Download Craftsman 358.351560 Operator`s manual
Transcript
Operator's Manual CRRFTSMRN 2.2 cu. in./36cc 2-Cycle GASOLINE CHAIN SAW Model No. 358.351560 - 16in. Bar @ Read and follow all Safety Rules and Operating WARNING: Instructions before first use of this product. For to your questions thispm, product: Call answers 7 am--7 pm, Mon.-Sat., or about 10 arn--7 Sun. • 1-800-235-5878 (.o..,=_=_._m.) I 'S_s, Roebuck and Co., Hoffman Estates, IL 60179 USA 530087619 06/08/98 !saW_e_n_/ules :_mb) )Operation Maintenance Service and Adjustments Storage ShootingChart Trouble 11 14 Pads List Spanish , Pads & Ordering 16 17 20 24 Back FULL ONE YEAR WARRANTY ON CRAFTSMAN ® GAS CHAIN SAW For one year from the date of purchase, when this Craftsman Gas Chain Saw is maintained, lubdcated and tuned up according to the owner's manual, Sears will repair, free of charge, any defect in matedai or wodornanship. This warranty excludes the bar, chain, spark plug and air filter,which are expendable parts, and become wom dudng normalusa. If this Gas Chain Saw is used for commercial or rental purposes, this warranty applies for 30 days from the date of purchase. WARRANTY SERVICE IS AVAILABLEBY RETURNING THIS CHAIN SAW TO THE NEAREST SEARS SERVICE CENTER IN THE UNITED STATES. This warranty gives you specific legal dghts,and you may also have other dghts which vary from state to state. Sears, Roebuck and Co., D/817 WA, Hoffman Estet_'s,:lL 60179 WARNING: Always disconnect spark plug wire when making repairs except for carburetor adjustments. Because a chain saw is a high-speed woodcutting tool, careless or improper use of this tool can cause sedous injury. PLAN AHEAD • Reetdct the use of your saw to adult users who understand and can follow the safety rules, precautions, and op-erating Instructionsfound in this manual. Snug Firing _ Clothing Heavy Duty Gloves Safety Shoes j \ • • • Chaps NM • ,_Wear protective gear. Always use steef-toed safety f_twear with nonslip soles; snug-fittingclothing;heavy2 duty, non-slipgloves; eye protection such as non-fogging,vented goggles or face screen; an approved safety hard hat; and sound barriers (ear plugs or mufflers)to protect your hsadng. Regular users should have headng checked regularlyas chain saw noise can damage hearing. Secure hair above shoulder length. Keep aimparts of your body away from the chainwhen the engine is running. Keep chgdrsn,bystanders, and animals at least 30 feet (10 meters) away from the work area when starting and usingthe saw. Do not handle or operate a chain saw when you are fatigued, ill, or upset, or if you have taken alcohol, drugs, or medication. You must be in good physicalconditionand mentally alert. If you have any conditionthat might be aggra.vatedby strenuous work, check with doctorbefore operating. Do not stert cuttinguntilyou have a clear work area, secure footing, and especially if you are felling a tree, a retreat path. OPERATE YOUR SAW SAFELY • Donot operatewithonehand Seriousinjurytothe operator,helpers,or bystandersmayresultfromonehandedoperation.A chainsaw is intendedfortwo-h.anded use. • Operate the ch_unsaQwonly-ine,wellventilated outdoor area. • Do not operate saw from a ladder or in a tree, unless you are specifically trained to do co. • Make sure the chain will not make contact with any object whge starting the engine NeverW to startthe saw whenthe guidebar is in a cut. • Store the unit and fuel in a cool, dry well ventilatedspace where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches,furnaces, etc. GUARD AGAINST KICKBACK Follow all safety rules to help.avoid kickback and otherforces which can result in ssdous injury. k Path Avoid Obstructions • Do not put pressure on the saw, espeoiailyat the end of the cut. Doing so can cause you to lose control when the cut is completed. • Stop engine before seffing saw down. • Hand carry saw only when engine is stopped. Carry with muffler away from Qear The WoddngArea body;,guide bar & chain projectingbeWARNING: Rotational Kickback can hind you; guide bar preferably covered with a scabbard. occur when the moving chain contacts an object at the upper portion of the tip MAINTAIN YOUR SAW IN GOOD WORKING ORDER • Have all chain saw service performed by a qualified service dealer except the items listed in the maintenance section of this manual. • Make certain the saw chain stops movingwhen the throttle trigger is released. For correction, refer to "CarburetorAdjustments." • Keep the handles dry, Clean, and free from oil or fuel mixture. • Keep caps and fasteners securely tightened. • Use only Craftsman accassodes and replacement parts as recommended. Ne'ger modifyyour saw. ofthe guidebar.Contactat the upper portion of th6'tip of the guide bar can cause the cl'_ainto dig into the object, which stops the chainfor an instant.The resultis a lightningfast, reverse reaction which kicks the guide bar up and back toward the operator. Pinch-K]ckhackand Pull-In occur when the chain is suddenly stopped by being pinched, caught, or by contacting a foreign object in the wood. This sudden stopping of the chain results in a reversal of the chain force used to cut wood and causes the saw to move in the opposite direction of the chain rotation. Pinch-Kickback drivesthe saw straight back toward the operator. Pull-In pulls the saw away from the operator. HANDLE FUEL WITH CAUTION REDUCE THE CHANCE OF • Do not smoke while handling fuel or KICKBACK while operatingthe saw. R_ that kickbackcan happen. • Eliminatsallsourcssof sparksor ltame • With a basic unden_mding 1ofkiddoeck, in arees where fusl is mixed or psured. you can reducethe element of surprise • Mix and pourfuel in an outdoor area which conlrbutesto eccidents. and use an approved, marked con• Never let the moving chain contact tainer for all fuel purposes. Wipe up any object at the tip of the guide bar. all fuel spills before starting saw. • Keep working area free from oi0struc• Move at least 10 feet (3 meters) from tions such as other trees, branches, fueling site before starting. rocks, fences, stump, et_. Eliminate • Turn the engine off and let saw cool in or avoid any obstructionthat your saw ' a-nt)rPcombustiblearea, not on dry chain could hit while cutting. leaves, straw, paper, etc. Slowly re• Keep saw chain sharp and propedy tensioned. A loose or dull chain can move fuel cap and refuel unit. increase the chance of kickback. Follow manufacturer's chain sherpenlng and maintenance