Networking W-Series Instant
6.3.1.1-4.0
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
238 | show ap client-probe-report
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap client-match-refused
show ap client-match-refused [<radio>]
Description
This command displays the list of clients for which the channel allocation is refused based on the client match
configuration parameters.
Syntax
Parameter
Description
<radio>
Allows you to filter the output based the ID number of the radio (for example, 0 or
1).
Usage Guidelines
Use this command to view the list of clients for which client match actions are refused. When the client match
feature is enabled on a W-IAP, the W-IAP measures the RF health of its associated clients. If spectrum load
balancing is triggered and a client's Received Signal Strength Indication (RSSI) is or less than 20 dB, clients are
moved from one AP to another for better performance and client experience.
Example
The following example shows the output of the show ap client-match-refused command.
Client Match Status:: RUNNING BALANCING
Associated:1, Threshold:1
Leaving:0, Coming:0
Last Refused Clients Table
-------------------------MAC RSSI Refused Count Last Refused Time
--- ---- ------------- ----------------02:99:00:00:01:33 27 2 3
7e:17:7b:2c:f5:e2 5 4 6
00:27:10:c5:96:54 22 1 0
18:3d:a2:0a:48:3c 33 2 1
02:21:00:00:00:14 28 2 5
00:27:10:cf:ef:b4 32 2 7
7e:17:7b:27:6b:af 6 2 3
00:db:df:0a:6a:db 21 2 4
00:24:6c:c8:74:4c# show ap client-match-ref 1
Client Match Status:: RUNNING
Associated:0, Threshold:1
Leaving:0, Coming:0
Last Refused Clients Table
-------------------------MAC RSSI Refused Count Last Refused Time
--- ---- ------------- ----------------02:99:00:00:01:33 35 2 3
00:db:df:0a:6a:db 29 3 10
fc:75:16:03:40:d9 41 10 3
18:3d:a2:09:79:ac 27 2 11
00:db:df:05:1f:d6 37 2 6
02:21:00:00:00:14 23 3 3
00:27:10:cf:ef:b4 27 2 5
00:27:10:cf:f2:4c 18 1 6
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap client-match-refused | 239
Command History
Version
Description
Dell Networking W-Series Instant
6.3.1.1-4.0
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
240 | show ap client-match-refused
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap client-match-triggers
show ap client-match-triggers
Description
This command displays the configuration conditions that trigger client match events and actions for the clients
associated with a W-IAP.
Usage Guidelines
Use this command to view the clients match trigger records. When the client match feature is enabled on a IAP, the
W-IAP measures the RF health of its associated clients. Based on the following trigger conditions, the clients are
moved from one AP to another for better performance and client experience.
l
Dynamic Load Balancing:
l
Sticky Clients
l
Band Steering
l
Channel Utilization
l
Client Capability Match
For more information on client match and client match trigger conditions, see Dell Networking W-Series Instant
6.4.0.2-4.1 User Guide.
Example
The following example shows the output of the show ap client-match-triggers command:
Client Match Triggers
--------------------Station PHY Target_AP Reason STA_CAP rssi chan ccnt cutil g_ccnt RSSI CHAN CCNT ROOM CUTIL
------- --- --------- ------ ------- ---- ---- ---- ----- ------ ---- ---- ---- ---- ----- --A_CCNT Time
--- ---00:15:00:5e:7e:3c 0 9c:1c:12:3a:e9:70 Dynamic Load Balancing - 25 36+ 12 - - 44 44+ 2 - - 3h:11m:19s
5a:15:00:00:00:16 1 9c:1c:12:3a:e9:10 Sticky Client - 17 6 - - - 34 40- - - - - 2h:11m:40s
00:15:00:5e:77:c8 0 9c:1c:12:3a:e9:10 Dynamic Load Balancing - 36 48- 19 - - 38 40- 0 - - 2h:11m:34s
a4:4e:31:97:da:74 0 9c:1c:12:3a:e9:10 Dynamic Load Balancing - 31 48- 19 - - 42 40- 0 - - 2h:11m:34s
00:15:00:5b:72:1c 1 9c:1c:12:3a:e9:60 Sticky Client - 24 5 - - - 35 6 - - - - 1h:29m:37s
5a:12:00:00:00:11 0 9c:1c:12:3a:e6:70 Dynamic Load Balancing - 15 44+ 9 - - 35 40- 9 - - 1h:9m:41s
Total 6 Records
The output of this command displays client match trigger records with details such as station MAC, target AP MAC,
trigger condition and so on.
Command History
Version
Description
Dell Networking W-Series Instant
6.4.0.2-4.1
This command is introduced.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap client-match-triggers | 241
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
242 | show ap client-match-triggers
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap client-view
show ap client-view
Description
This command displays information about the clients in the AP neighborhood.
Usage Guidelines
Use this command to view information about the clients associated with the neighboring W-IAPs.
Example
The following example shows the output of show ap client-view command:
Client Match Neighbor Table
--------------------------MAC Channel RSSI Clients Threshold Channel Util (%) VC Key Flags Received
--- ------- ---- ------- --------- ---------------- ------ ----- -------d8:c7:c8:44:50:c0 6 13 1 - - - 8m:27s
d8:c7:c8:44:50:d0 40 8 2 - - - V 1s
d8:c7:c8:44:51:b0 44 40 10 - - - VR 2m:49s
d8:c7:c8:44:61:a0 1 36 3 - - - VR 58s
d8:c7:c8:44:61:b0 48 24 3 - - - V 1s
d8:c7:c8:44:51:a0 11 50 4 - - - VR 1s
d8:c7:c8:44:62:a0 6 19 2 - - - V 20s
6c:f3:7f:ef:12:c0 1 28 0 1 0 271d9383 VRIC 4s
6c:f3:7f:ef:12:d0 149E 72 0 1 0 271d9383 VRIC 13s
d8:c7:c8:44:62:b0 149 3 3 - - - 9m:8s
6c:f3:7f:ef:03:00 6 24 0 0 0 847face0 B 5m:7s
d8:c7:c8:44:63:90 153 9 2 - - - V 19s
6c:f3:7f:ee:f7:80 3 76 0 1 0 271d9383 VRIC 6s
6c:f3:7f:ee:f7:90 52E 62 0 1 0 271d9383 VRIC 4s
d8:c7:c8:44:4a:30 161 7 2 - - - S 12m:43s
d8:c7:c8:44:4b:80 6 10 3 - - - VR 1m:24s
d8:c7:c8:44:4b:90 48 17 2 - - - VR 2m:34s
6c:f3:7f:ee:dc:20 11 32 2 3 0 847face0 3m:6s
d8:c7:c8:44:4c:80 6 24 1 - - - VR 2m:27s
d8:c7:c8:44:4c:90 36 20 11 - - - VR 2m:34s
6c:f3:7f:e7:5d:40 1 59 1 3 0 847face0 14m:24s
Neighbor Flags: V - Valid; R - In RF Neighborhood; S - Same Channel;
B - Balancing; C - Client Match Enabled; I - In Same Swarm
Total 21 Neighbors
00:24:6c:c8:74:4c# show ap client-match-live
Client Match Table
-----------------Station CM State RSSI Radio Home AP Target AP Time
------- -------- ---- ----- ------- --------- ---00:db:df:0a:57:4e Adopted 47 0 - - 5m:17s
Total 1 Client Matches
Command History
Version
Description
Dell Networking W-Series Instant
6.3.1.1-4.0
This command is introduced.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap client-view | 243
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
244 | show ap client-view
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug airwave
show ap debug airwave
Description
This command displays the list of W-AirWave servers configured on a W-IAP.
Usage Guidelines
Use this command to view the list of W-AirWave servers configured for a W-IAP.
Example
The following example shows the output of show ap airwave command:
Airwave Server List
------------------Domain/IP Address Type Mode Status
---------- ---- ---- -----test.com Primary - Not connected
test1.com Backup - Not connected
The output of this command includes the following information:
Column
Description
Domain/IP Address
Displays the IP address or domain name of the W-AirWave server.
Type
Displays the type of the W-AirWave server. For example, backup or primary
server.
Mode
Indicates the mode of W-AirWave operation.
NOTE: W-AirWave can be configured to operate in the Manage Read/Write or
Monitor-only+ Firmware Upgrades modes.
Status
Indicates the W-AirWave login status.
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.1-4.0
The Domain name is added.
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug airwave | 245
show ap debug airwave-config-received
show ap debug airwave-config-received
Description
This command indicates if any configuration information is received by the W-IAP from the W-AirWave server.
Usage Guidelines
Use this command to view if any configuration information is received from the W-AirWave server.
Example
The following example shows the output of the show ap debug airwave-config-received command:
show ap debug airwave-config-received
No configuration received from AirWave yet
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
246 | show ap debug airwave-config-received
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug airwave-data-sent
show ap debug airwave-data-sent
Description
This command displays information about data exchange between the W-AirWave server and the W-IAP.
Usage Guidelines
Use this command to view information about the data sent to the W-AirWave server.
Example
The following example shows the output of the show ap debug airwave-data-sent command:
cat: /tmp/awc_buf.txt: No such file or directory
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug airwave-data-sent | 247
show ap debug airwave-events-pending
show ap debug airwave-events-pending
Description
This command displays the pending W-AirWave server events.
Usage Guidelines
Use this command to view the pending W-AirWave server events.
Example
The following example shows the partial output of the show ap debug airwave-events-pending command:
<t11>
<e61>1106</e61>
<e62>654</e62>
<e1005>6c:f3:7f:56:7f:60</e1005>
<e1006>7SPOT</e1006>
<e1001>d8:c7:c8:cb:d4:20</e1001>
<e1056>2</e1056>
<e1017>d8:c7:c8:cb:d4:20</e1017>
<e1018>1</e1018>
<e1058>Varbind deprecated</e1058>
</t11>
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
248 | show ap debug airwave-events-pending
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug airwave-signon-key
show ap debug airwave-signon-key
Description
This command displays the W-AirWave sign on key used by the used by the administrator to manually authorize the
first Virtual Controller for an organization.
Usage Guidelines
Use this command to view the W-AirWave sign on key details for debugging purpose.
Example
The following example shows the output of the show ap debug airwave-signon-key command:
awc_ui_key_new : 8adf05e0013cb69393335b32627b02db7b49af0705da9fbda6
awc_ui_key_old : 9418cf5e0137b6b2d99e78c64e8604522948881d78fd7781e2
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug airwave-signon-key | 249
show ap debug airwave-state
show ap debug airwave-state
Description
This command displays the configuration details and status of W-AirWave events associated with a W-IAP.
Usage Guidelines
Use this command to view the current state of W-AirWave events associated with the W-IAP.
Example
The following example shows the output of the show ap debug airwave-state command:
<t1>
<e1>fc6520ad018ee6eb13bdc6b985e0fe6361bd37f7d25212a77e</e1>
<e2>Instant-C4:42:98</e2>
<e3></e3>
<e5>0.0.0.0</e5>
<e8>6.2.0.0-3.3.0.0_37557</e8>
<e60>Dell</e60>
<e79>c3abebcd0138eb8997a5ee52abf418883ee1356fbf0befba81</e79>
<e63></e63>
<e64></e64>
</t1>
<t4>
<e25>test</e25>
<e26>2</e26>
<e27></e27>
<e28>64</e28>
<e29>1</e29>
<e30>2</e30>
</t4>
<t4>
<e25>test123</e25>
<e26>3</e26>
<e27></e27>
<e28>64</e28>
<e29>1</e29>
<e30>2</e30>
</t4>
<t2>
<e1>d8:c7:c8:c4:42:98</e1>
<e6>BE0000315</e6>
<e2>d8:c7:c8:c4:42:98</e2>
<e7>1.3.6.1.4.1.14823.1.2.34</e7>
<e18></e18>
<e5>10.17.88.59</e5>
<e15>10</e15>
<e16>129183744</e16>
<e17>71094272</e17>
<e13>1</e13>
<e14>257137</e14>
<e65>0</e65>
<t3>
<e1>d8:c7:c8:c4:29:88</e1>
<e23>48-</e23>
<e24>22</e24>
<e10>0</e10>
<e11>1</e11>
250 | show ap debug airwave-state
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
<e47>93</e47>
<e46>3</e46>
</t3>
<t3>
<e1>d8:c7:c8:c4:29:80</e1>
<e23>1</e23>
<e24>22</e24>
<e10>1</e10>
<e11>0</e11>
<e47>80</e47>
<e46>61</e46>
</t3>
</t2>
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug airwave-state | 251
show ap debug airwave-stats
show ap debug airwave-stats
Description
This command displays the configuration statistics associated with a W-IAP managed or monitored by the WAirWave server.
Usage Guidelines
Use this command to view configuration details of a W-IAP managed or monitored by the W-AirWave server.
Example
The following example shows the partial output of the show ap debug airwave-stats command:
<t7>
<e1>d8:c7:c8:3d:3a:83</e1>
<e25>test_wep</e25>
<e23>1</e23>
<e22>1</e22>
<e21>1</e21>
<e19>2</e19>
<e20>1</e20>
</t7>
<t7>
<e1>6c:f3:7f:a5:df:32</e1>
<e25>sw-san-rapng-l3</e25>
<e23>153</e23>
<e22>1</e22>
<e21>1</e21>
<e19>1</e19>
<e20>1</e20>
</t7>
<t7>
<e1>d8:c7:c8:3d:46:d2</e1>
<e25>test_1x_term</e25>
<e23>48</e23>
<e22>1</e22>
<e21>1</e21>
<e19>1</e19>
<e20>2</e20>
</t7>
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
252 | show ap debug airwave-stats
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug am-config
show ap debug am-config
Description
This command displays the information required for debugging a W-IAP.
Syntax
Parameter
Description
mac
MAC address in the trace buffer.
Example
The following example shows the partial output of show ap debug am-config command:
Channel Number
-------------1
7
Valid 40MHz A-Channel Pairs
---------------------------Channel Number
-------------36
44
52
60
149
157
AP System Configuration
----------------------Parameter Value
--------- ----AM Scan RF Band all
RF Behavior Configuration
------------------------Parameter Value
--------- ----Station Handoff Assist Disable
RSSI Falloff Wait Time 0
Low RSSI Threshold 0
RSSI Check Frequency 0
Event Thresholds Configuration
-----------------------------Parameter Value
--------- ----Detect Frame Rate Anomalies Disable
Bandwidth Rate High Watermark 0
Bandwidth Rate Low Watermark 0
Frame Error Rate High Watermark 0
Frame Error Rate Low Watermark 0
Frame Fragmentation Rate High Watermark 0
Frame Fragmentation Rate Low Watermark 0
Frame Low Speed Rate High Watermark 0
Frame Low Speed Rate Low Watermark 0
Frame Non Unicast Rate High Watermark 0
Frame Non Unicast Rate Low Watermark 0
Frame Receive Error Rate High Watermark 0
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug am-config | 253
Frame Receive Error Rate Low Watermark 0
Frame Retry Rate High Watermark 0
Frame Retry Rate Low Watermark 0
Interference Configuration
-------------------------Parameter Value
--------- ----Detect Interference Disable
Interference Increase Threshold 0
Interference Increase Timeout 0
Interference Wait Time 0
IDS General Configuration
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
254 | show ap debug am-config
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug auth-trace-buf
show ap debug auth-trace-buf [<Mac>]
Description
This command displays the trace buffer for authentication events associated with the W-IAP.
Syntax
Parameter
Description
<Mac>
Displays the authentication trace information for a specific MAC
address.
Usage Guidelines
Use the output of this command to troubleshoot authentication errors. Include the <MAC> parameter to filter data by
the MAC address of the client to view specific details.
Example
The following example shows the output of show ap debug auth-trace-buf command:
Auth Trace Buffer
----------------May 10 13:05:09 station-up *
May 10 13:05:09 wpa2-key1 <May 10 13:06:30 station-up *
May 10 13:06:30 wpa2-key1 <May 10 13:06:30 wpa2-key2 ->
May 10 13:06:30 wpa2-key3 <May 10 13:06:30 wpa2-key4 ->
May 10 13:07:03 station-up *
May 10 13:07:03 wpa2-key1 <May 10 13:07:03 wpa2-key2 ->
May 10 13:07:03 wpa2-key3 <May 10 13:07:03 wpa2-key4 ->
ac:81:12:59:5c:12
ac:81:12:59:5c:12
08:ed:b9:e1:51:7d
08:ed:b9:e1:51:7d
08:ed:b9:e1:51:7d
08:ed:b9:e1:51:7d
08:ed:b9:e1:51:7d
08:ed:b9:e1:51:7d
08:ed:b9:e1:51:7d
08:ed:b9:e1:51:7d
08:ed:b9:e1:51:7d
08:ed:b9:e1:51:7d
d8:c7:c8:3d:42:13
d8:c7:c8:3d:42:13
d8:c7:c8:3d:42:12
d8:c7:c8:3d:42:12
d8:c7:c8:3d:42:12
d8:c7:c8:3d:42:12
d8:c7:c8:3d:42:12
d8:c7:c8:3d:42:12
d8:c7:c8:3d:42:12
d8:c7:c8:3d:42:12
d8:c7:c8:3d:42:12
d8:c7:c8:3d:42:12
-
- wpa2 psk aes
117
- wpa2 psk aes
117
117
151
95
- wpa2 psk aes
117
117
151
95
The command output displays the most recent ten trace buffer entries for the W-IAP. Each row in the output of this
table may include some or all of the following information:
l
A timestamp that indicates when the entry was created.
l
The type of exchange that was made.
l
The direction the packet was sent.
l
The source MAC address.
l
The destination MAC address.
l
The packet number.
l
The packet length.
l
Additional information such as encryption and WPA type.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug auth-trace-buf | 255
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
256 | show ap debug auth-trace-buf
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug client-match
show ap debug client-match <radio>
Description
This command displays the information about the client match configuration status on an AP radio interface.
Syntax
Parameter
Description
<radio>
Allows you to specify the ID number of the radio (for example, 0 or 1) for which you
want to view client match configuration status.
Usage Guidelines
Use this command to view the status of client match configuration for a specific radio interface.
Example
The following example shows the output of show ap debug client-match <radio ID> command:
Client Match Status:: RUNNING
Associated:0, Threshold:MAX
Leaving:0, Coming:0
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.14.0
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug client-match | 257
show ap debug client-stats
show ap debug client-stats <mac)
Description
This command displays detailed statistics about a W-IAP client.
Syntax
Parameter
Description
<mac>
Displays data based on the client MAC address.
Usage Guidelines
Use this command to view information about a W-IAP client.
Example
The following command output displays statistics for packets received from and transmitted to the specified client:
Station Stats
------------Parameter Value
--------- -------------------- General Per-radio Statistics
---------------- Transmit specific Statistics
Frames Rcvd For TX 22
Tx Frames Dropped 0
Frames Transmitted 22
Success With Retry 1
Tx Mgmt Frames 2
Tx Probe Responses 0
Tx Data Frames 20
Tx CTS Frames 0
Dropped After Retry 0
Dropped No Buffer 0
Missed ACKs 1
Long Preamble 22
Short Preamble 0
Tx EAPOL Frames 13
Tx 6 Mbps 15
Tx 48 Mbps 5
Tx 54 Mbps 2
Tx WMM [VO] 15
UAPSD OverflowDrop 0
---------------- Receive specific Statistics
Last SNR 31
Last SNR CTL0 28
Last SNR CTL1 25
Last SNR CTL2 22
Last ACK SNR 32
Last ACK SNR CTL0 30
Last ACK SNR CTL1 28
Last ACK SNR CTL2 21
Last ACK SNR EXT0 5
Last ACK SNR EXT1 4
Frames Received 2932
Rx Data Frames 2930
Null Data Frames 2879
258 | show ap debug client-stats
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Rx
PS
Rx
Rx
Rx
Rx
Rx
Rx
Rx
Rx
Mgmt Frames 1
Poll Frames 0
6 Mbps 14
12 Mbps 6
18 Mbps 5
24 Mbps 2
36 Mbps 13
48 Mbps 1162
54 Mbps 1730
WMM [BE] 39
The output of this command includes the following information:
Parameter
Description
Frames Rcvd For TX
Shows the number of frames received for transmission.
Tx Frames Dropped
Shows the number of transmission frames that were dropped.
Frames Transmitted
Shows the number of frames successfully transmitted.
Success With Retry
Shows the number of frames that were transmitted after being retried.
Tx Mgmt Frames
Shows the number of management frames transmitted.
Tx Probe Responses
Shows the number of transmitted probe responses.
Tx Data Frames
Shows the number of transmitted data frames.
Tx CTS Frames
Shows the number of clear-to-sent (CTS) frames transmitted.
Dropped After Retry
Shows the number of frames dropped after an attempted retry.
Dropped No Buffer
Shows the number of frames dropped because the AP’s buffer was full.
Missed ACKs
Shows the number of missed acknowledgements (ACKs)
Long Preamble
Shows the number of frames sent with a long preamble.
Short Preamble
Shows the number of frames sent with a short preamble.
Tx EAPOL Frames
Shows the number of Extensible Authentication Protocol over LAN (EAPOL)
frames transmitted.
Tx <n> Mbps
Shows the number of frames transmitted at <n> Mbps, where <n> is a value
between 6 and 300.
Tx WMM
Shows the number of Wi-Fi Multimedia (WMM) packets transmitted for the
following access categories. If the AP has not transmitted packets in a category
type, this data row will not be displayed in the output of the command.
Tx WMM [BE]: Best Effort
Tx WMM [BK]: Background
Tx WMM [VO]: VoIP
Tx WMM [VI]: Video
UAPSD OverflowDrop
Shows the number of packets dropped due to Unscheduled Automatic Power
Save Delivery (U-APSD) overflow.
Last SNR
Indicates the last recorded signal-to-noise ratio.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug client-stats | 259
Parameter
Description
Last SNR CTL0
Indicates the signal-to-noise ratio for the last received data packet on the primary
(control) channel 0. This parameter is only displayed for APs operating in 40 MHz
mode.
Last SNR CTL1
Indicates the signal-to-noise ratio for the last received data packet on the
secondary (control) channel 1. This parameter is only displayed for APs operating
in 40 Mhz mode.
Last SNR CTL2
Indicates the signal-to-noise ratio for the last received data packet on the
secondary (control) channel 2. This parameter is only displayed for APs operating
in 40 MHz mode.
Last ACK SNR
Indicates the signal-to-noise ratio for the last received ACK packet.
Last ACK SNR CTL0
Indicates the signal-to-noise ratio for the last received ACK packet on the primary
(control) channel 0. This parameter is only displayed for APs operating in 40 MHz
mode.
Last ACK SNR CTL1
Indicates the signal-to-noise ratio for the last received ACK packet on the primary
(control) channel 1. This parameter is only displayed for APs operating in 40 MHz
mode.
Last ACK SNR CTL2
Indicates the signal-to-noise ratio for the last received ACK packet on the primary
(control) channel 2. This parameter is only displayed for APs operating in 40 MHz
mode.
Last ACK SNR EXT0
Indicates the signal-to-noise ratio for the last received ACK packet on the
secondary (extension) channel 0. This parameter is only displayed for APs
operating in 40 MHz mode.
Last ACK SNR EXT1
Indicates the signal-to-noise ratio for the last received ACK packet on the
secondary (extension) channel 1. This parameter is only displayed for APs
operating in 40 MHz mode.
Frames Received
Shows the number of frames received.
Rx Data Frames
Shows the number of data frames received.
Null Data Frames
Shows the number of null data frames received.
Rx Mgmt Frames
Shows the number of management frames received.
PS Poll Frames
Shows the number of power save poll frames received.
Rx <n> Mbps
Shows the number of frames received at <n> Mbps, where <n> is a value between
6 and 300.
Tx WMM
Shows the number of Wi-Fi Multimedia (WMM) packets transmitted for the
following access categories. If the AP has not transmitted packets in a category
type, this data row will not be displayed in the output of the command.
Tx WMM [BE]: Best Effort
Tx WMM [BK]: Background
Tx WMM [VO]: VoIP
Tx WMM [VI]: Video
260 | show ap debug client-stats
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug client-stats | 261
show ap debug client-table
show ap debug client-table
Description
This command shows the clients associated with a W-IAP.
Usage Guidelines
Use this command to view a list of W-IAP clients.
Example
The following example shows the output of show ap debug client-table command:
Client Table
-----------MAC ESSID BSSID Assoc_State HT_State AID PS_State -------- ----- ----------- -------- --- ------08:ed:b9:e1:51:7d example1 d8:c7:c8:3d:42:12 Associated WSsM 0x1 Awake
UAPSD Tx_Pkts Rx_Pkts PS_Qlen Tx_Retries Tx_Rate Rx_Rate Last_ACK_SNR
----- ------ ------- ------- ---------- ------- ------- -----------(0,0,0,0,N/A,0) 101 12888 0 0 300 300 45
----------Last_Rx_SNR TX_Chains Tx_Timestamp Rx_Timestamp MFP Status (C,R)
--------- ------------ ---------- ---------------- ---------------50 3[0x7] Sun May 12 07:41:25 2013 Sun May 12 07:42:13 2013 (0,0)
UAPSD:(VO,VI,BK,BE,Max SP,Q Len)
HT Flags: A - LDPC Coding; W - 40Mhz; S - Short GI HT40; s - Short GI HT20
D - Delayed BA; G - Greenfield; R - Dynamic SM PS
Q - Static SM PS; N - A-MPDU disabled; B - TX STBC
b - RX STBC; M - Max A-MSDU; I - HT40 Intolerant
The output of this command includes the following information:
Parameter
Description
MAC
Indicates the MAC address of the W-IAP.
ESSID
Indicates the Extended Service Set identifier (ESSID) used by the client. An ESSID is a userdefined name for a wireless network.
BSSID
Filters the W-IAP Config table by BSSID. The Basic Service Set Identifier (BSSID) is usually
the AP’s MAC address.
Assoc_State
Shows whether or not the client is currently authorized and/or associated with the W-IAP.
HT_State
Shows the client’s high-throughput (802.11n) transmission type:
AID
262 | show ap debug client-table
l
none: AP is a legacy AP that does not support the 802.11n standard.
l
20Mhz: A high-throughput APs using a single 20 Mhz channel.
l
40Mhz: A high-throughput APs using two 20 Mhz channels.
Indicates the 802.11 association ID. A client receives a unique 802.11 association ID when
it associates to a W-IAP.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Parameter
Description
UAPSD
Shows the following values for Unscheduled Automatic Power Save Delivery (UAPSD) in
comma-separated format: VO, VI, BK, BE, Max SP, Q Len.
l
VO: If 1, UAPSD is enabled for the VoIP access category. If UAPSD is disabled for
this access category, this value is 0.
l
VI: If 1, UAPSD is enabled for the Video access category. If UAPSD is disabled for
this access category, this value is 0.
l
BK: If 1, UAPSD is enabled for the Background access category. If UAPSD is
disabled for this access category, this value is 0.
l
BE: If 1, UAPSD is enabled for the Best Effort access category. If UAPSD is
disabled for this access category, this value is 0.
l
Max SP: The maximum service period is the number of frame sent per trigger
packet. This value is value can be 0, 2, 4 or 8.
l
Q Len: The number of frames currently queued for the client, from 0 to 16 frames.
Tx_Pkts
Shows the number of packets transmitted by the client.
Rx_Pkts
Shows the number of packets received by the client.
PS_Qlen
Shows power save queue length, in bytes.
Tx_Retries
Shows the number of packets that the client had to resend due to an initial transmission
failure.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug client-table | 263
show ap debug crash-info
show ap debug crash-info
Description
This command displays log information for a W-IAP that crashed. The stored crash information is cleared from the
flash after the W-IAP reboots.
Syntax
No parameters
Usage Guidelines
Use this command to view the W-IAP crash information for debugging purpose.
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
264 | show ap debug crash-info
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug dhcp-packets
show ap debug dhcp-packets
Description
This command displays information about the DHCP packets sent or received by a W-IAP.
Usage Guidelines
Use this command to view information about the DHCP packets trace information for a W-IAP.
Example
The following example shows the output of show ap debug dhcp-packets command:
Traced Dhcp Packets
------------------Timestamp Mtype Htype Hops TID Cip Yip Sip Gip Cmac
--------- ----- ----- ---- --- --- --- --- --- ----
The output of this command includes the following parameters:
Column
Description
Timestamp
Displays the timestamp for DHCP packets.
Mtype
Indicates the message type.
Htype
Indicates the hardware address type
Hops
Shows the number of hops.
TID
Shows the transaction ID.
Cip
Indicates the client IP address.
Yip
Indicates the IP address of the W-IAP.
Sip
Indicates the source IP address from which the DHCP packets originated.
Gip
Indicates the Gateway IP address.
Cmac
Indicates the MAC address of the client.
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug dhcp-packets | 265
show ap debug dot1x-statistics
show ap debug dot1x-statistics
Description
This command displays the aggregate 802.11X debug statistics for a W-IAP.
Usage Guidelines
Use this command to view information about the 802.11x authentication.
Example
The following output is displayed for the show ap debug dot1x-statistics command:
802.1X Statistics
----------------Mac Name AP Auth-Succs Auth-Fails Auth-Tmout Re-Auths
---------- ------ ---- ---------- -------- --------- ------- ------08:ed:b9:e1:51:7d d8:c7:c8:3d:42:12 0 0 0 0
Total: 0 0 0 0
Supp-Naks UKeyRot MKeyRot ---------- -------- -------0 0 0
0 0 0
802.1x Counters
WPA2
Message-1......................3
Message-2......................2
Message-3......................2
Message-4......................2
The output of this command includes the following parameters:
Parameter
Description
Mac
Displays the MAC address of the authenticated client.
Name
Displays the name of the client device
AP
Displays the AP device details to which the client is connected.
Auth-Succs
Displays the number of times the client authenticated successfully.
Auth-Fails
Displays the number of times the client failed to authenticate.
Auth-Timeout
Displays if client authentication timeout details.
Reauths
Displays the reauthentication attempts if any.
Supp-Naks
Displays the number of supplementary NAKs.
UkeyRot
Displays the unicast key rotation details.
MkeyRot
Displays the multicast key rotation details.
802.1X counters
Displays the 802.1X authentication counters.
266 | show ap debug dot1x-statistics
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug dot1x-statistics | 267
show ap debug driver-config
show ap debug driver-config
Description
This command displays W-IAP driver configuration.
Usage Guidelines
Use this command to review configuration changes made since the W-IAP driver was last reset.
Example
The show ap debug driver-config command displays the BSSID, SSID, and radio configuration details associated
with the W-IAP driver. The following output is displayed for the show ap debug driver-config command:
Downloaded Config for WIFI 0
---------------------------Item Value
---- ----BSSID d8:c7:c8:3d:42:12
LMS IP
Master IP 0.0.0.0
Mode AP Mode
Group Key Received Yes
QBSS Probe Response Allow Access
Native VLAN ID 1
LED operating mode (11n APs only) normal
SAP MTU 1500 bytes
Heartbeat DSCP 0
High throughput enable (radio) Enabled
Channel 44+
Transmit EIRP 24 dBm
Non-Wi-Fi Interference Immunity 2
Enable CSA Disabled
CSA Count 4
Advertise 802.11d and 802.11h Capabilities Disabled
TPC Power 0 dBm
Spectrum Load Balancing Disabled
Spectrum Load Balancing Mode channel
Spectrum Load Balancing Update Interval (sec) 30 seconds
Spectrum Load Balancing Threshold (%) 2 percent
Infrastructure assisted client association management Disabled
Beacon Period 100 msec
Beacon Regulate Disabled
Advertized regulatory max EIRP 0
ARM/WIDS Override Dynamic
Reduce Cell Size (Rx Sensitivity) 0 dB
Management Frame Throttle interval 0 sec
Management Frame Throttle Limit 0
Maximum Distance 600 meters
RX Sensitivity Threshold 0 dB
RX Sensitivity Tuning Based Channel Reuse disable
Active Scan Enabled
ARM Over the Air Updates Disabled
VoIP Aware Scan Enabled
Power Save Aware Scan Disabled
Video Aware Scan Enabled
Load aware Scan Threshold 1048576 Bps
40 MHz intolerance Disabled
Honor 40 MHz intolerance Enabled
268 | show ap debug driver-config
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
CSD override Enabled
Advertise 802.11K Capability Disabled
Measurement Mode for Beacon Reports passive
Channel for Beacon Requests in 'A' band 0
Channel for Beacon Requests in 'BG' band 0
Channel for AP Channel Reports in 'A' band 0
Channel for AP Channel Reports in 'BG' band 0
Time duration between consecutive Beacon Requests 0 sec
Time duration between consecutive Link Measurement Requests 0 sec
Time duration between consecutive Transmit Stream Measurement Requests 0 sec
Enable Handover Trigger feature Disabled
Advertise Enabled Capabilities IE Disabled
Advertise Country IE Disabled
Advertise Power Constraint IE Disabled
Advertise TPC Report IE Disabled
Advertise QBSS Load IE Disabled
Advertise BSS AAC IE Disabled
Advertise Quiet IE Disabled
Advertise Fast-BSS Transition (802.11r) Capability Disabled
Fast-BSS Transition Mobility Domain ID 0
Country Code IN
ESSID example1
Encryption wpa2-psk-aes
WPA2 Pre-Auth Disabled
Enable Management Frame Protection Disabled
Require Management Frame Protection Disabled
DTIM Interval 1 beacon periods
802.11a Basic Rates 6 12 24
802.11a Transmit Rates 6 9 12 18 24 36 48 54
Station Ageout Time 1000 sec
Max Transmit Attempts 16
RTS Threshold 2333 bytes
Max Associations 64
Wireless Multimedia (WMM) Enabled
Wireless Multimedia U-APSD (WMM-UAPSD) Powersave Enabled
WMM TSPEC Min Inactivity Interval 0 msec
DSCP mapping for WMM voice AC N/A
DSCP mapping for WMM video AC N/A
DSCP mapping for WMM best-effort AC N/A
DSCP mapping for WMM background AC N/A
Hide SSID Disabled
Deny_Broadcast Probes Disabled
Local Probe Response Enabled
Local Probe Request Threshold (dB) 0
Disable Probe Retry Enabled
Maximum Transmit Failures 0
BC/MC Rate Optimization Disabled
Rate Optimization for delivering EAPOL frames Enabled
Strict Spectralink Voice Protocol (SVP) Disabled
802.11a Beacon Rate 0
Advertise QBSS Load IE Enabled
Advertise Location Info Disabled
Advertise AP Name Disabled
40 MHz channel usage Enabled
BA AMSDU Enable Disabled
Temporal Diversity Enable Enabled
High throughput enable (SSID) Enabled
Low-density Parity Check Enabled
Maximum number of spatial streams usable for STBC reception 1
Maximum number of spatial streams usable for STBC transmission 1
MPDU Aggregation Enabled
Max received A-MPDU size 65535 bytes
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug driver-config | 269
Max transmitted A-MPDU size 65535 bytes
Min MPDU start spacing 16 usec
Short guard interval in 20 MHz mode Enabled
Short guard interval in 40 MHz mode Enabled
Supported MCS set
Explicit Transmit Beamforming Disabled
Transmit Beamforming Compressed Steering Disabled
Transmit Beamforming non Compressed Steering Disabled
Transmit Beamforming delayed feedback support Disabled
Transmit Beamforming immediate feedback support Disabled
Transmit Beamforming Sounding Interval 0 sec
40 MHz channel usage Enabled
BA AMSDU Enable Disabled
Temporal Diversity Enable Enabled
High throughput enable (SSID) Enabled
Low-density Parity Check Enabled
Maximum number of spatial streams usable for STBC reception 1
Maximum number of spatial streams usable for STBC transmission 1
MPDU Aggregation Enabled
Max received A-MPDU size 65535 bytes
Max transmitted A-MPDU size 65535 bytes
Min MPDU start spacing 16 usec
Short guard interval in 20 MHz mode Enabled
Short guard interval in 40 MHz mode Enabled
Supported MCS set
Explicit Transmit Beamforming Disabled
Transmit Beamforming Compressed Steering Disabled
Transmit Beamforming non Compressed Steering Disabled
Transmit Beamforming delayed feedback support Disabled
Transmit Beamforming immediate feedback support Disabled
Transmit Beamforming Sounding Interval 0 sec
Forward mode bridge
Band Steering Enabled
Steering Mode prefer-5ghz
Dynamic Multicast Optimization (DMO) Disabled
Dynamic Multicast Optimization (DMO) Threshold 0
VAP on radio 1 : is not created and is not enabled
--------------------------------------------------
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
270 | show ap debug driver-config
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug mgmt-frames
show ap debug mgmt-frames <mac>
Description
This command displays the trace information for the 802.11 management frames.
Syntax
Parameter
Description
<mac>
Displays trace information for a W-IAP based on MAC address.
Example
The following example shows the partial output of show ap debug mgmt-frames command:
Traced 802.11 Management Frames
------------------------------Timestamp stype SA DA BSS signal Misc
--------- ----- ------- ------ ---May 9 23:09:42 deauth d8:c7:c8:c4:29:82 08:ed:b9:e1:51:87 d8:c7:c8:c4:29:82 15 May 9 23:09:42 disassoc d8:c7:c8:c4:29:82 08:ed:b9:e1:51:87 d8:c7:c8:c4:29:82 15 May 9 23:09:03assoc-respd8:c7:c8:c4:29:82 08:ed:b9:e1:51:87 d8:c7:c8:c4:29:82 15Success
May 9 22:02:40 auth d8:c7:c8:c4:29:8b c4:85:08:de:06:d4 d8:c7:c8:c4:29:8b 15Success
May 9 01:25:51 auth 08:ed:b9:e1:51:87 d8:c7:c8:c4:29:8a d8:c7:c8:c4:29:8a 60 -
The output of this command includes the following information:
Column
Description
Timestamp
Indicates timestamp for the authentication management frame.
stype
Indicates the type of the packet.
SA
Indicates the source of the packets.
DA
Indicates the destination to which the packets are intended.
BSS
Indicates the BSSID.
Signal
Indicates the signal level.
Misc
Indicates miscellaneous information such as status and other relevant details.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug mgmt-frames | 271
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
272 | show ap debug mgmt-frames
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug persistent-clients
show ap debug persistent-clients
Description
This command displays the information about the persistent W-IAP clients.
Usage Guidelines
Use this command to view information about the clients that are persistently connected to a W-IAP.
Example
The following example shows the output of show ap debug persistent-clients command:
Persistent Clients
-----------------MAC Address ESSID State Expired Update Time Expiration Time
----------- ----- ----- ------- ----------- ---------------
The output of this command includes the following information:
Column
Description
MAC Address
Shows the MAC address of the client.
ESSID
Shows the ESSID used by the client.
State
Indicates the connection status of the client
Expired
Indicates if the client session is expired.
Update Time
Indicates the update time.
Expiration Time
Indicates the time at which the client session expires.
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug persistent-clients | 273
show ap debug radio-stats
show ap debug radio-stats [<radio-ID>]
Description
This command displays the aggregate radio debug statistics of a W-IAP.
Syntax
Parameter
Description
<radio-ID>
Allows you to specify the ID number of the radio (for example, 0 or 1) for which you
want to view statistics.
Usage Guidelines
Use this command to view the radio debug statistics for a W-IAP.
Example
The output of this command displays general statistics for the radio, as well as statistics for transmitted and
received frames.
RADIO Stats
----------Parameter Value
--------- ----Tx Powersave Queue Timeouts 0
Tx Dropped After Retry 158551
Tx Dropped No Buffer 0
Tx Missed ACKs 158581
Tx Failed Beacons 1
Tx Multi-Beacon Fail 0
Tx Long Preamble 557658
Tx Short Preamble 0
Tx Beacon Interrupts 2597365
Tx Interrupts 780044
Tx FIFO Underrun 0
Tx Allocated Desc 557660
Tx Freed Desc 557660
Tx EAPOL Frames 15
TX STBC Frames 0
TX LDPC Frames 0
Tx AGGR Good 0
Tx AGGR Unaggr 0
Tx Data Priority [BE] 125
Tx Data 6 Mbps (Mon) 125
Tx Data 12 Mbps (Mon) 0
Tx Data 24 Mbps (Mon) 0
Tx Data 36 Mbps (Mon) 0
Tx Data 54 Mbps (Mon) 0
Tx Data 108 Mbps (Mon) 0
Tx Data 108 Mbps+ (Mon) 0
Tx Data Bytes 6 Mbps (Mon) 16648
Tx Data Bytes 12 Mbps (Mon) 0
Tx Data Bytes 24 Mbps (Mon) 0
Tx Data Bytes 36 Mbps (Mon) 0
Tx Data Bytes 54 Mbps (Mon) 0
274 | show ap debug radio-stats
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Tx Data Bytes 108 Mbps (Mon) 0
RADIO Stats
----------Parameter Value
--------- ----Tx Data Bytes 108 Mbps+ (Mon) 0
Tx 6 Mbps 557650
Tx WMM [BE] 125
Tx WMM [VO] 557532
Tx WMM [BE] Dropped 158561
Tx UAPSD OverflowDrop 0
TX Timeouts 36
Lost Carrier Events 8
Tx HT40 Hang Detected 0
Tx HT40 Hang Stuck 0
Tx HT40 Hang Possible 0
Tx HT40 Dfs IMM WAR 0
Tx HT40 Dfs HT20 WAR 0
Tx MAC/BB Hang Stuck 0
Tx Mgmt Bytes 1434583125
Tx Beacons Bytes 1202571538
------------------- Receive Specific Statistics
Rx Last SNR 16
Rx Last SNR CTL0 14
Rx Last SNR CTL1 13
Rx Last ACK SNR 0
Rx Frames Received 5622989
Rx Good Frames 4517471
Rx Bad Frames 1105518
Rx Total Data Frames Recvd 518806
Rx Total Mgmt Frames Recvd 3261635
Rx Total Control Frames Recvd 736829
Rx Total Bytes Recvd 755424522
Rx Total Data Bytes Recvd 78179450
Rx Total RTS Frames Recvd 230212
Rx Total CTS Frames Recvd 204854
Rx Total ACK Frames 2344801
The output of this command provides the following information:
Column
Description
Parameter
Displays the transmission and reception parameters.
Value
Displays the values associated with the transmission and reception
parameters.
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug radio-stats | 275
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
276 | show ap debug radio-stats
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug radius-statistics
show ap debug radius-statistics
Description
This command displays the RADIUS statistics for the authentication servers configured on a W-IAP.
Usage Guidelines
Use this command to view the authentication server details.
Example
The output of this command displays general statistics of the authentication servers configured on a W-IAP.
RADIUS Statistics
----------------Statistics TerminationServer InternalServer testserver test1234
---------- ----------------- -------------- ---------- -------In Service: Management Auth Not used Not used Not used Not used
In Service: Example1 Not used Up 67920s Not used Not used
Accounting Requests 0 0 0 0
Raw Requests 0 0 0 0
PAP Requests 0 0 0 0
CHAP Requests 0 0 0 0
MS-CHAP Requests 0 0 0 0
MS-CHAPv2 Requests 0 0 0 0
Mismatch Response 0 0 0 0
Invalid Secret 0 0 0 0
Access-Accept 0 0 0 0
Access-Reject 0 0 0 0
Accounting-Response 0 0 0 0
Access-Challenge 0 0 0 0
Unknown Response code 0 0 0 0
Timeouts 0 0 0 0
AvgRespTime (ms) 0 0 0 0
Total Qequests 0 0 0 0
Total Response 0 0 0 0
Read Error 0 0 0 0
SEQ first/last/free 0/0/0 0/0/0 0/0/0 0/0/0
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.4
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug radius-statistics | 277
show ap debug shaping-table
show ap debug shaping-table
Description
This command displays the shaping information for clients associated to a W-IAP.
Usage Guidelines
Use this command to view the shaping information for clients connected to a W-IAP.
Example
The following output is displayed for the show ap debug shaping-table command:
Interface :wifi1
VAP aruba102
in out drop fail q cmn[C:O:H] Numcl TotCl BWmgmt
28 28 0 0 0 328787-328787-328787 0-0-0 0 1 -0
d1 d2 d3 d4 d5 d6 d7 d8 d9
0 28 0 28 0 28 0 0 0
idx tokens last-t bw-t in out drop fail q tx-t rx-t al-t rate
idx d1 d2 d3 d4 d5 d6 d7 d8 d9 d10
0 2147483647 0 0 0 0 0 0 0 0 0
VAP aruba103
in out drop fail q cmn[C:O:H] Numcl TotCl BWmgmt
0 0 0 0 0 328787-328787-328787 0-0-0 0 1 -0
d1 d2 d3 d4 d5 d6 d7 d8 d9
0 0 0 0 0 0 0 0 0
idx tokens last-t bw-t in out drop fail q tx-t rx-t al-t rate
idx d1 d2 d3 d4 d5 d6 d7 d8 d9 d10
0 2147483647 0 0 0 0 0 0 0 0 0
The output of this command provides the following information:
Column
Description
in
Shows the number of packets received by the AP.
out
Shows the number of packets sent by the AP.
drop
Shows the number of packets dropped by the AP.
fail
Shows the number of packets failed.
Numcl
Shows the number of CCK (802.11b) and OFDM (802.11a/g) packets dropped.
