Download Microtek Wireless Ethernet Systems Network Card User Manual

OPERATIONS MANUAL
MiniLink® Wireless Ethernet Systems
MicroTek Electronics, Inc.
25691 Atlantic Ocean Drive, Suite B-3; Lake Forest, CA 92630
Information Hotline 888-36-MICRO
www.microtekelectronics.com
IMPORTANT SAFETY INSTRUCTION
For your protection, please read and observe all safety instructions before operating this system and keep this sheet and
any additional instructions for future reference.
INSTALLATION & USE
OBSERVE WARNINGS: All warnings in the operating instructions should be carefully followed. Do not make any
modifications to the WEM, PIM, or any other MicroTek electronic device, as the unit will no longer comply with FCC
regulations and therefore cancel its warranty.
WATER AND MOISTURE: The Wireless Ethernet Modules used in this system are weatherproof provided they are
installed in accordance to the mounting details listed on page 7 (or included dish manual for the 30-mile systems).
However, further protection or housing is suggested for harsh environments, as moisture damage voids its warranty (as
described on page 22). The Power Injection Modules used in this system are NOT weatherproof. None of the modules
in this system are waterproof and should never be submerged. Severe electrical shock, personal injury or damage to the
equipment may result.
POWER SOURCE: Connect the equipment to a power source only of the type described on the operating instructions or
as marked on the equipment. Excessive or insufficient amperage or voltage can cause extended trouble-shooting or even
damage that could negate its warranty. The power supplies’ cable should not be modified/extended due to the ability to
use up to 300 feet of power over Ethernet (see pg 7, part D). In addition, Ethernet cable running from the PIM to the
WEM should be kept separated from high-voltage cables and/or transformers.
ATTACHMENTS: Use only MicroTek supplied or recommended Power Injection Modules, Power Supplies, CAT5
Cables and weather seals and plugs.
WHEN NOT IN USE: Unplug the power if the equipment is left unattended or unused for long periods of time or
during lightning storms.
REPLACEMENT PARTS: When replacement parts are required, use only replacement parts specified by MicroTek
Electronics, Inc. Unauthorized substitutions may result in damage to the system and will void the warranty.
FCC-Required Information Federal Communications Commission
Radio Frequency Interference Statement for Class A Digital Devices
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
frequencies. Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
This equipment is designed to be professionally installed exclusively for fixed point-to-point applications. These products
must be controlled due to radio frequency power output levels emitted with special consideration given to antenna
placement as it relates to human exposure. Compliance is the responsibility of the installer and user.
Radio Frequency Interface Statement
This equipment has been tested and found to comply with the limits for an intentional radiator, pursuant to Part 15,
Subpart C of the FCC Rules. This equipment generates, uses, and can radiate radio frequency energy. If not installed and
used in accordance with the instructions, it may cause interference to radio communications. The limits are designed to
provide reasonable protection against such interference in a residential situation. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause interference to radio or television
reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna of the affected radio or television.
•
Increase the separation between the equipment and the affected receiver.
•
Connect the equipment and the affected receiver to power outlets on separate circuits.
•
Consult the dealer or an experienced radio/TV technician for help.
Shielded cables must be used with this unit to ensure compliance with Class A FCC limits. Changes or modifications to
this unit not expressly approved by the party responsible for compliance could void the users authority to operate the
equipment. Changes or modifications not expressly approved by MicroTek could void the users authority to operate the
equipment.
-(i)-
FCC Output Power Restrictions
The FCC does not require licensing to implement this device. License-free operation in the industrial, scientific, and medical
band is documented in FCC Rules Part 15.247. It is the responsibility of the individuals designing and implementing the
radio system to assure compliance with any pertinent FCC Rules and Regulations. This device must be professionally
installed.
Exposure to Radio Frequency Fields
The Minilink 5.8WES is designed to operate at 5.8 GHz with up to 50 Watts EIRP maximum transmit power. This level of
RF energy is above the Maximum Permissible Exposure (MPE) levels specified in FCC OET65:97-01. The following
precautions must be taken during installation of this equipment:
•
The installed antenna must not be located in a manner that allows exposure of the general population to the direct
beam path of the antenna at a distance less than 1 Meter. Installation on towers, masts, or rooftops not accessible
to the general population is recommended; or
•
Mount the antenna in a manner that prevents any personnel from entering the area within 1 Meter from the front of
the antenna.
•
It is recommended that the installer place radio frequency hazard warnings signs on the barrier that prevents
access to the antenna.
•
During installation and alignment of the antenna, do not stand in front of the antenna assembly.
•
During installation and alignment of the antenna, do not handle or touch the front of the antenna.
These simple precautions must be taken to prevent general population and installation personnel from exposure to RF
energy in excess of specified MPE levels.
Industry Canada Restrictions
This device is in compliance with the applicable sections of the Industry Canada RSS-210 Spectrum Management and
Telecommunications Radio Standard Specification that governs Low Power License-Exempt Radiocommunication Devices.
Specifically, the output EIRP of this device relative to antenna gain is factory set to ensure compliance with section
6.2.2(q1)(iv)(g).
In addition, it is noted for all users that high power radars are allocated as primary users (meaning they have priority) of the
5250-5350 MHz and 5650-5850 MHz frequency bands and these radars could cause interference and/or damage to LELAN
devices such as are covered by this manual.