instructions.Check tension at regular intervals, but never with engine running. Make sure bar clamp nuts are securely tightened. • Begin and continue cuttin_lat full speed. If the chain _movmg at a slower speed, there _sgreeter chance of kickback occurring. • Use extreme caution when reentering a cuL • Do not attempt cuts startingwith the tip of the bar(plunge cuts). • Watch for shifting logs or oti_erforces that could dose a cut and pinch orfall into chain. • Use the specified Reduced-Kiokback Guide Bar and Low-KiokbackChain. Avoid Pinch-Kickback: • Be extremely swam of situations or obstructions that can cause matedal to pincl_,the top of or otherwise stop the chron. • Do not cut more than one log at e time. • Do not twist saw as bar is withdrawn from an undercut when bucking. Avoid PulHn: • Always begin cutting with the engine at full speed and the saw housing against wood. • Use wedges made of plastic or wood. Never usa metal to hold the cut open. MAINTAIN CONTROL Stand to the left of the saw keep your body from being in a direct line with'the cuffing chain. • Stand with,your walght evenly balanced on both feet. • Do not overreach. You could be drawn or thrown off balance and lose control. • Do not cut above shoulder height. It Is difficultto maintain control of saw 'above shoulder height. KICKBACK SAFETY FEATURES WARNING: The followingfeatures are included on your saw to help reduce hazard of kickback;however, such features will not totally eliminate this danger. Do not rely only on safety devices. • Handguard: designed to reduce the chance of your left hand contacting the chain ifyour hand slips off the front handlebar. • Positionof front and rear handlebars: designed _ distance between handles and ",n-line"with each other.The spread and."in-line" position of the hands prodded by this design work together to give balance and rasmtance in controlling the pivot of the saw back toward the operator if kickback occum. • Reduced-I_ckback Guide Bar:.designed with a small radius tip which reduces the size of the kickback dan_er zone. This type b.m has been emonstrated to significantlyreduce the number and sedousness of kickbacks when tested in accordance with ANSI B175.1. Small Radius Tip Guide Bar underside of handlebar Thumbon I i Elbow locked • Low-KickbackChain: has met kickback performance r_jui_ when tested on a represent_ve sample of chain Neverreverse han@podtJons saws below 3.8 cubic inch • A good, firm grip on the saw with both displacementspecifiedin ANSI B175.1. hands will help ,you maintain control. Low-_ckbackChain Don't let go. Gdp the rear handle with Contoured Depth Gauge your dght hand whether you are dght or left handed. Wrap the tingem of Deflects your left hand over and around the Force And Allows front handlebar, and your left thumb _ Wood longsted To Grsdu_ Guard Link under the fiord handlebar. Keep your Ride Into Cutter left arm straight with the elbow locked. SAFETY NOTICE: Exposure to. • Positionyour !eft hand on the front handlebar so it is in a straight line with _"mations through prolonged use of your dght hand on the rear handle gasoline powared hand tools could when making bucking cuts. Stand cause blood vessel or nerve damage in the fingers, hands, and joints of people slightlyto the left side of the saw to \ 4 prone to circulation disorders or abnormalswelling. Prolonged use in cold weather has been linked to blood vessel damage in otherwise healthy people. If symptoms occur such as numbness,10am,lossof strpng__,_ change in.sldncolor o'ttextu-re,or_ of fee._. m the fingers, hands,'or joints, discontinuethe use of th=stool and seek medical attention. An anti-vibrationsystem does not guarantee the avoidance of these problems.Users who operate power tools on a continual and regular baszs must closely monitor their physical. cond_on and the condrdion of thzstooL CHAIN BRAKE If this saw is to be used for commercial logging, you must order and installa chain brake to comply with Federal OSHA Regulations for CommerciaiLogging. Contact your Sears Service Center or call 1-800-235-5878. SPARK ARRESTOR: Your saw is equipped with a tempomtum limiting CARTON CONTENTS Check cation contents against the followinglist. Model 358.351560 • Chain Saw (fully assembled) • Bar tool • 2-cycle engine oil • Examineparis for damage. Do not use damaged parts. n_.er and spark arre_ s_rsan which meets the re remante of California Codes 4442 and 4443. All U.S. forest land and the slates of Califomia, Idaho, Maine, Minnesota, New Jersey, Oregon, and Washington require by law that many internal combustion engines be equipped with a spark arrestor screen. If you operate a chainsaw in a stateor localeW,hem n_oonr_llationse.xi_,youare legally • for m=,nteining the operating condition of these pads. Failure to do so is a viola_on of the law. Refer to Customer Responsibilities chart in the MAINTENANCEsection. STANDARDS." This chain saw is listed by UndenmitersLaboratories, Inc. in accordance with American National Standards for Gasoline-Powered Chain Saws Safety Requirements (ANSI B175.11-t_1991). • If you need assistance or find that parts are missing or damaged, please call 1-800-235-5878. NOTE: It is normal to hear the fuel filter . rattle in an empty fuel tank. Your unit has been factory tested and the carburetorprecisely a_usted. As a resultyou may smell gasoSne orflnd a drop of oil/fuel residue on the muffler when you unpackthe unit. ASSEMBLY Your saw is fully assembled; no assamUy le KNOW YOUR SAW READ THIS OPERATOR'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR CHAIN SAW. Compare the illustrationswith your unit to familiadze yourseff withthe _ocation of_thevadous controlsand adjustments. Save this manual for future reference. ' Bar Tool Front Handle Starter Rope OWSTOP CRRFT3MRN" Bar Oil RII Cap Housing Fuel Mix RII Cap Cylinder Cover Fast Idle Lockout Adjus_ng Screw Rear Handle Throttle Tdgger Ct_n Direction of Travel Choke Knob BarClarnp Chain Bar Clamp Nuts GuideBar Catcher ON/STOP SWITCH The ON/STOP Switch is used to stop the engine. THROTTLE TRIGGER The throttletdgger controlsengine speed. THROTTLE LOCKOUT The throttle lockout must be pressed before you can squeeze the throttletrigger. This feature prevents you from accidentallysqueezing the tdgger. F_ IDLE LOCK The fast idle lock holds the throttle tdgger in the starting position.Activate the fast idle lock by pressing the throttle lockout and squeezing the throttle tfig_e_. With the throttle rigger squeezed, press the fast idle lock. Release the thmffie lockoutand tdgger while holding the fast idle lockbutton. CHOKE KNOB The Choke Knob activates the choke to provideadditionalfuel to the engine duringcold starting. PRIMER BULB The Pdmer Bulb circulates fuel to the carburetor to provide quicker starting. CHAIN TENSION It is normal for a new chain to stretch dudng first 30 minutes of operation. You should check your chain tension frequent. See Chain Tension under the enaca and Adjustments section. 