TotCl
Shows the total number of clients associated with the AP
Bwmgmt
Displays 1 if the bandwidth management feature has been enabled. Otherwise, it
displays a 0.
idx
Shows the association index value.
tokens
Represents the credits the station has to transmit tokens.
278 | show ap debug shaping-table
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Column
Description
last-t
Shows the number of tokens that were allocated to the station last time token
allocation algorithm ran.
in
Shows the number of packets received.
out
Shows the number of packets sent.
drop
Shows the number of dropped packets.
q
Shows the number of queued packets
tx-t
Shows the total time spent transmitting data.
rx-t
Shows the total time spent receiving data.
al-t
Shows the total time allocated for transmitting data to this station.
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug shaping-table | 279
show ap debug spanning-tree
show ap debug spanning-tree
Description
This command displays the Spanning Tree Protocol (STP) information for a W-IAP.
Usage Guidelines
Use this command to view STP details on a W-IAP. STP is enabled for a wired port profile to ensure that there are no
loops in any bridged Ethernet network. STP operates on all downlink ports, regardless of forwarding mode. STP will
not operate on the uplink port and is supported only on W-IAPs with three or more ports.
Example
The following example shows the output displayed for the show ap debug spanning-tree command when there are
no STP devices found:
stpdev: can't get info No such device
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.14.0
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
280 | show ap debug spanning-tree
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug stm-config
show ap debug stm-config
Description
This command displays the W-IAP station management configuration information.
Usage Guidelines
Use this command to view the details of station management configuration.
Example
The following output is displayed for the show ap debug stm-config command:
SSID:
Server Load Balancing:disable
MAC Authentication:disable
RADIUS Accounting:disable
SSID:__wired__eth1
Server Load Balancing:disable
MAC Authentication:disable
RADIUS Accounting:disable
SSID:wireless-local-nw
Server Load Balancing:disable
MAC Authentication:disable
RADIUS Accounting:disable
Associated RADIUS Server:InternalServer
The output of this command provides the following information for each SSID:
Column
Description
SSID
Indicates the name of the SSID.
Server Load Balancing
Indicates if server load balancing is enabled.
MAC Authentication
Indicates if MAC authentication is enabled.
RADIUS Accounting
Indicates if RADIUS accounting is enabled.
Associated RADIUS
Server
Displays the authentication server details configured for an SSID.
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap debug stm-config | 281
show ap debug system-status
show ap debug system-status
Description
This command displays the detailed system configuration information for a W-IAP.
Usage Guidelines
Use this command under the guidance of Dell technical support to troubleshoot network issues. The output of this
command displays the following types of information if any for the selected W-IAP:
l
Bootstrap information
l
Per-radio statistics
l
Ethernet duplex/speed settings
l
Descriptor Usage
l
Encryption statistics
l
Tunnel heartbeat stats
l
Interface counters
l
AP uptime
l
Boot version
l
MTU discovery
l
memory usage
l
LMS information
l
ARP cache
l
Kernel slab statistics
l
Power status
l
Route table
l
Interrupts
l
CPU type
l
Interface Information
l
Crash Information
l
CPU usage statistics
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
282 | show ap debug system-status
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap dot11k-beacon-report
show ap dot11k-beacon-report <mac>
Description
This command displays the beacon report details for the 802.11k clients of a W-IAP.
Syntax
Parameter
Description
<mac>
Allows you to specify the MAC address of the client for which you want to view the
beacon report details.
Usage Guidelines
Use this command to view the beacon report details for 802.11k clients connected to a W-IAP.
Example
The following example shows the output of the show ap dot11k-beacon-report <mac> command:
(Instant AP)# show ap dot11k-beacon-report 70:11:24:56:02:72
Client: 70:11:24:56:02:72
Status: Success
Nbr count: 4
Last received: 31s
Client 11k Beacon Report
-----------------------BSSID
----6c:f3:7f:b6:62:f0
6c:f3:7f:b6:69:30
6c:f3:7f:4a:43:d0
6c:f3:7f:b6:66:30
Channel
-----38
38
46
46
RSSI
------92
94
94
92
Antenna
------0
0
0
0
The output of this command displays information on the number of 802.11k neighbors, connection status, and the
channel, RSSI and antenna details for the specified MAC address.
Command History
Version
Description
Dell Networking W-Series Instant 6.4.0.24.1
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap dot11k-beacon-report | 283
show ap dot11k-nbrs
show ap dot11k-nbrs
Description
This command displays the neighboring details of the 802.11k clients connected to a W-IAP.
Usage Guidelines
Use this command to view neighbors of the 802.11k clients connected to a W-IAP.
Example
The following example shows the output of the show ap dot11k-nbrs command:
Radio: 0
Nbr count: 3
11k Neighbours
-------------BSSID
----6c:f3:7f:b6:62:f0
6c:f3:7f:b6:69:30
6c:f3:7f:b6:66:30
Radio: 1
Nbr count: 3
11k Neighbours
-------------BSSID
----6c:f3:7f:b6:62:e0
6c:f3:7f:b6:66:20
6c:f3:7f:b6:69:20
Channel
-----292
816
808
Last Update
------1s
6s
5s
Channel
-----1
6
6
Last Update
----------13s
33s
33s
The output of this command displays information on the number of 802.11k neighbors on each radio of the W-IAP.
Command History
Version
Description
Dell Networking W-Series Instant 6.4.0.24.1
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
284 | show ap dot11k-nbrs
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap flash-config
show ap flash-config
Description
This command shows the statistics of the W-IAP configuration stored in flash memory.
Usage Guidelines
Use this command to view the configuration details in the flash memory.
Example
The following example shows the output of show ap flash-config command:
IP Address: 10.15.20.252
Network Mask:10.15.22.257
Gateway IP:10.15.20.255
DNS Server: 92.168.1.10
Domain Name: floor1.test.com
Name:Undefined
The output of this command includes the following information:
Parameter
Description
IP Address
Displays the IP address of the W-IAP.
Network Mask
Displays the Network mask of the network.
Gateway IP
Displays the Gateway IP address to which traffic is sent.
DNS Server
Displays the IP address of the DNS server.
Domain Name
Displays the Domain name of the server
Name
Displays the name of the W-IAP.
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap flash-config | 285
show ap mesh counters
show ap mesh counter
Description
This command displays the mesh counters for a W-IAP.
Usage Guidelines
Use this command to view a list of mesh counters available for a W-IAP.
Example
The following example shows the output of show ap mesh counter command.
Mesh Packet Counters
-------------------Interface Echo Sent Echo Recv Probe Req Probe Resp Assoc Req Assoc Resp Assoc Fail Link
up/down Resel. Switch Other Mgmt
--------- --------- --------- --------- ---------- --------- ---------- ---------- ----------- ------ ------ ---------Parent 0 0 770 770(770 HT) 0 0 0 0 - - 0
Received Packet Statistics: Total 7013859, Mgmt 7013859 (dropped non-mesh 0), Da ta 0 (dropped
unassociated 0)HT: pns=770 ans=0 pnr=0 ars=0 arr=0 anr=0
Recovery Profile Usage Counters
------------------------------Item Value
---- ----Enter recovery mode 0
Exit recovery mode 0
Total connections to switch 0
Mesh loop-prevention Sequence No.:370765
Mesh timer ticks:370764
d8:c7:c8:c4:42:98# show ap mesh counters
Mesh Packet Counters
-------------------Interface Echo Sent Echo Recv Probe Req Probe Resp Assoc Req Assoc Resp Assoc Fail Link
up/down Resel. Switch Other Mgmt
--------- --------- --------- --------- ---------- --------- ---------- ---------- ----------- ------ ------ ---------Parent 0 0 770 770(770 HT) 0 0 0 0 - - 0
Received Packet Statistics: Total 7016747, Mgmt 7016747 (dropped non-mesh 0), Data 0 (dropped
unassociated 0)HT: pns=770 ans=0 pnr=0 ars=0 arr=0 anr=0
Recovery Profile Usage Counters
------------------------------Item Value
---- ----Enter recovery mode 0
Exit recovery mode 0
Total connections to switch 0
Mesh loop-prevention Sequence No.:370891
Mesh timer ticks:370890
Column
Description
Interface
Indicates whether the mesh interface connects to a Parent AP or a Child AP.
Each row of data in the Mesh Packet Counters table shows counter values for
an individual interface.
286 | show ap mesh counters
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Column
Description
Echo Sent
Number of echo packets sent.
Echo Recv
Number of echo packets received.
Probe Req
Number of probe request packets sent from the interface specified in the MeshIF parameter.
Probe Resp
Number of probe response packets sent to the interface specified in the
Interface parameter.
Assoc Req
Number of association request packets from the interface specified in the
Interface parameter.
Assoc Resp
Number of association response packets from the interface specified in the
Interface parameter. This number includes valid responses and fail responses.
Assoc Fail
Number of fail responses received from the interface specified in the Interface
parameter.
Link up/down
Number of times the link up or link down state has changed.
Resel.
Number of times a mesh point attempted to reselect a different mesh portal.
Switch
Number of times a mesh point successfully switched to a different mesh portal.
Other Mgmt
Management frames of any type other than association and probe frames,
either received on child interface, or sent on parent interface.
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap mesh counters | 287
show ap mesh link
show ap mesh link
Description
This command shows the mesh link of the W-IAP.
Example
The following example shows the output of show ap mesh link command:
(Instant AP)# show ap mesh link
Neighbor list
------------MAC Portal Channel Age Hops Cost Relation Flags RSSI
Rate Tx/Rx
--- ------ ------- --- ---- ---- -------- ----- ---- ---------00:0b:86:e8:09:d1 00:1a:1e:88:01:f0 157 0 1 11.00 C 3h:15m:42s 54/54
00:1a:1e:88:02:91 00:1a:1e:88:01:f0 157 0 1 4.00 C 3h:35m:30s HL
300/300
00:0b:86:9b:27:78 Yes 157 0 0 12.00 N 3h:22m:46s - 26 00:0b:86:e8:09:d0 00:1a:1e:88:01:f0 157 0 1 11.00 N 3h:15m:36s 00:1a:1e:88:02:90 00:1a:1e:88:01:f0 157+ 0 1 2.00 N 3h:35m:6s HL
A-Req A-Resp A-Fail HT-Details Cluster ID
----- ------ ------ ---------- ---------1 1 0 Unsupported sw-ad-GB32
1 1 0 HT-40MHzsgi-2ss sw-ad-GB322
0 0 0 Unsupported mc1
0 0 0 Unsupported sw-ad-GB32
0 0 0 HT-40MHzsgi-2ss sw-ad-GB32
Total count: 5, Children: 2
65
59
65 59 -
The output of this command includes the following information:
Parameter
Description
MAC
MAC address of the mesh node.
Portal
By default, this column displays the BSSID of the mesh point. If you include the
optional names parameter, this column will display AP names, if available. The
AP names will include [p] (parent), or [c] (child) suffixes to indicate the role of the
mesh BSSID.
Channel
Number of a radio channel used by the AP.
Age
Number of seconds elapsed since the AP heard from the neighbor.
Hops
Indicates the number of hops it takes traffic from the mesh node to get to the mesh
portal. The mesh portal advertises a hop count of 0, while all other mesh nodes
advertise a cumulative count based on the parent mesh node.
Cost
A relative measure of the quality of the path from the AP to the controller. A lower
number indicates a better quality path, where a higher number indicates a less
favorable path (For example, a path which may be longer or more congested
than a path with a lower value.) For a mesh point, the path cost is the sum of the
(parent path cost) + (the parent node cost) + (the link cost).
Relation
Shows the relationship between the specified AP and the AP on the neighbor list
288 | show ap mesh link
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Parameter
Description
and the amount of time that relationship has existed.
l
l
l
l
P = Parent
C = Child
N = Neighbor
B = Blacklisted-neighbor
Flags
This parameter shows additional information about the mesh neighbor. The key
describing each flag is displayed at the bottom of the neighbor list.
RSSI
The Receive Signal Strength Indicator (RSSI) value displayed in the output of this
command represents signal strength as a signal to noise ratio. For example, a
value of 30 would indicate that the power of the received signal is 30 dBm above
the signal noise threshold.
Rate Tx/Rx
The rate, in Mbps, that a neighbor transmits data to or receives data from the
mesh-node specified by the command.
A-Req
Number of association requests from clients.
A-Resp
Number of association responses from the mesh node.
A-Fail
Number of association failures.
Cluster ID
Name of the Mesh cluster that includes the specified AP or BSSID.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap mesh link | 289
show ap mesh neighbors
show ap mesh neighbors
Description
This command shows all mesh neighbors for an AP.
Example
The following example shows the output of show ap mesh neighbors command:
Neighbor list
------------MAC Portal Channel Age Hops Cost Relation Flags RSSI Rate Tx/Rx A-Req A-Resp A-Fail HT-Details
Cluster ID
--- ------ ------- --- ---- ---- -------- ----- ---- ---------- ----- ------ ------ ------------------6c:f3:7f:a5:df:90 Yes 157 23 0 5.00 N 23s HLK 33 - 0 0 0 HT-20MHzsgi-3ss
78042e34005c8b372de0472df0727ef
6c:f3:7f:a5:df:30 Yes 153 0 0 5.00 N 3d:18h:16m:4s HLK 13 - 0 0 0 HT-20MHzsgi-3ss
b8e356bcb60d4ce984d9a7077a43936
d8:c7:c8:3d:3b:10 Yes 161 15 0 5.00 N 15s HLK 50 - 0 0 0 HT-20MHzsgi-3ss
78042e34005c8b372de0472df0727ef
Total count: 3, Children: 0
Relation: P = Parent; C = Child; N = Neighbor; B = Blacklisted-neighbor
Flags: R = Recovery-mode; S = Sub-threshold link; D = Reselection backoff; F = Auth-failure; H
= High Throughput; L = Legacy allowed
K = Connected; U = Upgrading; G = Descendant-upgrading; Z = Config pending; Y = Assocresp/Auth pending
a = SAE Accepted; b = SAE Blacklisted-neighbour; e = SAE Enabled; u = portal-unreachable; o =
opensystem
The output of this command includes the following information:
Parameter
Description
MAC
MAC address of the mesh node.
Portal
By default, this column displays the BSSID of the mesh point. If you include the
optional names parameter, this column will display AP names, if available. The AP
names will include [p] (parent), or [c] (child) suffixes to indicate the role of the
mesh BSSID.
Channel
Number of a radio channel used by the AP.
Age
Number of seconds elapsed since the AP heard from the neighbor.
Hops
Indicates the number of hops it takes traffic from the mesh node to get to the mesh
portal. The mesh portal advertises a hop count of 0, while all other mesh nodes
advertise a cumulative count based on the parent mesh node.
Cost
A relative measure of the quality of the path from the AP to the Virtual Controller. A
lower number indicates a better quality path, where a higher number indicates a
less favorable path (e.g, a path which may be longer or more congested than a
path with a lower value.) For a mesh point, the path cost is the sum of the (parent
path cost) + (the parent node cost) + (the link cost).
Relation
Shows the relationship between the specified AP and the AP on the neighbor list
and the amount of time that relationship has existed.
290 | show ap mesh neighbors
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Parameter
Description
l
l
l
l
P = Parent
C = Child
N = Neighbor
B = Blacklisted-neighbor
Flags
This parameter shows additional information about the mesh neighbor. The key
describing each flag is displayed at the bottom of the neighbor list.
RSSI
The Receive Signal Strength Indicator (RSSI) value displayed in the output of this
command represents signal strength as a signal to noise ratio. For example, a
value of 30 would indicate that the power of the received signal is 30 dBm above
the signal noise threshold.
Rate Tx/Rx
The rate, in Mbps, that a neighbor transmits data to or receives data from the
mesh-node specified by the command.
A-Req
Number of association requests from clients.
A-Resp
Number of association responses from the mesh node.
A-Fail
Number of association failures.
Cluster ID
Name of the Mesh cluster that includes the specified AP or BSSID.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap mesh neighbors | 291
show ap monitor
show ap monitor {active-laser-beams|ap-list|ap-wired-mac <mac>|arp-cache| containment-info |
enet-wired-mac <mac> | ids-state <type> | pot-ap-list | pot-sta-list | routers | scan-info |
sta-list | state <mac> | stats <mac> | status}
Description
This command shows information for W-IAP Air Monitors.
Syntax
Parameter
Description
active-laser-beams
Shows active laser beam generators. The output of this command shows a list of
all APs that are actively performing policy enforcement containment such as rogue
containment. This command can tell us which AP is sending out deauthorization
frames, although it does not specify which AP is being contained.
ap-list
Shows list of APs being monitored.
ap-wired-mac
Shows the MAC address of the wired W-IAP.
arp-cache
Shows ARP Cache of learned IP to MAC binding
containment-info
Shows containment events and counters triggered by the wired containment and
wireless containment features configured in the ids. The output of this command
shows device and target data for wired containment activity, as well as data for the
following counters. Wireless Containment Counters:
l
l
l
l
l
l
l
l
l
l
l
l
l
Last Deauth Timer Tick
Deauth frames to AP
Deauth frames to Client
Last Tarpit Timer Tick
Tarpit Frames: Probe Response
Tarpit Frames: Association Response
Tarpit Frames: Authentication
Tarpit Frames: Data from AP
Tarpit Frames: Data from Client
Last Enhanced Adhoc Containment Timer Tick
Enhanced Adhoc Containment: Frames To Data Sender
Enhanced Adhoc Containment: Frames To Data Receiver
Enhanced Adhoc Containment: Response to Request
Enhanced Adhoc Containment: Replay Response Wired Containment Counters:
l
l
l
l
Last Wired Containment Timer Tick
Last Tagged Wired Containment Timer Tick
Spoof frames sent
Spoof frames sent on tagged VLAN
enet-wired-mac
Shows Wired MAC Addresses learned.
ids-state <type>
Shows IDS State.
pot-ap-list
Display the Potential AP table. The Potential AP table shows the following data:
l
l
l
292 | show ap monitor
bssid: the AP’s Basic Service Set Identifier.
channel: The AP’s current radio channel
phy type: The radio’s PHY type. Possible values are 802.11a, 802.11a-HT-40,
802.11b/g, 802.11b/g-HT-20.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Parameter
Description
l
l
l
l
l
l
l
num-beacons: Number of beacons seen during a 10-second scan
tot-beacons: Total number of beacons seen since the last reset.
num-frames: Total number of frames seen since the last rest.
mt: Monitor time; the number of timer ticks elapsed since the first AP is
recognized.
at: Active time, in timer ticks.
ibss: Shows if ad-hoc BSS is enabled or disabled. It will be enabled if the bssid
has detected an ad-hoc BSS (an ibss bit in an 802.11 frame).
rssi: The Receive Signal Strength Indicator (RSSI) value displayed in the
output of this command represents signal strength as a signal to noise ratio.
For example, a value of 30 would indicate that the power of the received signal is
30 dBm above the signal noise threshold.
pot-sta-list
Shows the Potential client table. The Potential Client table shows the following
values:
l
l
l
l
l
last-bssid: the Last BSSID to which the client associated.
from-bssid,
to-bssid
mt:Monitor time; the number of timer ticks elapsed since the first client is
recognized.
it: Client Idle time, expressed as a number of timer ticks.
routers
Shows Router MAC Addresses learned. The output of this command includes the
router’s MAC address, IP address and uptime.
scan-info
Shows scanned information for the W-IAP.
sta-list
Shows the configuration and status of monitor information of the W-IAP.
state
Shows the AP monitoring state.
stats
Shows the AP monitoring statistics.
status
Shows the status of the AP monitoring.
Examples
show ap monitor active-laser-beams
The following example shows the output of show ap monitor active-laser-beams command:
Active Laser Beam Sources
------------------------bssid channel rssi ap name lms ip master ip inactive time
----- ------- ---- ------- ------ --------- -------------
show ap monitor ap-list
The following example shows the output of show ap monitor ap-list command:
Monitored AP Table
-----------------bssid essid chan ap-type phy-type dos dt/mt ut/it encr nstas avg-rssi curr-rssi wmacs ibss
----- ----- ---- ------- -------- --- ----- ----- ---- ----- -------- --------- ----- ---d8:c7:c8:3d:3a:93 rahul_wep 149 interfering 80211a-HT-40 disable 3904/36 97/0 wep 0 0 20 0 no
00:24:6c:80:7d:11 NTT-SPOT 1 interfering 80211b/g disable 3897/3897 9/8 wep 0 9 11 0 no
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap monitor | 293
6c:f3:7f:b6:74:22
42 41 0 no
00:24:6c:80:7d:12
6c:f3:7f:b6:74:32
59 59 0 no
00:0b:86:51:02:28
3 no
00:0b:86:51:02:2b
0 no
00:0b:86:51:02:29
no
00:0b:86:51:02:2c
00:0b:86:51:02:2a
00:0b:86:51:02:2d
00:0b:86:51:02:2e
00:0b:86:51:02:2f
00:0b:86:51:02:20
0 no
6c:f3:7f:56:81:00
00:0b:86:51:02:21
no
00:0b:86:51:02:22
syelburgi 1 interfering 80211b/g-HT-20 disable 3817/3817 0/0 wpa2-psk-aes 0
docomo 1 interfering 80211b/g disable 3779/3779 1/0 wep 0 8 7 0 no
syelburgi 40 interfering 80211a-HT-40 disable 3729/612 34/0 wpa2-psk-aes 0
kannan-01 44 interfering 80211a disable 3613/1212 10/0 wpa2-psk-aes 0 36 33
kannan-03 44 interfering 80211a disable 3555/1154 10/0 wpa2-psk-aes 0 38 35
ssid-2 44 interfering 80211a disable 3518/1117 10/0 wpa2-psk-aes 0 37 33 0
kannan-04
kannan-02
kannan-05
kannan-06
kannan-07
kannan-01
44
44
44
44
44
11
interfering
interfering
interfering
interfering
interfering
interfering
80211a disable 3494/1093 10/0 open 0 38 35 0
80211a disable 3459/1058 10/0 open 0 38 34 0
80211a disable 3459/1058 10/0 open 0 37 34 0
80211a disable 3459/1058 10/0 open 0 37 33 0
80211a disable 3459/1058 10/0 open 0 37 34 0
80211b/g disable 3444/1160 23/0 wpa2-psk-aes
no
no
no
no
no
0 0 24
7SPOT 1 interfering 80211b/g-HT-20 disable 3308/3308 72/71 open 0 0 10 0 no
ssid-2 11 interfering 80211b/g disable 3277/764 101/0 wpa2-psk-aes 0 0 28 0
kannan-02 11 interfering 80211b/g disable 3271/958 58/0 open 0 0 27 0 no
show ap monitor ap-wired-mac <mac>
The following example shows the output of show ap monitor ap-wired-mac <mac> command:
Wired MAC Table
--------------mac age
show ap monitor arp-cache
The following example shows the output of show ap monitor arp-cache command:
br0:10.17.88.188
ARP Cache Table
mac ip vlanid age
--- -- ------ --d8:c7:c8:cb:d4:20 10.17.88.188 0 1s
d8:c7:c8:cb:d3:d4 10.17.88.186 0 1s
00:0b:86:40:1c:a0 10.17.88.129 0 1m:18s
show ap monitor containment-info
The following example shows the output of show ap monitor containment-info command:
br0:10.17.88.188
ARP Cache Table
--------------mac ip vlanid age
--- -- ------ --d8:c7:c8:cb:d4:20 10.17.88.188 0 1s
d8:c7:c8:cb:d3:d4 10.17.88.186 0 1s
00:0b:86:40:1c:a0 10.17.88.129 0 1m:18s
show ap monitor enet-wired-mac
The following example shows the output of show ap monitor enet-wired-mac command:
Wired MAC Table
--------------mac age
294 | show ap monitor
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap monitor ids-state
Use this command to view information about the Intrusion Detection System (IDS) the following detection polices:
l
Detect Block ACK DOS
l
Disconnect station attack
l
Intrusion event Type
l
Intrusion rate parameters
l
Detect Omerta attack
l
Detect Power Save DOS Attack
l
Detect Rate Anomaly
l
Sequence
l
IDS Signature— Deauthentication Broadcast and Deassociation Broadcast
l
Detect AP Spoofing
l
Valid and Protected SSIDs (from IDS Unauthorized Device Profile)
The following example shows the output of show ap monitor ids-state valid-ssid command.
System Generated (using WLAN SSID profile configuration)
--------------------------------------------------------SSID
---Valid and Protected SSIDs (from IDS Unauthorized Device Profile)
-----------------------------------------------------------------SSID
---example1
example-local-nw
a36534e02ee1f3a7edeb0c247d07c9b
show ap monitor pot-ap-list
The following example shows the output of show ap monitor pot-ap-list command.
Potential AP Table
-----------------bssid channel phy num-beacons tot-beacons num-frames mt it at ibss rssi
----- ------- --- ----------- ----------- ---------- -- -- -- ---- ---d8:c7:c8:3d:3b:13 161 80211a 0 9 0 3 352 1 disable 26
d8:c7:c8:3d:3b:03 1 80211b 0 9 0 4 363 1 disable 43
00:24:6c:81:64:a8 36 80211a 0 9 0 3 185 2 disable 17
00:24:6c:81:64:a9 36 80211a 0 9 0 1 45 1 disable 17
00:24:6c:80:7a:a2 6 80211b 0 0 0 1 1 1 disable 30
Num Potential APs:5
show ap monitor pot-sta-list
The following example shows the output of show ap monitor pot-sta-list command.
Potential Client Table
---------------------mac last-bssid from-bssid to-bssid mt it channel rssi
--- ---------- ---------- -------- -- -- ------- ---00:24:d7:40:bb:b0 00:1a:1e:17:dc:62 00:00:00:00:00:00
60:67:20:5f:e1:94 00:1a:1e:17:d4:a0 00:00:00:00:00:00
58:94:6b:a0:47:74 00:1a:1e:17:d4:a1 00:00:00:00:00:00
b0:ec:71:98:da:44 00:24:6c:80:55:b0 00:00:00:00:00:00
00:27:10:2a:c6:ac 00:1a:1e:17:d4:a1 00:00:00:00:00:00
b0:65:bd:dc:51:8a 00:24:6c:80:03:4e 00:00:00:00:00:00
74:e1:b6:15:1b:5f d8:c7:c8:3d:42:13 00:00:00:00:00:00
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
133 50 7 44
6 43 7 0
217 104 7 0
37 2 7 0
72 50 7 30
217 10 149 11
164 19 149 10
show ap monitor | 295
60:67:20:5b:33:28
00:27:10:5c:23:78
00:24:d6:9d:7c:28
58:94:6b:b3:14:a8
24:77:03:d0:0a:d8
24:77:03:7a:7f:40
24:77:03:ce:a5:fc
00:23:14:9d:ba:f0
24:77:03:cf:09:2c
24:77:03:d1:05:b0
24:77:03:7a:89:50
00:1a:1e:17:d4:a1
00:24:6c:80:fd:72
00:24:6c:80:a3:90
00:24:6c:80:03:4e
00:1a:1e:17:dc:62
6c:f3:7f:94:63:80
00:24:6c:80:4f:80
00:1a:1e:17:d4:a1
00:24:6c:80:4f:81
00:1a:1e:17:dc:62
00:24:6c:80:a3:91
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:1c:b0:eb:d7:00
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:24:6c:80:a3:9a
6 5 7 0
56 53 7 27
97 96 7 28
154 1 7 14
19 14 7 16
42 41 7 0
143 16 7 0
158 36 7 0
117 57 7 22
169 33 7 37
248 20 7 37
show ap monitor routers
The following example shows the output of show ap monitor routers command.
Wired MAC of Potential Wireless Devices
---------------------------------------mac ip age
--- -- ---
show ap monitor scan-info
The following example shows the output of show ap monitor scan-info command.
WIF Scanning State: wifi0: d8:c7:c8:3d:42:10
--------------------------------------------Parameter Value
--------- ----Probe Type m-portal
Phy Type 80211a-HT-40
Scan Mode reg-domain
Scan Channel no
Disable Scanning yes
RegDomain Scan Completed yes
DOS Channel Count 0
Current Channel 149+
Current Scan Channel 153Current Channel Index 9
Current Scan Start Milli Tick 232927000
Current Dwell Time 110
Current Scan Type active
Scan-Type-Info
--------------Info-Type Active Reg-domain All-reg-domain Rare DOS
--------- ------ ---------- -------------- ---- --Dwell Times 500 250 200 100 500
Last Scan Channel 153- 44+ 0 0 0
show ap monitor state
The following example shows the output of show ap monitor state command.
DoS State
---------tx old-tx rx old-rx last-dos-time ap-ev-time sta-ev-time last-enhanced-cm-time enhanced-cm-evtime
-- ------ -- ------ ------------- ---------- ----------- --------------------- -----------------0 0 0 0 0 0 0 0 0
show ap monitor stats
The following example shows the output of show ap monitor stats command.
296 | show ap monitor
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
(Instant AP)# show ap monitor stats d8:c7:c8:cb:d4:22
Aggregate Stats
--------------retry low-speed non-unicast recv-error frag bwidth
----- --------- ----------- ---------- ---- -----0 0 0 0 0 0
RSSI
---avg-signal low-signal high-signal count duration (sec)
---------- ---------- ----------- ----- -------------40 40 40 748 70
AP Impersonation State
---------------------beacons prev-beacons exp-beacons beacon-interval imp-time imp-active wait-time
------- ------------ ----------- --------------- -------- ---------- --------0 11 11.00 100 0 0 0
AP Non-beacon-Frames:0
AP Tarpit Fake Channel:0
Raw Stats
--------tx-pkt tx-byte rx-pkt rx-byte tx-retry-pkt rx-retry-pkt tx-frag-pkt rx-frag-pkt short-hdr-pkt
long-hdr-pkt
------ ------- ------ ------- ------------ ------------ ----------- ----------- -----------------------2662202 830665629 31438 440132 0 0 0 0 2662202 0
Frame Type Stats
---------------type mgmt-pkt mgmt-byte ctrl-pkt ctrl-byte data-pkt data-byte
---- -------- --------- -------- --------- -------- --------tx 2662202 830665629 0 0 0 0
rx 0 0 31438 440132 0 0
Dest Addr Type Stats
-------------------bcast-pkt bcast-byte mcast-pkt mcast-byte ucast-pkt ucast-byte
--------- ---------- --------- ---------- --------- ---------0 0 0 0 0 0
Frame Size Packet Stats
----------------------type 0-63 64-127 128-255 256-511 512-1023 1024+
---- ---- ------ ------- ------- -------- ----tx 0 0 0 0 0 0
rx 0 0 0 0 0 0
Frame Rate Stats
---------------type pkt-6m byte-6m pkt-9m byte-9m pkt-12m byte-12m pkt-18m byte-18m pkt-24m byte-24m pkt-36m
byte-36m pkt-48m byte-48m pkt-54m byte-54m
---- ------ ------- ------ ------- ------- -------- ------- -------- ------- -------- -------------- ------- -------- ------- -------tx 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
rx 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
HT RX Rate Stats
---------------Rate Pkts Bytes
---- ---- ----HT TX Rate Stats
----------------Rate Pkts Bytes
---- ---- ----Detailed RSSI
------------10s 2m 3m 4m 5m 6m 7m 8m 9m 10m 11m 12m 13m 14m 15m
- --- -- -- -- -- -- -- -- -- --- --- --- --- --- ---
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap monitor | 297
average 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40
high 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40
low 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40
count 110 638 638 638 638 638 649 649 638 638 429 649 638 528 649
Monitored Time:233496
Last Packet Time:233528
Uptime:233529
DoS State
---------tx old-tx rx old-rx last-dos-time ap-ev-time sta-ev-time last-enhanced-cm-time enhanced-cm-evtime
-- ------ -- ------ ------------- ---------- ----------- --------------------- -----------------0 0 0 0 0 0 0 0 0
show ap monitor status
The following example shows the output of show ap monitor status command.
AP Info
------key value
--- ----Uptime 233059
AP Name d8:c7:c8:cb:d4:20
LMS IP 0.0.0.0
Master IP 0.0.0.0
AP Type 135
Country Code 21
Wired Interface
---------------mac ip gw-ip gw-mac status pkts macs gw-macs dot1q-pkts vlans
--- -- ----- ------ ------ ---- ---- ------- ---------- ----d8:c7:c8:cb:d4:20 10.17.88.188 10.17.88.129 00:0b:86:40:1c:a0 enable 2660 4 1 0 0
WLAN Interface
--------------bssid scan monitor probe-type phy-type task channel pkts
----- ---- ------- ---------- -------- ---- ------- ---d8:c7:c8:3d:42:10 enable enable m-portal 80211a-HT-40 tuned 149+ 17332616
d8:c7:c8:3d:42:00 enable enable sap 80211b/g-HT-20 tuned 1 56090990
WLAN packet counters
--------------------Interface Packets Read Bytes Read Interrupts Buffer Overflows Max PPS Cur PPS Max PPI Cur PPI
Invalid OTA msg
--------- ------------ ---------- ---------- ---------------- ------- ------- ------- --------------------d8:c7:c8:3d:42:10(wifi0) 17332616 401055780 12288142 703 1445 216 20 3 0
d8:c7:c8:3d:42:00(wifi1) 56090990 3565742575 50110266 13315 1024 275 20 1 0
Data Structures
---------------ap sta pap psta ch msg-hash ap-l
-- --- --- ---- -- -------- ---256 288 45 136 26 2 256
Other Parameters
----------------key value
--- ----Classification enable
Wireless Containment disable
Wired Containment disable
Rogue Containment disable
System OUI Table
-----------------
298 | show ap monitor
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
oui
--RTLS Configuration and State
----------------------------Type Server IP Port Freq Active Rpt-Tags Tag-Mcast-Addr Tags-Sent Rpt-Sta Incl-Unassoc-Sta
Sta-Sent Cmpd-Msgs-Sent
---- --------- ---- ---- ------ -------- -------------- --------- ------- ---------------- ------- -------------MMS N/A N/A 30 disable 01:0c:cc:00:00:00 N/A disable N/A N/A N/A
Aeroscout N/A N/A N/A disable 00:00:00:00:00:00 N/A disable N/A N/A N/A
RTLS N/A N/A 30 disable 01:18:8e:00:00:00 N/A disable N/A N/A N/A
The outputs of the AP monitor command displays the following:
l
Active laser beam sources for the W-IAP.
l
List of APs monitored by the W-IAP.
l
ARP cache details for the W-IAP.
l
List of clients monitored by the W-IAP.
l
Containment details for the W-IAP.
l
List of potential APs for the W-IAP.
l
List of potential clients for the W-IAP.
l
Information about the potential wireless devices.
l
Scanned information for the W-IAP.
l
Configuration and status of monitor information of the W-IAP.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap monitor | 299
show ap pmkcache
show ap pmkcache
Description
This command displays the pairwise master key (PMK) cache table for clients associated with the W-IAP.
Usage Guidelines
Use this command to view PMK cache table contents for the clients associated with a W-IAP.
Example
The following example shows the output of show ap pmkcache command.
PMK Cache Table
--------------Client MAC Key OKC/11r Expiry Name Role VLAN ESSID
---------- --- ------- ------ ---- ---- ---- ----00:90:7a:0d:a0:62 1F4C17D8A70C...okc 6h:52m:18s polycom1 okc-internal 1 okc-internal
00:90:7a:0d:b2:ce F20E35DB311F...okc 7h:31m:15s polycom2 okc-internal 1 okc-internal
Column
Description
Client MAC
Indicates the MAC address of the client from the which PMK is derived.
Key
Displays the cached key for the client.
OKC/11r
Indicates if OKC or 802.11r roaming is enabled.
Expiry
Displays the PMK cache expiration details in HH:MM:SS format.
Name
Indicates the name of client.
Role
Indicates the user role assigned to the client.
VLAN
Indicates the VLAN to which the client is assigned.
ESSID
Displays the ESSID details to which the client is connected.
Command History
Version
Description
Dell Networking W-Series
Instant 6.3.1.1-4.0
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
300 | show ap pmkcache
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap virtual-beacon-report
show ap virtual-beacon-report
Description
This command displays a report with the MAC address details and RSSI information of a W-IAP.
Usage Guidelines
Use this command to view virtual beacon table of a W-IAP. The virtual beacon table with the details of clients
associated a W-IAP is broadcast by each table.
Example
The following example shows the output of show ap virtual-beacon-report command.
Virtual Beacon Table
-------------------Station CM State Triggered Succeeded Owner AP RSSI Received
------- -------- --------- --------- ----- -- ---- -------00:db:df:0a:57:4e Adopted 1 1 Yes 00:24:6c:07:44:c8 (Local 0) 47 59s
Normal No 00:24:6c:07:44:c0 (Local 1) 49 2m:2s
No 6c:f3:7f:ef:12:c0 44 18s
No 6c:f3:7f:ee:f7:80 44 11s
No 6c:f3:7f:ee:f7:90 36 13s
No 6c:f3:7f:ef:12:d0 43 13s
a0:88:b4:41:64:18 Normal 1 0 No 00:24:6c:07:44:c8 (Local 0) 34 20s
Normal No 00:24:6c:07:44:c0 (Local 1) 40 18s
No 6c:f3:7f:ef:12:c0 43 18s
No 6c:f3:7f:ee:f7:80 48 11s
No 6c:f3:7f:ee:f7:90 35 13s
Yes 6c:f3:7f:ef:12:d0 36 13s
Normal Working well
Home Current AP found a better AP for the client
Deny Current AP is not the better AP
Target Current AP is the better AP
Voice Ready to move, but client is doing voice
Refused Too many clients try to move to me
Done Current AP just deauth the client
Adopted Client has moved to me successfully
Total 2 VBRs
00:24:6c:c8:74:4c# show ap debug client-match 0
Client Match Status:: RUNNING BALANCING
Associated:1, Threshold:1
Leaving:0, Coming:0
Command History
Version
Description
Dell Networking W-Series
Instant 6.3.1.1-4.0
This command is introduced.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap virtual-beacon-report | 301
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
302 | show ap virtual-beacon-report
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap-alert
show ap-alert <count>
Description
This command displays all the alerts received for the specified APs.
Usage Guidelines
Use this command to check all the alerts received for all the APs specified.
Example
The following example shows the output of show ap-alert command.
AP Alerts
--------Timestamp Type MAC Address IP Address Description
--------- ---- ----------- ---------- -----------
The output of this command includes the following information:
Column
Description
Timestamp
Indicates the time at which the alert was received.
Type
Indicates the type of alert received for the AP.
MAC Address
Indicates the MAC address of the W-IAP clients.
IP Address
Indicates the IP address associated with the AP.
Description
Displays a brief description of the alert received.
Command History
Version
Description
Dell Networking WSeries Instant
6.4.0.2-4.1
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ap-alert | 303
show app-services
show app-services
Description
This command displays the list of application services available on a W-IAP.
Usage Guidelines
Use this command to view the list of application services available on a W-IAP.
Example
The following example shows the output of the show app-services command:
Application Service
------------------Name IP Protocol Start Port End Port
---- ----------- ---------- -------any 0 0 65535
adp 17 8200 8200
bootp 17 67 69
cfgm-tcp 6 8211 8211
cups 6 515 515
dhcp 17 67 68
dns 17 53 53
esp 50 0 65535
ftp 6 21 21
gre 47 0 65535
h323-tcp 6 1720 1720
h323-udp 17 1718 1719
http-proxy2 6 8080 8080
http-proxy3 6 8888 8888
http 6 80 80
https 6 443 443
icmp 1 0 65535
ike 17 500 500
kerberos 17 88 88
l2tp 17 1701 1701
lpd-tcp 6 631 631
lpd-udp 17 631 631
msrpc-tcp 6 135 139
msrpc-udp 17 135 139
natt 17 4500 4500
netbios-dgm 17 138 138
netbios-ns 17 137 137
noe 17 32512 32512
noe-oxo 17 5000 5000
netbios-ssn 6 139 139
nterm 6 1026 1028
ntp 17 123 123
papi 17 8211 8211
pop3 6 110 110
pptp 6 1723 1723
rtsp 6 554 554
sccp 6 2000 2000
sips 6 5061 5061
sip-tcp 6 5060 5060
sip-udp 17 5060 5060
smb-tcp 6 445 445
smb-udp 17 445 445
304 | show app-services
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
smtp 6 25 25
snmp 17 161 161
snmp-trap 17 162 162
ssh 6 22 22
svp 119 0 65535
syslog 17 514 514
telnet 6 23 23
tftp 17 69 69
vocera 17 5002 5002
The output of this command provides the following information:
Parameter
Description
Name
Indicates the list of application services available on a W-IAP.
IP Protocol
Displays the IP protocol numbers for each application service.
Start Port and End
Port
Indicates the range of port numbers on which the application services are
enabled.
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show app-services | 305
show arm-channels
show arm-channels
Description
This command displays the ARM channel details configured on a W-IAP.
Usage Guidelines
Use this command to view the channel details configured on a W-IAP.
Example
The following example shows the output of show arm-channels command:
2.4 GHz
------Channel Status
------- -----1 disable
2 disable
3 disable
4 disable
5 disable
6 disable
7 disable
8 disable
9 disable
10 disable
11 enable
12 disable
13 disable
1+ enable
2+ disable
3+ disable
4+ disable
5+ disable
6+ disable
7+ enable
5.0 GHz
------Channel Status
------- -----36 disable
40 disable
44 disable
48 disable
52 disable
56 enable
60 enable
64 enable
149 enable
153 enable
157 enable
161 enable
165 enable
36+ enable
44+ enable
52+ disable
60+ disable
149+ enable
306 | show arm-channels
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
157+ enable
The output of this command provides the following information:
Parameter
Description
Channel
Displays the list of channels available in the 2.4 GHz and 5 GHz bands.
Status
Indicates if the channels in the 2.4 GHz and 5 GHz bands are enabled or
disabled.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show arm-channels | 307
show arm config
show arm config
Description
This command displays the ARM configuration details for a W-IAP.
Usage Guidelines
Use this command to view the ARM configuration details for a W-IAP.
Example
The following example shows the output of show arm config command:
Minimum Transmit Power :18
Maximum Transmit Power :127
Band Steering Mode :prefer-5ghz
Client Aware :enable
Scanning :enable
Wide Channel Bands :5ghz
Air Time Fairness Mode :fair-access
Spectrum Load Balancing :disable
SLB NB Matching Percent :75
SLB Calculating Interval :30
SLB Threshold :2
Custom Channels :No
2.4 GHz Channels
---------------Channel Status
------- -----1 enable
2 disable
3 disable
4 disable
5 disable
6 enable
7 disable
8 disable
9 disable
10 disable
11 enable
12 disable
13 disable
1+ enable
2+ disable
3+ disable
4+ disable
5+ disable
6+ disable
7+ enable
5.0 GHz Channels
---------------Channel Status
------- -----36 enable
40 enable
44 enable
48 enable
52 enable
56 enable
308 | show arm config
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
60 enable
64 enable
149 enable
153 enable
157 enable
161 enable
165 enable
36+ enable
44+ enable
52+ disable
60+ disable
149+ enable
157+ enable
The output of this command provides the following information:
Parameter
Description
Minimum Transmit
Power
Displays the minimum transmission power configured for the ARM channels.
Maximum Transmit
Power
Displays the maximum transmission power configured for the ARM channels.
Band Steering Mode
Displays the band steering mode configuration parameters
client aware
Indicates the activation status of the Client aware feature.
Scanning
Indicates if scanning for available channels is enabled.
Wide Channel Bands
Indicates if 40MHz channel are enabled on 2.4 GHz or 5 GHz band.
Air Time Fairness
Mode
Displays configuration details for the Airtime Fairness Mode feature.
Spectrum Load
Balancing
Indicates if the Spectrum load balancing feature is enabled or disabled.
SLB NB Matching
Percent
Indicates the percentage for comparing client density of AP neighbors for
spectrum load balancing.
SLB Calculating
Interval
Indicates the frequency at which the client density on W-IAP is calculated for
spectrum load balancing.
Custom Channels
Displays custom channels if any.
Channel
Displays the list of channels available in the 2.4 GHz and 5 GHz bands.
Status
Indicates if the channels in the 2.4 GHz and 5 GHz bands are enabled or
disabled.
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show arm config | 309
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
310 | show arm config
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show arp
show arp
Description
This command displays the Address Resolution Protocol (ARP) entries for the Virtual Controller.
Usage Guidelines
Use this command to view the ARM messages sent or received by the Virtual Controller.
Example
The following example shows the output of show arp command
IP address HW type Flags HW address Mask Device
192.168.10.2 0x1 0x6 D8:C7:C8:C4:42:98 * br0
10.17.88.2 0x1 0x2 00:0B:86:40:1C:A0 * br0
The output of this command includes the following information:
Parameter
Description
IP address
Displays the IP address of the device.
HW Type
Displays the type of the device.
Flags
Displays any flags for this AP.
HW address
Displays the MAC address of the device.
Mask
Displays the network mask or the IP address range.
Device
Displays the device used to send ARP requests and replies.
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show arp | 311
show attack
show attack {config| stats}
Description
This command displays information about firewall settings configured on a W-IAP to protect the network against
wired attacks such as ARP attacks or malformed DHCP packets.
Syntax
Parameter
Description
config
Displays firewall configuration details to protect the network from wired attacks.
stats
Displays attack counters.
Usage Guidelines
Use this command to view firewall configuration details or attack counters enabled on a W-IAP to protect the
network from ARP attacks and malformed DHCP packets.
