Download UM10208 LPC288x User manual
Transcript
UM10208 Philips Semiconductors Chapter 15: LPC288x UART Table 183. Interrupt Clear Enable Register (INTCE - 0x8010 1FD8) Bit Name Description Reset value 0 DCTSIEClr Writing a 1 to this bit clears the DCTSIE bit in the INTE register. - Reserved. Software should not write ones to reserved bits. - 3:1 4 THREIEClr Writing a 1 to this bit clears The THREIE bit in the INTE register. - 5 RxTOIEClr Writing a 1 to this bit clears the RTXOIE bit in the INTE register. - 6 RxDAIEClr Writing a 1 to this bit clears the RxDAIE bit in the INTE register. - 7 WakeUpIEClr Writing a 1 to this bit clears the WakeUpIE bit in the INTE register. - 8 ABEOIEClr Writing a 1 to this bit clears the ABEOIE bit in the INTE register. - 9 ABTOIEClr Writing a 1 to this bit clears the ABTOIE bit in the INTE register. - Reserved. Software should not write ones to reserved bits. - 11:10 12 BreakIEClr Writing a 1 to this clears the BreakIE bit in the INTE register. - 13 FEIEClr Writing a 1 to this clears the FEIE bit in the INTE register. - 14 PEIEClr Writing a 1 to this clears the PEIE bit in the INTE register. - 15 OEIEClr Writing a 1 to this bit clears the OEIE bit in the INTE register. - Reserved. Software should not write ones to reserved bits. - 31:16 3.26 Interrupt Enable Register (INTE - 0x8010 1FE4) Bits 15:12, 9:4, and 0 in this read-only register are 1 if the corresponding bit in INTS is enabled to cause a UART interrupt, and 0 if not. Table 184. Interrupt Enable Register Bit Name 0 DCTSIE 3:1 (INTE - 0x8010 1FE4) Description Reset value This bit is 1 if the DCTSInt bit in INTE is interrupt-enabled. 0 Reserved. The value read from a reserved bit is not defined. - 4 THREIE This bit is 1 if The THREInt bit in INTE is interrupt-enabled. 0 5 RxTOIE This bit is 1 if the RTXOInt bit in INTE is interrupt-enabled. 0 6 RxDAIE This bit is 1 if the RxDAInt bit in INTE is interrupt-enabled. 0 7 WakeUpIE This is 1 if the WakeUpInt bit in INTE is interrupt-enabled. 0 8 ABEOIE This bit is 1 if the ABEOInt bit in INTE is interrupt-enabled. 0 9 ABTOIE This bit is 1 if the ABTOInt bit in INTE is interrupt-enabled. 0 11:10 Reserved. The value read from a reserved bit is not defined. - 12 BreakIE This is 1 if the BreakInt bit in INTE is interrupt-enabled. 0 13 FEIE This is 1 if the FEInt bit in INTE is interrupt-enabled. 0 14 PEIE This is 1 if the PEInt bit in INTE is interrupt-enabled. 0 15 OEIE This bit is 1 if the OEInt bit in INTE is interrupt-enabled. 0 Reserved. The value read from a reserved bit is not defined. - 31:16 4. Architecture The architecture of the UART is shown in Figure 15–23. UM10208_1 User manual © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 01 — 5 September 2006 159 of 338
Related documents