Download Mitsubishi Electric CITY MULTIPMFY-P08NBMU-E Service manual

SPLIT-TYPE, HEAT PUMP AIR CONDITIONERS
April 2009
No. OCH461
TECHNICAL & SERVICE MANUAL
R410A R22
Indoor unit
[Model names]
PKFY-P06NBMU-E
PKFY-P08NBMU-E
[Service Ref.]
PKFY-P06NBMU-E
PKFY-P08NBMU-E
Note:
• This manual describes
only service data of the
indoor units.
• RoHS compliant products
have <G> mark on the
spec name plate.
CONTENTS
1. PART NAMES AND FUNCTIONS .......... 2
2. SPECIFICATION ..................................... 4
3. OUTLINES AND DIMENSIONS .............. 6
4. WIRING DIAGRAM ................................. 7
5. REFRIGERANT SYSTEM DIAGRAM.......... 8
6. MICROPROCESSOR CONTROL ........... 9
7. TROUBLESHOOTING .......................... 14
8. DISASSEMBLY PROCEDURE ............. 21
INDOOR UNIT
Model name
indication
PARTS CATALOG (OCB461)
1
PART NAMES AND FUNCTIONS
Air intake
Indoor unit
Filter
Grille
Vane
Louver
Air outlet
Wireless remote controller
display
CHECK TEST RUN display
CHECK and TEST RUN display indicate that
the unit is being checked or test-run.
Lights up while the signal is transmitted to
the indoor unit when the button is pressed.
display
MODEL SELECT display
SET TEMP. display indicates the set desired
temperature.
Blinks when model is selected.
CLOCK display
display
Displays the current time.
OPERATION MODE display
Operation mode display indicates which
operation mode is in effect.
TIMER display
CHECK TEST RUN
MODEL SELECT
°F
°C
AMPM
Displays when in timer operation or when
setting timer.
“
AMPM
NOT AVAILABLE
display
The vertical direction of air flow is indicated.
ON/OFF
“
TEMP
”“
” display
Displays the order of timer operation.
”“
” display
Displays whether timer is on or off.
display
button
FAN SPEED display indicates which fan
speed has been selected.
FAN
AUTO STOP
VANE
AUTO START
SET TEMPERATURE button sets any desired
room temperature.
ON/OFF button
The unit is turned ON and OFF alternately
each time the button is pressed.
MODE
TIMER CONTROL buttons
CHECK LOUVER
h
FAN SPEED SELECT button
Used to change the fan speed.
MODE SELECT button
TEST RUN
SET
min
RESET
Used to switch the operation mode between
cooling, drying, fan, heating and auto mode.
AUTO STOP (OFF timer): when this switch is
set, the air conditioner will be automatically
stopped at the preset time.
AUTO START (ON timer): when this switch is
set, the air conditioner will be automatically
started at the preset time.
CLOCK
h and min buttons
Buttons used to set the “hour and minute” of
the current time and timer settings.
+ In case the outdoor unit is cool only type,
the heating and auto mode are not
available.
LOUVER button
Changes left/right airflow direction.
CHECK-TEST RUN button
(Not available for this model.)
Only press this button to perform an
inspection check or test operation.
Do not use it for normal operation.
CLOCK button
RESET button
VANE CONTROL button
SET button
Used to change the air flow
2
Wired remote controller
Display Section
For purposes of this explanation,
all parts of the display are shown
as lit. During actual operation, only
the relevant items will be lit.
Day-of-Week
“Sensor” indication
Shows the current day of the week.
Displayed when the remote controller
sensor is used.
Time/Timer Display
Shows the current time, unless the simple or Auto Off
timer is set.
If the simple or Auto Off timer is set, the time to be
switched off is shown.
“Locked” indicator
Indicates that remote controller buttons have been locked.
Identifies the current operation
“Clean The Filter” indicator
Shows the operating mode, etc.
*Multilanguage display is available.
To be displayed on when it is time to
clean the filter.
TIME SUN MON TUE WED THU FRI SAT
TIMER
Hr
ON
AFTER
Indicates that operation from the
remote controller has been prohibited by a master controller.
FUNCTION
FILTER
°F°C
°F°C
“Centrally Controlled” indicator
Timer indicators
AFTER OFF
ERROR CODE
The indicator comes on if the corresponding timer is set.
WEEKLY
SIMPLE
AUTO OFF
ONLY1Hr.
Fan Speed indicator
Shows the selected fan speed.
“Timer is Off” indicator
Indicates that the timer is off.
Up/Down Air Direction indicator
The indicator shows the direction of the outcoming airflow.
Room Temperature display
Shows the room temperature. The room
temperature display range is 46–102°F.
The display blinks if the temperature
is less than 46°F or 102°F or more.
Ventilation indicator
Appears when the unit is running in
Ventilation mode.
“One Hour Only” indicator
Temperature Setting
Shows the target temperature.
Displayed if the airflow is set to
Low or downward during COOL
or DRY mode. (Operation varies
according to model.)
The indicator goes off in one hour,
at which time the airflow direction
also changes.
Louver display
Indicates the action of the swing louver.
Does not appear if the louver is not
running.
(Power On indicator)
Indicates that the power is on.
Operation Section
ON/OFF button
Temperature setting buttons
Down
Fan Speed button
Up
Timer Menu button
(Monitor/Set button)
Filter
button
(<Enter> button)
Mode button (Return button)
TEMP.
ON/OFF
Set Time buttons
Check button (Clear button)
Back
Ahead
Timer On/Off button
(Set Day button)
Test Run button
MENU
BACK
PAR-21MAA
MONITOR/SET
ON/OFF
FILTER
DAY
CLOCK
CHECK TEST
OPERATION
Airflow Up/Down button
CLEAR
Louver button
(
Operation button)
To return operation
number
Opening the
lid
Built-in temperature sensor
Ventilation button
( Operation button)
To go to next operation
number
Note:
● “PLEASE WAIT” message
This message is displayed for approximately 3 minutes when power is supplied to the indoor unit or when the unit is recovering from a power failure.
● “NOT AVAILABLE” message
This message is displayed if an invalid button is pressed (to operate a function that the indoor unit does not have).
If a single remote controller is used to operate multiple indoor units simultaneously that are different types, this message will not be displayed as
far as any of the indoor units is equipped with the function.
3
2
SPECIFICATION
2-1. Specifications
PKFY-P08NBMU-E
PKFY-P06NBMU-E
Service Ref.
