Download lmu-tk15a4-lmu-tk15a4t_sm227.89 KB

SERVICE MANUAL
INDUSTRIAL MONITOR
LMU-TK15A4 (Without Touch Panel)
LMU-TK15A4T (With Touch Panel)
(GENERAL)
PRODUCT CODE NO.
LMU-TK15A4
1 938 102 24
LMU-TK15A4T 1 938 102 28
REFERENCE NO. SM 920009
REFERENCE NO. SM 920010
PRODUCT CODE NO.193810224
PRODUCT CODE NO.193810228
INDEX
PRECAUTIONS -----------------------------------------------------------------------------------
Page
2
1,MAIN SPECIFICATION ----------------------------------------------------------------------
3
2, TROUBLE SHOOTING ----------------------------------------------------------------------
4,5
3, MAINTENANCE
3-1 LMU-TK15A4 --------------------------------------------------------------------------- 6
3-2 LMU-TK15A4T ------------------------------------------------------------------------- 7
4, BLOCK DIAGRAM ---------------------------------------------------------------------------- 8
5, CONNECTION DIAGRAM ------------------------------------------------------------------
9
6, TABLE OF SIGNAL NAME -----------------------------------------------------------------
10,11
7, EXPLODED VIEW AND PARTS LIST
7-1 Exploded View ------------------------------------------------------------------------
12
7-2 Parts List
LMU-TK15A4 --------------------------------------------------------------------------- 13
LMU-TK15A4T ------------------------------------------------------------------------- 14
8, APPENDEX -------------------------------------------------------------------------------------
Refer to the separate user’s guide for instruction.
-1-
15
PRECAUTIONS
l
Placement precautions
Avoid placing the unit in humid or dusty places, or where it will be exposed to excessive heat
l
(direct sunlight, heaters, etc.)
Do not step on or set anything on the AC cord. DAMAGE TO THE AC CORD IS A
l
SAFETY RISK AND CAN CAUSE A FIRE.
Do not connect the unit to the same AC outlet with appliances that generate large amounts of
interference (such as heaters with thermostats, appliances with motors, etc.). It is best to use a
l
completely separate electrical outlet.
Keep the unit away from water. If water accidentally enters the unit, unplug the AC power cord
immediately. DO NOT PLUG IN THE UNIT AGAIN.
Handling precautions
l
Avoid bending, kinking or damaging the AC power cord.
l
Never insert or remove the power cord with wet hands. Also, be sure to hold cord by the plug when
l
removing it from the outlet.
Do not remove any parts that are held in place with screws. (The unit does not contain any user
serviceable items.)
Maintain standard room temperature (5oC to 40 oC, or 41oF to 104 oF) during use. Do not subject
l
l
the unit to shock or vibration. Do not move the unit while it is in use.
A rapid increase in room temperature in cool weather can cause condensation to from inside the unit.
If this occurs, wait at least 15 minutes after turning the unit on before attempting to operate it.
-2-
1. MAIN SPECIFICATION
Model Name
LMU-TK15A4T
LMU-TK15A4
Display
Panel Type
Screen Size
Pixel Pitch
Pixel Format
Brightness
Response Time
Contrast
Viewing Angle (minimum)
Back Light
Colors
Video Control
System
Input Signal
Video
Sync.Type/Level
Synchronization Horizontal
Frequencies
Vertical
Touch panel
Type
Electrical Resolution
TFT
15.0"
0.297×0.297 mm
1,024×768
250cd/m2 typ.
40ms
350 : 1 typ.
Left & Right :±70° Up : 55° Down : 65°
CCFL × 2
16.77million
Analog RGB
0.7Vp-p 75 ohm
Separate TTL
24.8k - 60.2kHz
56 - 75Hz
-
Communication
Capacitive
10bit (1,024x1,024)
Bi-directional asynchronous
RS232C serial communication
Physical
Input
Environment
Power Supply
(AC Adapter)
Video Signal
Serial
Power Supply
Operating
Temperature
Humidity
Model Name
Input
Output
Power Supply Consumption
Dimensions
Weight
Accessories
15pin mini D-Sub
-
9pin mini D-Sub
DC Jack
operating : 5° to 40°
Storage : -20° to 60°
30% - 85% RH (No Condensation)
GI40-US1225
AC115-240V 1.0A-0.55A, 50-60Hz
DC 12V 2.5A
28W max.
