Download Extron electronic 1500RL User's Manual

e
:
ANT omplet
ORoTm for thuecctions, aned
IMP
.c
r
h
t
ins
ing t
xtron
w.e tallation onnect .
e
c
o ww
s
Go t uide, in s before er sourc
g
w
n
user cificatio o the po
t
e
t
p
s
uc
prod
MTP 1500RL 15HD RS SEQ • Setup Guide
This guide provides basic instructions for an experienced installer to set up and operate the Extron MTP 1500RL
15HD RS SEQ twisted pair receiver.
For full details, see the MTP 1500RL 15HD RS SEQ User Guide, available online at www.extron.com.
RED
BLUE
DELAY
ADJUST
PEAKING
RGB
BUFFERED OUTPUT
INPUT
POWER
12V
1.0A MAX
LEVEL
GREEN
MIN/MAX
MTP 1500RL SERIES
H+
V+
CSYNC
SOG
VIDEO
END
BI-232
SELECT
OUTPUT
RS-232
MTP
MTP
ON
MTP 1500RL 15HD RS SEQ
Tx Rx
Installation and Setup
Step 1 — Mounting
Turn off or disconnect all equipment power sources. Mount the MTP 1500RL 15HD RS SEQ receiver as required.
Step 2 — Connect Input
Connect the RJ-45 cable from an MTP transmitter to the Input port on the MTP 1500RL 15HD RS SEQ receiver.
Terminate the cable as shown below right, using the same standard (T568A or T568B) at both ends.
Transmission distance with one device before the MTP 1500RL 15HD RS SEQ
1500 feet (457 m) maximum (video signals)
Input
Source
VGA
cable
TP
cable
MTP Tx
Device
MTP 1500RL
15HD RS Device
VGA
cable
Display
Pin
T568A Wire
Color
T568B Wire
Color
1
White-green
White-orange
2
Green
Orange
3
White-orange
White-green
4
Blue
Blue
5
White-blue
White-blue
6
Orange
Green
7
White-brown
White-brown
8
Brown
Brown
RJ-45 Connector
Pins:
12345678
1000 feet (305 m) maximum
(RS-232 data signals)
Transmission distance with more than one device before the MTP 1500RL 15HD RS SEQ
1500 feet (457 m) maximum (video signals)
Input
Source
VGA
cable
MTP Tx
Device
TP
cable
MTP RL Rx
Device
TP
cable
MTP 1500RL
15HD RS Device
VGA
cable
Display
Insert Twisted
Pair Wires
1000 feet (305 m) maximum
(RS-232 data signals)
NOTE: The transmitter and receiver are designed for and perform best with Extron Enhanced Skew-Free™ AV cable terminated in accordance
with the TIA/EIA T568A standard. CAT 5 cables are acceptable but less preferable. Using preterminated and tested cables is also
recommended. Cables terminated on site should be tested before use to ensure that they comply with Category 5 specifications.
Step 3 — Connect Outputs
A. High resolution video output — Connect a suitable display device to the 15-pin HD
connector (RGB).
B. RS-232 connector — Connect an RS-232 compatible MTP transmitter to the 3-pole
captive screw connector (wired as shown at right) for bi-directional or uni-directional
communication up to 1,000 feet, (305 meters) maximum.
Connected RS-232
Device Pins
MTP Reciever
Pins
Receive
Transmit
Ground
Tx
Rx
Gnd
H+
V+
CSYNC
SOG
VIDEO
END
BI-232
Attach the applicable output cables (video, audio, and buffered output).
C. Buffered output — Connect up to 5 daisy-chained MTP receivers to this RJ-45 connector.
Step 4 — Receiver DIP Switches
•
H sync (H+) and V sync (V+) switches — Set these switches up (On) for positive sync or
down (Off) for negative sync.
•
Composite Sync, SOG, and Video switches — Set these switches as shown in the table
(see right) to output the indicated format.
•
•
End Unit switch — Set this switch up if either of the following is true:
•
The receiver being configured is the only receiver connected to the transmitter.
•
The receiver being configured is the last receiver in a daisy-chained system.
BI-232 switch — Set this up (ON) for bi-directional or down for uni-directional communication.
ON
Output
Format
C Sync SOG Video
RGBHV
RGBS
RGsB
Component*
S-video*
Composite*
* Input video format must match.