1-phase 208/230V 60Hz
Power source
Cooling capacity
(Nominal)
*1
*1
Power input
Current input
Heating capacity
(Nominal )
*2
*2
Power input
Current input
External finish
External dimension H × W × D
Net weight
Heat exchanger
Fan
kW
Btu/h
kW
A
kW
Btu/h
kW
A
2.3
8,000
0.03
0.15
2.6
9,000
0.03
0.15
1.8
6,000
0.03
0.15
2.0
6,700
0.03
0.15
Plastic, MUNSELL (1.0Y 9.2/0.2)
295 × 815 × 225
11-5/8" × 32-1/8" × 8-7/8"
10 (22)
Cross fin (Aluminum fin and copper tube)
mm
in.
kg (lb)
Line flow fan × 1
0
0
1-phase induction motor
Type × Quantity
External
static press.
Pa
mmH2O
Motor type
Motor output
kW
0.008
Direct-driven by motor
Driving mechanism
Airflow rate
m3/min
cfm
Noise level (Low-Mid2-Mid1-High)
dB <A>
(measured in anechoic room)
Insulation material
Air filter
Protection device
Refrigerant control device
Connectable outdoor unit
Diameter of
(R410A) mm (in.)
Liquid
refrigerant pipe
(R22)
Gas
Polyethylene sheet
PP honeycomb
Fuse
LEV
R410A, R22 CITY MULTI
ø6.35 (ø1/4")
ø6.35 (ø1/4")
ø12.7 (ø1/2")
ø12.7 (ø1/2")
Flare
Flare
Flare
Flare
Field drain pipe size
Standard
Document
attachment
Accessory
External heater adapter
Remarks
Installation
Note :
Indoor :
Outdoor :
Pipe length :
Level difference :
*1 Nominal cooling conditions
32 - 33 - 35 -36
32 - 33 - 35 -36
(R410A) mm (in.)
(R22)
mm (in.)
Optional parts
4.9 - 5.2 - 5.6 - 5.9
82 - 87 - 93 - 98
170 - 180 - 200 - 210
4.9 - 5.2 - 5.6 - 5.9
82 - 87 - 93 - 98
170 - 180 - 200 - 210
(Low-Mid2-Mid1-High) L/s
ø6.35 (ø1/4")
ø6.35 (ø1/4")
ø12.7 (ø1/2")
ø12.7 (ø1/2")
Flare
Flare
Flare
Flare
I.D. 16mm (5/8")
Installation Manual, Instruction Book
MA remote controller cable
PAC-SA88HA-E
Details on foundation work, insulation work, electrical wiring, power source switch, and other items shall be referred to
the Installation Manual.
Unit converter
*2 Nominal heating conditions
80°FDB/67°FWB (26.7°CDB/19.4°CWB)
95°FDB (35°CDB)
25 ft. (7.6 m)
0 ft (0 m)
70°FDB(21°CDB)
47°FDB/43°FWB (8.3°CDB/6.1°CWB)
25 ft. (7.6 m)
0 ft (0 m)
* Due to continuing improvement, above specification may be subject to change without notice.
4
kcal/h
Btu/h
cfm
lb
= kW × 860
= kW × 3,412
= m3/min × 35.31
= kg/0.4536
*Above specification data is
subject to rounding variation.
2-2. Electrical parts specifications
Service Ref.
PKFY-P06NBMU-E
Symbol
PKFY-P08NBMU-E
Parts name
Room temperature
thermistor
TH21
Resistance 30°F/15.8k, 50°F/9.6k, 70°F/6.0k, 80°F/4.8k, 90°F/3.9k, 100°F/3.2k
Liquid pipe thermistor
TH22
Resistance 30°F/15.8k, 50°F/9.6k, 70°F/6.0k, 80°F/4.8k, 90°F/3.9k, 100°F/3.2k
Gas pipe thermistor
TH23
Resistance 30°F/15.8k, 50°F/9.6k, 70°F/6.0k, 80°F/4.8k, 90°F/3.9k, 100°F/3.2k
Fuse
(Indoor controller board)
Fan motor
(with thermal fuse)
FUSE
250V 6A
MF
4-Pole Output 8W / PS4N8-KB
Fan motor capacitor
C1
1.2 × 440V
Vane motor
(with limit switch)
MV
MSFBC20 DC12V
Linear expansion valve
LEV
DC12V Stepping motor drive
Port :3.2 (0~2000pulse)
Power supply terminal
block
TB2
(L1, L2, GR) 250V 20A
TB5
(M1, M2, S) 250V 20A
TB15
(1, 2) 250V 10A
Transmission terminal
block
MA remote controller
terminal block
2-3. Sound levels
Sound level at anechoic room : Low-Middle2-Middle1-High
Sound level dB (A)
Service Ref.
32-33-35-36
PKFY-P08NBMU-E
32-33-35-36
3.3 ft.
(1m)
PKFY-P06NBMU-E
Measurement location
3.3 ft.
(1m)
PKFY-P06/08NBMU-E
External static pressure : 0Pa
Power source : 208,230V, 60Hz
OCTAVE BAND PRESSURE LEVEL (dB) 0dB = 20MPa
* Measured in anechoic room.
2-4. NC curve
70.0
High speed
Low speed
65.0
60.0
NC60
55.0
50.0
NC50
45.0
40.0
NC40
35.0
30.0
NC30
25.0
20.0
15.0
10.0
Approximate minimum
audible limit on
continuous noise
63
125
250
NC20
500
1k
2k
4k
OCTAVE BAND CENTER FREQUENCIES(Hz)
5
8k
OUTLINES AND DIMENSIONS
30-13/16(783)
Air intake
Unit : inch (mm)
17/32(14)
3-15/16(100.6)
PKFY-P06NBMU-E
PKFY-P08NBMU-E
32-1/8(815)
25-3/16(640)
4-1/2(115)
Air intake
8-7/8(225)
Air intake
(Direction)
4-3/16(106.7)
3/16(5)
1/8(3)
installaion plate
11-5/8(295)
Power supply
Transmission
2-3/8
(60)
26-31/32(660)(Drain pipe total 29-29/32(760))
Knockout holt for
under piping
Knockout hole of
remote control wiring
45°
5/8(16)
1-31/32(50)
1-31/32(50)
13/32(10)
R1
9/3
2(R
15
)
5)
2(R1
R19/3
R5/1
6(R8
)
R5/16
(R8)
5/8(16)
3/32(2.5)
1-25/32(45)
13/32(10)
1-11/32(34)
3-19/32(91.5)
Knockout hole of
right piping
Min1-31/32(50)
Note 1. Use M10 or W3/8 screw for installation plate.
