Download Sharp GX-CD1200W GL Service manual
Transcript
GX-CD1200W SERVICE MANUAL No. S5039GXCD1200 PORTABLE CD STEREO COMPONENT SYSTEM GX-CD1200W(BK) MODEL GX-CD1200W(GL) • In the interests of user-safety the set should be restored to its original condition and only parts identical to those specified should be used. CONTENTS Page SPECIFICATIONS ............................................................................................................................................................... 1 VOLTAGE SELECTION ....................................................................................................................................................... 2 AC POWER SUPPLY CORD AND AC PLUG ADAPTOR ................................................................................................... 2 FITTING OF DIAL POINTER ............................................................................................................................................... 2 NAMES OF PARTS ............................................................................................................................................................. 3 DISASSEMBLY .................................................................................................................................................................... 4 REMOVING AND REINSTALLING THE MAIN PARTS ....................................................................................................... 5 ADJUSTMENT ..................................................................................................................................................................... 6 SCHEMATIC DIAGRAM / WIRING SIDE OF P.W.BOARD ............................................................................................... 10 NOTES ON SCHEMATIC DIAGRAM ................................................................................................................................ 18 TYPES OF TRANSISTOR AND LED ................................................................................................................................. 18 VOLTAGE .......................................................................................................................................................................... 18 WAVEFORMS OF CD CIRCUIT ........................................................................................................................................ 19 TROUBLESHOOTING (CD SECTION) ............................................................................................................................. 20 FUNCTION......................................................................................................................................................................... 24 PARTS GUIDE / EXPLODED VIEW SPECIFICATIONS General Power source: Power consumption: Output power: Input terminal: Output terminal: Dimensions: Weight: Radio section AC 110-127 V/220-240 V, 50/60 Hz DC 15 V [“D” size (UM/SUM-1, R20 or HP2) battery x 10] 31 W PMPO; 200 W (Total) (AC operation) MPO; 50 W (25 W + 25 W) (AC operation) RMS; 25 W (12.5 W + 12.5 W) (DC operation, 10 % T.H.D.) Mixing microphone(monaural); 600 ohms Headphones; 16-50 ohms (recommended; 32 ohms) Width; 300 mm (11-13/16") Height; 262 mm (9-1/2") Depth; 220 mm (8-11/16") 4.1 kg (9.1 lbs.) without batteries Frequency range: Tape recorder section Frequency response: Signal/noise ratio: Wow and flutter: Motor: Bias system: Erase system: Audio channels: Filter: D/A converter: Wow and flutter: 60 - 12,000 Hz (Normal tape) 40 dB (TAPE 1, recording/playback) 55 dB (TAPE 2, playback) 0.15 % (WRMS) DC 9 V electric governor AC bias Magnet erase Speaker section Type: Speakers: 2-way type 12 cm (4-3/4") free-edge speaker x 2 Tweeter x 2 Maximum input power: 25 W Rated input power: 12.5 W Impedance: 8 ohms Dimensions: Width; 235 mm (9-1/4") Height; 262 mm (10-5/16") Depth; 220 mm (8-11/16") Weight: 1.8 kg (4.0 lbs.)/each Compact disc player Type: Signal readout: FM; 88 - 108 MHz SW1; 2.3 - 7.3 MHz SW2; 7.3 - 22 MHz MW; 526.5 - 1,606.5 kHz Compact disc Non-contact, 3-beam semi-conductor laser pickup 2 8-times oversampling digital filter 1-bit D/A converter Unmeasurable (less than 0.001 % W. peak) Specifications for this model are subject to change without prior notice. SHARP CORPORATION –1– This document has been published to be used for after sales service only. The contents are subject to change without notice. GX-CD1200W FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER TO THE OPERATION MANUAL. VOLTAGE SELECTION Before operating the unit on mains, check the preset voltage. If the voltage is different from your local voltage, adjust the voltage as follows: Slide the voltage selector with a screwdriver to the appropriate voltage number (AC 110V-127V or AC 220V-240V). AC POWER SUPPLY CORD AND AC PLUG ADAPTOR QACCE0007AW00 QACCA0001SJ00 QPLGA0250AFZZ QACCL0002AW00 QPLGA0253AFZZ FITTING OF DIAL POINTER 1. Remove the Main PWB, the Graphic Equalizer PWB, the Volume PWB and the Fine Tuning PWB. (See Figure 4-2 in the "Disassembly" on page 4.) 2. Remove the dial pointer guide and PWB. 3. Insert the dial pointer from A , lead it under B , hang it on the tuner gear and then pass it through C . 4. Replace the Main PWB, the Graphic Equalizer PWB, the Volume PWB and the Fine Tuning PWB. 5. Rotate the tuning knob in the arrow direction until it stops. (Set the tuner variable capacitor to "0" point (F-LOW state).) 6. Adjust the dial pointer so that its stopper becomes the Figure 2-2 position. (Adjust the engagement of the pointer gear and the tuner gear to get the minimum space between the PWB and the stopper.) This position is the "0" point. 7. Screw up the PWB and the dial pointer guide. "0" Point Dial Pointer(211) A Front Cabinet Tuning Knob B Dial Pointer(211) Graphic Equalizer PWB Fine Tuning PWB Screw(601) ø3x10mm C PWB Tuner Gear Volume PWB Dial Pointer Guide (218) Main PWB Figure 2-1 Make the minimum space. PWB Dial Pointer Stopper Pointer Gear Tuner Gear Main PWB Front Cabinet Variable Capacitor Figure 2-2 –2– GX-CD1200W NAMES OF PARTS 1. CD Compartment 2. CD Eject Button 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. Track Number Indicator (CD) Play Indicator (CD) Pause Indicator Extra Bass Control Graphic Equalizer Controls Power/(TAPE 2) Play Direction Indicators (CD) Track Down/Review Button (CD) Track Up/Cue Button (CD) Stop Button (CD) Play/Pause Button Fine Tuning Control Built-in Microphone Volume Control Headphone Socket Mixing Microphone Socket Function Selector Switch (TAPE 1) Cassette Compartment Tuning Control FM Stereo Indicator Surround Indicator Surround Switch Band Selector Switch Dubbing Speed/Built-in Microphone/FM Mode Switch (TAPE 2) Cassette Compartment 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. (TAPE 1) Record Button (TAPE 1) Play Button (TAPE 1) Rewind Button (TAPE 1) Fast Forward Button (TAPE 1) Stop/Eject Button (TAPE 1) Pause Button (TAPE 2) Reverse Mode Switch (TAPE 2) Play Button (TAPE 2) Fast Wind Buttons (TAPE 2) Stop/Eject Button (TAPE 2) Direction Switch 38. 39. 40. 41. 42. 43. FM/SW Telescopic Rod Aerial Beat Cancel Switch Speaker Terminals AC Voltage Selector AC Power Input Socket Battery Compartment 44. 45. 46. 47. 48. Tweeter Bass Reflex Duct Woofer Speaker Release Lever Speaker Wire (Continued) 1 2 3 4 5 6 7 8 9 10 11 12 13 20 14 15 16 17 18 21 22 23 24 25 19 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 47 45 46 –3– 48 GX-CD1200W DISASSEMBLY Caution on Disassembly Follow the below-mentioned notes when disassembling the unit and reassembling it, to keep it safe and ensure excellent performance: 1. Take cassette tape out of the unit. 2. Be sure to remove the power supply plug from the wall outlet before starting to disassemble the unit and remove the batteries from the unit. 3. Take off nylon bands or wire holders where they need to be removed when disassembling the unit. After servicing the unit, be sure to rearrange the leads where they were before disassembling. 4. Take sufficient care on static electricity of integrated circuits and other circuits when servicing. CD Player Unit Front Cabinet (B1)x2 ø3x10mm CD SERVO PWB (B2)x1 MAIN UNIT STEP 1 REMOVAL Front Cabinet/ Rear Cabinet PROCEDURE FIGURE 1. Battery Compartment Lid. ................................. (A1)x1 2. Screw ................... (A2)x5 3. Screw ................... (A3)x3 4. Socket .................. (A4)x1 4-1 Fine Tuning PWB 2 CD Player Unit 1. Screw ................... (B1)x2 2.Socket ................... (B2)x1 4-2 3 Main PWB/ Graphic Equalizer PWB/ Volume PWB/ Fine Tuning PWB 1. Knob ..................... (C1)x1 2. Socket .................. (C2)x3 3. Screw ................... (C3)x5 4. Screw ................... (C4)x2 5. Mic ....................... (C5)x1 4-3 Tape mechanism 1. Open the cassette holder. 2. Screw ................... (D1)x6 4-3 Power PWB/ 1. Screw ................... (E1)x3 Terminal A PWB/ 2. Screw ................... (E2)x2 Terminal B PWB 3. Bracket ................. (E3)x1 4. Screw ................... (E4)x2 5. Hook ..................... (E5)x2 CD Servo PWB/ 1. Screw ................... (F1)x7 CD Control PWB/ 2. Socket .................. (F2)x3 CD Mechanism 1. Screw ................... (G1)x1 4-4 4 5 6 7 Figure 4-2 Front Cabinet 1 REMOVAL Speaker (C1)x1 Washer Main PWB Open (C4)x2 ø3x10mm (C5)x1 (D1)x4 ø3x10mm 5-1 (C3)x5 ø3x10mm 5-1 (C2)x3 SPEAKER UNIT STEP Volume Graphic PWB Equalizer PWB Nat Cassette Holder (D1)x2 Tape (Left/Right) ø3x10mm Mechanism Figure 4-3 PROCEDURE FIGURE 1. Screw ................... (H1)x5 2. Front Panel .......... (H2)x1 3. Screw ................... (H3)x4 5-2 Power Transeformer Voltage Selector Rear Cabinet Main PWB AC Socket Power PWB (A2)x1 ø3x6mm (A4)x1 Front Cabinet (A3)x3 ø3x20mm (E5)x2 (E1)x3 ø3x10mm (E2)x2 ø4x16mm (A2)x3 ø3x6mm (E3)x1 (A1)x1 Rear Cabinet (E4)x2 ø3x10mm (A2)x1 ø3x6mm Figure 4-1 Terminal B PWB Terminal A PWB Figure 4-4 –4– GX-CD1200W CD Servo PWB (F1)x3 ø3x10mm (G1)x3 ø3x10mm Front Panel Tweeter (H2)x1 Speaker Cord Speaker Holder Cord Woofer (F2)x2 Driver (F2)x1 CD Mechanism (F1)x1 ø3x10mm (H3)x4 ø3x10mm Switch PWB Main Unit CD Player Unit (F1)x3 ø3x10mm Speaker Release Lever Speaker Box CD Control PWB Figure 5-2 Figure 5-1 REMOVING AND REINSTALLING THE MAIN PARTS CD MECHANISM SECTION (A1)x2 Perform steps 1,2,6 and 7 of the disassembly method to remove the CD mechanism. How to remove the pickup (See Fig. 5-3.) (A2)x1 1. Remove the hooks (A1) x 2 pcs., to remove the CD Mechanism Cover (A2) x1 pc. 2. Remove the screws (A3) x 2 pcs., to remove the shaft (A4) x1 pc. 3. Remove the stop washer (A5) x1 pc., to remove the gear (A6) x 1 pc. 4. Remove the pickup. (A3) x2 ø2.6 x6mm CD Mechanism Pickup Note : (Figure 5-1 and Figure 5-3) After removing the connector for the optical pick-up from the connector, wrap the conductive aluminium foil around the front end of connector to protect the optical pick-up from electrostatic damage. Shaft (A4) x1 Gear (A6) x1 Figure 5-3 –5– Stop Washer (A5) x1 (H1)x5 ø4x16mm GX-CD1200W TAPE MECHANISM SECTION Perform steps 1, 2, 3 and 4 of the disassembly method to remove the mechanism block. (A1) x1 ø2x7mm (A1) x1 ø2x3mm Hook (A2) x2 How to remove the record / playback, playback and erase heads (See Figs. 6-1 and 6-2.) 1. Remove the screws (A1) x 2 pcs., to remove the record/ playback head. 2. Remove the hooks (A2) x 2 pcs., toward the center position as shown in Fig. 6-1. and then extract the erase head upward. 