Download Mitsubishi Electric PLA-RP100AA Service manual

OC335--1.qxp
05.8.5 5:05 PM
Page 1
SPLIT-TYPE, HEAT PUMP AIR CONDITIONERS
SPLIT-TYPE, AIR CONDITIONERS
August 2005
No. OC335
SERVICE MANUAL
Indoor unit
[Model names]
[Service Ref.]
PLA-RP35AA.UK
PLA-RP50AA.UK
PLA-RP60AA.UK
PLA-RP71AA.UK
PLA-RP100AA.UK
PLA-RP125AA.UK
PLA-RP140AA.UK
PLA-RP35AA
PLA-RP50AA
PLA-RP60AA
PLA-RP71AA
PLA-RP100AA
PLA-RP125AA
PLA-RP140AA
NOTE:
• This manual describes only
service data of the indoor
units.
PLH-P35AAH.UK
PLH-P50AAH.UK
PLH-P60AAH.UK
PLH-P71AAH.UK
PLH-P100AAH.UK
PLH-P125AAH.UK
PLH-P140AAH.UK
PLH-P35AAH
PLH-P50AAH
PLH-P60AAH
PLH-P71AAH
PLH-P100AAH
PLH-P125AAH
PLH-P140AAH
CONTENTS
1. REFERENCE MANUAL ······································2
2. SAFETY PRECAUTION···································2
3. PART NAMES AND FUNCTIONS ···················6
4. SPECIFICATIONS ············································9
5. NOISE CRITERION CURVES ························14
6. OUTLINES AND DIMENSIONS ·····················16
7. WIRING DIAGRAM············································17
8. REFRIGERANT SYSTEM DIAGRAM ··················18
9. TROUBLESHOOTING ···································19
10. DISASSEMBLY PROCEDURE ······················35
11. PARTS LIST ···················································38
Model name
indication
INDOOR UNIT
ON/OFF
TEMP
TEMP.
WIRELESS REMOTE
CONTROLLER
ON/OFF
WIRED REMOTE
CONTROLLER
OC335--1.qxp
1
05.8.5 5:05 PM
Page 2
REFERENCE MANUAL
1-1. OUTDOOR UNIT’S SERVICE MANUAL
Service Manual No.
Service Ref.
PUHZ-RP35/50/60/71/100/125/140VHA
PUHZ-RP100/125/140YHA
PUHZ-RP200/250YHA
OC334
PU(H)-P·VGAA.UK
PU(H)-P·YGAA.UK
SUZ-KA·VA.TH
OC336
MXZ-8A140VA
MXZ-8A140VA1
OC316
OC338
OC322
1-2. TECHNICAL DATA BOOK
Manual No.
Series (Outdoor unit)
PUHZ-RP·VHA(-A)
PUHZ-RP·YHA(-A)
PU(H)-P·VGAA.UK
PU(H)-P·YGAA.UK
2
OCS01
OCS02
SAFETY PRECAUTION
CAUTIONS RELATED TO NEW REFRIGERANT
Cautions for units utilising refrigerant R407C
Do not use the existing refrigerant piping.
Use liquid refrigerant to charge the system.
The old refrigerant and lubricant in the existing piping
contains a large amount of chlorine which may cause the
lubricant deterioration of the new unit.
If gas refrigerant is used to seal the system, the composition
of the refrigerant in the cylinder will change and performance
may drop.
Use “low residual oil piping”
Do not use a refrigerant other than R407C.
If there is a large amount of residual oil (hydraulic oil, etc.)
inside the piping and joints, deterioration of the lubricant
will result.
If another refrigerant (R22, etc.) is used, the chlorine in the
refrigerant may cause the lubricant deterioration.
Store the piping to be used during installation
indoors with keep both ends sealed until just
before brazing.
(Store elbows and other joints in a plastic bag.)
If dust, dirt, or water enters the refrigerant cycle,
deterioration of the oil and compressor trouble may result.
Use a vacuum pump with a reverse flow check valve.
The vacuum pump oil may flow back into the refrigerant
cycle and cause the lubricant deterioration.
Ventilate the room if refrigerant leaks during
operation. If refrigerant comes into contact with
a flame, poisonous gases will be released.
Use ESTER , ETHER or HAB as the lubricant to
coat flares and flange connection parts.
If large amount of mineral oil enter, that can cause
deterioration of refrigerant oil etc.
2
OC335--1.qxp
05.8.5 5:05 PM
Page 3
[1] Cautions for service
·After recovering the all refrigerant in the unit, proceed to working.
·Do not release refrigerant in the air.
·After completing the repair service, recharge the cycle with the specified amount of
liquid refrigerant.
[2] Refrigerant recharging
(1) Refrigerant recharging process
1Direct charging from the cylinder.
·R407C cylinder are available on the market has a syphon pipe.
·Leave the syphon pipe cylinder standing and recharge it.
(By liquid refrigerant)
Unit
Gravimeter
(2) Recharge in refrigerant leakage case
·After recovering the all refrigerant in the unit, proceed to working.
·Do not release the refrigerant in the air.
·After completing the repair service, recharge the cycle with the specified amount of
liquid refrigerant.
[3] Service tools
Use the below service tools as exclusive tools for R407C refrigerant.
No.
1
Tool name
Specifications
Gauge manifold
·Only for R407C.
·Use the existing fitting SPECIFICATIONS. (UNF7/16)
·Use high-tension side pressure of 3.43MPa·G or over.
2
Charge hose
·Only for R407C.
·Use pressure performance of 5.10MPa·G or over.
3
Electronic scale
4
Gas leak detector
·Use the detector for R134a or R407C.
5
Adapter for reverse flow check.
·Attach on vacuum pump.
6
Refrigerant charge base.
7
Refrigerant cylinder.
·For R407C
·Top of cylinder (Brown)
·Cylinder with syphon
8
Refrigerant recovery equipment.
3
OC335--1.qxp
05.8.5 5:05 PM
Page 4
CAUTIONS RELATED TO NEW REFRIGERANT
Cautions for units utilising refrigerant R410A
Use new refrigerant pipes.
Do not use refrigerant other than R410A.
In case of using the existing pipes for R22, be careful with
the followings.
· For RP100, 125 and 140, be sure to perform replacement operation before test run.
· Change flare nut to the one provided with this product.
Use a newly flared pipe.
· Avoid using thin pipes.
If other refrigerant (R22 etc.) is used, chlorine in refrigerant can cause deterioration of refrigerant oil etc.
Make sure that the inside and outside of refrigerant piping is clean and it has no contamination
such as sulfur hazardous for use, oxides, dirt,
shaving particles, etc.
In addition, use pipes with specified thickness.
Use a vacuum pump with a reverse flow check
valve.
Vacuum pump oil may flow back into refrigerant cycle and
that can cause deterioration of refrigerant oil etc.
Use the following tools specifically designed for
use with R410A refrigerant.
The following tools are necessary to use R410A refrigerant.
Gauge manifold
Charge hose
Gas leak detector
Torque wrench
Contamination inside refrigerant piping can cause deterioration of refrigerant oil etc.
Tools for R410A
Flare tool
Size adjustment gauge
Vacuum pump adaptor
Electronic refrigerant
charging scale
Store the piping to be used during installation
indoors and keep both ends of the piping sealed
until just before brazing. (Leave elbow joints, etc.
in their packaging.)
Keep the tools with care.
If dirt, dust or moisture enter into refrigerant cycle, that can
cause deterioration of refrigerant oil or malfunction of compressor.
If dirt, dust or moisture enter into refrigerant cycle, that can
cause deterioration of refrigerant oil or malfunction of compressor.
Use ester oil, ether oil or alkylbenzene oil (small
amount) as the refrigerant oil applied to flares
and flange connections.
If large amount of mineral oil enter, that can cause deterioration of refrigerant oil etc.
Charge refrigerant from liquid phase of gas
cylinder.
Do not use a charging cylinder.
If a charging cylinder is used, the composition of refrigerant will change and the efficiency will be lowered.
Ventilate the room if refrigerant leaks during
operation. If refrigerant comes into contact with
a flame, poisonous gases will be released.
If the refrigerant is charged from gas phase, composition
change may occur in refrigerant and the efficiency will be
lowered.
[1] Cautions for service
(1) Perform service after collecting the refrigerant left in unit completely.
(2) Do not release refrigerant in the air.
(3) After completing service, charge the cycle with specified amount of refrigerant.
(4) When performing service, install a filter drier simultaneously.
Be sure to use a filter drier for new refrigerant.
[2] Additional refrigerant charge
When charging directly from cylinder
· Check that cylinder for R410A on the market is syphon type.
· Charging should be performed with the cylinder of syphon stood vertically. (Refrigerant is charged from liquid phase.)
4
OC335--1.qxp
05.8.5 5:05 PM
Page 5
Unit
Gravimeter
[3] Service tools
Use the below service tools as exclusive tools for R410A refrigerant.
No.
1
Specifications
Gauge manifold
·Only for R410A
·Use the existing fitting specifications. (UNF1/2)
·Use high-tension side pressure of 5.3MPa·G or over.
2
Charge hose
·Only for R410A
·Use pressure performance of 5.09MPa·G or over.
3
Electronic scale
4
Gas leak detector
·Use the detector for R134a, R407C or R410A.
5
Adaptor for reverse flow check
·Attach on vacuum pump.
6
Refrigerant charge base
7
Refrigerant cylinder
·Only for R410A
Top of cylinder (Pink)
Cylinder with syphon
8
Refrigerant recovery equipment
5
OC335--1.qxp
3
05.8.5 5:05 PM
Page 6
PART NAMES AND FUNCTIONS
● Indoor Unit
Filter
Removes dust and pollutants
from intake air
Horizontal Air Outlet
Sets airflow of horizontal automatically
during cooling or dehumidifying.
Grille
Auto Air Swing Vane
Disperses airflow up and
down and adjusts the angle
of airflow direction.
Air Intake
Intakes air from room.
● Wired remote controller
On the controls are set, the same operation mode can be repeated by simply pressing the ON/OFF button.
● Operation buttons
ON/OFF button
Set Temperature buttons
Down
Fan Speed button
Up
Timer Menu button
(Monitor/Set button)
Filter
button
(<Enter> button)
Mode button (Return button)
TEMP.
ON/OFF
Set Time buttons
Check button (Clear button)
Back
Ahead
Test Run button
MENU
BACK
MONITOR/SET
ON/OFF
FILTER
DAY
CHECK TEST
Airflow Up/Down button
Timer On/Off button
(Set Day button)
PAR-21MAA
OPERATION
CLOCK
CLEAR
Louver button
Operation button)
(
To preceding operation
number.
Opening the
door.
Ventilation button
Operation button)
(
To next operation number.
6
OC335--1.qxp
05.8.5 5:05 PM
Page 7
● Display
“Sensor” indication
Displayed when the remote controller
sensor is used.
Day-of-Week
For purposes of this explanation,
all parts of the display are shown
as lit. During actual operation, only
the relevant items will be lit.
Shows the current day of the week.
Time/Timer Display
“Locked” indicator
Shows the current time, unless the simple or Auto Off
timer is set.
If the simple or Auto Off timer is set, shows the time
remaining.
Indicates that remote controller buttons have been locked.
Identifies the current operation
“Clean The Filter” indicator
Shows the operating mode, etc.
* Multilanguage display is supported.
Comes on when it is time to clean the
filter.
TIME SUN MON TUE WED THU FRI SAT
TIMER
Hr
ON
AFTER
FUNCTION
FILTER
˚F˚C
“Centrally Controlled” indicator
Indicates that operation of the remote controller has been prohibited by a master controller.
Timer indicators
AFTER OFF
ERROR CODE
˚F˚C
The indicator comes on if the corresponding timer is set.
WEEKLY
SIMPLE
AUTO OFF
ONLY1Hr.
Fan Speed indicator
Shows the selected fan speed.
“Timer Is Off” indicator
Indicates that the timer is off.
Temperature Setting
Shows the target temperature.
Up/Down Air Direction indicator
Room Temperature display
Shows the room temperature.
The indicator
shows the direction of the outcoming airflow.
Louver display
“One Hour Only” indicator
Indicates the action of the swing
louver. Does not appear if the
louver is stationary.
Displayed if the airflow is set to
weak and downward during COOL
or DRY mode. (Operation varies
according to model.)
The indicator goes off after one
hour, at which time the airflow direction also changes.
Ventilation indicator
Appears when the unit is running in
Ventilation mode.
(Power On indicator)
Indicates that the power is on.
Caution
● Only the Power on indicator lights when the unit is stopped and power supplied to the unit.
● If you press a button for a feature that is not installed at the indoor unit, the remote controller will display the “Not Available”
message.
If you are using the remote controller to drive multiple indoor units, this message will appear only if he feature is not
present at the parent unit.
● When power is turned ON for the first time, it is normal that “PLEASE WAIT” is displayed on the room temperature indication (For max. 2minutes). Please wait until this “PLEASE WAIT” indication disappear then start the operation.
7
OC335--1.qxp
05.8.5 5:05 PM
Page 8
● Wireless remote controller
CHECK TEST RUN display
CHECK&TEST RUN display indicates that
the unit is being checked or test-run.
MODEL SELECT display
Blinks when model is selected.
display
Lights up while transmission to the indoor
unit is mode using switches.
display
SET TEMP. display indicates desired temperature set.
CLOCK display
display
Displays the current time.
OPERATION MODE display
Operation mode display indicates which operation mode is in effect.
TIMER display
CHECK TEST RUN
MODEL SELECT
˚C
AMPM
Displays when in timer operation or when
setting timer.
“
AMPM
NOT AVAILABLE
display
The vertical direction of air flow is indicated.
ON/OFF
“
TEMP
”“
” display
Displays the order of timer operation.
”“
” display
Displays whether timer is on or off.
display
button
FAN SPEED display indicates which fan
speed has been selected.
FAN
AUTO STOP
VANE
AUTO START
SET TEMPERATURE button sets any desired
room temperature.
ON/OFF button
The unit is turned ON and OFF alternately
each time the button is pressed.
