Download Philips Clon99-BKI Network Card User Manual
Transcript
SMARTLOADER Clon99-BK Instructions for use 3135 015 14061 TABLE OF CONTENTS KNOW THESE SAFETY SYMBOLS Table of Contents ..................................................................2 Safety/Precautions.................................................................2 Introduction...........................................................................2 t Getting Started ......................................................................3 Battery Installation................................................................3 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN s CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Connecting the Clon99-BK Box...........................................4 Erasing Memory ...................................................................5 Reading Memory ..................................................................6 t This “bolt of lightning” indicates uninsulated material within your unit which may cause an electrical shock. For the safety of everyone in your household, please do not remove product covering. Programming (Writing) Memory to a TV ............................7 Running a System Test .........................................................8 Exiting the Menu System .....................................................9 s The “exclamation point” calls attention to features for which you should read the enclosed literature closely to prevent operating and maintenance problems. Programming with the On-Set Keyboard ...........................10 On-Screen Displays for Non-Global TV using the Transmitter ..........................................................................11 WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. On-Screen Displays for Non-Global TV using the On-Set Keyboard.............................................................................12 CAUTION: To prevent electric shock, match wide blade of plug to wide slot, and fully insert. Index ...................................................................................12 ATTENTION: Pour éviter les chocs électrques, introduire la lame la plus large de la fiche dams la borne correspondante de la prise et pousser jussssqu'au fond. Optimum Performance of the Clon99-BK SmartLoader box is obtained by plugging it into an ITV set that is already turned on. For Customer Use: Enter below the Serial No. which is located on the product. Retain this information for future reference. Model No Serial No. INTRODUCTION Assembling and operating your Philips Clon99-BK SmartLoader is designed to be an easy process. The purpose is to allow you to more easily program a number of televisions using just a few simple steps. The Clon99-BK SmartLoader replaces the RL-5180CK model. The Clon99-BK SmartLoader is compatible with all Philips SmartPort and ClonPort TV sets including Global 1999 models from the PL9XXX, PC9XXX, and PA9XXX series. Please be sure that you have the following material before beginning any procedures with the Clon99-BK SmartLoader box. • • • • • A television capable of sending and receiving Clon99-BK SmartLoader information on TV settings. One 9-volt battery (for the Clon99-BK SmartLoader). Remote Control RG4172BK (T374AH). Three AA batteries for the remote control. Cable (6-conductor included with the Clon99-BK SmartLoader) Please thoroughly read all the procedures listed within this booklet before starting any process. Clon99™, SmartCard™, SmartLoader™, SmartPort™ ClonPort™ are registered trademarks of the Philips Consumer Electronics Company. © 1999 Philips Consumer Electronics Company. 