Note 2. Extension piping side.
Note 3. In case of connecting MA-remote controller, please use
MA-remote controller cable in an accessories to the connector.
Refrigerart
piping
Min3-15/16(100)
Liquid pipe
1/4F(:6.35)
Gas pipe
1/2F(:12.7)
6-5/8(168)
5-5/16(135)
4-29/32(125)
4-11/32(110)
6-1/4(159)
5-1/4(133)
4-13/16(122.5)
3-27/32(97.5)
3-11/32(85)
2-27/32(72.5)
2-3/8(60)
1-7/8(47.5)
7/8(22.5)
3/16×1-15/32(4.5×37) 4 holes
3/16×1-9/16(4.5×40) 4 holes
11-23/32(298)
9-1/4(235)
Knock of hole
6-11/16(170)
6-7/8(175)
8-1/16(205)
13/32(10)
0
13/32(10)
8-1/16(205)
6-7/8(175)
6-11/16(170)
9-1/4(235)
12-29/32(328)
3-17/32(90)
4-1/32(102.5)
4-7/8(124)
1-3/8(35)
13/32(10)
0
1-3/32(27.5)
1-9/16(40)
2-3/32(53)
2-9/16(65)
3-7/16(87)
4-7/16(113)
5-1/32(128)
1-23/32(44)
1-31/32(50)
0
19/32(15)
8-:5/32(:4.3) holes
16-1/32(407.5)
11-23/32(298)
10-1/4(260)
8-27/32(225)
6-3/32(155)
7-3/32(180)
7-15/32(190)
4-23/32(120)
3-11/32(85)
8-27/32(225)
Details of installation plate
7-15/32(190)
6-1/4(159)
6-3/32(155)
4-23/32(120)
10-1/4(260)
11-5/8(295)
12-29/32(328)
Installation plate
16-1/32(407.5)
Installation plate balance point hole
:5/8(:16) I.D
Min3-35/64(90)
1-3/16(30)
0
1-3/16(30)
1-3/4(45)
Min25/32(20)
Piping hole:2-9/16(:65)
12-:1/8(:2.8)holes
4-:11/32(:9)holes
87-:3/16(:5.1)holes
6
Address board
Connection No.
Address setting digit
Mode selection
*3 Address board is protected
by a plastic cover.
Remove the screw holding
the cover with screw-driver
at the time of address setting.
Knockout hole for
remote control wiring
Drain pipe
3/16×1-3/8(4.5×35) 4 holes
Address board
Detailed
2-3/8(60mm) or more for
left and left back piping.
Required space
Min55/64(22)
2-7/8
(74.6)
Air outlet
3/32(2.5)
5/32(4)
5°
1-25/32(45)
13/32(10)
Knockout hole for
left piping
Air intake
4-9/16(116)
)
12
2(R
5/3
R1
3°
5)
R1
2(
9/3
R1
2-1/8(54)
1/4
(7)
Gas pipe
Liquid pipe
20-25/32(520)
R5
/16
(R8
)
Air outlet
(Direction)
4-11/32(110)
17-23/32(450)
Detailed figure dwg (ABC)
(Knockout hole)
1-7/16(37.8)
Air outlet
27-3/8(695)
Air outlet
Air intake
25-3/16(640)
31/32(24.4)
Terminal block
Address board Air intake
(Direction)
3-11/32(85)
3
WIRING DIAGRAM
PKFY-P08NBMU-E
Symbol
MF
MV
LEV
TB2
TB5
TH21
(32°F/15k,77°F/5.4k)
(32°F/15k,77°F/5.4k)
(32°F/15k,77°F/5.4k)
9
SW5
(RED) 4
ADDRESS
CN43 1
230V
SW1
1 2 3 4 5 6 7 8 9 10
CN52
SW3
1
4
1
8
CN81
CN42
ADDRESS
ADDRESS
(RED)
(RED)
12345678910 1234
3 1
CN32
1
1 2
CN2M
M-NET
(BLU)
1 3
1 2
CN3A
CN20
MAINTAKE
REMOCON (RED)
(BLU)
4
CN41
FAN
(GRN)
1
1 3
CN35P
(BLU)
ZNR
5
CN53P
(RED)
F.C
1
3
1
CN35M
(BLU)
5 6
4
5 6
See Fig.1
5
1
CN53M LED2
(RED)
LED1
I.B
P.B
Note
1. At servicing for outdoor unit, always follow the wiring diagram of outdoor unit.
2. In case of using MA-remote controller, please connect MA-remote controller cable in an accessory
to the connector 1 2 . (Remote controller wire is non-polar.)
3. In case of using M-NET, please connect to TB5 (Transmission line is non-polar.)
4. Symbols used in wiring diagram above are,
: terminal block,
: connector
5. The setting of the SW2 dip switches differs in the capacity. For the detail, refer to the Fig. 1.
6. Please set the switch SW5 according to the power supply voltage.
Set SW5 to 230V side when the power supply is 230 volts.
When the power supply is 208 volts, set SW5 to 208V side.
LED1
Main power supply
LED2
Power supply for
MA-Remote controller
MODELS
P06
SW2
ON
OFF
Function
Main power supply (indoor unit: 208-230V)
power on
lamp is lit
Power supply for MA-Remote controller
on
lamp is lit
P08
1 2 3 4
<Fig. 1>
SW2
MODELS
ON
OFF
1 2 3 4
<+>Use copper supply wires.
7
GRN /YLW
6
CND 1
(RED)
U
3
PULL
BOX
GR
FUSE
(16A)
BREAKER
(16A)
POWER SUPPLY
208/230V 60Hz
C1
1
BRANCH
No.
4
RED
1 2
1 2
CN29 CN21
GAS LIQUID
(BLK) (WHT)
9
CN90
WIRELESS
(WHT)
ON
OFF
LED on indoor board for service
Mark
Meaning
<+ >
TB2
L1
L2
BLU
M
1~
WHT
1
5
SW2
TO NEXT
INDOOR UNIT
1 2
BLK
t°
F0 1 2
BCD
7 8
4
1s
DIGIT
1
8
SW14
E
2 3
10ths
DIGIT
0 1
3456
9
2 3
7 8
SW11
CN51
5
4
(RED) 8
ADDRESS
CN82
789A
0 1
t°
ORN
1
1 CN5V 5
VANE
(BLU)
TO OUTDOOR UNIT
BC CONTROLLER
M-NET REMOTE CONTROLLER
DC24-30V
M1 M2 TB5
WHT
YLW
ORN
BLU
RED
BRN
A.B
9
TO MA-REMOTE
CONTROLLER
DC8.7-13V
MF
1 CN60 6
LEV
(WHT)
SW12
TH22 TH21
MV
t°
BZ
ON
OFF
TH23
CNB
LED1 LED2
208V
M
Name
Address board
Mode selection
Switch
Voltage selection
Address setting 1s digit
Address setting 10ths digit
Branch No.