Example
The following example shows the output of show attack config command:
Current Attack
-------------Attack Status
------ -----drop-bad-arp Disabled
fix-dhcp Disabled
poison-check Enabled
The output of this command indicates if the firewall settings to block invalid ARP packets and fix malformed DHCP
packets are enabled. You can also view the status of the Poison-check parameter, which triggers an alert to notify
the user about the ARP poisoning when enabled.
The following example output for the show attack stats command shows the attack counters:
attack counters
-------------------------------------Counter Value
------- ------arp packet counter 0
drop bad arp packet counter 0
dhcp response packet counter 0
fixed bad dhcp packet counter 0
send arp attack alert counter 0
send dhcp attack alert counter 0
arp poison check counter 0
garp send check counter 1628
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
312 | show attack
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show attack | 313
show auth-survivability
show auth-survivability {cached-info| debug-log [<count>]| time-out}
Description
This command displays the authentication survivability information for a W-IAP.
Syntax
Command/Parameter
Description
cached-info
Displays authentication credentials cached by the W-IAP.
debug-log [<count>]
Displays the log details for troubleshooting. The count attribute
allows you to specify the number of logs to display.
time-out
Displays the duration configured for the cache expiry.
Usage Guidelines
Use this command to view the information cache expiry duration, cached information, and log details to debug when
the authentication survivability feature is enabled. The authentication survivability feature supports a survivable
authentication framework against the remote link failure when working with the external authentication servers.
When enabled, this feature allows the W-IAPs to authenticate the previously connected clients against the cached
credentials if the connection to the authentication server is temporarily lost.
Example
The following example shows the output of the auth-survivability cached-info command:
UserName Remaining Cache-Time(minutes)
-------- ----------------------------admin1 20
The following example shows the output of the show auth-survivability time-out command:
Auth Survivability time out :24
The output of these commands provide the following information:
Parameter
Description
UserName
Indicates the username of the client whose credentials are cached.
Remaining Cache-Time
Displays the remaining duration for cache expiry.
Auth Survivability
time out
Indicates the configured duration for cache expiry.
Command History
Version
Description
Dell Networking W-Series Instant
6.4.0.2-4.1
This command was modified.
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
314 | show auth-survivability
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show auth-survivability | 315
show backup-config
show backup-config
Description
This command displays the backup configuration information on a W-IAP,
Usage Guidelines
Use this command to view the current configuration information stored in the W-IAP flash memory.
Example
The following text provides an example for the show backup-config command output:
version 6.4.0.0-4.1.0
virtual-controller-country IN
virtual-controller-key 0cb5770401cdeb6e4363c25fdfde17d907c4b095a9be5e4258
name instant-C4:42:98
terminal-access
clock timezone none 00 00
rf-band all
allow-new-aps
allowed-ap d8:c7:c8:c4:42:98
arm
wide-bands 5ghz
80mhz-support
min-tx-power 18
max-tx-power 127
band-steering-mode prefer-5ghz
air-time-fairness-mode fair-access
client-aware
scanning
client-match
syslog-level warn ap-debug
syslog-level warn network
syslog-level warn security
syslog-level warn system
syslog-level warn user
syslog-level warn user-debug
syslog-level warn wireless
mgmt-user admin 82c496d47485380deb0a01d41345d3f1
wlan access-rule default_wired_port_profile
index 1
rule any any match any any any permit
wlan access-rule wired-instant
index 2
rule masterip 0.0.0.0 match tcp 80 80 permit
rule masterip 0.0.0.0 match tcp 4343 4343 permit
rule any any match udp 67 68 permit
rule any any match udp 53 53 permit
wlan access-rule test
index 3
rule any any match any any any deny
wlan external-captive-portal
server localhost
port 80
url "/"
auth-text "Authenticated"
auto-whitelist-disable
https
316 | show backup-config
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
blacklist-time 3600
auth-failure-blacklist-time 3600
ids classification
ids
wireless-containment none
airgroup
disable
airgroupservice airplay
disable
description AirPlay
airgroupservice airprint
disable
description AirPrint
Command History
Version
Description
Dell Networking W-Series Instant 6.4.0.24.1
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show backup-config | 317
show blacklist-client
show blacklist-client [config]
Description
This command shows the configuration details for blacklisting clients and lists the clients blacklisted by W-IAP.
Syntax
Parameter
Description
config
Displays the parameters and values configured for manual or dynamic blacklisting of
clients.
Usage Guidelines
Use this command to view information about the clients blacklisted by a W-IAP.
Example
The following output is displayed for the show blacklist-client command:
Blacklisted Clients
------------------MAC Reason Timestamp Remaining time(sec) AP name
--- ------ --------- ------------------- ------00:24:6c:ca:41:51 user-defined 14:46:18 Permanent -
The output of this command provides information on the MAC address of client that is blacklisted, the reason for
blacklisting, timestamp, the associated W-IAP name, and the duration until which the client is blacklisted.
The following output is displayed for the show blacklist-client config command:
Blacklist Time :3600
Auth Failure Blacklist Time :3600
Manually Blacklisted Clients
---------------------------MAC Time
--- ---00:24:6c:ca:41:51 14:46:18
Dynamically Blacklisted Clients
------------------------------MAC Reason Timestamp Remaining time(sec) AP name
--- ------ --------- ------------------- ------Dyn Blacklist Count :0
The output of this command provides the following information:
Parameter
Description
Blacklist Time
Indicates the duration in seconds since the blacklisting has been
triggered due to an ACL rule.
auth-survivability cache-timeout
Indicates the duration in seconds after which the clients that exceed
the maximum authentication failure threshold are blacklisted.
318 | show blacklist-client
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Parameter
Description
Manually Blacklisted clients
Displays the details of clients that are blacklisted manually.
Dynamically Blacklisted Clients
Displays the list of clients that dynamically blacklisted due to multiple
authentication rules or an ACL rule trigger.
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show blacklist-client | 319
show calea config
show calea config
Description
This command displays the details configured for CALEA server integration on a W-IAP.
Usage Guidelines
Use this command to CALEA configuration details.
Example
The following example shows the output of the show calea config command:
(Instant AP)# show calea config
calea-ip :10.0.0.5
encapsulation-type :gre
gre-type :25944
ip mtu : 150
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.4
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
320 | show calea config
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show calea statistics
show calea statistics
Description
This command displays the tunnel encapsulation statistics for a W-IAP.
Usage Guidelines
Use this command to view the GRE encapsulation statistics for the W-IAPs with CALEA server integration feature
enabled.
Example
The following example shows the output of the show calea statistics command:
(Instant AP)# show calea statistics
Rt resolve fail : 0
Dst resolve fail: 0
Alloc failure : 0
Fragged packets : 0
Jumbo packets : 263
Total Tx fail : 0
Total Tx ok : 263
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.4
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show calea statistics | 321
show captive-portal
show captive-portal
Description
This command shows the external and internal captive portal parameters configured for a network profile.
Usage Guidelines
Use this command to view information about the contents displayed on the internal and external captive portal pages
for guest users.
Example
The following output is displayed for the show captive-portal command:
:Captive Portal Configuration
Background Color:13421772
Banner Color :16750848
Decoded Texts :
Banner Text :Welcome to Guest Network
Use Policy :Please read terms and conditions before using Guest Network
Terms of Use :This network is not secure, and use is at your own risk
Internal Captive Portal Redirect URL:
Captive Portal Mode:Acknowledged
:External Captive Portal Configuration
Server:localhost
Port :80
URL :/
Authentication Text:Authenticated
External Captive Portal Redirect URL:
Server Fail Through:No
The output of this command provides the following information:
Parameter
Description
Background Color
Displays the color code configured for the internal captive portal
splash page.
Banner Color
Displays the color code configured for the banner on the internal
captive portal splash page.
Banner Text
Displays the banner text for the internal captive portal splash page.
decoded-texts
Displays decoded texts.
Terms of use
Displays the terms and conditions that the internal captive portal
user must be aware of.
Use Policy
Displays usage policy text for the internal captive portal splash page.
Captive Portal Mode
Indicates if the authentication is successful and acknowledged.
Internal
Redirect
External
Redirect
Displays the URL that the users are redirected to, after a successful
authentication.
322 | show captive-portal
Captive Portal
URL
Captive Portal
URL
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Parameter
Description
Server
Displays the external Captive port server.
URL
Displays the URL of the external captive portal splash page server.
Authentication Text
Indicates if the external captive portal user authentication is
successful.
Port
Displays the port used for communicating with the external captive
portal splash page server.
Server Fail Through
Indicates if the guest clients are allowed to access the Internet when
the external captive portal server is not available.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show captive-portal | 323
show captive-portal-domains
show captive-portal-domains
Description
This command displays the internal and external captive portal server domains.
Usage Guidelines
Use this command to view information about the internal and external captive portal domains.
Example
The following output is displayed for the show captive-portal-domains command:
Internal Captive Portal Domain:
securelogin.arubanetworks.com
External Captive Portal Domains:
localhost
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.1-4.0
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
324 | show captive-portal-domains
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show cellular
show cellular {config | status}
Description
These commands display the status and cellular configuration of the W-IAP.
Syntax
Parameter
Description
show cellular config
Displays the cellular configuration details available for the W-IAP
show cellular status
Displays the status of the cellular configuration for the W-IAP
Usage Guidelines
Use these commands to view the details of the cellular configuration and status.
Example
The following output is displayed for show cellular config command:
No Comm USB Plugged in
Cellular configuration
---------------------Type Value
---- ----4g-usb-type
usb-type
usb-dev
usb-tty
usb-init
usb-auth-type PAP
usb-user
usb-passwd
usb-dial
usb-modeswitch
modem-isp
modem-country
Supported Country list
---------------------Country list
-----------France
NZ
Israel
HK
Sweden
Spain
China
UK
norway
Germany
Croatia
Aus
Saudi-Arabia
Japan
India
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show cellular | 325
US
Canada
Supported ISP list
-----------------ISP list
-------Cincinnati Bell
Virgin
Telecom
Telenor
Vodafone/SmarTone
O2
SFR
Orange
3/HUTCH
Optus
SingTel
HKCSL/1010
Verizon
ICE
Reliance NetConnect+
Tata Indicom
Airtel-3G
Nokia CS-10
NTT
KDDI
Movistar
China Unicom
China Telecom
Vodafone
Netcom
T-Mobile
Telstra
Mobily
EMOBILE
Sprint
Cricket
Vodafone-3G
Airtel
ATT
Rogers
Bell
modem status summary:No USB modem attached
The output of this command includes the following parameters:
Parameters
Description
type
Displays the type of cellular configuration. For example, 3G or 4G modems.
value
Displays the values associated with the cellular configuration parameters.
Supported Country list
Lists the countries that support cellular deployment.
ISP List
Lists the service providers that support cellular connections.
The following output is displayed for show cellular status command:
cellular status
--------------card detect link
326 | show cellular
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
---- ------ ---Not-present Not-detect Linkdown
The output of this command includes the following parameters:
Parameters
Description
Card
Indicates if the cellular cards are currently configured on the W-IAP.
detect
Indicates if cellular modems are detected on the W-IAP
Link
Indicates the current status of cellular link.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show cellular | 327
show cert all
show cert all
Description
This command displays the details about the certificates uploaded on a W-IAP.
Usage Guidelines
Use this command to view information about the certificates uploaded to a W-IAP.
Example
The following example shows the output of show cert command:
Default Server Certificate:
Version :3
Serial Number :01:DA:52
Issuer :C=US, O=GeoTrust Inc., OU=Domain Validated SSL, CN=GeoTrust DV SSL CA
Subject :0x05=lLUge2fRPkWcJe7boLSVdsKOFK8wv3MF, C=US, O=securelogin.arubanetworks.com,
OU=GT28470348, OU=See www.geotrust.com/resources/cps (c)11, OU=Domain Control Validated QuickSSL(R) Premium, CN=securelogin.arubanetworks.com
Issued On :2011-05-11 01:22:10
Expires On :2017-08-11 04:40:59
Signed Using :SHA1
RSA Key size :2048 bits
Default CP Server Certificate:
Version :3
Serial Number :01:DA:52
Issuer :C=US, O=GeoTrust Inc., OU=Domain Validated SSL, CN=GeoTrust DV SSL CA
Subject :0x05=lLUge2fRPkWcJe7boLSVdsKOFK8wv3MF, C=US, O=securelogin.arubanetworks.com,
OU=GT28470348, OU=See www.geotrust.com/resources/cps (c)11, OU=Domain Control Validated QuickSSL(R) Premium, CN=securelogin.arubanetworks.com
Issued On :2011-05-11 01:22:10
Expires On :2017-08-11 04:40:59
Signed Using :SHA1
RSA Key size :2048 bits
The output of this command displays details such as the version, serial number, subject, issue date, expiry date,
type of encryption, and RSA key information for the certificates uploaded to the W-IAP.
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.1-4.0
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
328 | show cert all
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show clients
show clients [<diff>| accounting <mac>| checksum <mac>| debug| roaming| status <mac>| wired
[debug]]
Description
This command displays details about the W-IAP clients.
Syntax
Parameter
Description
<diff>
Displays difference summary of the client table since the specified interval.
accounting <mac>
Displays accounting information for a specific client MAC address.
checksum <mac>
Filters checksum errors for a specific client MAC address.
debug
Displays the W-IAP client configuration details, which can be used for debugging
purpose.
roaming
Displays information about roaming clients.
status <mac>
Displays the current status for a client based on the specified MAC address.
wired [debug]
Displays the list of clients connected to wired or Ethernet interface. You can also
use the optional debug parameter to view the end-to-end information of the wired
clients for debugging purpose.
Usage Guidelines
Use this command to view information about the W-IAP clients. The W-IAP client table provides basic information
about the clients. For detailed information of each client, use the required parameter and specify the MAC address of
the client.
Example
show clients and show clients wired
The following output is displayed for the show clients command:
Client List
----------Name IP Address MAC Address OS Network Access Point Channel
---- ---------- ----------- -- ------- ------------ ------10.17.88.226 08:ed:b9:e1:51:7d Network1 d8:c7:c8:cb:d4:20 44+
Type Role Signal Speed (mbps)
---- ---- ------ -----------AN admin1 51(good) 300(good)
Info timestamp :233732
A similar output is displayed for the show clients wired command.
The client list in the command output for both wireless and wired clients provides the following information:
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show clients | 329
Column
Description
Name
Displays the name of the client
IP address
Displays the IP address of the client.
MAC address
Displays the MAC address of the client.
OS
Indicates the OS running on the client system.
Network
Indicates the SSID and network to which the client is connected.
Access Point
Indicates the IP address of the Access Point to which the client is connected.
Channel
Indicates the channel assigned to the client.
Type
Indicates the type of the Wi-Fi client device.
Role
Indicates the role assigned to the client.
Signal
Indicates the current signal strength of the client, as detected by the W-IAP.
Speed(Mbps)
Indicates the current speed at which data is transmitted. When the client is
associated with a W-IAP, it constantly negotiates the speed of data transfer. A
value of 0 means that the W-IAP has not received any packets from the client for
some time.
show clients <diff>
The show clients <diff> command displays the change in the clients table data that occurred during the specified
interval. For example, if the value specified for <diff> parameter is 10 seconds, the client table displays the changes
such as signal strength or speed that occurred since the last 10 seconds.
show accounting <mac>
The show accounting <mac> command displays the accounting information such as status and session ID for a
specific client MAC address.
show checksum <mac>
The following output is displayed for the show checksum <mac> command:
Mac Address:08:ed:b9:e1:51:7d
Basic info
---------mac
--08 ed b9 e1 51 7d
bssid
d8 c7 c8 3d 3d 52
ap_ip
0a 11 58 ba
name
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00
essid
73 72 6f 79 2d 73 6f 6d 65 74 68 69 6e 67 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00
auth_failure_count
00
acl
330 | show clients
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
00 8a
acct_session
00 00 00 00 00 00 00
00 00 00 00 00 00 00
user_role
00 00 00 00 00 00 00
00 00 00 00 00 00 00
swarm_basic_client_t
08 ed b9 e1 51 7d d8
00 00 00 00 00 00 00
checksum
02 ec ba ec
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c7 c8 3d 3d 52 0a 11 58 ba 73 72 6f 79 2d 73 6f 6d 65 74 68 69 6e 67 00
00 00 00 00 00 00 00 00 00 00 00 00 00 8a a9 fe 5a 9a 03 e8 00 00
The show checksum <mac> command displays the checksum errors associated with the W-IAP clients.
show clients debug and show clients wired debug
The show clients debug command displays detailed information about the clients MAC and IP addresses, client
role, authentication aging time, and accounting intervals, ESSID and BSSID details, VLAN and multicast groups to
which the client is associated, and DHCP roles and options associated with the client. The show clients wired
debug command displays a similar output.
The following example shows the show clients debug command output:
Client List
----------Name IP Address MAC Address OS Network Access Point Channel
---- ---------- ----------- -- ------- ------------ ----169.254.90.154 08:ed:b9:e1:51:7d Network1 10.17.88.186 48Type Role Signal Speed (mbps) Auth Age Session Timeout ESSID
---- ---- ------ ------------ -------- --------------- --AN admin1 68(good) 6(poor) 0 0
Authenticated DEL Age Vlan Essid Private role info Accounting Session
------------- ---- ---- ---- ------ ------------ ----- ---------------------no no 5 333(SSID) () 0(0-0) 0
Name Accounting Start time BSSID Idle Timeout csum
---- --------------------- ------ ------------- ---d8:c7:c8:3d:3d:52 1000 0 2ecbaec(3)
mcast groups Acct Interval Class Attribute Dhcp-Opt Vlan
------------ ------------- ----------------- ------------224.0.0.252,239.255.255.250,224.0.0.251 0 null 0,(null) Dhcp-Opt role
--------- ,0,0-0
show clients status
The show clients status <mac> command displays the status of a W-IAP client.
show clients roaming
The show clients roaming command displays the MAC address and IP address details of W-IAP from which the
client has roamed and IP address of the W-IAP to which the client is roamed.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show clients | 331
Command History
Version
Description
Dell Networking W-Series
Instant 6.3.1.1-4.0
This command was modified.
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
332 | show clients
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show clock
show clock [summer-time| timezone all]
Description
This command displays the system clock, current timezone, and the daylight saving time configured on a W-IAP
Syntax
Parameter
Description
summer-time
Displays the summer (daylight saving) time settings.
timezone all
Displays the configured timezone for the W-IAP.
Usage Guidelines
Use this command to display the system clock. Include the optional summer-time parameter to display configured
daylight savings time settings. The timezone parameter shows the current timezone, with its time offset from
Greenwich Mean Time.
Example
show clock timezone all
The following example shows the partial output of show clock timezone all command:
Support Timezones
----------------Country Timezone DST Name DST Recurring
------- -------- -------- ------------International-Date-Line-West UTC-11
Coordinated-Universal-Time-11 UTC-11
Hawaii UTC-10
Alaska UTC-09 AKDT second sunday march 02:00 first sunday november 02:00
Baja-California UTC-08 MDT first sunday april 02:00 last sunday october 02:00
Pacific-Time UTC-08 PDT second sunday march 02:00 first sunday november 02:00
Arizona UTC-07
Chihuahua UTC-07 MDT first sunday april 02:00 last sunday october 02:00
La-Paz UTC-07 MDT first sunday april 02:00 last sunday october 02:00
Mazatlan UTC-07 MDT first sunday april 02:00 last sunday october 02:00
Mountain-Time UTC-07 MDT second sunday march 02:00 first sunday november 02:00
Central-America UTC-06
Central-Time UTC-06 CDT second sunday march 02:00 first sunday november 02:00
Guadalajara UTC-06 CDT first sunday april 02:00 last sunday october 02:00
Mexico-City UTC-06 CDT first sunday april 02:00 last sunday october 02:00
Monterrey UTC-06 CDT first sunday april 02:00 last sunday october 02:00
Saskatchewan UTC-06
Bogota UTC-05
Lima UTC-05
Quito UTC-05
Eastern-Time UTC-05 EDT second sunday march 02:00 first sunday november 02:00
Indiana(East) UTC-05 EDT second sunday march 02:00 first sunday november 02:00
The output of this command includes the following information:
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show clock | 333
Parameter
Description
Country
Displays the country name.
Timezone
Displays the name of the timezone.
DST Name
Displays the name of the Daylight Saving Time.
DST Recurring
Displays the name of the Daylight Saving recurring time.
show clock summer-time
The following example shows the partial output of show clock summer-time command:
Summer Time
----------DST Name Start Week Start Day Start Month Start Hour End Week End Day End Month End Hour
-------- ---------- --------- ----------- ---------- -------- ------- -------- ---------- --------- ----------- ---------- --------------- ---------- --------- ---------- ---------PST recurring 2 Sun Mar 2:00 first Sun Nov 3:00 -8
The output of this command includes the following information:
Parameter
Description
DST Name
Name of the Daylight Saving Time.
Start Week
Enter the week number when the time change begins.
Start Day
Enter the weekday when the time change begins.
Start Month
Enter the month when the time change begins.
Start Hour
Enter the hour when the time change begins.
End Week
Enter the week number when the time change ends.
End Day
Enter the weekday when the time change ends.
End Month
Enter the month when the time change ends.
End Hour
Enter the hour when the time change ends.
Related Commands
Command
Description
Mode
clock timezone
Configures timezones for the W-IAP.
Config mode
clock summer-time
Configures the summer-time for the
daylight savings time settings.
Config mode
334 | show clock
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show clock | 335
show configuration
show configuration
Description
This command displays the configuration saved on the W-IAP.
Usage Guidelines
Use this command to view the entire configuration saved on the W-IAP, including all wireless and wired profiles,
uplink configuration, ARM settings, radio profiles, ACLs, and interface settings.
Example
The following example displays the show configuration command output:
version 6.2.1.0-3.3.0.0
virtual-controller-country IN
virtual-controller-key e10e371601fae77a3ba78e44585d06c407f0a3e9a83835c1c4
name Instant-CB:D4:20
terminal-access
clock timezone none 00 00
rf-band all
allow-new-aps
allowed-ap d8:c7:c8:cb:d4:20
allowed-ap d8:c7:c8:cb:d3:98
allowed-ap d8:c7:c8:cb:d3:b4
routing-profile
route 192.0.2.0 255.0.0.0 192.0.2.1
arm
wide-bands 5ghz
a-channels 56,60,64,149,153,157,161,165,36+,44+,149+,157+
g-channels 11,1+,7+
min-tx-power 18
max-tx-power 127
band-steering-mode prefer-5ghz
air-time-fairness-mode fair-access
client-aware
scanning
syslog-level debug ap-debug
syslog-level debug network
syslog-level debug security
syslog-level debug system
syslog-level debug user
syslog-level debug user-debug
syslog-level debug wireless
mgmt-user admin 16e8d1cbd13f13a18cd1adb8b0d23022
wlan access-rule default_wired_port_profile
rule any any match any any any permit
wlan access-rule wired-instant
rule 192.0.2.1 255.255.255.255 match tcp 80 80 permit
rule 192.0.2.2 255.255.255.255 match tcp 4343 4343 permit
rule any any match udp 67 68 permit
rule any any match udp 53 53 permit
wlan access-rule rule-1
rule any any match any any any permit
wlan access-rule rule-local-nw
rule any any match any any any permit
hotspot anqp-nai-realm-profile "test"
enable
nai-realm-name ""
336 | show configuration
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
nai-realm-eap-method eap-ttls
nai-realm-auth-id-1 non-eap-inner-auth
nai-realm-auth-value-1 mschapv2
nai-realm-auth-id-2 credential
nai-realm-auth-value-2 uname-passward
nai-realm-encoding utf8
no nai-home-realm
hotspot anqp-nwk-auth-profile "test"
enable
nwk-auth-type http-redirect
url "http:///"
hotspot anqp-3gpp-profile "test"
enable
3gpp-plmn1 ""
3gpp-plmn2 ""
3gpp-plmn3 ""
3gpp-plmn4 ""
3gpp-plmn5 ""
3gpp-plmn6 ""
hotspot anqp-ip-addr-avail-profile "test"
enable
ipv4-addr-avail
no ipv6-addr-avail
hotspot h2qp-wan-metrics-profile "test"
enable
wan-metrics-link-status (null)
no symm-link
no at-capacity
uplink-speed 0
downlink-speed 0
uplink-load 0
downlink-load 0
load-duration 0
hotspot hs-profile "test"
enable
no comeback-mode
no asra
no internet
no pame-bi
no group-frame-block
no p2p-dev-mgmt
no p2p-cross-connect
query-response-length-limit 127
access-network-type private
venue-group business
venue-type research-and-dev-facility
roam-cons-len-1 0
roam-cons-oi-1 ""
roam-cons-len-2 0
roam-cons-oi-2 ""
roam-cons-len-3 0
roam-cons-oi-3 ""
wlan ssid-profile profile-1
enable
index 0
type employee
essid profile-1
wpa-passphrase c52acfeb3e59ef254a6d14fe2ad565382e46f7eecde33af3
opmode wpa2-psk-aes
max-authentication-failures 0
vlan 333
rf-band all
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show configuration | 337
captive-portal disable
dtim-period 1
inactivity-timeout 1000
broadcast-filter none
external-server
bandwidth-limit 65535
dmo-channel-utilization-threshold 90
local-probe-req-thresh 0
max-clients-threshold 64
wlan ssid-profile profile-local-nw
enable
index 1
type employee
essid profile-local-nw
wpa-passphrase dd4da86c25c31bf83417024a338982ed4f01e1751e7a4502
opmode wpa2-psk-aes
max-authentication-failures 0
vlan 2
auth-server InternalServer
rf-band all
captive-portal disable
dtim-period 1
inactivity-timeout 1000
broadcast-filter none
dmo-channel-utilization-threshold 90
local-probe-req-thresh 0
max-clients-threshold 64
auth-survivability cache-time-out 24
wlan external-captive-portal
server localhost
port 80
url "/"
auth-text "Authenticated"
auto-whitelist-disable
blacklist-time 3600
auth-failure-blacklist-time 3600
ids classification
ids
wireless-containment none
ip dhcp something-vlan10
server-type Centralized,L2
server-vlan 333
ip dhcp local-vw-vlan2
server-type Local
server-vlan 2
subnet 192.0.2.5
subnet-mask 255.255.255.0
wired-port-profile wired-instant
switchport-mode access
allowed-vlan all
native-vlan guest
no shutdown
access-rule-name wired-instant
speed auto
duplex auto
no poe
type guest
captive-portal disable
no dot1x
wired-port-profile default_wired_port_profile
switchport-mode trunk
allowed-vlan all
338 | show configuration
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
native-vlan 1
shutdown
access-rule-name default_wired_port_profile
speed auto
duplex full
no poe
type employee
captive-portal disable
no dot1x
enet0-port-profile default_wired_port_profile
uplink
preemption
enforce none
failover-internet-pkt-lost-cnt 10
failover-internet-pkt-send-freq 30
failover-vpn-timeout 180
airgroup
enable
airgroupservice airplay
disable
description AirPlay
airgroupservice airprint
disable
description AirPrint
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show configuration | 339
show config-status
show config-status
Description
This command displays the details about the configuration status of a W-IAP.
Usage Guidelines
Use this command to view the current configuration status of the W-IAP in flash memory.
Example
The following example shows the output of the show config-status command:
Config Status
------------Config Name Compressed
----------- ---------Primary No
Backup No
The backup configuration is used when the primary configuration is lost. And the Compressed option indicates that
the configuration file has been compressed if the file size is large.
Command History
Version
Description
Dell Networking W-Series Instant 6.4.0.24.1
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
340 | show config-status
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show console-settings
show console-settings
Description
This command displays the details about the console settings of a W-IAP.
Usage Guidelines
Use this command to view if the access to W-IAP console is enabled or disabled.
Example
The following example shows the output of the show console-settings command:
(Instant AP)# show console-settings
Console Setting
--------------Status
-----enabled
Command History
Version
Description
Dell Networking W-Series Instant 6.4.0.24.1
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show console-settings | 341
show country-codes
show country-codes
Description
This command shows the country code for the W-IAP. The country code specifies allowed channels for that country.
Usage Guidelines
Use this command to view a list of W-IAP country codes.
Example
The following example shows the output of show country-codes command .
CA:Canada
DE:Germany
NL:Netherlands
IT:Italy
PT:Portugal
LU:Luxembourg
NO:Norway
SE:Sweden
FI:Finland
DK:Denmark
CH:Switzerland
CZ:Czech Republic
BE:Belgium
ES:Spain
GB:United Kingdom
KR:Republic of Korea (South Korea)
CN:China
FR:France
HK:Hong Kong
SG:Singapore
TW:Taiwan
MY:Malaysia
BR:Brazil
SA:Saudi Arabia
LB:Lebanon
AE:United Arab Emirates
ZA:South Africa
AR:Argentina
AU:Australia
AT:Austria
BO:Bolivia
CL:Chile
GR:Greece
HU:Hungary
IS:Iceland
IN:India
IE:Ireland
KW:Kuwait
LV:Latvia
LI:Liechtenstein
LT:Lithuania
MX:Mexico
MA:Morocco
NZ:New Zealand
PL:Poland
PR:Puerto Rico
342 | show country-codes
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
SK:Slovak Republic
SI:Slovenia
TH:Thailand
UY:Uruguay
PA:Panama
RU:Russia
EG:Egypt
TT:Trinidad and Tobago
TR:Turkey
CR:Costa Rica
EC:Ecuador
HN:Honduras
KE:Kenya
UA:Ukraine
VN:Vietnam
BG:Bulgaria
CY:Cyprus
EE:Estonia
MT:Malta
MU:Mauritius
RO:Romania
CS:Serbia and Montenegro
ID:Indonesia
PE:Peru
VE:Venezuela
JM:Jamaica
BH:Bahrain
OM:Oman
JO:Jordan
BM:Bermuda
CO:Colombia
DO:Dominican Republic
GT:Guatemala
PH:Philippines
LK:Sri Lanka
SV:El Salvador
TN:Tunisia
MO:Macau
PK:Islamic Republic of Pakistan
QA:Qatar
DZ:Algeria
NG:Nigeria
HR:Croatia
GH:Ghana
BA:Bosnia and Herzegovina
MK:Macedonia
MI:Maritime Offshore
MB:Maritime Forward Operating Base
KZ:Kazakhstan
TD:Chad
ML:Mali
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show country-codes | 343
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
344 | show country-codes
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show cpcert
show 1xcert
Description
This command displays the details of the captive portal server certificate, which is used by the W-IAP for guest
authentication.
Usage Guidelines
Use this command to view information about the captive portal server certificate uploaded on W-IAP.
Example
The following example shows the default certificate details of the captive portal server in the output of the show
cpcert command:
Default Server Certificate:
Version :3
Serial Number :01:DA:52
Issuer :C=US, O=GeoTrust Inc., OU=Domain Validated SSL, CN=GeoTrust DV SSL CA
Subject :0x05=lLUge2fRPkWcJe7boLSVdsKOFK8wv3MF, C=US, O=securelogin.arubanetworks.com,
OU=GT28470348, OU=See www.geotrust.com/resources/cps (c)11, OU=Domain Control Validated QuickSSL(R) Premium, CN=securelogin.arubanetworks.com
Issued On :2011-05-11 01:22:10
Expires On :2017-08-11 04:40:59
Signed Using :SHA1
RSA Key size :2048 bits
The output of this command describes details such as the version, serial number, subject, issue date, expiry date,
type of encryption, and RSA key information for the certificates uploaded to the W-IAP.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.4
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show cpcert | 345
show cpu
show cpu [details]
Description
This command displays the CPU details.
Syntax
Parameter
Description
[details]
Include this optional parameter at the request of Dell technical support to
display additional CPU troubleshooting statistics.
Usage Guidelines
Use this command to view CPU load for application and system processes.
Example
The following example shows the output of show cpu command:
user 0% nice 8% system 1% idle 89% io 0% irq 0% softirq 2%
The following example shows the output of show cpu details command:
Mem: 66488K used, 59668K free, 0K shrd, 0K buff, 22540K cached
Load average: 0.12 0.09 0.09 (Status: S=sleeping R=running, W=waiting)
PID USER STATUS RSS PPID %CPU %MEM COMMAND
1434 root R N 5540 1377 8.3 4.3 sapd
13137 root R < 356 12694 2.3 0.2 top
1430 root R < 7256 1377 0.0 5.7 cli
12694 root S < 2880 12685 0.0 2.2 cli
1429 root S 2508 1 0.0 1.9 cli
1682 root S < 2392 1377 0.0 1.8 radiusd-term
1699 root S < 2384 1377 0.0 1.8 radiusd
1442 root S < 2092 1377 0.0 1.6 snmpd
1436 root S < 1804 1377 0.0 1.4 stm
1449 root S < 1472 1377 0.0 1.1 meshd
1413 root R N 1408 1377 0.0 1.1 awc
1448 root S < 1332 1377 0.0 1.0 lldpd
1445 root S < 1164 1377 0.0 0.9 mdns
1259 root S 948 1 0.0 0.7 tinyproxy
1377 root S < 844 1 0.0 0.6 nanny
1450 root S < 796 1377 0.0 0.6 hostapd
1281 root S < 748 1 0.0 0.5 mini_httpd
1284 root S < 740 1 0.0 0.5 mini_httpd
1278 root S < 728 1 0.0 0.5 mini_httpd
1382 root S < 688 1377 0.0 0.5 msgHandler
1451 root S < 624 1377 0.0 0.4 wpa_supplicant
The output of this command shows the percentage of CPU utilization.
346 | show cpu
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show cpu | 347
show datapath
show datapath {acl <ID>|acl-all|acl-allocation|acl-rule <rule>|acl-ruledetail<acl>|bridge|dmo-session|dmo-station <mac>|mcast|nat-pool <ID>|route
session|statistics|user|vlan}
Descriptions
This command shows the system statistics for your W-IAP.
Syntax
Parameter
Description
acl <ID>
Displays datapath statistics associated with a specified ACL.
acl-all
Displays datapath statistics associated with all ACLs.
acl-allocation
Displays ACL table allocation details.
acl-rule <rule>
Displays the name of the ACL.
acl-rule-detail <acl>
Displays the ACL rule details.
bridge
Shows bridge table entry statistics including MAC address, VLAN, assigned
VLAN, Destination and flag information for an AP.
dmo-session
Displays details of a DMO session.
dmo-station <mac>
Displays details of a DMO station.
mcast
Displays multicast table statistics for the W-IAP.
nat-pool <ID>
Displays the contents of the datapath NAT entries table. It displays NAT pools
as configured in the datapath. Statistics include pool, SITP start, SIP end and
DIP.
route
Displays datapath route table statistics.
session
Displays datapath session statistics.
statistics
Displays datapath station association table statistics.
user
Displays datapath user statistics such as current entries, pending deletes, high
water mark, maximum entries, total entries, allocation failures, invalid users
and maximum link length.
vlan
Displays VLAN table information such as VLAN memberships inside the
datapath including L2 tunnels which tunnel L2 traffic.
Usage Guidelines
Use the show datapath command to display various datapath statistics for debugging purposes
Examples
show datapath acl
The following example shows the output of show datapath acl command.
348 | show datapath
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Datapath ACL 3 Entries
----------------------Flags: P - permit, L - log, E - established, M/e - MAC/etype filter
S - SNAT, D - DNAT, R - redirect, r - reverse redirect m - Mirror
I - Invert SA, i - Invert DA, H - high prio, O - set prio, C - Classify Media
A - Disable Scanning, B - black list, T - set TOS, 4 - IPv4, 6 - IPv6
----------------------------------------------------------------
show datapath acl-all
The following example shows the output of show datapath acl-all command.
ACL Name {magic-vlan} Number {106}
1: any any 17 0-65535 8209-8211 P4
2: 192.168.10.0 255.255.254.0 192.168.10.0 255.255.254.0 any P4
3: 192.168.10.0 255.255.254.0 224.0.0.0 224.0.0.0 any P4
4: 192.168.10.0 255.255.254.0 any any PS4
5: any any any P4 hits 2127
---------------------------------------------------------------ACL Name {internal-cp-magic} Number {107}
1: any 192.168.10.1 255.255.255.255 6 0-65535 80-80 PSD4
2: any 192.168.10.1 255.255.255.255 6 0-65535 443-443 PSD4
3: any any 6 0-65535 80-80 PSD4
4: any any 6 0-65535 443-443 PSD4
5: 192.168.10.0 255.255.254.0 192.168.10.0 255.255.254.0 17 0-65535 67-68 P4
6: 192.168.10.0 255.255.254.0 224.0.0.0 224.0.0.0 17 0-65535 67-68 P4
7: 192.168.10.0 255.255.254.0 any 17 0-65535 67-68 PS4
8: any any 17 0-65535 67-68 P4
9: 192.168.10.0 255.255.254.0 192.168.10.0 255.255.254.0 17 0-65535 53-53 P4
10: 192.168.10.0 255.255.254.0 224.0.0.0 224.0.0.0 17 0-65535 53-53 P4
11: 192.168.10.0 255.255.254.0 any 17 0-65535 53-53 PS4
12: any any 17 0-65535 53-53 P4
13: 192.168.10.0 255.255.254.0 192.168.10.0 255.255.254.0 6 0-65535 8081-8081 P4
14: 192.168.10.0 255.255.254.0 224.0.0.0 224.0.0.0 6 0-65535 8081-8081 P4
15: 192.168.10.0 255.255.254.0 any 6 0-65535 8081-8081 PS4
16: any any 6 0-65535 8081-8081 P4
17: any any any 4
---------------------------------------------------------------ACL Name {external-cp-magic} Number {108}
1: any 192.168.10.1 255.255.255.255 6 0-65535 80-80 PSD4
2: any 192.168.10.1 255.255.255.255 6 0-65535 443-443 PSD4
3: any any 6 0-65535 80-80 PSD4
4: any any 6 0-65535 443-443 PSD4
5: 192.168.10.0 255.255.254.0 192.168.10.0 255.255.254.0 17 0-65535 67-68 P4
6: 192.168.10.0 255.255.254.0 224.0.0.0 224.0.0.0 17 0-65535 67-68 P4
7: 192.168.10.0 255.255.254.0 any 17 0-65535 67-68 PS4
8: any any 17 0-65535 67-68 P4
9: 192.168.10.0 255.255.254.0 192.168.10.0 255.255.254.0 17 0-65535 53-53 P4
10: 192.168.10.0 255.255.254.0 224.0.0.0 224.0.0.0 17 0-65535 53-53 P4
11: 192.168.10.0 255.255.254.0 any 17 0-65535 53-53 PS4
12: any any 17 0-65535 53-53 P4
13: 192.168.10.0 255.255.254.0 192.168.10.0 255.255.254.0 6 0-65535 8081-8081 P4
14: 192.168.10.0 255.255.254.0 224.0.0.0 224.0.0.0 6 0-65535 8081-8081 P4
15: 192.168.10.0 255.255.254.0 any 6 0-65535 8081-8081 PS4
16: any any 6 0-65535 8081-8081 P4
17: any any any 4
----------------------------------------------------------------
show datapath acl-allocation
The following example shows the output of show datapath acl-allocation command.
ACL ACE Start ACE Block Size
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show datapath | 349
---- ---------- --------------105 3200 32
103 3234 16
107 3250 32
104 3282 16
108 3298 32
100 3330 2
101 3332 4
102 3336 4
134 3340 4
135 3344 8
136 3352 4
143 3360 8
145 3372 8
130 3380 16
131 3412 16
132 3444 16
133 3476 16
137 3508 8
139 3520 8
141 3532 8
146 3540 4
147 3544 8
148 3552 4
149 3556 8
150 3564 4
151 3568 4
152 3572 4
153 3576 4
138 3580 8
140 3588 8
142 3596 8
144 3604 8
106 3612 8
show datapath acl-rule
The following example shows the output of show datapath acl-rule command.
Datapath SSID: test ACL Entries
---------------------------------------------------------------Flags: P - permit, L - log, E - established, M/e - MAC/etype filter
S - SNAT, D - DNAT, R - redirect, r - reverse redirect m - Mirror
I - Invert SA, i - Invert DA, H - high prio, O - set prio, C - Classify Media
A - Disable Scanning, B - black list, T - set TOS, 4 - IPv4, 6 - IPv6
---------------------------------------------------------------ACL Name {test 0} Number {142}
1: any any 17 0-65535 8209-8211 P4
2: 192.168.10.0 255.255.254.0 192.168.10.0 255.255.254.0 any P4
3: 192.168.10.0 255.255.254.0 224.0.0.0 224.0.0.0 any P4
4: 192.168.10.0 255.255.254.0 any any PS4
5: any any any P4
---------------------------------------------------------------ACL Name {test 1} Number {143}
1: any any 17 0-65535 8209-8211 P4
2: 192.168.10.0 255.255.254.0 192.168.10.0 255.255.254.0 any P4
3: 192.168.10.0 255.255.254.0 224.0.0.0 224.0.0.0 any P4
4: 192.168.10.0 255.255.254.0 any any PS4
5: any any any P4
---------------------------------------------------------------ACL Name {test 2} Number {144}
1: any any 17 0-65535 8209-8211 P4
2: 192.168.10.0 255.255.254.0 192.168.10.0 255.255.254.0 any PT4
350 | show datapath
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
3: 192.168.10.0 255.255.254.0 224.0.0.0 224.0.0.0 any PT4
4: 192.168.10.0 255.255.254.0 any any PST4
5: any any any PT4
---------------------------------------------------------------ACL Name {test 3} Number {145}
1: any any 17 0-65535 8209-8211 P4
2: 192.168.10.0 255.255.254.0 192.168.10.0 255.255.254.0 any PT4
3: 192.168.10.0 255.255.254.0 224.0.0.0 224.0.0.0 any PT4
4: 192.168.10.0 255.255.254.0 any any PST4
5: any any any PT4
----------------------------------------------------------------
show datapath bridge
The following example shows the output of show datapath bridge command.
Datapath Bridge Devices
----------------------------Flags: F - source-filter, T - trusted, Q - tagged, I - IP
S - split-tunnel, B - bridge, M - mesh, P - PPPoE
C - content-filter, O - corp-access, h - to HAP, f - to FAP
h - dhcp-redirect
Dev Name VLANs PVID ACLs FramesRx FramesTx Flags
--- ------------------------ ----- ---- ------ -------- -------- -------3 bond0 1 1 0/0 618048 95826 FTQB
8 br0 0 1 105/0 95432 0 IB
11 aruba002 1 1 100/0 0 176788 B
12 aruba102 1 1 100/0 0 140373 B
13 aruba003 1 1 100/0 0 139236 B
14 aruba103 1 1 100/0 0 0 B
Datapath Bridge Table Entries
----------------------------Flags: P - Permanent, D - Deny, R - Route, M - Mobile, X - Xsec, A - Auth
AP Flags: X - Awaiting 1X reply, B - Block all non-1X traffic, F - Force bridge role
MAC VLAN Assigned VLAN Destination Flags AP Flags Bridge Role ACL
----------------- ---- ------------- ----------- ----- -------- --------------00:1A:1E:0D:7E:D3 1 1 dev3 0
D8:C7:C8:C4:42:98 1 1 local P 0
D8:C7:C8:C4:42:98 3333 3333 local P 0
00:0B:86:40:1C:A0 1 1 dev3 0
6C:F3:7F:C3:5C:12 64 64 dev3 0
show datapath dmo-session
The following example shows the output of show datapath dmo-session command.
MCAST Groups:
-------------Source Group Vlan Age[s] BSSs Received Multicast Converted Unicast Dropped _Stas _l2grp _l3grp
DMO queue: size:256, dropped:0, rescheduled:0, length:0, high-water:0
DMO Sessions:
-------------
show datapath dmo-station
The following example shows the output of show datapath dmo-station command.
Group Ref_count Position
show datapath mcast
The following example shows the output of show datapath mcast command.
Dev Vlans
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show datapath | 351
-------- ---------------------dev3 1
dev11 1
dev12 1
dev13 1
dev14 1
show datapath nat-pool
The following example shows the output of show datapath nat-pool command.
Datapath NAT Pool Entries
------------------------ID Begin Source IP End Source IP Destination IP Flags
-- --------------- ------------- -------------- -----
show datapath route
The following example shows the output of show datapath route command.
Route Table Entries
------------------Flags: L - Local, P - Permanent, T - Tunnel, I - IPsec, M - Mobile, A - ARP, D - Drop
IP Mask Gateway Cost VLAN Flags
--------------- --------------- --------------- ---- ---- ----0.0.0.0 0.0.0.0 10.17.88.2 0 0
192.168.10.0 255.255.254.0 192.168.10.1 0 3333 D
0.0.0.0 255.255.255.192 10.17.88.59 0 1 L
Route Cache Entries
------------------Flags: L - local, P - Permanent, T - Tunnel, I - IPsec, M - Mobile, A - ARP, D - Drop
IP MAC VLAN Flags
--------------- ----------------- ----------- ----10.17.88.2 00:0B:86:40:1C:A0 1 A
10.17.88.59 D8:C7:C8:C4:42:98 1 LP
192.168.10.1 D8:C7:C8:C4:42:98 3333 LP
show datapath session
The following example shows the output of show datapath session command.