MODE
CHECK LOUVER
h
FAN SPEED SELECT button
Used to change the fan speed.
MODE SELECT button
TEST RUN
SET
min
RESET
TIMER CONTROL buttons
AUTO STOP (OFF timer): when this switch
is set, the air conditioner will be automatically stopped at the preset time.
AUTO START (ON timer): when this switch
is set, the air conditioner will be automatically started at the preset time.
CLOCK
Used to switch the operation mode between
cooling, drying, blowing, heating and auto
mode.
h and min buttons
Buttons used to set the “hour and minute” of
the current time and timer settings.
w In case the outdoor unit is cool only type,
the heating mode is not available.
LOUVER button
CHECK-TEST RUN button
This switch the horizontal fan motion ON
and OFF.
Only press this button to perform an inspection check or test operation.
Do not use it for normal operation.
(Not available for this model.)
CLOCK button
VANE CONTROL button
RESET button
Used to change the air flow direction.
SET button
8
OC335--1.qxp
05.8.5 5:05 PM
INDOOR UNIT
Service Ref.
Mode
Power supply(phase, cycle, voltage)
Input
kW
Running current
A
Starting current
A
External finish (Panel)
Heat exchanger
Fan
Fan(drive) o No.
Fan motor output
kW
Airflow(Low-Medium2-Medium1-High) K/min(CFM)
External static pressure
Pa(mmAq)
Booster heater
kW
Operation control & Thermostat
Noise level(Low-Medium2-Medium1-High)
dB
Unit drain pipe I.D.
mm(in.)
Dimensions
mm(in.)
W
mm(in.)
D
mm(in.)
H
Weight
kg(lbs)
INDOOR UNIT
SPECIFICATIONS
Service Ref.
Mode
Power supply(phase, cycle, voltage)
Input
kW
Running current
A
Starting current
A
External finish (Panel)
Heat exchanger
Fan
Fan(drive) o No.
Fan motor output
kW
Airflow(Low-Medium2-Medium1-High) K/min(CFM)
External static pressure
Pa(mmAq)
Booster heater
kW
Operation control & Thermostat
Noise level(Low-Medium2-Medium1-High)
dB
Unit drain pipe I.D.
mm(in.)
Dimensions
mm(in.)
W
mm(in.)
D
mm(in.)
H
Weight
kg(lbs)
INDOOR UNIT
4
Page 9
Service Ref.
Mode
Power supply(phase, cycle, voltage)
kW
Input
A
Running current
A
Starting current
External finish (Panel)
Heat exchanger
Fan
Fan(drive) o No.
kW
Fan motor output
Airflow(Low-Medium2-Medium1-High) K/min(CFM)
Pa(mmAq)
External static pressure
kW
Booster heater
Operation control & Thermostat
dB
Noise level(Low-Medium2-Medium1-High)
mm(in.)
Unit drain pipe I.D.
mm(in.)
W
Dimensions
mm(in.)
D
mm(in.)
H
kg(lbs)
Weight
PLA-RP35AA.UK
Heating
Cooling
Single phase, 50Hz, 230V
0.16
0.79
1.0
0.16
0.79
1.0
Munsell 0.70Y 8.59/0.97
Plate fin coil
Turbo fan (direct) o 1
0.070
11-12-13-14(390-425-460-495)
0(direct blow)
–
Remote controller & built-in
27-28-29-31
32 (1-1/4)
UNIT : 840 (33-1/16)
PANEL : 950 (37-3/8)
UNIT : 840 (33-1/16)
PANEL : 950 (37-3/8)
UNIT : 258 (10-3/16)
PANEL : 30 (1-3/16)
UNIT : 24 (53)
PANEL: 5 (11)
PLA-RP50AA.UK
Cooling
Heating
Single phase, 50Hz, 230V
0.16
0.79
1.0
0.16
0.79
1.0
Munsell 0.70Y 8.59/0.97
Plate fin coil
Turbo fan (direct) o 1
0.070
14-15-16-18(495-530-565-635)
0(direct blow)
–
Remote controller & built-in
28-29-31-33
32(1-1/4)
UNIT : 840 (33-1/16)
PANEL : 950 (37-3/8)
UNIT : 840 (33-1/16)
PANEL : 950 (37-3/8)
UNIT : 258 (10-3/16)
PANEL : 30 (1-3/16)
UNIT : 24 (53)
PANEL: 5 (11)
PLA-RP60AA.UK
Cooling
Heating
Single phase, 50Hz, 230V
0.16
0.79
1.0
0.16
0.79
1.0
Munsell 0.70Y 8.59/0.97
Plate fin coil
Turbo fan (direct) o 1
0.070
14-15-16-18(495-530-565-635)
0(direct blow)
–
Remote controller & built-in
28-29-31-33
32(1-1/4)
UNIT : 840 (33-1/16)
PANEL : 950 (37-3/8)
UNIT : 840 (33-1/16)
PANEL : 950 (37-3/8)
UNIT : 258 (10-3/16)
PANEL : 30 (1-3/16)
UNIT : 24 (53)
PANEL: 5 (11)
9
INDOOR UNIT
Page 10
.
Service Ref
Mode
Power supply(phase, cycle, voltage)
Input
kW
Running current
A
Starting current
A
External finish (Panel)
Heat exchanger
Fan
Fan(drive) o No.
Fan motor output
kW
Airflow(Low-Medium2-Medium1-High) K/min(CFM)
External static pressure
Pa(mmAq)
Booster heater
kW
Operation control & Thermostat
Noise level(Low-Medium2-Medium1-High)
dB
Unit drain pipe I.D.
mm(in.)
Dimensions
mm(in.)
W
mm(in.)
D
mm(in.)
H
Weight
kg(lbs)
INDOOR UNIT
05.8.5 5:05 PM
Service Ref.
Mode
Power supply(phase, cycle, voltage)
Input
kW
Running current
A
Starting current
A
External finish (Panel)
Heat exchanger
Fan
Fan(drive) o No.
Fan motor output
kW
Airflow(Low-Medium2-Medium1-High) K/min(CFM)
External static pressure
Pa(mmAq)
Booster heater
kW
Operation control & Thermostat
Noise level(Low-Medium2-Medium1-High)
dB
Unit drain pipe I.D.
mm(in.)
Dimensions
mm(in.)
W
mm(in.)
D
mm(in.)
H
Weight
kg(lbs)
INDOOR UNIT
OC335--1.qxp
Service Ref.
Mode
Power supply(phase, cycle, voltage)
Input
kW
Running current
A
Starting current
A
External finish (Panel)
Heat exchanger
Fan
Fan(drive) o No.
Fan motor output
kW
Airflow(Low-Medium2-Medium1-High) K/min(CFM)
External static pressure
Pa(mmAq)
Booster heater
kW
Operation control & Thermostat
Noise level(Low-Medium2-Medium1-High)
dB
Unit drain pipe I.D.
mm(in.)
Dimensions
mm(in.)
W
mm(in.)
D
mm(in.)
H
Weight
kg(lbs)
PLA-RP71AA.UK
Cooling
Heating
Single phase, 50Hz, 230V
0.16
0.79
1.0
0.16
0.79
1.0
Munsell 0.70Y 8.59/0.97
Plate fin coil
Turbo fan (direct) o 1
0.070
15-16-18-20(530-565-635-705)
0(direct blow)
–
Remote controller & built-in
28-30-32-34
32(1-1/4)
UNIT : 840 (33-1/16)
PANEL : 950 (37-3/8)
UNIT : 840 (33-1/16)
PANEL : 950 (37-3/8)
UNIT : 258 (10-3/16)
PANEL : 30 (1-3/16)
UNIT : 24 (53)
PANEL: 5 (11)
PLA-RP100AA.UK
Cooling
Heating
Single phase, 50Hz, 230V
0.25
1.25
2.0
0.25
1.25
2.0
Munsell 0.70Y 8.59/0.97
Plate fin coil
Turbo fan (direct) o 1
0.120
20-23-26-28(705-810-920-980)
0(direct blow)
–
Remote controller & built-in
33-36-39-41
32(1-1/4)
UNIT : 840 (33-1/16) PANEL : 950 (37-3/8)
UNIT : 840 (33-1/16) PANEL : 950 (37-3/8)
UNIT : 298 (11-3/4) PANEL : 30 (1-3/16)
UNIT : 30 (66)
PANEL : 5 (11)
PLA-RP125AA.UK
Cooling
Heating
Single phase, 50Hz, 230V
0.33
1.64
2.0
0.33
1.64
2.0
Munsell 0.70Y 8.59/0.97
Plate fin coil
Turbo fan (direct) o 1
0.120
22-25-28-30(775-880-990-1,060)
0(direct blow)
–
Remote controller & built-in
37-40-43-45
32(1-1/4)
UNIT : 840 (33-1/16) PANEL : 950 (37-3/8)
UNIT : 840 (33-1/16) PANEL : 950 (37-3/8)
UNIT : 298 (11-3/4) PANEL : 30 (1-3/16)
UNIT : 32 (71)
PANEL : 5 (11)
10
INDOOR UNIT
Page 11
Service Ref.
Mode
Power supply(phase, cycle, voltage)
Input
kW
Running current
A
Starting current
A
External finish (Panel)
Heat exchanger
Fan
Fan(drive) x No.
Fan motor output
kW
Airflow(Low-Medium2-Medium1-High) K/min(CFM)
External static pressure
Pa(mmAq)
Booster heater
kW
Operation control & Thermostat
Noise level(Low-Medium2-Medium1-High)
dB
Unit drain pipe I.D.
mm(in.)
Dimensions
mm(in.)
W
mm(in.)
D
mm(in.)
H
Weight
kg(lbs)
INDOOR UNIT
05.8.5 5:06 PM
Service Ref.
Mode
Power supply(phase, cycle, voltage)
Input
w1
kW
Running current
w1
A
Starting current
w1
A
External finish
Heat exchanger
Fan
Fan(drive) o No.
Fan motor output
kW
Airflow(Low-Medium2-Medium1-High) K/min(CFM)
External static pressure
Pa(mmAq)
Booster heater
w1
kW
Operation control & Thermostat
Noise level(Low-Medium2-Medium1-High)
dB
Unit drain pipe I.D.
mm(in.)
Dimensions
mm(in.)
W
mm(in.)
D
mm(in.)
H
Weight
kg(lbs)
INDOOR UNIT
OC335--1.qxp
Service Ref.
Mode
Power supply(phase, cycle, voltage)
kW
Input
w1
A
Running current
w1
A
Starting current
w1
External finish
Heat exchanger
Fan
Fan(drive) o No.
kW
Fan motor output
Airflow(Low-Medium2-Medium1-High) K/min(CFM)
Pa(mmAq)
External static pressure
kW
Booster heater
w1
Operation control & Thermostat
dB
Noise level(Low-Medium2-Medium1-High)
mm(in.)
Unit drain pipe I.D.
mm(in.)
W
Dimensions
mm(in.)
D
mm(in.)
H
kg(lbs)
Weight
PLA-RP140AA.UK
Cooling
Heating
Single phase, 50Hz, 230V
0.33
1.64
2.0
0.33
1.64
2.0
Munsell 0.70Y 8.59/0.97
Plate fin coil
Turbo fan (direct) o 1
0.120
22-25-28-30(775-880-990-1,060)
0(direct blow)
–
Remote controller & built-in
37-40-43-45
32(1-1/4)
UNIT : 840 (33-1/16) PANEL : 950 (37-3/8)
UNIT : 840 (33-1/16) PANEL : 950 (37-3/8)
UNIT : 298 (11-3/4) PANEL : 30 (1-3/16)
UNIT : 32 (71)
PANEL : 5 (11)
PLH-P35AAH.UK
Cooling
Heating
Single phase, 50Hz, 230V
0.16
0.79
1.0
0.16<1.29>
0.75<5.61>
1.0<5.61>
Munsell 0.70Y 8.59/0.97
Plate fin coil
Turbo fan (direct) o 1
0.070
11-12-13-14(390-425-460-495)
0(direct blow)
<1.29>
Remote controller & built-in
27-28-29-31
32(1-1/4)
UNIT : 840 (33-1/16)
PANEL : 950 (37-3/8)
UNIT : 840 (33-1/16)
PANEL : 950 (37-3/8)
UNIT : 258 (10-3/16)
PANEL : 30 (1-3/16)
UNIT : 26 (57)
PANEL: 5 (11)
PLH-P50AAH.UK
Cooling
Heating
Single phase, 50Hz, 230V
0.16
0.79
1.0
0.16<1.29>
0.75<5.61>
1.0<5.61>
Munsell 0.70Y 8.59/0.97
Plate fin coil
Turbo fan (direct) o 1
0.070
14-15-16-18(495-530-565-635)
0(direct blow)
<1.29>
Remote controller & built-in
27-28-29-31
32(1-1/4)
UNIT : 840 (33-1/16)
PANEL : 950 (37-3/8)
UNIT : 840 (33-1/16)
PANEL : 950 (37-3/8)
UNIT : 258 (10-3/16)
PANEL : 30 (1-3/16)
UNIT : 26 (57)
PANEL: 5 (11)
w1 : < > Shows the only booster heater rating.
11
INDOOR UNIT
Page 12
Service Ref.
Mode
Power supply(phase, cycle, voltage)
Input
w1
kW
Running current
w1
A
Starting current
w1
A
External finish
Heat exchanger
Fan
Fan(drive) o No.
Fan motor output
kW
Airflow(Low-Medium2-Medium1-High) K/min(CFM)
External static pressure
Pa(mmAq)
Booster heater
w1
kW
Operation control & Thermostat
Noise level(Low-Medium2-Medium1-High)
dB
Unit drain pipe I.D.
mm(in.)
Dimensions
mm(in.)
W
mm(in.)
D
mm(in.)
H
Weight
kg(lbs)
INDOOR UNIT
05.8.5 5:06 PM
Service Ref.
Mode
Power supply(phase, cycle, voltage)
Input
w1
kW
Running current
w1
A
Starting current
w1
A
External finish
Heat exchanger
Fan
Fan(drive) o No.
