Download "user manual"

Transcript
Table 7.1 Resetable Faults
Display
Meaning
Probable Causes
Undertorque Detection 2
UL4
Undertorq Det 2
The Inverter’s output current (V/f control) or the output torque (Vector conMotor was underloaded.
trol) fell below L6-05 for longer than
the time set in L6-06 and L6-04 is set to
7 or 8.
Motor Overspeed
OS
Overspeed Det
Detected when F1-03 is set to 0, 1 or 2
and A1-02 is set to 3.
Detected when F1-02 is set to 0, 1 or 2
and A1-02 is set to 3 or 6
Fix the broken/disconnected wiring.
The PG is wired incorrectly.
Fix the wiring.
Power is not supplied to the PG.
Detected when no PG (encoder) pulses
are received for a time longer than the
setting of F1-14.
Wrong brake control sequence. The
motor runs against the closed brake.
Excessive Speed Deviation
DV3
Detected when F1-04 is set to 0, 1 or 2
The load is locked.
and A1-02 is set to 3 or 6
The speed deviation is higher than the The settings of F1-10 and F1-11 are not
setting of F1-10 for a time longer than appropriate.
the setting of F1-11.
Wrong brake control sequence. The
motor runs against the closed brake.
Wrong rotation direction
Detected when the speed deviation is
higher than 30% and the torque reference and acceleration have opposite
signs.
DV6
Over Acceleration
SVE
Zero Servo Fault
Zero Servo Fault
properly.
Check the sequence and if the brake
is opened when the inverter starts to
increase the speed.
Reduce the load.
Check the mechanical system.
Check the settings of F1-10 and F111.
Check the sequence and if the brake
is opened when the inverter starts to
increase the speed.
PG wire broken
Check the PG wiring
Incorrect PG wiring
Correct the wiring
Wrong magnet position compensation Verify the PG direction and execute
value (F1-22)
an encoder offset auto tuning
The magnet position offset setting in
Wrong rotation direction
F1-22 is wrong
Detected when F1-19 is not 0, the
speed reference and motor speed have
opposite signs and the detection thresh- The load is too large
old set in F1-19 is exceeded.
An over acceleration of the car was
detected (A1-02 = 6 only)
Supply power to the PG
The acceleration time and deceleration Lengthen the acceleration time and
time are too short.
deceleration time.
The load is too large
DV4
Adjust the ASR settings in the C5
parameter group.
The PG wiring is broken.
The load is too large.
DEV
Speed Deviation
Check application/machine status
to eliminate fault.
Check the reference circuit and refThe reference was too high.
erence gain.
The motor speed feedback (U1-05)
exceeded the setting in F1-08 for a time
The settings in F1-08 and F1-09 are not Check the settings in F1-08 and F1longer than the setting of F1-09.
appropriate.
09.
PG Disconnection
PGO
PG Open
Overshooting/Undershooting occurs.
Corrective Actions
Ensure the values in L6-05 and L606 are appropriate.
Reduce the load and check the
brake
Verify the PG direction and execute
an encoder offset auto tuning
Reduce the load and check the
brake
The load is too large
Reduce the load
Magnet position offset is wrong
Check the PG direction, check F122 and perform an encoder offset
tuning.
Sheave diameter, gear ratio or roping
setting incorrect
Verify the settings of S3-13, S3-14
and S3-15.
Too short acceleration or deceleration
time.
Adjust the acceleration and deceleration times.
The torque limit is too small.
Increase the torque limit.
The motor position moved during Zero The load torque is too large.
Servo Operation.
-
7
Decrease the load torque.
Check for signal noise.
7-5