3. Remove the screws (B1) x 2 pcs., to remove the playback head. Note: After replacing the heads and performing the azimuth adjustment, be sure to apply screw lock. TAPE 1 Record/Playback Head Erase Head Figure 6-1 (B1) x1 ø2x7mm How to remove the pinch roller (See Fig. 6-3.) (B1) x1 ø2x3mm TAPE 2 Playback Head 1. Carefully bend the pinch roller pawl in the direction of the arrow <A> , and remove the pinch roller (C1) upwards. How to remove the motor (See Fig. 6-4.) 1. Remove the belt. 2. Remove the screws (D1) x 4 pcs., to remove the motor bracket. 3. Remove the screws (D2) x 3 pcs., to remove the motor. Note: When mounting the motor, pay attention to the motor mounting angle. How to remove the belts (See Fig. 6-5.) Figure 6-2 1. Remove the main belt (E1) x 1 pc., at the tape 1 side from the motor pulley. 2. Remove the main belt (E2) x 1 pc., at the tape 2 side from the motor pulley. 3. Remove the REW/FF belt (E3) x 2 pcs., from the REW/FF roller. 4. Put on the belts in the reverse order of removal. Note: When putting on the belt, ascertain that the belt is not twisted, and clean it. Pinch Roller (C1) Pinch Roller Pawl <A> Figure 6-3 Motor TAPE 2 REW / FF Belt (E3) x1 ( D1 ) x2 ø2 x 4mm ( D1 ) x2 ø2 x 4mm Motor TAPE 2 TAPE 1 Main Belt Main Belt Motor Bracket ( D2 ) x3 Special Screw Motor Main Belt (E1) x1 TAPE 1 Main Belt (E2) x1 Motor Bracket REW / FF Belt (E3) x1 Motor Figure 6-5 Figure 6-4 –6– GX-CD1200W ADJUSTMENT MECHANISM SECTION TUNER SECTION • Driving Force Check fL: Low-range frequency fH: High-range frequency Torque Meter Specified Value Play: TW-2412 • FM IF/RF Tape 1: Over 60 g Tape 2: Over 50 g Specified Value/ Adjusting Point Test Stage • Torque Check Torque Meter Specified Value Tape 1 Tape 2 Play: TW-2111 30 to 70 g.cm 27 to 60 g.cm Fast Forward: TW-2231 Over 55 g.cm 55 to 120 g.cm Rewind: TW-2231 Over 55 g.cm 55 to 120 g.cm Test Tape Instrument Connection MTT-114 Headphones Socket (Load resistance: 32 ohms) Adjustment Point Specified Value Instrument Connection DECK SECTION • Bias Oscillation • Beat Cancel Switch: C L301 Specified value 100 kHz + 4 kHz Instrument Connection 2.5 V ± 3 dB Instrument Connection AM IF L11 Input: Antenna Output: Pin 9 of IC2 MW Band Coverage fL: L6 fH: TC3 Input: Antenna Output: Headphone Socket SW1 Band Coverage fL(2.3 MHz): L7 fH(7.3 MHz): TC5 SW1 Tracking fL(2.6 MHz): L4 fH(6 MHz): TC6 SW2 Band Coverage fL(7.3 MHz): L8 fH(22 MHz): TC7 SW2 Tracking fL(8.5 MHz): L5 fH(19 MHz): TC8 (Load resistance: 32 ohms) Specified value 76 kHz ± 200 Hz VR1 Instrument Connection Pin 13, Pin 21 and ground of IC2 Note: After preparing the test circuit shown in Fig. 7, connect the Pin 13, Pin 21 and ground of the IC2 with the test circuit, and measure the value. • Playback Amplifier Sensitivity Check Specified value Specified Value/ Adjusting Point Adjustment Point Specified Value MTT-118 Input: Antenna Output: Headphone Socket (Load resistance: 32 ohms) fL: L1 fH: TC1 fL(88.0 MHz): L2 fH(108 MHz): TC2 • VCO Frequency Pin 1 of CNS102 A: 104 ± 4 kHz B: 94 ± 4 kHz C: 100 ± 4 kHz Beat Cancel Test tape FM Band Coverage FM Tracking MW Tracking fL(600 kHz): L3 fH(1,400 kHz):TC4 Tape 1,2:VR102 3,000 ± 60 Hz Headphones Socket (Load resistance: 32 ohms) Adjustment Point Input: FM Antenna Output:Pin 9 of IC2 Test Stage • Tape Speed (Normal only) MTT-111 FM IF L9 FM Detection L10 • AM IF/RF • Head Azimuth Test Tape Instrument Connection Instrument Connection Pin 21 of IC2 Pin 13 of IC2 Speaker terminal (Load resistance: 8 ohms) D FET: 2SK212 (or Other 2SK Type FET.) G 10 pF S 1M ohm 0.1 µF 10K ohm TO FREQUENCY COUNTER Figure 7 VCO FREQUENCY TEST CIRCUIT –7– GX-CD1200W SW103 SW1 SW401 TC6 L7 TC5 SW1 TRACKING fH FM TRACKING fH MW TRACKING fH SW1 BAND fH COVERAGE fL L8 TC7 SW2 BAND fH COVERAGE fL L2 MW BAND COVERAGE fL TC4 TC3 TC2 TC1 FM TRACKING fL L6 MW BAND COVERAGE fH fH FM BAND fL COVERAGE TC8 L1 IC1 fH SW2 fL TRACKING CF1 FM IF AM IF L5 L9 L11 12 CF3 9 1 CF2 L4 SW1 TRACKING fL L3 MW TRACKING fL IC2 21 24 13 VCO L10 FM DETECTION VR1 MAIN PWB MAIN PWB CNP103 IC502 Q603 TAPE SPEED VR102 CNP501 SPEAKER TERMINALS Figure 8 ADJUSTMENT POINTS –8– GX-CD1200W CD SECTION Since this CD system incorporates the following automatic adjustment function, when the pickup is replaced, it is not necessary to reajust it. Since this CD unit does not need adjustment, the combination of PWB and laser pickup unit is not restricted. TEST MODE Start While holding down the "PLAY" button, move the FUNCTION/POWER switch to "CD". (To serial No.006XXXXX) While holding down the "STOP" button, move the FUNCTION/POWER switch to "CD". (From serial No.007XXXXX) Note 1. When the CD LID switch is in the OFF position, (CD LID is open) the unit will be able to enter the test mode. However, can use the "UP/CUE" and "DOWN/REVIEW" button only. 2. You can only move the pickup. 3. The LCD display should be the same as it is for normal CD operations. Operation The use of the "UP/CUE" button will move the pickup to the outermost position. The use of the "DOWN/REVIEW" button will move the pickup to the innermost position. LCD MODE After connecting of the 10kΩ resistor between IC802 27 pin and GND and holding down the "PLAY" button, move the FUNCTION/POWER switch to "CD". Start Display LASER LIGHTING CONFIRMATION 1. Remove the front cabinet according to the disassembly method. 2. Short the TP of the Figure 9 to turn on the CD LID SW 810. 3. While holding down the "PLAY" button, move the FUNCTION/POWER switch to "CD". 4. Open the CD LID and press the PLAY button. The laser lights up for a few seconds. (At this time, the pickup lens moves up and down and adjusts the focus to check if there is a disc or not.) CD CONTROL PWB-C2 R847 R848 SW801 PLAY/ PAUSE SW804 REVIEW/ TRACK DOWN R849 SW802 STOP FW801 SW803 CUE/ TRACK UP LCD801 10 1 8 7 6 5 4 3 2 1 SWITCH PWB-C3 FW801 1 FW1 1 R846 12 100 1 C824 5 10 R844 R839 90 15 85 75 C823 1 C825 2 25 30 31 35 40 IC802 45 55 R835 R865 60 L801 C840 C843 R832 C837 Figure 9 –9– 11 1 R840 X801 C842 Q803 R858 3 2 1 Q804 C852 C845 R836 81 80 70 65 C850 C858 C844 95 20 R863 C848 2 C847 10 R861 1 2 3 P804 R822 C851 C853 C849 R857 L803 C846 C855 L802 SW810 OPEN/CLOSE R821 TP CD SERVO PWB-C1 17 4 14 15 16 13 6 5 4 3 CNS804 GX-CD1200W BI804 L-CH 2 0V(9V) 0V 1 0V 7 IC151 TA2011S MIC AMP. 3 1.3V 2 0V 4 1.9V 5 C33 3.3/50 C32 0.0082(ML) AM/FM VCO MO/ST R-CH MPX IN L-CH AM IN GND SW2 FM MW SW1 SW2 C41 1/50 R182 1K R184 330K R20 10 2.7V 0.9V 0.3V Q182 KTC3199 GRAPHIC EQUALIZ R127 22K R129 150K R130 150K +B CD TUNER R128 22K SW501-A FUNCTION SELECTOR CD TUNER TAPE C42 0.022 R-CH SW501-B FUNCTION SELECTOR D154 DS1SS133 R172 10K MIC R170 33K R177 1K C159 47/25 R171 33K D162 DS1SS133 C160 22/16 0V R111 22K NF MATAL OUT 2 C104 470P C102 470P PRE OUT R115 680 R113 120K A/B VCC MIX OUT GND1 C112 0.015 (ML) R110 6.8K REC OUT REC NF REC IN M/N REC OUT REC NF REC IN 8 9 10 11 12 C122 330P R124 10K R114 120K R116 680 C305 0.0015 (ML) C306 390P C304 0.022 C303 0.0056 (ML) C302 0.0022 (ML) (0.1V) R304 10 0V R131 1.2K ALC GND R132 1.2K C126 4.7/50 C124 0.01 R134 82K C120 R118 0.033 330K (ML) Q5 KT SW +B ( ):RECORD (3V) R302 R 100 R306 R305 47 27K (0.7V) L301 BIAS OSC. 1 R112 22K Q301 KTC3203 Y BIAS OSC. R301 330 R511 10K P SW101-E RECORD/ PLAYBACK C301 100/10 SW102 BEAT CANCEL A C138 0.0015(ML) Q601 KRC102M R133 82K 13 R120 100 C132 120P R136 10K L104 22mH 0V 2 9V 3 C125 4.7/50 C121 330P 14 R123 10K C114 4.7/50 R102 100 R119 100 15 6 7 3 4 5 C108 R106 330P 180K R122 R108 10K 10K +B C119 0.033 (ML) C123 0.01 R117 330K C117 10/16 C115 4.7/50 CH1/A CH1/B 16 C118 10/16 MATAL PRE OUT OUT C128 2.2/50 NF 17 C129 22/16 CH2/B 18 C116 4.7/50 CH2/A C127 330/10 C109 47/10 R101 100 C103 470P 22 1 21 R105 180K 20 19 23 C106 330P C134 150P R107 10K 24 R P R P SW101-D SW101-C SW101-B SW101-A R P R P C133 150P R100 150 C113 4.7/50 C111 0.015 R109 (ML) 6.8K C107 330P R174 22K +B (0V) (0.7V) Q156 KTC3199 GR LINE AMP. IC101 TA8189N RECORD/PLAY AMP. SW101-A~D RECORD/ PLAYBACK B SW501-C FUNCTION SELECTOR CD TUNER TAPE D158 DS1SS133 D152 DS1SS133 R135 10K CNP101 CNS101 Q153 KTC3199 GR MIC AMP. R173 10K C137 0.0015(ML) 1 2 3 CNP102 C158 47/25 D163 HIGH DS1SS133 NORMAL +B C105 330P C307 150P R169 10K R161 1M C101 470P C +B ( ):RECORD L103 22mH 1 2 3 4 SW103-A DUBBING SPEED/MIC R168 10K 0V(0.7V) C155 10/16 R154 560 D165 DS1SS133 D164 DS1SS133 ( ):HIGH R151 2.2K SW504-B TAPE2 DIRECTION +B R303 100 MAIN PWB-A1/VOLUME PWB-A3/FINE TUNING PWB-A4 H • NOTES ON SCHEMATIC DIAGRAM can be found on page 18. 1 C184 220P TAPE C43 220P SW101-F BAND SELECTOR R P R166 560 0V(0V) 0V(0V) C154 47/10 B CNS102 R17 2.7K C157 1/50 C110 47/10 C151 0.33/50 R152 4.7K A ERASE HEAD TAPE1 RECORD/PLAYBACK HEAD TC7 +B 6V 6 C156 100/10 TAPE2 PLAYBACK HEAD SW504-A TAPE2 DIRECTION R-CH 47 R11 47 R165 10K C131 120P G MW SW1 D156 DS1SS133 0V(0V) 3 MIC151 BUILT-IN MICROPHONE 1 2 3 4 R18 2.7K ( ):CD FUNCTION 0V(9V) C152 10/16 L-CH C40 1/50 R16 10K +8V(SERVO) E SIDE-A R-CH SIDE-B 11 C38 0.012 (ML) +B FM TC5 C26 0.022 0.9V 1 2 3 C182 1/50 R1 220 R1 220 D-GND R153 2.2K B 10 TP1 VCO 76KHZ C183 220P R351 47K A-GND Q154 KRA102M MIC AMP. SIDE-A L-CH SIDE-B 0.3V R181 1K 13 12 GND(A) J151 MIC JACK F 9 R13 100 C30 0.022 R352 47K R-CH 14 SW1-F BAND SELECTOR FM MW SW1 SW2 R10 C15 0.022 15 L7 SW1 OSC. C27 0.0047 R19 15K N.C. C37 0.012 (ML) C39 1/50 R15 10K R12 1K 2 C29 22/16 TC3 C21 5P (UJ) R353 27K 1 A FM DET 1 L8 SW2 OSC. R354 27K 16 8 CF3 3 455KHz AM IF AM IF TC8 FINE TNNING 17 7 VCO C36 0.0015 L-CH L3,4 MW/SW1 BAR ANTENNA C34 R14 470P 100K C35 3.3/50 DET OUT IF AD 7V SW1-E C19 BAND SELECTOR 330P FM C14 MW 5P(CH) SW1 SW2 C20 0.0022 TC9 18 Q181 KTC3199 G GRAPHIC R183 EQUALIZE 330K C181 2.7V 1/50 0.9V FM MONO VR1 10KB +B C25 0.022 R121 10K D 6 L6 MW OSC. L4 SW1 L5 SW2 ANTENNA CNP804 TO CD SERVO PWB P13 11-G 5 L11 VC3 6 5 4 3 2 1 4 +B 3 SW1 CNS804 6 5 4 3 2 1 AGC IC2 LA1805 FM/AM IF MPX. 2 TC6 SW2 19 21 C24 0.022 CF2 FM IF SW1-D BAND SELECTOR 20 AM IF AM OUT IF AD STB 22 2 SW1 SW2 MW L10 AM RF 23 C9 0.022 TC4 SW1-C BAND SELECTOR FM C 24 1 C6 0.0047 SW2 C31 0.0047(ML) R8 3.9K R9 12K 1 3 FM IF FM MW FM DETECTION C17 0.022 R5 100 R3 47 L3 MW FM STEREO SW1-H BAND SELECTOR C7 0.0047 C18 10/16 L9 C8 0.022 SW1-B BAND SELECTOR FM MW SW1 VC4 L1 FM OSC. C23 220/10 C22 0.022 SW1-G BAND SELECTOR OSC R1 10 0V TC1 D2 DS1SS133 D1 DS1SS133 5 C10 15P(CH) R2 33 VC2 B 8 6 VC1 C4 24P (CH) L2 9 C2 5P(CH) FM TRACKING TC2 SW2 C12 3P(CH) C11 22P(CH) MW SW1 4 1.6V 3 7.2V 2 C5 0.001 7.2V 1.6V FM 7.1V SW1-A BAND SELECTOR MIX 1 SW1 COV SW103-B FM MODE R7 820K C13 0.022 RF AMP 0.9V ROD ANTENNA(253) R4 330K 7 6.4V AM MIX IC1 TA7358AP FM FRONT END CF1 FM BAND PASS FILTER 1 2 3 A fH TC6 fL L4 SW1 TRACKING RECORD SIGNAL PLAYBACK SIGNAL MW/SW1 SIGNAL AM OSC FM IF IN FM SIGNAL 2 3 4 Figure 10 SCHEMATIC DIAGRAM (1/4) – 10 – 5 6 GX-CD1200W GRAPHIC EQUALIZER PWB-A2 C185 1/50 2.7V C203 1/50 R203 2.2K R187 3.9K R255 120 GRAPHIC EQUALIZER VR203 VR204 VR205 100K(A) 100K(A) 100K(A) (500Hz) (2KHz) (10KHz) X-BASS VR202 50K(A) (100Hz) 7 C253 0.022 C259 0.0039 (ML) 5 4 3 2 1 LED257 C257 47/25 39K +B 9 8 R253 R183 330K C181 1/50 0.9V IC202 LB1403N LEVER METER DRIVER R251 C251 6.8K 1/50 Q181 KTC3199 GR GRAPHIC EQUALIZER fH TC1 FM BAND COVERAGE fL L1 fH TC3 MW BAND COVERAGE fL L6 SW2 BAND fH TC7 COVERAGE fL L8 fH TC8 fL L5 SW2 TRACKING LED259 fH TC2 fL L2 FM TRACKING LED255 fH TC4 fL L3 MW TRACKING LED253 SW1 BAND fH TC5 COVERAGE fL L7 6 R257 10K fH TC6 fL L4 C255 10/16 R259 120 0.3V R207 4.7K 18 R202 1K R127 22K C202 4.7/50 16 14 12 C206 0.01 (ML) C222 4.7/50 10 8 C210 0.082 (ML) C256 10/16 LED1 STEREO VR205 VR204 VR203 VR202 100K(B) 