6 BEFORE STARTING ENGINE WARNING: Be sure to read the fuel handling informationin the safety rules section of this manuel before you begin. If you do not understand the fuel hendling informationdo net attempttofuel your unit. Seek help from someone that does understand the informationor cell the customerassistance help line at 1-800-235-5878. GUIDE BAR AND CHAIN OIL The chain oiler provides continuous lubricationto the chain and guide bar. Be sure to fill the bar o01.tankwhen you fill the fuel tank (Capacity = 6.8 ft. oz.). For maximum guide bar and chain life, we recommend you use Craftsman chain saw bar oil. If Craftsmen bar oil is not available, you may use a good grade SAE 30 oil untilyou are able to obtainCraftsmen brand. The oil output is automatically metered during operation. Your saw will use approximately one tank of bar oil for every tank of fuel mix.Always fill the bar oil tank when you flil the fuel tank. FUELING ENGINE This engine is certifiedto operate on unleaded gasoline. Before operation, gasoline must be mixed with a good quality2-cycle air-ccoled ehgine oil. We recommend Craftsman brand o,1.Mix gasoline and oil at a ratio of 40:1 (A 4_.1 ratio is ob_nsd by mixing 3_. ounces of oil with 1 gallon of unleaded gasoline). DO NOTUSE automotive oil or boat oil. These oilswill cause engine damage. When mbdngfuel follow the instructions pdntedonthe container. Once.oilisaddedto the gasoline, shake container momentarily to assure that the fuel is thorougldymlxed. Always read and follow the safetyrules relatingto fuel before fueling your unit. IMPORTANT ExpedenceindicaWs that elcohoiblanded (ce,edgasoh¢ or or mathenoi)cen atirad moielurewhich linesand catouratorare emply. Use fresh fuel nsxt ssason. See STORAGEk_'tructions for edd_x_ informa_on. Never use engine or carburetor deener products in the fuel tank or permanent damage may occur. See the STORAGEsection for additional information. STOPPING YOUR ENGINE • MoveOn/Stopswitchto STOP. • If enginedoes notstop,pullchoke knoboutfully. STARTING YOUR ENGINE COLD ENGINE OR WARM ENGINE AFTER RUNNING OUT OF FUEL • Fuel engine with 40:.1 fuel mix. • Fillbar oil tenk with bar oil. • Prime engine by pressing primer bulb six times. • Move On/Stop switch to ON. Primer Bulb t • • Full • Acluate choke by pulling choke knob fully ouL • Set saw on the ground. Grip front handle with your left hand and place rightfoot through mar handle. Starter Rope Handle LeJtHand on Front Handle RearHandle • Set fast idle by depressing the throUle lock with your right hand. Then, adds duringstorage.Addio gas can squeeze end holdthrottie trigger. With whdd_,_e the fuel systemof an engine your thumb, press the fast idle lock storage. , down and hold. Next, release the To _Q_-engine problems,the fuel systhrottie _gger. tem should be emplbd before storagefor • .DONOT squeeze throttie trigger dur30 claysor longer.Dlain the gas tank, ing starling; othelwise, it will be necstaxtthe engine and let it run unffithe fuel essary to msot the fast Idle iock. lesdsto eepar_on and_ of NOTE: When pullingthe starter rope, OPERATING do not use the full extent of the rope. Do not let stinter rope snap bad_ Hold handle. Let rope rewind slowly. • Check chain tendon before first use and aftor,1 minute of operation. See Chain Tension in the Maintenance 8eotJon. TIPS • Pull miter rope handle firmly and quicklywith your righthand untl"lthe • Cut woed only.Do not out metsl, plasengine attempts to start or 5 pulls. tics, masonry,non-wood buildingrnaThen push tl_ chokeknob fully in. tedab, etc; • Stop the saw ifthe chatn atnlcse a forResume pullinghandle until engi0e starts. See Igustration. eign object.Inspectthe saw and re• Above 40°F, allow engine to runfor pair paits as .r.r._.: • Keep the chain out of dirt and sand. approximately 5 seconds. Push the Even a small amount of dirtwillquick. choke knob in to the OFF position; then squeeze and release throttle trig. blY dulia chainandincreasetheposslllHyof idcid:)ask. ger to allow engineto idte. • Practice cuttinga few small logsusing • Below 40°F, allow engine to warm up the foflowingsteps. This wil helpyou for 30 saconds to 1 mirnJte.Push get the "feet"of using your saw before choke knob in 1/2 way;,then squeeze you begin a majorsawing operaSon. and release throffie tdgger to allow • Squeeze the throttle _gger and alengine to idle. • To stop engine, move On/Stop switch to the STOP position. STARTING A WARM ENGINE DO NOT use the choke to start a warm lowthe engineto reach full speed beforecutting. • Begincuttingwiththe saw frame againstthe log • Keep the engine at full speed the enbretime you are cutting. • AJIowthe chain to cut for you. Exert only lightdownward pressure. • Release the throttle tdgger as soon as the cutis completed, allowingthe engineto idle. If you run the saw at full throttle without a cuffing load, unnecessarywear can occur. • To avoidlosingcontrol when cut is complete, do not put pressure on saw at end of cut. • Stop enginebefore setting saw down. engine or floodingand hard starting may occur. • Move On/Stop switchto ON. • Set fast idle lock. • Be sure choke is in the OFF position. • With saw on ground,gdp front handle with left hand and place your dght foot through rear handle. • Pull starter rope handle until engine starts. • Squeeze and release throttle trigger to return engine to idlespeed. TREE FELUNG TECHNIQUES WARNING: Check for broken or dead DIFFICULT STARTING OR branches whichcan fall while cutting STARTING A FLOODED ENGINE The engine may be flooded if it has not ca_ing serious .injury.DO not cut near buddingeorelectrical wires if you do not started after 10 pulls.Flooded engines know the directionof tree fall, norcut at ;can be cleared of excess fuel with the night since you will not be able to see following procedure: well, nor dudngbad weather suchas • Engage the fast idl_ lock. • Verify that the On/Stop switch