Datapath Session Table Entries
-----------------------------Flags: F - fast age, S - src NAT, N - dest NAT
D - deny, R - redirect, Y - no syn
H - high prio, P - set prio, T - set ToS
C - client, M - mirror, V - VOIP
I - Deep inspect, U - Locally destined
s - media signal, m - media mon, a - rtp analysis
RAP Flags: 0 - Q0, 1 - Q1, 2 - Q2
Source IP Destination IP Prot SPort DPort Cntr Prio ToS Age Destination TAge Flags
-------------- -------------- ---- ----- ----- ---- ---- --- --- ----------- ---- ----10.17.88.59 10.13.110.198 6 22 62719 0 0 0 0 dev3 733
10.17.88.59 10.0.0.1 6 64104 443 0 0 0 1 local 5b YC
10.13.110.198 10.17.88.59 6 62719 22 0 0 0 0 dev3 733 C
10.13.23.237 10.17.88.59 6 55302 22 0 0 0 0 dev3 8be C
10.17.88.59 10.13.23.237 6 22 55302 0 0 0 0 dev3 8be
10.0.0.1 10.17.88.59 6 443 64104 0 0 0 1 local 5b Y
show datapath statistics
The following example shows the partial output of show datapath statistics command.
Datapath Counters
--------------------352 | show datapath
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Counter Value
------- -----Tagged frames dropped on untagged interface 0
Frames dropped for being too short 0
Frames received on port not in VLAN 0
Non-dot1x frames dropped during L2 blocking 0
Frames dropped for ingress change on permanent bridge entry 0
Frames received on port not in VLAN 0
Unicast frames filtered 86
Frames dropped due to FP firewall 6
Frames that failed FP spoofing check 0
Frames dropped with logging 0
Frames dropped due to unknown FP opcode 0
Frames freed by FP 3
Frames that failed SP spoofing check 0
Frames dropped due to excessive user misses 0
Frames dropped due to no buffers 0
Frames dropped due to no 'br0' device 0
Frames dropped due to no stack IP address 0
Frames dropped while user miss pending 0
Frames dropped when user entry creation failed 0
Frames dropped due to unknown FP opcode 0
Frames dropped due to initial IP route lookup failure 0
Frames dropped due to final IP route lookup failure 0
Frames dropped due to ARP processing failure 0
Frames dropped due to illegal device index 0
Frames dropped due to interface being down 0
Unicast frames not bridged due to split-tunnel destination 0
Unicast frames from bridge role user dropped 0
Unicast frames that could not be bridged to split tunnel 0
Frames dropped due to missing PPP device 0
Frames dropped due to pullup failure 0
Frames dropped due to misalignment 0
Frames received by firewall 715679
DHCP frames on DHCP local VLAN 96041
PPPOE frames to session processing 0
Frames needing bridging 716075
Mesh frames forwarded 0
Thin AP frames forwarded 0
Frames to session processing 718714
Frames to SP 21792
Frames bridged by SP 396
Frames routed by SP 0
Frames for SP session processing 17454
Frames for FP application processing 3942
Frames bridged by FP 0
Frames for FP session processing 2725
Frames routed by FP 18577
FP user misses 73
Frames not tunneled from bridge role user 0
SP user misses 73
Frames to DHCP 18
Frames to DNS 0
Frames held 0
Frames needed routing 715572
Frames needed forwarding 634373
Frames redirected to CSS tunnel 0
Frames sent by firewall 94681
Frames delivered to stack 82061
Frames delivered to CP 0
Frames to be flooded 538842
Frames potentially needing flooding 637659
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show datapath | 353
show datapath user
The following example shows the partial output of show datapath user command.
Datapath User Table Entries
--------------------------Flags: P - Permanent, W - WEP, T- TKIP, A - AESCCM
R - ProxyARP to User, N - VPN, L - local
FM(Forward Mode): S - Split, B - Bridge, N - N/A
IP MAC ACLs Contract Location Age Sessions Flags Vlan FM
--------------- ----------------- ------- --------- -------- ----- --------- ----- ---- -10.17.88.59 D8:C7:C8:C4:42:98 105/0 0/0 0 0 1/65535 1 N
0.0.0.0 D8:C7:C8:C4:42:98 105/0 0/0 0 0 0/65535 P 1 N
192.168.10.1 D8:C7:C8:C4:42:98 105/0 0/0 0 11115 0/65535 P 3333 B
show datapath vlan
The following example shows the partial output of show datapath vlan command.
Datapath VLAN Table Entries
--------------------------Flags: N - Nat Inside, M - Route Multicast, R - Routing
S - Snoop MLD, G - Snoop IGMP, P - Proxy IGMP
VLAN Flags Ports
---- ------ ----1 R dev3
1 R dev11
1 R dev12
1 R dev13
1 R dev14
The outputs of the show datapath command indicates the following:
l
ACL table allocation details for the W-IAP.
l
AP Datapath ACL Tables
l
List of ACL rules configured for the SSID and Ethernet port profiles.
l
Bridge table entry statistics including MAC address, VLAN, assigned VLAN, destination and flag information for
the W-IAP.
l
Details of a DMO session.
l
Multicast table statistics for the W-IAP.
l
Route table statistics for the W-IAP.
l
Datapath session table statistics for the W-IAP
l
Hardware packet statistics for the W-IAP.
l
Datapath user statistics such as current entries, pending deletes, high water mark, maximum entries, total
entries, allocation failures, invalid users, and maximum link length for the W-IAP.
l
VLAN table information such as VLAN memberships inside the datapath including L2 tunnels for the W-IAP.
Command History
Version
Description
Dell Networking W-Series
Instant 6.3.1.1-4.0
This command is modified.
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
354 | show datapath
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show datapath | 355
show delta-config
show delta-config cfgid
Description
This command displays the difference between the current configuration in the current CLI session and the
configuration that is saved on the W-IAP.
Usage Guidelines
Use this command to view the difference between the current configuration information stored in the W-IAP flash
memory and the configuration information saved in the W-IAP memory.
Example
The following example shows the output of the show delta-config command:
103-Master# show delta-config
IAP delta configuration current_config_id:7
IAP delta configuration top_config_id:7
Command History
Version
Description
Dell Networking W-Series
Instant 6.4.0.2-4.1
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
356 | show delta-config
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show derivation-rules
show derivation-rules
Description
This command displays the list of role and VLAN derivation rules configured for the WLAN SSIDs and wired profiles
in a W-IAP.
Usage Guidelines
Use this command to view the derivation rules configured for a network profile.
Example
The following example shows the output of the show derivation-rules command:
SSID:Example1
Role Derivation Rules
--------------------Attribute Operation Operand Role Name Index Hits
-------- --------- ------- --------- ----- ---Filter-Id contains 123456 Example1 8 0
AP-Name contains instant instant 9 0
Vlan Derivation Rules
--------------------Attribute Operation Operand Vlan Id Hits
-------- --------- ------- ------- ---AP-Group contains instant 200 0
Filter-Id contains 123456 200 0
The output of the command provides a list of role and VLAN derivation rules configured for each SSID and wired
profile.
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.4
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show derivation-rules | 357
show dhcp-allocation
show dhcp-allocation
Description
This command displays information about the DHCP address allocation.
Usage Guidelines
Use this command to view DHCP address allocation for network address translated clients to allow mobility of the
clients across W-IAPs.
Example
The following example shows the output of show dhcp-allocation command:
(Instant AP)# show dhcp-allocation
---------------------/etc/dnsmasq.conf-------------------listen-address=127.0.0.1
addn-hosts=/etc/ld_eth_hosts
addn-hosts=/etc/ld_ppp_hosts
dhcp-src=192.168.10.1
dhcp-leasefile=/tmp/dnsmasq.leases
dhcp-authoritative
filterwin2k
#magic-vlan
{
vlan-id=3333
dhcp-range=192.168.10.3,192.168.11.254,255.255.254.0,12h
dhcp-option=1,255.255.254.0
dhcp-option=3,192.168.10.1
dhcp-option=6,10.1.1.50
dhcp-option=54,192.168.10.1
}
---------------------/tmp/dnsmasq.leases------------------
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
358 | show dhcp-allocation
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show dhcpc-opts
show dhcpc-opts
Description
This command displays the DHCP options configured on a W-IAP.
Usage Guidelines
Use this command to view the current status of the vendor-specific DHCP options configured on a W-IAP. The
DHCP options are configured and enabled for assignment and distribution to DHCP clients based on the type of
DHCP server, scope, and clients.
Example
The following output is displayed for the show dhcpc-opts command:
-------------------DHCP option43 -------------------Not available
The output of this command displays the vendor-specific DHCP option configured for a DHCP scope and the current
status of the DHCP option.
Command History
Version
Description
Dell Networking WSeries Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show dhcpc-opts | 359
show dhcps config
show dhcps config
Description
This command provides information about the DHCP scopes configured for a W-IAP.
Usage Guidelines
Use this command to view configuration details associated with the DHCP scopes enabled on a W-IAP.
Example
The following example shows the output of the show dhcps config command:
Distributed DHCP Scopes
----------------------Name Type VLAN Netmask Default Router DNS Server Domain Name
---- ---- ---- ------- -------------- ---------- ----------dhcp-11 Distributed,L2 11 11.11.11.0 255.255.255.0 0.0.0.0
Lease Time IP Address Range Client Count DHCP Option Reserve First Reserve Last
---------- ----------------- ----------- ------------- ------------ -----43200 5 None
Branch ID Branch Netmask Branch Router DHCP Host
--------- -------------- ------------- --------Centralized DHCP Scopes
----------------------Name Type VLAN DHCP Relay DHCP Relay Servers DHCP Option 82 VLAN IP VLAN Mask Split Tunnel
---- ---- ---- ---------- ------------------ -------------- ------- --------- -----------Local DHCP Scopes
----------------Name Type VLAN Network Netmask Exclude Address DNS Server Domain Name Lease Time DHCP Option
---- ---- ---- ------- ------- --------------- ---------- ----------- -- -------- ----------local Local 12 12.12.12.0 255.255.255.0 0.0.0.0 0.0.0.0
DHCP Host DNS Cache
--------- --------None
The output of this command displays the following information:
Parameter
Description
Name
Displays the name of the DHCP scope.
type
Displays the DHCP assignment modes. The current
release of Instant supports the following DHCP assignment
modes.
l
l
l
l
l
VLAN
360 | show dhcps config
Distributed, L2
Distributed, L3
Local
Local, L3
Centralized, L2
Indicates the VLAN ID assigned to DHCP scope.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Parameter
Description
Netmask
Displays the subnet mask.
DNS Server
Displays the DNS server IP address.
Domain Name
Displays the domain name configured for the DHCP
scope.
Default router
Displays the IP address of the default router.
lease-time
Displays the lease-time configured for the DHCP clients.
IP Address Range
Displays the range of IP addresses configured for the
distributed DHCP scopes.
client-count <number>
Displays the number of clients allowed per DHCP branch.
DHCP Option
Displays the DHCP option if configured.
Reserve First and Reserve Last
Displays the first few and the last few IP addresses
reserved in the subnet.
Branch ID
Displays the DHCP branch ID.
Branch Netmask
Displays the branch subnet mask.
Branch Router
Displays the IP address if the branch router.
Exclude IP address
Displays the excluded IP address. The value displayed in
this determines the exclusion range of the subnet. Based
on the size of the subnet, the IP addresses that come
before or after the IP address value specified in this field
are excluded.
DHCP Relay
Displays the DHCP relay information that enables the WIAPs to intercept the broadcast packets and relay DHCP
requests directly to corporate network.
DHCP Relay Server
Displays the IP address of the corporate DHCP server for
the DHCP request relay.
Split Tunnel
Indicates if the split-tunnel function is enabled or disabled.
DHCP Host
Indicates the DHCP host name if configured.
DNS cache
Indicates if DNS caching is enabled or disabled.
Command History
Version
Description
Dell Networking W-Series Instant 6.4.0.24.1
This command was modified.
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show dhcps config | 361
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
362 | show dhcps config
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show dhcp subnets
show dhcp subnets
Description
This command displays the subnet details and the gateway IP for distributed L2 and L3 networks.
Usage Guidelines
Use this command to view the subnet details for the distributed,l2 and l3 networks.
Example
The following example shows the output of the show dhcp subnets command:
DHCP Subnet Table
----------------VLAN Type Subnet Mask Gateway Mode Rolemap
---- ---- ------ ---- ------- ---- ------532 l2 192.168.132.0 255.255.255.0 0.0.0.0 remote,full-tunnel VLAN532
539 nat 192.168.1.0 255.255.255.0 192.168.1.1 local,split-tunnel VLAN532
538 l3 192.168.2.0 255.255.255.0 192.168.2.1 local,split-tunnel VLAN532
534 l2 0.0.0.0 255.255.255.255 0.0.0.0 remote,full-tunnel VLAN532
The output of this command displays the following information:
Parameter
Description
VLAN
Displays the VLAN details.
Type
Displays the type of DHCP assignment mode.
Subnet
Displays the subnet details.
Mask
Displays the subnet mask details.
DNS Server
Displays the DNS server IP address.
Gateway
Displays the gateway IP address.
Mode
Displays details of the tunnel mode.
Rolemap
Displays the role assigned to the clients.
Command History
Version
Description
Dell Networking W-Series Instant 6.4.0.24.1
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show dhcp subnets | 363
show distributed-dhcp-branch-counts
show distributed-dhcp-branch-counts <type> <sip> <eip>
Description
This command displays the branch count for the distributed DHCP scopes configured on a W-IAP.
Syntax
Parameter
Description
type
Displays the branch details for the distributed DHCPs based on the type of the DHCP
scope specified. The current release of Instant supports the following distributed DHCP
assignment modes.
l
l
<sip>
<eip>
Distributed, L2
Distributed, L3
Filters the branch count information based on an IP address range specified for the
starting IP address <sip> and ending IP address parameters. You can specify up to four
different ranges of IP addresses to filter the command output.
Usage Guidelines
Use this command to view branch details for the distributed DHCP scopes.
Example
The following example shows the output of the show distributed-dhcp-branch-counts command:
Branch Count Table
-----------------Client Count Upto Branch Count
----------------- -----------1 10
2 4
3 3
7 1
The output of this command displays the following information:
Parameter
Description
Client Count Upto
Displays the number of clients allowed for each DHCP branch.
Branch Count
Displays the number of branches allowed for the specified range of IP
addresses.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
364 | show distributed-dhcp-branch-counts
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show distributed-dhcp-branch-counts | 365
show domain-names
show domain-names
Description
This command displays the list of enterprise-domains configured on a W-IAP.
Usage Guidelines
Use this command to view enterprise-domains list. The enterprise domains list displays the DNS domain names that
are valid on the enterprise network.
This list is used to determine how client DNS requests should be routed. When Content Filtering is enabled, the
DNS request of the clients is verified and the domain names that do not match the names in the list are sent to the
open DNS server.
Example
The following example shows the output of the show domain-names command:
example1.com
example.com
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
366 | show domain-names
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show dpi
show dpi {app <name> all|appcategory <name> all|debug statistics|qsessions [detail [<session_
id>]]|webcategory <name> all|webcategory-lookup <url>}
Description
This command displays the DPI configuration information.
Syntax
Command/Parameter
Description
app <name> <all>
Displays a list of all applications (with the all keyword) and details such
as application name, ID, application category, and default ports when a
specific application name is provided.
appcategory <name> <all>
Displays the list of all application categories (with the all keyword) and
details of the applications that belong to a specific application category
when an application category is specified.
debug statistics
Displays DPI statistics that can be used for debugging.
qsessions [detail [<session_
id>]
Displays advanced debug statistics for troubleshooting the DPI issues.
webcategory <name> <all>
Displays the list of web categories.
webcategory-lookup <URL>
Displays the details for a given URL and the reputation score based on
security rating. Run this command twice to fetch information from the
cloud server.
Usage Guidelines
Use this command to view the DPI configuration details.
Example
show dpi app
The following example shows the output of the show dpi app <name> command:
(Instant AP)# show dpi app wikipedia
Pre-defined Application
----------------------Name App ID App Category Default Ports
---- ------ ------------ ------------wikipedia 222 web tcp 80
The output of this command displays details such as the name of the application, application category, default ports
configured for deep packet inspection.
show dpi appcategory
The following example shows the output of the show dpi appcategory all command:
(Instant AP)# show dpi appcategory all
Pre-defined Application Categories
----------------------------------
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show dpi | 367
Name App Category ID
---- --------------antivirus 1
authentication 2
cloud-file-storage 3
collaboration 4
encrypted 5
enterprise-apps 6
gaming 7
im-file-transfer 8
instant-messaging 9
mail-protocols 10
mobile-app-store 11
network-service 12
peer-to-peer 13
social-networking 14
standard 15
streaming 16
thin-client 17
tunneling 18
unified-communications 19
web 20
webmail 21
Total application categories = 21
The output of this command displays all application categories.
show dpi debug statistics
The following example shows the output of the show dpi debug statistics command.
(Instant AP)# show dpi debug statistics
DPI Running :TRUE
Dpi Debug Statistics
--------------------Key Value
--- ----dpimgr total pkt handled 5507(55)
dpimgr total classified 975(6)
dpimgr qsession total alloc 417(2)
dpimgr qsession total uapp alloc 417(2)
dpimgr qsession total uapp alloc free 417(2)
dpimgr qsession total session age 417(3)
dpimgr qsession classified skipped 7(0)
dpimgr qsession event param error 20(0)
dpimgr qsession total classified 834(4)
dpimgr qsession total request received 424(2)
dpimgr bca total cloud lookup 22(2)
dpimgr bca total cached lookup 123(2)
dpimgr bca total request received 145(4)
dpimgr bca total classified 141(2)
DPI internal stats
number of cache hits :12
number of cloud hits :2
number of cloud lookups :2
number of local database hits :0
number of uncategorized responses :0
number of cache entries :20
maximum queue depth reached :0
trusted user rep average :90
guest user rep average :0
total number of lookup errors :0
current major version :0
368 | show dpi
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
current minor version :1
show dpi webcategory
The following example shows the output of the show dpi webcategory all command:
(Instant AP)# show dpi webcategory all
Pre-defined BrightCloud Web Categories
-------------------------------------Name Web Category ID
---- --------------real-estate 1
computer-and-internet-security 2
financial-services 3
business-and-economy 4
computer-and-internet-info 5
auctions 6
shopping 7
cult-and-occult 8
travel 9
abused-drugs 10
adult-and-pornography 11
home-and-garden 12
military 13
social-networking-web 14
dead-sites 15
individual-stock-advice-and-tools 16
training-and-tools 17
dating 18
sex-education 19
religion 20
entertainment-and-arts 21
personal-sites-and-blogs 22
legal 23
local-information 24
streaming-media 25
job-search 26
gambling 27
translation 28
reference-and-research 29
shareware-and-freeware 30
peer-to-peer-web 31
marijuana 32
hacking 33
games 34
philosophy-and-political-advocacy 35
weapons 36
pay-to-surf 37
hunting-and-fishing 38
society 39
educational-institutions 40
online-greeting-cards 41
sports 42
swimsuits-and-intimate-apparel 43
questionable 44
kids 45
hate-and-racism 46
personal-storage 47
violence 48
keyloggers-and-monitoring 49
search-engines 50
internet-portals 51
web-advertisements 52
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show dpi | 369
cheating 53
gross 54
web-based-email 55
malware-sites 56
phishing-and-other-frauds 57
proxy-avoidance-and-anonymizers 58
spyware-and-adware 59
music 60
government 61
nudity 62
news-and-media 63
illegal 64
content-delivery-networks 65
internet-communications 66
bot-nets 67
abortion 68
health-and-medicine 69
spam-urls 71
dynamically-generated-content 74
parked-domains 75
alcohol-and-tobacco 76
private-ip-addresses 77
image-and-video-search 78
fashion-and-beauty 79
recreation-and-hobbies 80
motor-vehicles 81
web-hosting 82
category-unknown 83
Total web categories = 80
The output of this command displays the list of web categories and the IDs associated with these categories.
show dpi webcategory-lookup
The following example shows the output of the show dpi webcategory-lookup <url> command:
(Instant AP)# show dpi webcategory-lookup www.yahoo.com
Input URL: www.yahoo.com
Request sent for CLOUD LOOKUP, please try again.
On running command again, the following information is retrieved from the cloud server and displayed as the output:
Input URL: www.yahoo.com
Found CACHED RESULT:
URL: yahoo.com REP: 81 A1: 0, Serial = 0x200001
Index: 0 Category: internet-portals(51) Confidence level: 98
Command History
Version
Description
Dell Networking W-Series
Instant 6.4.0.2-4.1
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
370 | show dpi
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show dpi-stats
show dpi-stats
app [id <app> |user ip <ip-addr>][full]
appcategory [id <appcat> |user ip <ip-addr>][full]
session [full]
webcategory [id <web> |user ip <ip-addr>][full]
webreputation [id <rep> |user ip <ip-addr>][full]
Description
This command displays the DPI statistics.
Syntax
Command/Parameter
Description
app
Displays application statistics.
appcategory
Displays the DPI statistics for application category.
session
Displays datapath session details for DPI.
webcategory
Displays the DPI statistics for web category.
webreputation
Displays the DPI statistics for web reputation score.
id
Displays DPI statistics for the specified application, application category,
web category or web reputation ID.
user ip <ip-addr>
Displays DPI statistics for specified user IP address.
full
Displays the complete DPI statistics for the application, application
category, session, web category, and web reputation stored on the WIAP since the last 15 minutes.
Usage Guidelines
Use this command to view the DPI statistics.
Example
show dpi-stats app
The following example shows the output of the show dpi-stats app full command:
Last snapshot timestamp 17:10:47
Dpi Top Application list
-----------------------App AppId Total bytes
--- ----- ----------apple 306 10172
apns 1118 278
Not-Classified 0 160
--------------------------Total bytes :10610
Classication percentage :98
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show dpi-stats | 371
show dpi-stats appcategory
The following example shows the output of the show dpi-stats appcategory full command:
Last snapshot timestamp 17:10:47
Dpi Top Application category list
--------------------------------App Category App Category Id Total bytes
------------ --------------- ----------web 20 10172
mobile-app-store 11 278
Not-Classified 0 160
--------------------------Total bytes :10610
Classication percentage :98
show dpi-stats session
The following example shows the output of the show dpi-stats session full command:
Datapath DPI CDR Session Table Entries
-------------------------------------Source IP App Webcat Webrep TX Bytes Rx Bytes
--------- --- ------ ------ -------- -------172.31.98.103 google-plus(1125) social-networking-web(14) trustworthy-sites(5) 8635 3697
172.31.98.103 krb5(97) Not-Classified(0) Not-Classified (0) 8237 5998
172.31.98.189 smb(185) Not-Classified(0) Not-Classified (0) 886 0
172.31.98.103 http(67) Not-Classified(0) Not-Classified (0) 507 4074
172.31.98.103 https(68) computer-and-internet-info(5) trustworthy-sites(5) 449597 644401
172.31.98.103 yahoo(1294) web-based-email(55) trustworthy-si tes(5) 6044 10818
172.31.98.103 gtalk(1441) Not-Classified(0) Not-Classified (0) 3375 5904
172.16.100.174 ssdp(197) Not-Classified(0) Not-Classified (0) 4339 0
Datapath DPI CDR Session Table Entries
-------------------------------------Source IP App Webcat Webrep TX Bytes Rx Bytes
--------- --- ------ ------ -------- -------10.17.139.167 ssdp(197) Not-Classified(0) Not-Classified (0) 6923 0
10.17.139.183 ssdp(197) Not-Classified(0) Not-Classified (0) 5458 0
172.16.100.174 udp(216) Not-Classified(0) Not-Classified (0) 152 0
10.17.139.167 windowslive(298) internet-portals(51) trustworthy-sites(5) 893 5907
172.31.98.103 http(67) computer-and-internet-info(5) trustworthy-sites(5) 439 1783
10.17.139.183 http(67) computer-and-internet-info(5) trustworthy-sites(5) 643 620
Num of Entries:47
show dpi-stats webcategory
The following example shows the output of the show dpi-stats webcategory full command:
Last snapshot timestamp 17:25:43
Dpi Top Web Category list
------------------------Web Category Web Category Id Total bytes
------------ --------------- ----------computer-and-internet-info 5 740
--------------------------Total bytes :740
show dpi-stats webreputation
The following example shows the output of the show dpi-stats webreputation full command:
Last snapshot timestamp 15:39:32
Dpi Top Web Reputation list
---------------------------
372 | show dpi-stats
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Web Reputation Web Reputation Id Total bytes
-------------- ----------------- ----------trustworthy-sites 5 1211900
moderate-risk-sites 3 2998
--------------------------Total bytes :1214898
Command History
Version
Description
Dell Networking W-Series
Instant 6.4.0.2-4.1
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show dpi-stats | 373
show election
show election {statistics}
Description
This command shows master W-IAP election statistics.
Syntax
Parameter
Description
statistics
Shows master election statistics.
Usage Guidelines
Use this command to view the statistics of the W-IAP selected as Virtual Controller.
Example
The following example shows the output of show election statistics command:
State : Master
master_beacon : sent=8162 rcvd=0
hierarchy_beacon: sent=7685 rcvd=0
hierarchy_ack : sent=0 rcvd=0
beacon_req : sent=0 rcvd=0
Slave->Pot-Master : 0 time
Pot-master->Master: 0 time
Pot-master->Slave : 0 time
spoof arp rcvd: 0
last spoof mac: 00:00:00:00:00:00
The output of this command includes the following information:
Parameter
Description
State
Indicates if the W-IAP is provisioned as master.
master_beacon
Displays the number of beacons transmitted and received by the master W-IAP.
hierarchy_beacon
Displays the number of beacons transmitted and received.
hierarchy_ack
Displays the number of beacons transmitted and received.
beacon_req
Displays the number of beacons required.
spoof arp rcvd
Displays the number of ARP spoof attacks detected.
last spoof mac
Displays the MAC address of the last spoof detected.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
374 | show election
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show election | 375
show external-captive-portal
show external-captive-portal [<name>]
Description
This command displays the external captive portal configuration details.
Syntax
Parameter
Description
name
Filters the output based on an existing external captive portal profile.
Usage Guidelines
Use this command to view information about the external captive portal server configuration details.
Example
The following output is displayed for the show external-captive-portal command:
External Captive Portal
----------------------Name Server Port Url Auth Text Redirect Url Server Fail Through Disable Auto
---- ------ ---- --- --------- ------------ ------------------- ------------default localhost 80 / Authenticated Disable Enable
Whitelist Use HTTPs In Use Redirect Mode
--------- --------- ------ ------------No Yes No
The output of this command displays details such as the external captive portal profile name, server name, server
port, redirection URL, and automatic whitelisting status.
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.1-4.0
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
376 | show external-captive-portal
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show fault
show fault [history]
Description
This command displays the list of active faults that occur in the event of a system fault and the faults that were
cleared from the system.
Syntax
Parameter
Description
history
Displays the list of faults that were cleared.
Usage Guidelines
Use this command to view the active faults for a W-IAP. Active faults are generated due to system faults.
Example
The following example shows the output for the show fault command:
Active Faults
------------Time Number Description
---- ------ ----------Total number of entries in the queue :0
The following example shows the output for the show fault history command:
Cleared Faults
-------------Time Number Cleared By Description
---- ------ ---------- ----------Total number of entries in the queue :0
The output of these commands provide the following information:
Parameter
Description
Timestamp
Displays the system time at which an event occurs.
Number
Indicates the sequence
Cleared By
Displays the module which cleared this fault.
Description
Provides a short description of the event details.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show fault | 377
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
378 | show fault
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ids
show ids {ap <mac>| aps| client <mac>|clients| phy-types| rap-types}
Description
This command displays the list of unknown APs and clients detected by the W-IAP with the IDS feature enabled.
Syntax
Parameter
Description
ap <mac>
Displays the signal details for the W-IAP.
aps
Displays the unknown Access Points detected by the W-IAP.
client <mac>
Displays the details of the W-IAP to which the client is connected.
clients
Displays the list of unknown clients detected by the W-IAP.
phy-types
Displays the PHY details of the W-IAP.
rap-types
Displays the list of Remote APs (W-IAPs) detected by the W-IAP.
Usage Guidelines
Use this command to view the intrusion detection details.
Examples
The following output is displayed for the show ids aps command:
Unknown Access Points Detected
-----------------------------MAC Address Network Classification Chan. Type Last Seen
----------- ------- -------------- ----- ---- --------6c:f3:7f:56:6d:01 NTT-SPOT Interfering 1 G 17:32:19
6c:f3:7f:56:67:41 NTT-SPOT Interfering 1 G 17:37:49
00:24:6c:2a:78:d2 edward-suiteb-178 Interfering 11 GN 20MZ 17:37:19
6c:f3:7f:94:63:30 avyas_vap1 Interfering 6 G 17:40:20
6c:f3:7f:94:63:02 avyas_vap2 Interfering 6 G 17:40:20
00:24:6c:2a:7d:0b edward-suiteb Interfering 149 AN 40MZ 17:39:19
6c:f3:7f:a5:df:34 sw-san-rapng-nat Interfering 153 AN 20MZ 17:38:49
6c:f3:7f:56:7d:00 7SPOT Interfering 1 GN 20MZ 17:32:19
00:24:6c:80:8e:82 instant Interfering 11 GN 20MZ 17:29:48
00:1a:1e:40:06:00 test123 Interfering 11 G 17:37:49
00:24:6c:2a:78:d3 ssid_edward_psk_178 Interfering 11 GN 20MZ 17:37:49
6c:f3:7f:94:63:31 avyas_vap2 Interfering 6 G 17:40:20
6c:f3:7f:b5:bd:22 iClarice2 Interfering 6 GN 20MZ 17:39:19
6c:f3:7f:94:63:03 avyas_vap1 Interfering 6 G 17:40:20
00:24:6c:2a:7d:0c edward_tls2k Interfering 149 AN 40MZ 17:39:19
6c:f3:7f:a5:df:35 sw-san-native Interfering 153 AN 20MZ 17:38:49
00:24:6c:80:4f:88 ethersphere-wpa2 Interfering 52 AN 40MZ 17:40:20
The show ids aps command output provides information on the MAC address of interfering W-IAPs, the network to
which the unknown W-IAPs are connected, the interference classification, channels on which the unknown APs are
detected, the radio configuration type and recent timestamp of the interference.
The following output is displayed for the show ids clients command:
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ids | 379
Unknown Clients Detected
-----------------------MAC Address Network Classification Chan. Type Last Seen
----------- ------- -------------- ----- ---- --------00:26:c6:4d:2b:74 ethersphere-wpa2 Interfering 1 GN 20MZ 17:26:48
00:24:d7:40:a8:64 akvoice1 Interfering 6 G 17:38:49
00:24:d7:40:ca:88 akvoice1 Interfering 6 G 17:39:50
74:e5:43:4b:3b:ff manju34-vap1 Interfering 44 AN 40MZ 17:39:50
The show ids clients command output provides information on the MAC address of interfering clients, the network
to which the unknown clients are connected, the interference classification, channels on which the unknown clients
are detected, the radio configuration type and recent timestamp of the interference.
The following output is displayed for the show ids phy-types command:
Physical Types
-------------Keyword Value
------- ----b 0
a 1
g 2
ag 3
The following output is displayed for the show ids rap-types command:
RAP Types
--------Keyword Value
------- ----valid 0
interfering 1
rogue 2
dos-attack 3
unknown 4
known-interfering 5
suspect-rogue 6
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
380 | show ids
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ids-detection config
show ids-detection config
Description
This command displays the list of intrusion detection policies configured on a W-IAP.
Usage Guidelines
Use this command to view a list of intrusion detection policies enabled for a W-IAP.
Example
The following output is displayed for the show ids-detection command:
infrastructure detection level :off
--------------------------------------------------Policies Status Low Medium High
-------- ------ --- ------ ---detect-ap-spoofing disable enable enable enable
detect-windows-bridge disable enable enable enable
signature-deauth-broadcast disable enable enable enable
signature-deassociation-broadcast disable enable enable enable
detect-adhoc-using-valid-ssid enable disable enable enable
detect-malformed-large-duration enable disable enable enable
detect-ap-impersonation enable disable disable enable
detect-adhoc-network enable disable disable enable
detect-valid-ssid-misuse enable disable disable enable
detect-wireless-bridge disable disable disable enable
detect-ht-40mhz-intolerance disable disable disable enable
detect-ht-greenfield disable disable disable enable
detect-ap-flood disable disable disable enable
detect-client-flood disable disable disable enable
detect-bad-wep disable disable disable enable
detect-cts-rate-anomaly disable disable disable enable
detect-rts-rate-anomaly disable disable disable enable
detect-invalid-addresscombination disable disable disable enable
detect-malformed-htie disable disable disable enable
detect-malformed-assoc-req disable disable disable enable
detect-malformed-frame-auth disable disable disable enable
detect-overflow-ie disable disable disable enable
detect-overflow-eapol-key disable disable disable enable
detect-beacon-wrong-channel disable disable disable enable
detect-invalid-mac-oui disable disable disable enable
client detection level :off
--------------------------------------------------Policies Status Low Medium High
-------- ------ --- ------ ---detect-valid-clientmisassociation disable enable enable enable
detect-disconnect-sta disable disable enable enable
detect-omerta-attack disable disable enable enable
detect-fatajack disable disable enable enable
detect-block-ack-attack disable disable enable enable
detect-hotspotter-attack disable disable enable enable
detect-unencrypted-valid disable disable enable enable
detect-power-save-dos-attack disable disable enable enable
detect-eap-rate-anomaly disable disable disable enable
detect-rate-anomalies disable disable disable enable
detect-chopchop-attack disable disable disable enable
detect-tkip-replay-attack disable disable disable enable
signature-airjack disable disable disable enable
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ids-detection config | 381
signature-asleap disable disable disable enable
The output for this command provides the following information:
Parameter
Description
Infrastructure
detection level
Indicates if the detection level for the policies is set to off, low, medium, or high.
Policies
Displays the list of intrusion detection policies.
Status
Indicates if a policy is enabled or disabled.
Low
Indicates if the detection level for a policy is set to low.
Medium
Indicates if the detection level for a policy is set to medium.
High
Indicates if the detection level for a policy is set to high.
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
382 | show ids-detection config
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ids-protection config
show ids-protection config
Description
This command displays the list of infrastructure protection policies for a W-IAP.
Usage Guidelines
Use this command to view the status of infrastructure protection policies on a W-IAP.
Examples
The following output is displayed for the show ids-protection config command:
Wireless Containment :none
Wired Containment :off
infrastructure protection level :off
--------------------------------------------------Policies Status Low High
-------- ------ --- ---protect-ssid disable enable enable
rogue-containment disable enable enable
protect-adhoc-network disable disable enable
protect-ap-impersonation disable disable enable
client protection level :off
--------------------------------------------------Policies Status Low High
-------- ------ --- ---protect-valid-sta disable enable enable
protect-windows-bridge disable disable enable
Parameter
Description
Infrastructure
protection level
Indicates if the protection level for the policies is set to off, low, medium, or high.
Policies
Displays the list of wired and wireless network infrastructure protection policies.
Status
Indicates if a policy is enabled or disabled.
Low
Indicates if the protection level for a policy is set to low.
Medium
Indicates if the protection level for a policy is set to medium.
High
Indicates if the protection level for a policy is set to high.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ids-protection config | 383
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
384 | show ids-protection config
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show image
show image version
Description
This command displays the Instant software version running on a W-IAP.
Example
The following example shows the output of show image version command:
Primary Partition Build Time :2013-03-31 11:47:06 PDT
Primary Partition Build Version :6.2.1.0-3.3.0.0_37845
AP Images Classes
----------------Class
----Cassiopeia
Parameter
Description
Primary Partition Build
Time
Shows the W-IAP image build time.
Primary Partition Build
Version
Shows the W-IAP build version.
AP Image Class
Indicates the W-IAP class. The following examples describe the image class
for different W-IAP models:
l For W-IAP135/134 —DellInstant_Cassiopeia_<build-version>
l For W-IAP108/109 —DellInstant_Pegasus_<build-version>
l For W-IAP155/155P—DellInstant_Aries_<build-version>
l For all other W-IAPs —DellInstant_Orion_<build-version>
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show image | 385
show interface counters
show interface counters
Description
This command shows the Ethernet interface packet counters for the W-IAP.
Usage Guidelines
Use this command to view table of L2 interface counters.
Example
The following example shows the partial output of show interface counters command:
bond0 is up, line protocol is up
Hardware is Gigabit Ethernet, address is d8:c7:c8:c4:42:98
Speed 1000Mb/s, duplex full
Received packets 9441
Received bytes 1134064
Receive dropped 0
Receive errors 0
Receive missed errors 0
Receive overrun errors 0
Receive frame errors 0
Receive CRC errors 0
Receive length errors 0
Transmitted packets 16435
Transmitted bytes 841278
Transmitted dropped 0
Transmission errors 0
Lost carrier 0
Parameter
Description
Speed
Shows speed of the Ethernet interface.
Received packets
Shows total number of received packets.
Received bytes
Shows the total number of received bytes.
Receive dropped
Shows total number of packets dropped.
Receive errors
Shows total number of errors during packet receive.
Receive missed errors
Shows total number of errors missed during packet receive.
Receive overrun errors
Shows total number of received overrun errors.
Receive frame errors
Shows total number of frame errors during packet receive.
Receive CRC errors
Shows total number of CRC errors during packet receive.
Receive length errors
Shows total length of the error.
Transmitted packets
Shows total number of transmitted packets.
Transmitted bytes
Shows total number of transmitted bytes.
386 | show interface counters
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Parameter
Description
Transmitted dropped
Shows total number of packets dropped.
Transmission errors
Shows total number of errors during packet transmit.
Lost carrier
Shows total number of lost carriers.
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.4
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show interface counters | 387
show inbound-firewall-rules
show inbound-firewall-rules
Description
This command displays the details of inbound firewall rules configured on a W-IAP.
Usage Guidelines
Use this command to view the details of the inbound firewall rules configured for a W-IAP network.
Example
The following output is displayed for the show inbound-firewall-rules command:
Access Rules
-----------Src IP Src Mask Dest IP Dest Mask Dest Match Protocol (id:sport:eport) Application Action Log
TOS 802.1P Blacklist App Throttle (Up:Down) Mirror DisScan ClassifyMedia
------ -------- ------- --------- ---------- ------------------------- ----------- ------ ----- ------ --------- ---------------------- ------ ------- ------------any any any any match h323-tcp permit
any any 192.0.2.0 255.255.255.0 match h323-udp permit
The output of this command displays information about the inbound firewall access rule configuration parameters,
which indicate whether a particular type of traffic is to allowed to a particular destination from the source subnet, and
the service and protocol in use. It also indicates if other options such as logging and prioritizing traffic are enabled
when the rule is triggered.
Command History
Version
Description
Dell Networking W-Series Instant
6.4.0.2-4.1
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
388 | show inbound-firewall-rules
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ip dhcp database
show ip dhcp database
Description
This command displays the DHCP server settings.
Usage Guidelines
Use this command to the DHCP server settings. The DHCP server is a built-in server, used for networks in which
clients are assigned IP address by the Virtual Controller.
Example
The following output is displayed for the show ip dhcp database command:
DHCP
DHCP
DHCP
DHCP
DHCP
Subnet :192.0.2.0
Netmask :255.255.255.0
Domain Name :example.com
DNS Server :192.0.2.1
DNS Cache :Disabled
The output of this command provides the following information:
Column
Description
DHCP subnet
Indicates the network range for the client IP addresses.
DHCP Netmask
Indicates the subnet mask specified for the IP address range for the DHCP subnet.
DHCP Lease Time(m)
Indicates the duration of DHCP lease. The lease time refers to the duration of
lease that a DHCP-enabled client has obtained for an IP address from a DHCP
server.
DHCP Domain Name
Indicates the domain-name of the DHCP client.
DHCP DNS Server
Indicates the IP address of the DNS server.
DHCP DNS Cache
Indicates if the DNS cache is enabled.
Command History
Version
Description
Dell Networking W-Series Instant
6.4.0.2-4.1
The output of this command was modified.
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ip dhcp database | 389
show ip igmp
show ip igmp group [maddr <multicast-addr>]
Description
This command displays information about the Internet Group Management Protocol (IGMP) group table.
Syntax
Parameter
Description
maddr <multicast-addr>
Filters group table information based on the multicast IP address.
Usage Guidelines
Use this command to view the IGMP group table information for a W-IAP.
Example
The following output is displayed for the show ip igmp group command:
IGMP Group Table
---------------Group Members vlan
239.255.255.250 1 333
224.0.0.251 1 333
224.0.0.252 1 333
The following output is displayed for the show ip igmp group maddr <multicast-addr> command:
IGMP Group 224.0.0.251 Table
-------------------------------Member Mac Vlan Destination Age
------ --- ---- ----------- --10.17.88.226 08:ed:b9:e1:51:7d 333 aruba002 15
The output of this command includes the following parameters:
Parameter
Description
IGMP Group
Table
Displays details for the IGMP multicast group.
Group
Indicates the IP addresses for the multicast group.
Members
Indicates the number of members assigned to the multicast group.
VLAN
Indicates the VLAN ID associated with the multicast group.
IGMP Group
<multicastaddress>
Table
Displays the IGMP details specific to a multicast address.
Member
Indicates the IP address of the member associated with the specified multicast group address.
MAC
Indicates the MAC address of member associated with the specified multicast group address.
390 | show ip igmp
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Parameter
Description
VLAN
Indicates the VLAN ID associated with the multicast groups or a specific multicast group
address.
Destination
Indicates the destination to which the multicast packets are routed.
Age
Indicates the aging time of the forwarding table entries.
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ip igmp | 391
show ip interface brief
show ip interface brief
Description
This command displays a summary of IP related information for all interfaces configured on a W-IAP.
Usage Guidelines
Use this command to view a brief summary of IP related information for the W-IAP interfaces.
Example
The following output is displayed for the show ip interface brief command:
Interface IP Address / IP Netmask Admin Protocol
br0 10.17.88.188 / 255.255.255.192 up up
The output of this command provides the following information:
Column
Description
Interface
Lists the interface and interface identification, where applicable.
IP Address /IP Netmask
Lists the IP address and subnet mask for the interface.
Admin
Displays the administrative status of the interface.
l Enabled—up
l Disabled—down
Protocol
Displays the status of the IP on the interface.
l Enabled—up
l Disabled—down
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
392 | show ip interface brief
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ip route
show ip route
Description
This command displays the W-IAP routing table.
Usage Guidelines
Use this command to view the IP routes configured for a W-IAP.
Examples
The following output shows the ip address of routers and the VLANs to which they are connected.
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
172.16.10.1 0.0.0.0 255.255.255.255 UH 0 0 0 tun0
10.17.88.128 0.0.0.0 255.255.255.192 U 0 0 0 br0
2.2.2.0 0.0.0.0 255.255.255.0 U 0 0 0 br0
192.168.10.0 0.0.0.0 255.255.254.0 U 0 0 0 br0
0.0.0.0 10.17.88.129 0.0.0.0 UG 0 0 0 br0
The output of this command provides the following information:
Column
Description
Destination
Displays the destination IP address for the IP routes.
Gateway
Displays the gateway IP address for the IP routes.
Genmask
Displays the subnet mask details for the IP routes.
Flags
Indicates if the route is up (U), targeted to the host (UH), or if it uses Gateway (UG).
MSS
Indicates the default maximum segment size for TCP connections over this route.
Window
Indicates the default window size for TCP connections over this route.
irrt
Indicates the initial RTT (Round Trip Time). The kernel uses this to determine the
best TCP protocol parameters instead of relying on slow responses.
Iface
Indicates the Interface to which packets are routed.
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ip route | 393
show lacp status
show lacp status
Description
This command displays the Link Aggregation Control Protocol (LACP) configuration status on a W-IAP.
Usage Guidelines
Use this command to view the LACP status on W-IAP220 Series devices. LACP provides a standardized means for
exchanging information with partner systems to form a dynamic link aggregation group. The LACP feature is
automatically enabled during W-IAP boots and it dynamically detects the AP if connected to a partner system with
LACP capability, by checking if there is any LACP Protocol Data Unit (PDU) received on either eth0 or eth1 port.
Example
The following example shows the output of the show lacp status command:
AP LACP Status
-------------Link Status LACP Rate Num Ports Actor Key Partner Key Partner MAC
----------- --------- --------- --------- ----------- ----------Up slow 2 17 1 70:81:05:11:3e:80
Slave Interface Status
---------------------Slave I/f Name Permanent MAC Addr Link Status Member of LAG Link Fail Count
-------------- ------------------ ----------- ------------- --------------eth0 6c:f3:7f:c6:76:6e Up Yes 0
eth1 6c:f3:7f:c6:76:6f Up Yes 0
Traffic Sent on Enet Ports
-------------------------Radio Num Enet 0 Tx Count Enet 1 Tx Count
--------- --------------- --------------0 0 0
1 0 0
non-wifi 2 17
The output of this command displays details such as the link status, number of ports, AP partner MAC address, and
the interface status.
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.1-4.0
This command is introduced.
Command Information
W-IAP Platform
Command Mode
W-IAP220 Series
Privileged EXEC mode
394 | show lacp status
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show l2tpv3 config
show l2tpv3 config
Description
This command displays the L2TPV3 session and tunnel configuration details.
Usage Guidelines
Use this command to view the tunnel and session configuration details.