100K(B) 100K(B) 50K(B) (10KHz) (2KHz) (500Hz) (100Hz) GRAPHIC X-BASS EQUALIZER R206 3.3K 1K +B LED501 R520 10K A : 0.8V B : 0.2V A : 0V B : 0.7V R521 10K R260 120 LED501,502 POWER DIRECTION LED502 R519 1K R204 C204 2.2K 1/50 R128 22K C254 0.022 R518 R208 3.3K R212 1K +B C260 0.0039 (ML) C218 0.47/50 C214 0.33/50 1 LED260 2 2 LED258 4 6 R252 6.8K 1 LED254 3 3 LED256 5 4 6 R258 10K 7 R254 39K C211 0.0015 9 11 C207 5.9V 470P IC201 BA3822LS GRAPHIC EQUALIZER 13 6.5V 5.9V 20 15 5 C252 1/50 LED401 SURRUND R180 560 22 17 7 9 8 C220 0.039 (ML) 0V 24 19 5.9V 6.5V Q182 KTC3199 GR GRAPHIC EQUALIZER 21 (ML) 23 (ML) R200 330 C200 100/10 R256 120 C205 0.01 (ML) C209 0.082 (ML) C213 0.33/50 (ML) +B C186 1/50 0.3V C217 0.47/50 C215 0.0056 C180 100/10 0.9V IC203 LB1403N LEVER METER DRIVER (ML) C216 0.0056 R188 3.9K R211 1K C212 0.0015 2.7V C201 4.7/50 R201 1K C221 4.7/50 R186 220 C219 0.039 (ML) C184 220P 2.6V 2.6V 4.4V 6.5V 6.5V 5.9V 5.9V 6.5V 6.5V 5.9V 5.9V 6.5V 6.5V 5.9V Q505 KTC3199 GR LED CONTROL 0V +B R440 470 +B SW401 SURROUND +B 5 R404 10K 3.8V 3.8V 3 0V +B 9V OUT IC501 3 KA7809AP 1 C506 2 IN 0.022 0V C505 47/16 Q602 KRA102 M 0V SWITCHING3 8.1V 100 C508 100/16 0V(0.7V) R511 10K R512 10K 0V(0V) L501 47µH 0V(7.9V) C511 0.022 13 L-CH 6 -OUT1 0V 3 C420 4.7/50 14.3V C424 1 47/25 0V R-CH -OUT2 5 9 + – – + R435 C427 2.2 0.1(ML) C426 0.1(ML) R434 2.2 L-CH SP401 WOOFER 8 Ohm L-CH R-CH SP402 WOOFER 8 Ohm 0V 6.9V 11 8 7 6.4V 15V VOLUME 6.9V 10 4 Q404 KTC3199 GR POWER MUTE 6.9V 12 R-CH R436 C428 2.2 0.1(ML) SP404 TWEETER 8 Ohm 15V R431 27K C429 10/16 C433 0.022 R437 120 C513 1/50 C510 3300/25 C601 0.022 8.5V (6.3V) R516 3.6K R515 120 + – B 1 2 3 4 5 6 7 8 9 CNS103 A J401 HEADPHONES JACK AC110V-127V AC220V-240V D651 TS4B03GM 1 2 3 4 5 6 7 8 9 Q504 KTA1271 Y SWITCHING (7.9V) 1 2 SW501-D FUNCTION SELECTOR IN R438 120 SW601 VOLTAGE SELECTOR POWER PWB-A7 1 2 8.5V(8.5V) VR102 470 TAPE SPEED R441 15K C423 10/16 C430 10/16 15V IC502 3 KA7809P 1 C514 2 1/50 C509 0.022 0V Q503 R514 KTC3199 GR 100K SWITCHING 7.9V 0.7V (0V) R416 3.3K 0V R433 2.2 SP403 TWEETER 8 Ohm +B OUT 9V Q502 KTC3199 GR SWITCHING R426 1K C425 0.1(ML) 0V 15V DZ601 DZ8.2BSB C602 100/10 R513 10K C414 0.001 (ML) R428 4.7K 14 +OUT2 R601 270 R602 ( ):HIGH SPEED 0.7V(0V) C416 0.15 VR401 (ML) 50K(B) 6.9V +OUT1 2 0V +B 7.5V 0V 0.6V 15V Q603 KTD2058 Y VOLTAGE REGULATOR C603 0.022 4 0V R429 100K R420 3.3K 15V 2 1 C604 220/10 C410 1/50 1 IC401 KIA4558P OPE AMP. 2 3.8V C404 10/16 C418 22/16 R418 22K R410 12K 0V R427 4.7K 0.6V R419 3.3K C412 47/10 C408 4.7/50 C415 0.15 (ML) IC402 LA4663 POWER AMP. C419 4.7/50 R425 1K CNS601 C402 0.0068(ML) +B R413 10K C407 4.7/50 R406 2.7K R408 12K R417 22K CNP103 R402 100K R409 12K R412 10K R407 12K C406 0.0033 C405 0.0033 (ML) (ML) R401 100K R405 2.7K VOLUME C413 0.001 (ML) CNP601 R403 10K 6 R415 3.3K C411 47/10 C401 0.0068(ML) 3.8V IC401 KIA4558P 8 OPE AMP. C409 3.8V 1/50 7 R442 15K 7.5V Q403 KTC3199 GR POWER MUTE 3.8V VR401 50K(B) R411 330 C403 10/16 CNP501 SPEAKER TERMINALS R182 K R184 330K R185 220 R205 4.7K C208 470P C182 1/50 C183 220P 6.9V 3.2V 3.2V 4.4V 1 C652 0.022 M501 MOTOR T601 POWER TRANSFORMER C651 0.022 SO601 AC SOCKET AC110V-127V/ AC220V-240V, 50/60Hz C654 0.022 C653 0.022 M F601 T4A L 250V SW901 TAPE1 MAIN SW902 TAPE2 MAIN SW903 TAPE2 PLAY TERMINAL B PWB-A6 SW904 TAPE2 DIRECTION TERMINAL A PWB-A5 BATTERYS DC 15V ["D" SIZE (UM/SUM-1, R20 or HP2) battery x 10] 0V(0V) IC501,502:VOLTAGE REGULATOR 7 8 9 10 Figure 11 SCHEMATIC DIAGRAM (2/4) – 11 – 11 12 GX-CD1200W A FW802 ( ):STOP SW810 OPEN/CLOSE 4 3 3 F 2 2 2 C 1 1 1 B F C GND 23 0V IC801 R895 68K R893 68K R892 56K R891 68K 2.1V FG FOPD VR LD 2 3 3 4 4 4 5 5 5 6 6 7 7 7 8 8 8 FC- 7 LDO 2.5V (0.3V) 8 SEL 2.8V 9 TEB 4.3V 10 2VRO 11 TEN 2.1V PU-IN GND 6 5 4 3 2 1 6 5 4 3 2 1 21 RFGC 20 RFGO 19 0V 0.1(ML) C818 56P 2.1V 18 RFRP 17 VRO 16 FEN 15 2.1V FEO 14 12 SBAD 13 10 2.1V C801 0.1 C863 47/10 2.0V (1.1V) LD R +B C822 0.047 C841 0.047 C843 47/10 C814 0.047 BI803 6 5 4 3 2 1 DM+ C834 470P 2 DM- 3 FM+ C835 470P C836 0.047 (ML) FOO FMSLT+ TRO +B C807 0.047 N.C. G RES 5V 2.1V 2.1V 3.3V 6.7V C89 220 +B 5V(5V) 2.2K R852 3.4V 0V 0V 0V 3V 3.6V R851 2.2K 2.1V C805 0.022 2.2V 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 +B 5V REG IN CD VIN3 VIN2 VG2 VO2+ VO2- GND GND GND VO1- VO1+ VG1 VIN1 N.C. REG OUT VG3 VO3+ VO3- GND GND GND VO4- VO4+ VG4 VIN4 VCC VREF MT VCC 92LHPC1LXASY QCNWN0032BGZZ NOT USED NOT USED VRD-ST2CD683J VRD-ST2CD563J VRD-ST2CD683J VRD-ST2CD683J VRD-ST2CD683J VRD-ST2CD563J 7.4V 92LHPC1LASY QCNWN0027BGZZ VCQYKA1HM103K VRD-ST2CD222J NOT USED JUMPER JUMPER NOT USED JUMPER JUMPER 0.9V PICK-UP UNIT BI802/CNS802 C801 R802 R891 R892 R893 R894 R895 R896 IC803 LA6541D FOCUS/TRACKING/SPIN/SLED C806 220/10 F From serial No.00504991 6.8V (6.8V) Q802 KTA1271 Y VOLTAGE REGULATOR FMO DMO +B +B CD SERVO PWB-C1 H • NOTES ON SCHEMATIC DIAGRAM can be found on page 18. 1 2 3 4 Figure 12 SCHEMATIC DIAGRAM (3/4) – 12 – C837 0.047 (M C838 0.047(M C839 0.047(M N.C. N.C. 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 To serial No.00404990 C854 R 0.0068 VR CD MOTOR PWB-B SERIAL NO. +B 3.2V (1.1) 2.1V TEO 9 2.2V C819 RFIS 2.1V PD SLT- SW702 PICKUP IN AGCI 0V R853 2.2K SL+ SL- – 3.6V (4.4V) 2.1V + MDI C820 0.1 (ML) R807 1K 8 GND 7.4V M 6 FC+ 2.1V SP- M801 SLED MOTOR CNS803 CNP803 – SP+ E TNI C813 47/10 + M 5 0.18V (0V) TR- PICK-UP UNIT M802 SPINDLE MOTOR 2.1V (2.1V) 3.3V D 2 3 6 TRVR1A 2 TPI 7.4V(7.5V) F+ 1 FPI 4 3.3V FO+ TR+ 1 3 2.1V (2.1V) 2.1V 1 R+ RFO 22 4.8V RTR+ R806 2.7K 1.6V (0.3V) FNI 2.1V R811 22K C4A R894 68K BI801 C CNS801 2/1VCC 2 R805 39K C832 47/10 4 3 VCC C842 0.047 4 A 2.1V RFN 24 1 C804 2P(CH) 5 5V 2.1V 5 R896 56K 3.3V 5 E C825 47/10 C8 47 82K C821 47/10 6 R803 7 6 3.6V (4.4V) 0V 3.3V B 7 6 C817 100/10 C802 0.022 C816 0.022 R804 68K 0V E A 7 +B C815 47/10 0V C2A R801 22 2.1V B C3A MON SERVO PRE AMP. 4.3V(5V) 0.2V(1.5V) BI802 LD CNS802 +5V VCC R802 IC801 2.2K TA2109F Q801 KTA1266 GR SWITCHING SWITCH PWB-C3 5 6 GX-CD1200W C825 47/10 +B +B 0V 0V 0V 0V 0V 0V 0V 0V 5V TEST0 ADIN2 27 0V 55 AVSS 5V ADIN1 26 2.1V 56 SLCO 0V P3-0 25 2.1V 57 RFI 5V P1-3 24 5V 58 AVDD 0V P1-2 23 2.1V 59 RFCT 0V P1-1 22 N.C. 2.1V 60 RFZI 0V P1-0 21 N.C. 2.7V 61 RFRP 0V MVSS1 20 2.3V 62 FEI 2.9V 63 SBAD TEI 65 TEZI 2.1V 66 FOO 2.1V 67 TRO 2.1V 68 VREF 6 19 P8-3 18 0V CD LID SW 17 0V CDSEL1 16 0V CDSEL0 15 14 N.C. 2.5V SEG13 13 N.C. RFGC 2.5V SEG12 12 N.C. TEBC 2.5V SEG11 11 N.C. 2.5V SEG10 10 N.C. 69 70 71 FMO 2.1V 72 DMO 4.1V 73 2VREF 2.5V 74 SEL 5V 75 VDD2 0V 76 0V 77 2.1V 2.6V 5V 15 9 N.C. 2.5V SEG8 8 N.C. 2.5V SEG7 7 N.C. 2.5V SEG6 6 N.C. VSS2 2.5V SEG5 5 XVSS 2.5V SEG4 4 78 XI 2.5V SEG3 3 79 XO 2.5V SEG2 2 80 XVDD 2.5V SEG1 1 COM2 COM1 MVDD MVSS MXI MXO INTR HOLD N.C. N.C. RESET DVSL RO LO 16 17 SW801 PLAY/ R847 R848 PAUSE 1K 2.2K R822 22K R849 6.8K LCD801 L802 10µH 8 7 6 5 4 3 2 1 N.C. COM4 4 COM3 2.5V SEG9 14 C824 0.1(ML) R861 3.3K 2.5V SEG14 11 2.1V R865 1K IC802 TC9457F0 SERVO/SIGNAL CONTROL 1 2.1V C845 0.047 C860 0.0015 7 R844 3.3K SW804 CUE/ TRACK UP 64 2.1V MVDD1 0V 5V 5 R863 3.3K SW803 REVIEW/ TRACK DOWN TEST1 TEST2 TEST3 TEST4 TEST5 /HSO SPCK SPDA COFS 28 5V 3.3K 3.3K 3.3K 2.3V 2.3V 2.3V 2.3V 5V 0V 0.3V N.C. N.C. 5V 5V 0V 5V 0V 0V 0V +B C847 2.5V 22/16 0V 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 2.4V XL801 3 16.93 MHz DOUT 0V(5V) MUTE VCOF R832 R833 R834 1 SBSY PVREF 54 SW802 STOP 2.5V 0.4V 0V 5V 5V 53 1.5V 2.1V 2 SBOK 2.1V 3.3K R840 10 VDD1 29 R831 C834 470P VSS1 PDO 30 PU IN 13 12 DVRL 3.3K 10K C840 0.047 C837 0.047 (ML) C838 0.047(ML) C839 0.047(ML) PUSEL2 5V 2.1V +B 835 70P 836 047 L) 0V LPFO DVSR C842 0.047 C841 .047 LPFN 52 DVDD R829 R830 1K R821 22K 51 4.7V C854 R812 0.0068 10µH 2.1V DVRR C833 0.033 (ML) P2VREF TMAX C829 0.0047 R828 10K C863 7/10 N.C. N.C. L803 2.1V C848 2.5V 22/16 2.3V C832 47/10 C830 0.01(ML) +B N.C. N.C. N.C. N.C. N.C. N.C. N.C. 2.1V 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 C827 R827 0.015 15K (ML) C828 0.0027 0V R826 220K 4.2V 2.1V R820 47K 1.7V +B C823 0.022 R824 10K 2.5V +B R846 330 C826 47P C844 100/10 C894 0.022 R836 15K +B C893 220/10 L801 0.82µH C850 C849 120P 120P C853 0.022 C852 3.3/50 FW801 R835 15K C855 0.022 C846 2.2/50 R839 47K C851 3.3/50 CD CONTROL PWB-C2 Q804 +B KRC102M MUTING 3 0V(5V) 0V 2 1 0V C858 0.022 R858 R857 5.6K 5.6K 3 0V 2 1 0V 0V(5V) Q803 KRC102M MUTING CNP804 R-CH GND(A) C859 0.0027 L-CH A-GND D-GND +B B+ 6 5 4 3 2 CNS804 FROM MAIN PWB P10 1-D 1 • The numbers 1 to 17 are waveform numbers shown in page 19. 7 8 9 10 Figure 13 SCHEMATIC DIAGRAM (4/4) – 13 – 11 12 GX-CD1200W TO CD SERVO PWB P17 12-D CNP804 SW102 BEAT CANCEL C B A C301 R113 C115 C160 R121 R115 C121 R117 R131 R119 C123 C125 L103 C113 R122 IC101 F R412 C409 R173 C405 R411 C412 R417 R413 C407 R407 C403 R406 C404 R416 C411 5 C401 R401 BK C151 E R405 R409 8 R403 1 C402 SW501 FUNCTION SELECTOR A B IC401 R402 R154 C406 R418 R153 R151 C305 R306 C304 R302 C303 C302 C136 C408 C410 C154 R415 WH D C VOLUME PWB-A3 CD/LINE SW40 SURRO VR401 VOLUME B RADIO TAPE MIC 151 BUILT-IN MICROPHONE 3 Figure 14 WIRING SIDE OF P.W.BOARD (1/4) – 14 – 5 6 C252 R252 R256 R419 C257 R255 C253 R251 C260 A R518 C259 R519 4 FW1 1 R253 C251 R201 R202 C255 R257 4 1 2 C254 R521 R520 C221 R200 LED257 C207 H IC202 1 2 3 4 5 6 7 8 9 LED259 R259 VR205 C222 C211 C201 R211 2 C204 C205 C202 C213 C209 C217 R207 24 C200 LED501 C206 C214 20 C416 R204 LED253 C413 C415 R420 C203 C215 15 C219 VR202 IC201 R212 10 LED502 R206 VR204 1 5 VR203 C218 C220 G R205 C208 R208 E C B LED255 C210 C212 C216 R203 Q505 C414 1 C124 C126 C129 C120 R123 R120 R112 C118 C138 R116 R136 R118 C116 C122 R114 4 R410 J151 MIC JACK GL D R C1 R1 C109 4 3 2 1 BK R408 C159 R165 C602 R181 R127 D154 BK C CNP102 WH R129 R152 WH C105 R101 C103 C101 3 2 1 B D152 24 CNP101 C133 7 6 5 4 3 2 1 C152 R105 C107 SW101 C134 R C R107 20 5 R106 D163 D164 R166 R161 10 15 C132 Q181 D165 C156 J401 HEADPHONES JACK F L104 A R170 R168 C157 C158 Q154 R438 Q153 C429 R511 R183 C181 B C E 12 13 C108 1 C106 R102 C104 C102 C110 R110 C112 R104 R124 C184 Q182 C180 R185 C185 R187 C183 R180 R184 R186 R188 R182 D162 C426 R434 R133 C186 B C E C128 R128 C155 R437 C114 R134 4 C127 R108 3 2 1 R431 IC151 IC501 R425 R426 R130 C430 R132 C513 R404 C420 1 2 3 R111 C506 R177 E R352 R100 C514 C428 B C E Q602 C603 E C B 1 R169 C604 Q601 C607 3 2 1 C509 Q603 C505 L301 R351 IC502 C512 FW1 C425 R602 R174 R171 D156 C427 2 R601 D158 1 2 3 4 5 6 7 8 9 R442 C423 IC402 1 2 3 4 5 6 7 8 9 10 11 12 13 14 DZ601 3 2 1 CNP103 C418 1 CNS601 FROM POWER PWB P16 5-F R436 D B C E C182 CNP601 R428 R427 R429 C419 R435 R433 C433 R441 C424 C L501 C508 Q404 Q403 B C E 1 2 3 E C B C135 Q502 C510 R516 R515 C608 B C E R514 VR102 C601 E C B E C B R513 Q504 CK129 R512 B Q503 C511 BI804 Q301 6 R305 1 C307 R304 C306 CNS804 1 2 3 4 5 6 R301 MAIN PWB-A1 C131 CNP501 SPEAKER TERMINALS LED260 A LED258 GX-CD1200W W102 AT CANCEL C B A ROD ANTENNA SPRING (249) COLOR TABLE BR BROWN RD(R) RED L301 C305 ROD ANTENNA (253) R7 WH C34 C22 C23 C119 C32 R9 C31 R8 24 13 C36 15 20 IC2 R17 R3 C10 TC8 C12 C6 L1 VC1 C4 TC1 VC2 VC1 R11 WH TC5 TC3 C14 GY FW2 TC6 C19 C20 C27 C42 E F C D H G B A TC9 B CNS102 C30 ON R10 A SW401 SURROUND OFF SW1 BAND SELECTOR SW103 DUBBING SPEED/ MIC/FM MODE MIC NORMAL FM MONO HIGH FM MW SW1 SW2 CNS103 FM STEREO BR RD OR YL GR BL VL GR WH R254 R258 1 2 3 4 5 6 7 8 9 C256 LED1 YL YL 1 2 3 4 5 6 7 8 9 A TAPE 2 SW504 HEAD FLEXIBLE TAPE1 PWB DIRECTION B +- R260 A B LED254 LED256 LED401 C260 C252 R252 C254 R419 R256 IC203 LED260 BK FINE TUNING PWB-A4 VC3 C16 L7 RD C28 TC7 TC2 SW503 TAPE2 PLAY SW501A TAPE2 MAIN GRAPHIC EQUALIZER PWB-A2 BK 4 WH 3 RD 2 BK 1 R13 R440 R2 R1 TC4 