Download Chapter 3. Connecting to the AP - PLANET Technology Corporation.

User’s Manual
802.11b/g/n Wireless Outdoor AP
WNAP-6350
www.PLANET.com.tw
Copyright
Copyright  2013 by PLANET Technology Corp. All rights reserved. No part of this publication may
be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language
or computer language, in any form or by any means, electronic, mechanical, magnetic, optical,
chemical, manual or otherwise, without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular
purpose. Any software described in this manual is sold or licensed "as is". Should the programs
prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer)
assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software. Further, this company reserves the right to revise
this publication and to make changes from time to time in the contents hereof without obligation to
notify any person of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or registered trademarks
of their respective holders.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his/her own
expense. Any changes or modifications not expressly approved by PLANET could void the user’s
authority to operate this equipment under the rules and regulations of the FCC.
FCC Caution:
To assure continued compliance, (example-use only shielded interface cables when connecting to
computer or peripheral devices) any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the Following two
conditions:
(1) This device may not cause harmful interference
(2) This Device must accept any interference received, including interference that may cause
undesired operation.
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In
order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity
to the antenna shall not be less than 20 cm (8 inches) during normal operation.
I
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
Energy Saving Note of the Device
This power required device does not support Standby mode operation.
For energy saving, please remove the DC-plug to disconnect the device from the power circuit.
Without remove the DC-plug, the device still consuming power from the power circuit. In the view of
Saving the Energy and reduce the unnecessary power consuming, it is strongly suggested to
remove the DC-plug for the device if this device is not intended to be active.
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN
PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication
terminal Equipment and the mutual recognition of their conformity (R&TTE).
The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications
Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it.
However, special attention must be paid to the dangers of electric shock and static electricity when
working with electrical equipment. All guidelines of this and of the computer manufacture must
therefore be allowed at all times to ensure the safe use of the equipment.
WEEE regulation
To avoid the potential effects on the environment and human health as a result of the
presence of hazardous substances in electrical and electronic equipment, end users of
electrical and electronic equipment should understand the meaning of the crossed-out
wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to
collect such WEEE separately.
II
Revision
User’s Manual for PLANET 802.11b/g/n Wireless Outdoor Access Point
Model: WNAP-6350
Rev: 2.0 (August, 2013)
Part No. EM-WNAP-6350_v2.0 (2081-E10510-003)
III
CONTENTS
Chapter 1.Product Introduction........................................................................................................... 1
1.1
Package Contents ............................................................................................................... 1
1.2
Product Description............................................................................................................ 2
1.3
Product Features................................................................................................................. 6
1.4
Product Specifications ....................................................................................................... 7
Chapter 2.Hardware Installation ........................................................................................................10
2.1
Hardware Description .......................................................................................................10
2.1.1
The Bottom Panel ...................................................................................................10
Chapter 3.Connecting to the AP ........................................................................................................12
3.1
Preparation before Installation ........................................................................................12
3.1.1
Professional Installation Required ..........................................................................12
3.1.2
Safety Precautions..................................................................................................12
3.2
Installation Precautions....................................................................................................12
3.3
Installing the AP ................................................................................................................14
Chapter 4.Quick Installation Guide ...................................................................................................17
4.1
Manual Network Setup - TCP/IP Configuration ..............................................................17
4.1.1
4.2
Configuring the IP Address Manually .....................................................................17
Starting Setup in the Web UI ............................................................................................21
Chapter 5.Configuring the AP............................................................................................................23
5.1
Status..................................................................................................................................23
5.2
Easy Setup .........................................................................................................................26
5.3
Advanced ...........................................................................................................................27
5.3.1
Advanced - Management........................................................................................27
5.3.1.1.
Web Interface Settings (Password)................................................................................ 28
5.3.1.2.
Firmware Upgrade ......................................................................................................... 28
5.3.1.3.
Configuration.................................................................................................................. 29
5.3.1.4.
Load Factory Defaults .................................................................................................... 30
5.3.1.5.
Reboot System .............................................................................................................. 30
5.3.1.6.
Scheduling Reboot......................................................................................................... 31
5.3.2
Advanced – Advanced Settings..............................................................................31
5.3.2.1.
Time Zone Settings ........................................................................................................ 32
5.3.2.2.
DDNS Settings............................................................................................................... 32
5.3.2.3.
UPNP Settings ............................................................................................................... 34
5.3.2.4.
SNMP Settings............................................................................................................... 35
5.3.3
Advanced – Operation Mode..................................................................................36
5.3.3.1.
AP Router (AP+Router) ................................................................................................. 36
5.3.3.2.
AP Bridge (AP+WDS) .................................................................................................... 37
5.3.3.3.
Client Router (WISP) ..................................................................................................... 38
IV
5.3.3.4.
5.4
5.5
5.3.4
Advanced – System Log.........................................................................................43
5.3.5
Advanced – Tools ...................................................................................................44
5.3.5.1.
Ping................................................................................................................................ 44
5.3.5.2.
Traceroute...................................................................................................................... 45
5.3.5.3.
Throughput..................................................................................................................... 45
Firewall Settings................................................................................................................46
5.4.1
MAC/IP/Port Filtering ..............................................................................................46
5.4.2
Virtual Server ..........................................................................................................47
5.4.3
DMZ ........................................................................................................................48
5.4.4
Firewall....................................................................................................................49
5.4.5
QoS.........................................................................................................................50
5.4.6
Content Filtering .....................................................................................................51
5.4.6.1.
Webs URL Filter Settings ............................................................................................... 51
5.4.6.2.
Web Host Filter Settings ................................................................................................ 52
Network Settings...............................................................................................................52
5.5.1
Static (Fixed IP).............................................................................................................. 53
5.5.1.2.
Cable/Dynamic IP (DHCP)............................................................................................. 54
5.5.1.3.
PPPoE (ADSL)............................................................................................................... 54
5.5.1.4.
IPSEC ............................................................................................................................ 55
5.5.1.5.
PPTP ............................................................................................................................. 59
5.5.1.6.
L2TP .............................................................................................................................. 60
LAN .........................................................................................................................61
5.5.2.1.
DHCP Server ................................................................................................................. 62
5.5.2.2.
DHCP Relay................................................................................................................... 62
5.5.3
VLAN.......................................................................................................................63
5.5.4
Advanced Routing ..................................................................................................64
5.5.5
IPv6.........................................................................................................................65
Wireless Settings ..............................................................................................................66
5.6.1
5.7
WAN........................................................................................................................52
5.5.1.1.
5.5.2
5.6
Client Bridge (Slave AP Bridge) ..................................................................................... 43
Basic .......................................................................................................................66
5.6.1.1.
Wireless Mode – Access Point....................................................................................... 67
5.6.1.2.
Wireless Mode – WDS Access Point ............................................................................. 69
5.6.1.3.
Wireless Mode – WDS Repeater ................................................................................... 71
5.6.1.4.
Wireless Mode – WDS Client......................................................................................... 73
5.6.2
Profile Settings........................................................................................................75
5.6.3
Advanced................................................................................................................77
5.6.4
Access Control........................................................................................................78
Logout ................................................................................................................................79
Appendix A: FAQ.................................................................................................................................80
1.
What and how to find my PC’s IP and MAC address? ..................................................80
V
2.
What is Wireless LAN? .....................................................................................................80
3.
What are ISM bands?........................................................................................................80
4.
How does wireless networking work? ............................................................................80
5.
What is BSSID? .................................................................................................................81
6.
What is ESSID? .................................................................................................................81
7.
What are potential factors that may cause interference?.............................................81
8.
What are the Open System and Shared Key authentications? ....................................82
9.
What is WEP? ....................................................................................................................82
10.
What is Fragment Threshold? .........................................................................................82
11.
What is RTS (Request to Send) Threshold?...................................................................83
12.
What is Beacon Interval? .................................................................................................83
13.
What is Preamble Type?...................................................................................................83
14.
What is SSID Broadcast? .................................................................................................83
15.
What is Wi-Fi Protected Access (WPA)?.........................................................................84
16.
What is WPA2? ..................................................................................................................84
17.
What is 802.1x Authentication? .......................................................................................84
18.
What is Temporal Key Integrity Protocol (TKIP)? ..........................................................84
19.
What is Advanced Encryption Standard (AES)?............................................................84
20.
What is Inter-Access Point Protocol (IAPP)? .................................................................84
21.
What is Wireless Distribution System (WDS)? ..............................................................85
22.
What is Universal Plug and Play (UPnP)? ......................................................................85
23.
What is Maximum Transmission Unit (MTU) Size?........................................................85
24.
What is Clone MAC Address?..........................................................................................85
25.
What is DDNS? ..................................................................................................................85
26.
What is NTP Client? ..........................................................................................................85
27.
What is VPN?.....................................................................................................................85
28.
What is IPSEC? .................................................................................................................85
29.
What is WLAN Block Relay between Clients? ...............................................................86
30.
What is WMM?...................................................................................................................86
31.
What is WLAN ACK TIMEOUT? .......................................................................................86
32.
What is Modulation Coding Scheme (MCS)? .................................................................86
33.
What is Frame Aggregation? ...........................................................................................86
34.
What is Guard Intervals (GI)?...........................................................................................86
Appendix B: Configuring the PC in Windows 7 ...............................................................................87
Appendix C: Use Planet Smart Discovery to find AP ......................................................................90
Appendix D: Specifications................................................................................................................91
VI
User Manual of WNAP-6350
Chapter 1. Product Introduction
1.1 Package Contents
Thank you for choosing PLANET WNAP-6350. Before installing the AP, please verify the contents inside the
package box.
WNAP-6350 Wireless AP
Quick Installation Guide
CD-ROM
(User Manual included)
PoE Injector & Power Cord
Mounting Kit x 1
RJ-45 Waterproof Kit x 2
If there is any item missing or damaged, please contact the seller
immediately.
-1-
User Manual of WNAP-6350
1.2 Product Description
High Power Outdoor Wireless Coverage
PLANET Technology introduces the latest high power outdoor wireless LAN solution – the WNAP-6350
300Mbps PoE wireless outdoor AP. It provides higher transmit power, better performance, wide coverage
and more stable connection than standard wireless outdoor AP. As an IEEE 802.11b/g/n compliant wireless
device, the WNAP-6350 is able to give stable and efficient wireless performance for long distance application.
Adopting the IEEE 802.11n standard and 2T2R MIMO technology, the WNAP-6350 is able to deliver six times
faster data rate up to 300Mbps than the normal 802.11g wireless device. It also features adjustable output
power up to 800mW to extend broader coverage in outdoor long range application.
Wi-Fi City
Antenna
WNAP-6350
N
N
N
Antenna
Antenna
N
WNAP-6350
WNAP-6350
N
Antenna
WNAP-6350
N
Antenna
WNAP-6350
N
-2-
2.4GHz 802.11n
User Manual of WNAP-6350
Multiple Operating & Wireless Modes
The WNAP-6350 supports multiple types of wireless communication connectivities (AP, Client CPE, WDS PtP,
WDS PtMP, Repeater) meeting various application requirements and thus it gives users more comprehensive
experience when accessing through wireless LAN. It helps users to easily build a wireless network and extend
the wireless range of existing wireless network.
The WNAP-6350 also supports WISP mode, so CPE users can easily connect to Internet via WISP provider or
connect to a wired network.
WDS Repeater Mode
AP/Client Mode
WNAP-6350
WNAP-6350
WNAP-6350
Internet
Internet
N
N
N
N
Client
WAN
Antenna
Antenna
Antenna
Antenna
PoE
PoE
AP Mode
Client Mode
Switch
WDS Repeater Mode
Clients
WDS Bridge-PtP Mode
Clients
WNAP-6350
WNAP-6350
N
Clients
Clients
Antenna
N
Antenna
Antenna
N
N
Antenna
PoE
PoE
Bridge - PtP Mode
Switch
Switch
Wireless Internet
Service Provider
Clients
PoE
Clients
Bridge - PtMP Mode
Relay Mode
WNAP-6350
N
Switch
WNAP-6350
Switch
WISP Mode
Internet
PoE
Antenna
PoE
Switch
Clients
WDS Bridge-PtMP Mode
WNAP-6350
N
Switch
Antenna
Client
N
WNAP-6350
Antenna
N
N
Antenna
N
LAN
Antenna
WISP Mode
Bridge - Relay Mode
N
Antenna
Advanced Security and Management
In aspect of security, besides 64-/128-bit WEP encryption, the WNAP-6350 is integrated with WPA/WPA2,
WPA-PSK/WPA2-PSK and 802.1x authority to secure and protect your wireless LAN. The wireless MAC
filtering and SSID broadcast control consolidate the wireless network security and prevent unauthorized
wireless connection. To fulfill enterprise and various applications demand, the WNAP-6350 also provides
multiple SSIDs to enhance security and management.
Perfect Solution for Outdoor Environment
The WNAP-6350 is perfectly suitable for outdoor environments and exposed locations. With its IP67 aluminum
rugged strong housing, the WNAP-6350 can perform normally under rigorous weather conditions including
heavy rain, wind and snow. Moreover, the WNAP-6350 is rated to operate at the temperature from -30 to 75
degree C; thus, it can operate more stably than general outdoor equipment. It is the best way to use the
-3-
User Manual of WNAP-6350
WNAP-6350 to build outdoor wireless access applications between buildings on campuses, business, rural
areas and more.
Flexible Deployment with PoE Feature
Compliant with IEEE 802.3af/at Power over Ethernet standard, the WNAP-6350 can be powered by PSE
(Power Sourcing Equipment) via a single UTP cable. It thus reduces the needs of extra cables and dedicated
electrical outlets on the wall, ceiling or any other difficult-to-reach places. Furthermore, the WNAP-6350 is also
suitable for being integrated with PoE Solar Power System to offer farther wireless service in remote areas. It
enables the wireless LAN deployment to become more flexible in powering without the power outlet.
-4-
User Manual of WNAP-6350
Easy Installation and Management
With user-friendly Web UI and step by step Setup Wizard, the WNAP-6350 is easy to install, even for users
who never experience setting up a wireless network. Furthermore, with SNMP-based management interface,
the WNAP-6350 is convenient to be managed and configured remotely.
-5-
User Manual of WNAP-6350
1.3 Product Features