Wireless remote controller board
Receving unit
Buzzer
LED(Operation indicator:Green)
LED(Preparation for heating:Orange)
Emergency operation (Heat)
Emergency operation (Cool)
RED
6
9
RU
RED 1
WHT
BLU
ORN
YLW 5
5
SW2
Pipe temp.detection/Gas
TH23
W.B
SW1
Pipe temp.detection/Liquid
TH22
M
LEV
Symbol
A.B
SW1
SW5
SW11
SW12
SW14
W.B
RU
BZ
LED1
LED2
SW1
SW2
Name
Fan motor
Vane motor
Linear expansion valve
Terminal Power supply
block
Transmission
Thermistor Room temp.detection
BLU
Legend
Symbol
Name
Indoor controller board
I.B
CN32 Connector Remote switch
Centrally control
CN51
Remote indication,
CN52
External heater
Capacity code
SW2 Switch
SW3
Mode selection
P.B
Indoor power board
ZNR Varistor
FUSE Fuse (6A 250V)
F.C Fan phase control
C1 Capacitor (Fan motor)
BLU
PKFY-P06NBMU-E
ORN
4
FUSE
250V
6A
5
REFRIGERANT SYSTEM DIAGRAM
PKFY-P06NBMU-E
PKFY-P08NBMU-E
Gas pipe temperature thermistor
TH23
Gas pipe
Strainer
(#100mesh)
Liquid pipe temperature thermistor
TH22
Strainer
(#100mesh)
Heat exchanger
Room temperature thermistor
TH21
Liquid pipe
Linear expansion
valve
Strainer
(#100mesh)
Unit: mm(inch)
Item
Models
PKFY-P06/08NBMU-E
Gas pipe
{12.7 (1/2”)
Liquid pipe
{6.35 (1/4”)
8
Flare
6
MICROPROCESSOR CONTROL
INDOOR UNIT CONTROL
6-1. COOL OPERATION
<How to operate>
Press POWER ON/OFF button.
Press the operation MODE button to display COOL.
Press the TEMP. button to set the desired temperature.
NOTE: The set temperature changes 2°F when the
or
pressed one time. Cooling 67 to 87°F
TIME SUN MON TUE WED THU FRI SAT
TIMER
Hr
ON
AFTER
AFTER OFF
ERROR CODE
FUNCTION
FILTER
ûFûC
ûFûC
WEEKLY
SIMPLE
AUTO OFF
ONLY1Hr.
TEMP.
MENU
BACK
PAR-21MAA
MONITOR/SET
ON/OFF
ON/OFF
FILTER
DAY
CLOCK
Control modes
1. Thermoregulating
function
button is
CHECK TEST
OPERATION
CLEAR
Control details
1-1. Thermoregulating function (Function to prevent restarting for 3 minutes)
• Room temperature
desired temperature + 2°F ···Thermo ON
• Room temperature
desired temperature ···Thermo OFF
Remarks
1-2. Anti-freezing control
Detected condition : When the liquid pipe temp. (TH22) is 32°F or less in 16
minutes from compressors start up, anti-freezing control
starts and the thermo OFF.
Released condition : The timer which prevents reactivating is set for 3 minutes,
and anti-freezing control is cancelled when any one of the
following conditions is satisfied.
Liquid pipe temp. (TH22) turns 50°F or above.
The condition of the thermo OFF has become complete
by thermoregulating, etc.
The operation modes became mode other than COOL.
The operation stopped.
3. Vane
(up/down vane change)
By the remote controller setting (switch of 4 speeds)
Type
Fan speed notch
4 speeds type
[Low], [Mid2], [Mid1], [High]
(1) Initial setting: Start at COOL mode and horizontal vane.
(2) Vane position:
Horizontal →Downward A →Downward B →Downward C
→
2. Fan
(3) Restriction of the downward vane setting
When setting the downward vane A, B or C in [Mid] or [Low] of the fan speed
notch, the vane changes to horizontal position after 1 hour have passed.
9
· "ONLY 1 Hr"
appears on the
wired remote
controller.
6-2. DRY OPERATION
TIME SUN MON TUE WED THU FRI SAT
TIMER
Hr
ON
AFTER
AFTER OFF
ERROR CODE
FUNCTION
FILTER
ûFûC
ûFûC
WEEKLY
SIMPLE
AUTO OFF
ONLY1Hr.
TEMP.
MENU
BACK
PAR-21MAA
MONITOR/SET
ON/OFF
ON/OFF
CHECK TEST
OPERATION
CLEAR
Control modes
Remarks
Control details
1. Thermo regulating 1-1. Thermo regulating function (Function to prevent restarting for 3 minutes)
Setting the Dry thermo by the thermo regulating signal and the room
function
temperature (TH21).
Dry thermo ON Room temperature desired temperature + 2°F
Dry thermo OFF Room temperature desired temperature
Room
temperature
Dry thermo Dry thermo
ON
OFF
Thermo regulating signal Room temperature (T1) time (min) time (min)
3 min. passed since starting operation
ON
Over 64°F
T1
83°F
9
3
83°F > T1
79°F
7
3
79°F > T1
75°F
5
3
3
3
3
10
75°F > T1
OFF
Unconditional
Dry thermo OFF
Less than 64°F
1-2. Freeze prevention control
No control function
2. Fan
button is
FILTER
DAY
CLOCK
<How to operate>
Press POWER ON/OFF button.
Press the operation MODE button to display DRY.
Press the TEMP. button to set the desired temperature.
NOTE: The set temperature changes 2°F when the
or
pressed one time. Dry 67 to 87°F
Indoor fan operation controlled depending on the compressor conditions.
Dry thermo
Fan speed notch
ON
[Low]
OFF
Excluding the following
Stop
Room temp. < 64°F
[Low]
Note: Remote controller setting is not acceptable.