30W max.
5W in Energy Saving mode
385(W) x 308(D) x 46(H) mm
385(W) x 309(D) x 54(H) mm
3.7 kg
4.2 kg
AC Adapter, Power Cord, RGB
AC Adapter, Power Cord, RGB
cable, OSD control box, User's
cable, Serial cable, OSD control
Guide
box, Touch Ware CD-ROM,
User's Guide
-3-
2. TROUBLESHOOTING
Check the following for troubles of LCD monitor.
No.
1
2
3
Symptom
Check Points
Treatments
Check AC outlet, AC cord, DC
1 Is the Power "ON" to a LCD Monitor ? Jack and Power switch for a
LCD monitor
Check the Power for a
2 Is the Power "ON" to a Computer ?
Computer
Check the connection of a signal
3 Is a signal cable connected securely ?
cable
Be out of standing by condition,
4 Is a computer standing by ?
by operating to a computer
Disconnected a signal cable ? or Bent Ensure the connection of a
5
a terminal pin ?
signal cable
Replace an AC Adapter with the
6 Is an AC Adapter defective?
new one
No Picture with Back
Is the wire harness between Inverter
Check the connection of wire
light OFF
7 PCB and a LCD module secured firmly
harness
?
Is the wire harness between main PCB Check the connection of wire
8
and Inverter PCB secured firmly ?
harness
Is the wire harness between main PCB Check the connection of wire
9
and DC IN PCB secured firmly ?
harness
Replace a LCD module with the
10 Is the LCD module defective ?
new one
Replace an Inverter unit with the
11 Is the Inverter unit defective ?
new one
Is the display circuit on main PCB
Replace the main PCB with the
12
defective ?
new one
Is the Power Supply circuit on main
Replace the main PCB with the
13
PCB defective ?
new one
Be out of standing by condition,
1 Is a computer standing by ?
by operating to a computer
Press any key or touch the
Is a screen saver programming
2
mouse, to end the screen saver
running ?
No Picture with
program
Back light ON
Is the computer's signal timing not
Adjust the computer's signal
3
agreeable to the LCD's specification ? timing, if possible
Is the Image Processing circuit on
Replace the main PCB with the
4
main PCB defective ?
new one
Is the wire harness between main PCB Ensure the connection of wire
1
and LCD module secured firmly ?
harness
White/Grey on
Replace a LCD module with the
whole
2 Is the LCD module defective ?
new one
screen(Nothing on
screen)
Is the Image Processing unit circuit on Replace the main PCB with the
3
main PCB defective ?
new one
A It is possible to treated by end-user
B It might be possible to treat by end-user in some case.
C It must be treated by Professional Technical Staff
-4-
Class
A
A
A
A
B
C
C
C
C
C
C
C
C
A
A
B
C
C
C
C
No.
Symptom
Check Points
Treatments
Is the adjustment for screen performed
Adjust the screen correctly
correctly ?
Is the output level on image from a
Check the specification of a
2 computer not agreeable to LCD's
computer
specification ?
Set the size of screen
3 Is the size of screen set correctly ?
again(refer to User's Manual for
computer)
Is the adjustment for screen performed
1
Adjust the screen correctly
correctly ?
Check the connection of a signal
2 Is a signal cable connected securely ?
cable
1
4
5
Screen's display
range is incorrect
Screen is distorted
3 Is a sigil cable extended ?
Is the output level on image from a
4 computer not agreeable to LCD's
specification ?
Is the Image Processing circuit on
5
main PCB defective ?
6
Part of colors
(R/G/B) is not
displayed. Black line
appears in vertically
A
B
A
A
A
Don't extend a signal cable
A
Check the specification of a
computer
B
Replace the main PCB with the
new one
Check the connection of a signal
1 Is a signal cable connected securely ?
cable
Is the connection between main PCB Ensure the connector of wire
2
and a LCD module securely ?
harness
Is the Image Processing circuit on
Replace the main PCB with the
3
main PCB defective ?
new one
A It is possible to treated by end-user
B It might be possible to treat by end-user in some case.