Fan motor output
kW
Airflow(Low-Medium2-Medium1-High) K/min(CFM)
External static pressure
Pa(mmAq)
Booster heater
w1
kW
Operation control & Thermostat
Noise level(Low-Medium2-Medium1-High)
dB
Unit drain pipe I.D.
mm(in.)
Dimensions
mm(in.)
W
mm(in.)
D
mm(in.)
H
Weight
kg(lbs)
INDOOR UNIT
OC335--1.qxp
Service Ref.
Mode
Power supply(phase, cycle, voltage)
kW
Input
w1
A
Running current
w1
A
Starting current
w1
External finish
Heat exchanger
Fan
Fan(drive) o No.
kW
Fan motor output
Airflow(Low-Medium2-Medium1-High) K/min(CFM)
Pa(mmAq)
External static pressure
kW
Booster heater
w1
Operation control & Thermostat
dB
Noise level(Low-Medium2-Medium1-High)
mm(in.)
Unit drain pipe I.D.
mm(in.)
W
Dimensions
mm(in.)
D
mm(in.)
H
kg(lbs)
Weight
PLH-P60AAH.UK
Heating
Cooling
Single phase, 50Hz, 230V
0.16<1.93>
0.79<8.39>
1.0<8.39>
0.16
0.79
1.0
Munsell 0.70Y 8.59/0.97
Plate fin coil
Turbo fan (direct) o 1
0.070
14-15-16-18(495-530-565-635)
0(direct blow)
<1.93>
Remote controller & built-in
28-29-31-33
32(1-1/4)
UNIT : 840 (33-1/16)
PANEL : 950 (37-3/8)
UNIT : 840 (33-1/16)
PANEL : 950 (37-3/8)
UNIT : 258 (10-3/16)
PANEL : 30 (1-3/16)
UNIT : 26 (57)
PANEL: 5 (11)
PLH-P71AAH.UK
Cooling
Heating
Single phase, 50Hz, 230V
0.16
0.79
1.0
0.16<1.93>
0.79<8.39>
1.0<8.39>
Munsell 0.70Y 8.59/0.97
Plate fin coil
Turbo fan (direct) o 1
0.070
15-16-18-20(530-565-635-705)
0(direct blow)
–
Remote controller & built-in
28-30-32-34
32(1-1/4)
UNIT : 840 (33-1/16)
PANEL : 950 (37-3/8)
UNIT : 840 (33-1/16)
PANEL : 950 (37-3/8)
UNIT : 258 (10-3/16)
PANEL : 30 (1-3/16)
UNIT : 26 (57)
PANEL: 5 (11)
PLH-P100AAH.UK
Cooling
Heating
Single phase, 50Hz, 230V
0.25
1.25
2.0
0.25<2.39>
1.25<10.39>
2.0<10.39>
Munsell 0.70Y 8.59/0.97
Plate fin coil
Turbo fan (direct) o 1
0.120
20-23-26-28(705-810-920-980)
0(direct blow)
<2.39>
Remote controller & built-in
33-36-39-41
32(1-1/4)
UNIT : 840 (33-1/16) PANEL : 950 (37-3/8)
UNIT : 840 (33-1/16) PANEL : 950 (37-3/8)
UNIT : 298 (11-3/4) PANEL : 30 (1-3/16)
UNIT : 32 (71)
PANEL : 5 (11)
w1 : < > Shows the only booster heater rating.
12
Page 13
INDOOR UNIT
05.8.5 5:06 PM
Service Ref.
Mode
Power supply(phase, cycle, voltage)
Input
w1
kW
Running current
w1
A
Starting current
w1
A
External finish
Heat exchanger
Fan
Fan(drive) o No.
Fan motor output
kW
Airflow(Low-Medium2-Medium1-High) K/min(CFM)
External static pressure
Pa(mmAq)
Booster heater
w1
kW
Operation control & Thermostat
Noise level(Low-Medium2-Medium1-High)
dB
Unit drain pipe I.D.
mm(in.)
Dimensions
mm(in.)
W
mm(in.)
D
mm(in.)
H
Weight
kg(lbs)
INDOOR UNIT
OC335--1.qxp
Service Ref.
Mode
Power supply(phase, cycle, voltage)
Input
w1
kW
Running current
w1
A
Starting current
w1
A
External finish
Heat exchanger
Fan
Fan(drive) o No.
Fan motor output
kW
Airflow(Low-Medium2-Medium1-High) K/min(CFM)
External static pressure
Pa(mmAq)
Booster heater
w1
kW
Operation control & Thermostat
Noise level(Low-Medium2-Medium1-High)
dB
Unit drain pipe I.D.
mm(in.)
Dimensions
mm(in.)
W
mm(in.)
D
mm(in.)
H
Weight
kg(lbs)
PLH-P125AAH.UK
Heating
Cooling
Single phase, 50Hz, 230V
0.33<2.76>
1.64<12.00>
2.0<12.00>
0.33
1.64
2.0
Munsell 0.70Y 8.59/0.97
Plate fin coil
Turbo fan (direct) o 1
0.120
22-25-28-30(775-880-990-1,060)
0(direct blow)
<2.76>
Remote controller & built-in
37-40-43-45
32(1-1/4)
UNIT : 840 (33-1/16) PANEL : 950 (37-3/8)
UNIT : 840 (33-1/16) PANEL : 950 (37-3/8)
UNIT : 298 (11-3/4) PANEL : 30 (1-3/16)
UNIT : 34 (75)
PANEL : 5 (11)
PLH-P140AAH.UK
Heating
Cooling
Single phase, 50Hz, 230V
0.33
1.64
2.0
0.33<2.76>
1.64<12.00>
2.0<12.00>
Munsell 0.70Y 8.59/0.97
Plate fin coil
Turbo fan (direct) o 1
0.120
22-25-28-30(775-880-990-1,060)
0(direct blow)
<2.76>
Remote controller & built-in
37-40-43-45
32(1-1/4)
UNIT : 840 (33-1/16) PANEL : 950 (37-3/8)
UNIT : 840 (33-1/16) PANEL : 950 (37-3/8)
UNIT : 298 (11-3/4) PANEL : 30 (1-3/16)
UNIT : 34 (75)
PANEL : 5 (11)
13
OC335--1.qxp
5
05.8.5 5:06 PM
Page 14
NOISE CRITERION CURVES
PLA-RP35AA.UK
PLH-P35AAH.UK
NOTCH SPL(dB)
High
31
Medium1
29
Medium2
28
Low
27
LINE
PLA-RP50AA.UK
PLA-RP60AA.UK
PLH-P50AAH.UK
PLH-P60AAH.UK
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
63
125
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
NC-20
10
250
500
1000
2000
4000
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
PLA-RP71AA.UK
PLH-P71AAH.UK
63
125
250
500
1000
2000
4000
8000
BAND CENTER FREQUENCIES, Hz
NOTCH SPL(dB)
High
34
Medium1
32
Medium2
30
Low
28
LINE
PLA-RP100AA.UK
PLH-P100AAH.UK
90
NOTCH SPL(dB)
High
41
Medium1
39
Medium2
36
Low
33
LINE
90
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
125
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
NC-20
10
63
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 µbar)
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 µbar)
NC-20
10
8000
BAND CENTER FREQUENCIES, Hz
20
LINE
90
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 µbar)
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 µbar)
90
NOTCH SPL(dB)
High
33
Medium1
31
Medium2
29
Low
28
250
500
1000
2000
4000
8000
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
NC-20
10
63
BAND CENTER FREQUENCIES, Hz
125
250
500
1000
2000
BAND CENTER FREQUENCIES, Hz
14
4000
8000
OC335--1.qxp
05.8.5 5:06 PM
Page 15
PLA-RP125AA.UK
PLH-P125AAH.UK
NOTCH SPL(dB)
45
High
43
Medium1
40
Medium2
37
Low
PLA-RP140AA.UK
PLH-P140AAH.UK
LINE
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
LINE
90
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 µbar)
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 µbar)
90
NOTCH SPL(dB)
45
High
43
Medium1
40
Medium2
37
Low
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
NC-20
10
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
NC-20
10
63
125
250
500
1000
2000
4000
8000
63
125
250
BAND CENTER FREQUENCIES, Hz
500
1000
2000
BAND CENTER FREQUENCIES, Hz
UNIT
CEILING
1.5m
MICROPHONE
15
4000
8000
OC335--1.qxp
Page 16
OUTLINES AND DIMENSIONS
Unit : mm
PLA-RP50AA.UK
PLA-RP125AA.UK
PLH-P50AAH.UK
PLH-P125AAH.UK
PLA-RP60AA.UK PLA-RP71AA.UK
PLA-RP140AA.UK
PLH-P60AAH.UK PLH-P71AAH.UK
PLH-P140AAH.UK
Ceiling hole
860 - 910
20 - 45
20 - 45
810
Suspension bolt pitch
Fresh air intake
159
16
197
{125
Burring hole pitch
120 _
158
20 - 45
3 - {2.8
Burring hole
120_
159
C
89
Detail drawing of fresh air intake
98
192
{150
159
840
{100
(Cut out hole)
Suspension bolt M10
or W3/8
1
Ceiling surface
Feeding hole
(Drain pump)
286
374
60
860 - 910
Ceiling hole
Terminal block
840
14 - {2.8
Burring hole
Suspension bolt pitch
605
Branch duct hole
350
{175
167
155
159
130
70_
100
90 100 100 90
Branch duct hole
(Cut out hole)
20 - 45
INDOOR UNIT
PLA-RP35AA.UK
PLA-RP100AA.UK
PLH-P35AAH.UK
PLH-P100AAH.UK
Drain pipe
VP-25connection
(O.D.{32)
Power line entry
Control wire entry
Ceiling surface
+5
0
B
135
Suspension bolt lower edge
17 +50
30
190
105
140
50 - 70
170
A
2
High efficiency filter
& Fresh air intake casement (option)
577
Air intake hole
Air intake grille
17
Grille
Drain hole
M
A
M
Emergency operation switch (cooling)
Emergency operation switch (heating)
Auto vane
577
Air intake hole
(WIRELESS PANEL)
411
Air outlet hole
A
950
6
05.8.5 5:06 PM
DEFROST/STAND BY lamp
M
Receiver
77
Operation lamp
M
Vane motor
51
411
Air outlet hole
950
77
51
Use the current nuts meeting the pipe size of the outdoor unit.
Available pipe size
1 LIQUID SIDE
2 GAS SIDE
RP35, 50
RP60
RP71
[6.35
[6.35
—
—
—
—
[9.52
[9.52
[9.52
[9.52
[9.52
[9.52
[12.7
—
—
—
—
—
[15.88
[15.88
[15.88
[15.88
[15.88
—
—
—
—
[19.05
—
[19.05
RP100, 125, 140 P35,50,60,71 P100, 125, 140
Models
A
B
C
258
80
298
84
PLA-RP35,50,60,71AA
PLH-P35,50,60,71AAH 241
PLA-RP100,125,140AA
Factory flare nut attachment to the heat-exchanger.
16
PLH-P100,125,140AAH
281
Branch
duct hole
OC335--1.qxp
05.8.5 5:06 PM
7
Page 17
WIRING DIAGRAM
PLA-RP35AA.UK
PLA-RP100AA.UK
PLH-P35AAH.UK
PLH-P100AAH.UK
PLA-RP50AA.UK
PLA-RP125AA.UK
PLH-P50AAH.UK
PLH-P125AAH.UK
PLA-RP60AA.UK PLA-RP71AA.UK
PLA-RP140AA.UK
PLH-P60AAH.UK PLH-P71AAH.UK
PLH-P140AAH.UK
[LEGEND]
SYMBOL
P.B
I.B
FUSE
ZNR
BCR
CN2L
CN32
CN41
CN51
LED1
LED2
LED3
X1
X4
SW1
SW2
SWE
C
NAME
INDOOR POWER BOARD
INDOOR CONTROLLER BOARD
FUSE(T6.3AL250V)
VARISTOR
FAN CONTROL ELEMENT
CONNECTOR(LOSSNAY)
CONNECTOR(REMOTE SWITCH)
CONNECTOR(HA TERMINAL-A)
CONNECTOR(CENTRALLY CONTROL)
POWER SUPPLY(I.B)
POWER SUPPLY(I.B)
TRANSMISSION(INDOOR-OUTDOOR)
RELAY(DRAIN PUMP)
RELAY(FAN MOTOR)
SWITCH(MODEL SELECTION)wSee table 1
SWITCH(CAPACITY CORD)wSee table 2
CONNECTOR(EMERGENCY OPERATION)
CAPACITOR(FAN MOTOR)
SYMBOL
MF
MV
H2
DP
DS
TB2
TB4
TB5, TB6
TH1
TH2
TH5
R.B
NAME
SYMBOL
FAN MOTOR
W.B
VANE MOTOR
RU
DEW PREVENTION HEATER
BZ
DRAIN-UP MACHINE
LED1
DRAIN SENSOR
LED2
TERMINAL BLOCK (HEATER)wPLH-P.AAH
SW1
models only or option for PLA-RP.AA models.