2 GETTING STARTED CAUTION: Failure to follow these instructions may result in product damage. Please read all instructions before beginning. Clon99-BK SmartLoader Battery Installation Battery installation Clon99-BK SmartLoader Before operating the Clon99-BK SmartLoader, load a 9-volt battery into the compartment in the bottom of the Clon99-BK SmartLoader. Slide the Battery Cover off the bottom of the Clon99-BK SmartLoader 1 BEGIN Slide the compartment lid in the direction indicated by the triangle. Attach and insert a 9 volt battery Plug the battery into the battery cable, then place the battery in the compartment. Replace the compartment lid. 2 Battery installation RG4172BK (T374AH) Remote Control Replace the Battery Cover Before operating the Remote Control, please load the three AA batteries into the compartment in the bottom of the Remote Control. 3 BEGIN Press the tab on the battery lid and lift off the remote. Following the diagrams inside the Remote Control, load the batteries. Then replace the battery lid. Point the Remote Control at the TV and see if it turns on the TV. If it does not, repeat this step. RG4172BK (T374AH) Remote Control Battery Installation SMART HELP Remember. Always be sure to check the polarity of the batteries before inserting them in the Clon99-BK SmartLoader or the RG4172BK (T374AH) Remote Control. Press the tab on the Battery Cover and lift it off. 3 Load 3 “AA” volt batteries Replace the Battery Cover CONNECTING THE CLON99-BK SMARTLOADER Optimum Performance of the Clon99-BK SmartLoader box is obtained by plugging it into an ITV set that is already turned on. Clon99-BK SmartLoader Connection 1 Power button on the front of an ITV. BEGIN Press the POWER button to turn the ITV ON. Plug one end of the cable into the jack provided on the Clon99-BK SmartLoader. Plug the other end into the jack provided on the back of the TV. The TV’s jack is next to the Antenna Input terminal and may be labeled various ways such as; Smart Port, Clone Port, etc. POWER Clon99-BK SmartLoader EXTERNAL SPEAKER 75Ω ANT/ CABLE SMART PLUG 2 Push the Slide Switch to the ON position. The red LED should light. (If the TV is turned off, it should turn on within 15 seconds.) EXTERNAL SPEAKER Rear jack panel of ITV 75Ω ANT/ CABLE SMART PLUG Within 20 seconds, the Clon99BK SmartLoader on-screen display should appear. If the display does not appear, check the connections and push the Slide Switch to the ON position again. If there is still no response from the SmartLoader, replace its 9-volt battery. 3 Cable 4 Once the Clon99-BK SmartLoader on-screen display appears, press the POWER button on the RG4172BK (T374AH) Remote Control. The SmartLoader Setup Menu should appear. LED Clon99-BK SmartLoader ON/OFF slider switch 5 6 Clon99-BK SmartLoader Setup Menu Clon99-BK SmartLoader On-Screen Display PHILIPS SMARTLOADER 99 Copyright PCEC 1999 System Version D.0 PN 3135 019 01681 Philips SmartLoader 99 System Version D.0 SLEEP CT SELE ! M ~ CH A/CH 1 - Read TV 2 - Write TV With Settings VOL D E MUT C A F E 6 - Exit SmartLoader Stored Memory Type 01, 04 4 3 2 1 5 4 T RESE 5 - System Test 6 G B 3 - Write TV Without Settings 4 - Erase SmartLoader Memory PRESS POWER TO BEGIN Press the POWER button on the remote control. T A LL RLIECGH 6 8 7 9 0 CC TV E CDGD P TV ER POW T GUES SETU DCM P SETU ERASING MEMORY OR DATA ERASE MEMORY To read and save the television memory, it is first necessary to erase any currently saved data in the Clon99BK SmartLoader. If the “Stored Memory Type” indicates no data is saved currently, you may bypass the ERASE MEMORY operation and move directly to the READ MEMORY operation. 