C It must be treated by Professional Technical Staff
-5-
Class
C
A
C
C
3. MAINTENANCE
3-1 LMU-TK-15A4
(1)
Disassembling the major components
Cabinet
1. Unscrew to secure the cabinet(8-position)
2. Pull the cabinet upward to remove it
(2)
LCD module
1. Unscrew to secure the LCD module(4-position)
2. Pull the LCD module up, and pull two connectors out from inverter unit
3. Disconnect two cables from the main PCB
(3)
Inverter Unit
1. Unscrew to secure the Inverter Unit(4-position)
2. Disconnect the cable from the main PCB
(4)
Main PCB
1. Pull a RGB signal cable out
2. Unscrew to secure the main PCB(5-position)
3. Disconnect the cables on the main PCB(6-position)
(one cable has already been disconnected)
/ two connectors from LCD module
/ one connector from the Switch PCB
/ one connector from the VR PCB
/ one connector from the DC-IN PCB
/ one connector from the Inverter PCB
4. Unscrew to secure the bracket for RGB connector(2-position)
(5)
Connector PCB
1. Unscrew to secure the connector PCB(2-position)
2. Disconnect the cable from the main PCB
(6)
VR PCB
1. Unscrew to secure the VR PCB(2-position)
2. Disconnect the cable from the main PCB
(7)
DC-IN PCB
1. Unscrew to secure the DC-IN PCB(2-position)
2. Disconnect two cables, one is from power switch and another one is
From the main PCB
(8)
Power Switch
1. Remove the power switch, while pressing the hock of the power switch
-6-
3-2 LMU-TK-15A4T
(1)
Disassembling the major components
Cabinet
1. Unscrew to secure the cabinet(8-position)
2. Pull the cabinet upward to remove it
(2)
LCD Panel
1. Unscrew to secure the LCD panel(4-position)
2. Pull the LCD panel and touch panel up,
and pull two connectors out from inverter unit
3. Disconnect two cables from the main PCB
4. Unscrew to secure the earth terminal(1-position)
5. Disconnect the cable on the main PCB
6. Disconnect the cable on the touch controller PCB
(3)
Inverter Unit
1. Unscrew to secure the inverter unit(4-position)
2. Disconnect the cable from the main PCB
(4)
Main PCB
1. Pull a RGB signal cable out
2. Unscrew to secure the main PCB(5-position)
3. Disconnect the cables on the main PCB(7-position)
(two cables has already been disconnected)
/ two connectors from LCD panel
/ one connector from the Switch PCB
/ one connector from the VR PCB
/ one connector from the DC-IN PCB
/ one connector from the Inverter PCB
/ one connector from the Touch Controller PCB
4. Unscrew to secure the bracket for RGB connector(2-position)
(5)
Touch Controller
1. Unscrew to secure the touch controller PCB(2-position)
2. Disconnect a serial cable
(6)
Serial Cable (Connector and Cable with bracket)
1. Unscrew to secure the bracket for serial cable(2-position)
(7)
Connector PCB
1. Unscrew to secure the connector PCB(2-position)
2. Disconnect the cable from the main PCB
(8)
VR PCB
1. Unscrew to secure the VR PCB(2-position)
2. Disconnect the cable from the main PCB
(9)
DC-IN PCB
1. Unscrew to secure the DC-IN PCB(2-position)
2. Disconnect two cables, one is from power switch and another one is from the main PCB
(10)
Power Switch
1. Remove the power switch, while pressing the hook of the power switch
-7-
-8-
Red
Green
Blue
Hsync
Vsync
DB15
TXD
RXD
DB 9
VIDEO
PRE-AMP
SAMPLING
PLL
Main PCB (SANDDUNE2)
CRC
For LMU-TK150A4T only
TM
TM
POWER SUPPLY
CHEETAH3
8-bit, 135-MHz ADCs
PLLS
Enhanced IP scaling with line buffers
Anti-smear, anti-color bleed Þlters
Edge enhancement Þlter
SmartSet processing
SureSync processing
Frame rate conversion
OSD with memory
Gamma correction look-up table
Color enhancement/dithering
PWMs
TFT panel timing engine
MICRO CONTROLLER
TOUCHSCREEN CONTROLLER
PANEL
CONTROL
ROM
CAPACITIVE
TOUCHSCREEN SENSOR
XGA LCD PANEL
TFT
4. BLOCK DIAGRAM
CTS
TXD
RTS
RXD
N.C.