SW2
TERMINAL BLOCK (INDOOR/
HEATER
OUTDOOR CONNECTING LINE)
FS1
FS2
TERMINAL BLOCK(REMOTE
CONTROLLER TRANSMISSION LINE)
H1
26H
ROOM TEMP.THERMISTOR
(0:/15k",25:/5.4k" DETECT)
88H
PIPE TEMP.THERMISTOR/LIQUID
(0:/15k",25:/5.4k" DETECT)
COND./EVA. TEMP. THERMISTOR
(0:/15k",25:/5.4k" DETECT)
WIRED REMOTE CONTROLLER BOARD
NAME
WIRELESS REMOTE CONTROLLER BOARD
RECEIVING UNIT
BUZZER
LED(RUN INDICATOR)
LED(HOT ADJUST)
SWITCH(HEATING ON/OFF)
SWITCH(COOLING ON/OFF)
THERMAL FUSE(72:, 16A)
THERMAL FUSE(104:, 16A)
HEATER
HEATER THERMAL SWITCH
HEATER CONTACTOR
GRILLE
MV MV MV MV
5
5
5
5
H2
5
MF
3
2
1
DC
13.1V
2
1
1 2 3 6 7 4 8 9 5 10
1 2 3
CNSK P.B
(RED)
CN2S
(WHT)
TB4
YLW S1
ORN S2
ORN
S3
BRN
TO OUTDOOR UNIT
5
1 2 3
DP
BCR
X4 X1
BRN
ORN
BLK
WHT
1 3 VANE
CND POWER INDOOR/OUTDOOR CN6V
(ORN) CN2D COMMUNICATION (GRN)
(WHT)
CN3C
(BLU)
CN51 CN41 CN2L
1 3 POWER 1 2
FUSE
D.U.M 1 3 D.HEATER 1 3
1 3
CNC(RED)
CNP
POWER
(BLU)
CNDK
(RED)
X4
FAN 1 3 5
(WHT)
YLW
ORN
RED
WHT
YLW
YLW
I.B
YLW
YLW
RED
WHT
BLK
C
X1
ZNR
CN32
SWE SW2
LED3 LED2
HEATER D.SENSOR
CN24
CN31
(YLW)
(WHT)
SW1
ON
OFF
DS
Refer to tables 1
and 2.
BLU
BLU
1 2 3
LED1
INTAKE LIQUID PIPE REMOCON
CN20
CN21 CN29
CN22 WIRELESS
(RED) (WHT) (BLK)
(BLU) CN90
1 2 1 2 1 2
1 2 (WHT)
TH1
2
1
W.B
BZ
9
LED1
SW1
SW2
RU
R.B
TB5
TRANSMISSION WIRES
DC12V
TH2
LED2
CNB
1 2
TB6
TB2
RED
BLU
GRN/YLW
W1 (Fig.1)
TH3
[PLH-P.AAH models only]
I.B
FS2
1 3
WHT 26H
88H
GRY
1 3
POWER INDOOR/OUTDOOR
CND COMMUNICATION
(ORN)
CN3C
(BLU)
1 2
YLW
YLW
I.B
YLW TB4S1
ORN
S2
ORN
S3
BRN
H1
YLW
ORN
POWER SUPPLY
~(1PHASE)
230V 50Hz
TB2
88H
FS1
L
RED
RED
RED
1
N
BLU
WHT
2
GRN/YLW
HEATER CN24
(YLW)
6
5 WHT
L
N
POWER SUPPLY
~(1PHASE)
230V 50Hz
TO OUTDOOR UNIT
Please set the voltage using the
remote controller.
For the setting method. please refer to
the indoor unit Installation Manual.
Table 1
NOTES:
1.Symbols used in wiring diagram above are,
: Connector, : Terminal (block).
2.Indoor and outdoor connecting wires are made with polarities, make wiring
matching terminal numbers (S1,S2,S3).
3.Since the outdoor side electric wiring may change be sure to check the outdoor
unit electric wiring for servicing.
4.This dlagram shows the wiring of Indoor and Outdoor connecting wires
(specification of 230V), adopting superimposed system of power and signal.
w1 ; When work to supply power separately to Indoor and Outdoor unit was applied, refer to Fig1.
w2 ; For power supply system of this unit, refer to the caution label located near this diagram.
MODELS
PLA-RP. AA
PLH-P. AAH
1 2 3 4 5
1 2 3 4 5
ON
OFF
ON
OFF
Table 2
MODELS
17
SW1
Manufacture/Service
SW2
Manufacture/Service MODELS
PLA-RP35AA
PLH-P35AAH
1 2 3 4 5
PLA-RP50AA
PLH-P50AAH
1 2 3 4 5
PLA-RP60AA
PLH-P60AAH
1 2 3 4 5
PLA-RP71AA
PLH-P71AAH
1 2 3 4 5
Manufacture/Service
ON
OFF
PLA-RP100AA
PLH-P100AAH
1 2 3 4 5
ON
OFF
PLA-RP125AA
PLH-P125AAH
1 2 3 4 5
ON
OFF
PLA-RP140AA
PLH-P140AAH
1 2 3 4 5
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OC335--1.qxp
8
05.8.5 5:06 PM
Page 18
REFRIGERANT SYSTEM DIAGRAM
PLA-RP35AA.UK
PLA-RP100AA.UK
PLH-P35AAH.UK
PLH-P100AAH.UK
PLA-RP50AA.UK
PLA-RP125AA.UK
PLH-P50AAH.UK
PLH-P125AAH.UK
PLA-RP60AA.UK PLA-RP71AA.UK
PLA-RP140AA.UK
PLH-P60AAH.UK PLH-P71AAH.UK
PLH-P140AAH.UK
Strainer (#50)
Heat exchanger
Refrigerant GAS pipe connection
(Flare)
Thermistor TH5
(Cond./ Eva.temperature)
Refrigerant flow in cooling
Refrigerant flow in heating
Refrigerant LIQUID pipe connection
(Flare)
Thermistor TH1
(Room temperature)
Thermistor TH2
Pipe temperature(Liquid)
Distributor
with strainer (#50)
Strainer (#50)
18
OC335--1.qxp
05.8.5 5:06 PM
9
Page 19
TROUBLESHOOTING
9-1. TROUBLESHOOTING
<Error code display by self-diagnosis and actions to be taken for service (summary)>
Present and past error codes are logged and displayed on the wired remote controller or controller board of outdoor unit.
Actions to be taken for service and the inferior phenomenon reoccurrence at field are summarized in the table below. Check
the contents below before investigating details.
Unit conditions at service
Error code
Actions to be taken for service (summary)
Displayed
Judge what is wrong and take a corrective action
according to “SELF-DIAGNOSIS ACTION TABLE” (9-3).
Not displayed
Identify the cause of the inferior phenomenon and take
a corrective action according to “TROUBLESHOOTING
BY INFERIOR PHENOMENA ” (9-4).
The inferior phenomenon is
reoccurring.
1Consider the temporary defects such as the work of
protection devices in the refrigerant circuit including
compressor, poor connection of wiring, noise and etc.
Re-check the symptom, and check the installation
environment, refrigerant amount, weather when the
inferior phenomenon occurred, and wiring related.
2Reset error code logs and restart the unit after finishing
service.
3There is no abnormality in electrical components,
controller boards, and remote controller.
Logged
The inferior phenomenon is
not reoccurring.
1Recheck the abnormal symptom.
2Identify the cause of the inferior phenomenon and take
a corrective action according to “TROUBLESHOOTING
BY INFERIOR PHENOMENA ” (9-4).
3Continue to operate unit for the time being if the cause
is not ascertained.
4There is no abnormality in electrical components,
controller boards, remote controller etc.
Not logged
19
OC335--1.qxp
05.8.5 5:06 PM
Page 20
9-2. MALFUNCTION-DIAGNOSIS METHOD BY REMOTE CONTROLLER
<In case of trouble during operation>
When a malfunction occurs to air conditioner, both indoor unit and outdoor unit will stop and operation lamp blinks to inform
unusual stop.
<Malfunction-diagnosis method at maintenance service>
[Procedure]
1. Press the CHECK button twice.
• "CHECK" lights, and refrigerant
address "00" flashes.
• Check that the remote controller's
display has stopped before continuing.
2. Press the temperature
buttons.
• Select the refrigerant address of the
indoor unit for the self-diagnosis.
Note: Set refrigerant address using the
outdoor unit’s DIP switch (SW1).
(For more information, see the
outdoor unit installation manual.)
Refrigerant
address
display
CHECK
CHECK
display
Temperature
button
TEMP
ON/OFF
ON/OFF
button
MODE
FAN
AUTO STOP
VANE
AUTO START
CHECK LOUVER
CHECK
button
min
TEST RUN
SET
h
RESET
CLOCK
HOUR
button
3. Point the remote controller at the • If an air conditioner error occurs, the
sensor on the indoor unit and
indoor unit's sensor emits an intermitpress the HOUR button.
tent buzzer sound, the operation light
flashes, and the error code is
output.
(It takes 3 seconds at most for error
code to appear.)
4. Point the remote controller at the • The check mode is cancelled.
sensor on the indoor unit and
press the ON/OFF button.
To be continued to the next page.
20
OC335--1.qxp
05.8.5 5:06 PM
Page 21
• Refer to the following tables for details on the check codes.
[Output pattern A]
Beeper sounds
OPERATION
INDICATOR
lamp flash
pattern
Beep
Beep Beep Beep
Off
Beep
1st
2 nd
3 rd
nth
On
On
On
On
Beep Beep
1st
Off
On
2 nd · · · Repeated
On
0.5 sec. Approx. 2.5 sec. 0.5 sec. 0.5 sec.
Self-check Approx. 2.5 sec. 0.5 sec. 0.5 sec. 0.5 sec.
starts
(Start signal
Number of flashes/beeps in pattern indicates the check Number of flashes/beeps in pattern indicates
received)
code in the following table (i.e., n=5 for “P5”)
the check code in the following table
[Output pattern B]
Beeper sounds
OPERATION
INDICATOR
lamp flash
pattern
Beep
Beep Beep Beep
1st
Off
On
Approx. 3 sec.
Self-check Approx. 2.5 sec.
starts
(Start signal
received)
2nd
3 rd
On
On
On
0.5 sec. 0.5 sec. 0.5 sec.
Beep
Beep
nth
1st
On
Off
0.5 sec. Approx. 2.5 sec.
Number of flashes/beeps in pattern indicates the check
code in the following table (i.e., n=5 for “U2”)
On
Approx. 3 sec.
Beep
2 nd · · · Repeated
On
On
0.5 sec. 0.5 sec.
Number of flashes/beeps in pattern indicates
the check code in the following table
[Output pattern A] Errors detected by indoor unit
Wireless remote controller Wired remote controller
Beeper sounds/OPERATION
INDICATOR lamp flashes 1 Check code
(Number of times)
1
P1
P2
2
P9
3
E6,E7
4
P4
P5
5
PA
6
P6
7
EE
8
P8
9
E4, E5
–
10
–
11
12
Fb
E0, E3
–
–
E1, E2
Symptom
Remark
Intake sensor error
Pipe (TH2) sensor error
Pipe (TH5) sensor error
Indoor/outdoor unit communication error
Drain sensor error
Drain pump error
Forced compressor stop
Freeing/Overheating safeguard operation
Communication error between indoor and outdoor units
Pipe temperature error
Remote controller signal receiving error
–
–
Indoor unit control system error (memory error, etc.)
Remote controller transmission error
Remote controller control board error
[Output pattern B] Errors detected by unit other than indoor unit (outdoor unit, etc.)
Wireless remote controller Wired remote controller
Beeper sounds/OPERATION
INDICATOR lamp flashes 1 Check code
(Number of times)
1
E9
2
3
4
UP
U3,U4
UF
5
U2
6
U1,Ud
7
8
9
10
U5
U8
U6
U7
11
U9,UH
Symptom
Indoor/outdoor unit communication error
(Transmitting error) (Outdoor unit)
Compressor overcurrent interruption
Open/short of outdoor unit thermistors
Compressor overcurrent interruption (When compressor locked)
Abnormal high discharging temperature/49C worked/
insufficient refrigerant
Abnormal high pressure (63H worked)/Overheating
safeguard operation
Abnormal temperature of heat sink
Outdoor unit fan safeguard stop
Compressor overcurrent interruption/Abnormal of power module
Abnormality of super heat due to low discharge temperature
Abnormality such as overvoltage or voltage shortage and
abnormal synchronous signal to main circuit/Current sensor error
–
–
Other errors (Refer to the technical manual for the outdoor unit.)
Remark
For details, check
the LED display
of the outdoor
controller board.
As for outdoor
unit, refer to
outdoor unit's
service manual.
–
12
–
13
Others
14
*1 If the beeper does not sound again after the initial two beeps to confirm the self-check start signal was received and
the OPERATION INDICATOR lamp does not come on, there are no error records.
*2 If the beeper sounds three times continuously “beep, beep, beep (0.4 + 0.4 + 0.4 sec.)” after the initial two beeps to confirm
the self-check start signal was received, the specified refrigerant address is incorrect.
21
OC335--1.qxp
05.8.5 5:06 PM
Page 22
• On wireless remote controller
2The continuous buzzer sounds from receiving section of indoor unit.
3Blink of operation lamp
• On wired remote controller
1Check code displayed in the LCD.
• If the unit cannot be operated properly after the above test run has been performed, refer to the following table to remove the cause.
Symptom
Cause
Wired remote controller
LED 1, 2 (PCB in outdoor unit)
For about 2
After LED 1, 2 are lighted, LED 2 is •For about 2 minutes following power-on,opPLEASE WAIT
minutes follow- turned off, then only LED 1 is
eration of the remote controller is not possible
lighted. (Correct operation)
ing power-on
due to system start-up. (Correct operation)
•Connector for the outdoor unit’s protection
Only LED 1 is lighted. →
device is not con-nected.
PLEASE WAIT → Error code
LED 1, 2 blink. •Reverse or open phase wiring for the outdoor
After about 2
unit’s power terminal block (L1, L2, L3)
minutes has
expired followDisplay messages do not
•Incorrect wiring between indoor and outdoor
ing power-on Only LED 1 is lighted. →
appear even when operation
LED 1 blinks twice, units (incorrect polarity of S1, S2, S3)
switch is turned ON (operation
LED 2 blinks once. •Remote controller wire short
lamp does not light up).
On the wireless remote controller with condition above, following phenomena takes place.
• No signals from the remote controller are accepted.
• OPE lamp is blinking.
• The buzzer makes a short piping sound.
Note:
Operation is not possible for about 30 seconds after cancellation of function selection. (Correct operation)
For description of each LED (LED1, 2, 3) provided on the indoor controller, refer to the following table.
LED1 (power for microcomputer)
LED2 (power for remote controller)
Indicates whether control power is supplied. Make sure that this LED is
always lit.