ls in the rain, snow,or strongwinds, etc. ON position. • Carefully plan your sawing operation in advance. Push choke knob to the OFF position. •"With saw on ground,gnp front handle • Clear the workarea. You need a dear with left hand and place dght foot area allaround the tree so you can through rear handle. have secure footing. • Study the naturalconditions thatcan • Pull starter rope handle until engine starts. _usa the tree to fall in a partbular direction.These conditions include: • Starting could require many pulls de• The wind directionand speed. pending on how badly the unit is • The lean of the tree. The lean of a _ flooded, if en_ne still fails to start, re-fer to the TROUBLESHOOTING chart or tree mightnot be apparent due to call 1-800-235-5878. uneven or sloping terrain. Use a 8 plumbor levelto determinethe directionoftree lean. • Weightendbrancheson oneside. • Surroundingtrees end obstacles. • Look for decay and roL If the trunk is rotted, itcan snap end fall toward the operator. * • Make sure there is enough room for the tree to fall. Maintain a distance of 2-1/2 tree lengths from the nearest person or other objects. Engine noise can drown out a warning call. • Remove dirt, stones, loose bark, nails, staples, end wire from the tree where cuts are to be made. This hinge will help prevent the tree from in the wrong direction. HingeholdsYeson stumpandhelps controlfall NOTE: Before falling cut is complete, use wedges to open the cut wben neceesaw to controlthe direction of fall. To avoid klcld)ack end _n damage, use wood or plastic wedges, but never steel or iron wedges. Plana dear retreatpath • Be alert to signsthat the tree is ready to fall: crackingsounds, widening of the fellingcut, or movement in the upper branches. • As tree startsto fall, st.op saw, put it down, and get away quickly on your planned retreat path. FELUNG' LARGE TREES • Be extremely cautious with partially fallen trees that may be poorly sup(6 inches in diameter or larger) ported. When a tree doesn't fall cornThe notch method is used to fell large pletely,seLthe saw aside and pull trees. A notch is cut on the side of the down the tree _vith a cable winch, tree in the desired directionof fall. After block and tackle, or tractor. Do not a felling cut is made on the opposite use your saw to cut down a partially side of tree, the tree will tend to fall in fallen tree. the directionof the notch. CUTTING A FALLEN TREE NOTE: If tree has large buttress roots, remove them before rnaldng the notch. (BUCKING) Bucking is the term used for cuttinga NOTCH CUT AND FELUNG TREE fallen tree to the desired log s'rTe. • Make notch cut by cuffingthe top of WARNING: Do not stand on the log the notch first. CUt through 1/3 of the being cut. Any porlJoncan rollcausing diameter of the tree. Next complete loss of footingend control. Do not stand the notch by cuttingthe bottom. See illustration.Once the notch is cut, re- downhill of the log being cut. move the wedge of wood from tree. IMPORTANT POINTS RnaJcuthere • Cut only one logat a time. Rrstcut • Cut shatteredwood very carefully;, sharp pieces of wood could be flung toward operator. • Use a sawhorse to cut small logs. Notch _ Never allow another person to hold the log while cuffingend never hold the logwith your leg or fooL • Do notcut in enaree where logs, =r on of & . • After removing the wood, make the fellingcut on the opposite side of the notch.Thisisdoneby makinga cut abg_-two inches higher than the center of the notch. This will leave enough uncut wood between the felling cut and the notch to form a hinge. ,mb endroo m tanCecL Drog intoa deer en)a before cultJngthem. BUCKING TECHNIQUES WARNING: If saw becomes pinched or hung in a log, don'ttry to force It out. You can losecontrol ofthe saw resulting in injury end/or damage to the saw. Stop the saw, drive a wedge of plastic orwood intothe cut unt_the saw can be • UMngs log rernovndeasily.Rsstartsaw and carefulty for support reenterthe cut. Do not usa a mstal wedge.Donotattampt to restart your ..... saw when it is pinchedor hung In a log. Use a wedge to mrnove pinched saw ,..,__ _.,. _ut,_, . ._ o _1_ INjt _ ._ _ _ O" la_ -£-- .4_ql:_ __ ---" "1_1' Turn.sawORFand usas pisstJc or wcoaenwedgeto forcecutogen. Overcutting begins on the top side of the log with the bottom of the saw against the log. When overcuttJnguse lightdownward pressure. Ovemuttlng Undercutting BUCKING USING A LOG OR SUPPORT STAND • Remember your first cut is always on the compression side of the log. (Refer to the illustrationbelow for your first and second cut). • Your first cut should extend 1/3 of the diameter of the log. • Finishwith your second cut. Undercutting involvescutting on the underside of the log with top of saw against the log. When undercuttinguse lightupward pressure. Hold saw firmly and maintaincontrol. The saw will tend to push back toward you. Using a support stand WARNING: Never turn saw upside down to undercut. The saw cannot be controlled in this position. Always make your first cut on the compression side of the log. Rrst cut on common _ 2ndCut 1stCut L 2_ Cut side of log 2 -P Second cut Rrst cut on compression side of log BUCKING WITHOUT A SUPPORT • Overcut through 1/3 of the diameter of the log. • Roll the log over and finish with a sacond overcut. •-Watch for logs with a compresion side. See ,lustratlon above for cutting logs with a compression side. LIMBING AND PRUNING WARNING: Never climb intoa tree to limb or prune. Do not stand on ladders, platforms,a log, or in any position which can cause you to lose your balance or control of the saw. IMPORTANT POINTS • Watch out for spfingpoles. Springpolesare small size limbs which can whip toward you, or pull you off balance. Use extreme cautmn when cuttingsmall size limbs. • Be alert for spdngback. Watch out for branches that are bent or under pressure. Avoid being struckby the branch or the saw when the tension in the wood fibers is released. • Frequentlyclear branches out of the way to avoid tdpping over them. 10 •UMBING Limba tree onlyafterit is cutdown. branchesarehigherthanyourshouldef.Geta professionalto dothe job. • Leave the larger limbs underneath the • Make your first cut 1/3 of the way felled tree to support the tree as you through the bottom of the limb. work. • Next make a second cut ell the way • Start at the base of the felled tree and through the limb. worktoward the top, _uttingbranches • Rnish the