Download Luminic-IPL
Transcript
Luminic-IPL IPL-1011 User Manual For your safety and correct usage of our device We strongly recommend reading through this user manual. Table of Contents o I mportant S afety I nformation ----- 4 o T he N ame -----10 o H ow of to use E ach P art L uminic SIPL-10? o O peration F or H air removal o O perating F or S kin C are o U ser T ips -----12 -----13 -----23 ----- 27 o T roubleshooting -----28 o R eplacing L amp -----29 o FAQ ----- 30 o P roduct S pecification ----- 31 o W arranty ----- 32 o T reatment R ecord S heet ----- 33 We appreciate for the purchasing Luminic SIPL-10. For the safe treatment and caring, you should be well-acquainted with this user manual. Particularly, please follow RESTRICTION before the treatment. Danger The following instructions contain important safety information, which may lead to death or critical injury if not followed. Warning Injury may occur when the following instructions are not followed. Restriction Refrain from administering if the person or the ara to be treated is affected by one of the following conditions. 3 Important safety information Danger The following instructions contain important safety information, which may lead to death or critical injury if not followed. Be sure to keep the metal pins of the power plug free from dust or moisture. When cleaning, use a cloth-cleaner Using multiple products on a single outlet is not recommended. Keep the unit and the power plug away from heaters or stoves. DO NOT pull the power plug by force or with wet hands. 4 Neither bending the power cord nor placing heavy objects on the power plug is recommended. The unit is not designed for cleaning with water. Always clean with a dry clothcleaner before storing the unit. •DO NOT operate the product in elevated or wet places. •Ensure that the unit is turned off when connecting or disconnecting the power plug. •DO NOT leave the unit connected to the power when not in use over a long period of time •Disconnect from the power supply when cleaning the unit. Major safety instructions Please do not dissemble the product discretionally. If customer dissemble product discretionally, free repair is not available. Please do not fill up the air vent of fan during usage of main body or hand piece. In case that ventilation does not work, it could cause the trouble on main body. Please do use the provided cord only by our company in case that power plug and cord are broken. 5 Warning Injury may occur when the following instructions are not followed. DO NOT use mucous membrane area such as lips,anus, or vagina, and this will cause a serious skin trouble. Product use should be limited on severe corium pigment, darkening, moles, age, spots, or birthmarks, which should be taped over before the treatment DO NOT touch the lamp with bare hands. If there is any thouch, you can get burned. 6 Always keep the hand piece in contact with the skin when the beam is on. DO NOT beam direct on to unshielded eyes. DO NOT use the unit to eyes or eyelids The unit is not to be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given instruction. DO NOT use this unit for your face or neck for your safety 7 Restriction Refrain from administering if the person or the area to be treated is affected by one of the following conditions. A person whose activity was outdoors under strong sunlight, or who has received tanning treatment within the last 4 weeks. A person whose skin color is black, or dark brown (page 18) Pregnant women or the breast during the breast-feeding period. 8 Acne treatment medication (such as Accutane), whitening treatment, Retin A ointment, or cosmetics with retinol composition within the last 7 days. DO NOT USE TO THIS AREA... Skin area with tatoos or permanent makeup. Skin area with severe pigment discoloring, or with thick or dense hair. Skin affected by diabetes or other skin diseases. DO NOT USE TO THIS DEVICE IF YOU... have used steroid products over an extended period of time, causing the skin to become thin. are photosensitivity or sun allergy patients (porphyria, polymorphous light eruption, transient urticaria, erythematous). are administered with a heart pacer, insulin pump, or any other medical device Yes Yes Yes have had radio-active treatment or chemical therapy within the last 3 months Yes have had skin cancer or has a