Download INSTAllATION MANUAl
Transcript
programming Option No. P117E To D8/D16 AUX header P117E 1E Description Default 1E Enable Output Expander OFF 2E Expander Output Format A & B OFF 3E Day Zone follower OFF 4E Output Exclude OFF 5E Expander Output Format C OFF 6E User Code Toggle or Pulse OFF 7E [not used] OFF 8E [not used] OFF Enable Output Expander program mode level Selecting this option enables the optional 106-011 Output Expander. Installer mode or NessComms. When this option is enabled, the AUX connector on the main board will only drive the Output Expander. Factory Default OFF: No Output Expander. When this option is disabled, the AUX header is used for the 106-013 Four Relay Board. Notes • Connect up to two Output Expander boards. Programming sequence: P117E 1E toggles the option ON and OFF OFF: No Output Expander ON: Output Expander enabled P117E 2E Expander Output Format A, B, C program mode level Use this option along with option P117E 5E to configure the output expander outputs as per the output tables. Installer mode or NessComms. Factory Default Three different combinations of outputs are available for either a single or dual output expanders. OFF Notes • The second expander plugs into the second 6-way header on the first expander. The expander closest to the panel becomes Expander 1. Programming sequence: P117E 2E toggles the option ON and OFF • The User Code outputs will follow the ON/OFF state of the User Codes 13 to 15. These outputs can be made to change via: A) Radio key. Pressing the ON button turns the output On, OFF turns it OFF. A Radio key must be programmed to a User Code 13~15 for this will operate. B) Radio keypad auxiliary key. The radio keypad auxiliary key (there are 2 auxiliary keys) must be programmed to a User Code 13~15. C) The D8x/D16x keypad using ARM - DISARM with a User Code. Enter Arm+User_Code_13~15 to turn the output on. User_Code_13~15 + E will turn the output off. Note that the USER CODE does not have to be assigned to an AREA for this to work. • If P117E 6E is ON then the ARM, DISARM buttons on Radio Keys do not change the Code13-15 outputs on the output expander. Only the AUX button works, pulsing ON the Code13-15 output for the time set by P145E. 54 OUTPUT Output Format A Output Format B Output Format C P117E 1E = ON P117E 2E = OFF P117E 5E = OFF P117E 1E = ON P117E 2E = ON P117E 5E = OFF P117E 1E = ON P117E 2E = OFF P117E 5E = ON EXPANDER 1 EXPANDER 2 (Or if using only one expander) EXPANDER 1 EXPANDER 2 (Or if using only one expander) EXPANDER 1 (Or if using only one expander) EXPANDER 2 1 Zone 1 Aux 5 Zone 1 Aux 5 Aux 5 Zone 1 2 Zone 2 Aux 6 Zone 2 Aux 6 Aux 6 Zone 2 3 Zone 3 Aux 7 Zone 3 Aux 7 Aux 7 Zone 3 4 Zone 4 Aux 8 Zone 4 Aux 8 Aux 8 Zone 4 5 Zone 5 User Code 13 Zone 5 User Code 13 User Code 13 Zone 5 6 Zone 6 User Code 14 Zone 6 User Code 14 User Code 14 Zone 6 7 Zone 7 User Code 15 Zone 7 User Code 15 User Code 15 Zone 7 8 Zone 8 Tel. Line Fail Zone 8 Tel. Line Fail Tel. Line Fail Zone 8 9 Zone 9 Aux 1 Aux 1 Zone 9 Aux 1 Zone 9 10 Zone 10 Aux 2 Aux 2 Zone 10 Aux 2 Zone 10 11 Zone 11 Aux 3 Aux 3 Zone 11 Aux 3 Zone 11 12 Zone 12 Aux 4 Aux 4 Zone 12 Aux 4 Zone 12 13 Zone 13 Arm Home Arm Home Zone 13 Arm Home Zone 13 14 Zone 14 Mains Fail Mains Fail Zone 14 Mains Fail Zone 14 15 Zone 15 Battery Fail Battery Fail Zone 15 Battery Fail Zone 15 16 Zone 16 Ext. Tamper Ext. Tamper Zone 16 Ext. Tamper Zone 16 Ness D8x / D16x DELUXE Control Panel – Installation Manual