Environmental Limitations of FCC License-Free Wireless Devices
MicroTek products are engineered to the highest standards and designed to work in a variety of wireless applications and
environments. A wireless environment includes not only a particular site in which the product is installed but also the
installation itself and any extra materials that might be necessary to complete the wireless project. Due to the fact that
environments and installations differ from site to site, MicroTek cannot control the variables required to ensure an ideal
environment. Therefore, it is not possible to guarantee a successful application based on a drawing, application note, quote
or other type of material that MicroTek may provide. Should a quote, drawing, etc. be made available, it is based on the
performance of the WES product in an ideal environment with clear line-of-sight, absence of 5 GHz interference and/or
frequency multi-path reflection. Therefore, MicroTek cannot be held responsible should the products not operate as desired
or should additional products be required to complete a project. In addition, should a particular environment restrict the
usage of the MiniLink WES in any way, MicroTek offers a thirty (30) day return policy from date of original shipment (see
page 3).
- ( ii ) -
FCC REGULATORY ALERT
Regulatory Alert
As of July 20, 2007, a new FCC regulation has gone into effect which impacts operators of
the U-NII band in the United States. As a result of this regulatory change, several MicroTek
products are affected. The new FCC regulation impacts the sale of wireless equipment in the
5.25-5.35 GHz band. The regulation states that all devices imported and marketed after the
July 20th, 2007 deadline must support radar detection as specified by the FCC in the 5.255.35 GHz band.
MicroTek Electronics Product Changes
To comply with FCC regulation, MicroTek has disabled the 5.25-5.35 GHz band. The
following products are still available but will only support operation in the 5.725-5.85 GHz
ISM band.
ML WES-2500
ML WES-2-4
ML WAP
ML WAPOM
ML WSU
ML WSUP
ML WSUOM
ML WES-D
ML WES-OD
ML WES-D1-2
MicroTek is currently working on the firmware change necessary to comply with the new
FCC regulations which require Dynamic Frequency Selection (DFS) and Transmit Power
Control (TPC) for operation in the 5.25-5.35 GHz band.
How Does the FCC Regulation Affect the WES User?
If one WES System is in use and there are no plans to add to the wireless project then it
might not affect you at all. However, if you are using two or more systems then you may
need to change frequencies according to the available channels. Multiple WES systems set to
channels 0, 1 or 2 (all unavailable 5.2/5.3 GHz frequencies) will all be defaulted to channel 3
(available 5745 MHz). The next available frequency in sequence would be channel 4 (5765
MHz). Channels 3 through 7 are all individual frequencies but channels 0-2 are not available.
- ( iii ) -
INDEX
SECTION
PAGE #
IMPORTANT SAFETY INSTRUCTIONS, FCC NOTICE ---------------- ( i )
RADIO FREQUENCY EXPOSURE, INDUSTRY CANADA ------------- ( ii )
IMPORTANT FCC REGULATORY NOTICE------------------------------- ( iii )
QUICK START GUIDE ----------------------------------------------------------- 2
PRE-INSTALLATION REMINDER, RETURN POLICY ----------------- 3
WEM DESCRIPTION ------------------------------------------------------------- 4
FRONT, REAR & SIDE VIEWS -------------------------------------------------- 4 - 5
PIM DESCRIPTION --------------------------------------------------------------- 5
TOP, RIGHT & LEFT SIDE VIEWS ---------------------------------------------- 5
WES CONNECTION DIAGRAM ----------------------------------------------- 6
WEM INSTALLATION & OPERATION ------------------------------------- 6 - 8
SELECT CHANNEL & POLARITY SELECT ---------------------------------- 6
MOUNT WEM & CONFIGURE CABLE ---------------------------------------- 7
CONNECT WEM & ESTABLISH LINK ---------------------------------------- 8
ADVANCED OPERATION ------------------------------------------------------ 8 - 16
WEB BROWSER INTERFACE --------------------------------------------------- 8
LOGIN & STATUS – DEVICE STATUS----------------------------------------- 9 – 11
STATUS – ASSOCIATION LISTS------------------------------------------------- 12
STATUS – STATISTICS ------------------------------------------------------------ 13
BASIC – WIRELESS & ETHERNET SETTINGS------------------------------ 14 – 15
ADVANCED – ADMIN/SYSTEM/FIRMWARE------------------------------- 16 – 17
SYSTEM INSTALLAION NOTES ------------------------------------------------ 18
WEM SPECIFICATIONS -------------------------------------------------------- 19 - 20
TROUBLE SHOOTING ----------------------------------------------------------- 21
FAQ------------------------------------------------------------------------------------- 22
WARRANTY ------------------------------------------------------------------------- 23
COVERED PRODUCTS
PART #
ML WAP
ML WAPOM
ML WSUOM
ML WSU
ML WSUP
ML WSUDI
ML WEM
ML WEMP
ML WEM-30
DESCRIPTION
MiniLink 5.8 GHz Wireless Host / Access Point - Directional
MiniLink 5.8 GHz Wireless Host / Access Point - Omni-directional
MiniLink 5.8 GHz Wireless Client / Subscriber Unit - Omni
MiniLink 5.8 GHz Wireless Client / Subscriber Unit - Standard
MiniLink 5.8 GHz Wireless Client / Subscriber Unit – 6” x 6”Patch
MiniLink 5.8 GHz Wireless Client / Subscriber Unit – 18” Dish
MiniLink 5.8 GHz Wireless Ethernet Module
MiniLink 5.8 GHz Wireless Ethernet Module w/ 6” patch antenna
MiniLink 5.8 GHz Wireless Ethernet Module – 18” Dish
-1-
QUICK START PROCEDURES
MicroTek Electronics, Inc. recommends that all equipment be bench tested before being installed onsite.