higher chance of contracting skin cancer Yes have used medication or lotion with characteristics of higher photo-sensitive reactions within the last one month Yes 9 The name of each part ④ ② ⑤ ① ⑥ ③ ⑦ ① Power SW : Power on/off ② Power Level : select the power level. ( from level 1 to level 5 ) ③ Reset : this switch is located at the bottom To activate reset function, press and hold more than 3 seconds ④ Power Level: 1(min), 2, 3, 4, 5(max) ⑤ Charge: When this is red, Charging: When green, ready to flash ⑥ Lamp: When this is green, lamp is OK, when this is red, the lamp should be replaced with new one. After replacement the reset should be done. Make sure to get after service in case green LED blinks indicating fan's stoppage. Be sure not to use SIP-10 in case red LED blinks indicating the inside temperature of main body raised up, then, stop using for the time being. If possible, it is not recommendable not to use SIP-10 for the long time. ⑦ Mode Switch : Hair Removal (downward), Skin Care (upward) 10 Hand piece ① ② ① Flash button ② Touch sensor : for safety, checking the touch state between the skin and the aperture of lamp module. Accessory ① ② ④ ③ ① ② ③ ④ User Manual Power Cord Lamp (Hair Removal , Skin Care) Cooling Pack (Option) 11 how To use lumInIC Ipl101? ① START ② Read ‘RESTRICTION’ Yes ③ Skin Test Any reaction? No Yes ④ Shaving (For Hair Removal Only) ⑤ Cleaning Keep clean & dried ⑥ Select Skin type (Adjust Level) ⑦ Treatment 12 STOP Operation For Hair Removal Hair Growth Hair normally grows in three phases Anagen phase (growing phase) The concentration of melanin is highest when the hair grows most actively from the root. Melanin is the key factor to make the pigmentation of the hair, such that the darker the hair is, the more melanin there is in its root. Hence, controlling the melanin level is the key to this method of improving hair-growth efficacy. The most effective time for the IPL treatment is in the anagen phase of hair growth. Catagen phase (degradation phase) In decline period, hair growth stops, the pore and root shrink, and the old hair is then fallen out. Telogen phase (resting phase) Once the old hair is fallen out, a new hair will be slowly grown in the same root. The old root remains empty until the biological cycle restarts and a new hair grows in the place of the old one. 13 Operation principle • Luminic SIPL-10 removes hair by intense pulsed light which heats up the hair shaft and it’s root. • Through light transformation, the darker hair receives more heat. • This process stops the hair growth early, in the anagen phase. • Hairs are usually in different states of the hair growth’ s cycles. • Hence, more than 4 treatments are required to give you long-lasting hair-removal successfully. 14 1. Pre-Operation ※ Before the treatment, read ‘RESTRICTIONS’ cautiously for your safety. 1) Skin Test ▶ Be sure that your skin is in a normal before star ting the treatment. ▶ For the first-time use (or after increasing levels), test the skin reaction by emitting on the arms or back of the hands if there is any trace of vesicles, blisters, burns, or any other reactive symptoms on any other area not exposed to the beam. ▶ If you see any of the listed symptoms in 30 minutes, DO NOT start the treatment. 15 ▶ If serious stinging occurs in the exposed area, STOP the treatment immediately. ▶ You skin shows slight redness, prickles, tingles, or feels warm. This reaction is harmless and you can start the treatment if this disappears quickly. 2) Scheduling ▶ A typical full hair growth cycle may take 18~24 months. During this time multiple Luminic SIPL-10 treatment may be required in order to achieve long term hair removal • Treat the entire place where you want to remove the hair in one time. • Apply an ice pack every time in the place where you want to repeat the treatment. It is highly recommended to apply an ice pack in the place where the skin is sensitive and hair is strong such as under the arms part especially. • Apply an ice pack on the place where you treated as long as hot temperature is just cool down, approximately 3 to 8 seconds. • Try 2nd treatment as partial in the place where the hair is remained only after 3days from the 1st entire treatment. • Perform the entire treatment and partial treatment as a couple and repeat the couple treatment in every two weeks. 