Example
The following example shows the output of the show l2tpv3 config command:
(Instant AP)# show l2tpv3 config
L2TPV3 Tunnel configuration
--------------------------Tunnel Profile Primary Peer Backup Peer Peer UDP Port Local UDP Port Hello Interval Host Name
MTU Message Digest Type secret Key Failover Mode Failover Retry Count Retry Interval Checksum
-------------- ------------- ------------ ------------- -------------- -------------- -------- --- ------------------- ---------- ------------- -------------------- -------------- ------test_tunnel 10.0.0.63 10.0.0.65 3000 1701 150 Instant-C4:42:98 1570 MD5
625beed39fa4ff3424edb3082ede48fa non-preemptive 5 80 Disabled
L2TPV3 Session configuration
---------------------------Session Name Tunnel Name Local tunnel IP Tunnel Mask Tunnel Vlan Session Cookie Length Session
Cookie Session Remote End ID
------------ ----------- --------------- ----------- ----------- --------------------- ------------- --------------------test_session 1.1.1.1 255.255.255.0 5 0 0 0
The output of this command includes the following information:
Parameter
Description
Tunnel Profile
Displays the tunnel profile name.
Primary Peer
Displays the IP address of the remote end tunnel.
Backup Peer
Displays the IP address of the remote end backup tunnel.
Peer UDP Port
Displays the UDP port number of the remote end backup tunnel.
Local UDP Port
Displays the UDP port number of the remote end tunnel.
Hello Interval
Displays the interval (in seconds) at which hello packets are routed in the tunnel.
Host Name
Displays the name of the W-IAP.
MTU
Displays the value for the tunnel MTU.
Message Digest Type
Displays the message digest to be used to create the MD AVP.
secret Key
Displays the shared key used for message digest.
Failover Mode
Displays the backup/primary tunnel failover mode.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show l2tpv3 config | 395
Parameter
Description
Failover Retry Count
Displays the number of failover attempts.
Retry Interval
Displays the interval between each failover.
Checksum
Displays the end-to-end checksum of packets that pass through the tunnel.
Session Name
Displays the session profile name.
Tunnel Name
Displays the tunnel profile name.
Local tunnel IP
Displays the IP address of the remote end tunnel.
Tunnel Mask
Displays the network mask of the tunnel.
Tunnel Vlan
Displays the VLAN number to be carried in this tunnel session.
Session Cookie Length
Displays the cookie length for the cookie.
Session Cookie
Displays the cookie value.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.4
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
396 | show l2tpv3 config
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show l2tpv3 global
show l2tpv3 global parameter
Description
This command displays L2TPv3 global configuration details such as hostname.
Usage Guidelines
Use this command to view the hostname configured.
Example
The following example shows the output of the show l2tpv3 global parameter command:
L2TPV3 Global configuration
--------------------------Host Name
---------Instant-C4:42:98
The output of this command includes the following information:
Parameter
Description
Host Name
Displays the W-IAP name.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.4
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show l2tpv3 global | 397
show l2tpv3 session
show l2tpv3 session status
Description
This command displays the L2TP session connectivity status.
Usage Guidelines
Use this command to view the session connectivity status.
Example
The following example shows the output of the show l2tpv3 session status command:
Session 1821009927 on tunnel 858508253:type: LAC Incoming Call, state: ESTABLISHED
created at: Jul 2 04:58:45 2013
administrative name: 'test_session' (primary)
created by admin: YES, peer session id: 12382
session profile name: test_session_primary
data sequencing required: OFF
use data sequence numbers: OFF
Peer configuration data:data sequencing required: OFF
framing types:
data rx packets: 16, rx bytes: 1560, rx errors: 0 rx cookie error 0
data tx packets: 6, tx bytes: 588, tx errors: 0
The output of this command shows the session connectivity status, tunnel creation time. configuration data, data
frame types and so on.
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.4
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
398 | show l2tpv3 session
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show l2tpv3 system
show l2tpv3 system statistics
Description
This command displays the L2TPV3 system statistics details.
Usage Guidelines
Use this command to view the tunnel and session statistics.
Example
The following example shows the output of the show l2tpv3 system statistics command:
(Instant AP)# sh l2tpv3 system statistics
L2TP counters:Total messages sent: 99, received: 194, retransmitted: 0
illegal: 0, unsupported: 0, ignored AVPs: 0, vendor AVPs: 0
Setup failures: tunnels: 0, sessions: 0
Resource failures: control frames: 0, peers: 0
tunnels: 0, sessions: 0
Limit exceeded errors: tunnels: 0, sessions: 0
Frame errors: short frames: 0, wrong version frames: 0
unexpected data frames: 0, bad frames: 0
Internal: authentication failures: 0, message encode failures: 0
no matching tunnel discards: 0, mismatched tunnel ids: 0
no matching session_discards: 0, mismatched session ids: 0
total control frame send failures: 0, event queue fulls: 0
Message counters:Message RX Good RX Bad TX
ILLEGAL 0 0 0
SCCRQ 0 0 1
SCCRP 1 0 0
SCCCN 0 0 1
STOPCCN 0 0 0
RESERVED1 0 0 0
HELLO 95 0 95
OCRQ 0 0 0
OCRP 0 0 0
OCCN 0 0 0
ICRQ 0 0 1
ICRP 1 0 0
ICCN 0 0 1
RESERVED2 0 0 0
CDN 0 0 0
WEN 0 0 0
SLI 0 0 0
The output of this command shows the system statistics such as total number of messages sent or received, type of
message, and so on.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.4
This command is introduced.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show l2tpv3 system | 399
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
400 | show l2tpv3 system
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show l2tpv3 tunnel
show l2tpv3 tunnel {config | status}
Description
This command displays the L2TP tunnel status and configuration details.
Usage Guidelines
Use this command to view the tunnel connectivity status and configuration details.
Example
The following example shows the output of the show l2tpv3 tunnel config command:
Tunnel profile test_tunnel_primary
l2tp host name: aruba1600pop658509.hsb-dev4.aus
local UDP port: 1701
peer IP address: 10.13.11.157
peer UDP port: 1701
hello timeout 60, retry timeout 1, idle timeout 0
rx window size 10, tx window size 10, max retries 5
use UDP checksums: OFF
do pmtu discovery: OFF, mtu: 1460
framing capability: SYNC ASYNC
bearer capability: DIGITAL ANALOG
use tiebreaker: OFF
peer profile: NOT SET
session profile: NOT SET
trace flags: PROTOCOL FSM API AVPDATA FUNC XPRT DATA SYSTEM CLI
Tunnel profile test_tunnel_backup
l2tp host name: aruba1600pop658509.hsb-dev4.aus
local UDP port: 1701
peer IP address: 10.13.11.157
peer UDP port: 1701
hello timeout 60, retry timeout 1, idle timeout 0
rx window size 10, tx window size 10, max retries 5
use UDP checksums: OFF
do pmtu discovery: OFF, mtu: 1460
framing capability: SYNC ASYNC
bearer capability: DIGITAL ANALOG
use tiebreaker: OFF
peer profile: NOT SET
session profile: NOT SET
trace flags: PROTOCOL FSM API AVPDATA FUNC XPRT DATA SYSTEM CLI
The output of this command shows the tunnel profile name, L2TP hostname, local UDP port number, hello packets
interval, and so on.
The following example shows the output of the show l2tpv3 tunnel status command:
Tunnel 858508253, from 10.13.11.29 to 10.13.11.157:state: ESTABLISHED
created at: Jul 2 04:58:25 2013
administrative name: 'test_tunnel' (primary)
created by admin: YES, tunnel mode: LAC, persist: YES
local host name: Instant-C4:42:98
peer tunnel id: 1842732147, host name: aruba1600pop636635.hsbtst2.aus
UDP ports: local 1701, peer 3000
session limit: 0, session count: 1
tunnel profile: test_tunnel_primary, peer profile: default
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show l2tpv3 tunnel | 401
session profile: default
hello timeout: 150, retry timeout: 80, idle timeout: 0
rx window size: 10, tx window size: 10, max retries: 5
use udp checksums: OFF
do pmtu discovery: OFF, mtu: 1460
trace flags: PROTOCOL FSM API AVPDATA FUNC XPRT DATA SYSTEM CLI
peer vendor name: Katalix Systems Ltd. Linux-2.6.32-358.2.1.el6.x86_64 (x86_64)
peer protocol version: 1.0, firmware 0
peer rx window size: 10
Transport status:ns/nr: 98/97, peer 98/96
cwnd: 10, ssthresh: 10, congpkt_acc: 9
Transport statistics:out-of-sequence control/data discards: 0/0
ACKs tx/txfail/rx: 0/0/96
retransmits: 0, duplicate pkt discards: 0, data pkt discards: 0
hellos tx/txfail/rx: 94/0/95
control rx packets: 193, rx bytes: 8506
control tx packets: 195, tx bytes: 8625
data rx packets: 0, rx bytes: 0, rx errors: 0
data tx packets: 6, tx bytes: 588, tx errors: 0
establish retries: 0
The output of this command shows the tunnel profile name, tunnel creation date, hello packets sent or received, and
so on.
Command History
Version
Description
Dell Networking W-Series
Instant 6.4.0.2-4.1
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
402 | show l2tpv3 tunnel
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show l3-mobility
show l3-mobility {config| datapath| events [<count> <mac>]| status}
Description
This command displays details about the Layer-3 (L3) events, mobility configuration, and roaming status of the WIAP clients.
Syntax
Parameter
Description
config
Displays the L3 mobility configuration details for a W-IAP.
datapath
Displays the datapath statistics associated with L3 mobility.
events [<count> <mac>]
Displays L3 mobility events for all W-IAP clients or individual clients
filtered based on MAC address.
status
Displays the L3 mobility status for a W-IAP.
Usage Guidelines
Use this command to view the L3 mobility information for a W-IAP.
Examples
show l3-mobility config
The following example shows the output of the show l3-mobility config command:
Flags
----Type Value
---- ----Home Agent Load Balancing enable
Virtual Controller Table
-----------------------Virtual Controller IP
--------------------192.0.1.0
Subnet Table
-----------Subnet Netmask VLAN Virtual Controller
------ ------- ---- -----------------192.0.2.0 255.255.255.255 2 192.0.1.0
The output of this command provides the following information:
Column
Description
Flags
Indicates if any L3 mobility features are enabled.
Type
Indicates the type of the flag.
Value
Indicates if a flag is enabled.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show l3-mobility | 403
Column
Description
Virtual Controller IP
Displays the Virtual Controller IP address. The Virtual Controller IP
configuration for each W-IAP allows the clients to roam seamlessly among all
the W-IAPs.
Subnet
Indicates the IP address for the mobility domain.
Netmask
Displays the subnet mask configuration details.
VLAN
Displays the VLAN ID configured for the mobility domain.
Virtual Controller
Displays the Virtual Controller configuration associated with the mobility
domain.
show l3-mobility datapath
The following example shows the output of show l3-mobility datapath command:
L3 Mobility Datapath Home Table
------------------------------Client Index Client MAC Home Vlan Destinaton Device Index
------------ ---------- --------- ----------------------L3 Mobility Datapath Foreign Table
---------------------------------Client Index Client MAC Home Vlan VAP Vlan Destinaton Device Index HAP IP Virtual Controller
IP Packets Forwarded
-------------- ----------------L3 Mobility Datapath Tunnel Table
--------------------------------Tunnel Device Remote Protocol Dest IP Clients Idle Time Rx Packets Tx Packets Rx Mcasts Tx
Mcasts ARP Proxy Pkts Tx Jumbo MTU Rx HB Tx HB MTU Reqs MTU Resps HB Mismatch IP Mismatch Type
Vlan Translations
------------- --------------- ------- ------- --------- ---------- ---------- --------- -------- -------------- -------- --- ----- ----- -------- --------- ----------- ----------- ---- ----------------
The output of this command provides the following information:
Parameter
Description
L3 Mobility
Datapath Home
Table
Displays details such as client index, client MAC address, VLAN, destination device
associated with the L3 mobility home subnet.
L3 Mobility
Datapath Foreign
Table
Displays details such as client index, client MAC address, VLAN, Destination device,
home AP IP address, Virtual Controller IP address and packet details associated
with the L3 mobility foreign subnet.
L3 Mobility
Datapath Tunnel
table
Displays the following details about L3 mobility tunnel:
l
l
l
l
l
l
l
l
l
404 | show l3-mobility
Tunnel - Indicates the tunnel interface.
Device - Displays the device ID.
Remote Protocol - Indicates the remote protocol used by the roaming clients.
Dest IP - Indicates the destination IP address to which the packets are routed.
Clients - Displays the list of clients
Idle Time - Displays the idle time
Rx Packets - Displays information about packets received.
Tx Packets - Displays information about packets transmitted.
Rx Mcasts - Displays information about multicast packets received.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Parameter
Description
l
l
l
l
l
l
l
l
l
l
l
Tx Mcasts - Displays information about multicast packets transmitted.
ARP Proxy Pkts - Displays information packets resolved to destination IP address
by the proxy Address Resolution Protocol (ARP)
Tx Jumbo MTU - Displays information about the Maximum Transmission Unit
(MTU) in jumbo frames.
Rx HB
Tx HB
MTU Reqs - Indicates the number of MTU requests sent.
MTU Resps - Indicates the number of MTU responses received.
HB Mismatch
IP Mismatch - Indicates IP address mismatch if any
Type
Vlan Translations - Displays details about VLAN translation.
show l3-mobility events
The following example shows the output of the show l3-mobility events command:
L3 Mobility Events
-----------------Time Client MAC Event IP Dir
---- ---------- ----- -- ---- May 9 23:26:29 08:ed:b9:e1:51:87 Station Offline 10.17.88.59 <May 9 23:26:29 08:ed:b9:e1:51:87 Potential Foreign Client10.17.88.59 <May 9 23:09:05 08:ed:b9:e1:51:87 This Client is Normal 10.17.88.59 ->
Peer
---self
self
self
IP Home Vlan VAP Vlan Tunnel ID Old AP IP FAP IP HAP IP VC IP Additional Info
---------- -------- ------- --------- -------- ----- ---- --------- 1 - - - - - - - - - - - - - 1 - - 10.17.88.59 - l2-timed-out,test
The output of this command provides the following information:
Parameter
Description
Time
Indicates the timestamp of the L3 mobility event.
Client MAC
Indicates the MAC address of the roaming clients.
Event
Provides a description of the mobility event.
IP
Indicates the IP address of the roaming client.
Dir
Indicates if the client has roamed in or out of the mobility subnet.
Peer IP
Displays the peer IP address, if any peer clients are configured.
Home Vlan
Displays the VLAN ID associated with the home subnet.
VAP Vlan
Displays the VLAN ID associated with the Virtual AP.
Tunnel ID
Indicates the tunnel interface used for routing packets.
Old AP IP
Indicates the IP address of the W-IAP from which the client has roamed.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show l3-mobility | 405
Parameter
Description
FAP IP
Indicates the IP address of the W-IAP in the foreign subnet.
HAP IP
Indicates the IP address of the W-IAP in the home subnet, to which the client is
currently connected.
VC IP
Indicates the IP address of the Virtual Controller.
Additional Info
Displays additional information if any.
show l3-mobility status
The following example shows the output of the show l3-mobility status command:
Roaming Client Table
-------------------Client MAC Home Vlan VAP Vlan Tunnel ID Status Virtual Controller IP Peer IP Old AP IP Device
Name
---------- --------- -------- --------- ------ --------------------- ------- --------- ---------Tunnel Table
-----------Peer IP Local Tunnel ID Remote Tunnel ID Use Count Type
------- --------------- ---------------- --------- ---Virtual Controller Table
-----------------------Virtual Controller IP Type HAP IP Local Tunnel ID Remote Tunnel ID
--------------------- ---- ------ --------------- ---------------192.0.1.0 C - - -
The output of this command provides the following information:
Parameter
Description
Roaming Client
Table
Displays details such as client MAC address, Home AP and Virtual AP VLAN, Tunnel
ID, roaming status, Virtual Controller IP address, peer IP address, old IP address,
and the name of the device.
Tunnel Table
Displays details such as peer IP address, local tunnel ID. remote tunnel ID, tunnel
count, and the type of tunnel used for routing packets.
Virtual Controller
Table
Displays details such as Virtual Controller IP address, type, Home AP IP address,
local tunnel ID, and remote tunnel ID.
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
406 | show l3-mobility
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ldap-servers
show radius-servers
Description
This command displays the Lightweight Directory Access Protocol (LDAP) servers configured for user
authentication on the Virtual Controller.
Usage Guidelines
Use this command to view the LDAP server configuration information available on a W-IAP.
Example
The following example shows the output of show ldap-servers command:
LDAP Servers
-----------Name IP Address Port Timeout Retry Count Admin-DN Admin Password
---- ---------- ---- ------- ----------- -------- -------------Server1 192.0.2.5 389 5 3 admin-dn cn=admin password123
Base-DN Filter Key-Attribute In Use
----- ------ ------------- -----dc=example, dc=com (objectclass=*) sAMAccountName No
The output of this command provides the following information:
Command/Parameter
Description
Name
Displays the name of the LDAP authentication server.
IP Address
Displays the IP address of the LDAP server.
Port
Displays the authorization port number of the LDAP server.
Timeout
Displays a timeout value for the LDAP requests from the clients.
Retry Count
Displays number of times that the clients can attempt to connect to the server.
Admin-DN
Displays distinguished name for the administrator.
Admin Password
Displays the password for LDAP administrator.
Base-DN
Displays a distinguished name for the node which contains the entire user
database.
Filter
Shows the filter to apply when searching for a user in the LDAP database.
Key-Attribute
Displays the attribute to use as a key when searching for the LDAP server.
For Active Directory, the value is sAMAccountName
In Use
Indicates if the server is in use.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show ldap-servers | 407
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
408 | show ldap-servers
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show log ap-debug
show log ap-debug <count>
Description
This command shows the W-IAP debug logs.
Syntax
Parameter
Description
<count>
Starts displaying the log output from the specified number of lines of the log.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show log ap-debug | 409
show log apifmgr
show log apifmgr <count>
Description
This command shows the log information for W-IAP interface manager.
Syntax
Parameter
Description
count
Starts displaying the log output from the specified number of lines from the end of
the log.
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
410 | show log apifmgr
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show log convert
show log convert
Description
This command shows image conversion details for the W-IAP.
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show log convert | 411
show log debug
show log debug{count}
Description
This command shows the W-IAP full log.
Syntax
Parameter
Description
<count>
Starts displaying the log output from the specified number of lines from the end
of the log.
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
412 | show log debug
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show log driver
show log driver <count>
Description
This command displays the status of drivers configured on the W-IAP.
Command History
Version
Description
Dell Networking WSeries Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show log driver | 413
show log kernel
show log kernel
Description
This command shows AP’s kernel logs.
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
414 | show log kernel
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show log l3-mobility
show log l3-mobility [<count>]
Description
This command displays the logs for Layer-3 mobility domains configured on a W-IAP.
Syntax
Parameter
Description
<count>
Filters the log output based on the number specified.
Usage Guidelines
Use this command to view the L3-mobility logs for a W-IAP.
Example
The following output is displayed for the show log l3-mobility command:
May 9 21:23:07: Potential Foreign Client Information: mac c4:85:08:de:06:d4 rcvd from self
vlan 0, 1 tid 255 oldapip 0.0.0.0 fapip 10.17.88.59 hapip 0.0.0.0 vcip 0.0.0.0 info l2-timedout,test
May 9 01:43:22: Station Offline: mac 08:ed:b9:e1:51:87 rcvd from self vlan 0, 0 tid 255
oldapip 0.0.0.0 fapip 0.0.0.0 hapip 0.0.0.0 vcip 0.0.0.0 info
May 9 01:25:53: This Client is Normal: mac 08:ed:b9:e1:51:87 sent to self vlan 0, 1 tid 255
oldapip 0.0.0.0 fapip 10.17.88.59 hapip 0.0.0.0 vcip 0.0.0.0 info
May 9 01:25:53: Too many retries: mac 08:ed:b9:e1:51:87 rcvd from self vlan 0, 1 tid 255
oldapip 0.0.0.0 fapip 10.17.88.59 hapip 0.0.0.0 vcip 0.0.0.0 info
May 9 01:25:52: Potential Foreign Client Information: mac 08:ed:b9:e1:51:87 rcvd from self
vlan 0, 1 tid 255 oldapip 0.0.0.0 fapip 10.17.88.59 hapip 0.0.0.0 vcip 0.0.0.0 info l2-timedout,test
The output of this command provides the following information:
Content
Description
Timestamp
Indicates the timestamp of the L3 mobility event.
Client MAC
Indicates the MAC address of the roaming clients.
Event
Provides a description of the mobility event.
Home Vlan
Displays the VLAN ID associated with the home subnet.
VAP Vlan
Displays the VLAN ID associated with the Virtual AP.
tid
Indicates the tunnel interface used for routing packets.
Old AP IP
Indicates the IP address of the W-IAP from which the client has roamed.
FAP IP
Indicates the IP address of the W-IAP in the foreign subnet.
HAP IP
Indicates the IP address of the W-IAP in the home subnet, to which the client is
currently connected.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show log l3-mobility | 415
Content
Description
VC IP
Indicates the IP address of the Virtual Controller.
Additional Info
Displays additional information if any.
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
416 | show log l3-mobility
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show log network
show log network <count>
Description
This command shows network logs for the W-IAP.
Syntax
Parameter
Description
<count>
Starts displaying the log output from the specified number of lines from the end
of the log.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show log network | 417
show log pppd
show log pppd <count>
Description
Shows the Point-to-Point Protocol daemon (PPPd) network connection details.
Syntax
Parameter
Description
<count>
PPPd network count.
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
418 | show log pppd
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show log rapper
show log rapper
Description
This command show details the VPN connection logs in detail.
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show log rapper | 419
show log sapd
show log sapd <count>
Description
This command shows the SAPd details.
Syntax
Parameter
Description
<count>
Starts displaying the log output from the specified number of lines from the end
of the log.
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
420 | show log sapd
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show log security
show log security <count>
Description
This command shows security logs of the W-IAP.
Syntax
Parameter
Description
<count>
Starts displaying the log output from the specified number of lines from the end
of the log.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show log security | 421
show log system
show log system <count>
Description
This command shows system logs of W-IAP.
Syntax
Parameter
Description
<count>
Starts displaying the log output from the specified number of lines from the end
of the log.
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
422 | show log system
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show log upgrade
show log upgrade
Description
This command shows image download from URL and upgrade details for both local image file and URL for the WIAP.
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show log upgrade | 423
show log user
show log user [count]
Description
This command shows the W-IAP user logs.
Syntax
Parameter
Description
count
Starts displaying the log output from the specified number of lines from the end of
the log.
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
424 | show log user
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show log user-debug
show log user-debug [count]
Description
This command shows the W-IAP user debug logs.
Syntax
Parameter
Description
count
Starts displaying the log output from the specified number of lines from the end of
the log.
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show log user-debug | 425
show log vpn-tunnel
show log vpn-tunnel [count]
Description
This command shows VPN tunnel status for the W-IAP.
Syntax
Parameter
Description
count
Starts displaying the log output from the specified number of lines from the end of
the log.
Usage Guidelines
Use this command without the optional <count> parameter to view a complete table of VPN tunnel status. Include
the <count> parameter to display status for the specified count of VPN tunnels.
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
426 | show log vpn-tunnel
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show log wireless
show log wireless [<count>]
Description
This command shows wireless logs of the W-IAP.
Syntax
Parameter
Description
<count>
Starts displaying the log output from the specified number of lines from the end of
the log.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show log wireless | 427
show memory
show memory
Description
Displays the information about memory utilization for a W-IAP.
Usage Guidelines
Use this command to view information about memory utilization on a W-IAP.
Example
The following example shows the output of the show memory command:
MemTotal: 248048 kB
MemFree: 169204 kB
Buffers: 0 kB
Cached: 18164 kB
SwapCached: 0 kB
Active: 21472 kB
Inactive: 12640 kB
Active(anon): 15948 kB
Inactive(anon): 0 kB
Active(file): 5524 kB
Inactive(file): 12640 kB
Unevictable: 0 kB
Mlocked: 0 kB
SwapTotal: 0 kB
SwapFree: 0 kB
Dirty: 0 kB
Writeback: 0 kB
AnonPages: 15972 kB
Mapped: 7728 kB
Shmem: 0 kB
Slab: 32252 kB
SReclaimable: 884 kB
SUnreclaim: 31368 kB
KernelStack: 816 kB
PageTables: 512 kB
NFS_Unstable: 0 kB
Bounce: 0 kB
WritebackTmp: 0 kB
CommitLimit: 124024 kB
Committed_AS: 33616 kB
VmallocTotal: 516096 kB
VmallocUsed: 39452 kB
VmallocChunk: 449532 kB
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
428 | show memory
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show memory | 429
show mgmt-user
show mgmt-user
Description
This command displays the credentials for the admin users for the W-IAP management interface.
Usage Guidelines
Use this command to view the admin user credentials required for accessing the W-IAP and external server
configuration details for the management users.
Examples
The following output is displayed for the show mgmt-user command:
Server Load Balancing :Disabled
Local User DB Backup :Disabled
RADIUS Servers
-------------Name IP Address Port Key Timeout Retry Count
---- ---------- ---- --- ------- ----------Server1 192.0.2.2 1616 23567aea01cb66d354d2b1f5d13df7f85d4a d1d1f181fb4827 5
NAS IP Address NAS Identifier In Use RFC3576
-------------- -------------- ------ ------Yes
Management User Table
--------------------Name Password Type
---- -------- ---admin admin Admin
The output of this command provides the following information:
Column
Description
Server Load Balancing
Indicates if load balancing is enabled when two authentication servers
are used.
Local User DB Backup
Indicates if the backing up of the local user database is enabled.
Name
Indicates the name of the RADIUS server.
IP address
Indicates the IP address of the RADIUS server.
Port
Indicates the authorization port number of the RADIUS server.
Key
Indicates the key for communicating with the RADIUS server.
Timeout
Indicates timeout value in seconds for one RADIUS request.
Retry count
Indicates the maximum number of authentication requests sent to the
RADIUS server.
NAS IP address
Displays the IP address of the Network Access Server (NAS) if NAS is
configured.
NAS Identifier
Indicates the NAS identifier to be sent with the RADIUS requests if
430 | show mgmt-user
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Column
Description
NAS is configured.
In Use
Indicates if the server is in use.
RFC3576
Indicates if the W-IAPs are configured to process RFC 3576-compliant
Change of Authorization (CoA).
NAS IP address
Displays the IP address of the Network Access Server (NAS) if NAS is
configured.
Name (Management User Table)
Indicates the username of the admin user
Password
Indicates the password of the admin user.
Type
Indicates if the type of the user (admin, read-only, or guest management
user).
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.14.0
The output of this command is modified.
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show mgmt-user | 431
show network
show network <name>
Description
This command shows network configuration details for a W-IAP.
Syntax
Parameter
Description
<name>
Displays the name of a network profile.
Usage Guidelines
Use this command without the optional <name> parameter to view a complete configuration details of a network
profile on the W-IAP. Include the <name> parameter to display settings for a single network SSID only.
Example
The following example shows the partial output of show network <name> command:
Name :test
ESSID :test
Status :Enabled
Mode :wpa2-aes
Band :all
Type :employee
Termination :Disabled
Passphrase :
WEP Key :
WEP Key Index :1
VLAN :
Server Load Balancing :Disabled
MAC Authentication :Disabled
L2 Auth Failthrough :Disabled
Captive Portal :disable
Exclude Uplink :none
Hide SSID :Disabled
Content Filtering :Disabled
Auth Survivability :Disabled
Auth Survivability time-out :24
RADIUS Accounting :Disabled
Interim Accounting Interval :0
Radius Reauth Interval :0
DTIM Interval :1
Inactivity Timeout :1000
Legacy Mode Bands :all
G Minimum Transmit Rate :1
G Maximum Transmit Rate :54
A Minimum Transmit Rate :6
A Maximum Transmit Rate :54
Multicast Rate Optimization :Disabled
LEAP Use Session Key :Disabled
Broadcast-filter :none
Max Authentication Failures :0
Blacklisting :Disabled
WISPr :Disabled
Accounting mode :Authentication
432 | show network
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Work without usable uplink :Disabled
Percentage of Airtime: :Unlimited
Overall Limit: :Unlimited
Per-user Limit: :Unlimited
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show network | 433
show network-summary
show network-summary
Description
This command displays the status of the available network configurations on the W-IAP.
Usage Guidelines
Use this command to view the status of the network configurations.
Examples
The following output is displayed for the show network-summary command:
Internet reachable :Detection disabled
Active uplink :eth0
Primary VPN :Not configured
Secondary VPN :Not configured
AirWave :Not configured
The output of this command provides the following information:
Column
Description
Internet Reachable
Indicates the status of the WLAN network.
Active uplink
Indicates the uplink that is currently active on the W-IAP.
Primary VPN
Indicates the status of the Primary VPN configuration.
Secondary VPN
Indicates the status of the Secondary VPN connection.
Airwave
Indicates the status of the W-AirWave configuration.
Command History
Version
Description
Dell Networking W-Series Instant 6.4.0.24.1
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
434 | show network-summary
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show opendns
show opendns [support]
Description
This command displays the open DNS configuration details for a W-IAP.
Syntax
Parameter
Description
support
Displays if the OpenDNS credentials if the OpenDNS service is configured
on the W-IAP.
Usage Guidelines
Use this command to view open DNS configuration details. The OpenDNS credentials are used by Instant to access
OpenDNS to provide enterprise-level content filtering.
Example
The following example shows the output of show opendns command:
OpenDNS
OpenDNS
OpenDNS
OpenDNS
Account :admin
Password :admin123
Status :Not connected
Error Message:N/A
The output of this command includes the following parameters:
Column
Description
OpenDNS Account
Indicates the username for the OpenDNS account.
OpenDNS Password
Indicates the username for the OpenDNS account.
OpenDNS Status
Indicates if the W-IAP is connected to the OpenDNS server.
OpenDNS Error Message
Displays OpenDNS error message.
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show opendns | 435
show port status
show port status
Description
Displays the activity statistics on each of the port on the controller.
Example
The following example shows the output of the show port status command:
(Instant AP)# show port status
Port Type Admin-State Oper-State
---- ---- ----------- ---------bond0 GE down up
Parameter
Description
Port
Displays the port number on the controller.
Type
Displays the port type.
Admin-State
Displays if the port is enabled or disabled.
Oper-State
Displays if the port is currently up and running.
Command History
Version
Description
Dell Networking WSeries Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platforms
Command Mode
All platforms
Privileged Exec mode
436 | show port status
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show pppoe
show pppoe {config|debug logs|debug status}
Description
This command shows PPPoE debug logs and uplink status.
Syntax
Parameter
Description
config
Displays PPPoE configuration details.
debug logs
Displays PPPoE debug logs.
debug status
Displays the uplink status.
Example
show pppoe config
The following example shows the configuration of the PPPoE show pppoe config command.
PPPoE Configuration
------------------Type Value
---- ----User user
Password d226ccefac5a95cd6bb04ca74f20473eae9085fb16892b66
Service name ServiceA
CHAP secret 8acc867926ad85681fd0b0c1a15bb818
Unnumbered dhcp profile dhcpProfile1
show pppoe debug logs
The following example shows the configuration of the PPPoE show pppoe debug logs command.
pppd log not available
show pppoe debug status
The following example shows the configuration of the PPPoE show pppoe debug status command.
pppoe uplink state :Suppressed.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.4
This command was modified.
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show pppoe | 437
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
438 | show pppoe
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show process
show process
Description
This command displays a list of processes running on a W-IAP.
Usage Guidelines
Use this command to view the processes running on the W-IAP for debugging purpose.
Example
The following example shows the partial output for the show process command:
PID Uid VmSize Stat Command
1 root 332 S init
2 root SWN [ksoftirqd/0]
3 root SW< [events/0]
4 root SW< [khelper]
5 root SW< [kthread]
6 root SW< [kblockd/0]
7 root SW [pdflush]
8 root SW [pdflush]
10 root SW< [aio/0]
9 root SW [kswapd0]
992 root 348 S /sbin/udhcpc -i br0 -b
1343 root 744 S /aruba/bin/tinyproxy
1344 root 476 S /aruba/bin/tinyproxy
1345 root 476 S /aruba/bin/tinyproxy
1348 root 476 S /aruba/bin/tinyproxy
1349 root 476 S /aruba/bin/tinyproxy
1350 root 476 S /aruba/bin/tinyproxy
1351 root 476 S /aruba/bin/tinyproxy
1362 root 716 S /usr/sbin/mini_httpd -c *.cgi -d /etc/httpd -u root
1365 root 732 S /usr/sbin/mini_httpd -c *.cgi -d /etc/httpd -u root 1368 root 732 S /usr/sbin/mini_httpd -c *.cgi -d /etc/httpd -u root -
The output of this command provides information on the process ID, user ID of the user running the process, virtual
memory consumed by the process, statistics and the command associated with the processes running on the WIAP.
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show process | 439
show proxy config
show proxy config
Description
This command displays the HTTP proxy configuration settings on a W-IAP.
Example
The following example shows the output of show proxy config command:
Proxy server :192.0.2.1
Proxy port :8080
Exceptions
---------No Exception
-- --------1 192.0.2.2
The output of this command provides the following information:
Parameter
Description
Proxy server
Displays the IP address of the HTTP proxy.
Proxy port
Displays the port number configured for the HTTP proxy.
Exceptions
Displays the IP address of the hosts for which HTTP proxy configuration is not
applied.
Command History
Version
Description
Dell Networking W-Series Instant
6.3.1.1-4.0
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
440 | show proxy config
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show radio config
show radio config
Description
This command displays the 2.4 GHz and 5 GHz radio configuration details for a W-IAP.
Usage Guidelines
Use this command to view the 2.4 GHz and 5 GHz radio configuration details for a W-IAP.
Example
The following example shows the output of show radio config command:
(Instant AP)# show radio config
Legacy Mode:enable
Beacon Interval:100
802.11d/802.11h:enable
Interference Immunity Level:2
Channel Switch Announcement Count:0
MAX Distance:600
Channel Reuse Type:disable
Channel Reuse Threshold:0
Background Spectrum Monitor:disable
5.0 GHz:
Legacy Mode:enable
Beacon Interval:100
802.11d/802.11h:enable
Interference Immunity Level:2
Channel Switch Announcement Count:2
MAX Distance:600
Channel Reuse Type:disable
Channel Reuse Threshold:0
Background Spectrum Monitor:disable
Standalone Spectrum Band:5ghz-upper
The output of this command provides the following information:
Parameter
Description
Legacy Mode
Indicates if the legacy mode is enabled on the W-IAPs to run the radio in the non802.11n mode.
Beacon Interval
Displays beacon interval for the W-IAP in milliseconds. When beacon interval is
configured, the 802.11 beacon management frames are transmitted by the
access point at the specified interval.
802.11d/802.11h
Displays if the W-IAP is allowed advertise its 802.11d (country information) and
802.11h (transmit power control) capabilities.
Interference Immunity
Level
Displays the immunity level configured for an AP radio profile to improve
performance in high-interference environments. For more information on
configuring immunity levels, see rf dot11a-radio-profile and rf dot11g-radioprofile.
Channel Switch
Displays the number of channel switching announcements that are sent before
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show radio config | 441
Parameter
Description
Announcement Count
switching to a new channel.
MAX distance
Indicates the maximum distance in meters between a client and an AP or
between a mesh point and a mesh portal.
Channel Reuse Type
Indicates if channel reuse type is enabled.
Channel Reuse Threshold
Displays the channel reuse threshold configured for channel reuse type.
Background Spectrum
Monitor
Indicates background spectrum monitoring is enabled. When enabled, the WIAPs in access mode continue with normal access service to clients, while
performing additional function of monitoring RF interference (from both
neighboring APs and non Wi-Fi sources such as, microwaves and cordless
phones) on the channel they are currently serving clients.
Standalone Spectrum
Indicates the portion of the channel (upper, middle, or lower) that is being
monitored on the 5 GHz band.
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.4
This command is modified.
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
442 | show radio config
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show radius-servers support
show radius-servers support
Description
This command displays the RADIUS server configuration details for a W-IAP.
Usage Guidelines
Use this command to view the RADIUS server information for a W-IAP.
Example
The following example shows the output of show radius-servers support command:
RADIUS Servers
-------------Name IP Address Port Acctport Key
---- ---------- ---- -------- ---Server1 192.0.2.2 1616 1813 23567aea01cb66d354d2b1f5d13df7f85d4a
Timeout Retry Count NAS IP Address NAS Identifier In Use RFC3576
---- ---------- ------------ --------------- ------- --------------d1d1f181fb4827 5 Yes 0
Airgroup RFC3576-ONLY Airgroup RFC3576 port Deadtime
-------- ------------ ---------------------- -----------5
The output of this command provides the following information:
Parameter
Description
Name
Indicates the name of the RADIUS server.
IP address
Indicates the IP address of the RADIUS server.
Port
Indicates the authorization port number of the RADIUS server.
AcctPort
Indicates the authorization port number of the RADIUS server.
Key
Indicates the key for communicating with the RADIUS server.
Timeout
Indicates timeout value in seconds for one RADIUS request.
Retry count
Indicates the maximum number of authentication requests sent to the
RADIUS server.
NAS IP address
Displays the IP address of the Network Access Server (NAS) if NAS is configured.
NAS Identifier
Indicates the NAS identifier to be sent with the RADIUS requests.
In Use
Indicates if the server is in use.
RFC3576
Indicates if the W-IAPs are configured to process RFC 3576-compliant Change of
Authorization (CoA).
Airgroup RFC3576-ONLY
Indicates if W-IAPs are configured to be RFC 3576 compliant only.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show radius-servers support | 443
Parameter
Description
Airgroup RFC3576 port
Indicates the port number used for sending AirGroup CoA.
Deadtime
Indicates the RADIUS server dead-time.
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
444 | show radius-servers support
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show rft trans-id
show rft trans-id {<id>| all}
Description
This command shows the transaction IDs of tests performed for RF troubleshooting.
Syntax
Parameter
Description
<id>
Indicates the transaction ID for which you want to view the output.
all
Displays all the transaction IDs associated with the RF tests.
Usage guidelines
Use the show rft trans-id command to view the transaction IDs for the most recent test performed for RF
troubleshooting.
Example
The following example shows the transaction IDs for the latest RF tests.
(Instant AP)# show rft trans-id 201
Command History
Version
Description
Dell Networking W-Series Instant
6.4.0.2-4.1
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show rft trans-id | 445
show rft profile
show rft profile {all|antenna-connectivity|ht-link-quality|link-quality|raw}
Description
This command shows the RF test profile for testing RF parameters such as antenna connectivity, link quality, and
channel link quality.
Syntax
Parameter
Description
all
Displays the parameters for all test profiles.
antenna-connectivity
Displays the parameters details for the antenna-connectivity test profile.
ht-link-quality
Displays the parameter details for the HT link quality test profile.
link-quality
Displays the parameter details for the link quality test profile.
raw
Displays the parameter details for the raw test profile.
Usage guidelines
Use the show rft profile command to view the test profile parameters for RF troubleshooting.
Example
The following example shows the profile parameters for all RF test profiles:
(Instant AP)# show rft profile all
Profile RAW: Built-in profile
----------------------------Parameter Value
--------- ----Antenna 1 and/or 2
Frame Type Null Data
Num Packets 100
Packet Size 1500
Num Retries 3
Profile LinkQuality: Built-in profile
-------------------------------------Parameter Value
--------- ----Antenna 1 and/or 2
Frame Type Null Data
Num Packets 100 for each data-rate
Packet Size 1500
Num Retries 0
Data Rate All rates are tried
Profile HTLinkQuality: Built-in profile
---------------------------------------Parameter Value
--------- ----Antenna 1 and/or 2
Frame Type Null Data
Num Packets 100 for each data-rate
Packet Size 1500
446 | show rft profile
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Num Retries 0
Data Rate All rates are tried
Profile AntennaConnectivity: Built-in profile
---------------------------------------------Parameter Value
--------- ----Frame Type Null Data
Num Packets 100
Packet Size 1500
Num Retries 0
Radio 0 (1 for AP-80-S only)
Command History
Version
Description
Dell Networking W-Series Instant
6.4.0.2-4.1
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show rft profile | 447
show running-config
show running-config
Description
This command displays the current configuration running on a W-IAP, including the current changes that are yet to
be saved.
Usage Guidelines
Use this command to view the current configuration information stored in the W-IAP flash memory.
Example
The following example shows the partial output of the show running-config command output:
version 6.4.0.0-4.1.0
virtual-controller-country IN
virtual-controller-key 0cb5770401cdeb6e4363c25fdfde17d907c4b095a9be5e
name instant-C4:42:98
terminal-access
clock timezone none 00 00
rf-band all
allow-new-aps
allowed-ap d8:c7:c8:c4:42:98
arm
wide-bands 5ghz
80mhz-support
min-tx-power 18
max-tx-power 127
band-steering-mode prefer-5ghz
air-time-fairness-mode fair-access
client-aware
scanning
client-match
syslog-level warn ap-debug
syslog-level warn network
syslog-level warn security
syslog-level warn system
syslog-level warn user
syslog-level warn user-debug
syslog-level warn wireless
mgmt-user admin aba950f14f5764975371fcb66a72d10f
wlan access-rule default_wired_port_profile
index 1
rule any any match any any any permit
wlan access-rule wired-instant
index 2
rule masterip 0.0.0.0 match tcp 80 80 permit
rule masterip 0.0.0.0 match tcp 4343 4343 permit
rule any any match udp 67 68 permit
rule any any match udp 53 53 permit
wlan access-rule test
index 3
rule any any match any any any deny
wlan ssid-profile test
enable
index 1
type employee
essid instant
opmode opensystem
448 | show running-config
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
max-authentication-failures 0
rf-band all
captive-portal disable
dtim-period 1
inactivity-timeout 1000
broadcast-filter none
dmo-channel-utilization-threshold 90
local-probe-req-thresh 0
max-clients-threshold 64
dot11k
dot11v
auth-survivability cache-time-out 24
wlan external-captive-portal
server localhost
port 80
url "/"
auth-text "Authenticated"
auto-whitelist-disable
https
blacklist-time 3600
auth-failure-blacklist-time 3600
ids
wireless-containment none
wired-port-profile wired-instant
switchport-mode access
allowed-vlan all
native-vlan guest
no shutdown
access-rule-name wired-instant
speed auto
duplex auto
no poe
type guest
captive-portal disable
no dot1x
wired-port-profile default_wired_port_profile
switchport-mode trunk
allowed-vlan all
native-vlan 1
shutdown
access-rule-name default_wired_port_profile
speed auto
duplex full
no poe
type employee
captive-portal disable
no dot1x
enet0-port-profile default_wired_port_profile
uplink
preemption
enforce none
failover-internet-pkt-lost-cnt 10
failover-internet-pkt-send-freq 30
failover-vpn-timeout 180
airgroup
disable
airgroupservice airplay
disable
description AirPlay
airgroupservice airprint
disable
description AirPrint
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show running-config | 449
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
450 | show running-config
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show snmp-configuration
show snmp-configuration
Description
This command displays the Simple Network Management Protocol (SNMP) configuration details for a Virtual
Controller.
Usage Guidelines
Use this command to view the SNMP information configured on a Virtual Controller.
Example
The following example shows the output of show snmp-configuration command:
Engine ID:D8C7C8CBD420
Community Strings
----------------Name
---SNMPv3 Users
-----------Name Authentication Type Encryption Type
---- ------------------- --------------SNMP Trap Hosts
--------------IP Address Version Name Port Inform
---------- ------- ---- ---- ------
The output of this command includes the following parameters:
Parameter
Description
Engine ID
Displays the SNMP engine ID.
Community Strings
Displays the SNMP community strings..
SNMPv3 Users
Displays details about the SNMPv3 users.
Name
Indicates the name of the SNMP user
Authentication Type
Indicates the authentication protocol configured for the SNMP users.
Encryption Type
Indicates the encryption type, for example, Advanced Encryption Standard
(AES) or CBC-DES Symmetric Encryption Protocol (DES) configured for SNMP
users.
SNMP Trap Hosts
Displays the traps generated by the host system.
IP Address
Indicates the host IP address generating the SNM trap.
Version
Displays the SNMP version for which the trap is generated.
Name
Indicates the name of system generating the SNMP traps.
Port
Indicates the port number to which notification messages are sent.
Inform
Displays the SNMP inform messages to send to the configured host.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show snmp-configuration | 451
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
452 | show snmp-configuration
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show snmp trap-queue
show snmp trap-queue
Description
This command displays the list of SNMP traps in queue.
Usage Guidelines
Use this command to view the SNMP traps in queue.
Example
The following example shows the partial output of show snmp trap-queue command:
2013-05-12 14:05:27 An AP (NAME d8:c7:c8:cb:d4:20 and MAC d8:c7:c8:cb:d4:20 on RADIO 2)
detected an interfering access point (BSSID 00:24:6c:80:7d:11 and SSID NTT-SPOT on CHANNEL 1).
2013-05-12 14:09:53 An AP (NAME d8:c7:c8:cb:d4:20 and MAC d8:c7:c8:cb:d4:20 on RADIO 2)
detected an interfering access point (BSSID 6c:f3:7f:45:5d:20 and SSID 7SPOT on CHANNEL 1).