Same control as COOL operation
3. Vane
(up/down vane change)
10
6-3. FAN OPERATION
<How to operate>
Press POWER ON/OFF button.
Press the operation MODE button to display FAN.
TIME SUN MON TUE WED THU FRI SAT
TIMER
Hr
ON
AFTER
AFTER OFF
ERROR CODE
ûFûC
ûFûC
WEEKLY
SIMPLE
AUTO OFF
ONLY1Hr.
TEMP.
MENU
BACK
PAR-21MAA
MONITOR/SET
FUNCTION
FILTER
ON/OFF
ON/OFF
FILTER
DAY
CLOCK
CHECK TEST
OPERATION
CLEAR
Control modes
1. Fan
Control details
Remarks
Set by remote controller.
Type
Fan speed notch
4 speeds type
[Low], [Mid2], [Mid1], [High]
2. Vane
Same as the control performed during the COOL operation, but with no restriction
(up/down vane change) on the vane's downward blow setting
11
· Same control
as COOL
operation
6-4. HEAT OPERATION
<How to operate>
Press POWER ON/OFF button.
Press the operation MODE button to display HEAT.
Press the TEMP. button to set the desired temperature.
NOTE: The set temperature changes 2°F when the
or
pressed one time. Heating 63 to 83°F.
TIME SUN MON TUE WED THU FRI SAT
TIMER
Hr
ON
AFTER
AFTER OFF
ERROR CODE
ûFûC
ûFûC
WEEKLY
SIMPLE
AUTO OFF
ONLY1Hr.
TEMP.
MENU
BACK
PAR-21MAA
MONITOR/SET
FUNCTION
FILTER
ON/OFF
ON/OFF
<Display in HEAT operation>
[DEFROST]
The [DEFROST] symbol is only displayed during the defrost operation.
[STANDBY]
The [STANDBY] symbol is only displayed during the hot adjust mode.
FILTER
DAY
CLOCK
CHECK TEST
OPERATION
CLEAR
Control modes
1. Thermoregulating
function
2. Fan
button is
Remarks
Control details
1-1. Thermoregulating function (Function to prevent restarting for 3 minutes)
• Room temperature desired temperature -2°F ···Thermo ON
• Room temperature desired temperature
···Thermo OFF
By the remote controller setting (switch of 4 speeds)
Type
Fan speed notch
4 speeds type
[Low], [Mid2], [Mid1], [High]
Give priority to under-mentioned controlled mode
2-1. Hot adjust mode
2-2. Residual heat exclusion mode
2-3. Thermo OFF mode (When the compressor off by the thermoregulating)
2-4. Cool air prevention mode (Defrosting mode)
2-1. Hot adjust mode
The fan controller becomes the hot adjuster mode for the following conditions.
When starting the HEAT operation
When the thermoregulating function changes from OFF to ON.
When release the HEAT defrosting operation
Hot adjust mode *1
*1 "STAND BY"
will be displayed
during the hot
adjust mode.
Set fan speed by the remote controller
[Low]
[Extra Low]
A
B
C
A: Hot adjust mode starts.
B: 5 minutes have passed since the condition A or the indoor liquid pipe
temperature turned 95°F or more.
C: 2 minutes have passed since the condition B. (Terminating the hot adjust mode)
2-2. Residual heat exclusion mode
When the condition changes the auxiliary heater ON to OFF (thermoregulating or
operation stop, etc), the indoor fan operates in [Low] mode for 1 minute.
· This control is
same for the
model without
auxiliary heater.
To be continued on the next page.
12
From the preceding page
Control details
Control modes
Remarks
2-3. Thermo OFF mode
When the thermoregulating function changes to OFF, the indoor fan operates in
[Extra low].
2. Fan
2-4. Heat defrosting mode
The indoor fan stops.
(1) Initial setting: OFF → HEAT···[last setting]
When changing the mode from exception of HEAT to HEAT operation
···[Downward C]
3. Vane control
(Up/down vane
change)
(2) Vane position:
→
Horizontal →Downward A →Downward B →Downward C
(3) Restriction of vane position
The vane is horizontally fixed for the following modes.
(The control by the remote controller is temporally invalidated and control by
the unit.)
•Thermo OFF
•Hot adjust [Extra low] mode
•Heat defrost mode
6-5. AUTO OPERATION [AUTOMATIC COOL/HEAT CHANGE OVER OPERATION]
TIME SUN MON TUE WED THU FRI SAT
TIMER
Hr
ON
AFTER
AFTER OFF
ERROR CODE
ûFûC
ûFûC
WEEKLY
SIMPLE
AUTO OFF
ONLY1Hr.
TEMP.
MENU
BACK
PAR-21MAA
MONITOR/SET
FUNCTION
FILTER
ON/OFF
ON/OFF
button is
FILTER
DAY
CLOCK
<How to operate>
Press POWER ON/OFF button.
Press the operation MODE button to display AUTO.
Press the TEMP. button to set the desired temperature.
NOTE: The set temperature changes 2°F when the
or
pressed one time. Automatic 67 to 83°F
CHECK TEST
OPERATION
CLEAR
Control details
Control modes
1. Initial value of HEAT mode for room temperature < Desired temperature
operation mode COOL mode for room temperature Desired temperature
2. Mode change (1) HEAT mode → COOL mode
Room temperature Desired temperature + 3°F. or 3 min. has passed
(2) COOL mode → HEAT mode
Room temperature Desired temperature - 3°F. or 3 min. has passed
3. COOL mode
Same control as cool operation
4. HEAT mode
Same control as heat operation
13
Remarks
7
TROUBLESHOOTING
7-1. HOW TO CHECK THE PARTS
PKFY-P06NBMU-E
PKFY-P08NBMU-E
Parts name
Check points
Room temperature
thermistor (TH21)
Liquid pipe temperature
thermistor (TH22)
Disconnect the connector then measure the resistance with a tester.
(At the ambient temperature 50°F~86°F)
Normal
Abnormal
4.3k~9.6k
Open or short
Refer to the next page for the details.
Gas pipe temperature
thermistor (TH23)
Measure the resistance between the terminals using a tester. (At the ambient temperature 77°F)
Vane motor (MV)
4 Orange
Normal
M
-
Red-White
2 White
1 Red
Connect pin No.