RTS
RXD
TXD
CTS
GND
CN7
1
6
2
7
3
8
4
9
5
N.C.
Touch Screen
Controller
1
6
2
7
3
8
4
9
5
1
2
3
4
5
6
7
JP1
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
- 10 12
11
10
9
8
7
6
5
4
3
2
1
LL
UL
LR
UR
BACK
VCC(+12V)
CHASSIS GND
POWER GND
N.C.
N.C.
N.C.
N.C.
DSR
DCD
GND
DTR
5
9
4
8
3
7
2
6
1
D-SUB 9PIN
VGA
8
15
7
14
6
13
5
12
4
11
3
10
2
9
1
GND
DDCLK
GND
VSYNC
GND
HSYNC
GND
DDDA
N.C.
N.C.
BLUE
GND
GREEN
N.C.
RED
8
15
7
14
6
13
5
12
4
11
3
10
2
9
1
P6
Mini D-SUB 15pin
P8
SERIAL PORT
Personal
Computer
1
2
P9
CN502
Connector
P.C.B
P2
CN501
VR1
External OSD
Switch
CN6
P5
P10
Brightness Volume
P.C.B
GND
DCLK
GND
DENA
GND
VD
GND
HD
GND
NC
GND
BO7
BO6
BO5
BO4
GND
BO3
BO2
BO1
BO0
GND
GO7
GO6
GO5
GO4
GND
GO3
GO2
GO1
GO0
GND
RO7
RO6
RO5
RO4
GND
RO3
RO2
RO1
RO0
VCC
VCC
TEST
TEST
TEST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
CN201
CN202
P7
TFT 15-inch Liquid
Crystal Display
Analogue Interface P.C.B
SANDDUNE2
1
2
3
4
5
6
7
8
1
2
3
N.C
N.C
1
2
Capacitive
GND
DDCLK
GND
VSYNC
GND
HSYNC
GND
DDDA
N.C.
N.C.
BLUE
GND
GREEN
N.C.
RED
1
2
3
4
5
MENU
SEL
DOWN
UP
GND
N.C
N.C
N.C
VR1
VRC
VR2
1
2
3
4
5
+12V
GND
1
2
J201
DC IN
P.C.B
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Touch Screen
1
2
3
4
5
1
2
GND
BE7
BE6
BE5
BE4
GND
BE3
BE2
BE1
BE0
GND
GE7
GE6
GE5
GE4
GND
GE3
GE2
GE1
GE0
GND
RE7
RE6
RE5
RE4
GND
RE3
RE2
RE1
RE0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
P3
1
2
3
4
5
Power Switch
HOT1
COLD1
HOT1
COLD1
1
2
3
4
5
AC
Adapter
+12V
GND
VR1
VR2
ON(=5V)
CN1
CN2
1
2
3
N.C.
SINV-75
AC
Plug
Inverter
Unit
CN3
1
2
3
N.C.