16 1st Treatment 2nd Treatment 3rd Treatment 4th Treatment 5th Treatment 6th Treatment 7th Treatment 8th Treatment D-day D + 3day D + 14day D + 17day D + 28day D + 31day D + 42day D + 45day Entire treatment Partial treatment Entire treatment Partial treatment Entire treatment Partial treatment Entire treatment Partal treatment • Repeat the entire treatment and partial treatment as long as all the hairs are removed in every 2 weeks. It will take approximately 7 to 8 weeks in total. 3) Shaving ▶ Shave with razors to ensure the light energy is channeled to the hair root. ▶ DO NOT remove the hairs by means of wax, epilator, tweezers, or depilation cream. Have your hairs cut by 1mm or so. This helps you check the treatment effect easily. After flashing, you can see if the hair is burned out or not. 4) Cleaning ▶ Clean the treatment skin area and make sure it is dried and free from grease or oil. 17 5) Checking if the MODE is positioned to ‘HR’ mode. ▶ Insert HR lamp module into the Hand Piece. ▶ Set the bottom switch to the ‘HR’ mode. ▶ Check if the LED lamp on the level is ‘RED’ color. ▶ Proceeding the treatments on dark brown, black skin, or on the tanned skin may result in adverse effects like burns blisters, coloring/discoloring on the skin, the inflation of follicles, etc., and not recommended to be treated. 18 6) Setting the Energy Level ※ In case of initial usage of SIPL-10, please start with STEP 1 for safer treatment ▶ You can get more comfort and effective treatment from proper energy level. ▶ By pressing STEP button, increase or decrease the energy level. ▶ For the users’ safety, the energy level is back to ‘Level 1’ automatically when it is OFF and ON again. ▶ Higher step delivers you high efficiency, but may bring you more risk simultaneously. So, setting the right STEP is very important before the treatment. 19 2. Operation Checking the Lamp ▶ Before connecting the power to the unit, check the lamp position of the hand piece. ▶ Check if the lamp module color is ‘SILVER’. Turning on the Power ▶ Plug in the power and turn on the unit. Check the LED color and Setting the Level ▶ Check if the LED color is RED. If it is GREEN, then adjust the bottom switch to opposite side. Cooling ▶ Cool down the skin site with cooling pack before the treatment. Cooling eases your pain. (Option) 20 First Procedure ▶ When the READY LED becomes green, indicating that the unit is ready, place the hand piece to the skin site to treat. ▶ Press the START button. Keep pressing until you see two flashes, which is called ‘doubleshot’ and has normally 0.5~1.2sec of interval. ※ Double-shot comes from level 2. ※ The buzzer will not sound if the contact is not accurately made or the unit is muted. 3. Post Operation Sun Blocking ▶ Do not take an intensive sunbath or suntan. ▶ Apply a sun blocker to the treated areas. ▶ Avoid swimming in chlorinated water for 48 hours. ▶ Avoid applying cosmetic substances immediately after treatment 21 Using Hand Piece ▶ Wait during charging time (Ready LED indicates red) Keeping the hand piece far away from the skin for cooling lamp module down. < Charging > < Emitting > ※ DO NOT treat consecutively on to the same site more than twice or do not overlap. Filter Cleaning ▶ Please clean the lamp filter softly using cotton bud with dip in alcohol, in case the lamp filter is contaminated by dust or ashes. 22 Operating For Skin Care 1. Pre-operation ※ Before the treatment, read ‘RESTRICTIONS’ cautiously for your safety. 1) Skin Test : Please follow the Hair Removal Skin Test Method. (page 15) 2) Scheduling ▶ The total of 10 times treatments is one session. The recommended schedule is of twice or three times treatments per week and it takes 4 to 5 weeks for one session. ▶ When the beginning treatment of session, start with level 1, and increase the level from next treatment. ▶ The Power level lamp indicate the energy level while the procedure should start over from Level 1 when the treatment has been paused for over two weeks. 3) Face Cleaning ▶ D O N OT u s e a l c o h o l o r acetone with and inflammable composition. ▶ Use a peeling solution suitable for your skin type such as glycolic acid peeling 10% to remove any keratin or dead skin cells. ▶ Use non-alcohol toner when the face is dried after cleansing. 