Download RVV NG Vender with 5-button Programming

SECTION 3: Vender Programming
The display will show the current four-digit hour and
minute setting, in 24-hour format. The hour setting
will be flashing to indicate that it can be modified.
Pressing <up> or <down> will increase or decrease
the hour. Pressing <enter> will stop the hour from
flashing and cause the minutes to blink indicating
they can be modified. Pressing <up> or <down>
will increase or decrease the minutes value. Pressing
<enter> again will save the displayed setting and
return you to the “Start Hour” prompt. Pressing
<exit> while in editing mode will return to the “Start
Hour” prompt without saving changes. Use <up> to
proceed to the next prompt, “Stop Time.”
Set Discounts
If <enter> is pressed at the “Set Discounts” prompt, the
controller will enter the discount control mode. Using
<up> or <down>, the user can cycle through the various
discount control settings (“Enable Discounting,” “Start
Time,” “Stop Time,” “Discount Selections,” and “Discount
Amount”). If <exit> is pressed, the controller will return
to the “Set Discounts” prompt. Use <up> to proceed to the
next prompts, “Selection Blocking 1,” “Selection Blocking
2,” and “Selection Blocking 3.”
•
•
Enable Discounting
Upon first entry into “Set Discounts”, the controller
will display “Enable Discounting X”. If <enter>
is pressed at “Enable Discounts X”, “X” will begin
flashing indicating that it can be edited. If X = 1,
discounts will be enabled. This means that active
selections will be discounted by the programmed
discount amount during the programmed time blocks.
Discounted vend prices of zero or less may be
allowed, but no credit will ever be given in return. If
X = 0, discounting will be disabled. Pressing <up>
or <down> will allow the user to toggle “X” between
“1” and “0”. Pressing <enter> will save the displayed
setting and return you to the non-editable “Enable
Discounting” prompt. Use <up> to proceed to the
next prompt, “Start Time.”
Start Time
If <enter> is pressed at the “Start Time” prompt, the
controller will enter the start discounting time setting
routing. Upon entry into this routine, the display will
show the first of the two start time setting modes,
“Start Day” or “Start Hour.” Pressing <up> or
<down> will cycle between the two. Pressing <exit>
at this point will return to the “Start Time” prompt
without saving any changes.
•
Stop Time
If <enter> is pressed at the “Stop Time” prompt,
the controller will enter the stop discounting time
setting routing. Upon entry into this routine, the
display will show the first of the two stop time setting
modes, “Stop Day” or “Stop Hour.” Pressing <up> or
<down> will cycle between the two. Pressing <exit>
at this point will return to the “Stop Time” prompt
without saving any changes.
If <enter> is pressed at the “Stop Day” prompt, the
controller will enter the day of the week setting
routine. The display will show “YY X”, where “YY”
is the day of the week (Monday, Tuesday, Wednesday,
Thursday, Friday, Saturday, Sunday, or Every Day)
and “X” is either “1” or “0”. Pressing <up> or
<down> will cycle through the days of the week. If
<enter> is pressed at the “YY X” prompt, “X” will
flash, indicating that it can be changed. Pressing <up>
or <down> will toggle “X” between “1” (enabled) and
“0” (disabled). Pressing <enter> again will save the
displayed setting and return you to the non-flashing
“YY X” prompt. Pressing <exit> will return to the
“Stop Day” prompt.
If <enter> is pressed at the “Start Day” prompt,
the controller will enter the day of the week setting
routine. The display will show “YY X”, where “YY”
is the day of the week (Monday, Tuesday, Wednesday,
Thursday, Friday, Saturday, Sunday, or Every Day)
and “X” is either “1” or “0”. Pressing <up> or
<down> will cycle through the days of the week. If
<enter> is pressed at the “YY X” prompt, “X” will
flash, indicating that it can be changed. Pressing <up>
or <down> will toggle “X” between “1” (enabled) and
“0” (disabled). Pressing <enter> again will save the
displayed setting and return you to the non-flashing
“YY X” prompt. Pressing <exit> will return to the
“Start Day” prompt.
If <enter> is pressed at the “Start Hour” prompt, the
controller will enter the start time setting routine.
30
Royal Vision Vender NG 5-button Service and Parts Manual