R415 7 RECORD/PLAYBACK HEAD ERASE HERAD R4 L8 R173 R301 C13 C9 VC4 LED258 PINK 1 2 3 4 5 6 7 8 9 C21 L103 IC1 C7 C26 C415 BLACK PK L3,4 MW/SW1 BAR ANTENNA D1 C8 C5 C413 BK TAPE 1 D2 C405 R411 C412 R417 R413 R412 409 GRAY L5 L2 2 VIOLET R5 C15 CF1 1 2 3 L6 F BLUE VL WHITE L4 SW1 L9 C2 R303 101 L11 R172 C131 1 CF3 1 2 3 D152 R109 C111 C105 R103 R101 C109 3 C24 CF2 3 2 1 C37 C25 R20 R14 R135 C137 R107 R105 C107 C41 R15 R12 GREEN BL GY C43 1 C38 E C B C39 GR WH(W) C29 5 12 C40 R18 Q156 C117 R121 R115 C160 R113 C115 C121 R117 10 R16 YELLOW C11 27 R131 R119 C123 C125 TP1 L3 MW C18 R353 C35 R351 C33 R354 R19 R352 ORANGE YL L10 VR1 C17 BK OR C M501 TAPE MOTOR SW502 TAPE1 MAIN PLAYBACK HEAD B A GR BK RD WH CNS101 RD GY WH 8 9 10 Figure 15 WIRING SIDE OF P.W.BOARD (2/4) – 15 – 11 3 2 1 12 GX-CD1200W A SO601 AC SOCKET AC110V-127V/ AC220V-240V, 50/60Hz TERMINAL A PWB-A5 SW601 VOLTAGE SELECTOR AC220V-240V AC110V-127V (251) (250) B BATTERYS DC15V ["D" SIZE (UM / SUM-1, R20 or HP2) battery x 10] OR C RD (251) TERMINAL B PWB-A6 T601 POWER TRANSFORMER D BK WH BL (237) RD E WH OR COLOR TABLE F BR BROWN RD(R) RED OR ORANGE YL YELLOW GR GREEN CNS601 RD GY GRAY WH(W) WHITE BK BLACK PK PINK C652 C651 VIOLET P14 1-D C653 BLUE VL CNP601 2 BK C654 G BL F601 T4A L 250V BK TO MAIN PWB 1 D651 POWER PWB-A7 H 1 2 3 4 Figure 16 WIRING SIDE OF P.W.BOARD (3/4) – 16 – 5 6 GX-CD1200W CD CONTROL PWB-C2 R847 R848 SW804 REVIEW/ TRACK DOWN R849 SW802 STOP SW801 PLAY/ PAUSE FW801 SW803 CUE/ TRACK UP LCD801 10 1 8 7 6 5 4 3 2 1 SWITCH PWB-C3 R839 90 C823 R821 1 25 30 31 35 40 45 55 L801 70 65 C843 R832 C837 IC803 20 16 Q802 E C B R801 R853 25 Q801 R807 R805 C820 R806 24 C804 12 8 5 7 6 BR BK BK BK BK BK BK BK C805 C813 1 WH WH WH WH WH WH BK 7 6 5 4 3 2 1 10 BI801 C807 C806 7 C822 R894 R893 R895 3 2 1 2 3 4 5 6 7 8 CNS801 8 COLOR TABLE BR BROWN RD(R) RED OR ORANGE YL YELLOW GR GREEN CD MOTOR PWB-B + M801 SLED MOTOR BL BLUE VL VIOLET GY GRAY WH(W) WHITE BK BLACK PK PINK F0027AW SW702 PICKUP IN SERIAL NO. + - CNP803 1 2 3 4 5 6 R802 R891 R896 R892 1 CNS803 BR 1 GY 2 GY 3 GY 4 GY 5 GY 6 CNS804 FROM MAIN PWB P14 5-A C821 20 15 IC801 10 5 1 6 5 4 3 2 1 9 C818 R803 13 C815 R804 B C E C802 15 10 C893 5 C894 1 C833 C819 C839 C836 C834 C835 C838 C854 C842 C829 R829 C827 C830 R852 R833 R834 R831 51 C828 R826 C863 C840 X801 60 50 11 1 R840 R830 R824 R827 R820 C826 C841 R851 30 IC802 81 80 C832 BI803 2 FW1 C825 R863 C845 R836 R865 85 75 CNP804 15 20 3 2 1 Q804 C852 R828 R844 C844 95 10 C850 C858 Q803 R858 C801 5 R835 R811 C814 C824 R846 12 100 1 C816 FW1 1 C848 10 R861 1 C817 2 C847 1 2 3 BI802 FW801 R812 R822 C851 C853 C849 R857 L803 C846 C855 L802 SW810 OPEN/CLOSE CD SERVO PWB-C1 17 4 14 15 16 13 M802 SPINDLE MOTOR PICK-UP UNIT BI802/CNS802 C801 R802 R891 R892 R893 R894 R895 R896 PICK UP UNIT 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 To serial No.00404990 From serial No.00504991 92LHPC1LASY QCNWN0027BGZZ VCQYKA1HM103K VRD-ST2CD222J NOT USED JUMPER JUMPER NOT USED JUMPER JUMPER 92LHPC1LXASY QCNWN0032BGZZ NOT USED NOT USED VRD-ST2CD683J VRD-ST2CD563J VRD-ST2CD683J VRD-ST2CD683J VRD-ST2CD683J VRD-ST2CD563J • The numbers 1 to 17 are waveform numbers shown in page 19. 7 8 9 10 Figure 17 WIRING SIDE OF P.W.BOARD (4/4) – 17 – 11 12 GX-CD1200W NOTES ON SCHEMATIC DIAGRAM • • • • • Resistor: To differentiate the units of resistors, The symbol as K and M are used: the symbol K means 1000 ohm and the symbol M means 1000 kohm and the resistor without any symbol is an ohm resistor. The resistor designated “Fusible” is a fuse type resistor. Capacitor: To indicate the unit of capacitor, a symbol P is used: this symbol P means pico-farad and the unit of the capacitor without such a symbol is microfarad. As to electrolytic capacitor, the expression “capacitance/withstand voltage” is used. (CH),(RH),(UJ): Temperature compensation (ML): Mylar type (S): Styrol type The indicated voltage in each section is the one measured by Digital Multimeter between such a section and the chassis with no signal given. Schematic diagram and Wiring Side of P.W. Board for this model are subject to change for improvement without prior notice. Parts marked with “ ” ( ) are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. REF. NO. DESCRIPTION POSITION SW1 BAND SELECTOR FM SW101 RECORD/PLAYBACK PLAYBACK SW102 BEAT CANCEL A SW103 DUBBING SPEED/MIC/ FM MODE MIC/FM MONO SW401 SURROUND ON SW501 FUNCTION SELECTOR CD/LINE SW601 VOLTAGE SELECTOR AC220-240V SW702 PICKUP IN OFF SW902 TAPE 2 MAIN OFF SW901 TAPE 1 MAIN OFF SW903 TAPE 2 PLAY OFF SW904 TAPE 2 DIRECTION A FRONT VIEW FRONT VIEW E C B E C B KTA1266 GR KTA1271 Y KTC3199 GR KTC3203 Y KRA102 M KTD2058 Y 333ID213 Figure 18 TYPES OF TRANSISTOR AND LED VOLTAGE IC2 (LA1805) PIN FM MW/SW PIN FM MW/SW 1 2 3 4 5 6 7 8 9 10 11 12 1.6V 1.6V 7.2V 0.5V 1.6V 0V 7.6V 0V 2.3V 2.3V 6.5V 0.9V 1.6V 1.6V 8V 0.8V 1.6V 0V 7.6V 0V 2.4V 2.4V 8V 0.9V 13 14 15 16 17 18 19 20 21 22 23 24 1V 2.2V 1V 1.7V 1.6V 1.6V 0.4V 7.2V 7.2V 0.5V 1.6V 1.4V 0V 1.8V 1.5V 1.7V 1.7V 1.6V 0.7V 8V 8V 1.6V 1.6V 1.6V IC101 (TA8189N) PIN PLAY REC PIN PLAY REC 1 2 3 4 5 6 7 8 9 10 11 12 0V 0V 1.3V 1.4V 1.4V 1.3V 0V 0V 1.8V 1.3V 0V 0V 0V 0V 1.3V 1.4V 1.4V 1.3V 0V 0V 1.8V 1.3V 0V 0V 13 14 15 16 17 18 19 20 21 22 23 24 0.9V 0V 1.3V 1.8V 1.4V 7.4V 1.4V 1.4V 1.4V 1.3V 0V 0V 0.9V 0V 1.3V 1.8V 1.4V 7.4V 0V 1.4V 1.4V 1.3V 0V 0V IC202/203 (LB1403N) PIN LED OFF LED ON 1 2 3 4 5 6 7 8 9 7.7V 7.7V 7.7V 7.7V 0V 7.7V 0V 0V 8.6V 1V 1V 1V 1V 0V 1V 2.4V 0V 8.6V – 18 – GX-CD1200W WAVEFORMS OF CD CIRCUIT NO DISC FOCUS SEARCH 1 STOP FO+ FO- SEL TRO 2 FMO 3 PLAY CUE 6 1 TEI 1 TRO 2 FMO 3 IC802 64pin SBAD 11 2 IC802 67pin RFO 15 3 IC802 71pin IC801 22pin STOP PLAY REVIEW 6 1 FEI TEI 1 TRO 2 FMO 3 IC802 64pin IC802 62pin RFGO 11 2 IC801 19pin IC802 67pin RFRP 15 3 IC801 17pin IC802 71pin STOP TEI PLAY TCD-782 TNO-02 PLAYBACK 16 1 IC802 64pin LO 1 RO 2 IC802 86pin TRO 2 SBAD 3 IC802 67pin 7 1 IC802 71pin IC802 63pin 11 15 3 FEI 6 TEI IC802 67pin IC802 62pin 10 11 2 STOP 9 PLAY IC802 64pin TEI 5 6 1 FEI 8 3 STOP IC802 64pin 7 DMO TOC IL IC802 62pin 5 2 IC802 72pin IC802 74pin 6 SBOK 14 3 FOCUS SEARCH 5 1 IC802 45pin IC803 21pin 4 13 2 IC803 20pin 3 TMAX IC802 50pin IC802 66pin 2 12 1 FOO PLAY 17 IC802 82pin IC802 63pin – 19 – GX-CD1200W TROUBLESHOOTING (CD SECTION) When the CD does not function When the CD section does not operate when the objective lens of the optical pickup is dirty, this section may not operate. Clean the objective lens, and check the playback operation. When this section does not operate even after the above step is taken, check the following items. Remove the cabinet and follow the troubleshooting instructions. "Track skipping and/or no TOC (Table Of Contents) may be caused by build up of dust other foreign matter on the laser pickup lens. Before attempting any adjustment make certain that the lens is clean. If not, clean it as mentioned below." Turn the power off. Gently clean the lens with a lens cleaning tissue and a small amount of isopropyl alcohol. Do not touch the lens with the bare hand. Dust gradually accumulates on the objective lens during use, and it may degrade performance. To avoid this problem, use a cleaning disc designed for CD optical pickup lenses. HOW TO USE 1. Using the brush in the cleaner cap, apply 1 or 2 drops of the cleaning fluid to the brush on the CD cleaner disc which has the mark next to it. 2. Place the CD cleaner disc onto the CD disc tray with the brush side down, then press the play button. 3. You will hear music for about 20 seconds and the CD player will automatically stop. If it continues to turn, press the stop button. CAUTION The CD lens cleaner should be effective for 30 - 50 operations, however if the brushes become worn out earlier then please replace the cleaner disc. If the CD cleaner brushes become very wet then wipe off any excess fluid with a soft cloth. Do not drink the cleaner fluid or allow it to come in contact with the eyes. In the event of this happening then drink and / or rinse with clean water and seek medical advice. The CD cleaner disc must not be used on car CD player or on computer CD-ROM drives. All rights reserved. Unauthorized duplicating, broadcasting and renting product is prohibited by law. Cleaning Disc PARTS CODE: UDSKA0004AFZZ Cleaning Liquid • The CD function will not work. The CD operating keys don't work. Check the power supply, 16.93 MHz clock, and reset terminal. Check the pickup-in switch (SW702) position. Check the Focus system. – 20 – GX-CD1200W • Laser failure. Is +7.5V applied to the emiter of Q802 ? Check the PWB pattern of Q603. No Yes Is +5V applied to the collector of Q802 ? Check the peripheral parts of IC803 and Q802. No Yes No Check the PWB pattern between collector of Q204 and pin 75 of IC802. No Check the PWB pattern between collector of Q204 and pin 1 of IC801. No Check the laser come on when pattern cut between pin 8 (SEL) of IC801 and pin 74 (SEL) of IC802. No Check the peripheral parts of IC801 and Q801. If it is normal, the optical pickup is faulty. No Check as stated in item "FOCUS SERVO SAWTOOTH WAVE FAILURE". Is +5V applied to the pin 75 (VDD) of IC802 ? Yes Is +5V applied to the pin 1 (VCC) of IC801 ? Yes Is +0V applied to the pin 74 (SEL) of IC802 ? Yes Is approx. 1.8V applied to the collector of Q801. Yes Check BI801/CNS801. If it is normal, the optical pickup is faulty. • Focus failure. Does the optical pickup move up and down when the disc is removed? Yes Is the following waveform ouput at the pin 62 (FEI) of IC802 when the disc is set? Check the periphery of IC801 and BI801/CNS801. Is it normal? No Yes Yes pin 62 The optical pickup is faulty. (FEI) pin 86 (FOO) pin 63 (SBAD) Is the waveform shown above input at the pin 63 (SBAD) of IC802? No Yes IC801 is faulty. – 21 – Check the pattern between pin 13 of IC801 and pin 63 of IC802. Check the periphery of IC801 and BI801/CNS801. GX-CD1200W • Focus servo sawtooth wave failure. Is sawtooh wave output to the pin 66 (FOO) of IC802 ? No IC802 is faulty. Yes 1.5~2.5sec Check the PWB pattern of IC803. Is +8.1V applied to the pins 1 and 30 (VCC) of IC803 ? No Yes Check the PWB pattern of IC803. Is sawtooth wave obtained between pins 20 and 21 of IC803 ? No Yes 1.5~2.5sec Is sawtooth wave obtained between pins 3 and 4 of BI801/ CNS801 ? (as shown above) Check the PWB pattern between BI801/CNS801 and IC803. No Yes BI801/CNS801 connection failure or optical pickup failure. • Spindle motor clv servo failure. Is following wave output to the pin 55 (AVSS) of IC802 when the Function is changed to "PLAY" from "STOP" ? No Check the procedure in "HF ERROR". If OK. IC802 is faulty. No Check the PWB pattern between pin 72 (DMO) of IC802 and pins 5 and 6 of IC803. If OK. IC803 is faulty. Yes DMO Is above wave obtained between pins 5 and 6 of IC803 ? Yes Is above wave obtained between pins 5 and 6 of BI803/ CNS803 ? Check the PWB pattern between BI803/CNS803 and IC803. No Yes BI803/CNS803 connection failure or optical pickup failure. – 22 – GX-CD1200W • Track search failure Does the sled motor run in FF/REW state when the CD TEST MODE is set? No Check as stated in item "SLED MOTOR OPERATION FAILURE". Yes Is the following wave output to the pin 67 (TRO) of IC802 during track search in normal playback? No IC802 failure. Yes TRO Is the following wave output to the pins 12 (TEO) of IC801 during track search in normal playback? No Yes TEO TEI Check the PWB pattern between pin 67 (TRO) of IC802 and pin 28 of IC803. Check the PWB pattern between pins 25 and 26 of IC803 and Optical pickup. If OK. Optical pickup failure. TEZI Is