Download Chapter 6 Advanced Operation

Revision History
Revision
code
Date
3
June 2000
Revised content
Addition of 3G3FV--CUE, changes accompanying 3G3FV software changes, changes to
some display messages, and other changes and
improvements. Specific changes are as follows:
Front matter: Added General Precautions, Warning
Label information, and About this Manual. Model
numbers changed in Checking before Unpacking.
Changes to information on changing Digital Operator
language.
Pages 1-2, 1-6, and 3-13: Changes to information on
changing Digital Operator language.
Page 1-5: Changed second item in Frequency References.
Pages 1-10, 2-10, 2-46, 3-2, 5-13, 5-20, 5-34, 6-16,
6-51, 6-59, 6-50, 6-62 to 6-65, 6-71, 6-74, 6-92, and
9-17: Added notes.
Page 1-11: Added section on new functions.
Pages 2-4, 2-6, 4-2, and 8-13: Changed warnings.
Page 2-10: Added to Multi-function analog input signal level.
Page 2-21: Added information on frequence reference variable resistor and added graphic and note to
bottom of page.
Pages 2-26 to 2-28: Replaced Wiring on Input Side of
Main Circuit and added information on calculating
inverter input power supply capacity.
Page 2-30: Added information on inverter–motor
cable length.
Page 2-35: Added setting for L3-04.
Page 3-14: Added U1-32 to U1-38.
Pages 3-25, 6-2, 6-9, 6-13, 6-31, and 6-35: Added E2
to E5 and F7 to F9.
Page 3-30: Added section 3-8.
Pages 5-4 to 5-5, 5-8, and 5-10: Changed setting
range to 0 to 4 and added descriptions and notes.
Pages 5-9: Added information to “2 to 39” setting and
deleted “This setting can’t be used with flux vector
control.”
Pages 5-15 and 5-18: Added setting “17.”
Page 5-19: Added section section 5-2.
Pages 5-22 and 5-28: Added “PG Direction,” “Minor
Fault,” and “V/f over Setting” to table.
Pages 5-22 and 5-41: Added setting “2.”
Page 5-24: Corrected voltage for setting of 7 to “9 V.”
Pages 5-27, 6-6, and 6-27: Changed setting range for
E1-04.
Page 5-28: Added information to introduction.
Pages 5-30 and 5-44: Added F1-14.
Pages 5-33 to 5-34: Added E1-02
Page 5-38: Added C5-08.
Pages 5-39 and 5-48: Added information on 3G3FV-CUE/CE.
Page 6-5: Added sections 6-1-3 to 6-1-7.
Page 6-6: Added section on startup torque compensation.
Pages 6-7 and 6-50: Changed percentage to 100%.
Pages 6-7, 6-12, 6-28, and 6-34: Changed setting
range for E2-03 and added note.
R-2
Pages 6-8 and 6-29: Changed descriptions of E2-05
and E2-06.
Pages 6-12 and 6-34: Added E2-10.
Page 6-14: Made corrections to b7-01 and b7-02.
Page 6-30: Added sections 6-3-8 and 6-3-9.
Page 6-36: Added section Setting Operation Source
Selection (b1).
Page 6-37: Added b2-08.
Page 6-38: Changed factory settings for b3-02 and
b3-03.
Pages 6-41 to 6-43: Added PID control functions.
Page 6-45: Changed end of setting range for b5-01 to
“4.”
Page 6-54: Added information for settings for second
motor.
Page 6-56: Changed information for binary input setting.
Page 6-56: Made changes to analog monitor card settings.
Page 6-57: Added F8 and F9.
Page 6-58: Added settings 15, 16, 17, 1E, 30, and 31.
Page 6-60: Added information on external baseblock.
Page 6-65: Add setting 1E.
Page 6-73: Added C and D.
Pages 6-74 and 6-75: Corrected analog input characteristics.
Pages 6-76, 6-79, and 6-90: Corrected information on
setting ranges.
Page 7-77: Added information after second bullet.
Page 6-81: Changed factory setting for L3-03 and deleted note.
Page 6-82: Added setting 3.
Page 6-89: Changed setting range of L8-02.
Page 6-90: Changed “10%” to “5%” and added information.
Page 6-92: Added sentence and note to o2-03.
Pages 7-2 to 7-48: Added/corrected parameters.
Page 8-2: Added to introduction.
Pages 8-5 and 8-5: Added/changed PGO, DEV, OPR,
EFO, EF8, E-15, BUS, CPF21, CPF22, and CPF23.
Page 8-8: Added/changed PGO, DEV, EFO, ERR,
CALL, E-15, and BUS.
Pages 8-9 and 8-10-: Added/changed OPE03, OPE07,
OPE08, and ERR.
Page 8-15: Information added on vertical axes.
Page 8-17: Information added EF.
Pages 9-7 and 9-9: Diagrams changed and cards added.
Pages 9-13 and 9-14: Diagrams changed and model
numbers changed.
Pages 9-14 and 9-15: Note added and minimum connection resistances added to table.
Page 9-18: Losses added to table.
Page 9-20: “1120” changed to “120” and “182.8”
changed to “182.5.”
Pages 9-22 to 9-25: Models changed.
Page 10-5: Model numbers deleted.