MTP 1500RL 15HD RS SEQ • Setup Guide (Continued)
Step 5 — Power
a
Wire the 2-pole captive screw connectors for the included external 12 VDC power supplies (see
image a on the right). Plug them into all units.
POWER
12V
xA MAX
Smooth
A
Ridges
A
Grounding guidelines
3/16"
(5 mm)
Max.
Extron MTP 1500RL 15HD RS SEQ products can be adversely affected by electrostatic discharge (ESD)
if they are not grounded correctly.
To prevent malfunctions or product damage, an experienced installer can correctly ground an Extron
MTP 1500RL 15HD RS SEQ product in either of two ways:
•
•
Rear
Panel
Tie
Wrap
SECTION A–A
Ridges
Power Supply
Output Cord
Earth
Ground
Ground the power input port — Insert one end of the grounding wire to the negative or ground pin
on the power input connector (see image a on the right). Tie the other end of the wire to an earth
ground.
b
Ground the chassis — Use a connector hex nut (see image b on the right). Tie the other end of
the wire to an earth ground.
If you have any questions about how to ground a product in a specific application, contact an Extron technical
support specialist.
Step 6 — Peaking and Level
Adjust the image sharpness using the Peaking control. Increased peaking compensates for mid- and high-frequency
detail loss. The LED lights red when minimum (zero) or maximum peaking is reached.
LEVEL
Adjust the image brightness using the Level control. View the image and adjust either control for the best image quality.
PEAKING
RGB
Step 7 — Skew Compensation
MIN/MAX
Pair skew can be measured with test equipment or by viewing a crosshatch test pattern. The SEQ receivers have
built-in skew compensation capabilities. Adjust the equalization as follows:
A. Set the skew delay to zero for red, green, and blue by using a Tweeker or small screwdriver to press and hold
the Select button for 3 seconds. When the Red, Green, and Blue LEDs all go out, release the Select button.
B. Use UTP cable test equipment or examine the displayed image to determine which video signal — red, green,
or blue — is shifted furthest to the right.
RED
SELECT
GREEN
BLUE
DELAY
ADJUST
C. Adjust the furthest left video signal by using a Tweeker or screwdriver to press and release the Select button until
the LED for the left-shifted color lights.
D. Slowly rotate the Adjust control clockwise until the shifted color is properly aligned.
E. Repeat steps C and D to align the third color if needed.
Extron
MTP 1500RL 15HD RS SEQ
Twisted Pair Receiver
with Loop-Through and Skew EQ
H+
V+
CSYNC
SOG
VIDEO
END
BI-232
Flat Panel
Display
ON
D RS
0RL
2
UT
TP
-23
RS
OU
Tx
Rx
RS-232
SEQ
15H
P 150
MT
RGBHV
UT
TP
D
RE
OU
FFE
BU
INP
UT
P
MT
POW
12V MAX
1.0A
Extron
MTP T 15HD RS
RGBHV
500' (152 m) UTP Cable
(CAT 5/5e/6)
Flat Panel
Display
Twisted Pair
Transmitter
RS-232
MT
P
T
VG
A
RS
LE
H+
V+
CSYNC
SOG
VIDEO
END
BI-232
PC
Extron
MTP 1500RL 15HD RS SEQ
Twisted Pair Receiver
with Loop-Through and Skew EQ
P
MT
ER
500' (152 m) UTP Cable
(CAT 5/5e/6)
ON
LONG
NORM
32
RS-2
Tx
Rx
X
D
RE
OU
OR
NIT
MO
12V MA
.5A
UT
INP
-23
RS
Tx
UT
UT
TP
R
WE
PO
D RS
0RL
2
UT
TP
OU
CAB
Rx
SEQ
RS-232
15H
P 150
MT
RGBHV
TP
OU
FFE
Maximum transmission distances:
Data (RS-232) 1000' (305 m)
Video
15 00' (457 m)
BU
UT
INP
P
MT
P
MT
ER
POW
12V MAX
1.0A
Figure 1. Example of a Typical MTP 1500RL 15HD RS SEQ Application
Extron USA Headquarters +1.800.633.9876 (USA/Canada Only)
Extron USA - West: +1.714.491.1500 FAX: +1.714.491.1517
Extron USA - East: +1.919.850.1000 FAX: +1.919.850.1001
© 2013 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
68-1555-50
Rev. C
01 13