Download Manual - Equipco
Transcript
3700 Standard and 3700 Compact Sampler The 3700 Sampler is a microprocessor-based device that executes a software program stored in ROM. The program is a series of instructions that tell the microprocessor what to do in order to accomplish the various functions that the sampler must perform. In the following discussion of the hardware, the software is discussed only as is necessary to describe the operation of the circuitry. The A 12 VDC connector on the side of the control box is used to connect to an external 12 V source. A 3.75 Amp PTC device provides circuit protection. 7. Individual CMOS semiconductors and built-up printed circuit boards should always be transported in conductive packaging. Foil is satisfactory; metallic plastic bags are also available and work well. If you purchase replacement components that do not come in marked, protective packaging, do not use them. They may already be destroyed. 8. Once assembled and soldered, printed circuit boards are easily damaged by improper repair procedures. Do not attempt to remove components, particularly ICs, from printed circuit boards unless you are skilled at this procedure. You can locate and change a defective component, and the unit may still not work if excessive heat or pressure has broken the foil traces or pulled the cores from holes on the board. The 3700 Sampler contains two printed circuit boards: the main board and the pump-control board. The display module (attached to the main circuit board) also contains a small circuit board. This module is fully assembled when purchased. It does not contain any user-serviceable parts. Unless the display module is being replaced, do not disturb it. Contact Customer Service - If trouble symptoms persist and you are unable to locate the cause, call the Customer Service Department at (800) 228-4373. Main Board - P4 supplies power to the circuitry pin 1 is ground and pin 2 is 12 volts. A 5-volt switching regulator (IC U11) obtains a 5-volt rail from the 12-volt supply. Preliminary Electronics Troubleshooting Steps All of the ICs used in the 3700 Samplers are powered from the 5-volt rail. IC U11 is also used as a low-voltage detector, constantly monitoring the 12volt supply. IC U17. Isco suggests checking the following possible problem areas before attempting to service the microprocessor CPU and associated circuitry. A voltage converter, provides a -5-volt supply, which some components require. IC U8 is the microprocessor, IC U5 is the ROM, and IC U7 is the RAM. These three ICs make up the brains of the 3700 Sampler. The microprocessor executes the program stored in ROM. While executing, information (program settings, sample data, etc.) is retrieved from and stored in RAM. A 4.608 MHz crystal oscillator (Y1) sets the microprocessor’s execution speed. 1. Be sure that the supply voltage is correct. 2. Check to see that the wiring harnesses, connectors, and solder joints are in good condition. 3. Look for signs of physical damage, such as burned or broken components, overly hot components, or evidence of water damage. 4. Check for shorted or open diodes and transistors, especially driver transistors. 5. Ensure that voltage regulators working properly. 6. Check to see if there is excessive current draw in some or all of the circuitry. 7. Be sure that correct input signals are sent to the unit. 8. Check to see that the crystal oscillator is operating and at proper frequency. 9. Examine the reset circuitry to be sure that it is working properly. 10. Check lithium battery for 3 VDC output when main power is removed. The 3700 Sampler keeps track of time with a realtime clock (IC U3). Both the RAM and IC U3 are battery-backed with a lithium battery (B1). IC U1 is a switch that selects between battery and system power. Three devices allow the microprocessor to communicate with the outside world: the 2-line, 20-characters-per-line LCD, IC U9, and IC U18. The LCD facilitates communication with the user and is connected through P3. IC U13, transistor Q2, thermistor R15, and other components provide the LCD with a temperature compensated driver voltage. By providing temperature compensation, the display quality is optimized over a wide temperature range. IC U9 and IC U18 are I/O devices, which allow the microprocessor to read the keypad, sound the beeper, advance the distributor, measure pump counts, and so on. Circuit Boards The following is a general description of the 3700 Sampler electronic circuitry. While reading this description, refer to the schematic diagram (Figure 41), the case schematic diagram (Figure 43), and the pictorial views of the circuit boards (Figures 40 and 42). 127