Download INSTALLATION INSTF?UCTIONS

R
.-.
12~ lNP~
AmRMREmVCONTACT
[N.c.OPENONAURM,
ED REMOEDISABLE
WEN 7WC APPLIEW
SPECIFICATIONS
Oe&ction Mathod Dual Technology
Mcrowave/PiR.
~OUBLE
COvaraga
OUP~
FOR SUPERWSlON.
.USE SHIELDED WIRE FOR UL lNSTALMn~S
r
WWR
AND CIRCU~
4111
(+)(-)A
ttI-L
BOARD—
HOWINGPOSTS[21
WOOKCOVER
ONTH=E
HEN REPUCINGm
123458~!
:
. ..... ...
40ft(12m)x50ft(15m),
Oetection Pattern:
~
22 ZOnes (7 Main, 6 Mdrange,
5 Intermediate, 4 Close) plus one
.Look-down. zone.
b
WIRING ENmY HOE
AND WIRING CWNEL
IN BEE
Mcrowave:
VOlumetfic covemge.
Mounting Helghk 7.5ft nominal (2.3m),
walllcomer mounting.
Indicators Red and Green LEUS(see
LED INDICATIONS in
MICROWAE
DHEmOR
(DRO)
Diagram 4).
Alarm Relay SPST (Fore A) reed with
15-ohm protective resistor,
COnmo*.
50 mA max at 24VDC
(non-ind.ctiva).
,
LOCKINO
RELmEACCE=
W REL=SE
UN!T\
FROM
WAWPWTE,
INSEmSRWDBIVER
BUDE,
P~SSS
kUINSTLOCKING
TAB,
ANDSLIDE
UNIT
Up.
MICROWAE
SENSlnMW
CON~OL.
NRN CLOCWISE M
INCRUSE ENS~lVIN
Input VohagS 12VDC nominal.
(&J::$::::~etector
inoperative.)
Current
CIRCUIT 00ARO HOLDING TAB—
(BEND WCK IF NECEWRY
TO REMOE BOARD)
.
PIR D~CTOR
y
“LOOK-NW”
Standby
CapabiliW
LENS
25mA (40mA during
power UP).
Powersourceshouldbe
capable of at least 4 hour!
of batte~ stindby.
Operating
Temperature +14°F to +122-F
(-lo~c
to +50”C)
RED LED
(SEE BELOW
GREEN LED
(SEE BELOW
Operating
HumidiW
Up to 95Y. RH (mW.) noncondensing.
Dimensions ~-~~~~e:W
.
LED INDICATIONS:
POWER UP Red and Green LEDs on for approx.90 sem.
SUPERVISION FAILURE: Red and Green LEDs flasfdng.
ALARM: Red LED on.
WALK TEST (when selected via DIP switoh #l ~
Green LED flashesfor microwave.
Red LED flashesfor PIR.
2“ D (w/wall plat”)
(97mm x 124mm x 51mm)
Notw When Walk Testis selected, alarm relay is constantly held
leaving the detec~r in the walk test mode..
copen to prevent
Magram 4
ACCU-TRAK
INTERIOR OF DETECTOR
Walk-Test
prevent potential intruders from determining the exact
timits of the Drotected area. Tfds is accomDtished remotelv
whenever 12VDC(+) is appfied to terminal 5, or local&
when DIP switch position 3 is UP.
Ademco’$ unique ACCU-TRAK walk test feature is es6y to
use. Simply set DIP Switch #1 UP.
Both microwave
and PIR information is viewable
simultaneously
on the two LEDs, providing crisp,
immediate feedback (see below). As you enter the
protected area, ACCU.TRAK responds and lights the
LEDs when you stop moving or leave the protected area,
the LEDs extinguish immediately. In addition, the flash rate
of the microwave LED (green) is directly. pr~otiional to
speed at which movement occurs; the PIR LED (red)
bhnks aa you enter or leave each zone. This will give
precise feedback during walk testing, so that you can
easily determine the exact pattern of coverage for the
installation.
Grasn LED flashes for microwave.
Rsrf LED flashes for PIR zone crossings
,.-
Note
MAINTAINING
PROPER OPERATION
In order tf2 maintain the detector in proper vvorking
condition, it is impoftant that the following be obsewed by
the uaec
1. Power should ba provided at all times. Loss of
power 10 the unit will result in the alarm contacts
reveting to an alarm state. The uni~s DC source
should have standby power available for at least 4
hours oi oDeration duflng emergencies.
2. Units alhould never be r*aim6d or relocaiad without
the advice or &sistance of the alarm sewice company.
3. The physical surroundings
of the protected srea
should not ba changed. If furniture or stock ia moved,
or air cclnditioning or additional heating is installed, the
system may have to be readjusted by the alarm aewice
company.
Alarm relay remains continuously open when walk
test is selected to prevent leaving the detector in
the walk test mode.
LED ~sable
In some installations, it may be desirable to disable the
Alarm LED after the initial tests at installation, in order to
4. Walk-tests should be conducted frquently
(at least
wsakly]l to confirm proper coverage by each detector.
3