23 2. Operation Checking the Lamp ▶ Before connecting the power to the unit, check the lamp position of the hand piece. ▶ Check if the lamp module color is ‘YELLOW’. Turning Power on the ▶ Plug in the power and turn on the unit. Check the LED color and Setting the Level ▶ Check if the LED color is GREEN. If it is RED, then adjust the bottom switch to opposite side. First Procedure ▶ When the READY LED is green, indicating the unit is ready. Place the hand piece to the skin site while keeping the skin site taut by gently pulling the skin in the opposite direction. ▶ Press the START button. The buzzer will not sound if the contact is not accurately made or the unit is muted. 24 Charging and Emitting ▶ Af ter emitting a sequence of pulse, the READY LED will become red and start blinking. Wait until the LED becomes green before moving on to another site. (Tip:during recharging, keep the hand piece away from the skin site to cool down, and do not block the vent located in the hand grip.) Second Procedure ▶ When the 1st procedure has covered the entire facial area, start the 2nd procedure. ▶ Move along the site area for full coverage rather than focusing on a specific area repeatedly. Checking the Reaction ▶ After the 2nd procedure, the face should assume a slight reddish tint from the heat. However, terminate the procedure if blisters or vesicles appear on the site area. 25 3. Post Operation ▶ Apply a moisturizing mask or modeling pack as described in the process of treatment, and complete the treatment by applying moisturizer or regeneration cream and sun block lotion. ▶ From the start of the treatment and one month after the completion of 1 session, avoid direct sun exposure or apply sun block cream to protect the skin from damaging UV rays. ▶ Keep you skin moisturized to prevent it from becoming dry. 26 User Tips Check the buzzer. • The buzzer sound indicates that contact with the skin site has been made and the unit is ready for operation. Always check the buzzer sound before emitting a sequence. • Move the hand piece far away from the skin site so that the skin and the hand piece can cool down thoroughly. • Do not overlap. Try to cover every area of the skin site. Press down the hand piece • When the skin becomes excessively hot, abort the operation even during the treatment, and wait until recharging is complete before moving to another designated skin site. • Do not use hair removing on the face or neck Ease along the wrinkles • Adjust the hand piece so that the touch switch remains in contact and ease along curved contours. 27 Troubleshooting Please refer to the following table for troubleshooting before requesting service. Symptom When the unit is not oprating Checkpoint Troubleshooting Check the power connection. Make sure that the power connection is securely in Ensure the unit is connected place. to AC Power. Turn off the unit for Check if the lamp unit is 30 minutes to relieve overheating. overheated. Check if the power cord Call service for evaluation or is damaged or exposed to repair. DO NOT disassemble water. or modify for yourself. When the beam becomes Check the lamp life indicator Replace the lamp unit. weak during the procedure located on the right side of the unit. Purchase the optional lamp unit. When the illumination Check to see if the buzzer Contact the hand piece to the button does not work sounds. skin site again and see if the buzzer sounds. Check to see if the unit is set to mute. Please note that service may not be free if the request is made and the unit is found to be in perfect working condition. If the problem continues, please contact your local distributor office for further information and instructions. 28 Replacing the lamps When to replace the lamp • If the lamp is used in excess of it's lifetime, it will cause deteriorated treatment. Then, replace the lamp which blink continously • Turn the device off and unplug the cord from the electrical outlet • Grip the unit with both hands and pull out the lamp. • Don’t touch any metallic materials. • Insert a new lamp unit, Turn the device on, and use a sharp-edged tool to press the initiation button (RESET) for 3 seconds to reset the lamp life indicator. Lamp Cleaning Clean the lamp filter softly using cotton bud with dip in alcohol in case the lamp filter is contaminated by dust or ashes. 