Download MTP U R Series • Setup Guide

NT: plete
RTAfor the coomns, and
O
P
m
o
M
I tron.c instructi ng the
.ex
on
ecti .
www stallati
e
conn
Go to uide, in s before er sourc
g
n
ow
p
e
user cificatio
th
to
e
t
p
s
uc
prod
MTP U R Series • Setup Guide
DELAY
SIGNAL
VID
Y/C
YUV SELECT
RGB
AUDIO
RS-232
RGB
R
G
B
PEAKING
LEVEL
ADJUST
This card provides quick start instructions for an experienced installer to set up
and operate any of the MTP U R Series products.
MTP U R RSA SEQ
JMP1
Pre-installation — Jumper Settings
JMP2
JMP3
Default settings
(viewed from rear)
The MTP U R has three jumpers located on the main board. JMP1 is RS-232 directional communication,
and JMP2 and JMP3 are for vertical and horizontal sync (respectively). By default JMP1 is bidirectional;
JMP2 and JMP3 are negative sync.
Installation
RJ-45
Connector
Step 1 — Mounting
Pins:
12345678
Turn off or disconnect all equipment power sources and mount the MTP U R as required.
Step 2 — Connect Input
Connect the RJ-45 cable from an MTP transmitter to the Input port on the MTP U R. Terminate the
cable as shown on the right, using the same standard (A or B) at both ends.
POWER
12V
0.5A MAX
T568B
Wire color
1
White-green
White-orange
2
Green
Orange
3
White-orange White-green
4
Blue
5
White-blue
White-blue
6
Orange
Green
Blue
7
White-brown White-brown
8
Brown
Brown
Insert Twisted
Pair Wires
CAT 7 INPUT
NOTE:
T568A
Wire color
Pin
If the input is labeled “CAT 7 Input”, only a CAT 7 cable should be used (that is, MTP C7 U R RSA SEQ model).
Step 3 — Connect Outputs
OUTPUTS
Attach the applicable output cables (video, audio, and RS-232), depending on the MTP U R model used.
R-Y
Y
Composite video output connector — Connect to the single female BNC connector (VID) .
•
S-video output connector — Connect to the 4-pin mini DIN connector (Y/C).
•
Component video (MTP U R RSA SEQ model only) — Connect to the three female BNC
connectors (Y, R-Y, and B-Y).
•
High resolution video output connector — Connect to the 15-pin HD connector (RGB).
Connected RS-232
Device Pins
•
RS-232 connector — Connect a serial communications port to the upper 3.5 mm,
5-pole captive screw connector for bidirectional RS-232 communication (as shown).
Receive
Transmit
Ground
•
Audio connector (MTP U R RSA SEQ and MTP U R A models only) — Connect a suitable
audio device to the lower 5-pole captive screw connector for mono audio output (as shown).
NO GROUND.
Unbalanced Output
Mono output 1+
Mono output 1Sleeve(s)
Mono output 2+
Mono output 2-
Tx Rx
SPACE
MONO AUDIO
1
2
Y/C
RGB
MONO AUDIO
1
2
Do not tin the wires!
Sleeve(s)
Mono output 2
MONO AUDIO
1
2
NO GROUND.
B-Y
VID
•
Mono output 1
RS-232
MTP/HDMI U R
Pins
Tx
Rx
Gnd
Spare
Spare
audio device
Balanced Output
Step 4 — Power
Plug the included external 12 VDC power supply into the 2-pole captive screw connector. Wire the
connector (see image a on the right).
a
POWER
12V
xA MAX
Smooth
Ridges
A
A
3/16"
(5 mm)
Max.
Grounding guidelines
Extron MTP U R products can be adversely affected by electrostatic discharge (ESD) if they are not
grounded correctly.
To prevent malfunctions or product damage, an experienced installer can correctly ground an
Extron MTP U R product in either of two ways:
•
Ground the power input port — Insert one end of the grounding wire to the negative or ground pin on
the power input connector (see image a on the right). Tie the other end of the wire to an earth ground.
•
Ground the chassis — Use a connector hex nut as shown in image b the right. Tie the other end of
the wire to an earth ground.
If you have any questions about how to ground a product in a specific application, contact an Extron technical
support specialist.
Rear
Panel
SECTION A–A
Power Supply
Output Cord
b
Tie
Wrap
Ridges
Earth
Ground
MTP U R Series • Setup Guide
Step 5 — Input Signal Detection
Check the displayed output is correct. The MTP U R detects the input signal format, indicated by the front panel LEDs (VID, Y/C,
YUV, RGB), and differentiates between RS-232 and audio signals. The output is then made on the appropriate connector and
all other outputs are muted.