Industrial Compliant Wireless LAN & LAN

Compliant with IEEE 802.11n wireless technology capable of up to 300Mbps data rate

Backward compatible with 802.11b/g standard

Equipped with 10/100Mbps RJ-45 Ports for LAN & WAN, Auto MDI / MDI-X supported
Fixed-network Broadband Router

Supported connection types: Dynamic IP / Static IP / PPPoE / PPTP / L2TP / IPSec

Supports Virtual Server, DMZ for various networking applications

Supports DHCP Server, UPnP, Dynamic DNS
RF Interface Characteristics

Built-in two N-Type Female Antenna connectors

High Output Power up to 800mW with multiple adjustable transmit power control
Outdoor Environmental Characteristics

Aluminum Housing, IP67 Protection

IEEE 802.3af/at Power over Ethernet design

Operating Temperature: -30~75 degrees C
Multiple Operation & Wireless Mode

Multiple Operation Modes: Bridge, Gateway, WISP

Multiple Wireless Modes: AP, Client CPE (WISP), WDS PtP, WDS PtMP, Repeater

Supports Dual-SSID allowing users to access different networks through one single AP

Supports WMM (Wi-Fi Multimedia)
Secure Network Connection

Supports Software Wi-Fi Protected Setup (WPS)

Advanced security: 64/128-bit WEP, WPA / WPA2, WPA-PSK / WPA2-PSK (TKIP/AES), and
802.1x Authentication


Supports NAT firewall features with SPI function to protect against DoS attacks

Supports IP/Protocol-based access control and MAC filtering
Easy Installation & Management

Web-based UI and Quick Setup Wizard for easy configuration

Remote Management allows configuration from a remote site

SNMP-Based management interface

System status monitoring includes DHCP Client, System Log
-6-
User Manual of WNAP-6350
1.4 Product Specifications
Product
WNAP-6350
2.4GHz 300Mbps 802.11n Wireless Outdoor Access Point
Hardware Specifications
IEEE 802.11b/g/n Wireless LAN
IEEE 802.11i Wireless Security
Standard
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Ethernet
IEEE 802.3x Flow Control
IEEE 802.3af/at Power over Ethernet / PD
Memory
32 Mbytes DDR SDRAM
8 Mbytes Flash
Wireless IEEE 802.11b/g/n, 2T2R
Interface
LAN: 1 x 10/100Base-TX, Auto-MDI / MDIX, IEEE 802.3af/at PoE / PD port
WAN: 1 x 10/100Base-TX, Auto-MDI / MDIX
Antenna
N-Type Female connectors x 2
Wireless RF Specifications
Wireless Technology
IEEE 802.11b/g
IEEE 802.11n
IEEE 802.11b: 11, 5.5, 2 and 1Mbps
Data Rate
IEEE 802.11g: 54, 48, 36, 24, 18, 12, 9 and 6Mbps
IEEE 802.11n (20MHz): up to 150Mbps
IEEE 802.11n (40MHz): up to 300Mbp
Media Access Control
CSMA / CA
Modulation
Transmission/Emission Type: DSSS / OFDM
Data modulation type: OFDM with BPSK, QPSK, 16-QAM, 64-QAM,
DBPSK, DQPSK, CCK
Frequency Band
2.412GHz ~ 2.484GHz
Operating Channel
America/ FCC: 2.414~2.462GHz (11 Channels)
Europe/ ETSI: 2.412~2.472GHz (13 Channels)
Japan/ TELEC: 2.412~2.484GHz (14 Channels)
RF Output Power (Max.)
IEEE 802.11b/g: 29 ± 1.5dBm
IEEE 802.11n: 25 ± 1.5dBm
IEEE 802.11b: -95/ -94/ -92/ -90dBm (1/ 2/ 5.5/ 11Mbps)
Receiver Sensitivity
IEEE 802.11g: -90/ -82/ -80/ -75dBm (6/ 24/ 36/ 54Mbps)
IEEE 802.11n: -91/ -83/ -74/ -89/ -80/ -72dBm (MCS 0/ 3/ 6/ 9/ 12/ 15)
Output Power Control
3~29dBm
Software Features
LAN
Built-in DHCP server supporting static IP address distributing
Supports 802.1d STP (Spanning Tree)
 Static IP
WAN
 Dynamic IP
 PPPoE
-7-
User Manual of WNAP-6350
 PPTP
 L2TP
 IPSec
 Bridge
Operating Mode
 Gateway
 WISP
NAT firewall with SPI (Stateful Packet Inspection)
Firewall
Built-in NAT server supporting Virtual Server and DMZ
Built-in firewall with Port / IP address / MAC / URL filtering
 AP
 Client
Wireless Mode
 WDS PTP
 WDS PTMP
 WDS Repeater (AP+WDS)
Channel Width
Wireless Isolation
Encryption Type
20MHz / 40MHz
Enables isolation of each connected wireless client from communicating with
each other mutually.
64/128-bits WEP, WPA, WPA-PSK, WPA2, WPA2-PSK, 802.1X
Provides wireless LAN ACL (Access Control List) filtering
Wireless Security
Wireless MAC address filtering
Supports WPS (Wi-Fi Protected Setup )
Enable / Disable SSID Broadcast
Multiple SSID
Up to 2
Max. Wireless Client
40
Max. WDS AP
8
Max. Wired Client
60
WMM
Supports Wi-Fi Multimedia
QoS
Supports Quality of Service for bandwidth control
NTP
Network Time Management
Management
Web UI, DHCP Client, Configuration Backup & Restore, Dynamic DNS, SNMP
Diagnostic tool
System Log, Ping Watchdog
Mechanical & Power
IP Rate
IP67
Material
Aluminum
Dimensions (W x D x H)
320 x 27.5 x 320 mm
Weight
2.4kg
Installation
Pole mounting or Wall mounting
Power Requirements
Power Consumption
AP: IEEE 802.3af/at PoE / 48VDC input (PoE Injector included)
PoE Injector: 100~240VAC
7.68W
Environment & Certification
Operation Temperature
-30~75 degrees C
Operating Humidity
10~95% non-condensing
-8-
User Manual of WNAP-6350
Regulatory
CE / RoHS
Accessory
 48VDC IEEE 802.3af PoE injector & Power cord x 1
 Mounting Kit x 1
Standard Accessories
 Waterproof RJ-45 Connector Kit x 2
 Quick Installation Guide x 1
 CD (User’s Manual, Quick Installation Guide) x 1
-9-
User Manual of WNAP-6350
Chapter 2. Hardware Installation
Please follow the instructions below to connect the WNAP-6350 to the existing network devices and your
computers.
2.1 Hardware Description

Dimensions: 320 x 27.5 x 320 mm (W x D x H)
Figure 2-1 Three-way View
2.1.1 The Bottom Panel
The bottom panel provides the physical connectors connected to the power adapter and any other network
device. Figure 2-2 shows the bottom panel of the WNAP-6350.
-10-
User Manual of WNAP-6350
Bottom Panel
Figure 2-2 Bottom Panel
Interface
LAN
(802.3af/at PoE/PD port)
Description
10/100Mbps RJ-45 port , Auto MDI/ MDI-X & 802.3af/at PoE supported
Connect LAN port to the PoE injector or PoE switch to power on the
device.
N-Type Female Antenna Connectors.
N-Type (F)
Connect N-Type (F) Antenna Connectors with Outdoor Antenna through
the N-Type (Male) to N-Type (Male) RF cable.
10/100Mbps RJ-45 port , Auto MDI/ MDI-X
WAN / LAN
Connect this port to the xDSL modem in AP mode.
Connect this port to the network equipment in bridge mode.
Table 2-1 The Interface indication
-11-
User Manual of WNAP-6350
Chapter 3. Connecting to the AP
3.1 Preparation before Installation
3.1.1 Professional Installation Required
Please seek assistance from a professional installer who is well trained in the RF installation and knowledgeable
in the local regulations.
3.1.2 Safety Precautions
1.
To keep you safe and install the hardware properly, please read and follow these safety precautions.
2.
If you are installing the WNAP-6350 for the first time, for your safety as well as others’, please seek
assistance from a professional installer who has received safety training on the hazards involved.
3.
Keep safety as well as performance in mind when selecting your installation site, especially where there
are electric power and phone lines.
4.
When installing the WNAP-6350, please note the following things:

Do not use a metal ladder;

Do not work on a wet or windy day;

Wear shoes with rubber soles and heels, rubber gloves, long sleeved shirt or jacket.
5.
When the system is operational, avoid standing directly in front of it. Strong RF fields are present when the
transmitter is on.
3.2 Installation Precautions

Users MUST use a proper and well-installed surge arrestor and grounding kit with the WNAP-6350;
otherwise, a random lightning could easily cause fatal damage to the WNAP-6350. EMD (Lightning)
DAMAGE IS NOT COVERED UNDER WARRANTY.

Users MUST use the “Power cord and PoE Injector” shipped in the box with the WNAP-6350. Use of
other options will cause damage to the WNAP-6350.

Users MUST power off the WNAP-6350 first before connecting the external antennas to it; otherwise,
damage might be caused to the WNAP-6350 itself.
-12-
User Manual of WNAP-6350
OUTDOOR INSTALLATION WARNING
!
IMPORTANT SAFETY PRECAUTIONS:
LIVES MAY BE AT RISK! Carefully observe these instructions and any special instructions that are included with the
equipment you are installing.
CONTACTING POWER LINES CAN BE LETHAL. Make sure no power
lines are anywhere where possible contact can be made. Antennas, masts,
towers, guy wires or cables may lean or fall and contact these lines. People
may be injured or killed if they are touching or holding any part of
equipment when it contacts electric lines. Make sure there is NO possibility
that equipment or personnel can come in contact directly or indirectly with
power lines.
Assume all overhead lines are power lines.
The horizontal distance from a tower, mast or antenna to the nearest power line should be at least twice the total length of
the mast/antenna combination. This will ensure that the mast will not contact power if it falls either during installation or later.
TO AVOID FALLING, USE SAFE PROCEDURES WHEN WORKING AT HEIGHTS ABOVE GROUND.
 Select equipment locations that will allow safe, simple equipment installation.
 Don’t work alone. A friend or co-worker can save your life if an accident happens.
 Use approved non-conducting lasers and other safety equipment. Make sure all equipment is in good repair.
 If a tower or mast begins falling, don’t attempt to catch it. Stand back and let it fall.
 If anything such as a wire or mast does come in contact with a power line, DON’T TOUCH IT OR ATTEMPT TO
MOVE IT. Instead, save your life by calling the power company.
 Don’t attempt to erect antennas or towers on windy days.
MAKE SURE ALL TOWERS AND MASTS ARE SECURELY GROUNDED, AND ELECTRICAL CABLES CONNECTED TO
ANTENNAS HAVE LIGHTNING ARRESTORS. This will help prevent fire damage or human injury in case of lightning, static
build-up, or short circuit within equipment connected to the antenna.
 The base of the antenna mast or tower must be connected directly to the building protective ground or to one or more
approved grounding rods, using 10 AWG ground wire and corrosion-resistant connectors.
 Refer to the National Electrical Code for grounding details.
IF A PERSON COMES IN CONTACT WITH ELECTRICAL POWER, AND CANNOT MOVE:

DON’T TOUCH THAT PERSON, OR YOU MAY BE ELECTROCUTED.

