Download EXP810 User & Installation Guide

Transcript
Electrical requirements . . . . . . . . . . . . . . . . . . . .
Power and site wiring requirements for models with ac power supply and
fan units . . . . . . . . . . . . . . . . . . . . . . .
Power and site wiring requirements for models with dc power supply and
fan units . . . . . . . . . . . . . . . . . . . . . . .
Heat output, airflow, and cooling . . . . . . . . . . . . . . . .
Network Equipment-Building System (NEBS) information for applicable Disk
Systems . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 2. Installing the EXP810.
Installation overview . . . . . .
Handling static-sensitive devices .
Preparing for installation . . . .
Tools and hardware required . .
Preparing the site . . . . . .
Preparing the rack . . . . .
Installing the support rails . . . .
Installing the EXP810 into a rack .
Installing a Telco bezel . . . . .
iv
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 23 . 24 . 25 .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
29
29
30
30
31
31
32
32
36
38
Chapter 3. Cabling the EXP810 . . . . . . . . . . . . . . . .
Enclosure ID settings . . . . . . . . . . . . . . . . . . . .
Fibre channel loop and ID settings. . . . . . . . . . . . . . . .
Cabling the EXP810 . . . . . . . . . . . . . . . . . . . . .
Installing SFP modules . . . . . . . . . . . . . . . . . . . .
Removing SFP modules . . . . . . . . . . . . . . . . . . .
Handling fibre-optic cables . . . . . . . . . . . . . . . . . .
Using LC-LC fibre-channel cables . . . . . . . . . . . . . . . .
Connecting an LC-LC cable to an SFP module . . . . . . . . . .
Removing an LC-LC fibre-channel cable . . . . . . . . . . . .
Cabling rules and recommendations . . . . . . . . . . . . . . .
Cabling the EXP810 to a storage subsystem . . . . . . . . . . . .
EXP810 loop redundancy . . . . . . . . . . . . . . . . . . .
Example of a correct redundant drive loop . . . . . . . . . . . .
Intermixing the EXP810, EXP710, and EXP100 in the same drive loop . .
Intermixing EXP810s with EXP710s and EXP810s in a DS4700 or DS4800
configuration . . . . . . . . . . . . . . . . . . . . . . .
Cabling the ac power supply . . . . . . . . . . . . . . . . . .
Cabling the dc power supply . . . . . . . . . . . . . . . . . .
Single-level redundant dc cabling . . . . . . . . . . . . . . .
Dual-level redundant dc cabling. . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
41
41
42
42
43
45
46
47
48
49
50
51
53
54
56
.
.
.
.
.
.
.
.
.
.
60
61
62
63
64
Chapter 4. Operating the EXP810 . . . . . .
Performing the DS4000 Health Check process . .
Web pages . . . . . . . . . . . . . .
Hardware responsibilities . . . . . . . . .
Powering on the EXP810 . . . . . . . . . .
Turning on the EXP810 . . . . . . . . .
Firmware updates . . . . . . . . . . . . .
Finding controller, storage expansion enclosure, and
Troubleshooting the storage expansion enclosure .
Checking the LEDs . . . . . . . . . . . .
The ac power supply and fan unit LEDs. . . .
The dc power supply and fan unit LEDs. . . .
Front LEDs . . . . . . . . . . . . . .
Rear LEDs . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
67
67
68
68
69
69
71
72
72
73
73
74
75
76
. . . . .
. . . . .
. . . . .
. . . . .
. . . . .
. . . . .
. . . . .
information
. . . . .
. . . . .
. . . . .
. . . . .
. . . . .
. . . . .
.
.
.
.
.
.
.
.
.
.
. 23 .
.
.
.
.
.
.
.
.
.
. .
. .
. .
. .
. .
. .
. .
drive
. .
. .
. .
. .
. .
. .
.
.
.
.
.
.
.
.
.
.
. 22 .
.
.
.
.
.
.
.
.
.
.
.
.
.
IBM System Storage DS4000 EXP810 Storage Expansion Enclosure: Installation, User’s and Maintenance Guide
.
.
.
.
.
.
.
.
.
.
.
.
.
.