2013-05-12 14:10:36 An AP (NAME d8:c7:c8:cb:d4:20 and MAC d8:c7:c8:cb:d4:20 RADIO 2) changed
its channel from channel 1 (secchan offset 1) to channel 7 (secchan offset 1) due to reason
12.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show snmp trap-queue | 453
show spectrum-alert
show spectrum-alert
Description
This command displays the list of spectrum alerts for a W-IAP.
Syntax
Parameter
Description
<count>
Filters the alerts based on the specified number.
Usage Guidelines
Use this command to view the spectrum alerts for a W-IAP. When a new non Wi-Fi device is found, an alert is
reported to the Virtual Controller. The spectrum alert messages provide information about the device ID, device type,
IP address of the spectrum monitor or hybrid AP, and the timestamp. The Virtual Controller reports the detailed
device information to W-AirWave Management server.
Example
The following example shows the output for the show spectrum-alert command when no alerts are generated.
Spectrum Alerts
--------------Timestamp Type ID Access Point
--------- ---- -- ------------
The output of this command provides the following information:
Parameter
Description
Timestamp
Displays the time at which alert was recorded.
Type
Displays the type of the device that generated the alert.
ID
Displays the device ID for which the alert is generated.
Access Point
Displays the IP address of the W-IAP.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
454 | show spectrum-alert
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show stats
show stats {ap <IP-address>| client <MAC-address> | global | network <network-name>} [count]
Description
This command displays the aggregate statistics for W-IAPs, W-IAP clients, W-IAP cluster, and network profiles
configured on a W-IAP.
Syntax
Parameter
Description
ap <IP-address>
Displays information on W-IAP utilization, RF trends, and client details for a
specific W-IAP.
client <MAC-address>
Displays information on a client and its mobility records, the cluster to which the
client has joined, and the details of the W-IAP to which it is currently connected.
global
Displays global statistics for the W-IAP cluster, and the W-IAPs and clients
connected to the W-IAP cluster.
network <networkname>
Displays aggregate information about a network profile configured on a W-IAP.
[count]
Allows you to filter the command output for the W-IAP, client, global, and network
profile statistics based on the specified number.
Usage Guidelines
Use this command to view the following information about W-IAPs, the clients connected to the W-IAPs, and the
corresponding W-IAP cluster:
l
Utilization trend — Displays information about the W-IAP utilization, the number of clients associated with a WIAP, Virtual Controller, or the W-IAP network over the last 15 minutes.
l
RF trends — Displays information the utilization, noise, or error threshold for a W-IAP. It also shows the current
speed or signal strength for the clients in the network and the RF information for the W-IAPs to which the clients
are connected.
l
Mobility Trail — Shows duration of the client is association with a W-IAP and the name of the W-IAP to which it is
currently connected.
Examples
show stats ap
The following example shows the output for the show stats ap <IP-address> command:
Util Level:good
Noise Level:good
Error Level:good
2.4 GHz Channel:7
5.0 GHz Channel:149+
Usage
----Timestamp CPU Utilization (%) Memory Free (MB) Neighboring APs [Valid] Neighboring APs
[Interfering] Neighboring APs [Rogue] Neighboring Clients [Valid] Neighboring Clients
[Interfering] Clients Throughput [Out] (bps) Throughput [In] (bps)
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show stats | 455
--------- ------------------- ---------------- ----------------------- ---------------------------- ----------------------- --------------------------- --------------------------------- ------ ---------------------- --------------------00:34:46 8 164 4 239 0 1 8 1 93 99
00:34:17 8 164 4 239 0 1 8 1 186 199
0 1 9
RF Trends
--------Timestamp Utilization [2.4 GHz] (%) Utilization [5.0 GHz] (%) Noise Floor [2.4 GHz]
(dBm) Noise Floor [5.0 GHz] (dBm) 2.4 GHz Frames [Errors] (fps) 5.0 GHz Frames [Errors] (fps)
2.4 GHz Frames [Out] (fps) 5.0 GHz Frames [Out] (fps) 2.4 GHz Frames [In] (fps) 5.0 GHz Frames
[In] (fps) 2.4 GHz Frames [Drops] (fps) 5.0 GHz Frames [Drops] (fps) 2.4 GHz Mgmt Frames [In]
(fps) 5.0 GHz Mgmt Frames [In] (fps) 2.4 GHz Mgmt Frames [Out] (fps) 5.0 GHz Mgmt Frames [Out]
(fps)
----- --------------------------- ----------------------------- ------------------------------------------------------ -------------------------- ------------------------- ------------------------ ---------------------------- ---------------------------- ----------------------------- ------------------------------ ------------------------------- -----------------------------00:34:46 59 4 -91 -93 41 0 0 0 68 18 1 1 403 265 1 0
00:34:17 61 5 -92 -93 45 0 0 1 78 21 1 1 408 287 1 1
Client Heatmap
-------------Clients Signal Speed IP Address
------- ------ ----- ---------AP List
------Name IP Address Mode Spectrum Clients Type CPU Utilization %: Memory Free (MB): Serial Number:
Need Antenna Config From Port
---- ---------- ---- -------- ------- ---- ------------------ ----------------- -------------------------------- --------d8:c7:c8:cb:d4:20 10.17.88.188 access disable 1 135 8 164 AX0059921 No none
show stats client
The following example shows the output for the show stats client <mac> command:
Name::
IP Address::169.254.90.154
MAC Address::08:ed:b9:e1:51:7d
Access Point::d8:c7:c8:cb:d4:20
Channel::149+
Network::Network1
Connection Time::4h:50m:48s
Type::AN
OS::
Swarm Client Stats
-----------------Timestamp Signal (dB) Frames [In] (fps) Frames [Out] (fps) Throughput [In] (bps) Throughput
[Out] (bps) Frames [Retries In] (fps) Frames [Retries Out] (fps) Speed (mbps)
--------- ----------- ----------------- ------------------ --------------------- --------------------- ------------------------- -------------------------- -----------00:32:46 47 0 0 0 170 0 0 6
00:32:16 47 0 0 0 170 0 0 6
00:31:46 47 0 1 0 5946 0 0 6
00:31:16 49 0 0 0 316 0 0 6
Mobility Trail
-------------Association Time Access Point
---------------- -----------11:04:56 d8:c7:c8:cb:d4:20
Client Heatmap
--------------
456 | show stats
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Client Signal Speed IP Address
------ ------ ----- ---------169.254.90.154 good good 169.254.90.154
Access Point Heatmap
-------------------Access Point Utilization Noise Errors
------------ ----------- ----- -----d8:c7:c8:cb:d4:20 good good good
Client List
----------Name IP Address MAC Address OS Network Access Point Channel Type Role
---- ---------- ----------- -- ------- ------------ ------- ---- ---169.254.90.154 08:ed:b9:e1:51:7d Network1 d8:c7:c8:cb:d4:20 149+ AN Network1
Info timestamp :48662
show stats global
The following example shows the output for the show stats global command:
Swarm Global Stats
-----------------Timestamp Clients Frames [Out] (fps) Frames [In] (fps) Throughput [Out] (bps) Throughput [In]
(bps)
--------- ------- ------------------ ----------------- ---------------------- -------------------00:38:05 1 0 0 294 380
00:37:35 1 0 0 98 101
00:37:04 1 0 0 0 0
00:36:33 1 0 0 0 0
00:36:03 1 0 0 0 0
00:35:32 1 0 0 46 49
00:35:01 1 0 0 93 99
00:34:31 1 0 0 186 199
00:34:00 1 0 0 0 0
00:33:29 1 0 0 0 0
00:32:59 1 0 0 0 170
00:32:28 1 0 0 0 170
00:31:58 1 0 1 2961 5946
00:31:27 1 0 0 196 316
00:30:56 1 0 0 196 202
Access Point Heatmap
-------------------Access Points Utilization Noise Errors
------------- ----------- ----- -----Client Heatmap
-------------Clients Signal Speed IP Address
------- ------ ----- ----------
show stats network
The following example shows the output for the show stats network <network-name> command:
Swarm Network Stats
------------------Timestamp Clients Frames [Out] (fps) Frames [In] (fps) Throughput [Out] (bps) Throughput [In]
(bps)
--------- ------- ------------------ ----------------- ---------------------- -------------------16:39:25 0 0 0 0 0
16:38:55 0 0 0 0 0
16:38:25 0 0 0 0 0
16:37:54 0 0 0 0 0
16:37:24 0 0 0 0 0
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show stats | 457
16:36:54 0 0 0 0 0
16:36:24 0 0 0 0 0
16:35:54 0 0 0 0 0
16:35:23 0 0 0 0 0
16:34:53 0 0 0 0 0
16:34:23 0 0 0 0 0
Access Point Heatmap
-------------------Access Points Utilization Noise Errors
------------- ----------- ----- -----d8:c7:c8:c4:42:98 poor good good
Client Heatmap
-------------Clients Signal Speed IP Address
------- ------ ----- ---------Name :test123
ESSID :test123
Status :Enabled
Mode :wpa2-aes
Band :all
Type :employee
Termination :Disabled
Passphrase :
WEP Key :
WEP Key Index :1
VLAN :
Server Load Balancing :Disabled
MAC Authentication :Disabled
L2 Auth Failthrough :Disabled
Captive Portal :disable
Exclude Uplink :none
Hide SSID :Disabled
Content Filtering :Disabled
Auth Survivability :Disabled
Auth Survivability time-out :24
RADIUS Accounting :Disabled
Interim Accounting Interval :0
Radius Reauth Interval :0
DTIM Interval :1
Inactivity Timeout :1000
Legacy Mode Bands :all
G Minimum Transmit Rate :1
G Maximum Transmit Rate :54
A Minimum Transmit Rate :6
A Maximum Transmit Rate :54
Multicast Rate Optimization :Disabled
LEAP Use Session Key :Disabled
Broadcast-filter :none
Max Authentication Failures :0
Blacklisting :Disabled
WISPr :Disabled
Accounting mode :Authentication
Work without usable uplink :Disabled
Percentage of Airtime: :Unlimited
Overall Limit: :Unlimited
Per-user Limit: :Unlimited
Access Control Type: :Role
Machine-only Role: :test1
User-only Role: :test1
Dynamic Multicast Optimization :Disabled
DMO Channel Utilization Threshold :90
Local Probe Request Threshold :0
458 | show stats
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Max Clients Threshold :64
Background WMM Share :0
Best Effort WMM Share :0
Video WMM Share :0
Voice WMM Share :0
Certificate Installed: :No
Internal Radius Users: :0
Internal Guest Users: :0
Role Derivation Rules
--------------------Attribue Operation Operand Role Name Index
-------- --------- ------- --------- ----Vlan Derivation Rules
--------------------Attribue Operation Operand Vlan Id
-------- --------- ------- ------RADIUS Servers
-------------Name IP Address Port Key Timeout Retry Count NAS IP Address NAS Identifier RFC3576
---- ---------- ---- --- ------- ----------- -------------- -------------- ------test 10.0.0.1 1812 test123 5 3
test123 10.0.0.0 1812 test123 5 3
LDAP Servers
-----------Name IP Address Port Timeout Retry Count Admin-DN Admin Password Base-DN
---- ---------- ---- ------- ----------- -------- -------------- ------test 0.0.0.0 0 5 3
Access Rules
-----------Dest IP Dest Mask Dest Match Protocol (id:sport:eport) Action Log TOS 802.1P Blacklist Mirror
DisScan ClassifyMedia
------- --------- ---------- ------------------------- ------ --- --- ------ --------- ------------ ------------any any match any permit
Vlan Id :0
ACL Captive Portal:disable
:Captive Portal Configuration
Background Color:13421772
Banner Color :16750848
Decoded Texts :
Banner Text :Welcome to Guest Network
Use Policy :Please read terms and conditions before using Guest Network
Terms of Use :This network is not secure, and use is at your own risk
Internal Captive Portal Redirect URL:
Captive Portal Mode:Acknowledged
:External Captive Portal Configuration
Server:localhost
Port :80
URL :/
Authentication Text:Authenticated
External Captive Portal Redirect URL:
Server Fail Through:No
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show stats | 459
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
460 | show stats
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show subscription-aps
show subscription-aps
Description
This command displays the subscription status of a W-IAP.
Example
(Instant AP) (config) # show subscription-aps
IAP controlled by Cloud-Server:disable
subscription enabled by manually :disable
Subscription Ap List
-------------------MAC Address Status
----------- -----d8:c7:c8:c4:56:de ACTIVE
d8:c7:c8:c4:57:06 ACTIVE
Command History
Version
Description
Dell Networking WSeries Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show subscription-aps | 461
show summary
show summary {<difference> | support}
Description
This command shows the current configuration details.
Syntax
Parameter
Description
<difference>
Shows the difference in configuration.
support
Shows the summary support containing the configuration details used by support.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.4
This command was modified.
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
462 | show summary
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show swarm
show swarm {state|mode}
Description
This command displays the current status of the W-IAP cluster and indicates if W-IAPs are in a cluster or standalone
mode.
Usage Guidelines
Use this command to view the current status of the W-IAP cluster and to view information about the functioning
mode of the W-IAP cluster.
Example
The following example shows the output of show swarm state command:
AP Swarm State :swarm_config_sync_complete
mesh ldart State :suspending
The output of this command describes synchronization status of the W-IAP cluster.
The following text shows an example output for the show swarm mode command:
Swarm Mode :Cluster
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show swarm | 463
show supported-cert-formats
show supported-cert-formats
Description
This command displays the supported server and CA certificate formats.
Usage Guidelines
Use this command to view the list certificate formats supported by the W-IAP.
Examples
Server Certificate Formats
-------------------------Name
---PEM
CA Certificate Formats
---------------------Name
---PEM
DER
Command History
Version
Description
Dell Networking W-Series
Instant 6.3.1.1-4.0
The output of this command is modified.
Dell Networking W-Series
Instant 6.2.1.0-3.4
This command was modified.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
464 | show supported-cert-formats
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show syslog-level
show syslog-level
Description
This command displays the Syslog logging levels configured for a W-IAP.
Usage Guidelines
Use this command to view the Syslog logging facilities and the associated logging level.
Example
The following example shows to output of the show syslog-level command:
Logging Level
------------Facility Level
-------- ----ap-debug debug
network debug
security debug
system debug
user debug
user-debug debug
wireless debug
The output of this command provides the following information:
Parameter
Description
Facility
Displays the list of logging facilities configured on the W-IAP.
ap-debug
Generates a log for the AP device for debugging purposes.
network
Generates a log when there is a change in the network, for example, when a new W-IAP
is added to a network.
security
Generates a log for network security, for example, when a client connects using wrong
password.
system
Generates a log about the system configuration and status.
user
Generates a log for the W-IAP clients.
user-debug
Generates a detailed log about the clients for debugging purposes.
wireless
Generates a log about radio configuration.
syslog-level
<level>
Displays any of the following Syslog logging level configured for the Syslog facility.
l
l
l
l
l
l
l
l
Emergency — Panic conditions that occur when the system becomes unusable.
Alert — Any condition requiring immediate attention and correction.
Critical — Any critical conditions, for example, hard drive error.
Errors —Error conditions.
Warning — Warning messages.
Notice — Significant events of a non-critical and normal nature. The default value for
all Syslog facilities.
Informational — Messages of general interest to system users.
Debug — Messages containing information useful for debugging.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show syslog-level | 465
Command History
Version
Description
Dell Networking WSeries Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
466 | show syslog-level
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show tacacs-servers
show tacacs-servers
Description
This command displays all the tacacs servers configured on a W-IAP.
Usage Guidelines
Use this command to view the list of tacacs servers available on a W-IAP.
Example
The following example shows the output of the show tacacs-servers command:
TACACS Servers
-------------Name IP Address Port Key Timeout Retry Count In Use
---- ---------- ---- --- ------- ----- ----- -----tacacs1 10.64.16.240 49 pass123 20 1 Yes
tacacs2 192.168.0.100 49 pass456 10 2 No
The output of this command provides the following information:
Parameter
Description
Name
Indicates the list of tacacs server available on a W-IAP.
IP Address
Displays the IP address for each tacacs server.
Port
Indicates the TCP Port in use for the tacacs server.
key
Indicates the shared secret key used to authenticate and access tacacs server.
Command History
Version
Description
Dell Networking W-Series
Instant 6.4.0.2-4.1
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show tacacs-servers | 467
show tech-support
show tech-support
Description
This command displays the complete W-IAP information and the associated configuration details, which can be
used by the technical support representatives for debugging.
Usage Guidelines
Use this command to view and analyze W-IAP configuration details for debugging any AP related issues.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
468 | show tech-support
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show uncommitted-config
show uncommitted-config
Description
This command displays the current configuration details that are yet to be committed and saved on the W-IAP.
Usage Guidelines
Use this command to view the uncommitted configuration details. Use the commit apply command to commit the
configuration changes.
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show uncommitted-config | 469
show upgrade info
show upgrade info
Description
This command displays the image upgrade details for a W-IAP.
Usage Guidelines
Use this command to view the image upgrade details for a W-IAP.
Example
The following example shows the output of show upgrade info command:
Image Upgrade Progress
---------------------Mac IP Address AP Class Status Image Info Error Detail
--- ---------- -------- ------ ---------- -----------d8:c7:c8:cb:d4:20 10.17.88.188 Cassiopeia image-ok image file none
Auto reboot :enable
Use external URL :disable
The output of this command provides the following information:
Parameter
Description
Mac
Shows the MAC address of the W-IAP.
IP Address
Shows the IP address of the W-IAP.
AP Image Class
Indicates the W-IAP class. The following examples describe the image class
for different W-IAP models:
l For W-IAP 135/134 —DellInstant_Cassiopeia_<build-version>
l For W-IAP108/109, W-IAP103, and W-IAP114/115— DellInstant_Pegasus_
<build-version>
l For W-IAP155/155P—DellInstant_Aries_<build-version>
l For W-IAP224/225 and W-IAP274/275—DellInstant_Centaurus_<buildversion>
l For all other W-IAPs —DellInstant_Orion_<build-version>
Status
Indicate the current status of the image upgrade.
Image Info
Indicates the source of image.
Error Detail
Displays errors generated when an upgrade fails.
Auto Reboot
Indicates if automatic rebooting of W-IAP is enabled on a successful upgrade.
Use External URL
Indicates if an external URL can be used for loading an image file.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
470 | show upgrade info
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show upgrade info | 471
show uplink
show uplink {config|stats}
Description
This command displays uplink configuration details and status of for a W-IAP.
Syntax
Parameter
Description
show uplink config
Displays the uplink interface configuration details for a W-IAP.
show uplink stats
Displays the aggregate uplink statistics for a W-IAP
Usage Guidelines
Use this command to view the information about uplink status and configuration for a W-IAP.
Example
The following output is displayed for the show uplink config command:
Uplink preemption :enable
Uplink enforce :none
Ethernet uplink eth0 :DHCP
Internet failover :disable
Max allowed test packet loss:10
Secs between test packets :30
VPN failover timeout (secs) :180
The output of this command provides the following information:
Column
Description
Uplink preemption
Indicates if the uplink preemption is enabled.
Uplink enforce
Indicates if any uplinks are enforced.
Ethernet uplink eth0
Indicates if Ethernet uplink is configured.
Max allowed test packet loss
Indicates an allowed number of test packets that can be lost verifying
the Internet availability.
Secs between test packets
Indicates the frequency at which the test packets are sent to verify the
Internet availability.
VPN failover timeout (secs)
Indicates the number of seconds to wait, before trying a different uplink
when a VPN tunnel is down.
The following output is displayed for the show uplink status command:
Uplink preemption :enable
Uplink enforce :none
Ethernet uplink eth0 :DHCP
Uplink Table
-----------Type State Priority In Use
---- ----- -------- -----472 | show uplink
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
eth0 UP 0 Yes
Wifi-sta INIT 6 No
3G/4G INIT 7 No
Internet failover :disable
Max allowed test packet loss:10
Secs between test packets :30
VPN failover timeout (secs) :180
ICMP pkt sent :0
ICMP pkt lost :0
Continuous pkt lost :0
VPN down time :0
The output of this command provides the following information:
Column
Description
Uplink preemption
Indicates if the uplink preemption is enabled.
Uplink enforce
Indicates if any uplinks are enforced.
Ethernet uplink eth0
Indicates if Ethernet uplink is configured.
Type
Indicates the type of the uplink.
State
Indicates the uplink status.
Priority
Indicates if any priority levels are assigned to the uplink.
In Use
Indicates if the uplink is in use.
Max allowed test packet loss
Indicates an allowed number of test packets that can be lost verifying
the Internet availability.
Secs between test packets
Indicates the frequency at which the test packets are sent to verify the
Internet availability.
VPN failover timeout (secs)
Indicates the number of seconds to wait, before trying a different uplink
when a VPN tunnel is down.
ICMP pkt sent
Indicates the number of ICMP packets sent to verify the Internet
availability for uplink switchover.
ICMP pkt lost
Indicates the number of ICMP packets lost.
Continuous pkt lost
Indicates if the packets are lost continuously.
VPN down time
Indicates the time since the VPN connection is unavailable.
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show uplink | 473
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
474 | show uplink
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show uplink-vlan
show uplink-vlan
Description
This command displays the uplink VLAN configuration details for the management traffic.
Usage Guidelines
Use this command to view the uplink VLAN configuration details for management traffic. The uplink management
VLAN configuration allows you to tag management traffic and connect multiple W-IAP clusters (Virtual Controllers)
to the same port on an upstream switch (for example, W-AirWave server).
Example
The following output is displayed for the show uplink-vlan command:
Uplink Vlan Current :0
Uplink Vlan Provisioned :
The output of this command provides the following information:
Column
Description
Uplink Vlan Current
Indicates if the VLAN ID.
Uplink Vlan Provisioned
Indicates if the uplink VLAN is provisioned.
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show uplink-vlan | 475
show users
show user [portal| Radius]
Description
This command displays users configured for a W-IAP.
Syntax
Parameter
Description
portal
Displays the W-IAP user credentials.
radius
Displays the user credentials for the RADIUS server authentication
Usage Guidelines
Use this command to view the W-IAP user credentials.
Examples
The following output is displayed for the show user command:
show user
User Table
---------Name Password Attribute
---- -------- --------d8:c7:c8:cb:d4:20# show user portal
Portal User Table
----------------Name Password
---- -------d8:c7:c8:cb:d4:20# show user radius
Radius User Table
----------------Name Password
---- --------
The output of this command provides the following information:
Column
Description
Name
Indicates the username of the W-IAP, portal, and the RADIUS users.
Password
Indicates the password details of the users.
Attribute
Indicates the attributes
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
476 | show users
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show users | 477
show valid-channels
show valid-channels
Description
This command displays the list of channels that are valid for a W-IAP serving a specific regulatory domain.
Usage Guidelines
Use this command to view the list of valid channels that can be configured on your W-IAP.
Example
The following example shows the output of show valid-channels command:
2.4 GHz
1
2
3
4
5
6
7
8
9
10
11
12
13
1+
2+
3+
4+
5+
6+
7+
5.0 GHz
36
40
44
48
52
56
60
64
149
153
157
161
165
36+
44+
52+
60+
149+
157+
The output of this command provides the following information:
478 | show valid-channels
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Parameter
Description
2.4 GHz
Displays the list of channels valid for a W-IAP in the 2.4 GHz band.
5.0 GHz
Displays the list of channels valid for a W-IAP in the 5.0 GHz band.
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show valid-channels | 479
show version
show version
Description
This command displays the Instant software version running on a W-IAP.
Example
The following example shows the output of the show version command:
Aruba Operating System Software.
ArubaOS (MODEL: W-AP105), Version 6.3.1.1-4.0.0.0
website: http://www.dell.com
Copyright (c) 2002-2013, Aruba Networks, Inc.
Compiled on 2013-11-18 at 09:46:18 PST (build 40933) by p4build
AP uptime is 2 days 3 hours 32 minutes 48 seconds
Reboot Time and Cause: AP rebooted Wed Nov 20 05:28:48 UTC 2013; Image Upgrade Successful
The output of this command provides the following information:
Parameter
Description
Version
Indicates the version of W-IAP software.
Reboot Time and Cause
Indicates the reason for which the W-IAP was last rebooted and the reboot
time.
Model
Indicates the W-IAP model.
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
480 | show version
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show vpn
show vpn {config|status|tunnels}
Description
This command displays the status and configuration details for VPN-enabled W-IAPs.
Syntax
Parameter
Description
config
Displays configuration details for the VPN-enabled W-IAPs.
status
Displays the status of the VPN connections enabled on a W-IAP.
tunnels
Displays the IAP-VPN retry counter statistics.
Example
The following example shows the output displayed for show vpn config command:
Concentrator
-----------Type Value
---- ----VPN Primary Server
VPN Backup Server
VPN Preemption disable
VPN Fast Failover disable
VPN Hold Time 600
VPN Monitor Pkt Send Freq 5
VPN Monitor Pkt Lost Cnt 2
VPN Ikepsk
VPN Username
VPN Password 95a5624fbf08dfb3e794ac2c6686e330
GRE outside vpn disable
GRE Server
GRE IP Address 0.0.0.0
GRE Type 1
GRE Per AP Tunnel disable
Reconnect User On Failover disable
Reconnect Time On Failover 60
Routing Table
------------Destination Netmask Gateway Type
----------- ------- ------- ----
The output displayed for this command provides information on the parameters configured for the VPN concentrator.
For more information on the VPN configuration parameters, see the following commands:
l
vpn primary
l
vpn backup
l
vpn preemption
l
vpn fast-failover
l
vpn gre-outside
l
vpn hold-time
l
vpn monitor-pkt-lost-cnt
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show vpn | 481
l
vpn monitor-pkt-send-freq
l
vpn ikepsk
l
gre type
l
gre primary
l
gre per-ap-tunnel
The following example shows the output displayed for show vpn status command:
profile name:default
-------------------------------------------------current using tunnel :unselected tunnel
ipsec is preempt status :disable
ipsec is fast failover status :disable
ipsec hold on period :600
ipsec tunnel monitor frequency (seconds/packet) :5
ipsec tunnel monitor timeout by lost packet cnt :2
ipsec primary tunnel crypto type :Cert
ipsec primary tunnel peer address :N/A
ipsec primary tunnel peer tunnel ip :N/A
ipsec primary tunnel ap tunnel ip :N/A
ipsec primary tunnel current sm status :Init
ipsec primary tunnel tunnel status :Down
ipsec primary tunnel tunnel retry times :0
ipsec primary tunnel tunnel uptime :0
ipsec backup tunnel crypto type :Cert
ipsec backup tunnel peer address :N/A
ipsec backup tunnel peer tunnel ip :N/A
ipsec backup tunnel ap tunnel ip :N/A
ipsec backup tunnel current sm status :Init
ipsec backup tunnel tunnel status :Down
ipsec backup tunnel tunnel retry times :0
ipsec backup tunnel tunnel uptime :0
The show vpn status command displays the current status of VPN connection, IP address configured for
VPN/IPSec connections, and the tunnel details.
Command History
Version
Description
Dell Networking W-Series Instant 6.4.0.2-4.1
The tunnels keyword was added.
Dell Networking W-Series Instant 6.3.1.1-4.0
The command output is modified.
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
482 | show vpn
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show walled-garden
show walled-garden
Description
This command displays the domain names and websites that are blacklisted or whitelisted by a W-IAP.
Usage Guidelines
Use this command to view the walled garden configuration details for a W-IAP. A walled garden typically controls
access to Web content and services. The Walled garden access is required when an external captive portal is used.
For example, a hotel environment where the unauthenticated users are allowed to navigate to a designated login
page (for example, a hotel website) and all its contents.
The users who do not sign up for the Internet service can view the “allowed” websites (typically hotel property
websites). The website names must be DNS-based and support the option to define wildcards. This works for client
devices with or without HTTP proxy settings.
When a user attempts to navigate to other websites, which are not in the whitelist of the walled garden profile, the
user is redirected to the login page. In addition, a blacklisted walled garden profile can also be configured to explicitly
block the unauthenticated users from accessing some websites.
Example
The following example shows the output of show walled-garden command:
White List
---------Domain Name
----------example.com
Black List
---------Domain Name
----------example2.com
The output of this command provides the following information:
Parameter
Description
Domain Name
Displays the blacklisted or whitelisted domain names and URLs.
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show walled-garden | 483
show wifi-uplink
show wifi-uplink {auth log |config | status}
Description
This command displays the configuration details, the status, and authentication log for the Wi-Fi uplinks configured
on a W-IAP.
Syntax
Parameter
Description
auth log
Displays the authentication configuration details and an authentication log.
config
Displays the Wi-Fi configuration parameters enabled on a W-IAP.
status
Displays the status of the Wi-Fi uplink.
Usage Guidelines
Use this command to view the information about status and configuration details for the Wi-Fi uplink enabled on a WIAP.
Example
show wifi-uplink auth log
The following output is displayed for the show wifi-uplink auth log command:
---------------------------------------------------------------------wifi uplink auth configuration:
------------------------------------------------------------------------------------------------------------------------------------------wifi uplink auth log:
---------------------------------------------------------------------[1536]2013-05-08 23:42:06.647: Global control interface '/tmp/supp_gbl'
show wifi-uplink config
The following output is displayed for the show wifi-uplink config command:
ESSID :Wifi
Cipher Suite :wpa-tkip-psk
Passphrase :test1234
Band :dot11a
The output for this command displays the following information:
Parameter
Description
ESSID
Displays the name of the network for which the Wi-Fi uplink is configured.
Cipher Suite
Displays the encryption settings configured for the Wi-Fi uplink. For example,
wpa-tkip-psk or wpa2-ccmp-psk.
Passphrase
Displays the WPA passphrase configured for the Wi-Fi uplink.
uplink-band <band>
Displays the band configured for the Wi-Fi uplink connection. For example,
dot11a and dot11g.
484 | show wifi-uplink
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show wifi-uplink status
The following output is displayed for the show wifi-uplink status command:
configured :YES
enabled :YES
The output of this command indicates if the Wi-Fi uplink is configured and enabled on the W-IAP.
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show wifi-uplink | 485
show wired-port
show wired-port <profile-name>
Description
This command displays the configuration details associated with a wired profile configured on a W-IAP.
Syntax
Parameter
Description
<profile-name>
Displays the current configuration details for a specific wired profile.
Usage Guidelines
Use this command to view the details of a wired profile configured on a W-IAP.
Example
The following example shows the output of the show wired-port <profile-name> command:
Name :default_wired_port_profile
VLAN Mode :Trunk
Allowed VLANs :all
Native VLAN :1
Admin Status :Down
Role :default_wired_port_profile
Speed :auto
Duplex :full
POE :No
Type :employee
Content Filtering :Disabled
Server Load Balancing :Disabled
MAC Authentication :Disabled
8021.x :Disabled
L2 Auth Fallthrough :Disabled
Captive Portal :disable
Exclude Uplink :none
Access Control Type :Network
Uplink enable :Disabled
Certificate Installed: :No
Internal Radius Users: :0
Internal Guest Users: :0
Role Derivation Rules
--------------------Attribue Operation Operand Role Name Index
-------- --------- ------- --------- ----Vlan Derivation Rules
--------------------Attribue Operation Operand Vlan Id
-------- --------- ------- ------RADIUS Servers
-------------Name IP Address Port Key Timeout Retry Count NAS IP Address NAS Identifier RFC3576
---- ---------- ---- --- ------- ----------- -------------- -------------- ------LDAP Servers
-----------Name IP Address Port Timeout Retry Count Admin-DN Admin Password Base-DN
---- ---------- ---- ------- ----------- -------- -------------- ------Access Rules
486 | show wired-port
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
-----------Dest IP Dest Mask Dest Match Protocol (id:sport:eport) Action Log TOS 802.1P Blacklist Mirror
DisScan ClassifyMedia
------- --------- ---------- ------------------------- ------ --- --- ------ --------- ------------ ------------any any match any permit
Vlan Id :0
ACL Captive Portal:disable
:Captive Portal Configuration
Background Color:13421772
Banner Color :16750848
Decoded Texts :
Banner Text :Welcome to Guest Network
Use Policy :Please read terms and conditions before using Guest Network
Terms of Use :This network is not secure, and use is at your own risk
Internal Captive Portal Redirect URL:
Captive Portal Mode:Acknowledged
Custom Logo
:External Captive Portal Configuration
Server:localhost
Port :80
URL :/
Authentication Text:Authenticated
External Captive Portal Redirect URL:
Server Fail Through:No
The output of this command shows the configuration parameters associated with the selected wired profile and the
value assigned for each of these parameters:
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show wired-port | 487
show wired-port-settings
show wired-port-settings
Description
This command displays the list of wired profiles configured on a W-IAP.
Usage Guidelines
Use this command to view the wired profiles configured on a W-IAP.
Example
The following example shows the output of show wired-port-settings command:
Wired Port Profiles
------------------Name VLAN Mode Allowed VLANs Native VLAN Admin Status Role Speed
---- --------- ------------- ----------- ------------ ---- ---wiredProf1 Access all guest Up wired-instant auto
WiredProf2 Trunk all 1 Down WiredProf2 auto
Duplex POE In Use Authentication Method
----- ----- ---- --------------------------auto Yes Yes None
full No Yes None
Port Profile Assignments
-----------------------Port Profile Name
---- -----------0 default_wired_port_profile
1 example1-crash
2 wired-instant
3 wired-instant
4 wired-instant
The output of this command provides the following information:
Column
Description
Name
Indicates the name of the wired port profile.
VLAN Mode
Indicates the name of switchport mode for the wired profiles. The VLAN modes
can be Access or Trunk.
Allowed VLAN
Indicates the list of allowed VLANs. The Allowed VLAN refers to the VLANs
carried by the port in Access mode.
Native VLAN
Indicates the values assigned for Native VLAN. A VLAN that does not have a
VLAN ID tag in the frames is referred to as Native VLAN.
Admin Status
Indicates the status of admin port.
Role
Indicates the role assigned to the wired profile users.
Speed
Indicates the speed of wired client traffic.
duplex
Indicates if the client traffic duplexing full, half, or automatically assigned based
488 | show wired-port-settings
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Column
Description
on the capabilities of the client, the AP, and the cable.
poe
Indicates if Power over Ethernet (PoE) is enabled.
In Use
Indicates if the wired profile is in use.
Authentication Method
Indicates the authentication method configured for the wired profile.
Port
Indicates the port number to which a wired profile is assigned.
Profile
Indicates the name of wired profile assigned to a wired port.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show wired-port-settings | 489
show wispr config
show wispr config
Description
This command displays the Wireless Internet Service Provider roaming (WISPr) authentication parameters
configured on a W-IAP.
Usage Guidelines
Use this command to view the WISPr configuration details for a W-IAP.
Example
The following example shows the output of show wispr config command:
WISPr
WISPr
WISPr
WISPr
WISPr
WISPr
ISO Country Code :91
E.164 Country Code :IN
E.164 Area Code :80
SSID :Network1
Operator Name :XYZ
Location Name :airport
The output of this command provides the following information:
Parameter
Description
WISPr ISO Country
Code
Indicates the ISO country code configured for WISPr authentication.
WISPr E.164 Country
Code
Indicates the E.164 Country Code for the WISPr Location ID.
WISPr E.164 Area Code
Indicates the E.164 Area Code for the WISPr Location ID.
WISPr SSID
Indicates the SSID for which the WISPr authentication profile is configured.
WISPr Operator Name
Indicates the hotspot operator profile associated with the WISPr authentication
profile.
WISPr Location Name
Indicates Hotspot location associated with the WISPr profile.
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
490 | show wispr config
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show xml-api-server
show xml-api-server config
Description
This command displays the XML API server configuration details.
Usage Guidelines
Use this command to view the XML API server configuration details.
Example
The following example shows the output of the show xml-api-server command:
ip :192.0.2.5
key :user1234
Command History
Version
Description
Dell Networking W-Series Instant
6.4.0.2-4.1
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
show xml-api-server | 491
snmp-server
snmp-server
community <string> host <ipaddr> version {1 <name> udp-port <port>}|{2c|3 <name> [inform]
[udp-port <port>]}
user <name> <auth-prot> <password> [<priv-prot> <password>
Description
This command configures SNMP parameters.
Syntax
Parameter
Description
Range
Default
community
Sets the read-only community string.
—
—
engine-id
Sets the SNMP server engine ID as a hexadecimal number.
24
characters
maximum
—
host
Configures the IP address of the host to which SNMP traps are
sent. This host needs to be running a trap receiver to receive
and interpret the traps sent by the controller.
—
—
version
Configures the SNMP version and security string for notification
messages.
—
—
inform
Sends SNMP inform messages to the configured host.
—
disabled
udp-port
Indicates the port number to which notification messages are
sent.
—
162
user
Configures an SNMPv3 user profile for the specified username.
—
—
auth-prot
Indicates the authentication protocol for the user, either HMACMD5-98 Digest Authentication Protocol (MD5) or HMAC-SHA98 Digest Authentication Protocol (SHA), and the password for
use with the designated protocol.
MD5/SHA
SHA
priv-prot
Indicate the privacy protocol for the user, either Advanced
Encryption Standard (AES) or CBC-DES Symmetric Encryption
Protocol (DES), and the password for use with the designated
protocol.
AES/DES
DES
Usage Guidelines
This command configures SNMP on the W-IAPs only.
Example
The following example configures an SNMP host and community string:
(Instant AP)(config)# snmp-server community user123
(Instant AP)(config)# snmp-server host 10.0.0.1 version 2c udp-port 162 inform
492 | snmp-server
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
snmp-server | 493
subscription-ap
subscription-ap <MAC-address> status <status>
no…
Description
This command configures the subscription status for a W-IAP.
Syntax
Command/Parameter
Description
<MAC-address>
Enter the MAC address of the W-IAP.
<status>
Enter the subscription status for the W-IAP.
no…
Removes the configuration.
Usage Guidelines
Use this command to subscribe the W-IAP based on its MAC address.
Example
(Instant AP)(config) # subscription-ap a1:b2:c3:d4:42:98 status
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
494 | subscription-ap
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
subscription-ap-enable
subscription-ap-enable
no…
Description
This command enables the subscription of a W-IAP.
Syntax
Command/Parameter
Description
subscription-ap-enable
Enables the subscription for a W-IAP.
no
Removes the configuration.
Usage Guidelines
Use this command to enable the subscription of the W-IAP.
Example
(Instant AP)(config) # subscription-ap-enable
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
subscription-ap-enable | 495
syslocation
syslocation <syslocation>
no…
Description
This command allows you to define the physical location for the W-IAP.
Syntax
Command/Parameter
Description
<syslocation>
Allows you to specify a physical location.
no
Removes the configuration.
Usage Guidelines
Use this command to define the physical location of the W-IAP.
Example
The following example sets the physical location of the W-IAP to Sunnyvale:
(Instant AP)(config) # syslocation <Sunnyvale>
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
496 | syslocation
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
syslog-level
syslog-level <level> {ap-debug|network|security|system|user|user-debug|wireless}
no...
Description
This command configures syslog facility levels. Syslog Facility is an information field associated with a syslog
message.
Syntax
Parameter
Description
Range
Default
syslog-level <level>
Configures the Syslog facility level.
Emergency,
Alert, Critical,
Errors,
Warning,
Notice,
Informational,
Debug
Notice
You can configure any of the following logging
levels:
l
l
l
l
l
l
l
l
Emergency — Panic conditions that occur
when the system becomes unusable.
Alert — Any condition requiring immediate
attention and correction.
Critical — Any critical conditions such as a
hard drive error.
Errors —Error conditions.
Warning — Warning messages.
Notice — Significant events of a non-critical
and normal nature. The default value for all
Syslog facilities.
Informational — Messages of general
interest to system users.
Debug — Messages containing information
useful for debugging.
ap-debug
Generates a log for the AP device for
debugging purposes.
—
—
network
Generates a log when there is a change in the
network, for example, when a new W-IAP is
added to a network.
—
—
security
Generates a log for network security, for
example, when a client connects using wrong
password.
—
—
system
Generates a log about the system configuration
and status.
—
—
user
Generates a log for the W-IAP clients.
—
—
user-debug
Generates a detailed log about the clients for
debugging purposes.
—
—
wireless
Generates a log about radio configuration.
—
—
no…
Removes the configuration.
—
—
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
syslog-level | 497
Usage Guidelines
Use this command to configure syslog facility levels and to generate logs based on various user and W-IAP
parameters.
Example
The following example configures syslog facility levels for ap-debug and user-debug:
(Instant AP)(config)# syslog-level error ap-debug
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
498 | syslog-level
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
syslog-server
syslog-server <IP-address>
no…
Description
This command configures Syslog server for a W-IAP.
Syntax
Parameter
Description
Range
Default
syslog-server <IPaddress>
Specifies the IP address to configure the syslog
server.
—
—
no…
Removes the configuration.
—
—
Usage Guidelines
Use this command to configure syslog server for a W-IAP.
Example
The following command configures the IP address of the syslog server for a W-IAP.
(Instant AP)(config)# syslog-server 192.0.2.9
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
syslog-server | 499
telnet-server
telnet-server
no…
Description
This command enables Telnet access to Instant command line interface (CLI).
Syntax
Command/Parameter
Description
telnet-server
Enables Telnet access to the Instant CLI.
no…
Removes the configuration
Usage Guidelines
Use this command to enable Telnet access to the Instant CLI.
Example
The following example enables Telnet access to the W-IAP:
(Instant AP)(config)# telnet-server
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.14.0
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
500 | telnet-server
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
terminal-access
terminal-access
no…
Description
This command enables Secure Shell (SSH) access to Instant CLI.
Syntax
Command/Parameter
Description
terminal-access
Enables terminal access to the Instant CLI.
no…
Removes the configuration.
Usage Guidelines
Use this command to enable SSH access to the Instant CLI.
Example
The following example enables terminal access to the W-IAP:
(Instant AP)(config)# terminal-access
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
terminal-access | 501
tftp-dump-server
tftp-dump-server <IP-address>
no…
Description
This command configures TFTP dump server for a W-IAP.
Syntax
Parameter
Description
tftp-dump-server <IP-address>
Configures TFTP dump server IP address.
no…
Removes the configuration
Usage Guidelines
Use this command to configure TFTP dump server for storing core dump files.
Example
The following example configures a TFTP dump server:
(Instant AP)(config)# tftp-dump-server <IP-address>
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
502 | tftp-dump-server
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
traceroute
traceroute <ipaddr>
Description
This command traces the route to the specified IP address.
Syntax
Parameter
Description
<ipaddr>
Displays the destination IP address.
Usage Guidelines
Use this command to identify points of failure in your network.
Example
The following example shows the output of traceroute command:
<Instant Access Point> #traceroute 10.1.2.3
Command History
Version
Description
Dell Networking W-Series
Instant 6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
traceroute | 503
upgrade-image
upgrade-image <url>
upgrade-image2 <url>
upgrade-image2-no-reboot
Description
These commands allow you to upgrade a W-IAP to use a new image file.
Syntax
Parameter
Description
upgrade-image
Upgrades the W-IAP to use a new image.
upgrade-image2
Uploads an additional image file and upgrades the W-IAP to use
this image file when required.
upgrade-image2-no-reboot
Uploads an additional image file and upgrades the W-IAP to use
the new image without rebooting the W-IAPs.
<url>
Allows you to specify the FTP, TFTP, or HTTP URL.
Usage Guidelines
Use these commands to upgrade W-IAP to use an image file uploaded from the FTP or TFTP server, or by using an
HTTP URL. Before uploading an image file, ensure that you have the appropriate image file for your W-IAP. The
following examples describe the image class for different W-IAP models:
l
l
l
l
l
For W-IAP134/135—DellInstant_Cassiopeia_<build-version>
For W-IAP108/109, W-IAP103, and W-IAP114/115—DellInstant_Pegasus_<build-version>
For W-IAP155/155P—DellInstant_Aries_<build-version>
For W-IAP224/225, and W-IAP274/275—DellInstant_Centaurus_<build-version>
For all other W-IAPs —DellInstant_Orion_<build-version>
Example
The following examples upgrade a W-IAP by using an image file from the FTP server:
(Instant AP)# upgrade-image ftp://192.0.2.7/Dell_Orion_6.2.1.0-4.0.0.0_xxxx
(Instant AP)# upgrade-image2-no-reboot ftp://192.0.2.7/Dell_Orion_6.2.1.0-4.0.0.0_xxxx
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
These commands are introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode.
504 | upgrade-image
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
uplink
uplink
enforce {ethernet| cellular |wifi | none}
failover-internet
failover-internet-check-timeout
failover-internet-pkt-lost-cnt <count>
failover-internet-pkt-send-freq <frequency>
failover-vpn-timeout <seconds>
preemption
uplink-priority {cellular <priority> | ethernet <priority>| [port <Interface-number>
<priority>]|wifi <priority>}
no…
Description
This command configures uplink connections.
Syntax
Parameter
Description
Range
Default
uplink
Enables the uplink configuration
sub-mode.
—
—
enforce {ethernet|cellular
|wifi | none}
Enforces the specified uplink
connection.
You can specify the following
types of uplink:
l ethernet
l cellular
l wifi
l none
ethernet,
cellular,
wifi,
none
None
failover-internet
Enables uplink switchover
based on the availability of the
Internet.