Use a non-conductive dry board, stick or rope to push or drag them so they no longer are in contact with electrical
power.
Once they are no longer contacting electrical power, administer CPR if you are certified, and make sure that emergency
medical aid has been requested.
-13-
User Manual of WNAP-6350
3.3 Installing the AP
Please install the AP according to the following steps. Don't forget to pull out the power plug and keep your
hands dry.
Step 1. Plug the N-Type (M) to N-Type (M) RF cables into the antenna connectors of the WNAP-6350, and
then connect the N-Type (F) antennas to the other side of the RF cables.
Figure 3-1
Step 2. Plug the RJ-45 Ethernet cable into the LAN Port of WNAP-6350 through the waterproof kit.
Figure 3-2
Step 3. Take out the power cord and PoE injector, plug the power cord into the DC port and plug the other side
of the RJ-45 cable into the POE port of the PoE injector.
Figure 3-3
-14-
User Manual of WNAP-6350
Step 4. Plug the other waterproof kit into the WAN/LAN port to complete the installation.
Figure 3-4
Step 4a. Pole Mounting:
(a.1) Attach the mounting bracket to the back of the device by using four screws and flat washers.
(a.2) Assemble the M bracket on the outside of the mounting bracket by using four screws and flat washers.
(a.3)Install the antenna assembly against the pole by using the teeth bracket, and then tighten it by four long
screws.
Figure 3-5
※ Pole diameter less than 5cm may require the use of hex nuts to lock the long screws to
the suitable location.
-15-
User Manual of WNAP-6350
Step 4b. Wall Mounting:
(b.1) Attach the mounting bracket to the back of the device by using four screws and flat washers.
(b.2) Assemble the M bracket on the wall by using four screws and flat washers.
(b.3) Install the mounting bracket assembly inside the M bracket mounted in the wall by using four screws and
flat washers.
Figure 3-6
Step 5. Connect the power cord to the power socket on the PoE injector, and the other end into an electrical
outlet. Then power on the AP.
-16-
User Manual of WNAP-6350
Chapter 4. Quick Installation Guide
This chapter will show you how to configure the basic functions of your Wireless AP using Easy Setup within
minutes.
A computer with wired Ethernet connection to the Wireless AP is required for the first-time
configuration.
4.1 Manual Network Setup - TCP/IP Configuration
The default IP address of the WNAP-6350 is 192.168.1.1. And the default Subnet Mask is 255.255.255.0. These
values can be changed as you desire. In this guide, we use all the default values for description.
Connect the WNAP-6350 with your PC by an Ethernet cable plugging in the LAN port of the PoE injector on one
side and in the LAN port of the PC on the other side. Please power on the WNAP-6350 by PoE from PoE injector
or PoE switch.
In the following sections, we’ll introduce how to install and configure the TCP/IP correctly in Windows XP. And
the procedures in other operating systems are similar. First, make sure your Ethernet adapter is working, and
refer to the Ethernet adapter’s manual if needed.
4.1.1 Configuring the IP Address Manually
Summary:

Set up the TCP/IP Protocol for your PC.

Configure the network parameters. The IP address is 192.168.1.xxx ("xxx" is any number from 2 to
254), Subnet Mask is 255.255.255.0, and Gateway is 192.168.1.1 (The AP's default IP address)
1
Select Use the following IP address radio button.
2
If the AP's LAN IP address is 192.168.1.1, enter IP address 192.168.1.x (x is from 2 to 254), and Subnet
mask 255.255.255.0.
3
Select Use the following DNS server addresses radio button. In the Preferred DNS Server field, you can
enter the DNS server IP address which has been provided by your ISP
-17-
User Manual of WNAP-6350
Figure 4-1
Now click OK to save your settings.
Now, you can run the Ping command in the command prompt to verify the network connection between your
PC and the AP. The following example is in Windows XP OS. Please follow the steps below:
1.
Click on Start > Run.
-18-
User Manual of WNAP-6350
Figure 4-2
2.
In the run box type “cmd” and click OK. (Windows Vista users type “cmd” in the Start .Search box.)At the
prompt.
Figure 4-3
Open a command prompt, and type ping 192.168.1.1, and then press Enter.
If the result displayed is similar to Figure 4-4, it means the connection between your PC and the AP
has been established well.
-19-
User Manual of WNAP-6350
Figure 4-4 Success result of Ping command
If the result displayed is similar to Figure 4-5, it means the connection between your PC and the AP
has failed.
Figure 4-5 Failure result of Ping command
If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your AP. Some
firewall software programs may block a DHCP request on newly installed adapters.
-20-
User Manual of WNAP-6350
4.2 Starting Setup in the Web UI
It is easy to configure and manage the WNAP-6350 with the web browser.
Step 1.
To access the configuration page, open a web-browser and enter the default IP address
http://192.168.1.1 in the web address field of the browser.
Figure 4-6 Login the AP
After a moment, a login window will appear. Enter admin for the User Name and Password, both in lower case
letters. Then click the OK button or press the Enter key.
Figure 4-7 Login Window
Default IP Address: 192.168.1.1
Default User name: admin
Default Password: admin
If the above screen does not pop up, it may mean that your web-browser has been set to a
proxy. Go to Tools menu>Internet Options>Connections>LAN Settings, in the screen
that appears, cancel the Using Proxy checkbox, and click OK to finish it.
-21-
User Manual of WNAP-6350
After entering the username and password, the Status page screen appears as Figure 4-8
Figure 4-8 WNAP-6350 Web UI Screenshot
Step 2.
Go to “Easy Setup” to choose an Operation Mode. Please refer to the instructions in the next chapter
for configuring the other Operation Modes.
Figure 4-9 Choose Operation Mode
Step 3.
Please enter the SSID, configure your Encryption Settings, Pre-Shared Key, etc. Then click Done
button to make the configuration take effect immediately.
Figure 4-10 Configure Wireless Settings
-22-
User Manual of WNAP-6350
Chapter 5. Configuring the AP
This chapter delivers a detailed presentation of AP’s functionalities and features under 3 main menus (Status,
Easy Setup, and Advanced) below, allowing you to manage the AP with ease.
Figure 5-1
5.1 Status
On this page, you can view information about the current running status of the WNAP-6350, including WAN
interface, LAN interface, wireless interface, and firmware version information.

Status
This section allows you to view the AP’s system info listed below:
Figure 5-1-1
-23-
User Manual of WNAP-6350
Object
Description
Internet Configuration
 Connected Type
Displays current Internet connection type.
 Disconnected: Indicates that the Ethernet cable from your
ISP side is / is not correctly connected to the WAN port on
the AP or the AP is not logically connected to your ISP.
 Connected Status
 Connecting: Indicates that the WAN port is correctly
connected and is requesting an IP address from your ISP.
 Connected: Indicates that the AP has been connected to
your ISP.
 WAN IP
Displays WAN IP address.
 Subnet Mask
Displays WAN subnet mask.
 Default Gateway
Displays WAN gateway address.
 Primary Domain Name
Server
 Secondary Domain
Name Server
 MAC Address
Displays WAN DNS address.
Displays WAN DNS address.
Displays AP’s WAN MAC address.
LAN Configuration
 LAN IP Address
Displays LAN IP address.
 LAN Netmask
Displays LAN subnet mask.
 MAC Address
Displays AP’s LAN MAC address.
System Info

 Firmware Version
Displays current F/W version.
 System Time
Displays the System Time.
 Operation Mode
Displays current Operation Mode.
 Wireless MAC Address
Displays AP’s Wireless MAC address.
Statistics
This section allows you to view the AP’s statistics listed below:
-24-
User Manual of WNAP-6350
Figure 5-1-2
Object
Description
Memory
 Memory Left/
Memory Total
Displays the retain memory and total memory.
WAN/LAN

 WAN Rx packets
Displays the real-time packets received from WAN port.
 WAN Rx bytes
Displays the real-time bytes received from WAN port.
 WAN Tx packets
Displays the real-time packets transmitted from WAN port.
 WAN Tx bytes
Displays the real-time bytes transmitted from WAN port.
 LAN Rx packets
Displays the real-time packets received from LAN port.
 LAN Rx bytes
Displays the real-time bytes received from LAN port.
 LAN Tx packets
Displays the real-time packets transmitted from LAN port.
 LAN Tx bytes
Displays the real-time bytes transmitted from LAN port.
DHCP Clients
This section displays a DHCP dynamic client list, which includes MAC address, IP address, and lease time info.
-25-
User Manual of WNAP-6350
Figure 5-1-3
Object
Description
 MAC address
Displays MAC address of a given host.
 IP Address
 Expires in