Yellow Blue
5
Black
Abnormal
-
Red-Yellow
Open or short
Measure the resistance between the terminals using a tester. (At the ambient temperature 68°F)
FAN
White
Red
-
Red-Orange
400 ± 7%
3
Fan motor (MF)
Normal
-
Red-Blue
Abnormal
Normal
1
4
White-Black
313 ± 8%
6
Red-Black
108 ± 8%
Linear expansion
valve (LEV)
Open or short
Disconnect the connector then measure the resistance value with a tester.
(Coil temperature 68°F)
CN60
White
Yellow
Orange
LEV
Blue
Red
Brown
1
2
3
4
5
6
Normal
Abnormal
(1)-(5)
(2)-(6)
(3)-(5)
(4)-(6)
White-Red Yellow-Brown Orange-Red Blue-Brown
Open or short
200 ± 10%
14
7-1-1. Thermistor
< Thermistor for lower temperature >
<Thermistor characteristic graph>
50
Room temperature thermistor (TH21)
Liquid pipe temperature thermistor (TH22)
Gas pipe temperature thermistor (TH23)
Thermistor for
lower temperature
40
Rt=15exp { 3480(
30°F
50°F
70°F
80°F
90°F
100°F
1
273+(t-32)/1.8
Resistance (kΩ)
Thermistor R0=15kΩ ± 3%
Fixed number of B=3480 ± 2%
1 )}
273
15.8kΩ
9.6kΩ
6.0kΩ
4.8kΩ
3.9kΩ
3.2kΩ
30
20
10
0
-20
0
20
40
60
80
Temperature (°F)
100
120
7-1-2. Liner expansion valve
Operation summary of the linear expansion valve
• Linear expansion valve open/close through stepping motor after receiving the pulse signal from the indoor controller board.
• Valve position can be changed in proportion to the number of pulse signals.
<Connection between the indoor controller board and the linear expansion valve>
Controller board
DC12V
Brown
6
Red
5
Φ4
Blue
4
Φ4
Φ3
Orange
3
Φ3
Φ2
Yellow
2
Φ2
Φ1
White
1
Φ1
Linear expansion valve
4
M
6
5
2
1
White Red
3
Orange
Blue
Brown
Yellow
Connector(CN60)
15
Drive circuit
<Output pulse signal and the valve operation>
Output
Output
(Phase)
1
ON
ON
OFF
OFF
[1
[2
[3
[4
3
OFF
OFF
ON
ON
2
OFF
ON
ON
OFF
4
ON
OFF
OFF
ON
Linear expansion valve operation
Note:
• When linear expansion valve operation stops, all output phase
become OFF.
• At phase interruption or when phase does not shift in order, motor
does not rotate smoothly and motor will lock and vibrate.
• When the switch is turned on, 2200 pulse closing valve signal will
be sent till it goes to point in order to define the valve position.
Open
C
D
Valve position (capacity)
Closing a valve : 1 → 2 → 3 → 4 → 1
Opening a valve : 4 → 3 → 2 → 1 → 4
The output pulse shifts in above order.
• When the valve moves smoothly, there is no sound or vibration
occurring from the linear expansion valves, however, when the
pulse number moves from to or when the valve is locked,
more sound can be heard than in a normal situation.
• Sound can be detected by placing the ear against the screw driver
handle while putting the screw driver tip to the linear expansion
valve.
Close
Open
Outdoor unit R410A model : 1400 pulse
Outdoor unit R22 model
: 2000 pulse
Opening a valve all the way
A
E
Close
B
Pulse number
Extra tightening (200~800 pulse)
Trouble shooting
Symptom
Check points
Countermeasures
Operation circuit
failure of the micro
processor
Disconnect the connector on the controller board, then con- Exchange the indoor connect LED for checking.
troller board at drive circuit
6
5
failure.
4
3
2
1
1kΩ LED
When power is turned on, pulse signals will be output for 10
seconds. There must be some defects in the operation circuit
if the LED does not light while the signals are output or keeps
lighting even after the signals stop.
Linear expansion
valve mechanism is
locked.
Motor will idle and make a ticking noise when the motor is
operated while the linear expansion valve is locked.
This ticking sound is the sign of the abnormality.
Exchange the linear expansion valve.
Short or breakage
Measure the resistance between each coil (white-red, yellow- Exchange the linear expanof the motor coil of
brown, orange-red, blue-brown) using a tester. It is normal if sion valve.
the linear expansion the resistance is in the range of 200Ω ±10%.
valve
Valve does not close To check the linear expansion valve, operate the indoor unit If large amount of refrigercompletely.
in fan mode and at the same time operate other indoor units ant is leaked, exchange
in cooling mode, then check the pipe temperature <liquid
the linear expansion valve.
pipe temperature> of the indoor unit by the
outdoor multi controller board operation
monitor. During fan operation, linear expansion valve is closed completely and if there
Thermistor
(Liquid pipe) is any leaking, detecting temperature of
the thermistor will go lower. If the detected
Linear
temperature is much lower than the temexpansion
valve
perature indicated in the remote controller,
it means the valve is not closed all the way.
It is not necessary to exchange the linear expansion valve, if
the leakage is small and not affecting normal operation.
Wrong connection
of the connector or
contact failure
Check the color of lead wire and missing terminal of the con- Disconnect the connector
nector.
at the controller board,
then check the continuity.
16
7-2. Function of Dip switch
PKFY-P06NBMU-E
PKFY-P08NBMU-E
Switch Pole
Operation by switch
Function
ON
OFF
1
Thermistor<Room temperature>
position
Built-in remote controller
Indoor unit
2
Filter clogging detection
Provide
Not provide
3
Filter cleaning sign
4
Fresh air intake
SW1
5
Mode
selection 6
7
Remarks
Address board
<Initial setting>
ON
OFF
2,500 hr
100 hr
Not effective
Not effective
1 2 3 4 5 6 7 8 9 10
+2
Switching remote controller display Thermo ON signal indication Fan output indication
Fan operation at Heating mode Thermo ON operation at
heating mode
Humidifier control
Extra low +1
8
Air flow set in case of heat Low +1
thermo OFF
Setting air flow +1
9
Auto restart function
Effective
Not effective
Power ON/OFF by breaker Effective
Not effective
10
Effective
timing
Models
SW2
Capacity
1~6
code
switch
P06
Under
suspension
SW1-7 SW1-8 Fan speed
OFF OFF Extra low
ON
OFF Low
OFF
ON Setting air flow
ON
ON Stop
Depends on SW1-7
+2 It is impossible to intake
the fresh air.
