Download Craftsman 113.20680 Specifications

FULL ONE YEAR
WARRANTY
ON CRAFTSMAN
JOINTER/PLANER
year from the date of purchase, this Craftsman Jointer/Planer fails due to a defect in material
rs will repair it, free of charge.
,VAtLABLE
BY SIMPLY CONTACTING
THROUGHOUT THE UNITED STATES.
THE NEAREST
SEARS STORE
you may also have other rights which vary from state to
CO,; Sears Tower,
SEARS,
general
safety
the
owner's
application
and
potential
hazards
2.:GROUND
manual
Learn
as the
its
Keep proper
in
proper
adjustment
before
blades,
KEYS
Cluttered
areas
and
must not be Slippery
Provide
adequate
tools
rain;
visitors-should
Consult
work
19: NEVER
space.
i:
AWAY
be kept
a safe distance
from
work
DO not
8. MAKE WORKSHOP
-- with
padlocks,
starter keys,
9. DON'T
or
by
removing
20. CHECK
Before
FORCE TOOL
it will do the job better
it was designed.
10. USE RIGHT
force
designed
switches,
and safer at the rate for which
will
to do
a job
it was not
for.
11. WEAR PROPER APPAREL
Do not
wear
loose
clothing,
gloves,
(rings, wrist
watches}
to get caught
Nonslip
footwear
is recommended.
hair covering
to contain
tong hair.
above the elbow.
12. USE SAFETY
for
as
before
plugging
for
recommended
that accompany
accessories may
ON TOOL
above
is tipped
or near the tool
or if the
such that
to stand on the too_ to reach them.
DAMAGED
PARTS
use of the too!,
should
operate
Check
or attachment
manual
materials
further
is damaged
TOOL
tool
store
such
ACCESSORIES
owner's
STAND
it is necessary
KID-PROOF
master
position
i ::":i Seri0us injury could occur if the toot
cuttin£ tool is accidentally
contacted.
area.
Don't
the
accessories
accessories,
Fol}ow
the instructions
the accessories. The use of improper
cause hazards.
ENVIRONMENT
safest
and
STARTING
is in "OFF"
18. USE RECOMMENDED
Floor
in damp or wet locations
or
Keep work
area well lighted;
surrounding
7. KEEP CHILDREN
All
accidents.
due to wax or sawdust.
6;:!AV01D DANGEROUS
D0n't
use power
expose them
to
invite
best and
lubricating
for
changing
ACCIDENTAL
Make sure switch
in,
CLEAN
benches
for
TOOLS
servicing;
when
bits, cutters, etc.
17. AVOID
Form habit of checking
to see that keys and adjusting
wrenches are removed
from tool before turning
it on.
5: KEEP WORK AREA
at all times,
TOOLS WITH CARE
16. DISCONNECT
and
alignment,
4. REMOVE ADJUSTING
AND WRENCHES
and balance
Keep
tools
sharp
and clean
performance.
Follow
instructions
changing accessories.
IN PLACE
and
footing
15. MAINTAIN
green wire to a live terminal.
order,
fools
14. DON'T OVERREACH
ALL TOOLS
working
power
Use clamps or a vise to hold work when practical
It's
safer than using your hand, frees both hands to operate
tool.
specific
This tool is equipped
with an approved
3.conductor
c0rd and a 3-prong
grounding
type plug to fit the
proper grounding
type receptacle
The green conductor
in the cord is the grounding
wire. Never connect the
in
IL 60684
13. SECURE WORK
carefully.
limitations
as well
peculiar to this tool.
3; KEEP GUARDS
Chicago.
for
instructions
1.:KNOW YOUR POWER TOOL
Read
BSC 41-3.
be carefully
properly
alignment
a guard
and perform
of moving
or other
checked
its intended
parts,
part that
to ensure that
binding
it
function.
of moving
parts, breakage
conditions
that
of parts,
mounting,
and any other
may ,affect its operation.
A guard or
other
is damaged
part
that
should
be properly
repaired
or replaced.
neckties
or jewelry
m moving
parts.
Wear protective
Roll long sleeves
21. DIRECTION
Feed work
of rotation
GOGGLES
OF FEED
into a blade or cutter against
of the blade or cutter only.
22. NEVER LEAVE
UNATTENDED
WearSafety
goggles (must comply with ANS!
Z87.1 )
at all times,; Ats0, use face or dust mask if cutting
operation
is dusty, and ear protectors (plugs or mUffs)
during extended
periods of operation:
Turn power off.
complete
stop.
2
TOOL
Don't
the direction
RUNNING
leave
tool
until
it comes
to a