5. Connection Diagram
6. TABLE OF SIGNAL NAME
Symbol
RED
GREEN
BLUE
DDDA(ID1)
HSYNC
VSYNC
DDCK(ID3)
BE7
BE6
BE5
BE4
BE3
BE2
BE1
BE0(EVEN)
GE7
GE6
GE5
GE4
GE3
GE2
GE1
GE0(EVEN)
RE7
RE6
RE5
RE4
RE3
RE2
RE1
RE0(EVEN)
DCLK
DENA
VD
HD
BO7
BO6
BO5
BO4
BO3
BO2
BO1
BO0
GO7
GO6
GO5
GO4
GO3
GO2
GO1
Signal Name
RED/Analog Video Signal
GREEN/Analog Video Signal
BLUE/Analog Video Signal
DDC Data
Horizontal Synchronizing Signal
Vertical Synchronizing Signal
DDC Data Clock
BLUE Data[MSB]-Even
BLUE Data
BLUE Data
BLUE Data
BLUE Data
BLUE Data
BLUE Data
BLUE Data[LSB]-Even
GREEN Data[MSB]-Even
GREEN Data
GREEN Data
GREEN Data
GREEN Data
GREEN Data
GREEN Data
GREEN Data[LSB]-Even
RED Data[MSB]-Even
RED Data
RED Data
RED Data
RED Data
RED Data
RED Data
RED Data[LSB]-Even
Data Clock
Data Enable
Vertical Synchronizing Signal
Horizontal Synchronizing Signal
BLUE Data[MSB]-Odd
BLUE Data
BLUE Data
BLUE Data
BLUE Data
BLUE Data
BLUE Data
BLUE Data[LSB]-Odd
GREEN Data[MSB]-Odd
GREEN Data
GREEN Data
GREEN Data
GREEN Data
GREEN Data
GREEN Data
- 10 -
Location
P6-1
P6-2
P6-3
P6-12
P6-13
P6-14
P6-15
P10-2
P10-3
P10-4
P10-5
P10-7
P10-8
P10-9
P10-10
P10-12
P10-13
P10-14
P10-15
P10-17
P10-18
P10-19
P10-20
P10-22
P10-23
P10-24
P10-25
P10-27
P10-28
P10-29
P10-30
P9-2
P9-4
P9-6
P9-8
P9-12
P9-13
P9-14
P9-15
P9-17
P9-18
P9-19
P9-20
P9-22
P9-23
P9-24
P9-25
P9-27
P9-28
P9-29
Notes
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
Symbol
GO0
RO7
RO6
RO5
RO4
RO3
RO2
RO1
RO0
TEST
TEST
TEST
+12V
VR1,2
ON=5V
VR1,2
VRC
MENU
SEL
DOWN
UP
LED R
LED G
Signal Name
GREEN Data[LSB]-Odd
RED Data[MSB]-Odd
RED Data
RED Data
RED Data
RED Data
RED Data
RED Data
RED Data[LSB]-Odd
Test Signal Out(*)
Test Signal Out(*)
Test Signal Out(*)
for Output Voltage (+)
for Contrast Volume
for Back-Light Control
Brightness Control
Brightness Control
Menu Key Input
Select Key Input
Down Key Input
Up Key Input
LED/RED, Control Signal
LED/GREEN, Control Signal
Location
P9-30
P9-32
P9-33
P9-34
P9-35
P9-37
P9-38
P9-39
P9-40
P9-43
P9-44
P9-45
P3-1
P3-3,4
P3-5
P5-1,3
P5-2
P2-1
P2-2
P2-3
P2-4
P2-6
P2-8
* : This terminal must be opened at System-side.
TouchScreen Controller
(for LMU-TK15A4T only)
RTS
RXD
TXD
CTS
DCD
DTR
GND
DSR
GND
UR
LR
UL
LL
Repuest To Send
Receive Data
Transmit Data
Clear To Send
Data Carrier Detect
Data Terminal Ready
Signal ground
Data Set Ready
Chassis (earth) ground
Upper right (UR) corner
Lower right (LR) corner
Upper left (UL) corner
Lower left (LL) corner
JP1-1
JP1-2
JP1-3
JP1-4
NC
NC
NC
NC
NC
JP2-9
JP2-10
JP2-11
JP2-12
- 11 -
Notes
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
POLARITY +
H: Light ON
7. EXPLODED VIEW AND PARTS LIST
7-1 Exploded View
- 12 -
CAUTION
Parts marked as Are very important to secure safety.
In case of replacement, it is required to use designted parts for safety.
7-2. Parts List
7-2-1 LMU-TK15A4
REF NO.
1
17
11
3
6
12
16
15
2
13
7
9
10
8
PART No.
OUTER
632 890 7397
INDIVIDUAL
632 861 5414
632 889 7827
632 889 7834
661 000 9587
632 862 2696
632 603 0998
632 298 2376
632 607 4824
632 567 2588
ACCESSORY
632 890 8363
632 890 8370
CABINET1
661 001 5564
632 892 1010
CHASSIS
661 001 5526
CHASSIS ELC.