Displays IP address(es) that client(s) obtained from the DHCP
server.
Remaining time for a corresponding IP address lease.
Station List
This section allows you to view the Station List. The Station List submenu is only available in AP mode.
Figure 5-1-4
Object
Description
 MAC address
Displays MAC address of a connected client.
 Rate
Displays connection speed of a connected client.
 Expires in
Displays the signal strength of a connected client.
5.2 Easy Setup
The Easy Setup helps you configure the basic functions of your Wireless AP within minutes.
Please refer to the Step 2 in the section “4.2 Starting Setup in the Web UI” for the detailed procedure.
Figure 5-2-1
-26-
User Manual of WNAP-6350
5.3 Advanced
“Advanced” includes the following four submenus (Advanced, Firewall Settings, Network Settings, and Wireless
Settings). Clicking any of them enters corresponding interface for configuration. Below explains, in details, each
such feature.
Figure 5-3-1
5.3.1 Advanced - Management
This section allows you to manage the Wireless AP.
-27-
User Manual of WNAP-6350
5.3.1.1. Web Interface Settings (Password)
Figure 5-3-2
Object
Description
 User Name
Display the User Name info.
 Password
Enter the new password that you prefer for login.
 Re-enter to confirm
Re-enter the new password to confirm.
If you change the login password, you must enter the new one in the next login.
5.3.1.2. Firmware Upgrade
Figure 5-3-3
-28-
User Manual of WNAP-6350
Click the “Browse…” button to select the new firmware for upgrading.
Object
Description
 Software Version
Display the current Software Version info.
 Location
Click the “Browse…” button to select the new firmware in this field.
 Upload
Click the “Upload” button to upgrade the new firmware.
!
IMPORTANT SAFETY PRECAUTIONS:
Do Not Turn off the power or close the browser during upgrade process!
5.3.1.3. Configuration
Figure 5-3-4
Click the “Export” button to back up the configuration of the Wireless AP, and click “Import” to restore the
configuration.
Object
Description
 Export
Click the “Export” button to back up the configuration.
 Browse…
 Import
Click the “Browse…” button to select the configuration file in this
field for restoring settings.
Click the “Import” button to restore the configuration.
-29-
User Manual of WNAP-6350
5.3.1.4. Load Factory Defaults
Figure 5-3-5
Click the “Load Default” button to reset it to factory default settings.
5.3.1.5. Reboot System
Figure 5-3-6
Click the “Reboot Now!” button to restart the Wireless AP.
-30-
User Manual of WNAP-6350
5.3.1.6. Scheduling Reboot
Figure 5-3-7
Select “Enable” to configure the system auto reboot according to the Duration Time (Time interval).
Object
Description
 Enable Scheduling
Enable: select it to enable the Scheduling Reboot.
Reboot
 Duration Time
(hh:mm)
Disable: select it to disable the Scheduling Reboot.
Configure the particular time interval for the system auto reboot.
hh: means hours
mm: means minutes
5.3.2 Advanced – Advanced Settings
This section allows you to configure advanced settings of the Wireless AP.
-31-
User Manual of WNAP-6350
5.3.2.1. Time Zone Settings
Figure 5-3-8
The page includes the following fields:
Object
Description
 Current Time
Display the current time.
 Sync with host
Click it to sync your PC’s time to the device.
 Time Zone
Select your current time zone.
 SNTP Server
Configure your SNTP Server.
 SNTP Synchronization
Determines a time length when device periodically updates its
(minutes)
time and date info from Internet.
5.3.2.2. DDNS Settings
Figure 5-3-9
The page includes the following fields:
Object
Description
-32-
User Manual of WNAP-6350
 Dynamic DNS Provider
 Host Name
Select your Dynamic DNS Provider.
Enter the host name or domain name provided by your DDNS
service provider.
 User Name
Enter the name of your DDNS account.
 Password
Password: Enter the password of the DDNS account.
Example of Planet DDNS Settings:
Please go to http://www.planetddns.com/ to register a Planet DDNS account.
Please refer to the FAQ (http://www.planetddns.com/index.php/faq) for how to register a free account.
Please refer to the procedure listed as follows to configure using Planet DDNS service.
Step 1. Select “planetddns.com” to choose Planet DDNS service.
Step 2. Configure the DDNS account that has been registered on Planet DDNS website.
Host Name: Enter your DDNS host (format: xxx.planetddns.com, xxx is the registered domain name)
User Name: Enter your DDNS account
Password: Enter your DDNS account’s password
Figure 5-3-10
Step 3. Go to “Advanced-> Firewall Settings-> Firewall” to allow remote access from WAN port.
Figure 5-3-11
Step 4. Go to “Advanced-> Network Settings-> WAN” to configure WAN Connection using Static (Fixed IP).
-33-
User Manual of WNAP-6350
Figure 5-3-12
Step 5. Apply the settings, and connect your WAN port of the Wireless AP to the internet by Ethernet cable.
Step 6.
In a remote computer, enter the DDNS host name as the figure is shown below. Then, you should be
able to login the WNAP-6350 remotely.
Please remember to enter the remote management port number that you have configured in Step 3.
Figure 5-3-13
You can go to My Devices page of Planet DDNS website to check if the “Last Connection IP” is displayed.
This indicates your DDNS service is working properly.
Figure 5-3-14
5.3.2.3. UPNP Settings
Select “Enable” to enable the UPNP function.
-34-
User Manual of WNAP-6350
Figure 5-3-15
In the computer connected with the WNAP-6350, go to “Network” to check whether the WNAP-6350 is
displayed on the list.
Double-click it to logon the Web UI of the WNAP-6350.
Figure 5-3-16
5.3.2.4. SNMP Settings
Enabling SNMP function will allow the network management station to retrieve statistics and status from the
SNMP Agent in the device.
-35-
User Manual of WNAP-6350
Figure 5-3-17
The page includes the following fields:
Object
Description
Choose Enable to open this function if you want to have
 SNMP Settings
remote control through SNMPv1/v2 agent.
Choose Disable to close this function.
Enter the community name that allows Read-Only access to
 Get Community
the Device's SNMP information. The community name can be
considered a group password. The default setting is public.
Enter the community name that allows Read/Write access to
 Set Community
the Device's SNMP information. The community name can be
considered a group password. The default setting is private.
5.3.3 Advanced – Operation Mode
There are 4 operation modes (AP Router, AP Bridge, Client Router, Client Bridge) that can be configured to
meet various applications.
5.3.3.1. AP Router (AP+Router)
In the Access Point Mode with Router Function, the WNAP-6350 acts as a central connection point, which
wireless clients can connect to. The DHCP & NAT is enabled, so the clients are wirelessly connected to the
WNAP-6350 that can share the internet connection by connecting the WNAP-6350 to a DSL/cable modem.
-36-
User Manual of WNAP-6350
1. Connect the LAN port of the WNAP-6350 to the POE port of the PoE Injector over an Ethernet cable.
2. Connect the DSL/cable modem to the WAN port of the WNAP-6350.
3. Plug one end of the power cord into the PoE Injector, and the other end in electrical socket.
4. Go to “Advanced-> Operation Mode” to configure it in AP Router Mode.
Figure 5-3-18
In this mode, the LAN2 of the WNAP-6350 works as the WAN port.
To configure the Wireless Settings of AP Router Mode, please refer to the section 5.6 Wireless Settings.
5.3.3.2. AP Bridge (AP+WDS)
In the Access Point mode with WDS function, the WNAP-6350 functions like a central connection for any
stations or clients. Stations and clients must configure the same SSID and Security Password to associate within
the range. The WNAP-6350 supports 2 different SSIDs to separate different clients at the same time.
-37-
User Manual of WNAP-6350
1. Connect the LAN port of the WNAP-6350 to the POE port of the PoE Injector over an Ethernet cable.
2. Connect the PC to the LAN port of the PoE Injector over an Ethernet cable.
3. Plug one end of the power cord into the PoE Injector, and the other end in electrical socket.
4. Go to “Advanced-> Operation Mode” to configure it to AP Bridge mode.
Figure 5-3-19
In this mode, the wireless interface of the WNAP-6350 works as the WAN port.
To configure the Wireless Settings of AP Bridge Mode, please refer to the section 5.6 Wireless Settings.
5.3.3.3. Client Router (WISP)
In the Client Router mode, the WNAP-6350 has DHCP Server build inside that allows many LANs automatically
generate an IP address to share the same Internet. Connect an AP/WISP wirelessly and connect to LANs via
wired. The Client Router mode acts completely opposite to the AP Router mode.
-38-
User Manual of WNAP-6350
1. Connect the LAN port of WNAP-6350 to the POE port of the PoE Injector over an Ethernet cable.
2. Connect the PC to the LAN port of the PoE Injector over an Ethernet cable.
3. Plug one end of the power cord into the PoE Injector, and the other end in electrical socket.
4. Go to “Advanced-> Operation Mode” to configure it to Client Router mode.
Figure 5-3-20
WISP Setup Procedure:
Step 1. Go to Advanced-> Wireless Settings-> Profile Settings.
-39-
User Manual of WNAP-6350
Figure 5-3-21
Step 2. Click “Site Survey” to discover the Wireless Internet Service Provider.
Step 3. Select the WISP’s AP, and the click “Select”.
Figure 5-3-22
Step 4. Enter the Passphrase, and then click “Add” to add this setting to the profile.
-40-
User Manual of WNAP-6350
Figure 5-3-23
Step 5. The profile should be listed on the Profile List as the figure is shown below.
Figure 5-3-24
Step 6. Go to “Advanced-> Network Settings-> LAN” to enable DHCP Server.
-41-
User Manual of WNAP-6350
Figure 5-3-25
Step 7. Go to “Advanced-> Network Settings-> WAN” to configure the WAN Connection.
Figure 5-3-26
Step 8. Configure the wired client’s TCP/IP setting to “Obtain an IP address automatically”.
Figure 5-3-27
-42-
User Manual of WNAP-6350
After getting the IP assigned by the WNAP-6350, ping the DNS server to check whether internet connection is
reachable.
5.3.3.4. Client Bridge (Slave AP Bridge)
In the Client Bridge mode, the WNAP-6350 functions like a wireless adapter. Connect to an Access Point
wirelessly and surf Internet whenever you want. Using Site Survey to scan all the Access Points within the range
and configure its SSID and Security Password to associate with it.
1. Connect the LAN port of WNAP-6350 to the POE port of the PoE Injector over an Ethernet cable.
2. Connect the PC to the LAN port of the PoE Injector over an Ethernet cable.
3. Plug one end of the power cord into the PoE Injector, and the other end in electrical socket.
4. Go to “Advanced-> Operation Mode” to configure it to Client Bridge mode.
Figure 5-3-28
To configure the Wireless Settings of Client Bridge Mode, please refer to the section 5.6 Wireless Settings.
5.3.4 Advanced – System Log
Choose menu “Advanced-> System Log” to view the logs of the Wireless AP.
-43-
User Manual of WNAP-6350
Click “Refresh” to update the system log.
Click “Clear” to erase the current system log.
Figure 5-3-29
5.3.5 Advanced – Tools
The Tools included Ping, Traceroute, and Throughput can help user diagnostic the network connection.
5.3.5.1. Ping
Ping is a network tool used to test whether a particular host is reachable across an IP network.
Enter the IP, Ping Count, and click “Start” to diagnostic your internet connection.
Figure 5-3-30
-44-
User Manual of WNAP-6350
5.3.5.2. Traceroute
Traceroute is a computer network diagnostic tool for displaying the route (path) and measuring transit delays of
packets across an Internet Protocol (IP) network. It can help identify connection problems.
Enter the IP or Host Name, and click “Start” to diagnostic your internet connection.
Figure 5-3-31
5.3.5.3. Throughput
Click “VISIT THE SITE TO TEST SPEED” button to go to http://www.speedtest.net/ to test the Internet
connection speed.
Figure 5-3-32
-45-
User Manual of WNAP-6350
5.4 Firewall Settings
5.4.1 MAC/IP/Port Filtering
Figure 5-4-1
The page includes the following fields:
Object
Description
 MAC/IP/Port Filtering
Select Enable to enable the MAC/IP/Port Filtering function.
 Default Policy
Select a policy for filtering rule.
 MAC Address
 Destination IP address
(DIP)
 Source IP address
Fill in the MAC address of source NIC, to restrict data
transmission.
Fill in the IP address of destination, to restrict data
transmission.
Fill in the IP address of source, to restrict data transmission.
-46-
User Manual of WNAP-6350
(SIP)
 Protocol
 Destination Port Range
 Source Port Range
Select the protocol that you want to restrict. There are four
options: None, TCP, UDP and ICMP.
Fill in the start-port and end-port number of destination, to
restrict data transmission.
Fill in the start-port and end-port number of source, to restrict
data transmission.
 Action
Select Accept or Drop to specify the action of filtering policies.
 Comment
Make a comment for the filtering policy.
5.4.2 Virtual Server
Figure 5-4-2
-47-
User Manual of WNAP-6350
The page includes the following fields:
Object
Description
 Virtual Server
Select Enable to enable the Virtual Server function.
To forward data packets coming from WAN to a specific IP
 IP address
address that hosted in local network behind the NAT firewall, fill
in the IP address.
To forward data packets coming from WAN to a specific IP
 Private Port
address that hosted in local network behind the NAT firewall, fill
in the private port.
To forward data packets coming from WAN to a specific IP
 Public Port
address that hosted in local network behind the NAT firewall, fill
in the public port.
 Protocol
 Comment
The protocol used for this application, either TCP, UDP, or
TCP&UDP (all protocols are supported by the Device.).
Make a comment to help identify the setting.
5.4.3 DMZ
Figure 5-4-3
The page includes the following fields:
Object
Description
 DMZ Settings
Select Enable to enable the DMZ function.
 DMZ IP Address
To support DMZ in your firewall design, fill in the IP address of
DMZ host that can be accessed from the WAN interface.
-48-
User Manual of WNAP-6350
5.4.4 Firewall
Figure 5-4-4
The page includes the following fields:
Object
 Remote Management
(via WAN)
 Remote Management
Port
Description
Select Deny or Allow for remote management function.
Configure the port for remote management.
 Ping from WAN Filter
Select Deny or Allow for Ping permit from WAN.
 SPI Firewall
Select Disable or Enable for SPI firewall function.
Enable it to let the LAN devices connect to the Internet.
All computers must be assigned with a public IP address to get
 Network Address
Translation
connected to the Internet without NAT. However, Internet Service
Providers only provide very few IP addresses to every user.
Therefore it is necessary to use NAT to share a single public IP
address to multiple computers on local network, so everyone can get
connected to the Internet.
 PPPoE Passthrough
Enable it to allow Multiple PPP connections on remote hosts.
-49-
User Manual of WNAP-6350
5.4.5 QoS
Quality of Service provides an efficient way for clients on the network to share the bandwidth with a promised
quality of Internet service. Without QoS, all computers and devices on the network will compete with each other
to get the bandwidth, and some applications which require guaranteed bandwidth (like video streaming and
network telephone) will be affected. With this function, you can limit the maximum bandwidth or give a
guaranteed bandwidth for a specific computer, to avoid such unpleasing result from happening.
Figure 5-4-5
The page includes the following fields:
Object
Description
 QoS Setup
Select Enable to enable the QoS function.
 Upload Bandwidth
Set the limit of total upload bandwidth in kbits. To disable
upload bandwidth limitation, input ‘0’ here.
-50-
User Manual of WNAP-6350
 Download Bandwidth
 Target
Set the limit of total download bandwidth in kbits. To disable
download bandwidth limitation, input ‘0’ here.
Set the target of QoS rule.
Specify the local (source) IP address that will be affected by
this rule. Please input the starting IP address in the left field,
 Source IP
and input the end IP address in the right field to define a range
of IP addresses, or just input the IP address in the left field to
define a single IP address.
Specify the remote (destination) IP address that will be affected
by this rule. Please input the starting IP address in the left field,
 Destination IP
and input the end IP address in the right field to define a range
of IP addresses, or just input the IP address in the left field to
define a single IP address.
 Application
Select the pre-defined application for this rule.
Please select the protocol type of this rule. If you don’t know
 Protocol
what protocol your application uses, please try ‘TCP’ first, and