This test will ensure the equipment is functioning properly.
IMPORTANT: SEE NEW FCC REGULATORY ALERT ON PAGE “( iii )”
WIRELESS ETHERNET MODULE SETUP
1. Remove the Host and Client from the box, select frequency via the rotary switch at the side of
the unit. (Factory set to channel 0 unless otherwise noted) The channels of each set of
Host/Clients must be matched for the radios to communicate with each other. For multiconnect devices, each Client must be set to the same channel as the Host that it will be
connected to. If connecting more than one Client to a Host, please see the advanced
operation section of this manual for setup.
2. Mount the Client at the remote location. Point the Client as accurately as possible to the point
where Host will be mounted.
3. Remove the Power Injection Modules (PIMs) from the box and determine where they will be
located for each Host/Client. Total distance between a Host/Client and connected Ethernet
device cannot exceed 300 feet (100m). The PIMs can be located anywhere along the 300 feet
of CAT5 cable. Connect a standard CAT5 straight through patch cable to the “Ethernet Out”
port on each PIM to its corresponding Host/Client. “Ethernet In” port on each PIM should be
connected to its respective Ethernet device using a standard CAT5 straight through patch
cable. A crossover cable may be needed depending on your Ethernet device.
4. Connect the included power supplies to the “Power In” port on the PIMs and plug the
transformers into a standard 110VAC outlet. If the Ethernet devices on each end are
connected, powered up and aimed correctly, the “Link Activity”, “Power” and “Signal Level”
LEDs will illuminate. If the Ethernet device is not connected the “Power” LED and “Signal
Level” LEDs only will illuminate. If the “Signal Level” LED is flashing, reposition the
modules to achieve max signal strength. For multi-connect applications, each Client will
show a solid green light when connected to a Multipoint Host. A flashing green LED on the
Multipoint Host Access Point will indicate the number of Client Subscriber Units to which it
is connected.
Note: If a dish is used with the system, assemble the dish and mount the Client/Host in the dish as described in
the dish installation instructions. Then position the dish and connect the CAT5 cable as described above.
Trouble Shooting: If the signal level indicator is not fully lit, video does not appear on the
screen or you are having other operational difficulties, please visit the trouble-shooting
section on page 21 of the operations manual or contact MicroTek toll free at (888) 366-4276
for technical assistance.
-2-
PRE-INSTALLATION REMINDERS
The information on the Quick Start Guide is intended for ease of use and application, the following
reminders will help to ensure your satisfaction with MicroTek products and service.
1. Read through this manual before bench testing and installation
2. A helpful IP Address Locating tool is available to download from our website at
http://www.microtekelectronics.com/softwaretools.htm. Download the Locator.exe tool.
3. Perform a bench test incorporating all components of the application
4. Install your MiniLink Wireless Ethernet System
5. Toll-free technical assistance is available Monday through Friday (8-5pm PST) at 888-3664276
MICROTEK ELECTRONICS RETURN POLICY
MicroTek Electronics wireless products come with a 2-year limited warranty, (see the last page for
warranty information) unless otherwise specified. In addition to the 2-year warranty, products may
be returned within thirty (30) days of shipment provided the products are in like new condition and in
the original packaging. Contact your MicroTek Electronics dealer or distributor to obtain an
authorization to return the merchandise for credit.
Return authorizations for repair can be sent directly to Microtek Electronics with a valid RA number.
Call MicroTek Electronics to obtain an RA number for repair.
-3-
MINILINK WIRELESS ETHERNET SYSTEM (WES)
The MiniLink WES is a plug and play CAT5/Ethernet cable replacement device. It operates in the
5.8 GHz U-NII bands on 5 non-overlapping channels. The WES system enables a wide variety of
IP cameras, DVRs, encoders/decoders and web servers to be used across wireless line-of-sight links
in ranges of 500 feet to 30 miles. The system operates independent of any network it may be
connected to.
MINILINK WIRELESS ETHERNET MODULE (WEM)
WEM DESCRIPTION
A. FRONT VIEW
B. REAR VIEW
NOTE: Mount
Host/Client so that
Vertical Ethernet
Port is at bottom and
use weatherproof
caps and plugs for
outdoor use as
described on pg 7.
5
1 2 3
4
1. LINK ACTIVITY LED
Indicates that an Ethernet cable connection between powered Ethernet device & Host or
Client has been established.
2. POWER LED
Indicates the Host or Client has power.
3. SIGNAL LEVEL LED
Indicates the signal strength level between Host/Client. On the MP Host AP, indicates the
number of connected Clients. Note: This is not an indication of available throughput.
4. ETHERNET PORT
Standard RJ-45 connector. Outdoor use- must be weather protected with supplied strainrelief positioned so the connector is at bottom of the case. Weatherproof strain-relief plug
should be tight enough so that it is snug on the cable but not to restrict cable movement.