29 FAQ Q. Is the IPL harmless if I see it direct? A. Luminic SIPL-10 is designed for safe treatment. It has the touch sensor at the head of hand piece, and without touching this sensors to your skin, the light is not emitted. Q. What is the lamp life? A. Luminic SIPL-10 indicator shows you when you have to change the lamp module. Averagely, lamp life is 6,000 shots in HR mode, and 20,000 shots in SC mode. if the light intensity falls below acceptable level, it stops emitting light automatically, then you have to change to new lamp module. Q. When uses Hair Removal, do I have to remove hairs completely before the treatment? A. Just shave by 1mm of height. If you remove your hairs by waxing, epilator, tweezers, your hair follicle absorb less heat, and this will lessen the effect. Q. Can I see the hair remained after the HR treatment? A. Several hairs can be remained after the normal treatment. This will be removed automatically within two weeks because the hair follicle was affected/harmed by IPL. Do not remove the remained hairs by wax, epilator, tweezers. 30 Product Specifications Lamp Xenon Lamp Light Source Pulsed light Hair removal : 3.0J/cm2 Energy Fluency Spot Size ~ 10.4J/cm2 Skin care : 1.8J/cm2 ~ 5.5J/cm2 30 mm x 15 mm Hair removal : 470 - 1100 nm Wavelength Skin care : 420 ~ 1100 nm Lamp Life Weight Dimension HR : 6000 flash , SC : 20000 flash 1.7Kg 245mm (L) X 135mm (W) X 125mm (H) Operation Conditions Temperature Humidity Rated Power 5oC - 30oC 30% - 80% RH 230VAC , 50 or 60 Hz, 200W Storage Conditions Temperature Humidity -20oC to 80oC 0%-95% RH The design and specifications may be subject to change without prior notice in order to improve the product performance. 31 Warranty Warranty Product Name Purchased on Model Name MM DD YY Seller Serial N o. Price Warranty Service Consumer Service Information Within the warranty period Service requested within a month from the date of Replace the product o r Defects in workmanship purchase under normal use or operation. refund For defects Free-of-charge or performance during the warranty period, For the 2nd defect after the firs t repair service under the normal use or operation For defects unable to fix service After the warranty period Not applicable At minimum service provided charge Replace the product or full At refund charge Replace the product Replace the product after minimum service charging the service cost according to reflecting the depreciation The replaced product is major defect again within a Full refund Not applicable month For damages due to For the defects contributable to normal use and Replace the product At minimum charge of serviceable deteriorated performance. . service parts not on stock during the mandatory For defects due to misuse or accident. Replace the product after charging the cost. period Injuries caused by product replacement Medical bills, other normal expenses and compensation for damage Service cos t charging *Please be sure that you read the warranty and troubleshooting information before sending the unit to service. In case you send the unit to service is not out of order, just caused by misconceived defects as one of following reasons, you will be charged the cost of expenses. 1. If the defects are caused by any other means than cleaning, adjusting, instruction or installation. 2. If the defects are caused by consumer misuse. 3. If the defects are caused by sort of disaster or o ver end life of consuming components. 32 Treatment record Sheet <Record # _________> <Record # _________> No. Date Treatment Area Step 1 2 3 4 5 6 7 8 9 10 11 12 No. Date Treatment Area Step 1 2 3 4 5 6 7 8 9 10 11 12 <Record # _________> <Record # _________> No. Date Treatment Area Step 1 2 3 4 5 6 7 8 9 10 11 12 No. Date Treatment Area Step 1 2 3 4 5 6 7 8 9 10 11 12 33 <Record # _________> <Record # _________> No. Date Treatment Area Step 1 2 3 4 5 6 7 8 9 10 11 12 No. Date Treatment Area Step 1 2 3 4 5 6 7 8 9 10 11 12 <Record # _________> <Record # _________> No. Date Treatment Area Step 1 2 3 4 5 6 7 8 9 10 11 12 No. Date Treatment Area Step 1 2 3 4 5 6 7 8 9 10 11 12 34 <Record # _________> <Record # _________> No. Date Treatment Area Step 1 2 3 4 5 6 7 8 9 10 11 12 No. Date Treatment Area Step 1 2 3 4 5 6 7 8 9 10 11 12 <Record # _________> <Record # _________> No. Date Treatment Area Step 1 2 3 4 5 6 7 8 9 10 11 12 No. Date Treatment Area Step 1 2 3 4 5 6 7 8 9 10 11 12 35