the above wave output to the pins 64 (TEI) and 65 (TEZI) of IC802 during track serch in normal playback? No Check the PWB pattern between pin 12 (TEO) of IC801 and pins 64 (TEI) and 65 (TEZI) of IC802. If OK. IC801 failure. No Check the PWB pattern between pin 22 (RFO) and 18 (RFIS), 17 (RFRP) of IC801 and pins 60 and 61 of IC802. If OK. IC801 failure. Yes Is the following wave output to the pin 60 (RFZI) and 61 (RFRP) of IC802 during track search in normal playback? Yes RFRP RFZI Normal. • Sled motor operation failure. Is following sled feed signal output the pin 71 (FMO) of IC802 when FF/REW key is pressed after the CD TEST MODE is sated? Yes FF IC802 is faulty. No REW FMO Is following sled feed signal input the pins 12 and 13 of IC803 when FF/REW key is pressed after the CD TEST MODE is seted? FF Yes No Check the PWB pattern between pin 71 of IC802 and pins 12 and 13 of IC803. REW SL ± Is sled feed signal output the pins 10 and 11 of IC803? No Check the peripheral parts of IC803. If OK, IC803 is faulty. Yes Is sled feed voltage applied between both terminals of sled motor? Yes No Check the BI803/CNS803. Check the CD mechanism (periphery of sled motor). If the sled motor does not run when DC2.0V is applied to both terminals of sled motor, the sled motor is faulty. • Sled servo failure. Is following sled signal output the pin 71 (FMO) of IC802 during playback? IC802 is faulty. No Yes FMO Normal. – 23 – GX-CD1200W FUNCTION TABLE OF IC IC802 VHiTC9457F0-1: Servo/Signal Control (TC9457F0) (1/4) Pin No. Port Name 1* 2 3 4 5 6* 7* 8* 9* 10* 11* (OT5)S1 (OT6)S2 (OT7)S3 (OT8)S4 (OT9)S5 (OT10)S6 (OT11)S7 (OT12)S8 (OT13)S9 (OT14)S10 (CLCK/OT15) S11 (DATA/OT16) S12 (SFSY/OT17) S13 (LRCK/OT18) S14 (BCK/S15) P8-0 (AOUT/S16) P8-1 (MBOV/S17) P8-2 (IPF/S18) P8-3 12* 13* 14* 15 16 17 18 Terminal Name Input/Output Function SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 Output Output Output Output Output Output Output Output Output Output Output SEG12 Output SEG13 Output SEG14 Output CDSEL0 Output Segment signal output to the LCD panel. Up to 72 segments in a matrix with COM1 to COM4 can be displayed. All of the S1 to S18 pins can be switched for output ports by a program. Also, the S15 to S18 pins each can be switched for I/O ports individually. When set for I/O ports, these pins become Nch open-drain output. Furthermore, the S11 to S14 and the P8-0 to P8-3 pins can be switched for use as CD signal (CLCK to IPF) input/output pins by a program. • CLCK: Subcodes P thru W data readout clock input/output. Selected between input and output by a command. • DATA: Subcodes P thru W data output. • SFSY: Playback system frame sync signal output. • LRCK: Channel clock (44.1kHz) output. It outputs a low for L channel and a high for R channel. Polarity can be inverted by a command. • BCK : Bit clock (1.4122MHz) output. • AOUT: Audio data output. • MBOV: Buffer memory-over signal output. It outputs a high when buffer overflows. • IPF : Correction flag output. When AOUT is C2 correction output, it outputs a high indicating that correction is impossible. CDSEL1 Output CD LID SW Output DOOR OUT Output 19 20 MVDD MVSS MVDD1 MVSS1 — — Power supply pins. Normally, apply a voltage of 4.5 to 5.5V to VDD. In a backup state (when the CKSTP instruction executed), the device's current consumption is reduced to 1µA or less, allowing for the supply voltage to be lowered to 2.0V. The device is reset and the program starts from address 0 when a voltage of 2.7V or more is applied to this pin when it is at 0V (power-on reset). 21* 22* 23 24 (K0)P1-0 (K1)P1-1 (K2)P1-2 (K3)P1-3 TRAY CLOSE TRAY OPEN PUSEL0 PUSEL1 Input Input Input Input 4-bit CMOS I/O ports. These ports can be set for input or output bit for bit by a program. These pins can be pulled up to VDD or down to GND by program. Therefore, they can be used as key input pins. Also, when they are set for I/O port, a change of state in this input can be used to clear the clock stop or wait mode. 25 26 27 28 29 (DCREF)P3-0 (ADin1)P3-1 (ADin2)P3-2 (ADin3)P3-3 (BUZR/ ADin4)P4-0 DISPLAY ADIN1 ADIN2 MUTE PU IN Input Input Input Input Input 5-bit CMOS I/O ports. These ports can be set for input or output bit for bit by a program. The P3-0 to P4-0 pins serve dual purposes as analog inputs for the internal 6-bit 4-channel A/D converters. The internal A/D converters can complete conversion in 6 instruction cycles using a successive approximation method. The required pins can be set for A/D analog input bit for bit by a program. P3-0 can be set for reference voltage input, and the internal power supply (MVDD) can be used for this reference voltage. The P4-0 pin serves dual purposes as a buzzer output pin. The buzzer output can be selected from 8 frequencies, 0.625 to 3kHz. Each selected frequency can be output in one of four modes: continuous, single, 10Hz intermittent, and 10Hz intermittent at 1Hz interval. Whether or not to use and how to control the A/D converter and buzzer all can be set by a program. In this unit, the terminal with asterisk mark (*) is open terminal which is not connected to the outside. – 24 – GX-CD1200W IC802 VHiTC9457F0-1: Servo/Signal Control (TC9457F0) (2/4) Pin No. Port Name 30 31* (S12)P4-1 (SO/S11/ SDA)P4-2 (SCK/SCL) P4-3 32* Terminal Name Input/Output PUSEL2 NC Input Input/Output NC Input/Output Function 3-bit CMOS I/O ports. These ports can be set for input or output bit for bit by a program. These pins serve dual purposes as input or output pins for the serial interface circuit (SIO). The SIO is a 2-wire/3-wire compatible serial interface. 4 or 8 bits of serial data, beginning with the MSB or LSB, are serially output from the SO/SDA, pin at each clock edge on the SCK/SCL pin, and the data on S11 or S12 pin is serially input to the device. The serial clock (SCK/SCL) allows selection between the internal (450/225/ 150/75 kHz) and external sources and a selection of the active edge, rise or fall. Moreover, since the clock and data can be output via Nch open-drain outputs, various, device controls and communication between controllers can be greatly facilitated. When an SIO interrupt is enabled, an interrupt is generated at completion of SIO execution and the program jumps to address 4. All inputs to SIO contain a Schmitt trigger circuit. 33 34 35 36 37 38 TEST0 TEST1 TEST2 TEST3 TEST4 TEST5 TEST0 TEST1 TEST2 TEST3 TEST4 TEST5 Input Input Input Input Input Input Test mode control input pins. The test mode is selected when these pins are set high and normal operation is selected when they are low. 39* 40* 41* 42* (OT19)/HSO (OT20)SPCK (OT21)SPDA (OT22)COFS /HSO SPCK SPDA COFS Output Output Output Output 43* DOUT DOUT Input/Output Digital output pin. 44* SBSY SBSY Input/Output Subcode block sync output pin. It outputs a high at the S1 position when subcode sync is detected. 45* SBOK SBOK Input/Output Subcode Q data CRCC determination result output pin. It outputs a high when CRCC check is found OK. 46 47 VDD VSS VDD1 VSS1 Input/Output Input/Output CD unit's digital block power supply pins. Normally, apply 5V to VDD. When not using a CD (CD off), this power supply can be turned off, with only the controller power supply kept active, so that the controller alone is operating. In this case, the CD off bit must be set to 1. When this bit is set to 1, pins 11 through 18 and pins 39 through 42 all are changed for output ports if they have been set for CD control signal input/output pins. 48 P2VREF P2VREF Input/Output PLL block-2 VREF pin. 49 PDO PDO Input/Output This pin outputs a phase error between EFM and PLCK signals. 50 TMAX TMAX Input/Output TMAX detection result output pin. Selected by command bit TMPS. Longer than preset period: Outputs P2VREF. Shorter than preset period: Low level (Vss). Within preset period: High impedance. 51 LPFN LPFN Input/Output Inverted input of low-pass filter amp. 52 LPFO LPFO Input/Output Output of low-pass filter amp. 53 PVREF PVREF Input/Output PLL block VREF pin. 54 VCOF VCOF Input/Output VCO filter pin. 55 AVSS AVSS Input/Output Analog block ground pin. 56 SLCO SLCO Input/Output DAC output pin for data slice level generation. 57 RFI RFI Input/Output RF signal input pin. 58 AVDD AVDD Input/Output Analog block power supply pin. 59 RFCT RFCT Input/Output RFRP signal center level input pin. 60 RFZI RFZI Input/Output RFRP zero-cross input pin. 61 RFRP RFRP Input/Output RF ripple signal input pin. 62 FEI FEI Input/Output Focus error signal input pin. CD control output pins. • /HSO: Playback speed mode output. High = normal speed; Low = double speed. • SPCK: Processor status signal readout clock output (176.4kHz) • SPDA: Processor status signal output. • COFS: Correction system frame clock output (7.35kHz) These pins can be switched for output ports by a program. In this unit, the terminal with asterisk mark (*) is open terminal which is not connected to the outside. – 25 – GX-CD1200W IC802 VHiTC9457F0-1: Servo/Signal Control (TC9457F0) (3/4) Pin No. Port Name 63 SBAD SBAD Terminal Name Input/Output Input/Output Subbeam add signal input pin. 64 TEI TEI Input/Output Tracking error input pin. This input is read when tracking servo is on. 65 TEZI TEZI Input/Output Tracking error zero-cross input pin. 66 FOO FOO Input/Output Focus equalizer output pin. 67 TRO TRO Input/Output Tracking equalizer output pin. 68 VREF VREF Input/Output Analog reference power supply pin. 69 RFGC RFGC Input/Output RF amplitude adjusting control signal output pin. It outputs 3-level PWM signals. (PWM carrier = 88.2kHz) 70 TEBC TEBC Input/Output Tracking balance control signal output pin. It outputs 3-level PWM signals. (PWM carrier = 88.2kHz) 71 FMO FMO Input/Output Focus equalizer output pin. It outputs 3-level PWM signals. (PWM carrier = 88.2kHz) 72 DMO DMO Input/Output Disc equalizer output pin. It outputs 3-level PWM signals. (PWM carrier = DSP block 88.2kHz, synchronized to PXO) 73 2VREF 2VREF Input/Output Analog reference power supply pin. (2 x VREF) 74 SEL SEL Input/Output APC circuit on/off signal output pin. When laser is on, this pin goes to a high-impedance state when UHS = low and outputs a high when UHS = high 75 76 VDD VDD VDD2 VSS2 Input/Output Input/Output CD unit's digital block power supply pins. Normally, apply 5V to VDD. When not using a CD (CD off), this power supply can be turned off, with only the controller power supply kept active, so that the controller alone is operating. In this case, the CD off bit must be set to 1. When this bit is set to 1, pins 11 through 18 and pins 39 through 42 all are changed for output ports if they have been set for CD control signal input/output pins. 77 XVSS XVSS Input/Output CD's crystal oscillator power supply pins. Normally, connect these pins to the power supply lines that are used in common for the VDD and VSS pins. 78 79 XI XO XI XO Input/Output Input/Output CD's crystal oscillator input/output pins. Normally, connect 16.934MHz here. This clock is used as the system clock for the CD. After a system reset, it also is used as the system clock on the controller side. 80 XVDD XVDD Input/Output CD's crystal oscillator input/output pins. Normally, connect these pins to the power supply lines that are used in common for the VDD and VSS pins. 81 DVSR DVSR Input/Output R-channel D/A converter unit ground pin. 82 RO RO Input/Output R-channel data forward output pin. 83 DVRR DVRR Input/Output R-channel reference voltage pin. 84 DVDD DVDD Input/Output D/A converter unit power supply pin. 85 DVRL DVRL Input/Output L-channel reference voltage pin. 86 LO LO Input/Output L-channel data forward output