Indoor controller board
SW2
ON
Before
power
supply
ON
OFF
1 2 3 4
P08
NOTE:
+1
ON
OFF
1 2 3 4
1
Heat pump/Cool only
2
Louver
3
Vane
SW3 4
Function
selection 5
6
Cooling only
—
Indoor controller board
—
Available
Vane swing
Vane horizontal angle
Heat pump
Not available
—
—
Second setting +3
First setting
Vane cooling limit angle setting +1 Horizontal angle
Down B, C
7
Changing the opening of linear
expansion valve
Not effective
8
Heating 4 degree (4 °C) up Not effective
9
Target superheat setting +2
—
—
10
Tartget subcool setting +2
—
—
Effective
Effective
17
<Initial setting>
Under
suspension
ON
OFF
1 2 3 4 5 6 7 8 9 10
+1 At cooling mode, each angle
can be used only 1 hour.
+2 Please do not use SW3-9,10
as trouble might be caused
by the usage condition.
+3 Second setting is the same as
first setting.
1
CDE
AB
789
Address board
<Initial setting>
SW14
CDE
AB
F01
789
Rotary switch
Before
power
supply
ON
23
Jumper
90 1
• To operate each indoor unit by each remote controller when installed 2 indoor
units or more are near, Pair No. setting is necessary.
.
Pair No. setting is available with the 4 patterns (Setting patterns A to D).
Make setting for J41, J42 of indoor controller board and the Pair No. of
wireless remote controller.
• You may not set it when operating it by one remote controller.
Setting for indoor unit
Cut jumper wire J41, J42 on the indoor controller board according to the
table below.
Wireless remote controller pair number:
Setting operation
Under
1. Press the SET button (using a pointed implement). Check that the
operation
remote controller's display has stopped before continuing.
or
MODEL SELECT flashes, and the model No. (3 digits) appears (steadily-lit).
2. Press the MINUTE button twice. The pair number appears flashing.
suspension
3. Press the temperature
buttons to select the pair number to set.
4. Press the SET button (using a pointed implement). The set pair number is
displayed (steadily-lit) for 3 seconds, then disappears.
Setting pattern
Indoor controller
jumper wire
Pair No. of wireless
remote controller
J41
J42
0
—
—
A
Initial setting
1
—
—
Cut
B
2
—
Cut
—
C
3
—
Cut
Cut
D
Pair No.4-9 of wireless remote controller is setting pattern D.
18
45 6
Wireless
remote
controller
Pair No.
How to set branch numbers SW14 (Series R2 only)
Match the indoor unit’s refrigerant pipe with
the BC controller’s end connection number.
Remain other than series R2 at "0".
SW11
90 1
23
J41, J42
45 6
SW14
Branch
No.
Setting
23
F01
SW12
23
SW14
<Initial setting>
78
45 6
45 6
10
Address board
How to set addresses
Example : If address is "3", remain SW12
(for over 10) at "0", and match SW11 (for 1 to 9)
with "3".
78
78
78
23
Rotary Switch
90 1
45 6
SW11
90 1
Remarks
45 6
SW12
23
SW11
1s digit
address
setting
SW12
10ths digit
address
setting
Effective
timing
Operation by switch
Switch
<Initial setting>
Pattern A
Pair No.
MODEL SELECT
FAN
AUTO STOP
VANE
AUTO START
CHECK LOUVER
SET
h
min
TEST RUN
SET button
Temperature
button
TEMP
ON/OFF
MODE
Model No.
RESET
CLOCK
Minute
button
7-3. TEST POINT DIAGRAM
7-3-1. Indoor controller board
PKFY-P06NBMU-E
PKFY-P08NBMU-E
CN5V
Vane motor output
(MV)
CN90
Connected to the wireless
remote controller board (W.B)
CN81
Connected to the
address board (CN82)
CN29
Pipe temperature
thermistor/Gas (TH23)
CN21
Pipe temperature
thermistor/Liquid (TH22)
CN60
Linear expansion valve
output (LEV)
CN42
Connected to the
address board (CN43)
CN3A
Connected to the
MA-Remote controller
Between 1 to 3 8.7-13V DC
(Pin1 (+))
CN51
Centrally control
CN20
Room temperature
thermistor (TH21)
CN52
Remote indication
External heater
SW3
Mode selection
CN41
Connector
(HA terminal-A)
J41, J42
Wireless remote controller
Pair No. setting
CN32
Connector
(Remote switch)
JP105
Model setting
LED2
Power supply for
MA-Remote controller
SW2
Capacity setting
CN35M
Connected to the indoor
power board (CN35P)
19
CN53M
Connected to the indoor power board (CN53P)
Between 1 to 2 24-30V DC (non-polat)
Between 3 to 5 12.5-13.7V DC (Pin3 (+))
Between 4 to 5 11.5-12.7V DC (Pin4 (+))
FAN
Fan motor output (MF)
7-3-2. Indoor power board
PKFY-P06NBMU-E
PKFY-P08NBMU-E
CND
Power supply for
indoor controller board
Between 1 to 3 208/230V AC
CN2M
Connected to the terminal block (TB5)
(M-NET transmission connecting wire)
24-30V DC (non-polar)
FUSE
6A 250V
CN35P
Connected to the indoor controller board
(CN35M)
CN53P
Connected to the indoor controller board
(CN53M)
Between 1 to 2 24-30V DC (non-polar)
Between 3 to 5 12.5-13.7V DC (Pin3 (+))
Between 4 to 5 11.5-12.7V DC (Pin4 (+))
LED1
Main power supply
(Indoor unit : 208/230V)
7-3-3. Address board
PKFY-P06NBMU-E
PKFY-P08NBMU-E
SW1
1 2 3 4 5 6 7 8 9 10
BCD
78
78
4 56
4 56
Address setting
10ths DIGIT
EF0 12
3456
23
SW12
23
90 1
90 1
789A
Function setting
SW11
SW14
Address setting
1s DIGIT
Branch No.
20
8
DISASSEMBLY PROCEDURE
PKFY-P06NBMU-E
Be careful when removing heavy parts.
PKFY-P08NBMU-E
OPERATION PROCEDURE
PHOTOS & ILLUSTRATIONS
1. REMOVING THE LOWER SIDE OF THE INDOOR UNIT
FROM THE INSTALLATION PLATE
Figure 1
When there is removing plate
(1) Remove the corner box at right lower side of the indoor
unit and remove the removing plate from the corner box.
(Figure 3)
(2) Insert the removing plate at the back side of the corner
box to remove the indoor unit.