Indicates whether power is supplied to the remote controller.
This LED lights only in the case of the indoor unit which is connected to the
outdoor unit refrigerant address “0”.
LED3 (communication between indoor and
outdoor units)
Indicates state of communication between the indoor and outdoor units.
Make sure that this LED is always blinking.
22
OC335--1.qxp
05.8.5 5:06 PM
Page 23
Note: Refer to the manual of outdoor unit for the details of display
such as F, U, and other E.
9-3. SELF-DIAGNOSIS ACTION TABLE
Error Code Meaning of error code and detection method
Abnormality of room temperature
thermistor (TH1)
1 The unit is in three-minute resume
prevention mode if short/open of
thermistor is detected. Abnormal if the
unit does not reset normally after three
minutes. (The unit returns to normal
operation, if it has normally reset.)
2 Constantly detected during cooling,
drying, and heating operation.
Short: 90: or more
P1
Open: -40: or less
Cause
1 Defective thermistor
characteristics.
2 Contact failure of connector
(CN20) on the indoor controller
board. (Insert failure)
3 Breaking of wire or contact
failure of thermistor wiring.
4 Defective indoor controller
board.
Countermeasure
1–3 Check resistance value of thermistor.
0: ······15.0k"
10: ····9.6k"
20: ····6.3k"
30: ····4.3k"
40: ····3.0k"
If you put force on (draw or bend) the lead wire
with measuring resistance value of thermistor
breaking of wire or contact failure can be
detected.
2 Check contact failure of connector (CN20) on
the indoor controller board. Refer to 9-7.
Turn the power on again and check restart
after inserting connector again.
4 Check room temperature display on remote
controller.
Replace indoor controller board if there is
abnormal difference with actual room
temperature.
Turn the power off, and on again to operate
after check.
P2
Abnormality of pipe temperature
thermistor/Liquid (TH2)
1 The unit is in three-minute resume
prevention mode if short/open of
thermistor is detected. Abnormal if the
unit does not reset normally after three
minutes. (The unit returns to normal
operation, if it has normally reset.)
2 Constantly detected during cooling,
drying, and heating (except defrosting)
operation.
Short: 90: or more
Open: -40: or less
1 Defective thermistor
characteristics.
2 Contact failure of connector
(CN21) on the indoor controller
board. (Insert failure)
3 Breaking of wire or contact
failure of thermistor wiring.
4 Defective refrigerant circuit is
causing thermistor temperature
of 90: or more or -40: or
less.
5 Defective indoor controller board.
1–3 Check resistance value of thermistor.
For characteristics, refer to (P1) above.
2 Check contact failure of connector (CN21) on
the indoor controller board. Refer to 9-7. Turn
the power on and check restart after inserting
connector again.
4 Check pipe <liquid> temperature with remote
controller in test run mode. If pipe <liquid>
temperature is exclusively low (in cooling
mode) or high (in heating mode), refrigerant
circuit may have defective.
5 Check pipe <liquid> temperature with remote
controller in test run mode. If there is exclusive
difference with actual pipe <liquid> temperature,
replace indoor controller board.
Turn the power off, and on again to operate
after check.
P4
P5
Abnormality of drain sensor (DS)
1 Suspensive abnormality, if short/open of
thermistor is detected for 30 seconds
continuously.
Turn off compressor and indoor fan.
2 Short/open is detected for 30 seconds
continuously during suspensive
abnormality.
(The unit returns to normal operation,
if it has normally reset.)
3 Detect the following condition.
• During cooling and drying operation.
• In case that pipe <liquid> temperature
- room temperature <-10deg
(Except defrosting)
• When pipe <liquid> temperature or
room temperature is short/open
temperature.
• During drain pomp operation.
1 Defective thermistor
characteristics
2 Contact failure of connector
(CN31) on the indoor controller
board. (Insert failure).
3 Breaking of wire or contact
failure of drain sensor wiring.
4 Defective indoor controller board.
Malfunction of drain pump (DP)
1 Suspensive abnormality, if thermistor
of drain sensor is let heat itself and
temperature rises slightly. Turn off
compressor and indoor fan.
2 Drain pomp is abnormal if the condition
above is detected during suspensive
abnormality.
3 Constantly detected during drain pomp
operation.
1 Malfunction of drain pump
2 Defective drain
Clogged drain pump
Clogged drain pipe
3 Attached drop of water at the
drain sensor
• Drops of drain trickles from
lead wire.
• Clogged filter is causing
wave of drain.
4 Defective indoor controller board.
1–3 Check resistance value of thermistor.
0: ······6.0k"
10: ····3.9k"
20: ····2.6k"
30: ····1.8k"
40: ····1.3k"
2 Check contact failure of connector (CN31) on
the indoor controller board. Refer to 9-7. Turn
the power on again and check restart after
inserting connector again.
4 Replace indoor controller board if drain
pump operates with the line of drain sensor
connector CN31-1 and 2 is short-circuited,
and abnormality reappears.
Turn the power off, and on again to operate
after check.
23
1 Check if drain-up machine works.
2 Check drain function.
3 Check the setting of lead wire of drain sensor
and check clogs of the filter.
4 Replace indoor controller board if drain
pump operates with the line of drain sensor
connector CN31-1 and 2 is short-circuited
and abnormality reappears.
Refer to 9-7.
Turn the power off, and on again to operate
after check.
OC335--1.qxp
05.8.5 5:06 PM
Page 24
Error Code Meaning of error code and detection method
Freezing/overheating protection is
working
1 Freezing protection (Cooling mode)
The unit is in six-minute resume prevention
mode if pipe <liquid or condenser/evaporator> temperature stays under
-15: for three minutes, three minutes
after the compressor started. Abnormal
if it stays under -15: for three minutes
again within 16 minutes after six-minute
resume prevention mode.
<Frost prevention mode>
If pipe <liquid or condenser-evaporator>
temperature is 2: or below when 16
minutes has passed after compressor
starts operating, unit will start operating
in frost prevention mode which stops
compressor operation. After that, when
pipe <liquid or condenser/evaporator>
temperature stays 10: or more for 3
minutes, frost prevention mode will be
released and compressor will restart its
operation.
2 Overheating protection (Heating mode)
P6
The units is in six-minute resume
prevention mode if pipe <condenser /
evaporator> temperature is detected as
over 70: after the compressor started.
Abnormal if the temperature of over
70: is detected again within 10 minutes
after six-minute resume prevention
mode.
(Cooling or drying mode)
1 Clogged filter (reduced airflow)
2 Short cycle of air path
3 Low-load (low temperature)
operation beyond the tolerance
range
4 Defective indoor fan motor
• Fan motor is defective.
• Indoor controller board is
defective.
5 Defective outdoor fan control
6 Overcharge of refrigerant
7 Defective refrigerant circuit
(clogs)
(Heating mode)
1 Clogged filter (reduced airflow)
2 Short cycle of air path
3 Over-load (high temperature)
operation beyond the tolerance
range
4 Defective indoor fan motor
• Fan motor is defective.
• Indoor controller board is
defective.
5 Defective outdoor fan control
6 Overcharge of refrigerant
7 Defective refrigerant circuit
(clogs)
8 Bypass circuit of outdoor unit
is defective.
Abnormality of pipe temperature
<Cooling mode>
Detected as abnormal when the pipe temperature is not in the cooling range 3 minutes later of compressor start and 6 minutes later of the liquid or condenser/evaporator pipe is out of cooling range.
Note 1) It takes at least 9 min. to detect.
Note 2) Abnormality P8 is not detected in
drying mode.
Cooling range : -3 deg ] (TH-TH1)
TH: Lower temperature between: liquid
pipe temperature (TH2) and condenser/evaporator temperature (TH5)
TH1: Intake temperature
P8
<Heating mode>
When 10 seconds have passed after the
compressor starts operation and the hot
adjustment mode has finished, the unit is
detected as abnormal when
condenser/evaporator pipe temperature is
not in heating range within 20 minutes.
Countermeasure
Cause
1 Slight temperature difference
between indoor room
temperature and pipe <liquid
or condenser / evaporator>
temperature thermistor
• Shortage of refrigerant
• Disconnected holder of pipe
<liquid or condenser /
evaporator> thermistor
• Defective refrigerant circuit
2 Converse connection of
extension pipe (on plural units
connection)
3 Converse wiring of indoor/
outdoor unit connecting wire
(on plural units connection)
4 Defective detection of indoor
room temperature and pipe
<condenser / evaporator>
temperature thermistor
5 Stop valve is not opened
completely.
Note 3) It takes at least 27 minutes to
detect abnormality.
Note 4) It excludes the period of defrosting
(Detection restarts when defrosting
mode is over)
Heating range : 3 deg [ (TH5-TH1)
24
(Cooling or drying mode)
1 Check clogs of the filter.
2 Remove shields.
4 Measure the resistance of fan motor's winding.
Measure the output voltage of fan's connector
(FAN) on the indoor controller board.
WThe indoor controller board should be
normal when voltage of AC 220~240V is
detected while fan motor is connected.
Refer to 9-7.
5 Check outdoor fan motor.
67 Check operating condition of refrigerant
circuit.
(Heating mode)
1 Check clogs of the filter.
2 Remove shields.
4 Measure the resistance of fan motor's
winding.
Measure the output voltage of fan's connector
(FAN) on the indoor controller board.
WThe indoor controller board should be
normal when voltage of AC 220~240V is
detected while fan motor is connected.
Refer to 9-7.
5 Check outdoor fan motor.
6~8Check operating condition of refrigerant
circuit.
1~4 Check pipe <liquid or condenser /
evaporator> temperature with room
temperature display on remote
controller and outdoor controller circuit
board.
Pipe <liquid or condenser / evaporator>
temperature display is indicated by
setting SW2 of outdoor controller circuit
board as follows.
Conduct temperature check with outdoor
controller circuit board after connecting
‘A-Control Service Tool(PAC-SK52ST)’.
(
)
23Check converse connection of extension
pipe or converse wiring of indoor/outdoor
unit connecting wire.
OC335--1.qxp
05.8.5 5:06 PM
Page 25
Error Code Meaning of error code and detection method
Abnormality of pipe temperature thermistor / Condenser-Evaporator (TH5)
1 The unit is in three-minute resume protection mode if short/open of thermistor
is detected. Abnormal if the unit does
not get back to normal within three minutes. (The unit returns to normal operation, if it has normally reset.)
2 Constantly detected during cooling, drying, and heating operation (except
defrosting)
Short: 90: or more
Open: -40: or less
P9
Countermeasure
Cause
1 Defective thermistor
1–3 Check resistance value of thermistor.
For characteristics, refer to (P1) above.
characteristics
2 Check contact failure of connector (CN29)
2 Contact failure of connector
on the indoor controller board.
(CN29) on the indoor controller
Refer to 9-7.
board. (Insert failure)
Turn the power on and check restart after
3 Breaking of wire or contact
inserting connector again.
failure of thermistor wiring.
4 Operate in test run mode and check pipe
4 Temperature of thermistor is
<condenser / evaporator> temperature with
90: or more or -40: or less
outdoor controller circuit board. If pipe
caused by defective refrigerant
<condenser / evaporator> temperature is
circuit.
exclusively low (in cooling mode) or high (in
heating mode), refrigerant circuit may have
5 Defective indoor controller
defective.
board.
5 Operate in test run mode and check pipe
<condenser / evaporator> temperature with
outdoor control circuit board. If there is
exclusive difference with actual pipe
<condenser / evaporator> temperature
replace indoor controller board.
There is no abnormality if none of above
comes within the unit.
Turn the power off and on again to operate.
In case of checking pipe temperature
with outdoor controller circuit board,
be sure to connect A-control service
tool (PAC-SK52ST).
(
Remote controller transmission
error(E0)/signal receiving error(E4)
1 Abnormal if main or sub remote controller can not receive normally any
transmission from indoor unit of refrigerant address “0” for three minutes.
(Error code : E0)
2 Abnormal if sub remote controller could
not receive for any signal for two minutes. (Error code: E0)
E0
or
E4
E3
or
E5
1 Contact failure at transmission
wire of remote controller
2 All remote controllers are set
as “sub” remote controller. In
this case, E0 is displayed on
remote controller, and E4 is
displayed at LED (LED1, LED2)
on the outdoor controller circuit
board.
3 Mis-wiring of remote controller.
4 Defective transmitting receiving
1 Abnormal if indoor controller board can
circuit of remote controller
not receive normally any data from
5 Defective transmitting receiving
remote controller board or from other
circuit of indoor controller board
indoor controller board for three minutes.
of refrigerant address “0”.
(Error code: E4)
6 Noise has entered into the
2 Indoor controller board cannot receive
transmission wire of remote
any signal from remote controller for two
controller.
minutes. (Error code: E4)
Remote controller transmission
error(E3)/signal receiving error(E5)
1 Abnormal if remote controller could not
find blank of transmission path for six
seconds and could not transmit.
(Error code: E3)
2 Remote controller receives transmitted
data at the same time, compares the
data, and when detecting it, judges
different data to be abnormal 30
continuous times. (Error code: E3)
)
1 Check disconnection or looseness of indoor
unit or transmission wire of remote controller.
2 Set one of the remote controllers “main”.
If there is no problem with the action above.
3 Check wiring of remote controller.
• Total wiring length: max.500m
(Do not use cablex 3 or more)
• The number of connecting indoor units:
max.16units
• The number of connecting remote controller: max.2units
When it is not the above-mentioned problem of
1~3
4 Diagnose remote controllers.
a) When “RC OK” is displayed,
Remote controllers have no problem.
Put the power off, and on again to check.
If abnormality generates again, replace
indoor controller board.
b) When “RC NG” is displayed,
Replace remote controller.
c) When “RC E3” is displayed,
d) When “ERC 00-06” is displayed,
[ c),d)→Noise may be causing abnormality. ]
∗ If the unit is not normal after replacing
indoor controller board in group control,
indoor controller board of address “0”
may be abnormal.
1 Set a remote controller to main, and the
other to sub.
1 Two remote controller are set
as “main.”