pin. 87 DVSL DVSL Input/Output L-channel D/A converter unit ground pin. 88 89* NC NC/VPP NC NC Input/Output Input/Output NC pins. Normally, connect these pins to ground or leave them open. 90 /RST RESET Input Function Device's system reset signal input pin. The device remains reset while RESET is held low and when RESET is released back high, the CD unit becomes operational and the program starts from address 0. Normally, a system reset is asserted when a voltage of 2.7V or more is applied to VDD when it is at 0V (power-on reset). Therefore, this pin must be pulled high when used for this purpose. In this unit, the terminal with asterisk mark (*) is open terminal which is not connected to the outside. – 26 – GX-CD1200W IC802 VHiTC9457F0-1: Servo/Signal Control (TC9457F0) (4/4) Pin No. Port Name 91 /HOLD 92 Terminal Name Input/Output Function HOLD Input This pin is used to input a signal that requests or clears the hold mode. Normally, use this pin for CD mode select signal input or battery detection signal input. There are two hold modes: clock stop mode (crystal oscillator turned off) and a wait mode (CPU stopped). These modes are entered by executing the CKSTP and WAIT instructions, respectively. The clock stop mode can be requested by a programmed input: low level detection on HOLD pin or forced execution, and can be cleared by detecting a high on the HOLD pin or a change of state in its input signal. When the CKSTP instruction is executed, the clock generator and the CPU stop operating and the device is placed in a memory backup state. During this state, the device's current consumption is reduced to 1µA or less. At the same time, the display output and CMOS output ports are automatically set low, and the Nch open-drain outputs are turned off. The wait mode is executed regardles of the input state on the HOLD pin, with the device's current consumption reduced. This mode is cleared by a change of state in the HOLD input. INTR REMO-IN Input External interrupt input pin. When the interrupt facility is enabled and a pulse of 1.11 to 2.22µs in duration is applied to this pin, an interrupt is generated and the program jumps to address 1. Input logic and the active edge (rise or fall) can be selected for each interrupt input. Also, the internal 8-bit time clock can be chosen for this interrupt input, in which case it is possible to count pulses or generate an interrupt at a given pulse count (address 3). 93* 94* MXO MXI MXO MXI — — Crystal oscillator pins for the controller. The oscillator clock is used as the timebase for the clock facility or as the controller's system clock. Connect a 4.5MHz or 75kHz crystal resonator to the MXO and MXI pins. Since these pins do not contain internal feedback resistors, etc, an amp resistor or output resistor must be added external to the chip. When using the clock generated by the CD unit's crystal oscillator for clocking the entire device operation, fix the MXI pin to the GND level. Oscillation is stopped by executing a CKSTP instruction. Select the crystal oscillator and control its operation by a program. 95 96 MVSS MVDD MVSS MVDD — — Power supply pins. Normally, apply a voltage of 4.5 to 5.5V to VDD. In a backup state (when the CKSTP instruction executed), the device's current consumption is reduced to 1µA or less, allowing for the supply voltage to be lowered to 2.0V. The device is reset and the program starts from address 0 when a voltage of 2.7V or more is applied to this pin when it is at 0V (power-on reset). 97 98 99 100 OT1 OT2 OT3 OT4 COM1 COM2 COM3 COM4 Output Output Output Output Common signal outputs to the LCD panel. Up to 72 segments in a matrix with S1 to S18 can be displayed. Three voltage levels MVDD, VEE (1/2 MVDD), and GND are output for 83Hz period at 2ms intervals. After a system reset and after deassertion of a clock stop instruction, the VEE voltage is output and the DISP OFF bit is set to 0 before common signals are output. In this unit, the terminal with asterisk mark (*) is open terminal which is not connected to the outside. To serial No.006XXXXX From serial No.007XXXXX TC9457F-013 JAPAN TC7457F-022 JAPAN – 27 – GX-CD1200W —MEMO— – 28 – GX-CD1200W PARTS GUIDE PORTABLE CD STEREO COMPONENT SYSTEM GX-CD1200W(BK) MODEL GX-CD1200W(GL) “HOW TO ORDER REPLACEMENT PARTS” To have your order filled promptly and correctly, please furnish the following information. 1. MODEL NUMBER 2. REF. No. 3. PART NO. 4. DESCRIPTION For U.S.A. only Contact your nearest SHARP Parts Distributor to order. For location of SHARP Parts Distributor, Please call Toll-Free; 1-800-BE-SHARP MARK: SPARE PARTS-DELIVERY SECTION Explanation of capacitors/resistors parts codes Capacitors Resistors VCC ....................... Ceramic type VCK ........................ Ceramic type VCT ........................ Semiconductor type VC • • MF ............... Cylindrical type (without lead wire) VC • • MN ............... Cylindrical type (without lead wire) VC • • TV ................ Square type (without lead wire) VC • • TQ ............... Square type (without lead wire) VC • • CY ............... Square type (without lead wire) VC • • CZ ............... Square type (without lead wire) VC • • • • • • • • • J .. The 13th character represents capacity difference. ("J" ±5%, "K" ±10%, "M" ±20%, "N" ±30%, "C" ±0.25 pF, "D" ±0.5 pF, "Z" +80-20%.) VRD ....................... Carbon-film type VRS ........................ Carbon-film type VRN ....................... Metal-film type VR • • MF ............... Cylindrical type (without lead wire) VR • • MN ............... Cylindrical type (without lead wire) VR • • TV ................ Square type (without lead wire) VR • • TQ ............... Square type (without lead wire) VR • • CY ............... Square type (without lead wire) VR • • CZ ............... Square type (without lead wire) VR • • • • • • • • • J .. The 13th character represents error. ("J" ±5%, "F" ±1%, "D" ±0.5%.) If there are no indications for the electrolytic capacitors, error is ±20%. If there are no indications for other parts, the resistors are ±5% carbon-film type. NOTE: Parts marked with “ ” are important for maintaining the safety of the set. Be sure to replace parts with specified ones for maintaining the safety and performance of the set. – 29 – GX-CD1200W NO. PRICE RANK PARTS CODE DESCRIPTION INTEGRATED CIRCUITS IC1 IC2 IC101 IC151 IC201 IC202,203 IC401 IC402 IC501,502 IC801 IC802 IC803 VHITA7358AP-1 VHILA1805//-1 VHITA8189N/-1 VHITA2011S/-1 VHIBA3822LS-1 VHILB1403N/-1 VHIKIA4558P-1 VHILA4663//-1 VHIKA7809AP-1 VHITA2109F/-1 VHITC9457F0-1 VHILA6541D/-1 J J J J J J J J J J J J AG AM AM AM AL AG AC AQ FM Front End,TA7358AP FM/AM IF MPX.,LA1805 Record/Playback Amp.,TA8189N Mic Amp.,TA2011S Graphic Equalizer,BA3822LS Level Meter Driver,LB1403N Ope Amp.,KIA4558P Power Amp.,LA4663 Voltage Regulator,KA7809AP AL Servo Pre Amp.,TA2109F AZ Servo/Signal Control,TC9457F0 AW Focus/Tracking/Spin/Sled Driver, LA6541D ! J J J J J J J J J J J J J J J AB AC AB AB AC AB AB AC AB AC AC AF AB AC AC Silicon,NPN,KTC3199 GR Digital,PNP,KRA102 M Silicon,NPN,KTC3199 GR Silicon,NPN,KTC3199 GR Silicon,NPN,KTC3203 Y Silicon,NPN,KTC3199 GR Silicon,NPN,KTC3199 GR Silicon,PNP,KTA1271 Y Silicon,NPN,KTC3199 GR Digital,NPN,KRC102 M Digital,PNP,KRA102 M Silicon,NPN,KTD2058 Y Silicon,PNP,KTA1266 GR Silicon,PNP,KTA1271 Y Digital,NPN,KRC102 M VHDDS1SS133-1 VHDDS1SS133-1 VHDDS1SS133-1 VHDDS1SS133-1 VHDDS1SS133-1 VHDDS1SS133-1 VHDTS4B03GM-1 VHEDZ8R2BSB-1 VHP333ID213-1 VHP333ID213-1 VHP333ID213-1 VHP333ID213-1 J J J J J J J J J J J J AB AB AB AB AB AB AK AB Silicon,DS1SS133 Silicon,DS1SS133 Silicon,DS1SS133 Silicon,DS1SS133 Silicon,DS1SS133 Silicon,DS1SS133 Silicon,TS4B03GM Zener,8.2V,DZ8.2BSB LED,RED,333ID213 LED,RED,333ID213 LED,RED,333ID213 LED,RED,333ID213 RFILR0008AWZZ 92LFILTF1342A RFILA0001BGZZ J J J AE FM Band Pass Filter AD FM IF,10.7 MHz AC AM IF,455 kHz RTRNP0001BGZZ J AX Power RCILB0001BGZZ RCILR0001BGZZ RCILA0001BGZZ RCILA0003BGZZ RCILB0002BGZZ RCILB0003BGZZ RCILB0004BGZZ RCILI0002BGZZ RCILI0003BGZZ RCILI0001BGZZ VP-MK223K0000 RCILB0005BGZZ VP-MK470K0000 VP-DHR82K0000 VP-DH100K0000 J J J J J J J J J J J J J J J AD AA AH AC AC AC AC AD AD AD AC AD AB AE AB J J AC 10 kohm (B),Semi-VR [VCO] AC 470 ohms (B),Semi-VR [Tape Speed] FILTERS CF1 CF2 CF3 TRANSFORMER ! T601 COILS L1 L2 L3,4 L5 L6 L7 L8 L9 L10 L11 L103,104 L301 L501 L801 L802,803 FM Oscillation FM Tracking MW/SW1 Bar Antenna SW2 Antenna MW Oscillation SW1 Oscillation SW2 Oscillation FM IF FM Detection AM IF 22 mH,Choke Bias Oscillation 47 µH,Choke 0.82 µH,Choke 10 µH,Choke VARIABLE RESISTORS VR1 VR102 RVR-M0026AWZZ RVR-M0018AWZZ RVR-Q0002BGZZ RVR-Q0001BGZZ J J VR401 RVR-B0002BGZZ J DESCRIPTION AE 50 kohms (B)×2 [X-BASS] AC 100 kohm (B)×2 [Graphic Equalizer] 50 kohms (B)×2 [VOLUME] VARIABLE CAPACITORS TC5,6 TC7,8 TC9 VC1~4 RTO-H1003SJZZ RTO-H1001BGZZ RVC-Z0001BGZZ RVC-R0001BGZZ J J J J AG AD AF AK Trimmer,5 pF Trimmer,10 pF Fine Tuning Variable Capacitance with Trimmer (TC1~4) J AF Ceramic,16.93 MHz J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AA AA AA AB AA AA AA AA AA AA AA AA AB AA AA AA AA AB AA AB AB AA AB AA AB AA AB AC AA AB AA AA AA AA AA AB AB AB AB AB AA AA AB AB AB AB AA AA AB AA AB AB AB AB AB AB AB AB AB AA AB AB AB 5 pF (CH),50V 24 pF (CH),50V 0.001 µF,50V 0.0047 µF,50V 0.022 µF,50V 15 pF (CH),50V 22 pF (CH),50V 3 pF (CH),50V 0.022 µF,50V 5 pF (CH),50V 0.022 µF,50V 0.022 µF,50V 10 µF,16V,Electrolytic 330 pF,50V 0.0022 µF,50V 5 pF (UJ),50V 0.022 µF,50V 220 µF,10V,Electrolytic 0.022 µF,50V 0.0047 µF,50V 22 µF,16V,Electrolytic 0.022 µF,50V 0.0047 µF,50V,Mylar 0.0082 µF,50V,Mylar 3.3 µF,50V,Electrolytic 470 pF,50V 3.3 µF,50V,Electrolytic 0.0015 µF,100V 0.012 µF,50V,Mylar 1 µF,50V,Electrolytic 0.022 µF,50V 220 pF,50V 470 pF,50V 470 pF,50V 330 pF,50V 47 µF,10V,Electrolytic 0.015 µF,50V,Mylar 4.7 µF,50V,Electrolytic 10 µF,16V,Electrolytic 0.033 µF,50V,Mylar 330 pF,50V 0.01 µF,50V 4.7 µF,50V,Electrolytic 330 µF,10V,Electrolytic 2.2 µF,50V,Electrolytic 22 µF,16V,Electrolytic 120 pF,50V 150 pF,50V 0.0015 µF,50V,Mylar 0.33 µF,50V,Electrolytic 10 µF,16V,Electrolytic 47 µF,10V,Electrolytic 10 µF,16V,Electrolytic 100 µF,10V,Electrolytic 1 µF,50V,Electrolytic 47 µF,25V,Electrolytic 22 µF,16V,Electrolytic 100 µF,10V,Electrolytic 1 µF,50V,Electrolytic 220 pF,50V 1 µF,50V,Electrolytic 100 µF,10V,Electrolytic 4.7 µF,50V,Electrolytic VIBRATOR RCRM-0008AWZZ CAPACITORS VSKTC3199GR-1 VSKRA102M//-1 VSKTC3199GR-1 VSKTC3199GR-1 VSKTC3203Y/-1 VSKTC3199GR-1 VSKTC3199GR-1 VSKTA1271Y/-1 VSKTC3199GR-1 VSKRC102M//-1 VSKRA102M//-1 VSKTD2058Y/-1 VSKTA1266GR-1 VSKTA1271Y/-1 VSKRC102M//-1 DIODES D1,2 D152 D154 D156 D158 D162~165 D651 DZ601 LED1 LED253~260 LED401 LED501,502 PRICE RANK PARTS CODE VR202 VR203~205 XL801 TRANSISTORS Q153 Q154 Q156 Q181,182 Q301 Q403,404 Q502,503 Q504 Q505 Q601 Q602 Q603 Q801 Q802 Q803,804 NO. C2 C4 C5 C6,7 C8,9 C10 C11 C12 C13 C14 C15 C17 C18 C19 C20 C21 C22 C23 C24~26 C27 C29 C30 C31 C32 C33 C34 C35 C36 C37,38 C39~41 C42 C43 C101,102 C103,104 C105~108 C109,110 C111,112 C113~116 C117,118 C119,120 C121,122 C123,124 C125,126 C127 C128 C129 C131,132 C133,134 C137,138 C151 C152 C154 C155 C156 C157 C158,159 C160 C180 C181,182 C183,184 C185,186 C200 C201,202 –1– VCCCPU1HH5R0J VCCCPU1HH240J VCKYPA1HB102K VCKYPA1HB472K VCKZPA1HF223Z VCCCPU1HH150J VCCCPU1HH220J VCCCPU1HH3R0J VCKZPA1HF223Z VCCCPU1HH5R0J VCKZPA1HF223Z VCKZPA1HF223Z RC-GZA106AF1C VCKYPA1HB331K VCKYPA1HB222K VCCUPA1HJ5R0C VCKZPA1HF223Z RC-GZA227AF1A VCKZPA1HF223Z VCKYPA1HB472K RC-GZA226AF1C VCKZPA1HF223Z VCQYKA1HM472K VCQYKA1HM822K RC-GZA335AF1H