Download Manual - Equipco

Transcript
3700 Standard and 3700 Compact Sampler
The 3700 Sampler is a microprocessor-based device
that executes a software program stored in ROM.
The program is a series of instructions that tell the
microprocessor what to do in order to accomplish
the various functions that the sampler must perform. In the following discussion of the hardware,
the software is discussed only as is necessary to
describe the operation of the circuitry. The A 12
VDC connector on the side of the control box is
used to connect to an external 12 V source. A 3.75
Amp PTC device provides circuit protection.
7. Individual CMOS semiconductors and built-up
printed circuit boards should always be transported in conductive packaging. Foil is satisfactory; metallic plastic bags are also available and
work well. If you purchase replacement components that do not come in marked, protective
packaging, do not use them. They may already
be destroyed.
8. Once assembled and soldered, printed circuit
boards are easily damaged by improper repair
procedures. Do not attempt to remove components, particularly ICs, from printed circuit
boards unless you are skilled at this procedure.
You can locate and change a defective component, and the unit may still not work if excessive
heat or pressure has broken the foil traces or
pulled the cores from holes on the board.
The 3700 Sampler contains two printed circuit
boards: the main board and the pump-control board.
The display module (attached to the main circuit
board) also contains a small circuit board. This module is fully assembled when purchased. It does not
contain any user-serviceable parts. Unless the display module is being replaced, do not disturb it.
Contact Customer Service - If trouble symptoms persist and you are unable to locate the
cause, call the Customer Service Department at
(800) 228-4373.
Main Board - P4 supplies power to the circuitry
pin 1 is ground and pin 2 is 12 volts. A 5-volt
switching regulator (IC U11) obtains a 5-volt rail
from the 12-volt supply.
Preliminary Electronics
Troubleshooting Steps
All of the ICs used in the 3700 Samplers are powered from the 5-volt rail. IC U11 is also used as a
low-voltage detector, constantly monitoring the 12volt supply. IC U17.
Isco suggests checking the following possible problem areas before attempting to service the microprocessor CPU and associated circuitry.
A voltage converter, provides a -5-volt supply,
which some components require. IC U8 is the
microprocessor, IC U5 is the ROM, and IC U7 is
the RAM. These three ICs make up the brains of
the 3700 Sampler. The microprocessor executes the
program stored in ROM. While executing, information (program settings, sample data, etc.) is
retrieved from and stored in RAM. A 4.608 MHz
crystal oscillator (Y1) sets the microprocessor’s
execution speed.
1. Be sure that the supply voltage is correct.
2. Check to see that the wiring harnesses, connectors, and solder joints are in good condition.
3. Look for signs of physical damage, such as
burned or broken components, overly hot components, or evidence of water damage.
4. Check for shorted or open diodes and transistors, especially driver transistors.
5. Ensure that voltage regulators working properly.
6. Check to see if there is excessive current draw
in some or all of the circuitry.
7. Be sure that correct input signals are sent to the
unit.
8. Check to see that the crystal oscillator is operating and at proper frequency.
9. Examine the reset circuitry to be sure that it is
working properly.
10. Check lithium battery for 3 VDC output when
main power is removed.
The 3700 Sampler keeps track of time with a realtime clock (IC U3). Both the RAM and IC U3 are
battery-backed with a lithium battery (B1). IC U1
is a switch that selects between battery and system power.
Three devices allow the microprocessor to communicate with the outside world: the 2-line, 20-characters-per-line LCD, IC U9, and IC U18. The LCD
facilitates communication with the user and is connected through P3. IC U13, transistor Q2, thermistor R15, and other components provide the
LCD with a temperature compensated driver voltage. By providing temperature compensation, the
display quality is optimized over a wide temperature range. IC U9 and IC U18 are I/O devices,
which allow the microprocessor to read the keypad,
sound the beeper, advance the distributor, measure
pump counts, and so on.
Circuit Boards
The following is a general description of the 3700
Sampler electronic circuitry. While reading this
description, refer to the schematic diagram (Figure 41), the case schematic diagram (Figure 43),
and the pictorial views of the circuit boards (Figures 40 and 42).
127