5. CHANNEL SELECT
Rotary switch for channel selection, factory set to Channel 0. Switch is positioned on the
side of the gray case behind the weatherproof plug. Plug must be resealed after channel change.
C. BOTTOM VIEW
1
D. SIDE VIEW
3
2
3. ROTARY CHANNEL SELECT
SWITCH (REMOVE WEATHERPROOF PLUG)
Shows switch settings for channels 0 – 7.
1. ETHERNET PORT
Standard RJ-45 Connector
2.
MOUNTING HOLES
(3) ¼ - 20 mounting holes. Two vertical holes
for dish L-bracket (ML WES-12 / ML WES-30
/ ML WSUDI). Far right hole for black swivel mount.
-4-
REPLACE (RESEAL) WEATHERPROOF PLUG
AFTER CHANNEL SELECT CHANGE AND
POWER CYCLE
POWER INJECTION MODULE (PIM)
Note: The Power Injector Modules are not weatherproof units and must be protected from moisture.
PIM DESCRIPTION
A. TOP VIEW
2
1
3
1. ETHERNET IN – Connect to Ethernet device
2. POWER IN – 12-20 VDC Center Positive
3. ETHERNET OUT – Connect to Host/Client
B. RIGHT SIDE VIEW
1. POWER LED – Lit when power is on
2. ETHERNET OUT – Connect to Host/Client
3. POWER IN – Connect to Power Supply
1 2
3
C. LEFT SIDE VIEW
1. ETHERNET IN – Connect to Ethernet device
1
-5-
WES CONNECTION DIAGRAMS
The following wiring schemes represent the configurations that have been tested and verified by MicroTek
Electronics based on typical Ethernet wiring solutions. Other wiring configurations could be possible based on
the application. A bench test is recommended to verify the designs below.
A. POINT-TO-POINT SYSTEM
ML ENC shown
1. Client Wireless Ethernet Module
2. Host Wireless Ethernet Module
3. Cat5 Connection to Ethernet Device
4. Cat5 Connection to Ethernet Device
ML DEC shown
5. Power Injection Module Ethernet Out to Client
6. Power Injection Module Ethernet Out to Host
7. Antenna separation of less than max system range, clear
line-of-sight
B. MULTI-CONNECT SYSTEM
ML ENC shown
ML DEC shown
ML DEC shown
ML ENC shown
1. Client Wireless Ethernet Module
2. MP Host Wireless Ethernet Module
3. Cat5 Connection to Ethernet Device
4. Cat5 Connection to Ethernet Device
5. Power Injection Module Ethernet Out to Client
6. Power Injection Module Ethernet Out to Host
7. Antenna separation by 90 Degrees; less than max system
range, clear line-of-sight.
8. 4-(or more)-RJ-45-Port Switch (Not a MicroTek product)
Note: The Ethernet/IP device connects to the “Ethernet In” RJ45 Ethernet port on the PIM. Depending on the
Ethernet/IP device you are using, a crossover cable may be needed. No cable connection from Host/Client to
Ethernet device should exceed 300 feet (100m).
WEM INSTALLATION & OPERATION
A. SELECT CHANNEL
Locate and remove the ½ inch diameter plug at the side of the Host/Client. Select the channel
the system will operate on. Each Host/Client pair or group must share the same channel to
communicate properly. Replace the ½ inch diameter plug after the channel has been
selected.
Note: Power to the Host/Client must be cycled for the unit to recognize a new channel.
-6-
WEM INSTALLATION & OPERATION (cont’d)
B. MOUNT DIRECTIONAL HOST/CLIENT
Mount the Host/Client with the
Directional WEM
included wall/pole mount
B-1
bracket and hardware. Connect
the black mounting assembly with
adjustment swivel to mounting
L-shaped bracket with the ¼ - 20 button
head screw. Connect the unit to the
mounting assembly using the ¼-20
mounting hole in the case.
Position the Host and point
it in the direction of the Client (or viceversa) and tighten the swivel mount.
Lock in the antenna upon a solid
green Signal Level LED on the Client side.
The Host may flash if it is a multi-connect Host.
B-2
NOTE: The WEM antenna must be mounted as depicted above (Fig B-1 & B-2) to preserve its weatherproof
capability. The RJ-45 port must be protected by the port plug and positioned underneath to prevent moisture
pooling. Tighten weatherproof strain-relief so that it is snug, however, the cable should be able to move.
C. MOUNT OMNI-DIRECTIONAL HOST (IF APPLICABLE)
Due to the orientation of the MiniLink Omni-directional Host when mounted, the unit must be
kept inside a weatherproof housing. If the Weather Enclosure was purchased from MicroTek
then it will come with pole/wall mounting hardware and instructions.
D. CONFIGURE CABLE
Determine the length of CAT5 cable that will be needed and where the PIM will be located. The
total cable length from the radio to the Ethernet device cannot exceed 300 feet, however, the
PIM can be located anywhere along the 300 feet of cable. The PIM and power supply are not
weather proof and must be placed indoors or in an environmental enclosure. On the Host or
Client end, feed the CAT5 cable through the supplied weatherproof connector. Crimp an RJ45
CAT5 connector on the end of the cable and configure as a straight-through patch cable.