VCKYPA1HB471K RC-GZA335AF1H 92LCPU100V1500 VCQYKA1HM123K RC-GZA105AF1H VCKZPA1HF223Z VCKYPA1HB221K VCKYPA1HB471K VCKYPA1HB471K VCKYPA1HB331K RC-GZA476AF1A VCQYKA1HM153K RC-GZA475AF1H RC-GZA106AF1C VCQYKA1HM333K VCKYPA1HB331K VCKYPA1HB103K RC-GZA475AF1H RC-GZA337AF1A RC-GZA225AF1H RC-GZA226AF1C VCKYPA1HB121K VCKYPA1HB151K VCQYKA1HM152K RC-GZA334AF1H RC-GZA106AF1C RC-GZA476AF1A RC-GZA106AF1C RC-GZA107AF1A RC-GZA105AF1H RC-GZA476AF1E RC-GZA226AF1C RC-GZA107AF1A RC-GZA105AF1H VCKYPA1HB221K RC-GZA105AF1H RC-GZA107AF1A RC-GZA475AF1H GX-CD1200W NO. PRICE RANK PARTS CODE C203,204 C205,206 C207,208 C209,210 C211,212 C213,214 C215,216 C217,218 C219,220 C221,222 C251,252 C253,254 C255,256 C257 C259,260 C301 C302 C303 C304 C305 C306 C307 C401,402 C403,404 C405,406 C407,408 C409,410 C411 C412 C413,414 C415,416 C418 C419,420 C423 C424 C425~428 C429,430 C433 C505 C506 C508 C509 C510 C511 C513,514 C601 C602 C603 C604 C651~654 C801 RC-GZA105AF1H VCQYKA1HM103K VCKYPA1HB471K VCQYKA1HM823K VCQYKA1HM152K RC-GZA334AF1H VCQYKA1HM562K RC-GZA474AF1H VCQYKA1HM393K RC-GZA475AF1H RC-GZA105AF1H VCKZPA1HF223Z RC-GZA106AF1C RC-GZA476AF1E VCQYKA1HM392K RC-GZA107AF1A VCQYKA1HM222K VCQYKA1HM562K VCKZPA1HF223Z VCQYKA1HM152K VCKYPA1HB391K VCKYPA1HB151K VCQYKA1HM682K RC-GZA106AF1C VCQYKA1HM332K RC-GZA475AF1H RC-GZA105AF1H RC-GZA476AF1A RC-GZA476AF1A VCQYKA1HM102K VCQYKA1HM154K RC-GZA226AF1C RC-GZA475AF1H RC-GZA106AF1C RC-GZA476AF1E VCQYKA1HM104K RC-GZA106AF1C VCKZPA1HF223Z RC-GZA476AF1C VCKZPA1HF223Z RC-GZA107AF1C VCKZPA1HF223Z RC-GZG338AF1E VCKZPA1HF223Z RC-GZA105AF1H VCKZPA1HF223Z RC-GZA107AF1A VCKZPA1HF223Z RC-GZA227AF1A VCKZPA1HF223Z VCQYKA1HM103K J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AB AA AA AC AB AA AA AA AB AB AB AA AB AB AA AB AA AA AA AB AA AA AA AB AA AB AB AB AB AA AB AB AB AB AB AB AB AA AB AA AB AA C802 C804 C805 C806 C807 C813 C814 C815 C816 C817 C818 C819,820 C821 C822 C823 C824 C825 C826 C827 C828 C829 C830 C832 C833 C834,835 C836~839 C840~842 C843 C844 C845 VCKZPA1HF223Z VCCCPA1HH2R0C VCKZPA1HF223Z RC-GZA227AF1A VCKZPA1HF473Z RC-GZA476AF1A VCKZPA1HF473Z RC-GZA476AF1A VCKZPA1HF223Z RC-GZA107AF1A VCCSPA1HL560J VCQYKA1HM104K RC-GZA476AF1A VCKZPA1HF473Z VCKZPA1HF223Z VCQYKA1HM104K RC-GZA476AF1A VCCSPA1HL470J VCQYKA1HM153K VCKYPA1HB272K VCKYPA1HB472K VCQYKA1HM103K RC-GZA476AF1A VCQYKA1HM333K VCKYPA1HB471K VCQYKA1HM473K VCKZPA1HF473K RC-GZA476AF1A RC-GZA107AF1A VCKZPA1HF473Z J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AA AA AA AB AA AB AA AB AA AB AA AB AB AA AA AB AB AA AB AA AB AA AB AB AA AB AA AB AB AA AA AB AA AB AA AB AA AA DESCRIPTION NO. 1 µF,50V,Electrolytic 0.01 µF,50V,Mylar 470 pF,50V 0.082 µF,50V,Mylar 0.0015 µF,50V,Mylar 0.33 µF,50V,Electrolytic 0.0056 µF,50V,Mylar 0.47 µF,50V,Electrolytic 0.039 µF,50V,Mylar 4.7 µF,50V,Electrolytic 1 µF,50V,Electrolytic 0.022 µF,50V 10 µF,16V,Electrolytic 47 µF,25V,Electrolytic 0.0039 µF,50V,Mylar 100 µF,10V,Electrolytic 0.0022 µF,50V,Mylar 0.0056 µF,50V,Mylar 0.022 µF,50V 0.0015 µF,50V,Mylar 390 pF,50V 150 pF,50V 0.0068 µF,50V,Mylar 10 µF,16V,Electrolytic 0.0033 µF,50V,Mylar 4.7 µF,50V,Electrolytic 1 µF,50V,Electrolytic 47 µF,10V,Electrolytic 47 µF,10V,Electrolytic 0.001 µF,50V,Mylar 0.15 µF,50V,Mylar 22 µF,16V,Electrolytic 4.7 µF,50V,Electrolytic 10 µF,16V,Electrolytic 47 µF,25V,Electrolytic 0.1 µF,50V,Mylar 10 µF,16V,Electrolytic 0.022 µF,50V 47 µF,16V,Electrolytic 0.022 µF,50V 100 µF,16V,Electrolytic 0.022 µF,50V 3300 µF,25V,Electrolytic 0.022 µF,50V 1 µF,50V,Electrolytic 0.022 µF,50V 100 µF,10V,Electrolytic 0.022 µF,50V 220 µF,10V,Electrolytic 0.022 µF,50V 0.01 µF,50V,Mylar [To Serial No.00404990 Only] 0.022 µF,50V 2 pF (CH),50V 0.022 µF,50V 220 µF,10V,Electrolytic 0.047 µF,50V 47 µF,10V,Electrolytic 0.047 µF,50V 47 µF,10V,Electrolytic 0.022 µF,50V 100 µF,10V,Electrolytic 56 pF,50V 0.1 µF,50V,Mylar 47 µF,10V,Electrolytic 0.047 µF,50V 0.022 µF,50V 0.1 µF,50V,Mylar 47 µF,10V,Electrolytic 47 pF,50V 0.015 µF,50V,Mylar 0.0027 µF,50V 0.0047 µF,50V 0.01 µF,50V,Mylar 47 µF,10V,Electrolytic 0.033 µF,50V,Mylar 470 pF,50V 0.047 µF,50V,Mylar 0.047 µF,50V 47 µF,10V,Electrolytic 100 µF,10V,Electrolytic 0.047 µF,50V –2– C846 C847 C848 C849,850 C851,852 C853 C854 C855 C858 C859 C860 C863 C893 C894 PRICE RANK PARTS CODE RC-GZA225AF1H RC-GZA226AF1C RC-GZA226AF1C VCKYPA1HB121K RC-GZA335AF1H VCKZPA1HF223Z VCKYPA1HB682K VCKZPA1HF223Z VCKZPA1HF223J VCKYPA1HB272K VCKYPA1HB152K RC-GZA476AF1A RC-GZA227AF1A VCKZPA1HF223Z DESCRIPTION J J J J J J J J J J J J J J AB AB AB AA AB AA AB AA AA AA AB AB AA 2.2 µF,50V,Electrolytic 22 µF,16V,Electrolytic 22 µF,16V,Electrolytic 120 pF,50V 3.3 µF,50V,Electrolytic 0.022 µF,50V 0.0068 µF,50V 0.022 µF,50V 0.022 µF,50V 0.0027 µF,50V 0.0015 µF,50V 47 µF,10V,Electrolytic 220 µF,10V,Electrolytic 0.022 µF,50V J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA 10 ohm,1/4W 33 ohms,1/6W 47 ohms,1/6W 330 kohms,1/6W 100 ohm,1/6W 820 kohms,1/6W 3.9 kohms,1/6W 12 kohms,1/6W 47 ohms,1/4W 1 kohm,1/6W 100 ohm,1/4W 100 kohm,1/6W 10 kohm,1/6W 2.7 kohms,1/6W 15 kohms,1/6W 10 ohm,1/4W 150 ohms,1/4W 100 ohm,1/6W 180 kohms,1/6W 10 kohm,1/6W 6.8 kohms,1/6W 22 kohms,1/6W 120 kohms,1/6W 680 ohms,1/6W 330 kohms,1/6W 100 ohm,1/6W 10 kohm,1/6W 22 kohms,1/6W 150 kohms,1/6W 1.2 kohms,1/6W 82 kohms,1/6W 10 kohm,1/6W 2.2 kohms,1/6W 4.7 kohms,1/6W 2.2 kohms,1/6W 560 ohms,1/6W 1 Mohm,1/6W 10 kohm,1/6W 560 ohms,1/4W 10 kohm,1/6W 33 kohms,1/6W 10 kohm,1/6W 22 kohms,1/6W 1 kohm,1/6W 560 ohms,1/4W 1 kohm,1/6W 330 kohms,1/6W 220 ohms,1/6W 3.9 kohms,1/6W 330 ohms,1/4W 1 kohm,1/6W 2.2 kohms,1/6W 4.7 kohms,1/6W 3.3 kohms,1/6W 4.7 kohms,1/6W 3.3 kohms,1/6W 1 kohm,1/6W 6.8 kohms,1/6W 39 kohms,1/6W 120 ohms,1/4W 10 kohm,1/6W 120 ohms,1/4W 330 ohms,1/4W 100 ohm,1/4W 10 ohm,1/4W RESISTORS R1 R2 R3 R4 R5 R7 R8 R9 R10,11 R12 R13 R14 R15,16 R17,18 R19 R20 R100 R101,102 R105,106 R107,108 R109,110 R111,112 R113,114 R115,116 R117,118 R119,120 R121~124 R127,128 R129,130 R131,132 R133,134 R135,136 R151 R152 R153 R154 R161 R165 R166 R168,169 R170,171 R172,173 R174 R177 R180 R181,182 R183,184 R185,186 R187,188 R200 R201,202 R203,204 R205 R206 R207 R208 R211,212 R251,252 R253,254 R255,256 R257,258 R259,260 R301 R302,303 R304 VRD-ST2EE100J VRD-ST2CD330J VRD-ST2CD470J VRD-ST2CD334J VRD-ST2CD101J VRD-ST2CD824J VRD-ST2CD392J VRD-ST2CD123J VRD-ST2EE470J VRD-ST2CD102J VRD-ST2EE101J VRD-ST2CD104J VRD-ST2CD103J VRD-ST2CD272J VRD-ST2CD153J VRD-ST2EE100J VRD-ST2EE151J VRD-ST2CD101J VRD-ST2CD184J VRD-ST2CD103J VRD-ST2CD682J VRD-ST2CD223J VRD-ST2CD124J VRD-ST2CD681J VRD-ST2CD334J VRD-ST2CD101J VRD-ST2CD103J VRD-ST2CD223J VRD-ST2CD154J VRD-ST2CD122J VRD-ST2CD823J VRD-ST2CD103J VRD-ST2CD222J VRD-ST2CD472J VRD-ST2CD222J VRD-ST2CD561J VRD-ST2CD105J VRD-ST2CD103J VRD-ST2EE561J VRD-ST2CD103J VRD-ST2CD333J VRD-ST2CD103J VRD-ST2CD223J VRD-ST2CD102J VRD-ST2EE561J VRD-ST2CD102J VRD-ST2CD334J VRD-ST2CD221J VRD-ST2CD392J VRD-ST2EE331J VRD-ST2CD102J VRD-ST2CD222J VRD-ST2CD472J VRD-ST2CD332J VRD-ST2CD472J VRD-ST2CD332J VRD-ST2CD102J VRD-ST2CD682J VRD-ST2CD393J VRD-ST2EE121J VRD-ST2CD103J VRD-ST2EE121J VRD-ST2EE331J VRD-ST2EE101J VRD-ST2EE100J GX-CD1200W NO. PRICE RANK PARTS CODE R305 R306 R351,352 R353,354 R401,402 R403,404 R405,406 R407~410 R411 R412,413 R415,416 R417,418 R419,420 R425,426 R427,428 R429 R431 R433~436 R437,438 R440 R441,442 R511~513 R514 R515 R516 R518,519 R520,521 R601 R602 R801 R802 VRD-ST2EE273J VRD-ST2EE470J VRD-ST2CD473J VRD-ST2CD273J VRD-ST2CD104J VRD-ST2CD103J VRD-ST2CD272J VRD-ST2CD123J VRD-ST2EE331J VRD-ST2CD103J VRD-ST2CD332J VRD-ST2CD223J VRD-ST2CD332J VRD-ST2CD102J VRD-ST2CD472J VRD-ST2CD104J VRD-ST2CD273J VRD-ST2CD2R2J VRD-ST2EE121J VRD-ST2EE471J VRD-ST2CD153J VRD-ST2CD103J VRD-ST2CD104J VRD-ST2CD121J VRD-ST2CD302J VRD-ST2CD102J VRD-ST2CD103J VRD-ST2EE271J VRD-ST2EE101J VRD-ST2EE220J VRD-ST2CD222J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA R803 R804 R805 R806 R807 R811 R812 R820 R821,822 R824 R826 R827 R828 R829 R830 R831~834 R835,836 R839 R840 R844 R846 R847 R848 R849 R851~853 R857,858 R861 R863 R865 R891 VRD-ST2CD823J VRD-ST2CD683J VRD-ST2CD393J VRD-ST2CD272J VRD-ST2CD102J VRD-ST2CD223J VRD-ST2CD102J VRD-ST2CD473J VRD-ST2CD223J VRD-ST2CD103J VRD-ST2CD224J VRD-ST2CD153J VRD-ST2CD103J VRD-ST2CD332J VRD-ST2CD103J VRD-ST2CD332J VRD-ST2CD153J VRD-ST2CD473J VRD-ST2EE100J VRD-ST2CD332J VRD-ST2CD331J VRD-ST2CD102J VRD-ST2CD222J VRD-ST2CD682J VRD-ST2CD222J VRD-ST2CD562J VRD-ST2CD332J VRD-ST2CD332J VRD-ST2CD102J VRD-ST2CD683J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA R892 VRD-ST2CD563J J AA R893~895 VRD-ST2CD683J J AA R896 VRD-ST2CD563J J AA NO. 27 kohms,1/4W 47 ohms,1/4W 47 kohms,1/6W 27 kohms,1/6W 100 kohm,1/6W 10 kohm,1/6W 2.7 kohms,1/6W 12 kohms,1/6W 330 ohms,1/4W 10 kohm,1/6W 3.3 kohms,1/6W 22 kohms,1/6W 3.3 kohms,1/6W 1 kohm,1/6W 4.7 kohms,1/6W 100 kohm,1/6W 27 kohms,1/6W 2.2 ohms,1/6W 120 ohms,1/4W 470 ohms,1/4W 15 kohms,1/6W 10 kohm,1/6W 100 kohm,1/6W 120 ohms,1/6W 3.6 kohms,1/6W 1 kohm,1/6W 10 kohm,1/6W 270 ohms,1/4W 100 ohm,1/4W 22 ohms,1/4W 2.2 kohms,1/6W [To Serial No.00404990 Only] 82 kohms,1/6W 68 kohms,1/6W 39 kohms,1/6W 2.7 kohms,1/6W 1 kohm,1/6W 22 kohms,1/6W 1 kohm,1/6W 47 kohms,1/6W 22 kohms,1/6W 10 kohm,1/6W 220 kohms,1/6W 15 kohms,1/6W 10 kohm,1/6W 3.3 kohms,1/6W 10 kohm,1/6W 3.3 kohms,1/6W 15 kohms,1/6W 47 kohms,1/6W 10 ohm,1/4W 3.3 kohms,1/6W 330 ohms,1/6W 1 kohm,1/6W 2.2 kohms,1/6W 6.8 kohms,1/6W 2.2 kohms,1/6W 5.6 kohms,1/6W 3.3 kohms,1/6W 3.3 kohms,1/6W 1 kohm,1/6W 68 kohms,1/6W [From Serial No.00504991] 56 kohms,1/6W [From Serial No.00504991] 68 kohms,1/6W [From Serial No.00504991] 56 kohms,1/6W [From Serial No.00504991] CNP501 CNP601 CNP803 CNP804 CNS101 CNS102 CNS103 CNS601 F601 FW1 FW2 FW801 FW802 J151 J401 LCD801 M501(300-10) M801 M802 MIC151 SO601 SP401,402 SP403,404 SW1 QTANA0001BGZZ QCNCM035BAWZZ 92LCONE6P53254 QCNCM705FAFZZ QCNWN0001BGZZ QCNWN0002BGZZ QCNWN0003BGZZ QCNWN0006BGZZ QFS-D402ABGNI QCNWN0038BGZZ QCNWN0014BGZZ QCNWN0030AFZZ QCNWN0029AFZZ QJAKA0004BGZZ QJAKM0001BGZZ RV-LX0001BGZZ 92L1959123012 92LMMTR1651B 92LMMTR1854A RMICC0001BGZZ QSOCA0006SJZZ VSP0012PBG28A RALMB0001BGZZ QSW-S9001BGZZ J J J J J J J J J J J J J J J J J J J J J J J J SW101 QSW-S9002BGZZ J AD SW102 SW103 QSW-S9003BGZZ QSW-S9004BGZZ J J AC AC SW401 SW501 QSW-P9001BGZZ QSW-S9005BGZZ J J AE AD SW601 QSW-S0004SJZZ J AK SW702 SW801 SW801 SW802 SW803 SW804 QSWF9001AW01 QSW-K0008AWZZ 92LSWICHT1663 QSW-K0008AWZZ QSW-K0008AWZZ QSW-K0008AWZZ J J J J J J AC AC AC AC AC SW810 QSW-P0004AWZZ SW901(300-12) 92L640101149 SW902(300-11) 92L640101149 SW903(300-13) 92L640101149 SW904(300-14) 92L64030204 J J J J J AE OTHER CIRCUITRY PARTS BI801/CNS801 QCNWN0026BGZZ J BI802/CNS802 QCNWN0027BGZZ J BI802/CNS802 QCNWN0032BGZZ J BI803/CNS803 BI804/CNS804 CNP101 CNP102 CNP103 QCNWN0028BGZZ QCNWN0031BGZZ QCNCM705CAFZZ QCNCM705DAFZZ QCNCM698JAFZZ J J J J J PRICE RANK DESCRIPTION Connector Ass’y,8/8Pin Connector Ass’y,5/5Pin [To Serial No.00404990] Connector Ass’y,7/7Pin [From Serial No.00504991] Connector Ass’y,6/6Pin Connector Ass’y,6/6Pin AA Plug,3Pin AB Plug,4Pin AC Plug,9Pin ! ! ! PARTS CODE AD AB AC AB AD AE AF AD AC AA AG AE AL AP AF AB AC AE DESCRIPTION Terminal,Speaker Plug,2Pin Plug,6Pin Plug,6Pin Connector Ass’y,3Pin Connector Ass’y,4Pin Connector Ass’y,9Pin Connector Ass’y,2Pin T4A L 250V Flat Wire,4Pin Flat Wire,2Pin Flat Wire,10Pin Flat Wire,2Pin Jack,Mic Jack,Headphones LCD Display Motor with Pulley [Tape] Motor with Chassis [Sled] Motor with Gear [Spindle] Built-in Microphone AC Socket Speaker,Woofer Speaker,Tweeter Switch,Slide Type [Band Selector] Switch,Slide Type [Record/Playback] Switch,Slide Type [Beat Cancel] Switch,Slide Type [Dubbing Speed/Mic/FM Mode] Switch,Push Type [Surround] Switch,Slide Type [Function Selector] Switch,Slide Type [Voltage Selector] Switch,Push Type [Pickup In] Switch,Key Type [Play/Pause] Switch,Key Type [Play/Pause] Switch,Key Type [Stop] Switch,Key Type [Cue/Track Up] Switch,Key Type [Review/Track Down] Switch,Push Type [Open/Close] Switch,Leaf Type [Tape 1 Main] Switch,Leaf Type [Tape 2 Main] Switch,Leaf Type [Tape 2 Play] Switch,Slide Type [Tape 2 Direction] CD MECHANISM PARTS NGERH0011AWZZ NGERH0012AWZZ MLEVP0080AWZZ NSFTM0020AWFW 92LMCUSN1524A 92LHPC1LASY J J J J J J AC AC AC AD AD ! 