pruningoperation by using and limbs. Remove small limbswith an overcut so that the stump of the one cut. limb protrudes I to 2 inches from the trunk of the tree. • Keep the tree between you and the chain. Second cut • Remove larger, supporting branches withthe 1/3,2/3 cuttingtechniques descdbsd in the bucldng section. • Always use an overcut to cut small Rrst cut and freely hanging limbs. Undercut1/3 of way ting could cause limbsto fall and pinch the saw. PRUNING 3rd cut I to 2 in. from trunk of tree WARNING: Limit pruningto limbs shoulder height or below. Do not cut it CUSTOMER RESPONSIBILITIES Fill in dates as you complete regular service Before After Ever_ Every Yearly Service Dates Use Use 5 hrS. 25 hrs Check for damaged/wom parts p,, Check for loose fasteners/parts _, Check chain tension 11 Check chain sharpness p- Check guide bar p,, Clean unit & labels p,, Clean air filter _' ClaaNiuspect spark arrestor sqr_rL& inspect muffler _" Replace spark plug GENERAL RECOMMENDATIONS The warranty on this unit does not cover items that have been subjected to operator abuse or negligence. To recalve fullvalue from the warranty, the operator must maintain unit as instructed in this manual. Various adjustments will need to be made periodically to propady maintain your unit. • Once a year, replace the spark plug, air filter element, and checl_ guide bar • _"€:_a-'infor wear. A new spark plug and air filter element assures proper alr-fual mixture and helps your engine _' run better and last longer. WARNING: Disconnect the spark plug before performing maintenance except for carburetor adjustments. LUBRICATION 1 Bar Sn,_L._, -'_---, 2 Bar Oil R"Ca0 'j_ 1 Usesprocketlubd_tion =" "_ 2 Use Craftsman chain saw bar oil 44 CHECK FOR DAMAGED OR WORN PARTS Replacement of damaged_om parts should be referred to your _ears _ervice Center. NOTE: It is normal for a small amount of oil to appear under the saw after engine stops. Do ndt confusethis with a laaidng oiltank. • On/Stop Switch- Ensure On/Stop switch functionsproperly_by moving the switch to the "Stop position. Make sure engine stops; then restart engine and continue. • Fuel Tank- Do not use saw if fuel tank shows signs of damage, or leaks. • Oil Tank- Do not use saw if oiltank shows signs of damage or leaks. CHECK FOR LOOSE FASTENERS AND PARTS • Bar Clamp Nut • Chain • Muffler • Cylinder Shield • Air Filter • Clutch Drum/Sprocket • Handle Screws • Vibration Mounts • Starter Housing • Handguard CHECK CHAIN TENSION • Use the screwdriver end of the bar tool to move chain around guide bar to ensure kinks do not exist. The chain should rotate freely. • bettool around har to ensure_ links ere In bet groove. • Liftup tip Qfguide bar to check for sag. Release tip of guide bar, then turn adjustingscrew until sag does not e_st. • While liftingtip of.guide bar, tighten ,bar damp.nuts with the bar tool. Torqueto 10-15 ft-lhs. • Usa the screwdriver end of the bar tool to move chain around guide bar. • If chaindoes not rotate, it is too tight. Slightlyloosen bar clamp nuts and loosen chain by turningthe adjusting screw. Rstightan bar clamp nuts. • If chain is too loose, it wilt sag below the guide bar. DO NOT operate the saw if the chain is loose. CHECK CHAIN SHARPNESS A sharpchain makes wood chips. A dull chain mitkes a sawdust powder and cuts slowly. CHAIN SHARPENING Chain sharpening requires special tools. You can purchase sharpening tools at Sears or go to a professional chain sharpener. CHECK GUIDE BAR Concrdionswhich require guide bar maintenance: • Saw cuts to one side or at an angle. • Saw has to be forced through the cut. • Inadequate supply of oil to bar/cheln. Check the condifionof guide bar each time chain is sharpened. A worn guide bar willdamage the chain and make cuttingdifficult.To maintain guide bar. Bar ClampNuts • Move On/Stop switchto "Stop." • Remove bar and chain from saw. • Looser bar clamp nuts untilthey are • Clean all sawdust and any other finger tight againstthe bar damp. debrisfrom the guide bar groove and •Tum adjusting screw untilchain baresprocket hole after each use. _ytouches the bottom of guide bar. GuideBarGroove __ y Remove Sawdust From 12 sp=k.t, . IJ = • Add lubricantto sprocket hole after each use. • Burringof guide bar mils is a normal process of railwear. Remove these burrs with a fiat file. • When railtop is uneven, use a flat file to restore square edges _ sides. sidesSquare FileEdgesand WomGroove CorrectGroove Replace guide bar when the groove is wom, the guide bar is bent or cracked, or when excess heating or burringof the rails occurs, if replacement is necessary, use only the guide bar specified for your saw in the repair parts listor on the decal located on the chain saw. CLEAN UNIT & LABELS • Clean the unit using a damp cloth with a mild detergent. • Wipe off unit with a clean dry cloth. CLEAN AIR FILTER A dirty air filter decreases the life and performance of the engine and increases fuel consumption and harmful emissions. Always clean your air filter after 15 tanks of fuel or 5 hours of operation, whichever comes first. Clean more frequently in dusty conditions.A used air filter can never be completely cleaned. It is advisable to replace your air filter with a new one after every 50 hours of operation, or annually, whichever comes first. To clean filter:. • Loosen 3 screws on cylindercover. • Remove cylinder cover. • Remove air filter. • Clean the air filter using hot soapy water. Rinse with clean cool water. Airdry completely before reinstalling. • Lightlyoil air filter before installingto improve the efficiency of eir filter. Use 2-cycle engine oil or motor oil (SAE 30). Squeeze excess oil from filter. • Reinstall air filter. • Reinstall cylinder cover and 3 screws (15-20 in-lbs.). CylinderCover Air Filter Screws INSPECT MUFFLER AND SPARK ARRESTOR SCREEN As the unit is used, carbon deposits build up on the muffler and spark arrestor screen, and must be removed to avoid creating a fire hazard or affecting engine performance. Replace the spark arrestor screen if breaks occur. Muffler Diffuser Muffler Cover Screws Body Muffler Cover CLEANING THE SPARK ARRESTOR SCREEN Cleaning is r_qtJiredevery 25 hours of operation or anhually, whichever comes fireL • Loosen and remove the 2 muffler cover screws • Remove the muffler cover (cover snaps off muffler body). • Remove muffler diffuserand spark arrestor screen assembly.Notice the orientationof these parts for reassembling. • Clean