(In case of 2 remote controllers)
2 Remote controller is connected 2 Remote controller is connected with only one
with two indoor units or more.
indoor unit.
3 Repetition of refrigerant
3 The address changes to a separate setting.
address.
4 Defective transmitting receiving 4~6 Diagnose remote controller.
a) When “RC OK”is displayed, remote concircuit of remote controller.
1 Abnormal if indoor controller board could
trollers have no problem.
5
Defective
transmitting
receiving
not find blank of transmission path.
Put the power off,and on again to check.
circuit of indoor controller
(Error code: E5)
When becoming abnormal again, replace
board.
2 Indoor controller board receives transindoor controller board.
mitted data at the same time, compares 6 Noise has entered into transb)When “RC NG”is displayed, replace
the data,and when detecting it, judges
mission wire of remote conremote controller.
different data to be abnormal 30
troller.
c)When “RC E3”or “ERC 00-66”is displayed,
continuous times. (Error code: E5)
noise may be causing abnormality.
25
OC335--1.qxp
05.8.5 5:06 PM
Page 26
Error Code Meaning of error code and detection method
Indoor/outdoor unit communication
error (Signal receiving error)
1 Abnormal if indoor controller board
cannot receive any signal normally for
six minutes after putting the power on.
2 Abnormal if indoor controller board
cannot receive any signal normally for
three minutes.
E6
3 Consider the unit abnormal under the
following condition: When two or more
indoor units are connected to one
outdoor unit, indoor controller board
cannot receive a signal for three minutes
from outdoor controller circuit board, a
signal which allows outdoor controller
circuit board to transmit signals.
Cause
Countermeasure
1 Contact failure, short circuit or, ∗ Check LED display on the outdoor control circuit board. (Connect A-control service tool,
mis-wiring (converse wiring) of
PAC-SK52ST.)
indoor/outdoor unit connecting
Refer to EA-EC item if LED displays EA-EC.
wire
1 Check disconnection or looseness of indoor/
2 Defective transmitting receiving
outdoor unit connecting wire of indoor unit or
circuit of indoor controller board
outdoor unit.
3 Defective transmitting receiving
Check all the units in case of twin triple
circuit of indoor controller board
indoor unit system.
4 Noise has entered into indoor/ 2-4 Turn the power off, and on again to
check. If abnormality generates again,
outdoor unit connecting wire.
replace indoor controller board or outdoor
controller circuit board.
∗ Other indoor controller board may have
defective in case of twin triple indoor unit
system.
E7
Indoor/outdoor unit communication
1 Defective transmitting receiving 1-3 Turn the power off, and on again to
error (Transmitting error)
check. If abnormality generates again,
circuit of indoor controller board
Abnormal if “1” receiving is detected 30
replace indoor controller board.
2 Noise has entered into power
times continuously though indoor controller
supply.
board has transmitted “0”.
3 Noise has entered into outdoor
control wire.
Fb
Abnormality of indoor controller board
Abnormal if data cannot be normally read
from the nonvolatile memory of the indoor
controller board.
E1
or
E2
1 Defective indoor controller
board.
Abnormality of remote controller con1 Defective remote controller.
trol board
1 Abnormal if data cannot be normally
read from the nonvolatile memory of the
remote controller control board.
(Error code: E1)
1 Replace indoor controller board.
1 Replace remote controller.
2 Abnormal if the clock function of remote
controller cannot be normally operated.
(Error code: E2)
PA
(2502)
(2500)
Forced compressor stop
(due to water leakage abnormality)
1 When the intake temperature subtracted
with liquid pipe temperature is less than
-10:, drain sensor is detected whether
it is soaked in the water or not at the interval
of 90 seconds. (Drain pump will start operating
when the drain sensor is detected to be
soaked in the water.)
2 The unit has a water leakage abnormality
when the following conditions, a and b, are
satisfied while the above-mentioned detection
is performed.
a) The drain sensor is detected to be
soaked in the water 10 times in a row.
b) The intake temperature subtracted with
liquid pipe temperature is detected to be
less than -10: for a total of 30 minutes.
(When the drain sensor is detected to
be NOT soaked in the water, the detection
record of a and b will be cleared.)
3 The drain sensor detection is performed
in operations other than cooling. (When
the unit stops operating, during heating
or fan operation, when the unit stops
because of some abnormality)
*Once the water leakage abnormality is
detected, abnormality state will not be
released until the main power is reset.
1) Drain pump trouble
2) Drain defective
· Drain pump clogging
· Drain pipe clogging
3) Open circuit of drain sensor
side heater
Check the drain pump.
Performance
Please confirm whether water can be drained.
Confirm the resistance of the drain sensor side
heater.
4) Contact failure of drain sensor Check the connector contact failure.
connector
5) Dew condensation on drain
sensor
· Drain water descends along
lead wire.
· Drain water waving due to filter
clogging.
1 Check the drain sensor leadwire mounted.
2 Check the filter clogging
6) Extension piping connection
difference at twin, triple,
quadruple system.
Check the piping connection.
7) Mis-wiring of indoor/ outdoor
connecting at twin, triple,
quadruple system.
Check the indoor/ outdoor connecting wires.
8) Room temperature thermistor /
liquid pipe temperature thermistor detection is defective.
Check the room temperature display of remote
controller.
Check the indoor liquid pipe temperature display of outdoor controller board.
26
OC335--1.qxp
05.8.5 5:06 PM
Page 27
9-4. TROUBLESHOOTING BY INFERIOR PHENOMENA
Note: Refer to the manual of outdoor unit for the detail of remote
controller.
Phenomena
(1)LED2 on indoor controller board
is off.
Cause
• When LED1 on indoor controller board is also off.
1 Power supply of rated voltage is not supplied to outdoor unit.
2 Defective outdoor controller circuit board.
3 Power supply of 220~240V is not supplied to indoor
unit.
4 Defective indoor power board.
5 Defective indoor controller board.
(For the separate indoor/outdoor unit power supply system)
1 Power supply of 220~240V AC is not supplied to
indoor unit.
2 The connectors of the optional replacement kit are
not used.
3 Defective indoor controller board.
4 Defective indoor power board.
• When LED1 on indoor controller board is lit.
1 Mis-setting of refrigerant address for outdoor unit
(There is no unit corresponding to refrigerant
address “0”.)
27
Countermeasure
1 Check the voltage of outdoor power
supply terminal block (L, N) or (L3, N).
• When AC 220~240V is not detected.
Check the power wiring to outdoor unit
and the breaker.
• When AC 220~240V is detected.
—Check 2 (below).
2 Check the voltage between outdoor
terminal block S1 and S2.
• When AC 220~240V is not detected.
Check the fuse on outdoor controller
circuit board.
Check the wiring connection.
• When AC 220~240V is detected.
—Check 3 (below).
3 Check the voltage between indoor terminal
block S1 and S2.
• When AC 220~240V is not detected.
Check indoor/outdoor unit connecting
wire for mis-wiring.
• When AC 220~240V is detected.
—Check 4 (below).
4 Check voltage output from CN2S on indoor
power board (DC13.1V). Refer to 9-7-1.
• When no voltage is output.
Check the wiring connection.
• When output voltage is between
DC12.5V and DC13.7V.
—Check 5 (below).
5 Check the wiring connection between
indoor controller board and indoor power
board. Check the fuse on indoor controller
board. If no problems are found, indoor
controller board is defective.
1 Check the voltage of indoor power supply
terminal block (L,N).
• When AC220~240V is not detected.
Check the power supply wiring.
• When AC220~240V is detected.
-Check 2 (below).
2 Check that there is no problem in the
method of connecting the connectors.
• When there are problems in the method
of connecting the connectors.
Connect the connector correctly referring to installation manual of an optional
kit.
• When there is no problem in the
method of connecting the connectors.
-Check 3 (below).
3 Check voltage output from CNDK on
indoor controller board.
• When AC220~240V is not detected.
Check the fuse on indoor controller
board.
Check the wiring connection between
indoor power supply terminal block and
CND on indoor controller board.
• When AC220~240V is detected.
-Check 4 (below).
4 Check voltage output from CN2S on
indoor power board.
• When no voltage output.
Check the wiring connection between
CNDK on indoor controller board and
CNSK on indoor power board.
If no problem are found,indoor power
board is defective.
• When DC12.5~13.7V is detected.
Check the wiring connection between
CN2S on indoor power board and
CN2D on indoor power board.
If no problem are found,indoor controller board is defective.
1 Reconfirm the setting of refrigerant
address for outdoor unit
Set the refrigerant address to “0”.
(For grouping control system under
which 2 or more outdoor units are
connected, set one of the units to “0”.)
Set refrigerant address using SW1 (3-6)
on outdoor controller circuit board.
OC335--1.qxp
05.8.5 5:06 PM
Page 28
Note: Refer to the manual of outdoor unit for the detail of remote
controller.
Phenomena
Cause
Countermeasure
(2)LED2 on indoor controller board
is blinking.
• When LED1 on indoor controller board is also blinking. Check indoor/outdoor unit connecting wire
Connection failure of indoor/outdoor unit connecting for connection failure.
wire
• When LED1 is lit.
1 Check the connection of remote con1 Mis-wiring of remote controller wires
troller wires in case of twin triple indoor
Under twin triple indoor unit system, 2 or more indoor
unit system. When 2 or more indoor units
units are wired together.
are wired in one refrigerant system,
connect remote controller wires to one of
those units.
2 Refrigerant address for outdoor unit is wrong or not 2 Check the setting of refrigerant address
set.
in case of grouping control system.
Under grouping control system, there are some units
If there are some units whose refrigerant
whose refrigerant address is 0.
addresses are 0 in one group, set one of
the units to 0 using SW1 (3-6) on outdoor
controller circuit board.
3 Short-cut of remote controller wires
34 Remove remote controller wires and
4 Defective remote controller
check LED2 on indoor controller board.
• When LED2 is blinking, check the
short-cut of remote controller wires.
• When LED2 is lit, connect remote
controller wires again and:
if LED2 is blinking, remote controller
is defective; if LED2 is lit, connection
failure of remote controller terminal
block etc. has returned to normal.
(3)Upward/downward vane
performance failure
1 The vane is not downward during defrosting and
heat preparation and when the thermostat is OFF in
HEAT mode. (Working of COOL protection function)
2 Vane motor does not rotate.
• Defective vane motor
• Breaking of wire or connection failure of connector
• Up/down vane setting is “No vanes”.
3 Upward/downward vane does not work.
• The vane is set to fixed position.
(4)Receiver for wireless remote
controller
1 Weak batteries of wireless remote controller.
2 Contact failure of connector (CNB) on wireless
remote controller board.
(Insert failure)
3 Contact failure of connector (CN90) on indoor controller board.(Insert failure)
4 Contact failure of connector between wireless
remote controller board and indoor controller board.
28
1 Normal operation (The vane is set to horizontal regardless of remote control.)
2 Check 2 (left).
• Check the vane motor. (Refer to “How
to check the parts”.)
• Check for breaking of wire or connection failure of connector.
• Check “Up/down vane setting”. (Unit
function selection by remote controller).
3 Normal operation (Each connector on
vane motor side is disconnected.)
1 Replace batteries of wireless remote controller.
2~4
Check contact failure of each connector.
If no problems are found of connector,
replace indoor controller board.
When the same trouble occurs even if
indoor controller board is replaced,
replace wireless remote controller
board.
OC335--1.qxp
05.8.5 5:06 PM
Page 29
9-5. EMERGENCY OPERATION
9-5-1. When wireless remote controller troubles or its battery is exhausted
1. Emergency operation is available in such a case using emergency operation switch equipped next to the receiver of indoor
unit.
2. To start operation
• Cooling Operation·······Press
(Cooling) switch.
• Heating Operation·······Press
(Heating) switch.
wWhen the unit starts operating, the operation lamp is lit.
Emergency operation switch (cooling)
Emergency operation switch (heating)
Receiver
Operation lamp
wEmergency operation will be performed as follows.
Cooling
Mode
Set temperature
24:
Fan speed
High
Horizontal
(30deg)
Airflow direction
Heating
24:
High
Downward (70deg)
3. To stop operation
• Press either emergency operation switch (cooling/heating).
9-5-2. When wired remote controller or indoor unit micro computer troubles
1. If there is not any other wrong when trouble occurs, emergency operation starts as the indoor controller board switch (SWE)
is set to ON.
During the emergency operation the indoor unit is as follows;
(1) Indoor fan high speed operation
(2) Drain pump operation
2. When emergency operating for COOL or HEAT, setting of the switch (SWE) in the indoor controller board and outdoor unit
emergency operation are necessary.
3. Check items and notices as the emergency operation
(1) Emergency operation cannot be used as follows;
• When the outdoor unit is something wrong.
• When the indoor fan is something wrong.
• When drain over flow protected operation is detected during self-diagnosis. (Error code : P5)
(2) Emergency operation will be serial operation by the power supply ON/OFF.
ON/OFF or temperature, etc. adjustment is not operated by the remote controller.
(3) Do not operate for a long time as cold air is blown when the outdoor unit starts defrosting operation during heat emergency operation.
(4) Cool emergency operation must be within 10 hours. Other wise, heat exchanger of indoor unit may get frosted.
(5) After completing the emergency operation, return the switch setting, etc. in former state.
(6) Since vane does not work at emergency operation, position the vane slowly by hand.
29
OC335--1.qxp
05.8.5 5:06 PM
Page 30
9-6. HOW TO CHECK THE PARTS
PLA-RP35AA.UK PLA-RP50AA.UK
PLA-RP100AA.UK PLA-RP125AA.UK
PLH-P35AAH.UK PLH-P50AAH.UK
PLH-P100AAH.UK PLH-P125AAH.UK
PLA-RP60AA.UK PLA-RP71AA.UK
PLA-RP140AA.UK
PLH-P60AAH.UK PLH-P71AAH.UK
PLH-P140AAH.UK
Parts name
Check points
Room temperature
thermistor
(TH1)
Pipe temperature
thermistor/liquid(TH2)
Condenser/Evaporator
temperature thermistor
(TH5)
Vane motor
Normal
Abnormal
4.3k"~9.6k"
Open or short
(Refer to the thermistor)
Measure the resistance between the terminals using a tester.