The Ethernet standard straight-through cable configurations used must be configured to one
of the two Ethernet standards (568-A or 568-B) in order for the WES system to operate
correctly. Any deviation from one of the two standard configurations can lead to undesired
activity so make sure your cables are configured as shown in one of the drawings below:
568-B
568-A
8
1
Orange/White 1
Solid Orange 2
Green/White 3
Solid Blue 4
RJ-45
Connector
5 Blue/White
6 Solid Green
7 Brown/White
8 Solid Brown
Green/White 1
Solid Green 2
Orange/White 3
Solid Blue 4
RJ-45
Connector
5 Blue/White
6 Solid Orange
7 Brown/White
8 Solid Brown
- Drawings shown with gold pins facing up and RJ-45 clip in rear (clip not shown)
- If 568-B is configured on end of a CAT5 cable and 568-A is configured on the other end, that configuration
would be a standard crossover cable.
-7-
WEM INSTALLATION & OPERATION (cont’d)
E. CONNECT HOST/CLIENT
Connect the cable to the Host/Client. Slide the cable jacket up to the base of the connector.
Slide the weatherproof connector over the cable jacket and screw it into the Host/Client and
tighten. Tighten the clamping nut until the CAT5 cable is sealed in the connector. Check the
antenna positioning and make sure the Power and Link Activity LEDs are on. The Link Activity
indicator, amber LED, will only illuminate if an Ethernet source device is connected and
powered up, and the red LED will verify power is being sent over the Ethernet cable. See
drawing B-2 (page 7).
F. ESTABLISH LINK
Follow above steps, A through E, for both ends of the link to be established. After both ends
have been installed and powered up, the green Signal Level LED will illuminate. A solid green
LED indicates the radios are communicating at a maximum throughput standard rate of up to 20
Mbps. If the green LED is flashing, the units are communicating at a level less than max signal
strength. If this occueD iLEDi97e csEignsds of
B. MULTI-CONNECT SYSTEMS (cont’d)
If you ordered a complete system with multiple Client SUs, they have been pre-configured with
IP addresses as follows:
ML
WES
Modules
Unit 1
Unit 2
Unit 3
Unit 4
Unit 5
ML WES
Serial
Number
05618*
05619*
05620*
05621*
05622*
ML WES
IP Address
Host AP, Client SU or
Point to Point
192.168.1.200
192.168.1.201
192.168.1.202
192.168.1.203
192.168.1.205
WES-2500 HOST**
WES-2500 CLIENT**
WAP HOST**
WSU CLIENT**
WSU CLIENT**
Channel
0
0
0
0
0
*Actual serial numbers will be different
**Actual firmware setting may be different
Note: The lowest serial number of the Client you received is pre-configured with IP address
192.168.1.201. The next higher sequential serial number of the Clients that you received will have an IP
address of 192.168.1.203, 205, 207 etc. If you ordered an additional Client separate from your original
order, the default address will be 192.168.1.201. The IP address in this additional unit will need to be
changed manually to the next available IP address before installation. An IP address-numbering table is
included in the SYSTEM INSTALLATION NOTES section of this manual on page 18. On that table,
you can track IP address changes and other notes about your specific application.
•
•
A software tool is available for free download online on MicroTek Electronics’ website at
www.microtekelectronics.com/softwaretools.htm that will assist in locating the IP addresses of
the Host and Client. This tool can also be used as a diagnostic tool or to make alignment easier.
Select the first program listed (locator.exe) and run from a laptop while connected to the
“Ethernet In” of the PIM on either the Host or Client end.
The green LED on a multi-connect Host AP will flash to indicate the number of Client units
connected to it. The Client’s green LED should remain solid.
WEB PAGES
A. LOGIN
The default password for each Host and Client is admin
Note: The password is case sensitive.
-9-
WEB PAGES (cont’d)
B. STATUS – DEVICE STATUS
1. POINT-TO-POINT HOST AP
The Device Status page provides the details of how the Single-Point Host is configured. The
Access Point Name can be changed on the “Admin” page under the ADVANCED tab but the
SSID cannot change. The updated firmware version is as shown: 7.06. One of the two jumper
settings may be “on” depending on the range of the system.
- 10 -
B. STATUS – DEVICE STATUS (cont’d)
2. MULTI-CONNECT HOST AP
The Device Status page provides the details of how the Multipoint Host is configured.
3. CLIENT SU
The Device Status page provides the details of how the Client is configured.
- 11 -
WEB PAGES (cont’d)
C.
STATUS – HOST/CLIENT ASSOCIATION LISTS
1. POINT-TO-POINT AND MULTI-CONNECT HOST
RSSI=
Received
Signal
Strength
Indicator.
The Client List page of the Host AP shows the MAC address(s) of the paired or grouped Client SU(s)
that are connected to the Host AP. For Point-to-Point systems, one MAC address will be shown. For
Multi-connect systems, the Host AP will show all of the Client SU MAC addresses currently
connected. The
page will also
show the Mode,
Rate and RSSI
communication
information for
each connected
Client SU.
Rate= This is
a snapshot of
the rate in
Megabits/sec
of the last
packet as it
crossed the
link*
2. CLIENT
The Host AP List page shows the MAC address(s) and SSID of APs that the Client can see. It shows
the Frequency, Mode, Encryption Method and RSSI communication information. If an unknown SSID
appears, the Client is noticing another 802.11a non-proprietary AP within distance and frequency
range of the unit. This is designed to inform the user of frequencies that are occupied by other nonproprietary 802.11a devices so as to transmit using a different available frequency. This is a useful
connection tool but it is not a comprehensive frequency analysis for the environment.