1 PHILIPS SMARTLOADER 99 Copyright PCEC 1999 System Version D.0 PN 3135 019 01681 BEGIN RECALL SLEEP With the Clon99-BK SmartLoader on-screen display showing, press the POWER button on the remote control The Setup Menu will appear. Press the Number 4 button on the Remote Control to select the 4th option “Erase SmartLoader Memory.” PRESS POWER TO BEGIN SELECT - + M 2 A/CH VOL CH Philips SmartLoader 99 System Version D.0 1 - Read TV 2 - Write TV With Settings MUTE 3 - Write TV Without Settings 4 - Erase SmartLoader Memory A The screen will ask “Erase?” Press the 0 button on the remote to confirm and begin the procedure. RESET The screen will indicate “Memory Erased” when the data has been erased for the Clon99-BK SmartLoader. B C D E F G 1 2 3 4 5 6 7 8 9 5 - System Test 6 - Exit SmartLoader 2 Stored Memory Type 01, 04 3 CC CH GDE Philips SmartLoader 99 System Version D.0 1 - Read TV 2 - Write TV With Settings 0 3 - Write TV Without Settings 4 - Erase SmartLoader Memory POWER TV TV DCM GUEST SETUP SETUP 5 - System Test 6 - Exit SmartLoader Erase? Press 0 to confirm 3 1 Philips SmartLoader 99 System Version D.0 1 - Read TV 2 - Write TV With Settings 3 - Write TV Without Settings 4 - Erase SmartLoader Memory 4 5 5 - System Test 6 - Exit SmartLoader Memory Erased READING MEMORY OR DATA READ MEMORY Once the memory has been erased, the Clon99-BK SmartLoader is ready to read a television’s memory. Follow the steps below to complete the procedure. 1 BEGIN With the Clon99-BK SmartLoader on-screen display showing, press the POWER button on the remote control. Copyright PCEC 1999 System Version D.0 PN 3135 019 01681 RECALL SLEEP The Setup Menu will appear. Press the Number 1 button on the Remote Control to select the first option “Read TV.” PRESS POWER TO BEGIN SELECT - + M 2 A/CH The on-screen display will ask, “Read?” Press the 0 button to confirm and begin the Read procedure. VOL CH Philips SmartLoader 99 System Version D.0 1 - Read TV 2 - Write TV With Settings MUTE 3 - Write TV Without Settings 4 - Erase SmartLoader Memory A The on-screen menu will reading blocks of data on the bottom of the display. RESET Once the “Read” procedure is complete, “Finished Reading Memory” will appear at the bottom of the display. Disconnect the SmartLoader cable from the back of the TV to complete the “Read TV” operation or another Numbered button to choose a different option. PHILIPS SMARTLOADER 99 2 B C D E F G 1 2 3 4 5 6 7 8 9 CC 5 - System Test 6 - Exit SmartLoader Stored Memory Type 01, 04 3 3 Philips SmartLoader 99 System Version D.0 1 - Read TV CH GDE 0 2 - Write TV With Settings 3 - Write TV Without Settings 4 - Erase SmartLoader Memory POWER TV TV DCM GUEST SETUP SETUP 5 - System Test 6 - Exit SmartLoader Read? Press 0 to confirm 1 4 Philips SmartLoader 99 System Version D.0 1 - Read TV 2 - Write TV With Settings 3 - Write TV Without Settings 4 - Erase SmartLoader Memory 5 - System Test 6 - Exit SmartLoader Reading Block 23 of 63 6 EXTERNAL SPEAKER 75Ω ANT/ CABLE 5 Philips SmartLoader 99 System Version D.0 1 - Read TV 2 - Write TV With Settings 3 - Write TV Without Settings SMART PLUG 4 - Erase SmartLoader Memory 5 - System Test 6 - Exit SmartLoader Finished Reading Memory 6 PROGRAMMING A TELEVISION’S INTERNAL MEMORY WRITING TV MEMORY After the Memory has been read from one television, the Clon99-BK SmartLoader is now ready to write the memory to other televisions. This memory can be written with or without certain settings. These settings include: Picture Adjustment, Minimum and Maximum Volume, and the On Volume settings. Clon99-BK SmartLoader Box 1 EXTERNAL SPEAKER 75Ω ANT/ CABLE ON/OFF Slide Switch Typical rear jack panel of ITV SMART PLUG BEGIN Plug one end of the cable into the jack provided on the SmartLoader. Then plug the other end into the jack provided on the back of the TV. The TV jack is next to the Antenna Input terminal. Push the Slide Switch to the ON position on the SmartLoader. If the TV is currently off, it should turn on within 15 seconds. Within 20 seconds, the SmartLoader on-screen display should appear on the TV screen. If the display does not appear, check connections and push the Slide Switch to the ON position again. If there is still no response from the SmartLoader, replace its 9-volt battery. 