Download WAVE Air Purifier User Manual

Operating Instructions
WAVE Air Purifier
800-293-9577 www.wavehomesolutions.com
Operating Instructions
Timer
Setting
Speed
Setting
ON / OFF
Button
UV/ ION
Button
HEPA Change
or Clean
API Display
Timer
Reset
ION
Auto
Air-Flow
UV
BEFORE FIRST USE please follow the instructions below:
Upon removing the unit from the box:
1.
2.
3.
4.
5.
6.
7.
Remove the unit from the plastic bag
Remove the cover
Remove the Styrofoam
Twist latch to allow the filters to be removed
Remove all 3 filters
Remove filters from the plastic bag
Replace filters in the following order
a. TiO2
b. Carbon
c. HEPA
8. Once filters are placed back inside the unit turn the latch to keep the filters in place
9. Securely replace the cover
10.Unit is ready for use
c. b. a.
Operating Instructions
1. Press
to start the unit.
2. The default setting for the unit is Speed II. To change speed settings press
. Each time the button is pressed,
the unit will cycle through the different FAN speeds (I→II→III→Auto).
3. The unit is equipped with a TIMER feature. To set a desired interval of time press
1Hr→2Hr→4Hr→6Hr→8Hr → cancel timer. As the user cycles through the different time intervals, the different times
will be shown (i.e.
)
4. The default setting is to have both UV/ION 'ON'. The UV/ION button
LCD will display
5. For AUTO mode (Press
toggles this feature ON and OFF. The
when both UV and ION are on.
until the LCD display shows “AUTO”). In this mode the API (Air Pollution Index) will
control the unit's speed. The “API” measures the air quality and adjusts system performance automatically. The API
Scale is a visual representation of the air quality and will change depending on the air quality.
“Low Particle Count” “High Particle Count"
6. Maintenance (HEPA, Tio2 Catalyst, Carbon filter and UV Lamp). When the HEPA filter icon
blinks (after
approximately 2 years / 17,500 hours of operation) it is time to replace the HEPA, Carbon filter and UV Lamp. Contact
WAVE Home Solutions for the replacement kit. Follow the instructions that will accompany the replacement kit on how
to replace the UV Lamp. Once the contents of the replacement kit have been installed use a paperclip (or similar
object) to press and hold the reset button for 3 seconds. This will reset the HEPA notification icon on the LCD. The
included HEPA filter can be cleaned when so desired to maintain system performance.
7. To remove the front cover (see Figure A. on page 10), grasp the bottom of the unit and pull up and away from the unit.
Once detached from the unit, lift the cover upwards.
8. To remove the HEPA filter for cleaning or replacement, turn the lock as to allow for the pre-filter and HEPA to be easily
removed from the unit. Pull on the tab located at the top of the filter to remove.
Operating Instructions
9. To Clean the HEPA filter, remove the black foam pre-filter from the
HEPA filter (these are attached with Velcro). Shake off or wash the pre-filter
to clean any dirt and/or particulates from the media. Use a vacuum cleaner to
clean off the HEPA Filter.
10. Filter Sequence (from the bottom up)
Tio2 catalyst→Carbon filter→HEPA filter→Pre-filter
After replacing the HEPA filter,
Lock the filters into place by turning the lock.
11. To replace the unit's front cover (see Figure B. below), first fit the top of the unit into place and slowly press the bottom
as to allow the bottom clips to catch.
12. Remote control. The unit comes with an included infrared remote control. To use the remote control, point the remote
in the direction of the LCD display.
1
2
Figure A.
Figure B.
2
1
To remove cover
To replace cover
Operating Instructions
WAVE Home Solutions Warranty
Wave Home Solutions warrants the WAVE Air Purifier to be free from defects in material and workmanship subject to the
conditions and limitations hereinafter described. The warranty period is 1 year from the date of purchase.
Warranty claims are to be made to WAVE Home Solutions. The customer shall contact WAVE Home Solutions at
1-800-293-9577 to obtain the address of where the defective unit is to be shipped (at customer's expense) along with a copy of
the original invoice. WAVE Home Solutions will repair and return the unit to the customer at WAVE Home Solutions expense.
WAVE HOME SOLUTIONS WILL NOT BE RESPONSIBLE FOR
Ÿ Normal maintenance as outlined in the installation and servicing instructions or owner's manual.
Ÿ Damage or repairs required as a consequence of faulty installation or application by others.
Ÿ Failure to start due to voltage conditions, blown fuses, open circuit breakers or other damages due to the inadequacy or
interruption of electrical service.
Ÿ Damage or repairs needed as a consequence of any misapplication, abuse, improper servicing, unauthorized alteration, or
improper operations.
Ÿ Damage as a result of floods, winds, fires, lightning, accidents, corrosive atmosphere, or other conditions beyond the
control of WAVE Home Solutions.
Ÿ Parts not supplied or designated by WAVE Home Solutions.
Ÿ ANY SPECIAL INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY NATURE
WHATSOEVER.
Ÿ Some states or provinces do not allow the exclusion of incidental or consequential damages, so the above limitation may
not apply to you.
800-293-9577 www.wavehomesolutions.com