Download EXP810 User & Installation Guide
Transcript
Electrical requirements . . . . . . . . . . . . . . . . . . . . Power and site wiring requirements for models with ac power supply and fan units . . . . . . . . . . . . . . . . . . . . . . . Power and site wiring requirements for models with dc power supply and fan units . . . . . . . . . . . . . . . . . . . . . . . Heat output, airflow, and cooling . . . . . . . . . . . . . . . . Network Equipment-Building System (NEBS) information for applicable Disk Systems . . . . . . . . . . . . . . . . . . . . . . . . Chapter 2. Installing the EXP810. Installation overview . . . . . . Handling static-sensitive devices . Preparing for installation . . . . Tools and hardware required . . Preparing the site . . . . . . Preparing the rack . . . . . Installing the support rails . . . . Installing the EXP810 into a rack . Installing a Telco bezel . . . . . iv . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 . 24 . 25 . . . . . . . . . . . . . . . . . . . . 29 29 30 30 31 31 32 32 36 38 Chapter 3. Cabling the EXP810 . . . . . . . . . . . . . . . . Enclosure ID settings . . . . . . . . . . . . . . . . . . . . Fibre channel loop and ID settings. . . . . . . . . . . . . . . . Cabling the EXP810 . . . . . . . . . . . . . . . . . . . . . Installing SFP modules . . . . . . . . . . . . . . . . . . . . Removing SFP modules . . . . . . . . . . . . . . . . . . . Handling fibre-optic cables . . . . . . . . . . . . . . . . . . Using LC-LC fibre-channel cables . . . . . . . . . . . . . . . . Connecting an LC-LC cable to an SFP module . . . . . . . . . . Removing an LC-LC fibre-channel cable . . . . . . . . . . . . Cabling rules and recommendations . . . . . . . . . . . . . . . Cabling the EXP810 to a storage subsystem . . . . . . . . . . . . EXP810 loop redundancy . . . . . . . . . . . . . . . . . . . Example of a correct redundant drive loop . . . . . . . . . . . . Intermixing the EXP810, EXP710, and EXP100 in the same drive loop . . Intermixing EXP810s with EXP710s and EXP810s in a DS4700 or DS4800 configuration . . . . . . . . . . . . . . . . . . . . . . . Cabling the ac power supply . . . . . . . . . . . . . . . . . . Cabling the dc power supply . . . . . . . . . . . . . . . . . . Single-level redundant dc cabling . . . . . . . . . . . . . . . Dual-level redundant dc cabling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 41 42 42 43 45 46 47 48 49 50 51 53 54 56 . . . . . . . . . . 60 61 62 63 64 Chapter 4. Operating the EXP810 . . . . . . Performing the DS4000 Health Check process . . Web pages . . . . . . . . . . . . . . Hardware responsibilities . . . . . . . . . Powering on the EXP810 . . . . . . . . . . Turning on the EXP810 . . . . . . . . . Firmware updates . . . . . . . . . . . . . Finding controller, storage expansion enclosure, and Troubleshooting the storage expansion enclosure . Checking the LEDs . . . . . . . . . . . . The ac power supply and fan unit LEDs. . . . The dc power supply and fan unit LEDs. . . . Front LEDs . . . . . . . . . . . . . . Rear LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 67 68 68 69 69 71 72 72 73 73 74 75 76 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 . . . . . . . . . . . . . . . . . . . . . . . . drive . . . . . . . . . . . . . . . . . . . . . . . 22 . . . . . . . . . . . . . . IBM System Storage DS4000 EXP810 Storage Expansion Enclosure: Installation, User’s and Maintenance Guide . . . . . . . . . . . . . .