2 3 PHILIPS SMARTLOADER 99 Copyright PCEC 1999 System Version D.0 PN 3135 019 01681 PRESS POWER TO BEGIN LED Philips SmartLoader 99 System Version D.0 1 - Read TV 2 - Write TV With Settings 3 - Write TV Without Settings 4 - Erase SmartLoader Memory RECALL SLEEP 5 - System Test 6 - Exit SmartLoader SELECT - Press the POWER button on the remote to display the Clon99-BK SmartLoader Setup Menu. Stored Memory Type 01, 04 + M Philips SmartLoader 99 System Version D.0 A/CH VOL CH 1 - Read TV MUTE 2 - Write TV With Settings 3 - Write TV Without Settings With the Setup Menu visible, press the Number 2 button on the Remote Control to select the 2nd option “Write TV With Settings” or press the Number 3 button to select the third option “Write TV Without Settings.” The screen will ask “Write?” Press the 0 button on the remote to confirm and begin the procedure. A B C D E F G 4 - Erase SmartLoader Memory 5 5 - System Test 6 - Exit SmartLoader Write? Press 0 to confirm RESET 1 2 3 4 5 6 7 8 9 7 CC CH GDE Philips SmartLoader 99 System Version D.0 1 - Read TV 0 2 - Write TV With Settings 3 - Write TV Without Settings POWER The screen will indicate “Writing Block 24 of 63” while the Clon99-BK SmartLoader is downloading the data. TV TV DCM GUEST SETUP SETUP 4 The display will then read “Finished Writing Memory” when the procedure has been completed. 4 - Erase SmartLoader Memory 5 - System Test 6 6 - Exit SmartLoader Writing Block 23 of 63 8 Philips SmartLoader 99 System Version D.0 1 - Read TV 2 - Write TV With Settings 3 - Write TV Without Settings 4 - Erase SmartLoader Memory 5 - System Test 6 - Exit SmartLoader Finished Writing Memory 7 RUNNING A SYSTEM TEST SYSTEM TEST A System Test of the Clon99-BK SmartLoader can be preformed by following the steps below. PHILIPS SMARTLOADER 99 Copyright PCEC 1999 System Version D.0 PN 3135 019 01681 BEGIN RECALL SLEEP With the Clon99-BK SmartLoader on-screen display showing, press the POWER button on the remote control SELECT - PRESS POWER TO BEGIN + M 4 The Setup Menu will appear. Press the Number 5 button on the Remote Control to select the 5th option “System Test.” Philips SmartLoader 99 System Version D.0 A/CH VOL CH 1 - Read TV MUTE The screen will ask “Test?” Press the 0 button on the remote to confirm and begin the procedure. 5 3 - Write TV Without Settings 4 A RESET As the System Test proceeds, the display will prompt the user to press the Number 1 button or the A/CH button to continue or skip to the next part of the test. 2 - Write TV With Settings B C D E F G 1 2 3 4 5 6 7 8 9 4 - Erase SmartLoader Memory 5 - System Test 6 - Exit SmartLoader 2 Stored Memory Type 01, 04 CC CH GDE Philips SmartLoader 99 System Version D.0 1 - Read TV 0 2 - Write TV With Settings 3 - Write TV Without Settings POWER When the display shows “Test Finished,” press the Number 1 button to return to the Clon99-BK SmartLoader Setup Menu. TV TV DCM GUEST SETUP SETUP 4 - Erase SmartLoader Memory 5 - System Test 3 6 - Exit SmartLoader Test? Press 0 to confirm 1 * * * * * * * * * * * Display Registration * * 12 Rows by 32 Columns * * * * * * * 0123456789012345678901 * * * * * Press 1 to Continue * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * IR Test Press A/CH to Continue Press 1 to Skip Character Set Display !"#$%&'()*+,-./01234 56789:;<=>?