(Surrounding temperature20:)
Fan motor
Normal
Abnormal
15k"
Open or short
Measure the resistance between the terminals using a tester.
(Winding temperature 20:)
Relay connector
1
Disconnect the connector then measure the resistance using a tester.
(Surrounding temperature 10:~30:)
Red
2 White
3 Black
1
2
3
Normal
Motor terminal
or
PLA-RP35,50,60,71AA.UK PLA-RP100,125,140AA.UK
Relay connector PLH-P35,50,60,71AAH.UK PLH-P100,125,140AAH.UK
Red-Black
87.2"
28.7"
White-Black
104.1"
41.6"
Abnormal
Open or short
Protector
OFF:130:
ON :80i20:
Drain pump
Measure the resistance between the terminals using a tester.
(Winding temperature 20:)
YLW
1
Normal
Abnormal
3
290"
Open or short
YLW
Drain sensor
1
2
3
Measure the resistance between the terminals using a tester.
Measure the resistance after 3 minutes have passed since the power supply was intercepted.
(Surrounding temperature 0:~60:)
Normal
Abnormal
0.6k"~6.0k"
Open or short
30
(Refer to the thermistor)
05.8.5 5:03 PM
Page 31
<Thermistor Characteristic graph>
Thermistor for
lower temperature
Room temperature thermistor(TH1)
Pipe temperature thermistor/liquid(TH2)
Condenser/evaporator temperature
thermistor(TH5)
< Thermistor for lower temperature >
50
Resistance (K")
40
Thermistor R0=15k' ± 3%
Fixed number of B=3480 ± 2%
Rt=15exp { 3480(
0:
10:
20:
25:
30:
40:
1
273+t
1
)}
273
15k'
9.6k'
6.3k'
5.4k'
4.3k'
3.0k'
30
20
10
0
Thermistor for
drain sensor
10
-20 -10 0 10 20 30 40 50
Temperature (:)
< Thermistor for drain sensor >
9
8
Thermistor R0=6.0k' ±5%
Fixed number of B=3390 ±2%
1
Rt= 6 exp { 3390(
273+t
0:
10:
20:
25:
30:
40:
Resistance (K")
OC335--2.qxp
1
)}
273
6.0k'
3.9k'
2.6k'
2.2k'
1.8k'
1.3k'
7
6
5
4
3
2
1
0
-20
31
0
20 40 60
Temperature (:)
80
OC335--2.qxp
05.8.5 5:03 PM
Page 32
9-7.TEST POINT DIAGRAM
9-7-1. Power board
PLA-RP35AA.UK PLA-RP50AA.UK
PLA-RP100AA.UK PLA-RP125AA.UK
PLH-P35AAH.UK PLH-P50AAH.UK
PLH-P100AAH.UK PLH-P125AAH.UK
PLA-RP60AA.UK PLA-RP71AA.UK
PLA-RP140AA.UK
PLH-P60AAH.UK PLH-P71AAH.UK
PLH-P140AAH.UK
CN2S
Connect to the indoor controller board (CN2D)
1 (+))
Between 1 to 3 12.6-13.7V DC (Pin1
CNSK
Connect to the indoor controller board
(CNDK)
Between 1 to 3 220-240V AC
32
OC335--2.qxp
05.8.5 5:03 PM
Page 33
9-7-2. Indoor controller board
PLA-RP35AA.UK PLA-RP50AA.UK
PLA-RP100AA.UK PLA-RP125AA.UK
PLH-P35AAH.UK PLH-P50AAH.UK
PLH-P100AAH.UK PLH-P125AAH.UK
CN3C
Transmission
(Indoor/outdoor)
(0~24V DC)
CN2D
Connect to the indoor
power board (CN2S)
(12.5~13.7V DC)
PLA-RP60AA.UK PLA-RP71AA.UK
PLA-RP140AA.UK
PLH-P60AAH.UK PLH-P71AAH.UK
PLH-P140AAH.UK
LED1
Power supply (I.B)
LED2
Power supply (R.B)
LED3
Transmission
(Indoor/outdoor)
CN22
Connect to the terminal
block(TB5)
(Remote controller connecting
wire)
(10.4~14.6V DC)
CN20
Room temperature
thermistor (TH1)
CNDK
Connect to the indoor
power board (CNSK)
(220~240V AC)
CN21
Pipe temperature
thermistor/Liquid (TH2)
CN29
Condenser/evaporator
temperature thermistor (TH5)
FUSE
(6.3 A 250 V)
CN31
Drain sensor (DS)
CN90
Connect to the wireless
remote controller board
(CNB)
CND
Power supply input
(220~240V AC)
CN6V
Vane motor output
(MV)
CNP
Drain-pump output
(DP)
(220~240V AC)
CN41
Connector (HA terminal-A)
CN51
Centrally control
CN24
Heater output
(12V DC)
SWE
Emergency operation
CN2L
Connector
(LOSSNAY)
FAN
Fan motor output
Jumper wire J41, J42
Pair number setting with
wireless remote controller
33
SW2
Capacity setting
SW1
Model setting
OC335--2.qxp
05.8.5 5:03 PM
Page 34
9-8. FUNCTIONS OF DIP SWITCH AND JUMPER WIRE
Each function is controlled by the dip switch and the jumper wire on control p.c. board.
(Marks in the table below)
Jumper wire
Functions
SW1
Model
settings
Setting by the dip switch and jumper wire
MODELS
PLA-RP. AA
PLH-P. AAH
MODELS
SW2
Capacity
settings
J41
J42
Pair number
setting with
wireless
remote
controller
JP1
Unit type
setting
JP3
Indoor
controller
board type
setting
: Short
: Open)
Remarks
Manufacture/Service
1 2 3 4 5
1 2 3 4 5
ON
OFF
ON
OFF
Manufacture/Service
PLA-RP35AA
PLH-P35AAH
1 2 3 4 5
PLA-RP50AA
PLH-P50AAH
1 2 3 4 5
PLA-RP60AA
PLH-P60AAH
1 2 3 4 5
PLA-RP71AA
PLH-P71AAH
1 2 3 4 5
PLA-RP100AA
PLH-P100AAH
1 2 3 4 5
PLA-RP125AA
PLH-P125AAH
1 2 3 4 5
PLA-RP140AA
PLH-P140AAH
1 2 3 4 5
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
<Settings at time of factory shipment>
Wireless remote controller: 0
Control PCB: (for both J41 and J42)
Four pair number settings are supported.
The pair number settings of the wireless remote
controller and indoor control PCB (J41/J42) are
given in the table on the left.
(' ' in the table indicates the jumper line is disconnected.)
Wireless remote Control PCB setting
controller setting
J41
J42
0
1
2
3~9
Model
Without TH5
With TH5
Jumper wire (
JP1
Indoor controller board type
Factory shipment
Service parts
There is no jumper (JP1) because these models
have the cond./eva. temperature thermistor (TH5).
JP3
34
OC335--2.qxp
05.8.5 5:03 PM
10
Page 35
DISASSEMBLY PROCEDURE
PLH-P71AAH.UK
Be careful on removing heavy parts.
OPERATING PROCEDURE
PHOTOS & ILLUSTRATIONS
1. Removing the air intake grille
(1) Slide the knob of air intake grille toward the arrow 1 to
open the air intake grille.
(2) Remove drop prevention hook from the panel.
(3) Slide the shaft in the hinge to the direction of the arrow2
and remove the air intake grille.
Figure 1
Air intake grille
Grille
Air intake grille knob
2. Removing the fan guard
(1) Open the air intake grille.
(2) Remove the 3 screws of fan guard.
Photo 1
Screws
Fan guard
Air intake grille
3. Removing the room temperature thermistor
(1)Remove the fan guard.(See photo 1)
(2) Remove the screw in the room temperature thermistor
holder to remove the holder and the room temperature
thermistor.
(3) Remove the 1 screw from the bell mouth, and unscrew the
other 2 screws (fix to the oval hole which has a different
diameter) to remove the bell mouth.
(4) Hold the holder claw, and remove the room temperature
thermistor and holder.
(5) Disconnect the connector (red) from the indoor control
board.
Photo 2
Screws
Bell mouth
4. Removing the electrical box
Photo 3
(1) Remove the fan guard.(See photo 1)
(2) Disconnect the lead wire of the vane motor from the clamp,
and disconnect the white connector (10P).
Turbo fan
(3) Remove the room temperature thermistor with the holder.
(4) Remove the bell mouth.(See photo 2)
(5) Disconnect the relay connector in the electrical box.
Red (3P) for fan motor
Electrical
White (2P) for pipe temperature detecting thermistor
box
Blue (3P) for drain pump
White (3P) for drain sensor
Green (6P) for auxiliary heater
(6) Remove the 3 screws of the electrical box and loosen the
other 2 screws to remove the box.
Power
<Electrical parts in the electrical box>
supply
Indoor controller board
board
Power supply board
Terminal block
Connector
Capacitor
Heater contactor
35
Room
temperature
thermistor
Air intake grille
Nut
Capacitor
Heater
contactor
Terminal
block
Indoor controller board
Connector
OC335--2.qxp
05.8.5 5:03 PM
Page 36
OPERATING PROCEDURE
PHOTOS & ILLUSTRATIONS
5. Remove the fan motor
(1) Remove the fan guard.(See photo 1)
(2) Remove the bell mouth.(See photo 2)
(3) Remove the electrical box.(See photo 3)
(4) Remove the turbo fan nut.
(5) Pull out the turbo fan.
(6) Disconnect the connector of the fan motor lead wire.
(7) Remove the 4 nuts of the fan motor.
Photo 4
Fan motor
Nut
Nuts
6. Removing the pipe temperature thermistor
and condenser evaporator temperature thermistor
(1) Remove the fan guard.(See photo 1)
(2) Remove the bell mouth.(See photo 2)
(3) Remove the electrical box.(See photo 3)
(4) Remove the turbo fan.
(5) Remove the screw of the service panel.
(6) Remove the service panel.
(7) Remove the pipe temperature thermistor which is inserted
into the holder installed to the thin copper pipe.
(8) Disconnect the 2-pin white connector.(CN21)
[Condenser/ evaporator temperature thermistor]
(9) Remove the drain pan. (See Photo 7)
(10) Remove the thermistor which is installed into the holder
installed to the indoor coil.
(11) Disconnect the 2-pin black connector. (CN29)
Photo 5
Connector
Pipe temperature thermistor
Service access
7. Removing the panel
(1) Remove the air intake grille.(See figure 1)
Corner panel (See figure 2)ß
(1) Remove the corner screw.
(2) Slide the corner panel to the direction of the arrow3, and
remove the corner panel.
Panel (See photo 6)
(1) Disconnect the connector that connects with the unit.
(2) Remove the 2 screws from the panel and loosen another 2
screws, which fix to the oval holes, have different diameters.
(3) Rotate the panel a little to remove the panel.
Figure 2
8. Removing the drain pan
(1) Remove the panel. (See photo 6)
(2) Remove the drain plug (Larger one), drain the remaining
water in the drain pan.
(3) Remove the corner cover. (2 screws)
(4) Remove the bell mouth (See photo 2)
(5) Remove the electrical box. (See photo 3)
(6) Remove the lead wire holder. (1 screw)
(7) Remove the 4 screws and pull out the drain pan.
w Pull out the left and right of the pan gradually.
Be careful not to crack or damage the pan.
Photo 7
Corner
Screw panel
Panel
Corner
panel
Photo 6
Connector
Screws
Panel
Screws
Screw
Screw
Drain pan
Screw
Screw
Lead
wire
holder
36
Drain plug(Larger)
Corner cover
OC335--2.qxp
05.8.5 5:03 PM
Page 37
OPERATING PROCEDURE
PHOTOS & ILLUSTRATIONS
9. Removing the drain pump and drain sensor
(1) Remove the panel. (See photo 6)
(2) Remove the fan guard. (See photo 1)
(3) Remove the bell mouth. (See photo 2)
(4) Remove the electrical box. (See photo 3)
(5) Remove the drain pan. (See photo 7)
(6) Remove the 3 screws of the drain pump.
(7) Cut the drain hose band, pull out the drain hose from the
drain pump.
(8) Pull out the drain pump.
(9) Remove the drain sensor and the holder.
Photo 8
Drain sensor
Screw
Fixing band
Drain hose
Screw
Drain pump
10. Removing the heat exchanger
(1) Remove the panel. (See photo 6)
(2) Remove the fan guard. (See photo 1)
(3) Remove the bell mouth. (See photo 2)
(4) Remove the electrical box. (See photo 3)
(5) Remove the drain pan. (See photo 7)
(6) Remove the turbo fan. (See photo 4)
(7) Remove the 3 screws of the piping cover, and pull out
piping cover.
(8) Remove the 4 screws of the outer wall cover, and pull out
the outer wall cover.
(9) Remove the screw of the coil support.
(10) Remove the 2 screws of the coil.
(11) Pull out the heat exchanger.
Photo 9
Coil support
Coil screws
Heat exchanger
Coil
support
Coil
support
Photo 10
Screw
Outer wall cover
Piping cover
11. Removing the heater
(1) Remove the panel. (See photo 6)
(2) Remove the electrical box. (See photo 3)
(3) Remove the bell mouth.(See photo 2)
(4) Remove the drain pan.(See photo 7)
(5) Remove the turbo fan.(See photo 4)
(6) Remove the 5 screws of the heater assembly.
(7) Remove the clamp(1 screw) securing the lead wire.
(8) Pull the heater assembly out.