* The Rate as shown
on these web page
snap-shots do not
account for roughly
60% of over-head
required to operate
the system.
- 12 -
WEB PAGES (cont’d)
D. STATUS – STATISTICS
The Statistics page will indicate the number of transmitted and received data packets versus the
number of dropped packets.
- 13 -
WEB PAGES (cont’d)
E.
BASIC - WIRELESS
The wireless page is used for enabling Super mode. The Super mode combines adjacent
channels to provide up to 50+ Mbps of throughput. The channels available in Super mode are: 4
and 6 only. If another channel is selected, Super mode will not be enabled. To enable Super
mode, click the arrow in the drop
down box and select “Super A
without Turbo” (30+ Mbps) or
“Super A with Static Turbo” (50+
Mbps). Each Host/Client in your
system will need to have this feature
enabled independently.
To change frequencies from the
firmware (must start with
remote side first):
1. Click on pull down menu
next to “Channel Switch
Override”
2. Select desired frequency
3. Click “Save” and follow
reboot process
4. Click on “Status” New
Frequency Selection is
shown next to “Rotary
Switch Position.” Page may
need to be refreshed to see
this configuration. Current frequency will match on the Client information page if the Host AP
is connected.
Encryption Method Default:
WPA is the highest grade of encryption available in this system and is enabled at the factory as the
default. WPA2, AES and password are the default selections. After updating the settings as desired,
click save to update the WEM. Please note that paired or grouped WEMs must have the same settings
to operate correctly.
- 14 -
F. BASIC – ETHERNET
1. NETWORK SETTINGS
The Network Settings page is used for changing the IP Address, Subnet Mask and or Default Gateway
of the Host or Client.
- 15 -
WEB PAGES (cont’d)
G. ADVANCED – ADMINISTRATION
This section of the Advanced tab is used for changing the password and other administration
services for the Host or Client.
H. ADVANCED – SYSTEM
To reboot the system and/or bring it to its default settings, visit the system page of the Advanced
tab.
- 16 -
WEB PAGES (cont’d)
I. ADVANCED – FIRMWARE
This page is used to flash firmware upgrades should it be necessary to do so.
- 17 -
SYSTEM INSTALLATION NOTES
A. SYSTEM LOCATION
1. Address: _________________________________________________________
2. Contact: _________________________________________________________
3. Phone Number: ___________________________________________________
B. IP ADDRESS AND SERIAL NUMBERING TABLE FOR CUSTOM APPLICATIONS
Site #1
Device
WEM #1 (point-to-point applications)
WEM #2 (point-to-point applications)
Host AP WEM
Client SU WEM #1
Client SU WEM #2
Client SU WEM #3
Client SU WEM #4
Client SU WEM #5
Client SU WEM #6
Site #2
Device
WEM #1 (point to point applications)
WEM #2 (point to point applications)
Host AP WEM
Client SU WEM #1
Client SU WEM #2
Client SU WEM #3
Client SU WEM #4
Client SU WEM #5
Client SU WEM #6
Serial Number
IP Address
Serial Number
IP Address
C. NOTES: ______________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
If you have any questions regarding the advanced setup of the MiniLink Wireless Ethernet System,
please contact MicroTek’s Technical Assistance at 888-366-4276 (Monday through Friday 8-5pm
PST) or online at www.microtekelectronics.com
- 18 -
WEM SPECIFICATIONS
RF Modules
RF SECTION
Power Output
Transmitting Frequency
Channel Capacity
Modulation
Latency
Sensitivity
Polarization
Antenna Type & Gain
Beam Width
Data Throughput Rate
FCC ID
Industry Canada
MANAGEMENT
Interface
Frequency Selection
Web Browser Interface
Access Method
Protocols Used
MECHANICAL
Physical
Dimensions
Weight
POWER
Power Requirements
Power Method
50 W EIRP @ 5.8 GHz (maximum)
5.725 – 5.825 GHz (U-NII-3 / ISM)
5 non-overlapping channels
5.8 GHz Band - 5745, 5765, 5785, 5805, 5825
OFDM
<10 milliseconds
-82 dBm for maximum data rate
Linear, vertical only
Omni, 2.5 dBi
Small patch, 7.8 dBi @ 5.8 GHz
6x6 patch, 16.7 dBi @ 5.8 GHz
Small patch in 18” dish, 24 dBi @ 5.8 GHz
Omni-360°, Small patch-90°, 6x6” patch-24° & 18” dish-8°
Up to 20 Mbps - standard mode, 50+ Mbps – Super Mode
(2 channels maximum available for Super Mode)
JRRWES
4887A-WES
10/100 Base T, half/full duplex, rate auto negotiated (802.3
compliant)
Rotary switch – chans 0 – 7 or through software (see pg 13)
User ID/Password, Super Mode, IP Address, WPA2 AES
and WEP Encryption
Time division duplexing/Time division multiple access
(TTD/TDMA)
IPV4, UDP, TCP, ICMP, Telnet, HTTP, FTP, SNMP
Network Management HTTP
Environmental, sealed, billet aluminum, powder coated
housing with UV stabilized PVC radome
3.6” x 3.6” x 1.75”
15.2 oz
Connector
Cable Specifications
12 - 20 VDC @ 3 W (Reverse voltage protected)
Power-over-Ethernet (PoE) via power injector module