@ABCDEF GHIJKLMNOPQRSTUV WXYZ abcdefghijklmno Press 1 to Continue IR Test A/CH detected, IR good Press 1 to Continue 8 * * * * * * * * * * * * * * * * * * SmartLoader 99 System Test Press 1 to Continue * * * * * * * * * * * Check +12V Power Supply 12V Detected * * * * * * Press 1 to Continue * * * * * * * * * * * * * * * * * * * * * * * * * * * * Test Finished Press 1 to Continue EXITING THE CLON99-BK SMARTLOADER MENU EXIT SMARTLOADER When you have completed all the procedures you wish to preform, exiting the Clon99-BK SmartLoader and shutting down is simple. BEGIN 1 With the Clon99-BK SmartLoader on-screen display showing, press the POWER button on the remote control PHILIPS SMARTLOADER 99 Copyright PCEC 1999 System Version D.0 PN 3135 019 01681 The Setup Menu will appear. Press the Number 6 button on the Remote Control to select the 6th option “Exit SmartLoader.” RECALL SLEEP The screen will ask “Exit?” Press the 0 button on the remote to confirm and begin the procedure. PRESS POWER TO BEGIN SELECT - + M 2 A/CH VOL CH 1 - Read TV 2 - Write TV With Settings MUTE The Clon99-BK SmartLoader will display a screen that reads “Power Down Mode” then shut itself off. Philips SmartLoader 99 System Version D.0 3 - Write TV Without Settings 4 - Erase SmartLoader Memory A B C D E F G 1 2 3 4 5 6 7 8 9 5 - System Test 6 - Exit SmartLoader RESET When finished, unplug the Clon99-BK SmartLoader from the rear jack panel of the television. 2 Stored Memory Type 01, 04 3 CC Philips SmartLoader 99 System Version D.0 1 - Read TV CH GDE 0 2 - Write TV With Settings 3 - Write TV Without Settings 4 - Erase SmartLoader Memory POWER TV TV DCM GUEST SETUP SETUP 5 - System Test 6 - Exit SmartLoader 3 Exit? Press 0 to confirm 1 4 5 Power Down Mode EXTERNAL SPEAKER 75Ω ANT/ CABLE SMART PLUG 9 PROGRAMMING A TELEVISION WITH THE ON-SET KEYBOARD WRITING TV MEMORY WITH THE ON-SET KEYBOARD After the Memory has been read from one television, the Clon99-BK SmartLoader is now ready to write the memory to other televisions. The following steps show how to download or “write” memory from one television to another using the On-Set Keyboard. BEGIN Clon99-BK SmartLoader Box 1 EXTERNAL SPEAKER 75Ω ANT/ CABLE ON/OFF Slide Switch SMART PLUG Plug one end of the cable into the jack provided on the SmartLoader. Then plug the other end into the jack provided on the back of the TV. The TV jack is next to the Antenna Input terminal. Push the Slide Switch to the ON position on the SmartLoader. If the TV is currently off, it should turn on within 15 seconds. Typical rear jack panel of ITV PHILIPS SMARTLOADER 99 3 Copyright PCEC 1999 System Version D.0 PN 3135 019 01681 PRESS POWER TO BEGIN LED Within 20 seconds, the SmartLoader on-screen display should appear on the TV screen. If the display does not appear, check connections and push the Slide Switch to the ON position again. If there is still no response from the SmartLoader, replace its 9-volt battery. 2 Philips SmartLoader 99 System Version D.0 Press CH/UP to Write TV STEREO 6 Press Power to Exit System Stored Memory Type 01, 04 Philips SmartLoader 99 System Version D.0 Press the POWER button on the front of the TV to display the Clon99-BK SmartLoader “Write TV” Menu. Press CH/UP to Confirm Write INSTALL / MENU – VOLUME + CHANNEL Press CH/DN to Abort POWER Press Power to Exit System Stored Memeory Type 01, 04 Press the CH/UP button on the front of the TV to write the memory to the television. The screen will ask “Press CH/UP to Confirm Write,” “Press the CH/DN to Abort,” or “Press the Power to Exit System.” Press the CH/UP button to confirm and begin the procedure. MENU Philips SmartLoader 99 System Version D.0 – VOLUME + CHANNEL POWER Press CH/UP to Confirm Write Press CH/DN to Abort Press Power to Exit System 4 The screen will indicate “Writing Block XX of XX” while the Clon99BK SmartLoader is downloading the data. 8 Writing Block 23 of 63 6 5 Philips SmartLoader 99 System Version D.0 Press CH/UP to Confirm Write Press CH/DN to Abort The display will then read “Finished Writing Memory” when the procedure has been completed. Press Power to Exit System Finished Writing Memory Press the Power button on the front of the TV to EXIT the system. 