Lead wire clamp
Heater
assembly
37
Screws of
piping cover
Heater screw
OC335--2.qxp
05.8.5 5:03 PM
11
Page 38
PARTS LIST
PANEL PARTS
PLA-RP35AA.UK
PLA-RP50AA.UK
PLA-RP60AA.UK
PLA-RP71AA.UK
PLA-RP100AA.UK
PLA-RP125AA.UK
PLA-RP140AA.UK
PLH-P35AAH.UK
PLH-P50AAH.UK
PLH-P60AAH.UK
PLH-P71AAH.UK
PLH-P100AAH.UK
PLH-P125AAH.UK
PLH-P140AAH.UK
GEAR
12
GEAR
(VANE)
11
VANE
BUSH
2
10
9
STEPPING
MOTOR
3
8
1
4
5
13
7
RECEIVER
14
6
CHECK TEST RUN
MODEL SELECT
˚C
AMPM
AMPM
NOT AVAILABLE
ON/OFF
TEMP.
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
ON/OFF
Parts No.
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
E10
E01
E01
E00
E00
E00
24K
E00
E00
E00
E00
E01
KW1
E15
58A
15
TEMP
003
002
638
638
500
691
658
317
223
063
040
040
713
714
246
Q'ty / set
Remarks Wiring RecomSpecifiPLA-RP35,50,60,71,100,125,140AA.UK
Diagram mended
Parts Name
(Drawing
cation PLH-P35,50,60,71,100,125,140AAH.UK
No.) Symbol Q'ty
WIRED
WIRELESS
1
1
AIR OUTLET GRILLE
4
4
VANE ASSY
1
2
CORNER PANEL
3
2
CORNER PANEL
1
1
L.L FILTER-A
1
1
GRILLE ASSY
1
RECEIVER
RU
1
WIRELESS ADAPTER
W.B
4
4
STEPPING MOTOR
MV
8
8
VANE BUSH
4
4
GEAR (VANE)
4
4
GEAR
1
REMOTE CONTROLLER ASSY PAR-21MAA-E
R.B
1
WIRELESS REMOTE CONTROLLER ASSY PAR-SL97A-E
CORD
1
38
Price
Unit
Amount
OC335--2.qxp
05.8.5 5:03 PM
Page 39
FUNCTIONAL PARTS
PLA-RP35AA.UK
PLA-RP50AA.UK
PLA-RP60AA.UK
PLA-RP71AA.UK
16
15
14
13
1
2
2
3
12
4
5
11 MOTOR CAP
SPL WASHER 6
10 CONDENSER
EVAPORATOR
TEMPERATURE
THERMISTOR
7
9 PIPE TEMPERATURE
THERMISTOR
8 FLARE NUT
Q'ty / set
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Parts No.
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
003
E01
005
E00
E00
08K
K16
E17
E40
E15
17J
E20
E50
E00
E02
E06
A41
006
687
130
688
130
114
097
480
480
480
097
202
202
129
659
130
762
105
688
Parts Name
Specification
BASE
LEG
DRUM 1 ASSY
LEG
TURBO FAN
SPL WASHER / NUT
HEAT EXCHANGER
HEAT EXCHANGER
HEAT EXCHANGER
FLARE NUT
5/8"
PIPE TEMPERATURE THERMISTOR
CONDENSER EVAPORATOR TEMPERATURE THERMISTOR
MOTOR CAP
INNER COVER
LEG
FAN MOTOR
D17B6P70MS
MOTOR MOUNT
DRUM 2 ASSY
PLA-RP·AA.UK
35,50
1
2
1
1
1
1
1
39
60
1
2
1
1
1
1
71
1
2
1
1
1
1
Remarks Wiring Recom(Drawing Diagram mended
Symbol Q'ty
No.)
1
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1
4
1
TH2
TH5
MF
Price
Unit
Amount
OC335--2.qxp
05.8.5 5:03 PM
Page 40
FUNCTIONAL PARTS
PLA-RP100AA.UK
PLA-RP125AA.UK
PLA-RP140AA.UK
15
14
16
13
1
2
2
3
12
4
5
11 MOTOR CAP
SPL WASHER 6
10 CONDENSER
EVAPORATOR
TEMPERATURE
THERMISTOR
7
9 PIPE TEMPERATURE
THERMISTOR
8 FLARE NUT
Q'ty / set
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Parts No.
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
003
E01
007
E00
E01
08K
K18
K19
E16
17J
E20
E50
E02
E02
E07
A41
008
687
130
688
130
114
097
480
480
097
202
202
129
659
130
762
105
688
Parts Name
Specification
BASE
LEG
DRUM 1 ASSY
LEG
TURBO FAN
SPL WASHER
HEAT EXCHANGER
HEAT EXCHANGER
FLARE NUT
3/4"
PIPE TEMPERATURE THERMISTOR
CONDENSER EVAPORATOR TEMPERATURE THERMISTOR
MOTOR CAP
INNER COVER
LEG
FAN MOTOR
D176P120MS
MOTOR MOUNT
DRUM 2 ASSY
PLA-RP.AA.UK
100
1
2
1
1
1
1
1
1
1
1
1
1
1
1
4
1
40
125,140
1
2
1
1
1
1
1
1
1
1
1
1
1
1
4
1
Remarks Wiring Recom(Drawing Diagram mended
Symbol Q'ty
No.)
TH2
TH5
MF
Price
Unit
Amount
OC335--2.qxp
05.8.5 5:03 PM
Page 41
FUNCTIONAL PARTS
PLH-P35AAH.UK
PLH-P50AAH.UK
PLH-P60AAH.UK
PLH-P71AAH.UK
20
19
18
17
1
2
2
3
16
4
5
15 MOTOR CAP
14 THERMAL FUSE
SPL WASHER 6
13 THERMAL FUSE
12 HEATER THERMAL
7
SWITCH
11
10 CONDENSER
EVAPORATOR
TEMPERATURE
THERMISTOR
8
9 PIPE TEMPERATURE
THERMISTOR
Q'ty / set
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Parts No.
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
003
E01
005
E00
E00
08K
E08
E07
E20
17J
E20
20J
46K
E02
E03
E50
E01
E02
E06
A41
006
687
130
688
130
114
097
300
300
480
202
202
303
700
706
706
129
659
130
762
105
688
Parts Name
BASE
LEG
DRUM 1 ASSY
LEG
TURBO FAN
SPL WASHER
HEATER ELEMENT
HEATER ELEMENT
HEAT EXCHANGER
PIPE TEMPERATURE THERMISTOR
CONDENSER EVAPORATOR TEMPERATURE THERMISTOR
INSULATOR
HEATER THERMAL SWITCH
THERMAL FUSE
THERMAL FUSE
MOTOR CAP
INNER COVER
LEG
FAN MOTOR
MOTOR MOUNT
DRUM 2 ASSY
Specification
240V/467W
240V/700W
50°C OFF
104°C, 16A
72°C, 16A
D17B6P70MS
41
PLH -P·AAH.UK
35,50
1
2
1
1
1
1
3
1
1
1
1
1
1
1
1
1
1
1
4
1
60
1
2
1
1
1
1
71
1
2
1
1
1
1
3
1
1
1
1
1
1
1
1
1
1
1
4
1
3
1
1
1
1
1
1
1
1
1
1
4
1
Remarks Wiring RecomDiagram mended
(Drawing No.) Symbol Q'ty
H1
H1
TH2
TH5
26H
FS2
FS1
MF
Price
Unit Amount
OC335--2.qxp
05.8.5 5:04 PM
Page 42
FUNCTIONAL PARTS
PLH-P100AAH.UK
PLH-P125AAH.UK
PLH-P140AAH.UK
20
19
18
17
1
2
2
3
16
4
5
15 MOTOR CAP
14 THERMAL FUSE
SPL WASHER 6
13 THERMAL FUSE
12 HEATER THERMAL
7
SWITCH
11
10 CONDENSER
EVAPORATOR
TEMPERATURE
THERMISTOR
8
9 PIPE TEMPERATURE
THERMISTOR
Q'ty / set
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Parts No.
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
S70
003
E01
007
E00
E01
08K
E06
E05
E21
E25
17J
E20
20J
46K
E02
E04
E50
E04
E02
E07
A41
008
687
130
688
130
114
097
300
300
480
480
202
202
303
700
706
706
129
659
130
762
105
688
Parts Name
BASE
LEG
DRUM 1 ASSY
LEG
TURBO FAN
SPL WASHER
HEATER ELEMENT
HEATER ELEMENT
HEAT EXCHANGER
HEAT EXCHANGER
PIPE TEMPERATURE THERMISTOR
CONDENSER EVAPORATOR TEMPERATURE THERMISTOR
INSULATOR
HEATER THERMAL SWITCH
THERMAL FUSE
THERMAL FUSE
MOTOR CAP
INNER COVER
LEG
FAN MOTOR
MOTOR MOUNT
DRUM 2 ASSY
Specification
240V/867W
240V/1000W
PLH -P100
AAH.UK
1
2
1
1
1
1
3
Remarks Wiring RecomPLH -P125,140 (Drawing No.) Diagrammended
Symbol Q'ty
AAH.UK
1
2
1
1
1
1
H1
H1
3
1
50°C OFF
104°C, 16A
72°C, 16A
D176P120MS
1
1
1
1
1
1
1
1
1
1
4
1
42
1
1
1
1
1
1
1
1
1
1
1
4
1
TH2
TH5
26H
FS2
FS1
MF
Price
Unit Amount
OC335--2.qxp
05.8.5 5:04 PM
Page 43
FUNCTIONAL PARTS
PLA-RP35AA.UK PLA-RP100AA.UK
PLA-RP50AA.UK PLA-RP125AA.UK
PLA-RP60AA.UK PLA-RP140AA.UK
PLA-RP71AA.UK
1
2
17 DRAIN PLUG
16 DRAIN PLUG
3
15
4
14 CAPACITOR
5
6
13 TERMINAL BLOCK
7
12 TERMINAL BLOCK
8
11 ROOM
TEMPERATURE
THERMISTOR
9
10
Part numbers that is circled is not shown in the figure.
Q'ty / set
No.
Parts No.
S70
1 S70
S70
2 S70
3 S70
4 S70
5 S70
6 S70
7 S70
8 S70
9 S70
10 S70
11 S70
12 S70
13 S70
S70
14 S70
S70
15 S70
16 S70
17 S70
18 S70
E02
E00
E01
29H
E02
E00
31K
E30
K06
K80
003
E10
E00
512
E01
576
17T
E02
001
A48
A41
A41
529
529
529
523
355
266
241
501
313
310
503
675
202
716
716
255
255
255
663
524
524
523
Parts Name
DRAIN PAN
DRAIN PAN
DRAIN PAN
DRAIN SOCKET
DRAIN PUMP
DRAIN SENSOR
DRAIN SENSOR HOLDER
ELECTRICAL CONTROL BOX
POWER BOARD
INDOOR CONTROLLER BOARD
CONTROL COVER ASSY
FAN GUARD
ROOM TEMPERATURE THERMISTOR
TERMINAL BLOCK
TERMINAL BLOCK
CAPACITOR
CAPACITOR
CAPACITOR
CORNER COVER
DRAIN PLUG
DRAIN PLUG
DRAIN HOSE ASSY
Specification
PLA-RP · AA.UK
35,50,60
1
71
1
100 125,140
Remarks Wiring RecomDiagram mended
(Drawing No.) Symbol Q'ty
1
2P (1, 2)
3P (S1, S2, S3)
3+ 440V
3.5+ 440V
7+ 440V
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
43
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
DP
DS
P.B
I.B
TH1
TB5
TB4
C
C
C
Price
Unit
Amount
OC335--2.qxp
05.8.5 5:04 PM
Page 44
FUNCTIONAL PARTS
PLH-P35AAH.UK PLH-P100AAH.UK
PLH-P50AAH.UK PLH-P125AAH.UK
PLH-P60AAH.UK PLH-P140AAH.UK
PLH-P71AAH.UK
1
19 DRAIN PLUG
2
18 DRAIN PLUG
3
17
4
16 CAPACITOR
5
15 RELAY
6
14 TERMINAL BLOCK
7
13 TERMINAL BLOCK
12 TERMINAL BLOCK
8
11 ROOM
TEMPERATURE
THERMISTOR
9
10
Part number that is circled is not shown in the figure.
Q'ty / set
No.
Parts No.
S70
1 S70
S70
2 S70
3 S70
4 S70
5 S70
6 S70
7 S70
8 S70
9 S70
10 S70
11 S70
12 S70
13 S70
14 S70
15 S70
S70
16 S70
S70
17 S70
18 S70
19 S70
20 S70
E02
E00
E01
29H
E02
E00
31K
E30
K06
K80
003
E10
E00
512
E01
521
71G
576
17T
E02
001
A48
A41
A41
529
529
529
523
355
266
241
501
313
310
503
675
202
716
716
716
215
255
255
255
663
524
524
523
Specification
Parts Name
DRAIN PAN
DRAIN PAN
DRAIN PAN
DRAIN SOCKET
DRAIN PUMP
DRAIN SENSOR
DRAIN SENSOR HOLDER
ELECTRICAL CONTROL BOX
POWER BOARD
INDOOR CONTROLLER BOARD
CONTROL COVER ASSY
FAN GUARD
ROOM TEMPERATURE THERMISTOR
TERMINAL BLOCK
TERMINAL BLOCK
TERMINAL BLOCK
RELAY
CAPACITOR
CAPACITOR
CAPACITOR
CORNER COVER
DRAIN PLUG
DRAIN PLUG
DRAIN HOSE ASSY
PLH -P • AAH.UK
35,50,60
1
71
1
100
125,140
Remarks Wiring RecomDiagram mended
(Drawing No.) Symbol Q'ty
Price
Unit Amount
1
2P (1, 2)
3P (S1, S2, S3)
3P (L, N, ;)
JC-1A DC12V
3+ 440V
3.5+ 440V
7.0+ 440V
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
DP
DS
P.B
I.B
TH1
TB5
TB4
TB2
88H
C
C
C
HEAD OFFICE : MITSUBISHI DENKI BLDG., 2-2-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
CCopyright 2005 MITSUBISHI ELECTRIC ENGINEERING CO., LTD.
Distributed in Aug. 2005 No.OC335 PDF 8
Made in Japan.
New publication, effective Aug. 2005.
Specifications subject to change without notice.