(“mid-span” compliant – pins 4,5 positive – pins 7,8 ground)
RJ45 – in and out of power injection box
100 Meters (328 Feet) on 24 AWG CAT-5 cable
ENVIRONMENTAL
Humidity
Operating Temperature
95% non-condensing
-20F to +150F
- 19 -
WEM SPECIFICATIONS (cont’d)
Power Injection Module
MECHANICAL
Physical
Dimensions
Weight
Interface
POWER
Power Requirements
Power-over-Ethernet (PoE)
Plastic housing, not weatherproof
2.6” x 2.6” x 1.1”
2.5 oz
2 – RJ45 connectors
Indicator
Connectors
12 VDC 500 mA (wall transformer supplied)
PoE “mid-span” compliant (pins 4,5 positive – pins 7,8
ground)
LED - red
DC Jack 2.5 mm x 5.5 mm center positive, 2 – RJ45
ENVIRONMENTAL
Humidity
Operating Temperature
95% non-condensing
-20F to +150F
System Ranges
POINT-TO-POINT SYSTEMS_______
Up to 2500 Feet
Integral directional patch antennas on both WEMs
Up to 2 Miles
Integral directional 6 x 6 13-dBi patch antennas on both
Up to 12 Miles
Integral directional 6 x 6 13-dBi patch antenna on the Host
with integral directional patch antenna in 25 dBi dish
antenna on the Client
Up to 30 Miles
Integral directional patch antennas on both WEMs mounted
in 25 dBi dish antennas
Distance specifications assume an optimal environment (see pg ii for details)
MULTI-CONNECT SYSTEMS
Up to 500 Feet
Up to 1300 Feet
Up to 2500 Feet
Up to 1 Mile
Up to 6 Miles
Integral omni-directional patch antennas on both the Host
AP WEM & Client SU WEM
Integral omni-directional patch antenna on the Host AP
WEM & integral directional patch antenna(s) on the Client
SU WEM(s)
Integral directional patch antenna on the Host AP WEM &
Client SU WEM(s)
Integral directional patch antenna on the Host AP WEM &
integral directional 6 x 6 13-dBi patch antenna(s) on the
Client SU WEM(s)
Integral directional patch antenna on the Host AP WEM &
Client SU WEM(s) – Client SU WEM(s) mounted in 25 dBi
dish antenna(s)
Distance specifications assume an optimal environment (see pg ii for details)
*For product improvement, design and specifications are subject to change without notice.
- 20 -
TROUBLE SHOOTING
PROBLEM
No Link Activity
No Signal Level LED or
Flashing Signal Level
LED
All three solid LEDs but
no picture or picture
drops out after a period
of time
No Green Signal Level
LED (When using the
ML WES-30 or ML
WES-12)
SUGGESTION
1. No power from connected device–make sure the connected
Ethernet/IP device is powered.
2. Check all cables and connectors. If the tester shows that all
wires are making contact, check the entire length of cable
for kinks, cuts, tears or any other cable hindrances.
3. Make sure the cable run between the WEM and Ethernet
device is no longer than 300 feet.
4. Make sure the cables being used are straight through (568-B
or A configured (see page 7)) and all cable connectors are
attached properly.
5. If using an Ethernet hub or fast switch, try a crossover cable
between the switch and the Power Injector Module.
1. Check line-of-sight of the WEMs. Verify the WEMs are
aimed properly. You should have clear, wide-open line of
sight between the WEM modules.
2. Change channels; cycle power.
3. Verify sufficient voltage into each PIM.
Note: The Host AP WEM green signal level LED will flash indicating
the number of Client SU WEMs it is communicating with. This is
normal for this device and should not be confused as lack of signal
strength. The green LED on the Client SU WEM should be solid if
the Client SU in order to communicate with the Host AP at a full
signal strength.
1. Check video at the camera
2. Check wiring into encoders or decoders
3. Try changing channels; cycle power. An uninterruptible
power supply (UPS) may be required and is suggested.
4. Connect one WEM directly into a PC or laptop and verify
that the IP address is accessible. Check the other WEM(s)
the same way, then verify that each IP address is accessible
over the wireless link into a PC/laptop.
5. Verify the connected Ethernet/IP device is configured
correctly. If in use, encoders and decoders must be paired
up correctly.
1. Verify wide-open line-of-sight
2. Re-angle your dish antenna in a downward angle until both
LEDs are solid green.
3. Mount the dish(es) higher above ground level and/or above
any obstruction.
If you have tried the trouble shooting steps above and the system is still not working correctly, please
contact MicroTek at 888-366-4276, Monday through Friday, between the hours of 8:00AM and
5:00PM Pacific Time. One of our technicians will work with you to rectify the problem over the
phone.
Thank you,
MicroTek Electronics, Inc.
- 21 -
FAQ
Q. Which unit is the transmitter and which is the receiver?
A. WES systems are bi-directional so it is not critical which of the units is mounted at the receive
location (and vice-versa). Typically, however, the ‘Host’ is located at the receive end and the
‘Client’ is at the transmit location.