661 001 5540
661 001 5588
661 001 5595
661 001 5557
632 872 9494
661 001 5601
632 890 5010
PC BOARD 1
661 001 5632
PC BOARD 3
661 001 5649
PC BOARD 4
661 001 5663
PC BOARD 6
661 001 5670
DESCRIPTION
Q'ty
OUTER CARTON
1
PAD, TOP
ACCESSORY CASE
PAD
PAD, CORNER
POLYETHYLENE BAG, 400X550
POLYETHYLENE BAG, 130X500
POLYETHYLENE BAG, 120X320
POLYETHYLENE BAG, L 180X270
POLYETHYLENE BAG, 200X300
1
1
1
8
1
1
1
1
1
INSTRUCTION MANUAL, ENGLISH
INSTRUCTION MANUAL, GERMAN
1
1
TOP LID ASS'Y
RATING PLATE
1
1
BOTTOM LID ASS'Y, 15A4
1
LIQUID CRYSTAL DIS. ASS'Y, 15.0"
DC-AC INVERTER ASS'Y
POWER SWITCH ASS'Y
AC ADAPTER ASS'Y
VGA CABLE, 1.5M
FFC ASS'Y
REMOTE CONTROLLER ASS'Y
1
1
1
1
1
1
1
PW BOARD ASS'Y, MAIN
1
PW BOARD ASS'Y, VR
1
PW BOARD ASS'Y, DC-IN
1
PW BOARD ASS'Y, CN
1
- 13 -
NOTES
FOR MONITOR
FOR AC ADAPTER
FOR CONTROLL BOX
FOR USER'S GUIDE
FOR RGB CABLE
CAUTION
Parts marked as Are very important to secure safety.
In case of replacement, it is required to use designted parts for safety.
7-2-2 LMU-TK15A4T
REF NO.
1
17
11
4
6
12
16
5
15
14
2
13
7
9
10
8
PART No.
OUTER
632 890 7397
INDIVIDUAL
632 861 5414
632 889 7827
632 889 7834
661 000 9587
632 862 2696
632 603 0998
632 298 2376
632 607 4824
632 567 2588
632 607 4824
ACCESSORY
632 890 8363
632 890 8370
632 867 2325
CABINET1
661 001 5571
632 892 1003
CHASSIS
661 001 5519
CHASSIS ELC.
661 001 5533
661 001 5588
661 001 5595
661 001 5557
661 001 5625
632 835 1060
632 866 8397
661 001 5618
632 890 5010
PC BOARD 1
661 001 5632
PC BOARD 3
661 001 5649
PC BOARD 4
661 001 5663
PC BOARD 6
661 001 5670
DESCRIPTION
Q'ty
NOTES
OUTER CARTON
1 Stamp T
PAD, TOP
ACCESSORY CASE
PAD
PAD, CORNER
POLYETHYLENE BAG, 400X550
POLYETHYLENE BAG, 130X500
POLYETHYLENE BAG, 120X320
POLYETHYLENE BAG, L 180X270
POLYETHYLENE BAG, 200X300
POLYETHYLENE BAG, L 180X270
1
1
1
8
1
1
1
1
1
1
INSTRUCTION MANUAL, ENGLISH
INSTRUCTION MANUAL, GERMAN
CD-ROM DISK, TOUCHWARE
1
1
1
TOP LID ASS'Y
RATING PLATE
1
1
BOTTOM LID ASS'Y, 15A4T
1
LIQUID CRYSTAL DIS. ASS'Y, TOUCH
DC-AC INVERTER ASS'Y
POWER SWITCH ASS'Y
AC ADAPTER ASS'Y
SERIAL CONTROLLER ASS'Y
CABLE, VGA
SERIAL CABLE, 1.8M
FFC ASS'Y
REMOTE CONTROLLER ASS'Y
1
1
1
1
1
1
1
1
1
PW BOARD ASS'Y, MAIN
1
PW BOARD ASS'Y, VR
1
PW BOARD ASS'Y, DC-IN
1
PW BOARD ASS'Y, CN
- 14 -
FOR MONITOR
FOR AC ADAPTER
FOR CONTROLL BOX
FOR USER'S GUIDE
FOR RGB CABLE
FOR SERIAL CABLE
APPENDIX
Version
of Firmware
The Version of Firmware is displayed on screen.
Turn the Power Switch to ‘OFF’. While pressing of the [SELECT] ( [ENTER] ) button, turn the
Power Switch to ‘ON’.
- 15 -