thespark arrestor screen with a wire brush. Replace screen if breaks are found. • Replace any broken or cracked muffler parts. • Reinstall diffuserand spark arrestor screen assembly with roundholes facing up. • Reinstall muffler cover and 2 screws (7.8ft-bs). REPLACE SPARK PLUG The spark plug should be replaced each year to ensure the engine starts eesBr and runs better. Ignitiontiming is fixed and nonadjustable. • Loosen 3 screws on cylinder cover. • Remove the cylinder cover. Pull off the spark plug beoL. • Remove spark plug from cyl,nderand discard. • ReplacewithChampionRCJ7Yspark plugandtightenwitha 3/4inchsocket wrench(10-12ft-lbs).Sparkpluggap shouldbe .025in. Cylinder Cover • Reinstall the spark plug boot. • Reinstall the cylindercover and 3 screws (15-20 in-lbs). Spark Rug CHAIN REPLACEMENT • Slide the guide bar rearward until it stops againstthe sprocket. CAUTION: Wear protective gloves • Carefully remove new chain from when handling chain. The chain is package. Hold cha,n with the drive sharp and can cut you even when it is linksas shown. not moving. Culters Dep_ Gauge It is normal for a new chalnto strstchduring • e flint "15minutes of operation.You shouldrecheckyourchaintensionfrequentlyandadjustthachaintensionas required.See Chain Tensionsection. • Move On/Stop switchto the Stop position. • Replace the old chain when it becomes worn or damaged. • Use only the Low-Kickback replacement chain specified in the repair parts list. The correct replacement bar and chain is also specified on a decal located on the chain saw. • See your Sears Sen_ce Center to replace and sharpen individual cutters on your chain. • Remove bar clamp nuts. • Remove bar clamp. • Remove the old chain. DriveUn_ • Place chain over and behind clutch. • Fit the bottam of the drive links between the:teethin the sprocket nose. • Fit chain drive links into bar groove. • Pullguide bar forward untilthe chain is snug in the guide bar groove. • Installthe bar clamp. • Install bar clamp nuts; finger'tighten only.Do not tighten any further at this point. Bar Clamp Bar Clamp Nuts •Tum adjusting screw on bar to move the tensioning rack as far as it will go toward the front of the bar. BarClampNuts CHAIN ADJUSTMENT See "Chain Tension"in Maintenance section. TenslonlngRack 14 CLEAN FUEL FILTER To clean fuel filter, drain your unit by runningdry of fuel, remove fuel cap/retainer assembly from tank. Pull filter from tank and remove from line. Clean with mild detergent and rinse..Dry.thoroughly,reassemble. • CARBURETOR ADJUSTMENT WARNING: The chain will be moving during most of this procedure. Wear your protectiveequipment and observe all safety precautions. During the low speed mixture adjustment recheck idle speed after each tum of the screw. The chain must not move at idle speed. Carburetor adjustment is c_ and if done improperlycan permanently damage the engine as well as the carburetor. If you require further assistance or are unsure about performing this procedure, call our customer assistance help line at 1-800-235-5878. Start motor,let it runfor 3 minutes, and proceed tothe adjustment section. If engine does not start, refer to troubleshootingchart or call 1-800-235-5878. If engine performance is acceptable at the preset positionsand there is no chain movement at idle, no further adjustment is necessary. ADJUSTING PROCEDURE, Idle Speed-T Allow engine to idle. Adjustspeed until engine runs without chain movement or stalling. • Turn clockwiseto increase engine speed if engine stalls or dies. • Tum counterclockwiseto decrease speed. No furtheradjustments are necessary if chain does not move at idle speed and if performance is satisfactory. Low Speed Mixtura-L Allow engine to idle. Then accelerate the engine and note performance. If enOld fuel, a dirty air filter, dirty fuel filler, gine hesitates, bogs down, or smokes or flooding may give the impression of during acceleration, tum mixturescrew an improperly adjusted carburetor. clockwise in 1/16-turnincrements until Check these conditions before adjustperforrnsncs_s_,atisfactory. Repeat this ingthe carburetor. The carburetor has been carefully set at procedure as necessary for proper adthe factory.Adjustments may be neces- justment. After completingadjustments, check for acceleration and chain movesary if you notice any of the following ment at idle. Reset if necessary. conditions: • Chain moves at idle. See "idle Speed" High Speed Mixture-H under adjusting procedure. DO NOT operate engine at full throttle for prolonged periods while maidng ad• Saw will not idle. See "Idle Speed" and "Low Speed Mixture'under adjustments. Damage to the engine can occur.Make a test cut. Based on perjusting procedure. • Engine dies or hesitates when it formance of the saw while cutting, adshould accelerate. Sea "Acceleration just the high speed mixturesetting in 1/16-tumincrementsas follows: Check" under adjusting procedure. • Loss of cuffingpower. See "High • Ckx::kwiseuntilsaw has gcod power in Speed Mixture H" under adju_ng tha cutwith no _. Do not adjust procedure. bysound orspee butj.dgebyhow weUthe sew performs in the cut. There are three adjustmentscrews on • Counterclockwiseif the saw has the carburetor. They are labeled H, L, speed, but dies in the cut or lacks and T. They are located in the area just power in the cut. above the primer bulb. After completingadjustments, check for CARBURETOR PRESETS accelerationand chain movement at When making adjustments, do not force idle. Reset if necessary. the plastic limitercaps beyond the Acceleration Check stops or damage will occur. If the ongins dissor hedlatss instsadof If carburetor presets are not needed, sccelarating, turnthe low spesd mixture proceed to "Idle Spead-T." adj_nt counterdcclodseuntilyou •Tum beth mixture screws,counterhave smoothaccela_ with no chain .ql_o_wiea untilthey stop. movementat idle.Recheck and adjust as • TdrWthe idle speed screw clockwise untilit stops. Now tum counterclock- necessa_ for acceptableperformance. wise 4-1/2 full turns. Prepare your unit for storage at the end of the season or if if will not be used for 30 days or more. WARNING: • Allow the engir_ to c_01,'_mdSecure the unit before storing or.t_an_.. rig. • Store chain saw and fuel Jnawell ventilated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, fumeces, etc. • Store chain saw with all guards in place and position chain saw so that any sharp objectcannot accidentally