301 302 303 304 305 306 ! 306 92LHPC1LXASY J BD 307 701 702 703 704 M801 M802 SW702 PCOVP1001AWSA XBSSD26P06000 XHBSD20P05000 XBBSD20P03000 LX-WZ1070AFZZ 92LMMTR1651B 92LMMTR1854A QSWF9001AW01 J J J J J J J J AE AA AA AA AA AL AP Gear,Middle Gear,Drive Rail,Guide Shaft,Guide Cushion Pickup Unit Ass’y [To Serial No.00404990] Pickup Unit Ass’y [From Serial No.00504991] Cover,CD Mechanism Screw,ø2.6×6mm Screw,ø2×5mm Screw,ø2×3mm Washer,ø1.5×ø3.8×0.25mm Motor with Chassis [Sled] Motor with Gear [Spindle] Switch,Push Type [Pickup In] CABINET PARTS 201 201 202 202 203 203 204 205 206 207 208 –3– GCABA1003BGSA GCABA1003BGSB GFTAC0001BGSB GFTAC0001BGSC GFTAC0002BGSB GFTAC0002BGSC HBDGA1003BGSA HBDGS1001BGSA HDECQ0001BGSA HDECQ0004BGSA HDECQ0017BGSA J J J J J J J J J J J AK AK AF AH AD Front Cabinet [GL] Front Cabinet [BK] Cassette Holder [Tape 1] [BK] Cassette Holder [Tape 1] [GL] Cassette Holder [Tape 2] [BK] Cassette Holder [Tape 2] [GL] Badge,SHARP Sheet,Surround Sound System Panel,Display Ring,Volume Knob Panel,Cassette Holder [Tape 1] GX-CD1200W NO. PRICE RANK PARTS CODE 209 210 211 212 213 214 215 216 218 219 220 221 222 222 223 223 224 224 225 HDECQ0008BGSA HDECZ0001BGSA HSSND0001BGSA JKNBQ0001BGSC LANGT0001BGFW MLIFP0001BGZZ MSPRD0001BGFW NGERH0002BGZZ LANGG0001BGFW HDECQ0005BGSA JKNBK0001BGSB LHLDW1033CE00 JBTN-0001BGSB JBTN-0001BGSC JBTN-0002BGSB JBTN-0002BGSC JBTN-0003BGSB JBTN-0003BGSC JBTN-0004BGSB J J J J J J J J J J J J J J J J J J J 225 JBTN-0004BGSC J 226 226 227 227 228 JBTN-0005BGSB JBTN-0005BGSC JBTN-0006BGSB JBTN-0006BGSC JBTN-0007BGSB J J J J J 228 JBTN-0007BGSC J 229 229 230 230 231 JBTN-0008BGSB JBTN-0008BGSC JBTN-0009BGSB JBTN-0009BGSC JBTN-0010BGSB J J J J J 231 JBTN-0010BGSC J 232 232 233 233 234 235 236 237 238 239 240 241 242 243 244 245 245 246 247 247 248 JBTN-0011BGSB JBTN-0011BGSC JBTN-0012BGSB JBTN-0012BGSC LANGF0001BGZW LHLDZ8001BG00 LHLDZ1002BGZZ MSPRC0001BGFJ PRDAR0001BGFW NGERK0001BGZZ PSHEP0001BGSA PSHEP0002BGSA JKNBZ0001BGSA PCOVZ9001BGZZ MSPRP0001BGFW GCABB1003BGSA GCABB1003BGSB GLEGG0001BG00 JHNDP1002BGSA JHNDP1002BGSB LHLDQ1001BGZZ J J J J J J J J J J J J J J J J J J J J J 249 250 251 253 254 255 256 257 258 259 260 261 262 263 263 264 MSPRB0002BGFW MSPRC0002BGFJ MSPRC0003BGFJ QANTR0002BGZZ LHLDR1001BGZZ NGERK0002BGZZ NGERK0003BGZZ JKNBM0001BGSA JKNBP0001BGSA JKNBP0001BGSA JKNBP0002BGSA LHLDS1002BGZZ MLEVP0002BGZZ GFTAB1001BGSB GFTAB1001BGSC TSPC-0017BGZZ J J J J J J J J J J J J J J J J 264 TSPC-0018BGZZ J 264 TSPC-0020BGZZ J DESCRIPTION NO. AD Panel,Cassette Holder [Tape 2] AC Panel,Dial Pointer AC Dial Pointer Knob,Tuning AD Bracket,Front Cabinet AD Gear,Cassette Holder AB Spring,Cassette Holder Up AC Gear,Tuning Knob AB Guide,Dial Pointer AC Cap,Volume Knob Knob,Volume Nylon Band AC Button,Record [Tape 1] [BK] Button,Record [Tape 1] [GL] AC Button,Play [Tape 1] [BK] Button,Play [Tape 1] [GL] AC Button,Rewind [Tape 1] [BK] Button,Rewind [Tape 1] [GL] AC Button,Fast Forward [Tape 1] [BK] Button,Fast Forward [Tape 1] [GL] AC Button,Stop/Eject [Tape 1] [BK] Button,Stop/Eject [Tape 1] [GL] AC Button,Pause [Tape 1] [BK] Button,Pause [Tape 1] [GL] AC Button,Reverse Mode [Tape 2] [BK] Button,Reverse Mode [Tape 2] [GL] AC Button,Play [Tape 2] [BK] Button,Play [Tape 2] [GL] AC Button,Rewind [Tape 2] [BK] Button,Rewind [Tape 2] [GL] AC Button,Fast Forward [Tape 2] [BK] Button,Fast Forward [Tape 2] [GL] AC Button,Stop/Eject [Tape 2] [BK] Button,Stop/Eject [Tape 2] [GL] AC Button,Direction [Tape 2] [BK] Button,Direction [Tape 2] [GL] Support,Mechanism Button Shaft AC Holder,Mic AC Holder,LED A AC Spring,Battery,AL Heat Sink,Main AD Dial Drum AD Sheet,LED,Left AD Sheet,LED,Right AC Knob,Fine Tuning AB Cover,Dial Pointer AC Plate,Record Rear Cabinet [GL] Rear Cabinet [BK] AB Cushion,Leg Handle [GL] Handle [BK] AE Holder,AC Socket/Voltage Selector AB Spring,Rod Antenna AC Spring,Battery,+/AC Spring,Battery,+/AK Rod Antenna AD Holder,Tuning AB Gear,Tuning A AB Gear,Tuning B AD Button,Surround AA Knob,Function AA Knob,Dubbing Speed AB Knob,Band Selector AC Holder,Record Lever AB Lever,Record AE Battery Compartment Lid [BK] Battery Compartment Lid [GL] Label,Specifications [GL] [For Malaysia/Asia Middle East/ Africa] Label,Specifications [GL] [For Jordan/Egypt] Label,Specifications [GL] [For Thailand] –4– ! ! PRICE RANK PARTS CODE 264 TSPC-0026BGZZ J 264 TSPC-0027BGZZ J 264 TSPC-0028BGZZ J 264 TSPC-0029BGZZ J 264 TSPC-0030BGZZ J 266 267 267 268 268 269 270 271 271 272 273 274 275 276 277 278 279 280 300 300- 1 300- 2 300- 3 PRDAR0002BGFW GCABC1003BGSA GCABC1003BGSB GFTAT1001BGSA GFTAT1001BGSB HPNLZ1001BGSA HPNLZ1002BGSA JBTN-0024BGSA JBTN-0024BGSB MLEVP0003BGZZ JKNBK0002BGSA LHLDM1001BGZZ PMAGF0001BGZZ LHLDZ1003BGZZ MSPRD0002BGFJ QFSHD0017CEZZ QFSHD0018CEZZ MSPRB0003BGFW CMECB0001BG01 92L192104309 92L195904302 92L195904301 J J J J J J J J J J J J J J J J J J J J J J 300- 4 92L6201-01-111 300- 5 92L6209-10-10 300- 6 92L6216-07-01 300- 7 92L19210703 300- 8 92L182112173 300- 9 92L182112142 300-10(M501) 92L1959123012 300-11(SW902) 92L640101149 300-12(SW901) 92L640101149 300-13(SW903) 92L640101149 300-14(SW904) 92L64030204 J J J J J J J J J J J 601 602 603 604 605 606 607 608 609 610 611 612 613 J J J J J J J J J J J J J XEBSD30P10000 XJBSD30P08000 XBPSD26P04JS0 XHBSD20P04000 XJSSD30P10000 XBBSF30P10000 XJBSD40P16000 XEBSD30P20000 XHSSF30P06000 XEBSD30P10000 LX-JZ0002AWFD XESSD30P10000 LX-EZ0005AWFD BL AA AA AA AA AA AB AA AA AA AA AA DESCRIPTION Label,Specifications [BK] [For Malaysia/Asia Middle East/ Africa] Label,Specifications [BK] [For Jordan/Egypt] Label,Specifications [BK] [For Thailand] Label,Specifications [GL] [For Australia] Label,Specifications [BK] [For Australia] Heat Sink,Sub Top Cabinet [GL] Top Cabinet [BK] CD Lid [GL] CD Lid [BK] Panel,Decoration Panel,LCD Button,CD Lid Open [GL] Button,CD Lid Open [BK] Lock Lever,CD Lid Button,Function Stabilizer Magnet Holder,LCD Spring,CD Lid Holder,Fuse Holder,Fuse Spring,CD LID Open Button Tape Mechanism Ass’y Pinch Roller Arm Ass’y Pinch Roller Arm Ass’y,Rewind Pinch Roller Arm Ass’y,Fast Forward Head,Record/Playback,Tape 1 Head,Erase,Tape 1 Head,Playback,Tape 2 FF/REW Belt Main Belt,Tape 1 Main Belt,Tape 2 Motor with Pulley [Tape] Switch,Leaf Type [Tape 2 Main] Switch,Leaf Type [Tape 1 Main] Switch,Leaf Type [Tape 2 Play] Switch,Slide Type [Tape 2 Direction] Screw,ø3×10mm Screw,ø3×8mm Screw,ø2.6×4mm Screw,ø2×4mm Screw,ø3×10mm Screw,ø3×10mm Screw,ø4×16mm Screw,ø3×20mm Screw,ø3×6mm Screw,ø3×10mm Screw,ø3×10mm Screw,ø3×10mm Screw,ø2.6×10mm SPEAKER BOX PARTS 301 301 302 302 303 303 304 304 305 306 306 307 308 309 701 702 SP401,402 SP403,404 CCAB-120LBG01G CCAB-120LBG01K CCAB-120RBG01G CCAB-120RBG01K GCABD1001BGSB GCABD1001BGSC GCABF1001BGSB GCABF1001BGSC GLEGG0001BG00 LHLDW1001BGSB LHLDW1001BGSC QCNWG0001BGZZ LPLTW0001BGZZ LPLTW0002BGZZ XEBSD30P10000 XJBSD40P16000 VSP0012PBG28A RALMB0001BGZZ J J J J J J J J J J J J J J J J J J AQ AQ AB AB AE AC AC AA AB AC Front Panel,Ass’y,Left [GL] Front Panel,Ass’y,Left [BK] Front Panel,Ass’y,Right [GL] Front Panel,Ass’y,Right [BK] Speaker Box,Left [BK] Speaker Box,Left [GL] Speaker Box,Right [BK] Speaker Box,Right [GL] Cushion,Leg,Speaker Holder,Speaker Cord [BK] Holder,Speaker Cord [GL] Cord,Speaker Support H,Speaker Box Support V,Speaker Box Screw,ø3×10mm Screw,ø4×16mm Speaker,Woofer Speaker,Tweeter GX-CD1200W NO. PRICE RANK PARTS CODE DESCRIPTION NO. ACCESSORIES/PACKING PARTS ! ! ! ! ! QACCA0001SJ00 QACCE0007AW00 QACCL0002AW00 QPLGA0250AFZZ QPLGA0253AFZZ SPAKA0003BGZZ SPAKC0023BGZZ J J J J J J J AS AH AN AF AE SPAKC0024BGZZ J SPAKC0033BGZZ J SPAKC0034BGZZ J SSAKA0002BGZZ J AB SSAKH0002BGZZ SSAKH0004BGZZ SSAKH0005BGZZ TGANE0002BG03 TGANE0003BGZZ TINSZ0008BGZZ TLABB0001BGZZ TLABB0002BGZZ TLABE0005BGZZ TLABE0008BGZZ TLABR1137BGZZ TLABR1138BGZZ TLABS0002BGZZ TLABS0003BGZZ TLABZ0001BGZZ TLABZ0002BGZZ TLABZ0009BGZZ TLABZ0010BGZZ J J J J J J J J J J J J J J J J J J AB AB AB TLABZ0011BGZZ J TLABZ0012BGZZ J AB AC AC Power Supply Cord AC Power Supply Cord AC Power Supply Cord Adaptor,AC Plug Adaptor,AC Plug Packing Add.,Unit Packing Case [GL] [For Malaysia] Packing Case [GL] [Except for Malaysia] Packing Case [BK] [For Malaysia] Packing Case [BK] [Except for Malaysia] Polyethylene Bag,AC Plug Adaptor Polyethylene Bag,Accessories Polyethylene Bag,Unit Polyethylene Bag,Speaker Warranty Card [For Philippines] Warranty Card [For Australia] Operation Manual Label,Japan Label,Japan Label,Ean Bar Code [GL] Label,Ean Bar Code [BK] Label,Bar Code [GL] Label,Bar Code [BK] Label,Laser Label,Class 3 Label,Contru origin for Set Label,Contru origin for P-case Label,Feature,Left [For Malaysia] Label,Feature,Right [For Malaysia] Label,Feature,Left [Except for Malaysia] Label,Feature,Right [Except for Malaysia] P.W.B. ASSEMBLY (Not Replacement Item) PWB-A1~8 DUNTK0003BG01 J PWB-B PWB-C1~3 QPWBF0027AWZZ J DUNTK0004BG01 J — Main/Graphic Equalizer/Volume/ Fine Tuning/Terminal A/ Terminal B/Power/Holder (Combined Ass’y) AD CD Motor (PWB Only) — CD Servo/CD Control/Switch (Combined Ass’y) OTHER SERVICE PART UDSKA0004AFZZ J AZ Pickup Lens Cleaner –5– PARTS CODE PRICE RANK DESCRIPTION GX-CD1200W 307 A 306 B 701 304 701 704 C 302 702 301 D 303 703x2 E M802 F 305 M801 305x2 G SW702 PWB-B H 1 2 3 4 Figure 6 CD MECHANISM EXPLODED VIEW –6– 5 6 GX-CD1200W 269 247 271 CD MECHANISM A 610x2 268 278 277 263 275 267 274 608x3 253 245 PWB-C2 613x3 B 264 273 612x3 276 LCD801 601x3 606 PWB-C3 272 214 607 SW601 PWB-C1 609 248 601x3 C SO601 250 607x3 T601 PWB-A6 607x2 246 246x2 251 249 609 279 280 601x2 D 237 PWB-A7 246 PWB-A5 601 603 601x2 236 213 605x5 270 255 239 256 Silicon Grease 254 MIC151 240 602 601x2 211 266 601 235 PWB-A8 218 204 E 601 PWB-A2 241 201 251 611 601 Silicon Grease 258 238 VR401 PWB-A3 PWB-A1 601 259 260 243 IC502 602x2 257 205 601x2 IC402 Q601 214x2 F 602x2 261 601 605x6 244 213 242 216 222 223 224 PWB-A4 225 226 227 202 228 229 203 230 231 232 210 206 With VR401 234x2 233 207 300(300-1, 300-2, 300-3, 300-4, 300-5, 300-6, 300-7, 300-8,300-9,300-10(M501), 300-11(SW902), 300-12(SW901), 300-13(SW903), 300-14(SW904) 220 219 208 215 221 215 604 TAPE MECHANISM 601 212 G 262 209 H Note: Only the unit and consumale parts are supplied as parts supply for the Tape mechanism. 1 2 3 4 Figure 7 CABINET EXPLODED VIEW –7– 5 6 GX-CD1200W A 702x5 303(LEFT) 304(RIGHT) 301(LEFT) 302(RIGHT) SP403(L-CH) SP404(R-CH) 307 B 701x4 306 C 308 D SP401(L-CH) SP402(R-CH) 305 305 309 305 305 TWEETER SP403(L-CH) SP404(R-CH) E BLACK RED BLACK F TWEETER SP403(L-CH) SP404(R-CH) G WOOFER SP401(L-CH) SP402(R-CH) RED WOOFER SP401(L-CH) SP402(R-CH) H 1 2 3 4 Figure 8 SPEAKER EXPLODED VIEW –8– 5 6 GX-CD1200W —MEMO— –9– GX-CD1200W —MEMO— – 10 GX-CD1200W COPYRIGHT © 2000 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any from or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. SHARP CORPORATION Communication Systems Group Quality & Reliability Control Center Higashihiroshima, Hiroshima 739-0192, Japan Printed in Japan A0006-1408DS•HA•I SCA • SCNZ • EX