—
Disabled
When enabled, the W-IAP
continuously sends ICMP
packets to some well-known
Internet servers. If the request is
timed out due to a bad uplink
connection or uplink interface
failure, and the public Internet is
not reachable from the current
uplink, the W-IAP switches to a
different connection.
failover-internet-check-timeout
The number of seconds after
which the Internet based uplink
verification times out.
0-3600
10
failover-internet-pkt-lost-cnt
<count>
Configures the number of
packets that are to be lost when
verifying the uplink availability
using the Internet.
1—1000
10
failover-internet-pkt-send-freq
<frequency>
Configures the frequency in
seconds, at which the ICMP
1—3600
30
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
uplink | 505
Parameter
Description
Range
Default
packets are sent to verify the
uplink availability using the
Internet.
failover-vpn-timeout <seconds>
Configures a duration to wait for
an uplink switch based on VPN
status.
—
180
seconds
preemption
Enables pre-emption when no
uplinks are enforced. When
enabled, if the current uplink is
active, the W-IAP periodically
tries to use a higher priority
uplink, and switches to a higher
priority uplink even if the current
uplink is active.
—
Disabled
uplink-priority
{cellular <priority>|ethernet <priority>|
[port <Interface-number> <priority>]|
wifi <priority>}
Sets an uplink priority.
Integer
Eth0
no…
Removes the configuration.
—
—
You can specify the type of
uplink to configure and assign a
priority. If Ethernet uplink needs
to be prioritized, specify the
interface port number.
Usage Guidelines
Use this command to set preferences for enforcing uplinks or enabling preemption and to configure uplink
switchover.
Enforcing uplinks
The following configuration conditions apply to the uplink enforcement:
l
When an uplink is enforced, the W-IAP uses the specified uplink regardless of uplink preemption configuration
and the current uplink status.
l
When an uplink is enforced and multiple Ethernet ports are configured and uplink is enabled on the wired profiles,
the W-IAP tries to find an alternate Ethernet link based on the priority configured.
l
When no uplink is enforced and preemption is not enabled, and if the current uplink fails, the W-IAP tries to find an
available uplink based on the priority configured.
Uplink Preemption
When no uplink is enforced and preemption is enabled, and if the current uplink fails, the W-IAP tries to find an
available uplink based on in the priority configured. If current uplink is active, the W-IAP periodically tries to use a
higher priority uplink and switches to the higher priority uplink even if the current uplink is active.
Uplink Priority
When uplink priority is configured, the W-IAP tries to get a higher priority link every ten minutes even if the current
uplink is up. This does not affect the current uplink connection. If the higher uplink is usable, the W-IAP switches
over to that uplink. Preemption is enabled by default.
506 | uplink
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Uplink Switchover
The default priority for uplink switchover is Ethernet and then 3G/4G. The W-IAP has the ability to switch to the lower
priority uplink if the current uplink is down.
Uplink Switching based on VPN Status
Instant supports switching uplinks based on the VPN status when deploying mixed uplinks (Eth0, 3G/4G,Wi-Fi).
When VPN is used with multiple backhaul options, the W-IAP switches to an uplink connection based on the VPN
connection status instead of only using Eth0, the physical backhaul link.
The following configuration conditions apply to uplink switching:
l
If the current uplink is Eth0 and the VPN connection is down, the W-IAP will retry to connect to VPN. This retry
time depends on the configuration of primary/backup and fast-failover for VPN. If all the possibilities fail, then the
W-IAP waits for a vpn-failover-timeout and then a different u plink (3G,Wi-Fi) is selected.
l
If the current uplink is 3G or Wi-Fi, and Eth0 has a physical link, the W-IAP periodically suspends user traffic to
try and connect to the VPN on the Eth0. If the W-IAP succeeds, then the W-IAP switches to Eth0. If the W-IAP
does not succeed, then the W-IAP restores the VPN connection to the current uplink.
Switching Uplinks Based on Internet Availability
When the uplink switchover based on Internet availability is enabled, the W-IAP continuously sends ICMP packets
to some well-known Internet servers. If the request is timed out due to a bad uplink connection or uplink interface
failure, and the public Internet is not reachable from the current uplink, the W-IAP switches to a different connection.
Example
The following example configures uplink priority:
(Instant AP)(uplink)# uplink-priority ethernet port 0 1
(Instant AP)(uplink)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.4.0.24.1
This command is modified.
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and uplink configuration sub-mode.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
uplink | 507
uplink-vlan
uplink-vlan <vlan-ID>
Description
This command configures uplink VLAN for management traffic on a W-IAP.
Syntax
Parameter
Description
Range
Default
<vlan-ID>
Assigns a VLAN ID for the uplink
management traffic
0-4093
0
Usage Guidelines
Use this command to configure the uplink VLAN configuration details for management traffic. When configured, the
uplink management VLAN allows you to tag management traffic and connect multiple W-IAP clusters (Virtual
Controllers) to the same port on an upstream switch (for example, W-AirWave server).
Example
The following example configures uplink management VLAN:
(Instant AP)# uplink-vlan 0
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
508 | uplink-vlan
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
user
user <username> [<password>] [portal| radius]
no…
Description
This command creates users for a W-IAP.
Syntax
Parameter
Description
user <username>
Creates a username for the W-IAP user.
<password>
Assigns a password for the W-IAP user
portal
Configures a guest user.
radius
Configures an employee user
no…
Removes the configuration
Usage Guidelines
The Instant user database consists of a list of guest and employee users. Addition of a user involves specifying a
login credentials for a user. The login credentials for these users are provided outside the Instant system.
A guest user can be a visitor who is temporarily using the enterprise network to access the Internet. However, if you
do not want to allow access to the internal network and the Intranet, you can segregate the guest traffic from the
enterprise traffic by creating a guest WLAN and specifying the required authentication, encryption, and access rules.
An employee user is the employee who is using the enterprise network for official tasks. You can create Employee
WLANs, specify the required authentication, encryption and access rules and allow the employees to use the
enterprise network.
The user database is also used when a W-IAP is configured as an internal RADIUS server. The local user database
of APs can support up to 512 user entries except W-IAP-9x supports only 256 user entries. If there are already 512
users, W-IAP-9x will not be able to join the cluster.
Example
The following example configures an employee user for a W-IAP:
(Instant AP)(config)# user user1 password123 radius
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
user | 509
Command Information
510 | user
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
version
version <version-number>
Description
This command configures a version number for the W-IAP.
Syntax
Parameter
Description
version <version-number>
Assigns a version number for the W-IAP.
Usage Guidelines
Use this command to configure a version number for the W-IAP.
Example
The following example configures a version number for the W-IAP.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
version | 511
virtual-controller-country
virtual-controller-country <country-code>
no…
Description
This command configures the location of the W-IAP.
Syntax
Parameter
Description
virtual-controller-country
<country-code>
Specifies the country of operation for a W-IAP.
no…
Removes the configuration.
Usage Guidelines
Use this command to configure the country code for W-IAPs.
Example
The following example configures a country code for W-IAP:
(Instant AP)(config)# virtual-controller-country US
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
512 | virtual-controller-country
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
virtual-controller-ip
virtual-controller-ip <IP-address>
Description
This command configures an IP address for the Virtual Controller.
Syntax
Parameter
Description
virtual-controller-ip <IPaddress>
Assigns an IP address for the Virtual Controller.
Usage Guidelines
Use this command to configure an IP address for the Virtual Controller.
Example
The following example assigns an IP address for the Virtual Controller:
(Instant AP)(config)# virtual-controller-ip 192.0.2.2
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
virtual-controller-ip | 513
virtual-controller-key
virtual-controller-key <name>
Description
This command configures a unique name for the Virtual Controller.
Syntax
Parameter
Description
virtual-controller-key <name>
Defines a unique name for the Virtual Controller.
Usage Guidelines
Use this command to assign a name for the Virtual Controller.
Example
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# virtual-controller-key <name>
AP)(config)# virtual-controller-ip <IP-address>
AP)(config)# virtual-controller-vlan <Vlan-ID> <Mask> <Gateway-IP-address>
AP)(config)# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
514 | virtual-controller-key
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
virtual-controller-vlan
virtual-controller-vlan <virtual-controller-vlan> <virtual-controller-mask> <virtualcontroller-gateway>
no…
Description
This command configures a VLAN for the Virtual Controller.
Syntax
Parameter
Description
virtual-controller-vlan
<virtual-controller-vlan>
Associates a VLAN ID with the Virtual Controller.
<virtual-controller-mask>
Configures a subnet mask for the Virtual Controller.
<virtual-controllergateway>
Configures a gateway for the Virtual Controller.
no…
Removes the configuration.
Usage Guidelines
Use this command to configure VLAN, Netmask, and Gateway for the Virtual Controller.
Example
The following example configures VLAN for the Virtual Controller:
(Instant AP)(config)# virtual-controller-vlan <Vlan-ID> <Mask> <Gateway-IP-address>
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
virtual-controller-vlan | 515
vpn backup
vpn backup <name>
no…
Description
This command configures a secondary or backup VPN server for VPN connections.
Syntax
Parameter
Description
vpn backup <name>
Configures a fully qualified domain name for the secondary VPN or IPSec
endpoint.
no…
Removes the configuration.
Usage Guidelines
Use this command to configure a backup VPN server. When both primary and secondary VPN servers are
configured, the W-IAP can switch to the available VPN connection when a the primary VPN server is not available.
Example
The following example configures a backup server for VPN connections:
(Instant AP)(config)# vpn backup <name>
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
516 | vpn backup
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
vpn fast-failover
vpn fast-failover
no…
Description
This command configures fast failover feature for VPN connections.
Syntax
Parameter
Description
vpn fast-failover
Enables fast failover feature for VPN connections.
no…
Removes the configuration.
Usage Guidelines
Use this command to configure fast failover feature for VPN connections. Enabling the fast failover feature allows
the W-IAP to create a backup VPN tunnel to the controller along with the primary tunnel, and maintain both the
primary and backup tunnels separately. If the primary tunnel fails, the W-IAP can switch the data stream to the
backup tunnel. This reduces the total failover time to less than one minute.
Example
The following example configures the VPN fast failover feature:
(Instant AP)(config)# fast-failover
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
vpn fast-failover | 517
vpn gre-outside
vpn gre-outside
no…
Description
This command enables automatic configuration of the GRE tunnel between the W-IAP and the controller.
Usage Guidelines
Use this command to enable automatic configuration of the GRE tunnel between the controller to provide L2
connectivity.
Example
The following example configures an automatic GRE tunnel:
(Instant AP)(config)# vpn gre-outside
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.14.0
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
518 | vpn gre-outside
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
vpn hold-time
vpn hold-time <seconds>
no...
Description
This command configures the time interval after which the W-IAP can switch over to the primary host when
preemption is enabled.
Syntax
Parameter
Description
vpn hold-time <seconds>
Configures a time period in seconds after which the W-IAPs can switch to
primary VPN server.
no…
Removes the configuration.
Usage Guidelines
Use this command to configure a period to hold on switching to the primary server when pre-emption is enabled.
Example
The following example configures a hold-time to switch to the primary host server:
(Instant AP)(config)# hold-time <seconds>
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
vpn hold-time | 519
vpn ikepsk
vpn ikepsk <ikepsk> username <username> password <password>
no…
Description
This command configures user credentials for the VPN connection.
Syntax
Parameter
Description
vpn ikepsk <ikepsk>
Specifies an IKE authentication for VPN connection using pre-shared keys
username <username>
Defines a username that enables access to VPN.
password <password>
Defines a password that enables access to VPN.
no…
Removes the configuration.
Usage Guidelines
Use this command to configure user credentials to establish VPN connection.
Example
The following commands enable user access to VPN connection.
(Instant AP)(config)# vpn ikepsk secretKey username User1 password password123
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
520 | vpn ikepsk
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
vpn monitor-pkt-lost-cnt
vpn monitor-pkt-lost-cnt <count>
no...
Description
This command configures the number of lost packets after which the W-IAP can determine that the VPN connection
is not available.
Parameter
Description
Range
Default
vpn monitor-pkt-lost-cnt
<count>
Defines the number of lost packets for
VPN connection test or monitoring by the
W-IAP.
—
2
no…
Removes the configuration.
—
—
Usage Guidelines
Use this command to configure a count for the lost packets, so that the W-IAPs can determine if the VPN
connection is unavailable.
Example
The following example configures a count for the lost packets:
(Instant AP)(config)# vpn monitor-pkt-lost-cnt <count>
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
vpn monitor-pkt-lost-cnt | 521
vpn monitor-pkt-send-freq
vpn monitor-pkt-send-freq <frequency>
no...
Description
This command configures the frequency at which the W-IAP can verify if the active VPN connection is available.
Syntax
Parameter
Description
Range
Default
vpn monitor-pktsend-freq
<frequency>
Configures a frequency interval in seconds at
which the test packets are sent.
—
5
no…
Removes the VPN monitoring frequency
configuration.
—
—
Usage Guidelines
Use this command to monitor VPN connections and verify its availability at regular intervals.
Example
The following example configures the VPN monitoring frequency:
(Instant AP)(config)# vpn monitor-pkt-send-freq 10
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
522 | vpn monitor-pkt-send-freq
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
vpn preemption
vpn preemption
no…
Description
This command enables pre-emption to allow the VPN tunnel to switch back to the primary host after a failover.
Syntax
Parameter
Description
vpn preemption
Enables pre-emption to allow the VPN tunnel to switch to the primary VPN
server when it becomes available after a failover.
no…
Removes the VPN pre-emption configuration.
Usage Guidelines
Use this command to enable pre-emption when both primary and secondary servers are configured and fast failover
feature is enabled.
Example
The following example enables VPN pre-emption.
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
vpn preemption | 523
vpn primary
vpn primary <name>
no...
Description
This command configures a primary Virtual Private Networks (VPN) server for VPN connections.
Syntax
Parameter
Description
Range
Default
vpn primary <name>
Configures a fully qualified domain name for
the main VPN or IPSec endpoint.
—
—
no…
Removes the VPN server configuration.
—
—
Usage Guidelines
Use this command to configure a primary VPN server for IAP-VPN connections. When a secondary VPN server is
configured along with the primary server, you can enable the fast failover feature that allows the W-IAP to create a
backup VPN tunnel to the controller along with the primary tunnel, and maintain both the primary and backup tunnels
separately.
Example
The following example configures a primary VPN server:
(Instant AP)(config)# vpn primary <name>
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
524 | vpn primary
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
vpn reconnect-time-on-failover
vpn reconnect-time-on-failover <down-time>
Description
This command defines a period after which the VPN connection can be reestablished when the primary VPN tunnel
fails.
Syntax
Parameter
Description
vpn reconnect-time-on-failover
<down-time>
Configures a time period in minutes after which the VPN is
reconnected when the primary VPN tunnel fails.
Usage Guidelines
Use this command to configure a time period for reestablishing VPN connections. When configured , the W-IAP
reconnects the user session when the interval specified for this command expires.
Example
The following example configures a VPN reconnection duration:
(Instant AP)(config)# vpn reconnect-time-on-failover 20
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.4
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
vpn reconnect-time-on-failover | 525
vpn reconnect-user-on-failover
vpn reconnect-user-on-failover
no…
Description
This command enables the users to reconnect to the VPN when the primary VPN tunnel fails.
Syntax
Parameter
Description
vpn reconnect-user-onfailover
Enables users to reconnect to the VPN during a VPN failover.
no…
Removes the configuration.
Usage Guidelines
Use this command to allow the users to reconnect to the VPN after a VPN failover. When enabled , the W-IAP
reconnects the user during a VPN failover.
Example
The following example enables users to reconnect to VPN after a failover:
(Instant AP)(config)# vpn reconnect-user-on-failover
(Instant AP)(config)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.4
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
526 | vpn reconnect-user-on-failover
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
wifi0-mode
wifi0-mode <mode>
Description
This command configures a W-IAP to function in the access, monitor, or spectrum monitor mode.
Syntax
Parameter
Description
Range
Default
<mode>
Configures the W-IAP to function in any of the
following modes:
access,
monitor,
spectrummonitor
access
Access— In Access mode, the W-IAP serves
clients, while also monitoring for rogue APs
in the background.
l Monitor—In Monitor mode, the AP acts as a
dedicated monitor, scanning all channels
for rogue W-IAPs and clients.
l Spectrum Monitor— In Spectrum Monitor
mode, the W-IAP functions as a dedicated
full-spectrum RF monitor, scanning all
channels to detect interference, whether
from neighboring APs or from non-WiFi
devices such as microwaves and cordless
phones.
NOTE: In Monitor and Spectrum Monitor
modes, the W-IAP does not provide access
services to clients.
l
Usage Guidelines
Use this command to configure a Wi-Fi interface of a W-IAP to function in the access, monitor, or spectrum monitor
mode.
Example
The following example configures the wifi0 interface to use the access mode:
(Instant AP)# wifi0-mode access
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
wifi0-mode | 527
wifi1-mode
wifi1-mode <mode>
Description
This command configures a W-IAP to function in the access, monitor, or spectrum monitor mode.
Syntax
Parameter
Description
Range
Default
<mode>
Configures the W-IAP to function in any of the
following modes:
access,
monitor,
spectrummonitor
access
Access— In Access mode, the W-IAP serves
clients, while also monitoring for rogue APs
in the background.
l Monitor—In Monitor mode, the AP acts as a
dedicated monitor, scanning all channels
for rogue W-IAPs and clients.
l Spectrum Monitor— In Spectrum Monitor
mode, the W-IAP functions as a dedicated
full-spectrum RF monitor, scanning all
channels to detect interference, whether
from neighboring APs or from non-WiFi
devices such as microwaves and cordless
phones.
NOTE: In Monitor and Spectrum Monitor
modes, the W-IAP does not provide access
services to clients.
l
Usage Guidelines
Use this command to configure a Wi-Fi interface of a W-IAP to function in the access, monitor, or spectrum monitor
mode.
Example
The following example configures the wifi0 interface to use the access mode:
(Instant AP)# wifi1-mode access
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode.
528 | wifi1-mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
wired-port-profile
wired-port-profile <port>
access-rule-name <name>
allowed-vlan <vlan>
auth-server <name>
captive-portal {<type>[exclude-uplink <types>]|external[exclude-uplink <types>| profile
<name>[exclude-uplink <types>]]}
content-filtering
dot1x
duplex <duplex>
l2-auth-failthrough
mac-authentication
native-vlan <vlan>
poe
radius-reauth-interval <minutes>
server-load-balancing
set-role <attribute>{{equals|not-equal|starts-with|ends-with|contains} <operator>
<role>|value-of}
set-role-mac-auth <MAC-authentication>
set-role-machine-auth <machine-only> <user-only>
set-role-pre-auth <role>
set-role-unrestricted
set-vlan <attribute>{equals|not-equals|starts-with|ends-with|contains} <operator> <VLANID>|value-of}
shutdown
spanning-tree
speed <speed>
switchport-mode <mode>
type <type>
uplink-enable
no…
Description
This command configures a wired port profile for wired W-IAP clients.
Syntax
Command/Parameter
Description
Range
Default
wired-port-profile <port>
Creates a wired profile.
—
—
access-rule-name <name>
Maps the already configured access
rules with the wired profile.
—
—
allowed-vlan <vlan>
Configures a list of allowed VLANs. The
Allowed VLAN refers to the VLANs
carried by the port in Access mode.
—
—
—
—
You can configure the list of comma
separated digits or ranges 1,2,5 or 1-4, or
all.
auth-server <name>
Configures the authentication server for
the wired profile.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
wired-port-profile | 529
Command/Parameter
Description
Range
Default
captive-portal{<type>
[exclude-uplink <types>]
|external[exclude-uplink
<types>| profile <name>
[exclude-uplink <types>]]}
Enables internal or external captive
portal authentication for the wired profile
users.
—
—
You can also disable redirection to the
captive portal based on the type of
current uplink.
If the external captive profiles are
created, you can specify the profile name
by using the external and profile
keywords and associated parameters.
content-filtering
Enables content filtering
—
—
dot1x
Enables 802.11X authentication for the
Wired profile users
—
Disable
d
duplex <duplex>
Assigns a value for duplexing client traffic
based on the capabilities of the client, the
AP, and the cable. You can specify full,
half, or auto.
full, half, auto
auto
l2-auth-failthrough
Allows the clients to use 802.1X
authentication when MAC authentication
fails.
—
Disable
d
mac-authentication
Enables MAC authentication
—
Disable
d
native-vlan <vlan>
Configures a value for Native VLAN. A
VLAN that does not have a VLAN ID tag
in the frames is referred to as Native
VLAN.
1-4093
—
poe
Enables power over Ethernet
—
Enabled
radius-reauth-interval
<minutes>
Configures a reauthentication interval at
which all associated and authenticated
clients must be reauthenticated.
—
—
server-load-balancing
Enables load balancing across two
RADIUS servers if two authentication
servers are configured for the SSID.
—
Enabled
set-role <attribute>
{{equals| not-equal|startswith|
ends-with| contains}
operator>
<role>| value-of}
Assigns a user role to the clients. The first
rule that matches the configured
condition is applied.
—
—
You can specify any of the following
conditions:
l
l
530 | wired-port-profile
contains — The rule is applied only if
the attribute value contains the
specified string.
ends-with — The rule is applied only if
the attribute value ends with the
specified string.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command/Parameter
Description
l
l
l
l
set-role-machine-auth
<machine-only><user-only>
Range
Default
—
—
equals — The rule is applied only if the
attribute value is equal to the
specified string.
not-equals — The rule is applied only
if the attribute value is not equal to the
specified string.
starts-with — The rule is applied only if
the attribute value begins with the
specified string.
value-of - This rule sets the user role
to the value of the attribute returned.
To set a user role, the value of the
attribute must already be configured
on the W-IAP.
Configures a machine authentication
rule.
You can assign different rights to clients
based on whether their hardware device
supports machine authentication.
Machine authentication is only supported
on Windows devices, so this can be used
to distinguish between Windows devices
and other devices such as iPads.
set-role-mac-auth <maconly>
Configures a MAC authentication based
user role.
—
—
set-role-pre-auth <role>
Configures a pre-authentication role to
allow some access to the guest users
before the client authentication.
—
—
set-role-unrestricted
Configures unrestricted access control.
—
—
set-vlan <attribute>
{equals|not-equals| startswith|
ends-with| contains}
<operator>
<VLAN-ID>| value-of}
Assigns a VLAN to the clients. The first
rule that matches the configured
condition is applied.
—
—
You can specify any of the following
conditions:
l
l
l
l
l
l
contains — The rule is applied only if
the attribute value contains the
specified string.
ends-with — The rule is applied only if
the attribute value ends with the
specified string.
equals — The rule is applied only if the
attribute value is equal to the
specified string.
not-equals — The rule is applied only
if the attribute value is not equal to the
specified string.
starts-with — The rule is applied only if
the attribute value begins with the
specified string.
value-of - This rule sets the VLAN to
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
wired-port-profile | 531
Command/Parameter
Description
Range
Default
the value of the attribute returned. To
set a user role, the value of the
attribute must already be configured
on the W-IAP.
shutdown
Shuts down the admin status port
up, down
up
spanning-tree
Enables Spanning Tree Protocol on the
wired profile.
—
—
STP ensures that there are no loops in
any bridged Ethernet network and
operates on all downlink ports,
regardless of forwarding mode. STP will
not operate on the uplink port and is
supported only on W-IAPs with three or
more ports. By default Spanning Tree is
disabled on wired profiles.
speed <speed>
Assigns a value for indicating speed of
client traffic based on the capabilities of
the client, the AP, and the cable.
10,100,200, auto
auto
switchport-mode <mode>
Defines the switchport mode for the wired
profile.
access, trunk
trunk
You can specify any of the following
modes:
l Access — Use this mode to allow the
port to carry a single VLAN specified
as the native VLAN.
l Trunk — Use this mode to allow the
port to carry packets for multiple
VLANs specified as allowed VLANs.
type <type>
Defines the primary usage of the wired
profile.
employee, guest
employ
ee
uplink-enable
Enables uplink for the wired profile
—
—
no…
Removes any existing configuration
—
—
Usage Guidelines
Use this command to create a wired profile for employee and guest users. The Ethernet ports allow third-party
devices such as VoIP phones or printers (which support only wired connections) to connect to the wireless network.
You can also configure an Access Control List (ACL) for additional security on the Ethernet downlink.
Example
The following example configures a wired profile for an employee network:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
532 | wired-port-profile
AP)(config)#
AP)(wired ap
AP)(wired ap
AP)(wired ap
AP)(wired ap
AP)(wired ap
AP)(wired ap
AP)(wired ap
wired-port-profile employeeWired1
profile"employeeWired1")# type employee
profile"employeeWired1")# speed auto
profile"employeeWired1")# duplex auto
profile"employeeWired1")# no shutdown
profile"employeeWired1")# poe
profile"employeeWired1")# uplink-enable
profile"employeeWired1")# content-filtering
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
instant
(Instant
(Instant
(Instant
AP)(wired
AP)(wired
AP)(wired
AP)(wired
AP)(wired
AP)(wired
AP)(wired
AP)(wired
AP)(wired
AP)(wired
AP)(wired
ap
ap
ap
ap
ap
ap
ap
ap
ap
ap
ap
profile"employeeWired1")#
profile"employeeWired1")#
profile"employeeWired1")#
profile"employeeWired1")#
profile"employeeWired1")#
profile"employeeWired1")#
profile"employeeWired1")#
profile"employeeWired1")#
profile"employeeWired1")#
profile"employeeWired1")#
profile"employeeWired1")#
switchport-mode trunk
allowed-vlan 2,3,5
native-vlan 1
mac-authentication
dot1x
l2-auth-failthrough
auth-server server1
server-load-balancing
radius-reauth-interval 20
access-rule-name wiredACL
set-role Group-Name contains wired wired-
AP)(wired ap profile"employeeWired1")# set-vlan ap-name equals test 400
AP)(wired ap profile"employeeWired1")# end
AP)# commit apply
The following example configures a guest wired profile:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# wired-port-profile guestWired1
AP)(wired ap profile"guestWired1")# type guest
AP)(wired ap profile"guestWired1")# speed auto
AP)(wired ap profile"guestWired1")# duplex auto
AP)(wired ap profile"guestWired1")# no shutdown
AP)(wired ap profile"guestWired1")# poe
AP)(wired ap profile"guestWired1")# uplink-enable
AP)(wired ap profile"guestWired1")# content-filtering
AP)(wired ap profile"guestWired1")# switchport-mode trunk
AP)(wired ap profile"guestWired1")# allowed-vlan 200,201,400
AP)(wired ap profile"guestWired1")# native-vlan 1
AP)(wired ap profile"guestWired1")# captive-portal external exclude-uplink Ethernet
AP)(wired ap profile"guestWired1")# mac-authentication
AP)(wired ap profile"guestWired1")# auth-server server1
AP)(wired ap profile"guestWired1")# server-load-balancing
AP)(wired ap profile"guestWired1")# access-rule-name wiredACL
AP)(wired ap profile"guestWired1")# set-role Group-Name contains wired wired-instant
AP)(wired ap profile"guestWired1")# set-vlan ap-name equals test 200
AP)(wired ap profile"guestWired1")# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.14.0
This command is modified.
Dell Networking W-Series Instant 6.2.1.03.4
This command is modified.
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and Wired port profile configuration submode.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
wired-port-profile | 533
wlan access-rule
wlan access-rule <name>
bandwidth-limit {downstream <kbps>| upstream <kbps>| peruser { downstream <kbps>| upstream
<kbps>}}
calea
captive-portal {external [profile <name>]|internal}
index <index>
rule <dest> <mask> <match> {<protocol> <start-port> <end-port> {permit|deny|src-nat|dst-nat
{<IP-address> <port>| <port>}}| app <app> {permit| deny}| appcategory <appgrp>| webcategory
<webgrp> {permit| deny}| webreputation <webrep> [<option1....option9>]
vlan <vlan-id>
no…
Description
This command configures access rules for WLAN SSID or wired profile.
Syntax
Command/Parameter
Description
Range
Default
wlan access-rule <name>
Specifies the profile name for which
the access rule is configured.
—
—
bandwidth-limit {downstream
<kbps>| upstream <kbps>|
peruser {downstream
<kbps>| upstream <kbps>}}
Assign bandwidth contracts to user
roles.
The administrator can assign a
bandwidth contract configured in Kbps
to upstream (client to the W-IAP) or
downstream (W-IAP to clients) traffic for
a user role.
If you want to assign a bandwidth
contract specific for each user, you can
run the command with peruser
parameter.
The bandwidth contract will not be
applicable to the user traffic on the
bridged out (same subnet)
destinations.
NOTE: In the earlier releases,
bandwidth contract could be assigned
per SSID. In the current release, the
bandwidth contract can also be
assigned per SSID user. If the
bandwidth contract is assigned for an
SSID in Instant 6.2.1.0-3.4.0.0 image
and when the W-IAP is upgraded to
6.3.1.1-4.0 release version, the
bandwidth configuration per SSID will
be treated as per-user downstream
bandwidth contract for that SSID.
1-65535 Kbps
—
calea
Creates an access rule for CALEA
integration.
—
—
captive-portal
{external [profile <name>]
|internal}
Configures a captive-portal role, to
assign to the users role after a
successful authentication.
—
—
<index>
Creates an index entry for access
—
—
534 | wlan access-rule
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command/Parameter
Description
Range
Default
—
—
rules.
rule
Creates an access rule.
You can create up to 128 access
control entries in an ACL for a user
role. However, it is recommended to
delete any existing configuration and
apply changes at regular intervals.
<dest>
Allows you to specify the destination IP
address.
—
—
<mask>
Specifies the subnet mask for the
destination IP address.
—
—
<match>
l
match—Indicates if the rule specific
to the destination IP address and
subnet mask matches the value
specified for protocol.
invert— Indicates if the rule allows
or denies traffic with an exception
to the specified destination IP
address and subnet mask.
match
—
Configures any of the following:
Protocol number between 0-255
l any: any protocol
l tcp: Transmission Control Protocol
l udp: User Datagram Protocol
1-255
—
<sport>
Specifies the starting port number from
which the rule applies.
1-65534
—
<eport>
Specifies the ending port number until
which the rule applies
1-65534
—
dst-nat
Allows the W-IAP to perform
destination NAT on packets.
—
—
src-nat
Allows the W-IAP to perform source
NAT on packets. When configured, the
source IP changes to the outgoing
interface IP address (implied NAT
pool) or from the pool configured
(manual NAT pool).
—
—
<dst-nat-IP-address>
Specifies the destination NAT IP
address for the specified packets when
dst-nat action is configured.
—
—
<dst-nat-port>
Specifies the destination NAT port for
the specified packets when dst-nat
action is configured.
—
—
app <app>
Specifies a rule to allow or deny
access to a specific type of application.
To view the list
—
l
<protocol>
invert
l
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
wlan access-rule | 535
Command/Parameter
Description
Range
Default
of applications,
run the show dpi
app all
command.
appcategory <appgrp>
Specifies a rule to allow or deny
access to a specific category of
application.
To view the list
of application
categories, run
the show dpi
appcategory all
command.
—
webcategory <webgrp>
Specifies a rule to allow or deny
access to websites based on website
category.
To view the list
of website
categories, run
the show dpi
webcategory all
command.
—
webreputation <webrep>
Specifies a rule to allow or deny
access to websites based on security
rating.
l
trustworthysites
low-risk-sites
moderaterisk-sites
suspicioussites
high-risksites
—
l
l
l
l
permit
Creates a rule to allow the specified
packets.
—
—
deny
Creates a rule to reject the specified
packets
—
—
Allows you to specify any of the
following options:
—
—
<option1…option9>
l
l
l
l
l
l
l
536 | wlan access-rule
Log —Creates a log entry when this
rule is triggered.
Blacklist — Blacklists the client
when this rule is triggered.
Classify-media — Performs a packet
inspection on all non-NAT traffic
and marks the critical traffic.
Disable-scanning — Disables ARM
scanning when this rule is
triggered.
DSCP tag — Specifies a DSCP
value to prioritize traffic when this
rule is triggered.
802.1p priority — Sets an 802.1p
priority.
Application throttling: To set a
bandwidth limit based on
application, application category,
web category or website reputation,
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command/Parameter
Description
Range
Default
you can configure application
throttling by using the throttledownstream and throttle-up
options. For example, you can limit
the bandwidth rate for video
streaming applications such as
Youtube or Netflix, or set a low
bandwidth for suspicious websites.
vlan <vlan-id>
Configures an access rule for VLAN
assignment.
1-4093
—
no…
Removes the configuration
—
—
Usage Guidelines
Use this command to configure access rules for user roles, to create a captive-portal role, and to assign VLANs for
the clients.
If TCP and UDP uses the same port, ensure that you configure separate access rules to permit or deny access.
Example
The following example configures access rules for the wireless network:
(Instant AP)(config)# wlan access-rule WirelessRule
(Instant AP)(Access Rule "WirelessRule")# rule 192.0.2.2 255.255.255.0 match 6 4343 4343 log
classify-media
(Instant AP)(Access Rule "WirelessRule")# rule 192.0.2.2 255.255.255.0 192.0.2.7 255.255.255.0
match tcp 21 21 deny
(Instant AP)(Access Rule "WirelessRule")# rule 192.0.2.2 255.255.255.0 192.0.2.7 255.255.255.0
match udp 21 21 deny
(Instant AP)(Access Rule "WirelessRule")# rule any any match app youtube permit throttledownstream 256 throttle-up 256
(Instant AP)(Access Rule "WirelessRule")# rule any any match appcategory webmail permit
throttle-downstream 256 throttle-up 256
(Instant AP)(Access Rule "WirelessRule")# rule any any match webcategory gambling deny
(Instant AP)(Access Rule "WirelessRule")# rule any any match webcategory training-and-tools
permit
(Instant AP)(Access Rule "WirelessRule")# rule any any match webreputation high-risk-sites
deny
(Instant AP)(Access Rule "WirelessRule")# end
(Instant AP)# commit apply
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
wlan access-rule | 537
Command History
Version
Description
Dell Networking W-Series Instant 6.4.0.24.1
This command is modified.
Dell Networking W-Series Instant 6.3.1.14.0
This command is modified.
Dell Networking W-Series Instant 6.2.1.03.4
This command is modified.
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and access rule configuration sub-mode.
538 | wlan access-rule
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
wlan auth-server
wlan auth-server <auth_profile_name>
acctport <accounting-port>
cppm-rfc3576-only
cppm-rfc3576-port <rfc3576-port>
deadtime <time>
drp-ip <IP-address> <mask> vlan <vlan> gateway <gateway-IP-address>
ip <IP-address>
key <key>
nas-id <NAS-ID>
nas-ip <IP-address>
port <port-name>
retry-count <count>
rfc3576
timeout <seconds>
no…
Description
This command configures an external RADIUS and CPPM server for user authentication.
Syntax
Command/Parameter
Description
Range
Default
wlan auth-server <serverprofile>
Configures the external RADIUS server
authentication profile.
—
—
acctport <accounting-port>
Configures the accounting port number
used for sending accounting records to
the RADIUS server.
—
1813
cppm-rfc3576-only
Configures a CPPM server used for
AirGroup CoA (Change of
Authorization) with RFC3576 only.
—
—
The CPPM server acts as a RADIUS
server and asynchronously provides
the Air Group parameters for the client
device, including shared user, shared
role and shared location.
cppm-rfc3576-port <rfc3576port>
Configures the port number for sending
AirGroup CoA, instead of the standard
CoA port.
—
5999
deadtime <time>
Configures a dead time interval for the
authentication server.
1—1440
minutes
5
—
—
When two or more authentication
servers are configured on the W-IAP
and a server is unavailable, the dead
time configuration determines the
duration for which the authentication
server would be available if the server
is marked as unavailable.
drp-ip <IP-address> <mask>
vlan <vlan> gateway <gateway-
Configures the IP address, net mask
and VLAN, which will be used as
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
wlan auth-server | 539
Command/Parameter
Description
IP-address>
source address and VLAN for
RADIUS packets.
Range
Default
NOTE: Before configuring DRP IP
address, ensure that dynamic RADIUS
proxy is enabled, and a static Virtual
Controller IP is configured.
ip <IP-address>
Configures the IP address of the
RADIUS server
—
—
key <key>
Configures a shared key
communicating with the external
RADIUS server.
—
—
nas-id <NAS-ID>
Configures Network Attached Storage
(NAS) identifier strings for RADIUS
attribute 32, which is sent with RADIUS
requests to the RADIUS server.
—
—
nas-ip <IP-address>
Configures the Virtual Controller IP
address as the NAS address which is
sent in data packets.
—
—
port <port-name>
Configures the authorization port
number of the external RADIUS server.
—
1812
retry-count <count>
Configures the maximum number of
authentication requests that can be sent
to the server group.
1-5
3
rfc3576
Allows the W-IAPs to process RFC
3576-compliant Change of
Authorization (CoA) and disconnect
messages from the RADIUS server.
Disconnect messages cause a user
session to be terminated immediately,
whereas the CoA messages modify
session authorization attributes such as
data filters.
—
Disabled
timeout <seconds>
Configures a timeout value in second to
determine when a RADIUS request
must expire.
1 to 30
seconds
5
—
—
The W-IAP retries to send the request
several times (as configured in the
Retry count), before the user gets
disconnected. For example, if the
Timeout is 5 seconds, Retry counter is
3, user is disconnected after 20
seconds.
no…
540 | wlan auth-server
Removes the configuration.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Usage Guidelines
Use this command to configure an external RADIUS server and a CPPM server as a RADIUS server for AirGroup
Change of Authorization (CoA) requests.
Example
The following example configures the external RADIUS server parameters:
(Instant AP)(config)# wlan auth-server RADIUS1
(Instant AP)(Auth Server <RADIUS1>)# ip 192.0.0.5
(Instant AP)(Auth Server <RADIUS1>)# key SecretKey
(Instant AP)(Auth Server <RADIUS1>)# port 1812
(Instant AP)(Auth Server <RADIUS1>)# acctport 1813
(Instant AP)(Auth Server <RADIUS1>)# no nas-id
(Instant AP)(Auth Server <RADIUS1>)# no nas-ip
(Instant AP)(Auth Server <RADIUS1>)# drp-ip 192.0.2.11 255.255.255.255 vlan 200 gateway
192.0.2.15
(Instant AP)(Auth Server <RADIUS1>)# timeout 10
(Instant AP)(Auth Server <RADIUS1>)# retry-count 3
(Instant AP)(Auth Server <RADIUS1>)# end
(Instant AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.14.0
This command is modified.
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and authentication server profile sub-mode.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
wlan auth-server | 541
wlan captive-portal
wlan captive-portal
authenticated
background-color <background-color>
banner-color <banner-color>
banner-text <banner-text>
custom-logo <name>
decoded-texts <decoded-text>
redirect-url <url>
terms-of-use <terms-of-use-text>
use-policy <policy-text>
no…
Description
This command customizes the appearance of the internal captive portal splash page of the guest users.
Syntax
Command/Parameter
Description
Range
Default
wlan captive-portal
Displays the sub-mode for configuring
internal captive portal splash page.
—
—
authenticated
Configures the authentication text. The
authenticated text is used for indicating
that the authentication mode is enabled
for the internal Captive Portal users.
When the authentication mode is
enabled, the W-IAP displays a splash
page that requires the guest users to
enter their credentials. The users
allowed to access the Internet only if
they complete the authentication
successfully.
—
—
background-color
<background-color>
Configures the color code for the
internal captive portal splash page.
Web color codes
134217772
banner-color <bannercolor>
Configures the color code for the banner
on the splash page.
Web color codes
16750848
banner-text <bannertext>
Configures the text displayed on splash
page banner
Text string not
exceeding 127
characters
Welcome to
Guest Network
custom-logo
Allows you to save the customized logo
to the internal captive portal server.
—
—
decoded-texts
<decoded-text>
Displays decoded texts.
—
—
redirect-url <url>
Configures a URL to redirect the users
after a successful authentication.
—
—
NOTE: By default, after entering the
requested info at the splash page, the
users are redirected to the URL that was
542 | wlan captive-portal
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command/Parameter
Description
Range
Default
originally requested. When a URL is
configured for redirection, it overrides
the user’s original request and redirects
them to URL configured for redirection.
terms-of-use <termsof-use-text>
Defines the terms and conditions that
the user must be aware of.
Text string
This network is
not secure, and
use is at your
own risk
use-policy <policytext>
Configures usage policy text for splash
page.
Text string
Please read
terms and
conditions
before using
Guest Network
no…
Removes the configuration.
—
—
Usage Guidelines
Use this command to customize the appearance of internal captive portal splash page for the guest users.
Example
The following example configures the contents of the internal captive portal splash page:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
risk"
(Instant
Network"
(Instant
(Instant
AP)(config)# wlan captive-portal
AP)(Captive Portal)# authenticated
AP)(Captive Portal)# background-color 13421772
AP)(Captive Portal)# banner-color 16750848
AP)(Captive Portal)# banner-text "Welcome to Guest Network"
AP)(Captive Portal)# no decoded-texts
AP)(Captive Portal)# redirect-url example1.com
AP)(Captive Portal)# terms-of-use "This network is not secure, and use is at your own
AP)(Captive Portal)# use-policy "Please read terms and conditions before using Guest
AP)(Captive Portal)# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.14.0
This command is modified.
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and captive portal sub-mode.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
wlan captive-portal | 543
wlan external-captive-portal
wlan external-captive-portal [profile-name]
auth-text <text>
auto-whitelist-disable
https
port <port>
redirect-url <redirection-url>
server <server-name>
server-fail-through
url <url>
no…
Description
This command configures profiles for external captive portal.
Syntax
Command/Parameter
Description
Range
Default
wlan external-captiveportal [profile-name]
Creates an external captive portal profile.
—
—
auth-text <text>
Configures the authentication text to be
returned by the external server.
—
—
You can create multiple external captive
portal profiles and apply to an SSID or a
wired profile.
The authentication text command
configuration is required only for the
External - Authentication Text splash mode.
auto-whitelist-disable
Disables automatic whitelisting of URLs.
—
Enabled
https
Enables HTTPS for client connections.
—
—
Port <port>
Configures the port to use for
communication with the external captive
portal server.
—
80
redirect-url
<redirection-url>
Configures a URL to redirect the users after
a successful authentication.
—
—
NOTE: By default, after entering the
requested info at the splash page, the users
are redirected to the URL that was originally
requested. When a URL is configured for
redirection, it overrides the user’s original
request and redirects them to URL
configured for redirection.
server <server-name>
Configures the external captive portal
server.
—
—
url <url>
Configures the URL of the external captive
portal server.
—
—
server-fail-through
Allows the guest clients to access the
—
Disabled
544 | wlan external-captive-portal
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command/Parameter
Description
Range
Default
—
—
Internet when the external captive portal
server is not available.
Removes the configuration.
no…
Usage Guidelines
Use this command to configure external captive portal profiles for guest users. When the captive portal profile is
applied to an SSID or a wired profile, the users connecting to the SSID or wired network are assigned a role with the
captive portal rule. You can create up to 8 external captive portal profiles.
Example
The following example configures external captive portal splash page:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# wlan external-captive-portal
AP)(External Captive Portal "AuthText1")#
AP)(External Captive Portal "AuthText1")#
AP)(External Captive Portal "AuthText1")#
AP)(External Captive Portal "AuthText1")#
AP)(External Captive Portal "AuthText1")#
AP)(External Captive Portal "AuthText1")#
AP)(External Captive Portal "AuthText1")#
AP)(External Captive Portal "AuthText1")#
AP)# commit apply
AuthText1
auth-text authenticated
port 80
redirect-url http://www.example1.com
server CPServer1
url "/example.php"
server-fail-through
no auto-whitelist-disable
end
Command History
Version
Description
Dell Networking W-Series Instant 6.3.1.14.0
This command is modified.
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and external captive portal sub-mode.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
wlan external-captive-portal | 545
wlan ldap-server
wlan ldap-server <server-name>
admin-dn <domain-name>
admin-password <password>
base-dn <base_domain-name>
deadtime <time>
filter <filter>
key-attribute <key-attribute>
ip <IP-address>
port <port-name>
timeout <seconds>
retry-count <count>
no...
Description
This command configures a Lightweight Directory Access Protocol (LDAP) server for user authentication on the
Virtual Controller.
Syntax
Command/Parameter
Description
Range
Default
wlan ldap-server <server-name>
Configures an LDAP authentication
server.
—
—
admin-dn <domain-name>
Configures a distinguished name for
the administrator with read and
search privileges across all the
entries in the LDAP database.
The user need not have write
privileges, but the user must be able
to search the database, and read
attributes of other users in the
database.
—
—
admin-password <password>
Configures a password for
administrator.
—
—
base-dn <base-domain-name>
Configures a distinguished name for
the node which contains the entire
user database.
—
—
deadtime <time>
Configures a dead time interval for
the authentication server.
1—1440
minutes
5
strings
(objectclass=*)
When two or more authentication
servers are configured on the W-IAP
and a server is unavailable, the dead
time configuration determines the
duration for which the authentication
server would be available if the server
is marked as unavailable.
filter <filter>
546 | wlan ldap-server
Configures the filter to apply when
searching for a user in the LDAP
database.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command/Parameter
Description
Range
Default
key-attribute <key-attribute>
Configures the attribute to use as a
key when searching for the LDAP
server.