switch to ‘UDP’ if this rule doesn’t seems to work.
 Ports
Fill out the ports for this rule.
 Number of Bytes
Fill out the maximum number of bytes for this rule.
5.4.6 Content Filtering
There are two types (Webs URL Filter Settings and Web Host Filter Settings) of content filtering.
5.4.6.1. Webs URL Filter Settings
The Webs URL Filter option allows you to set up a list of Web sites you would like to deny through your network.
Please enter a URL for filtering.
-51-
User Manual of WNAP-6350
Figure 5-4-6
5.4.6.2. Web Host Filter Settings
The Web Host Filter option allows you to set up a list of keywords you would like to deny through your network.
Please enter a Host (keyword) for filtering.
Figure 5-4-7
5.5 Network Settings
5.5.1 WAN
There are 5 submenus under the Network menu: WAN, LAN, VLAN, Advanced Routing and IPv6. Click any of
them, and you will be able to configure the corresponding function.
-52-
User Manual of WNAP-6350
WAN Connection Types:
5.5.1.1. Static (Fixed IP)
If your ISP provides a static or fixed IP Address, Subnet Mask, Gateway and DNS setting, select Static
(Fixed IP). The Static IP settings page will appear as the figure is shown below.
Figure 5-5-1
The page includes the following fields:
Object
Description
 WAN Connections
Select Static (Fixed IP) from the list.
 IP Address
 Subnet Mask
 Default Gateway
 Primary DNS Server
 Secondary DNS Server
Enter the IP address in dotted-decimal notation provided by
your ISP.
Enter the subnet Mask in dotted-decimal notation provided by
your ISP, usually is 255.255.255.0
(Optional) Enter the gateway IP address in dotted-decimal
notation provided by your ISP.
(Optional) Enter the DNS IP address in dotted-decimal notation
provided by your ISP.
(Optional) Enter another DNS IP address in dotted-decimal
notation provided by your ISP.
-53-
User Manual of WNAP-6350
5.5.1.2. Cable/Dynamic IP (DHCP)
If your ISP provides the DHCP service, please choose Cable/Dynamic IP (DHCP) type, and the AP Router will
automatically obtain IP parameters from your ISP. You can see the page as shown below.
Figure 5-5-2
The page includes the following fields:
Object
Description
 WAN Connections
Select Cable/Dynamic IP (DHCP) from the list.
 Host Name
This option specifies the Host Name of the AP Router.
 Primary DNS Server
 Secondary DNS Server
(Optional) Enter the DNS IP address in dotted-decimal notation
provided by your ISP.
(Optional) Enter another DNS IP address in dotted-decimal
notation provided by your ISP.
5.5.1.3. PPPoE (ADSL)
If local ISP provides a PPPoE connection, choose PPPoE (ADSL) and fill the necessary parameters below.
-54-
User Manual of WNAP-6350
Figure 5-5-3
The page includes the following fields:
Object
Description
 WAN Connections
Select PPPoE (ADSL) from the list.
 Host Name
This option specifies the Host Name of the AP Router.
 User Name / Password
Enter the User Name and Password provided by your ISP.
These fields are case-sensitive.
 Verify Password
Enter the same password entered above for the confirmation.
 Operation Mode
Keep Alive: Being constantly connected.
 Keep Alive Mode
 MTU
 Primary DNS Server
 Secondary DNS Server
Set up the redial period after the disconnection.
The default setting is "60 seconds".
Please input the MTU value of your network connection here. If
you don’t know, please keep the default value.
(Optional) Enter the DNS IP address in dotted-decimal notation
provided by your ISP.
(Optional) Enter another DNS IP address in dotted-decimal
notation provided by your ISP.
5.5.1.4. IPSEC
If your ISP provides IPSEC connection, please select IPSEC. And enter the following parameters.
-55-
User Manual of WNAP-6350
Figure 5-5-4
Figure 5-5-5
The page includes the following fields:
Object
Description
 WAN Connections
Select IPSEC from the list.
 Primary DNS Server
 Secondary DNS Server
(Optional) Enter the DNS IP address in dotted-decimal notation provided
by your ISP.
(Optional) Enter another DNS IP address in dotted-decimal notation
provided by your ISP.
-56-
User Manual of WNAP-6350
 Connection address
family
 IPSec Operation Mode
For an IPSec connection, all host addresses must be of the same
Address Family (IPv4 and IPv6 use different Address Families).
Select the IPSec Operation mode from the drop-down list.
This field allows you to set the connection type to any of the following:
Select Tunnel to specify a Host to Host, Host to Subnet (Road
Warrior), or Subnet to Subnet Tunnel. This is by far the most common
connection type.
Select Transport to specify a Host to Host Transport mode tunnel. This
connection type is much less common, and would generally only be used
if you are attempting to establish and IPSec connection to another host
which specifically requires this mode.
 IPSec Connection Type
Select Passthrough to disable IPSec processing on packets associated
with the tunnel. We can't imagine a scenario where you would use this
connection type. I mean seriously, if you don't allow IPSec to process the
packets then you don't really have a tunnel, right? Still, the underlying
protocol supports this mode, and so here we are.
Select Drop to cause the kernel to drop IPSec packets associated with
the tunnel.
Select Reject to cause the kernel to reject IPSec packets associated with
the tunnel.
Perfect Forward Secrecy (PFS)—PFS ensures that a given IPSec SA
key was not derived from any other secret, like some other keys. In other
words, if someone breaks a key, PFS ensures that the attacker is not
able to derive any other key. If PFS is not enabled, someone can
potentially break the IKE SA secret key, copy all the IPSec protected
data, and then use knowledge of the IKE SA secret in order to
compromise the IPSec SAs setup by this IKE SA. With PFS, breaking
 PFS|DH Group
IKE does not give an attacker immediate access to IPSec. The attacker
needs to break each IPSec SA individually.
Diffie-Hellman (DH) key exchange protocol allows two parties without any
initial shared secret to create one securely. The following Modular
Exponential (MODP) and Elliptic Curve (EC2N) Diffie-Hellman (also
known as "Oakley") Groups are supported:
Diffie-Hellman Group
Name
Reference
Group 1
768 bit MODP group
RFC 2409
-57-
User Manual of WNAP-6350
 IPSec Authentication
Group 2
1024 bits MODP group
RFC 2409
Group 3
EC2N group on GP(2^155)
RFC 2409
Group 4
EC2N group on GP(2^185)
RFC 2409
Group 5
1536 bits MODP group
RFC 3526
The AP supports SHA1 & MD5 authentication algorithms.
The AP supports DES, 3DES, AES, Blowfish, Twofish, Camellia
Encryption methods.
DES - 56-bit DES-CBC encryption algorithm
3DES - 168-bit DES encryption algorithm
 IPSec Encryption
AES - 128, 192 and 256-bit key AES-CBC encryption algorithm
Blowfish - a symmetric block cipher that can be used as a drop-in
replacement for DES or IDEA. It takes a variable-length key, from 32 bits
to 448 bits.
Twofish - Twofish has a 128-bit block size, a key size ranging from 128 to
256 bits, and is optimized for 32-bit CPUs.
Camellia - 128, 192 and 256-bit key Camellia encryption algorithm
 SA connection Life
Time
 IKE Key Tries
 Local IP Address
 Peer IP Address
 Local Subnet
 Peer Subnet
 Local Gateway
 Peer Gateway
 IPSec Tunnel Name
This value describes the timeframe in hours for which the IKE SA is valid
and when the next rekeying should take place.
The field is used to specify the retry times of IKE Key.
This field is used to configure the IP address of the Untangle server on
the network configured in the Local Network field.
This field should contain the public IP address of the host to which the
IPSec VPN will be connected.
This field is used to configure the local network that will be reachable
from hosts on the other side of the IPSec VPN.
This field is used to configure the remote network that will be reachable
from hosts on the local side of the IPSec VPN.
This field is used to configure the Gateway of the Untangle server on the
network configured in the Local Network field.
This field should contain the public Gateway of the host to which the
IPSec VPN will be connected.
This field should contain a short name or description.
This field should contain the shared secret or PSK (pre-shared key) that
is used to authenticate the connection, and must be the same on both
 IPSec Secret Key
sides of the tunnel for the connection to be successful. Because the PSK
is actually used as the encryption key for the session, using long strings
of a random nature will provide the highest level of security.
-58-
User Manual of WNAP-6350
Lifetime settings determine when a new key is generated. Any time a key
lifetime is reached, the associated SA is also renegotiated. The process
of generating new keys at intervals is called dynamic rekeying or key
 IPSec Key Life time
regeneration. Lifetimes allow you to force the generation of a new key
after a specific interval. For example, if the communication takes 12
hours and you specify the key lifetime as 1 hour, 12 keys will be
generated (one every 1 hour) during the exchange.
NAT Traversal also known as UDP encapsulation allows traffic to get to
 NAT Traversal
the specified destination when a device does not have a public address.
This is usually the case if your ISP is doing NAT, or the external interface
of your firewall is connected to a device that has NAT enabled.
 Perfect Forward
Secrets
 IPSec Compression
 IPSec Conn. Keep
Alive
 IPSec Tunnel UP
Select the checkbox to enable PFS (Perfect Forward Secrets).
Select the checkbox to enable compression of content on the connection.
When the firewall is located behind a NAT device, it sends keep alive
packets to maintain the connection. You can also force it to send keep
alive packets for all NAT-T connections.
This field indicates the IPSec Tunnel is UP and running.
5.5.1.5. PPTP
If your ISP provides PPTP connection, please select PPTP. And enter the following parameters.
Figure 5-5-6
The page includes the following fields:
Object
Description
 WAN Connections
Select PPTP from the list.
-59-
User Manual of WNAP-6350
 Server IP
 User Name / Password
Enter the IP address of the PPTP server.
Enter the User Name and Password provided by your ISP.
These fields are case-sensitive.
Static IP/ Dynamic IP: Choose either as you are given by your
 Address Mode
ISP and If you choose static IP and enter the domain name,
you should also enter the DNS assigned by your ISP. And click
the Save button.
 IP Address
 Subnet Mask
 Operation Mode
 Keep Alive Mode
 Primary DNS Server
 Secondary DNS Server
Enter the User Name and Password provided by your ISP.
These fields are case-sensitive.
Enter the subnet Mask in dotted-decimal notation provided by
your ISP, usually is 255.255.255.0
Keep Alive: Being constantly connected.
Set up the redial period after the disconnection.
The default setting is "60 seconds".
(Optional) Enter the DNS IP address in dotted-decimal notation
provided by your ISP.
(Optional) Enter another DNS IP address in dotted-decimal
notation provided by your ISP.
5.5.1.6. L2TP
If your ISP provides L2TP connection, please select L2TP and enter the following parameters.
Figure 5-5-7
The page includes the following fields:
Object
Description
 WAN Connections
Select L2TP from the list.
-60-
User Manual of WNAP-6350
 Server IP
 User Name / Password
Enter the IP address of the L2TP server.
Enter the User Name and Password provided by your ISP.
These fields are case-sensitive.
Static IP/ Dynamic IP: Choose either as you are given by your
 Address Mode
ISP and If you choose static IP and enter the domain name,
you should also enter the DNS assigned by your ISP. And click
the Save button.
 IP Address
 Subnet Mask
 Operation Mode
 Keep Alive Mode
 Primary DNS Server
 Secondary DNS Server
Enter the User Name and Password provided by your ISP.
These fields are case-sensitive.
Enter the subnet Mask in dotted-decimal notation provided by
your ISP, usually is 255.255.255.0
Keep Alive: Being constantly connected.
Set up the redial period after the disconnection.
The default setting is "60 seconds".
(Optional) Enter the DNS IP address in dotted-decimal notation
provided by your ISP.
(Optional) Enter another DNS IP address in dotted-decimal
notation provided by your ISP.
5.5.2 LAN
Figure 5-5-8
The page includes the following fields:
Object
Description
 MAC Address
Display the LAN port MAC address of the Wireless AP.
 IP Address
The Wireless AP’s LAN IP.
The default is 192.168.1.1. You can change it according to your need.
-61-
User Manual of WNAP-6350
 Subnet Mask
Enter the subnet mask of the LAN IP.
5.5.2.1. DHCP Server
Figure 5-5-9
The page includes the following fields:
Object
Description
 DHCP Server
Select DHCP Server to enable DHCP server feature.
 Local Domain Name
(Optional)
(Optional) Input the domain name of your network.
 Start IP Address
Enter the starting IP address for the DHCP server’s IP assignment.
 End IP Address
Enter the ending IP address for the DHCP server’s IP assignment.
The length of time for the IP address lease. Configuring a proper
 Lease Time
lease time improves the efficiency for the DHCP server to reclaim
disused IP addresses.
To benefit from the DHCP server feature, you must set all LAN PCs to DHCP clients by selecting the “Obtain an
IP Address Automatically” radio buttons thereon.
5.5.2.2. DHCP Relay
Figure 5-5-10
The page includes the following fields:
Object
Description
 DHCP Server
Select DHCP Relay to enable DHCP relay feature.
 DHCP Relay
A DHCP relay agent is any host that forwards DHCP packets
-62-
User Manual of WNAP-6350
between clients and servers.
Configure the IP address of DHCP Relay host.
5.5.3 VLAN
Figure 5-5-11
The page includes the following fields:
Object
Description
 VLAN Setup
Check this box to enable the VLAN function.
 Management VLAN ID
Configure a specified VLAN to be the management VLAN.
 Enable Management
VLAN ID
Check this box to enable the Management VLAN function.
The ID of a VLAN. Only in the same VLAN can a wireless PC and a
 VLAN ID
wired PC communicate with each other. The value can be between 1
and 4095. If the VLAN function is enabled, when AP forwards
packets, the packets out from the LAN port will be added with an
-63-
User Manual of WNAP-6350
IEEE 802.1Q VLAN Tag, whose VLAN ID is just the ID of the VLAN
where the sender belongs.
5.5.4 Advanced Routing
Figure 5-5-12
The page includes the following fields:
Object
Description
 Destination
The IP address of packets that can be routed.
 Type
Defines the type of destination. ( Host: Signal IP address / Net: Portion
of Network )
 Gateway
Defines the packets destination next hop
 Interface
Select interface to which a static routing subnet is to be applied
-64-
User Manual of WNAP-6350
 Comment
 Dynamic Routing
Protocol
Help identify the routing
Enable or disable the RIP (Routing Information Protocol) for the
WAN or LAN interface.
It supports RIP v1 and v2.
5.5.5 IPv6
Use this section to configure your IPv6 Connection type. If you are unsure of your connection method, please
contact your Internet Service Provider.
Figure 5-5-13
The page includes the following fields:
Object
Description
Choose the mode to be used by the AP/Router to the IPv6 Internet.
 IPv6 Connection Mode
There are 7 connection modes available:
Static, SLAAC, DHCPv6, 6to4 Tunnel, 6in4 Tunnel, PPPoE, and
Pass Through.
 DNS Address Server
Setting
 Prefix Delegation
Enter the IPv6 Primary DNS & IPv6 Secondary DNS to this section.
Enter the IPv6 Prefix Delegation information provided by your
-65-
User Manual of WNAP-6350
Setting
 LAN IPv6 Address
Setting
Internet Service Provider (ISP).
Use this section to configure the internal network settings of your
AP/Router. If you change the LAN IPv6 Address here, you may need
to adjust your PC network settings to access the network again.
IPv6 offers two types of autoconfiguration: Stateful (DHCPv6) &
Stateless (RADVD).
Stateful (DHCPv6):
This type of configuration is suitable for small organizations and
 LAN Address Auto
configuration
individuals. It allows each host to determine its address from the
contents of received user advertisements. It makes use of the IEEE
EUI-64 standard to define the network ID portion of the address.
Stateless(RADVD):
With Stateless Autoconfiguration, a host gains an address via an
interface automatically "leasing" an address and does not require the
establishment of a server to delve out address space.
5.6 Wireless Settings
You could configure the minimum number of Wireless settings for communication, such as Network Name (SSID)
and Channel. The Access Point can be set simply with only the minimum setting items.
5.6.1 Basic
-66-
User Manual of WNAP-6350
5.6.1.1. Wireless Mode – Access Point
Figure 5-6-1
The page includes the following fields:
Object
Description
Click to select Wireless Mode from pull down menu.
There are 4 options available:

Access Point:
This mode allows wireless clients or Stations(STA) to access

WDS Access Point:
This mode enables the wireless interconnection of Access Point in an
 Wireless Mode
IEEE802.11 network .and accept wireless clients at the same time.

WDS Repeater:
Set to this mode to enable the wireless access point repeat the signal
of root access point using WDS.

WDS Client:
Set to this mode to enable wireless client using WDS to connect to
the WDS Access Point.
 Multiple SSID
There is one more SSID available. Select the checkbox to enable it,
enter the descriptive names that you want to use.
-67-
User Manual of WNAP-6350
 Country Code
 Frequency (Channel)
 Site Survey
 Network Mode
Set your country code by clicking the “Set Country Code”.
Set the channel you would like to use. The channel range will be
changed by selecting different domain.
Click “Site Survey” button to observe the signal of remote sites.
Select the operating channel width to WiFi 11gn (mixed), HT20 or
HT40MHz.
An extension channel is a secondary channel used to bond with the
 Extension Channel
primary channel to increase this range to 40MHz. Bonded channels
allow for greater bandwidth on the local network.
To decrease the chances of data retransmission at long distance, the
 Distance
IEEE 802.11b/g/n Wireless Outdoor CPE can automatically adjust
proper ACK timeout value by specifying distance of the two nodes.
ACK/CTS Timeout settings are for long distance links. It is important
to tweak settings to achieve the optimal result based on requirement.
 ACK/CTS Timeout
The device’s default settings should be sufficient for most
applications.
The value is auto determined by distance between the radios, data
rate of average environment.
It is the wireless network name. The SSID can be 32 bytes long.
 Network Name (SSID)
User can use the default SSID or change it.
The default SSID is WNAP-6350.
 WPS Choice
Enable it to use WPS associating with AP or Client device.
 Encryption Settings
Select the encryption type that you would like to use.
 WPA Algorithms
Select the WPA Algorithms that you would like to use.
 Key Renewal Interval
The key renewal time is the period of time that the AP uses the same
(Seconds)
 Pre-Shared Key
key before a new one is generated.
Data encryption and key are required for wireless authentication.
-68-
User Manual of WNAP-6350
5.6.1.2. Wireless Mode – WDS Access Point
Figure 5-6-2
The page includes the following fields:
Object
Description
Click to select Wireless Mode from pull down menu.
There are 4 options available:
Access Point:
This mode allows wireless clients or Stations(STA) to access
WDS Access Point:
This mode enables the wireless interconnection of Access Point in an
 Wireless Mode
IEEE802.11 network .and accept wireless clients at the same time.
WDS Repeater:
Set to this mode to enable the wireless access point repeat the signal
of root access point using WDS.
WDS Client:
Set to this mode to enable wireless client using WDS to connect to
the WDS Access Point.
 Country Code
 Frequency (Channel)
Set your country code by clicking the “Set Country Code”.
Set the channel you would like to use. The channel range will be
changed by selecting different domain.
-69-
User Manual of WNAP-6350
 Site Survey
 Network Mode
Click “Site Survey” button to observe the signal of remote sites.
Select the operating channel width to WiFi 11gn (mixed), HT20 or
HT40MHz.
An extension channel is a secondary channel used to bond with the
 Extension Channel
primary channel to increase this range to 40MHz. Bonded channels
allow for greater bandwidth on the local network.
To decrease the chances of data retransmission at long distance, the
 Distance
IEEE 802.11b/g/n Wireless Outdoor CPE can automatically adjust
proper ACK timeout value by specifying distance of the two nodes.
ACK/CTS Timeout settings are for long distance links. It is important
to tweak settings to achieve the optimal result based on requirement.
 ACK/CTS Timeout
The device’s default settings should be sufficient for most
applications.
The value is auto determined by distance between the radios, data
rate of average environment.
It is the wireless network name. The SSID can be 32 bytes long.
 Network Name (SSID)
User can use the default SSID or change it.
The default SSID is WNAP-6350.
 Encryption Settings
Select the encryption type that you would like to use.
 WPA Algorithms
Select the WPA Algorithms that you would like to use.
 Key Renewal Interval
The key renewal time is the period of time that the AP uses the same
(Seconds)
 Pre-Shared Key
key before a new one is generated.
Data encryption and key are required for wireless authentication.
-70-
User Manual of WNAP-6350
5.6.1.3. Wireless Mode – WDS Repeater
Figure 5-6-3
The page includes the following fields:
Object
Description
Click to select Wireless Mode from pull down menu.
There are 4 options available:
Access Point:
This mode allows wireless clients or Stations(STA) to access
WDS Access Point:
This mode enables the wireless interconnection of Access Point in an
 Wireless Mode
IEEE802.11 network .and accept wireless clients at the same time.
WDS Repeater:
Set to this mode to enable the wireless access point repeat the signal
of root access point using WDS.
WDS Client:
Set to this mode to enable wireless client using WDS to connect to
the WDS Access Point.
 Root AP MAC Address
(optional)
 Country Code
Fill out the Root AP’s MAC Address enable it to connect to the Root
AP using WDS.
Set your country code by clicking the “Set Country Code”.
-71-
User Manual of WNAP-6350
 Frequency (Channel)
 Site Survey
 Network Mode
Set the channel you would like to use. The channel range will be
changed by selecting different domain.
Click “Site Survey” button to observe the signal of remote sites.
Select the operating channel width to WiFi 11gn (mixed), HT20 or
HT40MHz.
An extension channel is a secondary channel used to bond with the
 Extension Channel
primary channel to increase this range to 40MHz. Bonded channels
allow for greater bandwidth on the local network.
To decrease the chances of data retransmission at long distance, the
 Distance
IEEE 802.11b/g/n Wireless Outdoor CPE can automatically adjust
proper ACK timeout value by specifying distance of the two nodes.
ACK/CTS Timeout settings are for long distance links. It is important
to tweak settings to achieve the optimal result based on requirement.
 ACK/CTS Timeout
The device’s default settings should be sufficient for most
applications.
The value is auto determined by distance between the radios, data
rate of average environment.
It is the wireless network name of itself. The SSID can be 32 bytes
 Network Name (SSID)
long.
User can use the default SSID or change it.
The default SSID is WNAP-6350.
It is the wireless network name of Root AP.
 Root AP SSID
The SSID must be the same with Root AP so that the connection can
be established successfully.
 Encryption Settings
Select the encryption type that you would like to use.
 WPA Algorithms
Select the WPA Algorithms that you would like to use.
 Key Renewal Interval
The key renewal time is the period of time that the AP uses the same
(Seconds)
 Pre-Shared Key
key before a new one is generated.
Data encryption and key are required for wireless authentication.
-72-
User Manual of WNAP-6350
5.6.1.4. Wireless Mode – WDS Client
Figure 5-6-4
The page includes the following fields:
Object
Description
Click to select Wireless Mode from pull down menu.
There are 4 options available:
Access Point:
This mode allows wireless clients or Stations(STA) to access
WDS Access Point:
This mode enables the wireless interconnection of Access Point in an
 Wireless Mode
IEEE802.11 network .and accept wireless clients at the same time.
WDS Repeater:
Set to this mode to enable the wireless access point repeat the signal
of root access point using WDS.
WDS Client:
Set to this mode to enable wireless client using WDS to connect to
the WDS Access Point.
 Root AP MAC Address
(optional)
 Country Code
Fill out the Root AP’s MAC Address enable it to connect to the Root
AP using WDS.
Set your country code by clicking the “Set Country Code”.
-73-
User Manual of WNAP-6350
 Frequency (Channel)
 Network Mode
Set the channel you would like to use. The channel range will be
changed by selecting different domain.
Select the operating channel width to WiFi 11gn (mixed), HT20 or
HT40MHz.
An extension channel is a secondary channel used to bond with the
 Extension Channel
primary channel to increase this range to 40MHz. Bonded channels
allow for greater bandwidth on the local network.
To decrease the chances of data retransmission at long distance, the
 Distance
IEEE 802.11b/g/n Wireless Outdoor CPE can automatically adjust
proper ACK timeout value by specifying distance of the two nodes.
ACK/CTS Timeout settings are for long distance links. It is important
to tweak settings to achieve the optimal result based on requirement.
 ACK/CTS Timeout
The device’s default settings should be sufficient for most
applications.
The value is auto determined by distance between the radios, data
rate of average environment.
It is the wireless network name of Root AP.
 Root AP SSID
The SSID must be the same with Root AP so that the connection can
be established successfully.
Click “Scan” to site survey the Root AP.
 Encryption Settings
Select the encryption type that you would like to use.
 WPA Algorithms
Select the WPA Algorithms that you would like to use.
 Key Renewal Interval
The key renewal time is the period of time that the AP uses the same
(Seconds)
 Pre-Shared Key
key before a new one is generated.
Data encryption and key are required for wireless authentication.
-74-
User Manual of WNAP-6350
5.6.2 Profile Settings
In Client Bridge and Client Router operation modes, please go to “Advanced-> Wireless Settings-> Profile
Settings” to configure the wireless client function to connect with the wireless AP.
Figure 5-6-5
The page includes the following fields:
Object
 Profile Name
Description
Fill out the Root AP’s MAC Address enabling it to connect to the Root
AP using WDS.
Set the Network Type that you would like to use.
Infrastructure:
Infrastructure networks consist of the networked devices and the
wireless access point or wireless router. Each device must connect to
 Network Type
the access point before having access to other computers on the
network.
Ad-hoc:
In an ad hoc network, each device's network adapter directly
communicates with other devices.
 SSID
It is the wireless network name of Root AP.
-75-
User Manual of WNAP-6350
 BSSID (optional)
Indicate the Basic Service Set ID of the associated AP
 Encryption Settings
Select the encryption type that you would like to use.
To decrease the chances of data retransmission at long distance, the
 Distance
IEEE 802.11b/g/n Wireless Outdoor CPE can automatically adjust
proper ACK timeout value by specifying distance of the two nodes.
ACK/CTS Timeout settings are for long distance links. It is important
to tweak settings to achieve the optimal result based on requirement.
 ACK/CTS Timeout
The device’s default settings should be sufficient for most
applications.
The value is auto determined by distance between the radios, data
rate of average environment.
RTS/CTS (Request to Send / Clear to Send) is the optional
 RTS/CTS
mechanism used by the 802.11 wireless networking protocol to
reduce frame collisions introduced by the hidden node problem.
You can enter a setting ranging from 0 to 2347 bytes.
The fragmentation threshold determines the size at which packets
 Fragmentation
Threshold
are fragmented (sent as several pieces instead of as one block). Use
a low setting in areas where communication is poor or where there is
a great deal of radio interference. This function will help you to
improve the network performance.
 WDS Client
Check it to enable WDS Client function.
-76-
User Manual of WNAP-6350
5.6.3 Advanced
Figure 5-6-6
The page includes the following fields:
Object
Description
 Wireless On/Off
Click this button to switch the Wireless Radio On or Off.
 AP MAC Address
Display the AP MAC Address of wireless interface.
In a packet-based communications network, packet aggregation is
 Packet Aggregate
the process of joining multiple packets together into a single
transmission unit, in order to reduce the overhead associated with
each transmission.
WMM function can guarantee the packets with high-priority
 WMM
messages
being
transmitted
preferentially.
It
is
strongly
recommended enabled.
The beacons are the packets sent by the Device to synchronize a
 Beacon Interval
wireless network. Beacon Interval value determines the time
interval of the beacons. You can specify a value between 20-1000
-77-
User Manual of WNAP-6350
milliseconds. The default value is 100.
This value determines the interval of the Delivery Traffic Indication
 DTIM
Message (DTIM). You can specify the value between 1-255
Beacon Intervals. The default value is 1, which indicates the DTIM
Interval is the same as Beacon Interval.
The RTS/CTS mechanism is widely used in wireless networks in
 RTS/CTS
order to avoid packet collisions and, thus, achieve high
throughput.
This value is the maximum size determining whether packets will
 Fragmentation Threshold
be fragmented. Setting the Fragmentation Threshold too low may
result in poor network performance since excessive packets. 2346
is the default setting and is recommended.
 Station Control (SSID I)
Fill out the Station Control value of SSID I.
 Station Control (SSID II)
Fill out the Station Control value of SSID II.
Isolate all connected wireless stations so that wireless stations
 Wireless Isolate
cannot access each other through WLAN. This function will be
disabled if WDS/Bridge is enabled.
Set the AP to the external LED lights and wireless signal strength
 Thresholds, dbm
received correspondence, when the AP receives the wireless
signal,
according
to
the
wireless
signal
strength,
the
corresponding LED will be lit.
5.6.4 Access Control
Choose menu “Advanced-> Wireless Settings-> Access Control” to configure the filtering rules for the clients
who would like to associate with Wireless AP.
-78-
User Manual of WNAP-6350
Figure 5-6-7
The page includes the following fields:
Object
 SSID
Description
Select the SSID which you would like to configure access
control.
Allow Listed: allow the packets not specified by any access
 Access Control Mode
control policy to pass through the AP Router.
Deny Listed: deny the packets not specified by any access
control policy to pass through the AP Router.
 MAC Address
 Current Access
Control List
Configure the MAC Address to apply the access control.
Display the current Access Control List.
5.7 Logout
Select “Logout”, and then click “Yes” to logout the system.
Figure 5-7-1
Figure 5-7-2
-79-
User Manual of WNAP-6350
Appendix A: FAQ
1. What and how to find my PC’s IP and MAC address?
IP address is the identifier for a computer or device on a TCP/IP network. Networks using the TCP/IP protocol
route messages based on the IP address of the destination. The format of an IP address is a 32-bit numeric
address written as four numbers separated by periods. Each number can be zero to 255. For example,
191.168.1.254 could be an IP address
The MAC (Media Access Control) address is your computer's unique hardware number. (On an Ethernet LAN,
it's the same as your Ethernet address.) When you're connected to the Internet from your computer (or host as
the Internet protocol thinks of it), a correspondence table relates your IP address to your computer's physical
(MAC) address on the LAN.
To find your PC’s IP and MAC address,
(1) Open the Command program in the Microsoft Windows.
(2) Type in “ipconfig /all”, then press the Enter button.
(3) Your PC’s IP address is the one entitled IP Address and your PC’s MAC address is the one entitled
Physical Address.
2. What is Wireless LAN?
A wireless LAN (WLAN) is a network that allows access to Internet without the need for any wired connections to
the user’s machine.
3. What are ISM bands?
ISM stands for Industrial, Scientific and Medical; radio frequency bands that the Federal Communications
Commission (FCC) authorized for wireless LANs. The ISM bands are located at 915 +/-13 MHz, 2450 +/-50 MHz
and 5800 +/-75 MHz.
4. How does wireless networking work?
The 802.11 standard define two modes: infrastructure mode and ad hoc mode. In infrastructure mode, the
wireless network consists of at least one access point connected to the wired network infrastructure and a set of
wireless end stations. This configuration is called a Basic Service Set (BSS). An Extended Service Set (ESS) is
a set of two or more BSSs forming a single sub-network. Since most corporate WLANs require access to the
wired LAN for services (file servers, printers, Internet links) they will operate in infrastructure mode.
-80-
User Manual of WNAP-6350
Example 1: wireless Infrastructure Mode
Ad hoc mode (also called peer-to-peer mode or an Independent Basic Service Set, or IBSS) is simply a set of
802.11 wireless stations that communicate directly with one another without using an access point or any
connection to a wired network. This mode is useful for quickly and easily setting up a wireless network anywhere
that a wireless infrastructure does not exist or is not required for services, such as a hotel room, convention
center, or airport, or where access to the wired network is barred (such as for consultants at a client site).
Example 2: wireless Ad Hoc Mode
5. What is BSSID?
A six-byte address is that distinguish a particular a particular access point from others. Also know as just SSID.
Serve as a network ID or name.
6. What is ESSID?
The Extended Service Set ID (ESSID) is the name of the network you want to access. It is used to identify
different wireless networks.
7. What are potential factors that may causes interference?
Factors of interference:



Obstacles: walls, ceilings, furniture… etc.
Building Materials: metal door, aluminum studs.
Electrical devices: microwaves, monitors and electrical motors.
-81-
User Manual of WNAP-6350
Solutions to overcome the interferences:




8.
Minimizing the number of walls and ceilings.
Position the WLAN antenna for best reception.
Keep WLAN devices away from other electrical devices, eg: microwaves, monitors, electric
motors…etc.
Add additional WLAN Access Points if necessary.
What are the Open System and Shared Key authentications?
IEEE 802.11 supports two subtypes of network authentication services: open system and shared key. Under
open system authentication, any wireless station can request authentication. The station that needs to
authenticate with another wireless station sends an authentication management frame that contains the identity
of the sending station. The receiving station then returns a frame that indicates whether it recognizes the
sending station. Under shared key authentication, each wireless station is assumed to have received a secret
shared key over a secure channel that is independent from the 802.11 wireless network communications
channel.
9. What is WEP?
An option of IEEE 802.11 function is that offers frame transmission privacy similar to a wired network. The Wired
Equivalent Privacy generates secret shared encryption keys that both source and destination stations can use to
alert frame bits to avoid disclosure to eavesdroppers.
WEP relies on a secret key that is shared between a mobile station (e.g. a laptop with a wireless Ethernet card)
and an access point (i.e. a base station). The secret key is used to encrypt packets before they are transmitted,
and an integrity check is used to ensure that packets are not modified in transit.
10. What is Fragment Threshold?
The proposed protocol uses the frame fragmentation mechanism defined in IEEE 802.11 to achieve parallel
transmissions. A large data frame is fragmented into several fragments each of size equal to fragment threshold.
By tuning the fragment threshold value, we can get varying fragment sizes. The determination of an efficient
fragment threshold is an important issue in this scheme. If the fragment threshold is small, the overlap part of the
master and parallel transmissions is large. This means the spatial reuse ratio of parallel transmissions is high. In
contrast, with a large fragment threshold, the overlap is small and the spatial reuse ratio is low. However high
fragment threshold leads to low fragment overhead. Hence there is a trade-off between spatial re-use and
fragment overhead.
Fragment threshold is the maximum packet size used for fragmentation. Packets larger than the size
programmed in this field will be fragmented.
If you find that your corrupted packets or asymmetric packet reception (all send packets, for example). You may
want to try lowering your fragmentation threshold. This will cause packets to be broken into smaller fragments.
These small fragments, if corrupted, can be resent faster than a larger fragment. Fragmentation increases
-82-
User Manual of WNAP-6350
overhead, so you'll want to keep this value as close to the maximum value as possible.
11. What is RTS (Request to Send) Threshold?
The RTS threshold is the packet size at which packet transmission is governed by the RTS/CTS transaction. The
IEEE 802.11-1997 standard allows for short packets to be transmitted without RTS/ CTS transactions. Each
station can have a different RTS threshold. RTS/CTS is used when the data packet size exceeds the defined
RTS threshold. With the CSMA/CA transmission mechanism, the transmitting station sends out an RTS packet
to the receiving station, and waits for the receiving station to send back a CTS (Clear to Send) packet before
sending the actual packet data.
This setting is useful for networks with many clients. With many clients, and a high network load, there will be
many more collisions. By lowering the RTS threshold, there may be fewer collisions, and performance should
improve. Basically, with a faster RTS threshold, the system can recover from problems faster. RTS packets
consume valuable bandwidth, however, so setting this value too low will limit performance.
12. What is Beacon Interval?
In addition to data frames that carry information from higher layers, 802.11 include management and control
frames that support data transfer. The beacon frame, which is a type of management frame, provides the
"heartbeat" of a wireless LAN, enabling stations to establish and maintain communications in an orderly fashion.
Beacon Interval represents the amount of time between beacon transmissions. Before a station enters power
save mode, the station needs the beacon interval to know when to wake up to receive the beacon (and learn
whether there are buffered frames at the access point).
13. What is Preamble Type?
There are two preamble types defined in IEEE 802.11 specification. A long preamble basically gives the decoder
more time to process the preamble. All 802.11 devices support a long preamble. The short preamble is designed
to improve efficiency (for example, for VoIP systems). The difference between the two is in the Synchronization
field. The long preamble is 128 bits, and the short is 56 bits.
14. What is SSID Broadcast?
Broadcast of SSID is done in access points by the beacon. This announces your access point (including various
bits of information about it) to the wireless world around it. By disabling that feature, the SSID configured in the
client must match the SSID of the access point.
Some wireless devices don't work properly if SSID isn't broadcast (for example the D-link DWL-120 USB
802.11b adapter). Generally if your client hardware supports operation with SSID disabled, it's not a bad idea to
run that way to enhance network security. However it's no replacement for WEP, MAC filtering or other
protections.
-83-
User Manual of WNAP-6350
15. What is Wi-Fi Protected Access (WPA)?
Wi-Fi’s original security mechanism, Wired Equivalent Privacy (WEP), has been viewed as insufficient for
securing confidential business communications. A longer-term solution, the IEEE 802.11i standard, is under
development. However, since the IEEE 802.11i standard is not expected to be published until the end of 2003,
several members of the WI-Fi Alliance teamed up with members of the IEEE 802.11i task group to develop a
significant near-term enhancement to Wi-Fi security. Together, this team developed Wi-Fi Protected Access.
To upgrade a WLAN network to support WPA, Access Points will require a WPA software upgrade. Clients will
require a software upgrade for the network interface card, and possibly a software update for the operating
system. For enterprise networks, an authentication server, typically one that supports RADIUS and the selected
EAP authentication protocol, will be added to the network.
16. What is WPA2?
It is the second generation of WPA. WPA2 is based on the final IEEE 802.11i amendment to the 802.11
standard.
17. What is 802.1x Authentication?
802.1x is a framework for authenticated MAC-level access control, defines Extensible Authentication Protocol
(EAP) over LANs (WAPOL). The standard encapsulates and leverages much of EAP, which was defined for
dial-up authentication with Point-to-Point Protocol in RFC 2284.
Beyond encapsulating EAP packets, the 802.1x standard also defines EAPOL messages that convey the shared
key information critical for wireless security.
18. What is Temporal Key Integrity Protocol (TKIP)?
The Temporal Key Integrity Protocol, pronounced tee-kip, is part of the IEEE 802.11i encryption standard for
wireless LANs. TKIP is the next generation of WEP, the Wired Equivalency Protocol, which is used to secure
802.11 wireless LANs. TKIP provides per-packet key mixing, a message integrity check and a re-keying
mechanism, thus fixing the flaws of WEP.
19. What is Advanced Encryption Standard (AES)?
Security issues are a major concern for wireless LANs, AES is the U.S. government’s next-generation
cryptography algorithm, which will replace DES and 3DES.
20. What is Inter-Access Point Protocol (IAPP)?
The IEEE 802.11f Inter-Access Point Protocol (IAPP) supports Access Point Vendor interoperability, enabling
roaming of 802.11 Stations within IP subnet.
IAPP defines messages and data to be exchanged between Access Points and between the IAPP and high layer
management entities to support roaming. The IAPP protocol uses TCP for inter-Access Point communication
and UDP for RADIUS request/response exchanges. It also uses Layer 2 frames to update the forwarding tables
-84-
User Manual of WNAP-6350
of Layer 2 devices.
21. What is Wireless Distribution System (WDS)?
The Wireless Distribution System feature allows WLAN AP to talk directly to other APs via wireless channel, like
the wireless WDS or repeater service.
22. What is Universal Plug and Play (UPnP)?
UPnP is an open networking architecture that consists of services, devices, and control points. The ultimate goal
is to allow data communication among all UPnP devices regardless of media, operating system, programming
language, and wired/wireless connection.
23. What is Maximum Transmission Unit (MTU) Size?
Maximum Transmission Unit (MTU) indicates the network stack of any packet is larger than this value will be
fragmented before the transmission. During the PPP negotiation, the peer of the PPP connection will indicate its
MRU and will be accepted. The actual MTU of the PPP connection will be set to the smaller one of MTU and the
peer’s MRU.
24. What is Clone MAC Address?
Clone MAC address is designed for your special application that request the clients to register to a server
machine with one identified MAC address. Since that all the clients will communicate outside world through the
WLAN Broadband Router, so have the cloned MAC address set on the WLAN Broadband Router will solve the
issue.
25. What is DDNS?
DDNS is the abbreviation of Dynamic Domain Name Server. It is designed for user owned the DNS server with
dynamic WAN IP address.
26. What is NTP Client?
NTP client is designed for fetching the current timestamp from internet via Network Time protocol. User can
specify time zone, NTP server IP address.
27. What is VPN?
VPN is the abbreviation of Virtual Private Network. It is designed for creating point-to point private link via shared
or public network.
28. What is IPSEC?
IPSEC is the abbreviation of IP Security. It is used to transferring data securely under VPN.
-85-
User Manual of WNAP-6350
29. What is WLAN Block Relay between Clients?
An Infrastructure Basic Service Set is a BSS with a component called an Access Point (AP). The access point
provides a local relay function for the BSS. All stations in the BSS communicate with the access point and no
longer communicate directly. All frames are relayed between stations by the access point. This local relay
function effectively doubles the range of the IBSS.
30. What is WMM?
WMM is based on a subset of the IEEE 802.11e WLAN QoS draft standard. WMM adds prioritized capabilities to
Wi-Fi networks and optimizes their performance when multiple concurring applications, each with different
latency and throughput requirements, compete for network resources. By using WMM, end-user satisfaction is
maintained in a wider variety of environments and traffic conditions. WMM makes it possible for home network
users and enterprise network managers to decide which data streams are most important and assign them a
higher traffic priority.
31. What is WLAN ACK TIMEOUT?
ACK frame has to receive ACK timeout frame. If remote does not receive in specified period, it will be
retransmitted.
32. What is Modulation Coding Scheme (MCS)?
MCS is Wireless link data rate for 802.11n. The throughput/range performance of an AP will depend on its
implementation of coding schemes. MCS includes variables such as the number of spatial streams, modulation,
and the data rate on each stream. Radios establishing and maintaining a link must automatically negotiate the