(3) Remove the hook by pulling the lower side of the indoor
unit down as shown in the Figure 1.
When there is no removing plate or it cannot be used for
some reason.
(1) Remove the front panel.
(2) Insert the screw driver to the corner hole at both left and
right side as shown in the Figure 2.
(3) Push it up, then pull down the lower side of indoor unit and
remove the hook.
Figure 2
Push
Indoor unit
removing plate
Insert
the edge
Corner hole
Be careful
not to damage
the airflow
adjustment
plate with the
screw driver. Push
Pull
Figure 3
Corner box
2. REMOVING THE FRONT PANEL
Photo 1
* Before removing the front panel, leave the open space at
upper side of the vane approximately 2 to 3 cm.
(1) Remove the 3 screw caps then remove the 3 set screws.
(Refer to the Photo 1)
(2) Remove the grille.
(3) Remove the left side of the front panel, then right side.
(4) After removing the lower side of the front panel a little,
remove it as pulling the upper side toward you.
* Please pay attention to the nozzle assembly.
INSTALLING THE FRONT PANEL
(1) Insert the lower side of the front panel under the vane.
(2) Set the upper side of the front panel. (Figure 4)
(3) Set the lower side of the front panel then fix it with the
screws.
(4) Press the area indicated as arrow sign and set it to the air
conditioner unit.
(5) Attach the screw caps.
Grille
Front panel
Set screws
Vane
Figure 4
(2)
(4) Push
(3)
21
Down
OPERATION PROCEDURE
PHOTOS
Electrical box cover
3. REMOVING THE INDOOR CONTROLLER BOARD AND
INDOOR POWER BOARD
Photo 2
(1) Remove the front panel. (Refer to 2)
(2) Remove the electrical box cover (screw 4 × 10).
(Refer to the Photo 2)
INDOOR CONTROLLER BOARD
(1) Disconnect the following connectors on the indoor
controller board.
(connector in front of)
CN60, CN5V, CN90, CN29, CN21
CN42, CN81, CN3A, CN20
(2) Pull out the indoor controller board toward you, then
disconnect the rest of connectors.
CN53M, CN35M (See the Photo 3)
Screw cap
Electrical box
INDOOR POWER BOARD
(1) Disconnect the following connectors on the indoor power
board.
FAN, CN53P, CN35P, CN2M, CND
(2) Remove the earth wire for TAB1.
(3) Pull out the indoor power board toward you.
(See the Photo 3)
Photo 3
Indoor controller board
Indoor power
board
Electrical box
Room temperature
thermistor cover
4. REMOVING THE ELECTRICAL BOX
Photo 4
(1) Remove the front panel. (Refer to 2)
(2) Remove the electrical box cover. (See the Photo 2)
(3) Pull the nozzle assembly toward you as opening the catch
Indoor controller board
of the nozzle assembly. (See the Photo 5)
Linear expansion valve
(4) Disconnect the indoor/outdoor transmission wiring of TB5.
(5) Disconnect the power supply wiring of TB2.
(6) Disconnect the relay connector of MA-remote controller.
Liquid pipe temp.
(7) Disconnect the following connector on the indoor controller thermistor (TH22)
board.
CN60, CN5V, CN29, CN21, CN90, (CN3A)
(8) Disconnect the connector (FAN) on the indoor power board.
(9) Remove the ground wire fixing screw.
(10) Pull the disconnected lead wire out from the electrical box.
(11) Push up the upper fixture catch to remove the box, then
Gas pipe temp.
pull the lower fixture and remove it from the box fixture.
thermistor (TH23)
Indoor power
board
MA-remote
controller
connector
Terminal block
(TB5)
Terminal block
(TB2)
Ground wire set screw
22
OPERATION PROCEDURE
PHOTOS
5. REMOVING THE NOZZLE ASSEMBLY AND DRAIN HOSE
(1) Remove the front panel (Refer to 2).
(2) Remove the electrical box cover.
(3) Disconnect the connector (CN5V) on the indoor controller
board.
(4) After unhook the right side of the corner box, press the
upper left side and remove the corner box.
(5) Remove the nozzle assembly from the fixture.
(See the Photo 5)
(6) Remove the drain hose.
6. REMOVING THE LINE FLOW FAN AND THE FAN MOTOR
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
Remove the front panel. (Refer to 2)
Remove the nozzle assembly. (Refer to 5)
Remove the electrical parts box.
Remove the fixture while pressing the right side of motor
fixture catch. (See the Photo 6)
Remove the left side of the motor fixture.
Loosen the screw which fixes the line flow fan to the fan
motor, then remove the fan motor by sliding it to the right
side. (See the Photo 6)
Pull the left-hand side of the heat exchanger toward you.
(See the Photo 7)
Remove the line flow fan.
Photo 5
Heat exchanger
Electrical box
Drain hose
fixture
Nozzle assembly
fixture
Heat exchanger
Photo 6
Drain hose
Fan motor
fixture (right)
fixture (left)
Line flow fan
fixture set screws
set screws
Drain hose
Nozzle assembly
Photo 7
Heat exchanger
Heat exchanger
fixture (left)
Photo 8
7. REMOVING THE VANE MOTOR
(1) Remove the front panel.
(2) Remove the screw of the electrical parts box cover, and
remove the cover.
(3) Remove the 2 screws of the vane motor.
Disconnect the relay connector and remove the motor
from the shaft.
(4) Disconnect the vane motor connector (CN5V) on the indoor
controller board.
8. REMOVING THE LIQUID PIPE THERMISTOR AND GAS
PIPE THERMISTOR
Remove the front panel. (Refer to 2)
Remove the electrical box cover.
Remove the coil cover.
Cut the wiring fixed band.
Remove the liquid pipe thermistor and gas pipe thermistor.
(See the Photo 9)
(6) Disconnect the connector (CN29) (CN21) on the indoor
controller board.
Heat exchanger
Vane motor
Vane motor fixing
screws
Nozzle assembly
Photo 9
Heat exchanger
Liquid pipe thermistor
(1)
(2)
(3)
(4)
(5)
23
Gas pipe
thermistor
Electrical box
TM
HEAD OFFICE : TOKYO BLDG., 2-7-3, MARUNOUCHI, CHIYODA-KU TOKYO 100-8310, JAPAN
Copyright 2009 MITSUBISHI ELECTRIC ENGINEERING CO., LTD.
Distributed in Apr. 2009 No. OCH461 PDF 7
Made in Japan
New publication, effective Apr. 2009
Specifications subject to change without notice