cause injury. • Store chain saw well out of the reach of children. tive in minimizingthe formation of fuel gum depositsdudng storage. Add stabilizer to the gasoline in the fuel tank or fuel storage sontainer. Followthe mix instructions-foundon stabilizercontainers. Run engine at least 5 minutes after adding stabilizer. CRAFTSMAN 40:1, 2-cycle engine oil (air cooled) is especially blended with fuel stabilizer. If you do not use this Sears oil, you can add a fuel stabilizer to your fuel tank. ENGINE • Remove spark plug and pour 1 teaspoon of 40:1, 2-cycle engine oil (air cooled) through the spark plug open° ing. Slowly pull the starter rope 8 to 10 times to distr_ute oil. EXTERNAL SURFACES • Replace spark plug with new one of If your chain saw is to be stored for a recommended type and heat range. pedod of time, clean it thoroughlybe• Clean air tilter. fore storage. Store in a clean dry area. • Check entire unit for loose screws, • Lightlyoil external metal surfaces and nuts, and bolts. Replace any damguide bar. aged, broken, or worn parts. • Oil the chain and wrap it in heavy pa- • At the beginning of the next season, per or cloth. use only fresh fuel having the proper gasoline to oil ratio. FUELSYSTEM OTHER Under Fueling Engine in the Operating Section of this manual, see message • Do not store gasoline from one season to another. labeled IMPORTANTregarding the use of gasohol in your chain saw. • Replace your gasoline can if it starts to rust. Fuel stabilizer is an acceptable altema- 16 TROUBLE SHOOTING CHART TROUBLE CAUSE REMEDY Engine will not start orwill run only a few seconds after starting. • Ignition switch off. • Move Ignitionswitchto ON. • See "StartingInstnJctions." • RII tank with correct fuel mixture. Engine will not idle property. Engine will not accelerate, lacks power, or dies under a load. tank-er_ty. i FuSl Eqgine flooded. Spark plug not fidng. • Fuel not reaching carburetor. • Carburetor requires adjustment. • None of the above. • Idle speed set too high or too low. • Low Speed Mixture requires adjustment. • Crankshaft seals wom. • Compression low. • None of the above. • Install new spark plug. Check for dirty fuel filte_ replace. Check for Idnked or splitfuel line; repair or replace. • See "CarburetorAdjustments," • Contact Sears Service. • See "CarburetorAdjustments." • See "CarburetorAdjustments.• • Contact Sears Service. • Contact Sears Service, • Contact Sears Service. • Clean or replace air filter. • Clean or replace plug and regal}. • See "CarburetorAdjustments." : Air filter dirty. Spark plug fouled. • Carburetor requires adjustment. • Exhaust ports or muffler outlets plugged. • Compression low. • None of the above. • Contact,6ears Service. • ? : • Contact Sears Service. • Contact Sears Service. Engine smokes • Choke partially on. • Fuel mixture incorrect. excessively. • Adjustchoke. • Empty fuel tank and refillwith correct fuel mixture. Engine runs hot. Oil inadequate for bar and chain lubrication. • Air filter dirty. • High Spee_l Mixture reqmres adjustment. '. Crankcase leak. • Clean or replace air filter. • See "CarburetorAdjustments." • Fuel mixture incorrecL • Spark plug incorrect. • High Speed Mixture set too lean. • Exhaust ports or muffler-outlets plugged. • Carbon build-up on muffler outlet ecmen. • Fan housing/cyUnder fins dirty. • None of the above. • See =Fuel_g Your Unit." • Replace with correct plug. • See "CarburetorAdjustments." • Contact Sears Service. • Contact Sears Service. • Clean spark arrestor screen. • Clean area. • Contect Seers Service. • Fill oil tank. • Contect Seare Service. : Oil tank empty. Oil pomp or oil filter dogged. • Guide bar oil hole • Remove bar and dean. bleck . .i,,- P TROUBLE SHOOTING TROUBLE CHART- Continued CAUSE REMEDY 1 Chain moves at idle speed. • Idle speed requires adjustment. • Clutch requires repair. • See "CarburetorAdjustments." • Contact Sears Service. Chain does ==Chain tension too not move tight. • Carburetor requires when engine is accelerated. adjustment. • Guide bar roils pinched. • Clutchslipping. • See "Chain Tension." Chain clatters • Chain tension incorrect. or cuts roughly • Cutters damaged. • Chain worn. • Cutters dull, improperly sharpened, or depth gauges too high. • Sprocket worn. • Chain installed backwards. • • • • Chain stops within the cut. • Chain cutter tops not filed fiat. • Guide bar burred or bent; roilsuneven. • Clutch slipping • See "Sharpening • Cutters damaged on one side. • Chain dull on one side. • Guide bar bent or wom. • See "Sharpening Chain." Chain cuts at an angle. • See "CarburatorAdjustments." • Repair or replace. • Contact Sears Service. See "Chain Tension." Contact Sears Service. Rssharpen or replace chain. See "Sharpening Chain." • Contact Sears Service. • Install chain in fight direction. Chain." • Repair or replace guide bar. ; • Cont;=ctSears Service. • See -sharpening Chain." • Replace guide bar. If situationsoccur which are not covered in this manual, use cars and good judgemenL If you need assistance, contact Sears Service or the CUSTOMER ASSISTANCEBELPUNE at 1-800-235-5878. U. S. EPA/CALIFORNIA maintenance of your lawn and garden equipment engine. EMISSION CONTROL Your emission control system includes WARRANTY STATEMENT parts such asthecarbure-tor andtheignitionsystem. Where a warrantable condition exits, SEARS will repair your lawn and garden equipment engine at no cost to you. ExOBLIGATIONS penses covered under warranty include The U. S. Environmental Protection dlagnosis,parts and labor. Agency/Cailfomia Air Resources Board and SEARS, ROEBUCKAND CO., USA MANUFACTURER'S WARRANTY are pleased to explain the emissions COVERAGE-control system warranty on your lawn If any emissions related part on your enand garden equipment engine. All new gine (as listed under EmissionsControl utility and lawn and garden equipment Warranty Parts USt) is defective or a deengines must be designed, built, a.nd fact in the materials or wofio'oanshipof equipped to meet the stringent anti- the engine causes the failure of such an smog standards. SEARS must warrant emissionre ated part, the part will be retheemisaioncontrolsystemonyourlawn paired or replaced by SEARS. " , amlgardene.g,ulprnsntengineforthepe- OWNER'SWARRANTY RESPON" _ of time I,stedbelow pmwded there SIBILITIES -has been no abuse, neglect, or improper As the lawn and garden equipment en18 " "_6UR WARRANTY RIGHTS AND gineowner,you are responsible for the shall