For Active Directory, the value is
sAMAccountName
—
—
ip <IP-address>
Configures the IP address of the
LDAP server.
—
—
port <port>
Configures the authorization port
number of the LDAP server.
—
389
timeout <seconds>
Configures a timeout value for LDAP
requests from the clients
1-30
seconds
5
retry-count <count>
Defines the number of times that the
clients can attempt to connect to the
server.
1-5
3
no…
Removes the configuration.
—
—
Usage Guidelines
Use this command to configure an LDAP server as an external authentication server. The LDAP service is based on
a client-server model. The W-IAP client requests for an LDAP session after connecting to the LDAP server and
server sends its responses.
Example
The following example configures an LDAP server:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# wlan ldap-server Server1
AP)(LDAP Server <name>)# ip 192.0.1.5
AP)(LDAP Server <name>)# port 389
AP)(LDAP Server <name>)# admin-dn cn=admin
AP)(LDAP Server <name>)# admin-password password123
AP)(LDAP Server <name>)# base-dn dc=example, dc=com
AP)(LDAP Server <name>)# filter (objectclass=*)
AP)(LDAP Server <name>)# key-attribute sAMAccountName
AP)(LDAP Server <name>)# timeout 5
AP)(LDAP Server <name>)# retry-count 3
AP)(LDAP Server <name>)# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and LDAP server sub-mode.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
wlan ldap-server | 547
wlan ssid-profile
wlan ssid-profile <ssid_profile>
a-max-tx-rate <rate>
a-min-tx-rate <rate>
air-time-limit <limit>
auth-server <name>
auth-survivability
bandwidth-limit <limit>
blacklist
broadcast-filter <type>
captive-portal {<type>[exclude-uplink <types>]|external[exclude-uplink <types>| profile
<name>[exclude-uplink <types>]]}
content-filtering
deny-inter-user-bridging
deny-local-routing
disable
dmo-channel-utilization-threshold <threshold>
dot11k
dot11r
dot11v
dtim-period <value>
dynamic-multicast-optimization
enable
enforce-dhcp
essid <essid>
external-server
g-min-tx-rate <rate>
g-max-tx-rate <rate>
hide-ssid
hotspot-profile <name>
inactivity-timeout <interval>
index <idx>
key-duration <duration>
l2-auth-failthrough
leap-use-session-key
local-probe-req-thresh <threshold>
mac-authentication
mac-authentication-delimiter <delim>
mac-authentication-upper-case
max-authentication-failures <limit>
max-clients-threshold <Max_clients>
multicast-rate-optimization
okc-disable
opmode <opmode>
per-user-bandwidth-limit <limit>
radius-accounting
radius-accounting-mode {user-association|user-authentication}
radius-interim-accounting-interval <minutes>
radius-reauth-interval <minutes>
rf-band <band>
server-load-balancing
set-role <attribute> {{contains|ends-with|equals|matches-regular-expression|notequals|starts-with} <operand> <role>|value-of}
set-role-by-ssid
set-role-mac-auth <mac_only>
set-role-machine-auth {<machine-only>|<user-only>}
set-role-pre-auth <role>
set-role-unrestricted
set-vlan <attribute> {{contains|ends-with|equals|matches-regular-expression|notequals|starts-with} <operand> <vlan>|value-of}
termination
548 | wlan ssid-profile
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
type {employee|voice|guest}
vlan <vlan>
wep-key <wep-key>
wispr
wmm-background-dscp <dscp>
wmm-background-share <share>
wmm-best-effort-dscp <dscp>
wmm-best-effort-share <share>
wmm-video-dscp <dscp>
wmm-video-share <share>
wmm-voice-dscp <dscp>
wmm-voice-share <share>
work-without-uplink
wpa-passphrase <wpa-passphrase>
zone <zone>
no…
Description
This command configures a WLAN SSID profile.
Syntax
Command/Parameter
Description
Range
Default
wlan ssid-profile <ssid_
profile>
Creates a WLAN SSID profile.
—
—
a-max-tx-rate <rate>
Configures the specify the
maximum transmission rate for the
5 GHz band.
6-54 Mbps
54 Mbps
a-min-tx-rate <rate>
Configures the specify the
minimum transmission rate for the
5 GHz band.
6-54 Mbps
6 Mbps
air-time-limit <limit>
Configures an aggregate amount
of airtime that all clients using this
SSID can use for sending and
receiving data.
—
—
auth-server <name>
Configures an authentication
server for the SSID users.
—
—
auth-survivability
Enables the authentication
survivability feature.
NOTE: The authentication
survivability feature requires
ClearPass Policy Manager 6.0.2 or
later, and is applicable only when
external servers such as RADIUS
are configured for the SSID. When
enabled, Instant authenticates the
previously connected clients using
EAP-PEAP authentication even
when connectivity to ClearPass
Policy Manager is temporarily lost.
The Authentication survivability
feature is not applicable when a
RADIUS server is configured as an
—
—
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
wlan ssid-profile | 549
Command/Parameter
Description
Range
Default
internal server.
bandwidth-limit
<limit>
Configures an aggregate amount
of bandwidth that each radio is
allowed to provide for the
connected clients.
1—65535
—
blacklist
Enables dynamic blacklisting of
clients.
—
—
broadcast-filter <type>
Configures broadcast filtering
parameters:
You can configure any of the
following filtering parameters:
l All—When set to All, the W-IAP
drops all broadcast and
multicast frames except DHCP
and ARP.
l ARP—When set to ARP, the WIAP converts ARP requests to
unicast and send frames
directly to the associated client.
l Disabled— When set to
Disabled, all broadcast and
multicast traffic is forwarded.
All, ARP,
Disabled
Disabled
captive-portal
{<type>[exclude-uplink <types>]
|external[exclude-uplink
<types>|
profile <name>[exclude-uplink
<types>]]}
Configures captive portal
authentication for the SSID.
—
—
You can also exclude an uplink
type for the captive portal based
SSID profiles. When an uplink type
is selected for the exclude-uplink
option, redirection to the captive
portal based on the type of
specified uplink is disabled.
3G,4G,
wifi,ethernet
—
content-filtering
Routes all DNS requests for the
non-corporate domains to
OpenDNS on this network.
—
Disabled
deny-inter-user-bridging
Disables the bridging traffic
between two clients connected to
the same SSID on the same VLAN.
When inter-user bridging is
disabled, the clients can connect to
the Internet, but cannot
communicate with each other, and
the bridging traffic between the
clients is sent to the upstream
device to make the forwarding
—
—
550 | wlan ssid-profile
If the external captive profiles are
created, you can specify the profile
name by using the external and
profile keywords and associated
parameters.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command/Parameter
Description
Range
Default
decision.
deny-local-routing
Disables the routing traffic
between two clients connected to
the same SSID on different VLANs.
When local routing is disabled, the
clients can connect to the Internet,
but cannot communicate with each
other, and the routing traffic
between the clients is sent to the
upstream device to make the
forwarding decision.
—
—
disable
Disables the SSID. By default all
SSIDs are enabled.
—
—
dmo-channel-utilizationthreshold
<threshold>
Sets a threshold for DMO channel
utilization. W-IAP sends multicast
traffic over the wireless link.
1–100
percentage
value
90
dot11k
Enables 802.11k roaming on the
SSID profile.
—
—
—
—
The 802.11k protocol enables WIAPs and clients to dynamically
measure the available radio
resources.
When 802.11k is enabled, W-IAPs
and clients send neighbor reports,
beacon reports, and link
measurement reports to each
other.
dot11r
Enables 802.11r on the SSID
profile.
802.11r or fast BSS transition (FT)
is an IEEE standard that permits
continuous connectivity across
wireless devices during client
mobility. Fast BSS Transition
mechanism minimizes the
delay in roaming when a client
transitions from one BSS to
another within the
same cluster.
Fast BSS Transition is operational
only if the wireless client supports
802.11r standard. If the client does
support 802.11r standard, it falls
back to normal WPA2
authentication method.
dot11v
Enables 802.11v based BSS
transition.
—
—
dtim-period <value>
Configures the Delivery Traffic
Indication Message (DTIM) interval
1–10
beacons
1
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
wlan ssid-profile | 551
Command/Parameter
Description
Range
Default
—
Disabled
for the SSID profile.
The DTIM interval determines how
often the W-IAP should deliver the
buffered broadcast and multicast
frames to associated clients in the
powersaving mode.
When configured, the client checks
for buffered data on the W-IAP at
the specified number of beacons.
You can also configure a higher
value for DTIM interval for power
saving.
dynamic-multicast-optimization
Allows the W-IAP to convert
multicast streams into unicast
streams over the wireless link.
Enabling Dynamic Multicast
Optimization (DMO) enhances the
quality and reliability of streaming
video, while preserving the
bandwidth available to the nonvideo clients.
NOTE: When you enable DMO on
multicast SSID profiles, ensure that
the DMO feature is enabled on all
SSIDs configured in the same
VLAN.
enable
Re-enables the deactivated SSIDs.
—
Enabled
enforce-dhcp
Enforces dynamic VLAN
assignment for clients from the
DHCP server.
—
Disabled
essid <essid>
Defines a name that uniquely
identifies a wireless network.
—
—
external-server
Configures an external RADIUS
server for authentication.
—
—
g-min-tx-rate <rate>
Configures the specify the
minimum transmission rate for the
2.4 GHz band.
1-54 Mbps
1 Mbps
g-max-tx-rate <rate>
Configures the specify the
maximum transmission rate for the
2.4 GHz band.
1-54 Mbps
54 Mbps
hide-ssid
Hides the SSID. When enabled,
the SSID will not be visible for the
users.
—
Disabled
hotspot-profile <name>
Associates a hotspot profile with
the WLAN SSID profile.
—
—
552 | wlan ssid-profile
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command/Parameter
Description
Range
Default
inactivity-timeout <interval>
Configures a timeout value for the
inactive client sessions.
60-86400
seconds
1000
When a client session is inactive
for the specified duration, the
session expires and the clients are
required to log in again.
index <idx>
Assigns an index value for the
SSID.
—
—
l2-auth-failthrough
Allows the clients to use 802.1X
authentication when MAC
authentication fails.
—
Disabled
leap-use-session-key
Allows the users to derive session
keys for Lightweight Extensible
Authentication Protocol (LEAP)
authentication.
—
Disabled
0-100 dB
—
Configure this command for old
printers that use dynamic WEP and
if you do not want use a session
key from the RADIUS Server to
derive pair wise unicast keys.
local-probe-req-thresh
<threshold>
Configures a Received signal
strength indication (RSSI)
threshold value to limit the number
of incoming probe requests.
When enabled, this command
controls the system response to
the broadcast probe requests sent
by clients to search for the
available SSIDs and ignores the
probe request if required,
mac-authentication
Enables MAC authentication for
clients that use this SSID profile.
—
Disabled
mac-authentication-delimiter
<delim>
Allows you to set a delimiter that
can be used in the MAC address
string for MAC authentication.
colon or
dash
—
—
—
You can specify colon or dash for
delimiter. If the delimiter is not
specified, the MAC address in the
xxxxxxxxxxxx format is used. If you
specify colon for the delimiter, the
MAC addresses in the
xx:xx:xx:xx:xx:xx format are used.
mac-authentication-upper-case
Enables the W-IAP to use
uppercase letters in MAC address
string for MAC authentication.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
wlan ssid-profile | 553
Command/Parameter
Description
Range
Default
max-authentication-failures
<limit>
Configures the maximum number
of authentication failures to
dynamically blacklist the users.
—
—
The users who exceed the number
of authentication failures
configured through this command
are dynamically blacklisted.
max-clients-threshold
<threshold>
Configures the maximum number
of clients for a BSSID on a WLAN.
0-255
64
multicast-rate-optimization
Allows the W-IAP to select the
optimal rate for sending broadcast
and multicast frames based on the
lowest of unicast rates across all
associated clients.
—
Disabled
—
—
opensystem,
wpa2-aes,
wpa2-pskaes, wpatkip, wpapsk-tkip,
wpa-tkip
wpa2-aes,
wpa-psk-tkip
wpa2-pskaes, staticwep,
dynamic-wep
opensystem
When enabled, the multicast traffic
can be sent at the rate of 1-24
Mbps. The default rate for sending
frames for 2.4 GHz is 1 Mbps and
5.0 GHz is 6 Mbps.
okc-disable
Disables opportunistic key caching
(OKC).
In the OKC based roaming, the AP
stores one pairwise master key
(PMK) per client, which is derived
from last 802.1X authentication
completed by the client in the
network. The cached PMK is used
when a client roams to a new WIAP to allow faster roaming of
clients.
NOTE: If the wireless client (the
802.1X supplicant) does not
support this feature, a complete
802.1X authentication is required
whenever it roams to a new W-IAP.
OKC is supported on WPA2-AES
Enterprise network only.
opmode <opmode>
554 | wlan ssid-profile
Configures the layer-2
authentication and encryption for
this SSID to protect access and
ensure the privacy of the data
transmitted to and from the
network.
You can configure any of the
following types of encryption:
l opensystem — No
authentication and encryption.
l wpa2-aes —WPA2 with AES
encryption and dynamic keys
using 802.1x.
l wpa2-psk-aes — WPA2 with
AES encryption using a
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command/Parameter
Description
l
l
l
l
l
l
per-user-bandwidth-limit
<limit>
Range
Default
1—65535
Kbps
—
—
Disabled
—
userauthenticatio
n
Any integer
value in
minutes
—
preshared key.
wpa-tkip — WPA with TKIP
encryption and dynamic keys
using 802.1x.
wpa-psk-tkip — WPA with TKIP
encryption using a pre-shared
key.
wpa-tkip, wpa2-aes — WPA with
TKIP and WPA2 with AES
encryption.
wpa-psk-tkip,wpa2-psk-aes WPS with TKIP and WPA2 with
AES encryption using a preshared key.
static-wep — WEP with static
keys.
dynamic-wep — WEP with
dynamic keys.
Configures a bandwidth limit in
Kbps for the SSID users.
NOTE: The bandwidth contracts
can also be applied per SSID user.
radius-accounting
Enables accounting for the
RADIUS server authentication.
When enabled, the W-IAPs post
accounting information to the
Radius server at the specified
accounting interval.
radius-accounting-mode
{user-association|userauthentication}
Configures an accounting mode
for the captive portal users.
You can configure any of the
following modes for accounting:
l
l
radius-interim-accountinginterval
<minutes>
user-authentication — when
configured, the accounting
starts only after client
authentication is successful
and stops when the client logs
out of the network.
user-association — When
configured, the accounting
starts when the client
associates to the network
successfully and stops when
the client is disconnected.
Configures an interval for posting
accounting information as RADIUS
INTERIM accounting records to the
RADIUS server.
When configured, the W-IAP sends
interim-update messages with
current user statistics to the
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
wlan ssid-profile | 555
Command/Parameter
Description
Range
Default
RADIUS server at regular intervals.
radius-reauth-interval
<minutes>
Configures an interval at which WIAPs can periodically
reauthenticate all associated and
authenticated clients.
Any integer
value in
minutes
—
rf-band <band>
Configures the radio frequency
band on which this SSID will be
broadcast. You can select either
2.4GHz, 5 GHz, or all to specify
both bands.
2.4 GHz, 5
GHz, all
all
server-load-balancing
Enables load balancing across two
RADIUS servers if two
authentication servers are
configured for the SSID.
—
Enabled
set-role{{contains|ends-with|
equals|matches-regularexpression|
not-equals|starts-with}
<operand> <role>|value-of}
Assigns a user role to the clients.
The first rule that matches the
configured condition is applied.
—
—
—
—
You can set any of the following
conditions:
l
l
l
l
l
l
l
set-role-by-ssid
556 | wlan ssid-profile
contains — The rule is applied
only if the attribute value
contains the specified string.
ends-with — The rule is applied
only if the attribute value ends
with the specified string.
equals — The rule is applied
only if the attribute value is
equal to the specified string.
not-equals — The rule is
applied only if the attribute
value is not equal to the
specified string.
starts-with — The rule is applied
only if the attribute value
begins with the specified string.
value-of - This rule sets the
user role to the value of the
attribute returned. To set a user
role, the value of the attribute
must already be configured on
the W-IAP.
matches-regular-expression —
The rule is applied only if the
attribute value matches the
regular expression pattern
specified in Operand. This
operator is available only if the
mac-address-and-dhcpoptions attribute is selected in
the Attribute drop-down.
Configures a user role based on
the type of SSID configured.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command/Parameter
Description
Range
Default
set-role-mac-auth <mac-only>
Configures a MAC authentication
based user role.
—
—
set-role-machine-auth
<machine-only>
<user-only>
Configures a machine
authentication rule.
—
—
You can assign different rights to
clients based on whether their
hardware device supports
machine authentication.
Machine authentication is only
supported on Windows devices, so
this can be used to distinguish
between Windows devices and
other devices such as iPads.
set-role-pre-auth <role>
Configures a pre-authentication
role to allow some access to the
guest users before the client
authentication.
—
—
set-role-unrestricted
Configures unrestricted access
control.
—
—
set-vlan <attribute>
{{contains|ends-with|
equals|matches-regularexpression|
not-equals|starts-with}
<operand> <vlan>|value-of}
Assigns a VLAN to the clients. The
first rule that matches the
configured condition is applied.
—
—
You can specify any of the
following conditions:
l
l
l
l
l
l
l
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
contains — The rule is applied
only if the attribute value
contains the specified string.
ends-with — The rule is applied
only if the attribute value ends
with the specified string.
equals — The rule is applied
only if the attribute value is
equal to the specified string.
not-equals — The rule is
applied only if the attribute
value is not equal to the
specified string.
starts-with — The rule is applied
only if the attribute value
begins with the specified string.
value-of - This rule sets the
VLAN to the value of the
attribute returned. To set a user
role, the value of the attribute
must already be configured on
the W-IAP.
matches-regular-expression —
The rule is applied only if the
attribute value matches the
regular expression pattern
specified in Operand. This
wlan ssid-profile | 557
Command/Parameter
Description
Range
Default
—
Disabled
operator is available only if the
mac-address-and-dhcpoptions attribute is selected in
the Attribute drop-down.
termination
Configures the EAP portion of
802.1X authentication on the WIAP, instead of the RADIUS server.
When enabled, this command
reduces network traffic to the
external RADIUS server by
terminating the authorization
protocol on the W-IAP. By default,
for 802.1X authorization, the client
conducts an EAP exchange with
the RADIUS server, and the W-IAP
acts as a relay for this exchange.
The W-IAP by itself acts as an
authentication server and
terminates the outer layers of the
EAP protocol, only relaying the
innermost layer to the external
RADIUS server.
type {employee|voice|guest}
Configures the type of network
such as employee, voice, guest
network.
—
—
vlan <vlan>
Allows the administrators to assign
a VLAN to the SSID users.
1...4095
—
wep-key <wep-key>
Static WEP key associated with the
key index. The WEP key values
can be 10 or 26 hexadecimal
characters in length.
—
—
wispr
Enables WISPr authentication for
the SSID profile.
—
—
wmm-background-dscp <dscp>
Allows you to specify the DSCP
mapping value for the background
traffic.
0—63
—
wmm-background-share <share>
Allocates bandwidth for
background traffic such as file
downloads or print jobs.
—
—
wmm-best-effort-dscp <dscp>
Allows you to specify the DSCP
mapping value for the best effort
traffic.
0—63
—
wmm-best-effort-share <share>
Allocates bandwidth or best effort
traffic such as traffic from legacy
devices or traffic from applications
or devices that do not support QoS.
—
—
558 | wlan ssid-profile
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Command/Parameter
Description
Range
Default
wmm-video-dscp <dscp>
Allows you to specify the DSCP
mapping value for the video traffic.
0—63
—
wmm-video-share <share>
Allocates bandwidth for video
traffic generated from video
streaming.
—
—
wmm-voice-dscp <dscp>
Allows you to specify the DSCP
mapping value for the voice traffic.
0—63
—
wmm-voice-share <share>
Allocates bandwidth for voice
traffic generated from the incoming
and outgoing voice
communication.
—
—
work-without-uplink
Allows the SSID to be used without
an uplink connection
—
—
wpa-passphrase <passphrase>
Defines a WPA passphrase with
which you can generate a preshared key (PSK).
—
—
zone <zone>
Allows you to specify a zone for
SSID. If an SSID belongs to a
zone, it is not broadcast on any AP
which does not belong to the zone.
Usage Guidelines
Use this command to configure a WLAN SSID profile to set up an employee, voice, or guest network.
Example
The following example configures an employee WLAN SSID profile:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# wlan ssid-profile
AP)(SSID Profile "employee1")#
AP)(SSID Profile "employee1")#
AP)(SSID Profile "employee1")#
AP)(SSID Profile "employee1")#
AP)(SSID Profile "employee1")#
AP)(SSID Profile "employee1")#
AP)(SSID Profile "employee1")#
AP)(SSID Profile "employee1")#
AP)(SSID Profile "employee1")#
AP)(SSID Profile "employee1")#
AP)(SSID Profile "employee1")#
AP)(SSID Profile "employee1")#
AP)(SSID Profile "employee1")#
AP)(SSID Profile "employee1")#
AP)(SSID Profile "employee1")#
AP)(SSID Profile "employee1")#
AP)(SSID Profile "employee1")#
AP)(SSID Profile "employee1")#
AP)(SSID Profile "employee1")#
AP)(SSID Profile "employee1")#
AP)(SSID Profile "employee1")#
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
employee1
type employee
essid employee1
enable
vlan 1
wpa-passphrase user@123
opmode wpa2-psk-aes
max-authentication-failures 0
mac-authentication
l2-auth-failthrough
termination
blacklist
mac-authentication
auth-server InternalServer
rf-band all
dtim-period 1
inactivity-timeout 1000
broadcast-filter none
dmo-channel-utilization-threshold 90
local-probe-req-thresh 0
max-clients-threshold 64
set-role Group-Name contains wireless employee
wlan ssid-profile | 559
(Instant AP)(SSID Profile "employee1")#
expression ..link 200
(Instant AP)(SSID Profile "employee1")#
(Instant AP)(SSID Profile "employee1")#
(Instant AP)(SSID Profile "employee1")#
(Instant AP)(SSID Profile "employee1")#
(Instant AP)(SSID Profile "employee1")#
(Instant AP)(SSID Profile "employee1")#
(Instant AP)# commit apply
set-vlan mac-address-and-dhcp-options matches-regularno wmm-background-dscp
wmm-best-effort-dscp 21
no wmm-video-dscp
wmm-voice-dscp 46,44,42,41
zone Zone1
end
The following example configures a guest WLAN SSID profile:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# wlan ssid-profile guestNetwork
AP)(SSID Profile "guestNetwork")# type guest
AP)(SSID Profile "guestNetwork")# essid guestNetwork
AP)(SSID Profile "guestNetwork")# enable
AP)(SSID Profile "guestNetwork")# opmode opensystem
AP)(SSID Profile "guestNetwork")# rf-band all
AP)(SSID Profile "guestNetwork")# dtim-period 1
AP)(SSID Profile "guestNetwork")# g-min-tx-rate 1
AP)(SSID Profile "guestNetwork")# g-max-tx-rate 54
AP)(SSID Profile "guestNetwork")# a-min-tx-rate 6
AP)(SSID Profile "guestNetwork")# a-max-tx-rate 54
AP)(SSID Profile "guestNetwork")# inactivity-timeout 1000
AP)(SSID Profile "guestNetwork")# vlan 1
AP)(SSID Profile "guestNetwork")# dmo-channel-utilization-threshold 90
AP)(SSID Profile "guestNetwork")# max-clients-threshold 64
AP)(SSID Profile "guestNetwork")# local-probe-req-thresh 0
AP)(SSID Profile "guestNetwork")# blacklist
AP)(SSID Profile "guestNetwork")# max-authentication-failures 3
AP)(SSID Profile "guestNetwork")# radius-interim-accounting-interval 10
AP)(SSID Profile "guestNetwork")# radius-reauth-interval 30
AP)(SSID Profile "guestNetwork")# captive-portal external
AP)(SSID Profile "guestNetwork")# mac-authentication
AP)(SSID Profile "guestNetwork")# auth-server server1
AP)(SSID Profile "guestNetwork")# set-role-by-ssid
AP)(SSID Profile "guestNetwork")# set-role-pre-auth test1
AP)(SSID Profile "guestNetwork")# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.4.0.24.1
This command is modified.
Dell Networking W-Series Instant 6.2.1.03.4
This command is modified.
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and WLAN SSID profile configuration submode.
560 | wlan ssid-profile
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
wlan sta-profile
wlan sta-profile
essid <ESSID>
cipher-suite <cipher-suite-string>
wpa-passphrase <WPA-key>
uplink-band <band>
no…
Description
This command enables Wi-Fi uplink on a W-IAP.
Syntax
Command/Parameter
Description
Range
Default
wlan sta-profile
Configures a Wi-Fi uplink profile for
a W-IAP.
—
—
essid<ESSID>
Defines a unique name for the
network on which the Wi-Fi uplink
will be enabled.
—
—
cipher-suite {clear| wpa-tkippsk| wpa2-ccmp-psk}
Configures encryption settings.
You can specify the following types
of encryption:
—
—
—
—
l
l
l
wpa-passphrase <WPA-key>
clear —To clear a cipher suite
wpa-tkip-psk —To use WPA with
TKIP encryption along with Preshared key (PSK).
wpa2-ccmp-psk — To use WPA2
with Counter Cipher Mode with
Block Chaining Message
Authentication Code Protocol
(CCMP), an AES-based
encryption mode with strong
security.
Defines a WPA passphrase with
which a pre-shared key (PSK) can
be generated.
The passphrase must be between
8 and 64 characters.
uplink-band <band>
Configures the band for uplink
connection. The valid options are
dot11a and dot11g.
—
—
no…
Removes the configuration
—
—
Usage Guidelines
Use this command to configure Wi-Fi uplink for a client station connected to a W-IAP.
Example
The following commands configure the Wi-Fi uplink profile:
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
wlan sta-profile | 561
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config) # wlan sta-profile
AP)(sta uplink)# uplink-band dot11a
AP)(sta uplink)# uplink-band dot11a
AP)(sta uplink)# cipher-suite wpa-tkip-psk
AP)(sta uplink)# wpa-passphrase user@123
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and Wi-Fi uplink (sta) sub-mode.
562 | wlan sta-profile
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
wlan tacacs-server
wlan tacacs-server <profile-name>
ip <IP-address>
port <port>
key <key>
timeout <seconds>
retry-count <number>
deadtime <minutes>
no...
Description
This command is used to configure a TACACS server for management users.
Syntax
Command/Parameter
Description
Default
wlan tacacs-server
Configures the TACACS server profile.
-
ip <IP-address>
Configures the IP address of the TACACS
server.
-
port <port>
Configures the TCP port for the server
key
Configures a shared secret key to authenticate
communication between the TACACS+ client
and server.
timeout <seconds>
Configures a timeout value for TACACS+
requests from the management users
retry-count <number>
Configures the maximum number of
authentication requests that are sent to the
server
3
no…
Removes the specified configuration
parameter.
—
49
-
20
Usage Guidelines
Use this command to configure a TACACS server as an external authentication server. This configuration applies
only for management users in Instant and not for the other SSID or wired profiles.
Example
The following example configures the TACACS protocols:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# wlan tacacs-server Server1
AP)(TACACS Server < Server1>) # ip <10.17.121.54>
AP)(TACACS Server <Server1>) # port <49>
AP)(TACACS Server <Server1>) # key <pass123>
AP)(TACACS Server <Server1>) # timeout <30>
AP)(TACACS Server <Server1>) # retry-count <4>
AP)(TACACS Server <Server1>) # deadtime <30>
AP TACACS Server <Server1>) # end
AP)# commit apply
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
wlan tacacs-server | 563
Command History
Version
Description
Dell Networking W-Series Instant 6.4.0.2-4.1
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and TACACS server profile sub-mode.
564 | wlan tacacs-server
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
wlan walled-garden
wlan walled-garden
white-list <domain>
black-list <domain>
no…
Description
This command configures a walled garden to control user access to the Web content and services. The walled
garden access is required when an external captive portal is used.
Syntax
Command/Parameter
Description
wlan walled-garden
Creates a Walled Garden profile for the W-IAP.
white-list <domain>
Configures a whitelist of URLs to allow the
authenticated users to access to a specific
domain.
You can specify the URLs which the users can
access. To allow access to various sites in the
same domain, you can specify a POSIX regular
expression (regex(7)). For example, yahoo.com/*
to provide access to various domains such as
news.yahoo.com, travel.yahoo.com and
finance.yahoo.com. Similarly, the
www.apple.com/library/test is only allow a subset
of www.apple.com site corresponding to path
/library/test/*.
black-list <domain>
Configures a blacklist to prevent the users from
accessing the websites in a specific domain.
Range
Default
—
—
URLs,
URLs with
POSIX
regular
expression
(regex(7))
—
URLs
—
You can specify the URLs for which the user
access is denied. When a URL specified in
blacklist is accessed by an unauthenticated user,
W-IAP sends an HTTP 403 response to the client
with a simple error message.
no…
Removes the configuration.
—
—
Usage Guidelines
Use this command to configure a walled garden profile. A walled garden access is required when an external captive
portal is used. For example, a hotel environment where the unauthenticated users are allowed to navigate to a
designated login page (for example, a hotel website) and all its contents.
The users who do not sign up for the Internet service can view the “allowed” websites (typically hotel property
websites). The website names must be DNS-based and support the option to define wildcards. This works for client
devices with or without HTTP proxy settings.
When a user attempts to navigate to other websites not in the whitelist of the walled garden profile, the user is
redirected to the login page. Similarly, a blacklisted walled garden profile blocks the users from accessing some
websites.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
wlan walled-garden | 565
Example
The following example configures a walled garden profile:
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# wlan walled-garden
AP)(Walled Garden)# white-list <domain>
AP)(Walled Garden)# black-list <domain>
AP)(Walled Garden)# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
566 | wlan walled-garden
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
wlan wispr-profile
wlan wispr-profile
wispr-location-id-ac <ac>
wispr-location-id-cc <cc>
wispr-location-id-isocc <issoc>
wispr-location-id-network <network>
wispr-location-name-location <location-name>
wispr-location-name-operator-name <operator-name>
no...
Description
This command configures a Wireless Internet Service Provider roaming (WISPr) authentication profile for a W-IAP.
WISPr authentication allows a smart client to authenticate on the network when they roam between wireless Internet
service providers, even if the wireless hotspot uses an Internet Service Provider (ISP) with whom the client may not
have an account.
Syntax
Command/Parameter
Description
wlan wispr-profile
Creates a WISPr authentication profile
wispr-location-id-ac <ac>
Configures an E.164 Area Code for the WISPr Location ID.
wispr-location-id-cc <cc>
Configures an E.164 Country Code for the WISPr Location ID.
wispr-location-id-isocc <issoc>
Configures an ISO Country Code for the WISPr Location ID.
wispr-location-id-network
<network>
Configures an SSID associated with the WISPr Location ID.
wispr-location-name-location
<location-name>
Associates the Hotspot location to the WISPr profile.
wispr-location-name-operatorname <operator-name>
Associates the hotspot operator profile to the WISPr authentication
profile.
no...
Removes the configuration
Usage Guidelines
Use this command to configure a WISPr authentication profile for the captive portal users. Instant supports the
following smart clients:
l
iPass
l
Boingo
These smart clients enable client authentication and roaming between hotspots by embedding iPass Generic
Interface Specification (GIS) redirect, authentication, and logoff messages within HTML messages that are sent to
the W-IAP.
The WISPr RADIUS attributes and configuration parameters are specific to the RADIUS server used by your ISP for
the WISPr authentication. Contact your ISP to determine the parameter values for WISPr profile configuration. You
can find a list of ISO and ITU country and area codes at the ISO and ITU websites (iso.org and itu.int).
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
wlan wispr-profile | 567
Example
The following commands configure a WISPr authentication profile:
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# wlan wispr-profile
AP)(WISPr)# wispr-location-id-ac 408
AP)(WISPr)# wispr-location-id-cc 1
AP)(WISPr)# wispr-location-id-isocc US
AP)(WISPr)# wispr-location-id-network wispr
AP)(WISPr)# wispr-location-name-location airport
AP)(WISPr)# wispr-location-name-operator-name KNP
AP)(WISPr)# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant 6.2.1.03.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode and WISPr profile sub-mode.
568 | wlan wispr-profile
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
write
write {erase <all> <reboot>|memory}
Description
This command saves the running configuration to memory or displays the running configuration on the screen. This
command can also be used to erase the running configuration and return to factory default setting
Syntax
Parameter
Description
erase <all> <reboot>
Erases the running system configuration file. Rebooting the W-IAP resets it to
the factory default configuration. If you specify all, the configuration and all data
in the W-IAP databases are erased.
memory
Saves the current system configuration to memory. Any configuration changes
made during this session will be made permanent.
Usage Guidelines
Configuration changes made using the CLI affect only the current session. You must save your changes for them to
be retained across system reboots. Changes are lost if the system reboots before saving the changes.
The following command assumes you have already saved your configuration. Reboot the W-IAP:
The W-IAP returns the following messages:
Do you really want to reset the system(y/n): y
System will now restart!
...
Restarting system.
Example
The following command saves your changes so they are retained after a reboot:
write memory
Command History
Version
Description
Dell Networking W-Series Instant
6.2.1.0-3.3
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Privileged EXEC mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
write | 569
xml-api-server
xml-api-server
ip <ip-address>
key <shared-key>
no...
Description
This command integrates an XML API interface to the W-IAP.
Syntax
Command/Parameter
Description
xml-api-server
Displays the sub-mode for configuring the XML API interface parameters.
ip <ip-address>
Configures the IP address of the XML API server.
key <shared-key>
Configures the key required for accessing the XML API interface.
no…
Removes the configured parameter.
Usage Guidelines
Use this command to integrate a W-IAP with an external XML API interface.
Example
The following command configures the XML API Server details on a W-IAP:
(Instant
(Instant
(Instant
(Instant
(Instant
AP)(config)# xml-api-server
AP)(xml-api-server)# ip 12.0.132.61
AP)(xml-api-server)# key123
AP)(xml-api-server)# end
AP)# commit apply
Command History
Version
Description
Dell Networking W-Series Instant
6.4.0.2-4.1
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
570 | xml-api-server
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
zonename
zonename <name>
no…
Description
This command configures a zone name for the W-IAP. You can configure zone settings on a W-IAP and the SSID
profile, to assign an SSID to a specific W-IAP.
Syntax
Parameter
Description
zonename <name>
Configures zone on a W-IAP.
no…
Removes the configuration.
Usage Guidelines
Use this command to configure an AP zone. To assign an SSID to a specific W-IAP, the AP zone name must be
configured on the WLAN SSID profile.
The following constraints apply to the AP zone configuration:
l
A W-IAP can belong to only one zone and only one zone can be configured on an SSID.
l
If an SSID belongs to a zone, all W-IAPs in this zone can broadcast this SSID. If no W-IAP belongs to the zone
configured on the SSID, the SSID is not broadcast.
l
If an SSID does not belong to any zone, all W-IAPs can broadcast this SSID.
Example
The following example configures a zone name on a W-IAP:
(Instant AP)# zonename zoneA
Command History
Version
Description
Dell Networking W-Series Instant 6.4.0.24.1
This command is introduced.
Command Information
W-IAP Platform
Command Mode
All platforms
Configuration mode
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
zonename | 571
Terminology
Acronyms and Abbreviations
The following table lists the abbreviations used in this document.
Table 11: List of abbreviations
Abbreviation
Expansion
ARM
Adaptive Radio Management
ARP
Address Resolution Protocol
BSS
Basic Server Set
BSSID
Basic Server Set Identifier
CA
Certification Authority
CLI
Command Line Interface
DHCP
Dynamic Host Configuration Protocol
DMZ
Demilitarized Zone
DNS
Domain Name System
EAP-TLS
Extensible Authentication Protocol- Transport Layer Security
EAP-TTLS
Extensible Authentication Protocol-Tunneled Transport
Layer Security
W-IAP
Instant Access Point
IDS
Intrusion Detection System
IEEE
Institute of Electrical and Electronics Engineers
ISP
Internet Service Provider
LEAP
Lightweight Extensible Authentication Protocol
MX
Mail Exchanger
MAC
Media Access Control
NAS
Network Access Server
NAT
Network Address Translation
NS
Name Server
NTP
Network Time Protocol
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Terminology | 572
Table 11: List of abbreviations
Abbreviation
Expansion
PEAP
Protected Extensible Authentication Protocol
PEM
Privacy Enhanced Mail
PoE
Power over Ethernet
RADIUS
Remote Authentication Dial In User Service
VC
Virtual Controller
VSA
Vendor-Specific Attributes
WLAN
Wireless Local Area Network
Glossary
The following table lists the terms and their definitions used in this document.
Table 12: List of Terms
Term
Definition
802.11
An evolving family of specifications for wireless LANs developed by a
working group of the Institute of Electrical and Electronics Engineers
(IEEE). 802.11 standards use the Ethernet protocol and CSMA/CA (carrier
sense multiple access with collision avoidance) for path sharing.
802.11a
Provides specifications for wireless systems. Networks using 802.11a
operate at radio frequencies in the 5GHz band. The specification uses a
modulation scheme known as orthogonal frequency-division multiplexing
(OFDM) that is especially well suited to use in office settings. The
maximum data transfer rate is 54 Mbps.
802.11b
WLAN standard often called Wi-Fi; backward compatible with 802.11.
Instead of the phase-shift keying (PSK) modulation method historically
used in 802.11 standards, 802.11b uses complementary code keying
(CCK), which allows higher data speeds and is less susceptible to
multipath-propagation interference. 802.11b operates in the 2.4 GHz band
and the maximum data transfer rate is 11 Mbps.
802.11g
Offers transmission over relatively short distances at up to 54 Mbps,
compared with the 11 Mbps theoretical maximum of 802.11b. 802.11g
operates in the 2.4 GHz band and employs orthogonal frequency division
multiplexing (OFDM), the modulation scheme used in 802.11a, to obtain
higher data speed. Computers or terminals set up for 802.11g can fall
back to speeds of 11 Mbps, so that 802.11b and 802.11g devices can be
compatible within a single network.
802.11n
Wireless networking standard to improve network throughput over the two
previous standards 802.11a and 802.11g with a significant increase in the
maximum raw data rate from 54 Mbps to 600 Mbps with the use of four
spatial streams at a channel width of 40 MHz. 802.11n operates in the 2.4
and 5.0 bands.
573 | Terminology
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Table 12: List of Terms
Term
Definition
AP
An access point (AP) connects users to other users within the network and
also can serve as the point of interconnection between the WLAN and a
fixed wire network. The number of access points a WLAN needs is
determined by the number of users and the size of the network.
access point mapping
The act of locating and possibly exploiting connections to WLANs while
driving around a city or elsewhere. To do war driving, you need a vehicle,
a computer (which can be a laptop), a wireless Ethernet card set to work in
promiscuous mode, and some kind of an antenna which can be mounted
on top of or positioned inside the car. Because a WLAN may have a range
that extends beyond an office building, an outside user may be able to
intrude into the network, obtain a free Internet connection, and possibly
gain access to company records and other resources.
ad-hoc network
A LAN or other small network, especially one with wireless or temporary
plug-in connections, in which some of the network devices are part of the
network only for the duration of a communications session or, in the case
of mobile or portable devices, while in some close proximity to the rest of
the network.
band
A specified range of frequencies of electromagnetic radiation.
DHCP
The Dynamic Host Configuration Protocol (DHCP) is an auto-configuration
protocol used on IP networks. Computers or any network peripherals that
are connected to IP networks must be configured, before they can
communicate with other computers on the network. DHCP allows a
computer to be configured automatically, eliminating the need for a
network administrator. DHCP also provides a central database to
keep track of computers connected to the network. This database helps in
preventing any two computers from being configured with the same IP
address.
DNS Server
A Domain Name System (DNS) server functions as a phonebook for the
Internet and Internet users. It converts human readable computer
hostnames into IP addresses and vice-versa.
A DNS server stores several records for a domain name such as an
address 'A' record, name server (NS), and mail exchanger (MX) records.
The Address 'A' record is the most important record that is stored in a DNS
server, because it provides the required IP address for a network
peripheral or element.
DST
Daylight saving time (DST), also known as summer time, is the practice of
advancing clocks, so that evenings have more daylight and mornings
have less. Typically clocks are adjusted forward one hour near the start of
spring and are adjusted backward in autumn.
EAP
Extensible authentication protocol (EAP) refers to the authentication
protocol in wireless networks that expands on methods used by the pointto-point protocol (PPP), a protocol often used when connecting a
computer to the Internet. EAP can support multiple authentication
mechanisms, such as token cards, smart cards, certificates, one-time
passwords, and public key encryption authentication.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Terminology | 574
Table 12: List of Terms
Term
Definition
fixed wireless
Wireless devices or systems in fixed locations such as homes and offices.
Fixed wireless devices usually derive their electrical power from the utility
mains, unlike mobile wireless or portable wireless which tend to be
battery-powered. Although mobile and portable systems can be used in
fixed locations, efficiency and bandwidth are compromised compared with
fixed systems.
frequency allocation
Use of radio frequency spectrum regulated by governments.
frequency spectrum
Part of the electromagnetic spectrum.
hotspot
A WLAN node that provides Internet connection and virtual private
network (VPN) access from a given location. A business traveler, for
example, with a laptop equipped for Wi-Fi can look up a local hot spot,
contact it, and get connected through its network to reach the Internet and
their own company remotely with a secure connection. Increasingly, public
places, such as airports, hotels, and coffee shops are providing free
wireless access for customers.
IEEE 802.11 standards
The IEEE 802.11 is a set of standards that are categorized based on the
radio wave frequency and the data transfer rate.
POE
Power over Ethernet (PoE) is a method of delivering power on the same
physical Ethernet wire used for data communication. Power for devices is
provided in one of the following two ways:
l Endspan— The switch that an AP is connected for power supply.
l Midspan— A device can sit between the switch and APs
The choice of endspan or midspan depends on the capabilities of the
switch to which the W-IAP is connected. Typically if a switch is in place
and does not support PoE, midspan power injectors are used.
PPPoE
Point-to-Point Protocol over Ethernet (PPPoE) is a method of connecting
to the Internet typically used with DSL services where the client connects
to the DSL modem.
QoS
Quality of Service (QoS) refers to the capability of a network to provide
better service to a specific network traffic over various technologies.
RF
Radio Frequency (RF) refers to the portion of electromagnetic spectrum in
which electromagnetic waves are generated by feeding alternating current
to an antenna.
TACACS
Family of protocols that handle remote authentication and related services
for network access control through a centralized server.
TACACS+
Derived from TACACS but an entirely new and separate protocol to
handle AAA services. TACACS+ uses TCP and is not compatible with
TACACS. Because it encrypts password, username, authorization, and
accounting, it is less vulnerable than RADIUS.
VPN
A Virtual Private Network (VPN) network that uses a public
telecommunication infrastructure, such as the Internet, to provide remote
offices or individual users with secure access to their organization's
network. A VPN ensures privacy through security procedures and
tunneling protocols such as the Layer Two Tunneling Protocol ( L2TP ).
Data is encrypted at the sending end and decrypted at the receiving end.
575 | Terminology
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Table 12: List of Terms
Term
Definition
W-CDMA
Officially known as IMT-2000 direct spread; ITU standard derived from
Code-Division Multiple Access (CDMA). Wideband code-division multiple
access (W-CDMA) is a third-generation (3G) mobile wireless technology
that promises much higher data speeds to mobile and portable wireless
devices than commonly offered in today's market.
Wi-Fi
A term for certain types of WLANs. Wi-Fi can apply to products that use
any 802.11 standard. Wi-Fi has gained acceptance in many businesses,
agencies, schools, and homes as an alternative to a wired LAN. Many
airports, hotels, and fast-food facilities offer public access to Wi-Fi
networks.
WEP
Wired equivalent privacy (WEP) is a security protocol specified in 802.11b,
designed to provide a WLAN with a level of security and privacy
comparable to what is usually expected of a wired LAN. Data encryption
protects the vulnerable wireless link between clients and access points;
once this measure has been taken, other typical LAN security
mechanisms such as password protection, end-to-end encryption, virtual
private networks (VPNs), and authentication can be put in place to ensure
privacy.
wireless
Describes telecommunications in which electromagnetic waves (rather
than some form of wire) carry the signal over part or all of the
communication path.
wireless network
In a Wireless LAN (WLAN), laptops, desktops, PDAs, and other computer
peripherals are connected to each other without any network cables.
These network elements or clients use radio signals to communicate with
each other. Wireless networks are set up based on the IEEE 802.11
standards.
WISP
Wireless ISP (WISP) refers to an internet service provider (ISP) that allows
subscribers to connect to a server at designated hot spots (access points)
using a wireless connection such as Wi-Fi. This type of ISP offers
broadband service and allows subscriber computers, called stations, to
access the Internet and the Web from anywhere within the zone of
coverage provided by the server antenna, usually a region with a radius of
several kilometers.
wireless service provider
A company that offers transmission services to users of wireless devices
through radio frequency (RF) signals rather than through end-to-end wire
communication.
WLAN
Wireless local area network (WLAN) is a local area network (LAN) that the
users access through a wireless connection.
Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide
Terminology | 576