10 CLON99-BK SMARTLOADER DISPLAYS USING PROGRAMMING TRANSMITTER FOR NON-GLOBAL TV Follow these screens when choosing option “0” - EXIT. PHILIPS SMART LOADER TELEVISION TYPE - SAVED DATA TYPE - - EXIT SMART LOADER SYSTEM ?? ARE YOU SURE?? SYSTEM REVISION D.0 PN 3135 019 01681 PRESS POWER TO BEGIN 0 2 3 4 5 - EXIT 1- READ TV WRITE TV - PIC WRITE TV - NO PIC ERASE TV/BUS SYSTEM TEST 1 - EXIT SMART LOADER 0 - RETURN TO MENU Follow these screens when choosing option “1” - READ TV. PHILIPS SMART LOADER TELEVISION TYPE - SAVED DATA TYPE - - TELEVISION TYPE - - TELEVISION TYPE - ?? ARE YOU SURE ?? SYSTEM REVISION D.0 PN 3135 019 01681 PRESS POWER TO BEGIN 0 2 3 4 5 - EXIT 1- READ TV WRITE TV - PIC WRITE TV - NO PIC ERASE TV/BUS SYSTEM TEST 1 - READ TV MEMORY 0 - RETURN TO MENU 1 - READ TV MEMORY 0 - RETURN TO MENU READING BLOCK - - TV MEMORY READ AND SAVED Follow these screens when choosing option “2” or “3” - WRITE TV - PIC, or WRITE TV - NO PIC. PHILIPS SMART LOADER SYSTEM REVISION D.0 PN 3135 019 01681 PRESS POWER TO BEGIN TELEVISION TYPE - SAVED DATA TYPE - 0 2 3 4 5 - EXIT 1- READ TV WRITE TV - PIC WRITE TV - NO PIC ERASE TV/BUS SYSTEM TEST TELEVISION TYPE - - TELEVISION TYPE - - SAVED DATA TYPE - - SAVED DATE TYPE - - ?? ARE YOU SURE ?? 1 - WRITE TV MEMORY 0 - RETURN TO MENU 1 - WRITE TV MEMORY 0 - RETURN TO MENU WRITING BLOCK - - MEMORY WRITE COMPLETE Follow these screens when choosing option “4” - ERASE. PHILIPS SMART LOADER TELEVISION TYPE - SAVED DATA TYPE - - SAVED DATA TYPE - - SAVED DATA TYPE - ?? ARE YOU SURE ?? SYSTEM REVISION D.0 PN 3135 019 01681 PRESS POWER TO BEGIN 0 2 3 4 5 - EXIT 1- READ TV WRITE TV - PIC WRITE TV - NO PIC ERASE TV/BUS SYSTEM TEST 1 - EARSE MEMORY DATA 0 - RETURN TO MENU 1 - ERASE MEMORY DATA 0 - RETURN TO MENU DATA ERASURE COMPLETE Follow these screens when choosing option “5” - TV/BUS SYSTEM TEST. PHILIPS SMART LOADER SYSTEM REVISION D.0 PN 3135 019 01681 PRESS POWER TO BEGIN TEST DATA TERMINAL POWER TELEVISION TYPE - SAVED DATA TYPE - 0 2 3 4 5 - EXIT 1- READ TV WRITE TV - PIC WRITE TV - NO PIC ERASE TV/BUS SYSTEM TEST TV/DATA TERMINAL *DISPLAY REGISITRATION* SYSTEM TEST SEQUENCE * * 1 - CONTINUE TEST * 0 - RETURN TO MENU * * * * * 10 LINES/26 CHARACTERS * 1 - CONTINUE TEST 0 - RETURN TO MENU NO INTERNAL TELEVISION ERRORS DETECTED NO POWER SUPPLY DETECTED 1 - CONTINUE TEST 0 - RETURN TO MENU 1 - TEST COMPLETE 11 DOWNLOAD CHARATER SET IR DATA LINK TEST !"#$%^'[]*+,-./0123 456789;^<=>?/ABCDEFG HIJKLMNOPQRSTUVWXYZ PRESS A/CH ON TRANSMITTER 1 - CONTINUE TEST 0 - RETURN TO MENU 1 - CONTINUE TEST 0 - RETURN TO MENU CLON99-BK SMARTLOADER DISPLAYS USING ON-SET KEYBOARD WITH NON-GLOBAL TV PHILIPS SMART LOADER SYSTEM REVISION D.0 PN 3135 019 01681 PRESS POWER TO BEGIN TELEVISION TYPE - SAVED DATA TYPE - POWER TELEVISION TYPE - SAVED DATA TYPE - CH/UP CH/UP - WRITE TV MEMORY ?? ARE YOU SURE ?? CH/UP - WRITE TV MEMORY CH/DN - DO NOT WRITE CH/UP WRITING BLOCK - - MEMORY WRITE COMPLETE CH/DN NO DATA SAVED FOR TELEVISION TYPE - TV PRODUCT TYPE - - INDEX Battery Installation - Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Battery Installation - Clon99-BK SmartLoader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Erase Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Exiting the Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 On-Set TV Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10, 12 On-Screen Displays for Non-Global TV with Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 On-Screen Displays for Non-Global TV with On-Set Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Programming with On-Set Keyboard for Global TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Programming (Writing) Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Read Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3, 5-9 Safety/Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 System Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 12