be warranted for the period performance of the require.a malnte-, nance listed in your Owners ManuaJ. SEARS recommends that you retain all receipts covering maintenance on your lawn and garden equipment engine, out SEARS cannot deny wan_ solely for the lack of receipts or foryour failure to ensure the performance of all scheduled maintenance. of time up-to the first scheduled replacement point forth at part. DIAGNOSIS - The owner shall notbe charged for diagnoatic labor which leads to the daterminationthat a warranted part is defective if the diagnosticwork is performed at an approvedSEARS servicing As the lawn and garden equipment englne owner, you should be aware that SEARS may deny you warranty coverage if your lawn and garden equipmant engine or a part of R has failed due to abuse, neglect, improper maintenance, unapproved modifications, or the use of parts not made or approved by the origb nal equipment manufacturer. You are responsible for presentingyour lawn and garden equ=pmentengine to a SEARS authorized repaircenterassoon as a problem exists. Warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have any questionsregardingyour center, , _ CONSEQUENTIAL DAMAGESSEARSmaybeliablefordamagasto?ther angine componants caused bythe lalb ureof awarrantedpartstillundarwarranty. warranty rights and should contact yourresponsibilities,you nearest authorized service center or call SEARS at 1-800-473-7247. WARRANTY COMMENCEMENT DATE - The warranty period beduinson the date thelawn and garden equipment engine is purchased. LENGTH OF COVERAGE -This warranty shall be for a period of two years from the initial date of purchase. dified parts. HOW TOFILEACLAIM If warrant, WHAT IS NOT COVERED - All failures caused by abuse, neglect, or improper maintenance are not covered. ADD-ON OR MODIFIED PARTS -The use of edd-on or _ p=ts can I_, .__go_bfor (tsalicwing a wananty _1€1_IL oF-J._r'to is not liableto cover failures ofwarranted partsoausedbythe useof add-on or mo- service center or call 1-800-473-7247. WHERE TO GET SEARS at SERVICE -servicecenters. WHAT IS COVERED -- MAINTENANCE, REPAIR OR OF PARTS -- AND REPLACEMENT - REPAIR OF EMISSION RE- LATED PARTS-- Reg_r or replacement of any warranted par_Willbe performed at no charge to .the owner at an approved_SE/_RSservicing center, If you haveanyquestionsre_ardingyour warranty rights and responsibilities,you should contact your nearest aumorlzed service center or call SEARS at 1-800-473-7247. Any SEARS approved replacement part used in the performance of any warranty maintenance or repair on emise=onrelated parts wiU be provided without charge to the owner if the part is under warranty. WARRANTY PERIOD-Any warranted part which is not sched. uledfor replacement as requiredmalntenance, orwhichisscheduled only for regular inspectionto the effect,of "repair or replay_as necessary" shall be warrarfft_ for 2 years. Any warmntedpartwhichlescheduledformplacement as required maintenance 1. 2. EMISSION CONTROL TY PARTS LIST-- WARRAN- Carburetor IgnitionSystem a. Spark Plug, covered up to maintenance schedule. b. IgnitionModule MAINTENANCE STATEMENT-The owner is responsiblefor the performance of all required maintenance as defined in the owner's manual. REPAIR PARTS I 5O 51 19 23 18 17 3O 5 Pem'_lon I_f Pall No. 24. 53O0712._ Ct_k Vldve 28. W1m-Tltmt_ 28. CMch CO_ 29. 30. Nut- Bar Moum_ CIx_ Lev_ 31. 7. _ Gmmma-.C;_ Knob 32. 33. 34. 35. 10. 530047061 Clut_ Dram AN'y._ w/Brg. + : 11. 530015611 ' W_h_" - Clutch i 12. 530O14949 Q,t=h/u_'y. ; 38. 13. S30_8227 Sw_:h Lev_ 14. 530016149 Sw_ s_ 40, 15. 5300_264 P,_p-B_zeVent 41. 16. 530015922 NUt 17. s300_geso _ln C_cher 4_ 18. 5.30015814 _w 43. 19. 530015907 Nuhw-Thmst 44. 20. 71-3_9 45. 21. 71-36596 EW_-lS" 48. DustSeal 47. 48. BxrMoumlr_ PIm 53ooloe46 53oo16oeo 53oo16o64 53oolg2o6 530049477 530038373 53oo3"/_1 53o_o18_ 530015775 "rdggw& i.od_ 2. 3. 530_6119 S300378_ Kit oz P.mp_t Ond.5O,$1&4S) 5300471_; 530016133 530047663 530O1602O 5300181_2 _0015O14 S300_/_>0 5O0015_0 53003"/7'_ S300_4 Screw Se_I Block Bbow.-O_ Pk:k.p PIdPUpO_er Oi Rter Plug-OiF_w F_l.lne Part No. 49. 50. 51. 5P, 83. 54. 845, $6. 57. 58. 530015940 530037485 530068232 5300158_ 53004,g_ 530027531 5300_817 5300_1209 530015127 530016134 D_crlptlon Screw St_r_ H4mdk_ Rope_t ;crew Fan Housk_ S_,x P,_y Ass_ I_ Fuel Cap Au'y. w/Retldner Bolt-Bar Screw Screw Won_ Gur Sp_) 8crow FrontHandle 2O Ref. Not Shown 83OO87619 530058_4 530053819 l_mll,.-IFlm Hou_ REPAIR PARTS 2 14 12 13 18 3 4 5 27 16 6 34 25 36 29 41 37 I 35 Ref. 1, !2. Pan NO. 5300_1163 5300_77_ 530016101 G300_/804 _300697_ 6. 7. 6. 9. 10. 11. 12. 13, 14. 15, l& ,530019239 530015810 530O4970O 530016187 530018102 530053184 530038318 5300_8317 ,S30049244 530047213 530069216 17. 18. 19, 20. 21. 53OO1578O 71.-88849 Part No. BarWrw_ Foam-AirRIt_ Nut AirFatorHom_ ClrburaorI_ (_ncL 12 & 15) Catb.Ga4dce Screw _Adap_' Scow. Scowl cye_ S_,Cd LV,¢_Cap,-H_h ume, u Cap--Low Orcmrn_-Caub .,_just _,..F'u_0o ,,um'y. PdmerLk'mI_ (Stud P,*) 53OO696O6 53OO69604 _".5,,_¢2ge05 830O15697 Zk_004?0e2 (IneL 22,e-2a) P_tonRk_0 _PIn _ Au'yo !28. I_mdplk_ so_&e_._. 27. 28. 29. 530047027 G300_/9_ 5300161_ 530047442 530O69606 3O. 31. _.. 33. 34. 35. 53O052296 ,G30014,_2 5300376_. S3001g_21 53OO4987O 530047207 w_ HL.,_ _. 36. _10037813 37. 5300361_ 38. 5300161_2 3O. 5300¢Qg77 40. 530015814 41. 42. 530040'714 43. 53OO40715 Not6_ow_ 5300_8486 _Sb_lpoe_lo_ I._d IE_ 6P_ud_t Kit ,17.19&33) Ho_ b_lator MUSI_ MumerBackPlate u_ omu_ Sp_ s_e_ _ Modu_ CI_InB_I_ lot 8eal_ud-lS" 21 38 REPAIR PARTS e P_'buft_ Jmumblv lot Numb_/_g'/_ . 8 I Flof. 1, 2. 3, 4. 5. 5. 7. 8. 22 6 23 For the repair or replacement parts you need delivered directly to your home Call 7 am - 7 pm, 7 days a week 1-800-366-PART _(1-800-366-7278) Para ordenar piezas con entrega a domicilio - 1-800-659-7084 For in-house major brand repair service Call 24 hours a day, 7 days a week 1-800-4-REPAIR (1-800-473-7247) Para pedir servicio de reparaciSn a domicilio - 1-800-676-5811 For the location of a Sears Parts and Repair Center in your area Call 24 hours a day, 7 days a week 1-800-488-1222 For information on purchasing a Sears Maintenance Agreement or to inquire about an existing Agreement Call 9 am - 5 pro, Monday-Saturday 1-800-827-6655 When requesting service or ordering parts, always provide the following mformabon: SF.AR$ • ProductType • Part Number • Medef Number * Part Description America's Repair Specialists