Step 6 — Peaking and Level
Image sharpness is adjusted with the Peaking Control. Increased peaking compensates for mid- and
high-frequency detail loss. Minimum setting (full counterclockwise) is zero peaking.
RGB
PEAKING
LEVEL
Image brightness is adjusted using the Level Control. View the image and adjust the control for the best image quality.
MTP U R RS SEQ
Step 7 — Skew Compensation
Pair skew can be measured with test equipment or by viewing a crosshatch test pattern. The SEQ receivers have built-in
skew compensation capabilities. Adjust the equalization as follows:
SIGNAL
A. Zero the skew delay for red, green, and blue by using a Tweeker or small screwdriver to press and hold the SelectVID
Y/C
button for 3 seconds. When the Red, Green, and Blue LED’s all go out, release the Select button.
YUV
B. Use UTP cable test equipment or examine the displayed image to determine which video signal (red, green, or
blue) is shifted furthest to the right.
DELAY
RGB
R
SELECT
RGB
G
B
LEVEL
MTP U R RS S
C. Adjust the furthest left video signal towards the right by using a Tweeker or screwdriver to press and release the
Select button until the LED for the left-shifted color lights.
D. Slowly rotate the Adjust control clockwise until the shifted color is properly aligned.
E. Repeat steps C and D to align the third color if needed.
Extron
MTPX 1616 Plus
UT
MTP Matrix Switcher
Extron
MTP U R RS
S
TP
OU
NO
VID
MT
P
U
R
DIO
AU 2
MO
1
Universal Receiver
RS
Y/C
B
RO
SET
Tx
Tx
Tx
6
Tx
1
2
RJ
3
S
5
Extron
MTP U R A
16
15
14
8
ON
3
UT
12
11
6
10
9
16
3
15
2
CT
SELE
14
1
LOCAL
INPUT
B
RG
Rx
8
13
4
- 45
UT
12
S
TP
OU
11
10
B
RG
3
2
NO
4 2
3 2
2 2
1 2
9
2
1
VID
1
1
S
1
UT
1
DIO
UT
INP
6
S
UT
5
13
7
INP
4
TS
TPU
L OU
CA B
RG
LO
Tx
Rx
7
TP
3
2
1
S
UT
L INP
1
CA
LO RGB
Tx
Rx
Rx
Rx
OU
4
REMOTE
Tx
Rx
Rx
Rx
12VA MA
0.5
RS-232/RS-422
7
- 232
L RS 5
CA
LO
4
3
2
1
Tx
ETHERNET
RE
8
RG
R
WE
PO X
L
ACT LINK
NT
CO
MT
INP
P
U
R
A
MO
1
DIO
AU 2
Universal Receiver
Projector
Y/C
AU
B
RG
R
WE
PO X
12VA MA
0.5
Extron
MTP T SV A
UT
INP
UTR
INP
L
IDE
O
S-V
UT
TP
OU
A
SV
PT
MT
X
12V MA
0.5a
MT
P
T
15
HD
A
K
-PEA
PRE
ON
UT
TP
OU
DIO
Transmitter
AU
OFF
MO
OR
NIT
Flat Panel
Display
R
WE
PO
12V MA
.5A
DING
e
/-R
DVD-RW
Precision
RECOR
Progressiv
Cinema
DVD
X
UT
INP
Extron
MTP T 15HD A
Transmitter
PC
Figure 1. Example of a Typical MTP U R Series Application
Extron Headquarters
+800.633.9876 Inside USA/Canada Only
Extron USA - West
Extron USA - East
+1.714.491.1500+1.919.850.1000
+1.714.491.1517 FAX
+1.919.850.1001 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
Extron Asia
+800.7339.8766
Inside Asia Only
+31.33.453.4040
+31.33.453.4050 FAX
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+4000.EXTRON
+4000.398766
Inside China Only
Extron
Middle East
+971.4.2991800
+971.4.2991880 FAX
+86.21.3760.1568
+86.21.3760.1566
FAX
© 2013 Extron Electronics All rights reserved. www.extron.com
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
PEAKIN
ADJUST
Extron India
1800.3070.3777
Inside India Only
+91-80-3055.3777
+91 80 3055 3737
FAX
68-1367-50
Rev. B
01 13