Q. How can I tell whether I received the point-to-point WES system versus the point-tomultipoint WES system?
A. There are a few ways to tell which system you have:
1. Each system box is sealed and labeled with the manufacturer’s model number. Point-tomultipoint systems have the following model numbers: ML WES-D, ML WES-OD, ML
WES-D1-2, ML WES-D6 or single units: ML WAP, ML WAPOM, ML WSUOM, ML
WSU, ML WSUP or ML WSUDI
2. The green Signal Level LED on the Access Point Host (point-to-multipoint systems)
will flash to indicate the number of connected Subscriber Client Units with which it is
communicating.
3. If the system box is labeled as: ML WES-2500, ML WES-2-4, ML WES-12 or ML
WES-30, then the system is a point-to-point system.
Q. Why is one unit labeled as “Host” and the other labeled as “Client”?
A. The latest Version of the WES firmware enables the WEMs to communicate as one Host
with either one only or multiple Client, or subscribing, units. A Host unit is only able to
communicate with a Client and will not communicate wirelessly with another Host.
Q. What is the Locator Program?
A. A software program is available that will locate IP addresses of individual WES modules
connected as a system. This program is helpful in case the internal web browser of the WEMs
cannot be accessed. Visit the support section of our website at:
http://www.microtekelectronics.com/softwaretools.htm to download this program.
Q. Is it possible to add cameras (or Ethernet devices) to my existing Wireless Ethernet System?
A. The total amount of data that can be transmitted over the wireless system is 20 Mbps
(Megabits per second) per channel in standard mode (and 50+ Mbps in super mode). As long as
there is useable bandwidth available “over-the-air” in your configuration, more systems can be
added to an existing WES system. There are multiple options to do this depending on the
environment and application. Contact MicroTek technical support or sales at 888-366-4276
(Weekdays 8am – 5pm PST) or e-mail at your leisure to [email protected] for more
information.
Q. What is “super mode”? And, when should super mode be used?
A. Super mode combines bandwidth of adjacent channels to provide 50+ Mbps of throughput.
However, enabling this mode limits the number of channels that are available for transmission (2
channels available: 4 & 6). This mode is ideal for multiple cameras transmitting over one WES
system or to maximize throughput in a networking application.
- 22 -
WARRANTY INFORMATION
MicroTek Electronics extends the following LIMITED WARRANTY to the original
owner/purchaser of this product as follows:
- Two years from the date of initial sale for all wireless products.
- One year from the date of initial sale for all encoder and decoder products.
1) If, within the specified warranty period, this product, or any part or portion thereof,
shall prove upon examination by MICROTEK, to be defective in material or
workmanship, MICROTEK will repair or replace such part or portion at MICROTEK’s
option. The warranty period on the repaired or replaced part or portion of this product
shall be limited to the unexpired term of the original warranty. The buyer shall be
responsible for all shipping and transportation of the product to MICROTEK for any
performance under this warranty.
2) Conditions and Exceptions:
a) Any accident to this product, any misuse or abuse, alternation, use in modified
form, or any attempt to repair this product shall void this warranty. These
conditions to the warranty include, but are not limited to, incorrect power
connections, physical damage due to mechanical shock, exposure to moisture, and
circuit modification.
b) SHOULD THIS PRODUCT PROVE DEFECTIVE FOLLOWING PURCHASE,
THE BUYER, NOT THE MANUFACTURER, DISTRIBUTOR, OR RETAILER,
ASSUMES THE ENTIRE COST OF ALL SERVICING OR REPAIR, EXCEPT
AS OTHERWISE PROVIDED BY THE TERMS OF THIS WARRANTY.
c) FOR BREACH OF ANY WRITTEN OR IMPLIED WARRANTY ON THIS
PRODUCT, THE BUYER IS LIMITED TO THE FOLLOWING DAMAGES. (1)
THE COST OF LABOR TO REPAIR OR REPLACE DEFECTIVE PARTS OR
PORTIONS OF THIS PRODUCT, AND (2) THE COST OF THE REPAIRED OR
REPLACE PARTS OR PORTIONS OF THIS PRODUCT.
d) NO OTHER EXPRESSED OR IMPLIED WARRANTIES HAVE BEEN MADE
OR WILL BE MADE ON BEHALF OF MICROTEK WITH RESPECT TO THE
SALE, REPAIR, INSTALLATION, OPERATION, OR REPLACEMENT OF
THIS PRODUCT. MICROTEK DISCLAIMS ANY IMPLIED WARRANTY OF
MERCHANTABILITY OF THIS PRODUCT OR ITS FITNESS FOR ANY
PURPOSE, AND THE BUYER AGREES THAT THIS PRODUCT IS SOLD “AS
IS” AND THAT THE ENTIRE RISK OF QUALITY AND PERFORMANCE OF
THIS PRODUCT IS WITH THE BUYER, EXCEPT AS OTHERWISE
PROVIDED BY THE TERMS OF THIS WARRANTY.
e) Some states/jurisdictions do not allow exclusions or limitations of incidental or
consequential damages, or limitations on how long an implied warranty lasts, so the
above exclusions or limitations may not apply to you.
3) Contact your dealer regarding return authorization for out of warranty repairs and any
further product information.
MicroTek Electronics, Inc.
25691 Atlantic Ocean Drive, Suite B3, Lake Forest, CA 92630
Information Hotline 888-36-MICRO
www.microtekelectronics.com
- 23 -