optimum MCS based on channel conditions and then continuously adjust the selection of MCS as conditions
change due to interference, motion, fading, and other events.
33. What is Frame Aggregation?
Every 802.11 packet, no matter how small, has a fixed amount of overhead associated with it. Frame
Aggregation combines multiple smaller packets together to form one larger packet. The larger packet can be
sent without the overhead of the individual packets. This technique helps improve the efficiency of the 802.11n
radio allowing more end user data to be sent in a given time.
34. What is Guard Intervals (GI)?
A GI is a period of time between symbol transmission that allows reflections (from multipath) from the previous
data transmission to settle before transmitting a new symbol. The 802.11n specifies two guard intervals: 400ns
(short) and 800ns (long). Support of the 400ns GI is optional for transmit and receive. The purpose of a guard
interval is to introduce immunity to propagation delays, echoes, and reflections to which digital data is normally
very sensitive.
-86-
User Manual of WNAP-6350
Appendix B: Configuring the PC in Windows 7
In this section, we’ll introduce how to configure the TCP/IP correctly in Windows 7. First make sure your Network
Adapter is working; refer to the adapter’s manual if needed.
1)
On the Windows taskbar, click the Start button, and then click Control Panel.
2)
Click the Network and Sharing Center icon, and then click the Change adapter settings on the left
side of the screen.
Figure B-1
3)
Right click the icon of the network adapter shown in the figure below, and select Properties on the
prompt window.
-87-
User Manual of WNAP-6350
Figure B-2
4)
On the prompt page shown below, double click on the Internet Protocol Version 4 (TCP/IPv4).
Figure B-3
-88-
User Manual of WNAP-6350
5)
The following TCP/IP Properties window will display and the IP Address tab is open on this window
by default.
Now you can configure the TCP/IP protocol below:
 Setting IP address manually
1
Select Use the following IP address radio button.
2
If the AP's LAN IP address is 192.168.1.1, type in IP address 192.168.1.x (x is from 2 to 254), and Subnet
mask 255.255.255.0.
3
Select Use the following DNS server addresses radio button. In the Preferred DNS Server field you can
type the DNS server IP address which has been provided by your ISP
Figure B-4
Now click OK to keep your settings.
-89-
User Manual of WNAP-6350
Appendix C: Use Planet Smart Discovery to find AP
To easily discover the WNAP-6350 in your Ethernet environment, the Planet Smart Discovery Utility from user’s
manual CD-ROM is an ideal solution.
The following install instructions guide you to run the Planet Smart Discovery Utility.
Step 1: Deposit the Planet Smart Discovery Utility in administrator PC.
Step 2: Execute this utility.
Step 3: Click “Refresh” button to update the current connected devices list; the screen is shown as follows:
Figure C-1
Step 3: Select the WNAP-6350 from the list, and then click “Connect to Device” button to login the Web
Management Configuration Page.
The fields in white background can be modified directly, and then you can apply the new
setting by clicking the “Update Device” button.
-90-
User Manual of WNAP-6350
Appendix D: Specifications
Product
WNAP-6350
2.4GHz 300Mbps 802.11n Wireless Outdoor Access Point
Hardware Specifications
IEEE 802.11b/g/n Wireless LAN
IEEE 802.11i Wireless Security
Standard
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Ethernet
IEEE 802.3x Flow Control
IEEE 802.3af/at Power over Ethernet / PD
Memory
32 Mbytes DDR SDRAM
8 Mbytes Flash
Wireless IEEE 802.11b/g/n, 2T2R
Interface
LAN: 1 x 10/100Base-TX, Auto-MDI / MDIX, IEEE 802.3af/at PoE / PD port
WAN: 1 x 10/100Base-TX, Auto-MDI / MDIX
Antenna
N-Type Female connectors x 2
Wireless RF Specifications
Wireless Technology
IEEE 802.11b/g
IEEE 802.11n
IEEE 802.11b: 11, 5.5, 2 and 1Mbps
Data Rate
IEEE 802.11g: 54, 48, 36, 24, 18, 12, 9 and 6Mbps
IEEE 802.11n (20MHz): up to 150Mbps
IEEE 802.11n (40MHz): up to 300Mbp
Media Access Control
CSMA / CA
Modulation
Transmission/Emission Type: DSSS / OFDM
Data modulation type: OFDM with BPSK, QPSK, 16-QAM, 64-QAM,
DBPSK, DQPSK, CCK
Frequency Band
2.412GHz ~ 2.484GHz
Operating Channel
America/ FCC: 2.414~2.462GHz (11 Channels)
Europe/ ETSI: 2.412~2.472GHz (13 Channels)
Japan/ TELEC: 2.412~2.484GHz (14 Channels)
RF Output Power (Max.)
IEEE 802.11b/g: 29 ± 1.5dBm
IEEE 802.11n: 25 ± 1.5dBm
IEEE 802.11b: -95/ -94/ -92/ -90dBm (1/ 2/ 5.5/ 11Mbps)
Receiver Sensitivity
IEEE 802.11g: -90/ -82/ -80/ -75dBm (6/ 24/ 36/ 54Mbps)
IEEE 802.11n: -91/ -83/ -74/ -89/ -80/ -72dBm (MCS 0/ 3/ 6/ 9/ 12/ 15)
Output Power Control
3~29dBm
Software Features
LAN
WAN
Built-in DHCP server supporting static IP address distributing
Supports 802.1d STP (Spanning Tree)
 Static IP
-91-
User Manual of WNAP-6350
 Dynamic IP
 PPPoE
 PPTP
 L2TP
 IPSec
 Bridge
Operating Mode
 Gateway
 WISP
NAT firewall with SPI (Stateful Packet Inspection)
Firewall
Built-in NAT server supporting Virtual Server and DMZ
Built-in firewall with Port / IP address / MAC / URL filtering
 AP
 Client
Wireless Mode
 WDS PTP
 WDS PTMP
 WDS Repeater (AP+WDS)
Channel Width
Wireless Isolation
Encryption Type
20MHz / 40MHz
Enables isolation of each connected wireless client from communicating with
each other mutually.
64/128-bits WEP, WPA, WPA-PSK, WPA2, WPA2-PSK, 802.1X
Provides wireless LAN ACL (Access Control List) filtering
Wireless Security
Wireless MAC address filtering
Supports WPS (Wi-Fi Protected Setup )
Enable / Disable SSID Broadcast
Multiple SSID
Up to 2
Max. Wireless Client
40
Max. WDS AP
8
Max. Wired Client
60
WMM
Supports Wi-Fi Multimedia
QoS
Supports Quality of Service for bandwidth control
NTP
Network Time Management
Management
Web UI, DHCP Client, Configuration Backup & Restore, Dynamic DNS, SNMP
Diagnostic tool
System Log, Ping Watchdog
Mechanical & Power
IP Rate
IP67
Material
Aluminum
Dimensions (W x D x H)
320 x 27.5 x 320 mm
Weight
2.4kg
Installation
Pole mounting or Wall mounting
Power Requirements
Power Consumption
AP: IEEE 802.3af/at PoE / 48VDC input (PoE Injector included)
PoE Injector: 100~240VAC
7.68W
Environment & Certification
-92-
User Manual of WNAP-6350
Operation Temperature
-30~75 degrees C
Operating Humidity
10~95% non-condensing
Regulatory
CE / RoHS
Accessory
 48VDC IEEE 802.3af PoE injector & Power cord x 1
 Mounting Kit x 1
Standard Accessories
 Waterproof RJ-45 Connector Kit x 2
 Quick Installation Guide x 1
 CD (User’s Manual, Quick Installation Guide) x 1
-93-
EC Declaration of Conformity
For the following equipment:
*Type of Product
:
2.4GHz 802.11n 300Mbps Wireless LAN Outdoor AP/Router
with Industrial IP67 Enclosure (2x N-type connector)
*Model Number
:
WNAP-6350
* Produced by:
Manufacturer’s Name :
Manufacturer’s Address:
Planet Technology Corp.
10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan (R.O.C.)
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to 1999/5/EC R&TTE. For the
evaluation regarding the R&TTE the following standards were applied:
EN 60950-1
EN 300 328 V1.7.1
EN 301 489-1 V1.8.1
EN 301 489-17 V2.1.1
(2006 + A11: 2009 + A1:2010 + A12:2011)
(2006-10)
(2008-04)
(2009-05)
Responsible for marking this declaration if the:
 Manufacturer
 Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name:
Planet Technology Corp.
Company Address:
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.)
Person responsible for making this declaration
Name, Surname
Kent Kang
Position / Title :
Product Manager
Taiwan
Place
5th Feb., 2013
Date
Legal Signature
PLANET TECHNOLOGY CORPORATION
e-mail: [email protected]
http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528
EC Declaration of Conformity
U
English
Hereby, PLANET Technology Corporation,
declares that this 300Mbps 802.11b/g/n Wireless
Outdoor AP/Router is in compliance with the
essential requirements and other relevant
provisions of Directive 1999/5/EC.
Lietuviškai
Šiuo PLANET Technology Corporation,, skelbia,
kad 300Mbps 802.11b/g/n Wireless Outdoor
AP/Router tenkina visus svarbiausius 1999/5/EC
direktyvos reikalavimus ir kitas svarbias nuostatas.
Česky
Společnost PLANET Technology Corporation,
tímto prohlašuje, že tato 300Mbps 802.11b/g/n
Wireless Outdoor AP/Router splňuje základní
požadavky a další příslušná ustanovení směrnice
1999/5/EC.
Magyar
A gyártó PLANET Technology Corporation, kijelenti,
hogy ez a 300Mbps 802.11b/g/n Wireless Outdoor
AP/Router megfelel az 1999/5/EK irányelv
alapkövetelményeinek és a kapcsolódó
rendelkezéseknek.
Dansk
PLANET Technology Corporation, erklærer
herved, at følgende udstyr 300Mbps 802.11b/g/n
Wireless Outdoor AP/Router overholder de
væsentlige krav og øvrige relevante krav i direktiv
1999/5/EF
Malti
Hawnhekk, PLANET Technology Corporation,
jiddikjara li dan 300Mbps 802.11b/g/n Wireless
Outdoor AP/Router jikkonforma mal-ħtiġijiet
essenzjali u ma provvedimenti oħrajn relevanti li
hemm fid-Dirrettiva 1999/5/EC
Deutsch
Hiermit erklärt PLANET Technology Corporation,
dass sich dieses Gerät 300Mbps 802.11b/g/n
Wireless Outdoor AP/Router in Übereinstimmung
mit den grundlegenden Anforderungen und den
anderen relevanten
Nederlands
Hierbij verklaart , PLANET Technology orporation,
dat 300Mbps 802.11b/g/n Wireless Outdoor
AP/Router in overeenstemming is met de essentiële
eisen en de andere relevante bepalingen van richtlijn
1999/5/EG
Vorschriften der Richtlinie 1999/5/EG befindet".
(BMWi)
Eestikeeles
Käesolevaga kinnitab PLANET Technology
Corporation, et see 300Mbps 802.11b/g/n
Wireless Outdoor AP/Router vastab Euroopa
Nõukogu direktiivi 1999/5/EC põhinõuetele ja
muudele olulistele tingimustele.
Polski
Niniejszym firma PLANET Technology Corporation,
oświadcza, że 300Mbps 802.11b/g/n Wireless
Outdoor AP/Router spełnia wszystkie istotne wymogi
i klauzule zawarte w dokumencie „Directive
1999/5/EC”.
Ελληνικά
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ , PLANET Technology
Corporation, ΔΗΛΩΝΕΙ ΟΤΙ ΑΥΤΟ 300Mbps
802.11b/g/n Wireless Outdoor
AP/RouterΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ
ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ
Português
PLANET Technology Corporation, declara que este
300Mbps 802.11b/g/n Wireless Outdoor AP/Router
está conforme com os requisitos essenciais e outras
disposições da Directiva 1999/5/CE.
Slovensky
Výrobca PLANET Technology Corporation, týmto
deklaruje, že táto 300Mbps 802.11b/g/n Wireless
Outdoor AP/Router je v súlade so základnými
požiadavkami a ďalšími relevantnými predpismi
smernice 1999/5/EC.
ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ
Español
Por medio de la presente, PLANET Technology
Corporation, declara que 300Mbps 802.11b/g/n
Wireless Outdoor AP/Router cumple con los
requisitos esenciales y cualesquiera otras
disposiciones aplicables o exigibles de
la Directiva 1999/5/CE
Français
Par la présente, PLANET Technology
Corporation, déclare que les appareils du
300Mbps 802.11b/g/n Wireless Outdoor
AP/Router sont conformes aux exigences
essentielles et aux autres dispositions pertinentes
de la directive 1999/5/CE
Slovensko
PLANET Technology Corporation, s tem potrjuje,
da je ta 300Mbps 802.11b/g/n Wireless Outdoor
AP/Router skladen/a z osnovnimi zahtevami in
ustreznimi določili Direktive 1999/5/EC.
Italiano
Con la presente , PLANET Technology
Corporation, dichiara che questo 300Mbps
802.11b/g/n Wireless Outdoor AP/Router è
conforme ai requisiti essenziali ed alle altre
disposizioni pertinenti stabilite dalla direttiva
Suomi
PLANET Technology Corporation, vakuuttaa täten
että 300Mbps 802.11b/g/n Wireless Outdoor
AP/Router tyyppinen laite on direktiivin 1999/5/EY
oleellisten vaatimusten ja sitä koskevien direktiivin
muiden ehtojen mukainen.
Svenska
Härmed intygar, PLANET Technology Corporation,
att denna 300Mbps 802.11b/g/n Wireless Outdoor
AP/Router står i överensstämmelse med de
väsentliga egenskapskrav och övriga relevanta
bestämmelser som framgår av direktiv 1999/5/EG.
1999/5/CE.
Latviski
Ar šo PLANET Technology Corporation,
apliecina, ka šī 300Mbps 802.11b/g/n Wireless
Outdoor AP/Router atbilst Direktīvas 1999/5/EK
pamatprasībām un citiem atbilstošiem
noteikumiem.