Download Siemens Model 240 Technical data

Parameters
Connector/Binector (BICO)-Parameters
1.4.2
p20163
BI: PDE 1 input pulse I / PDE 1 inp_pulse I
p20168
BI: PDF 0 input pulse I / PDF 0 inp_pulse I
p20173
BI: PDF 1 input pulse I / PDF 1 inp_pulse I
p20178[0...1]
BI: PST 0 inputs / PST 0 inputs
p20183[0...1]
BI: PST 1 inputs / PST 1 inputs
p20188[0...1]
BI: RSR 0 inputs / RSR 0 inputs
p20193[0...1]
BI: RSR 1 inputs / RSR 1 inputs
p20198[0...3]
BI: DFR 0 inputs / DFR 0 inputs
p20203[0...3]
BI: DFR 1 inputs / DFR 1 inputs
p20208[0...1]
BI: BSW 0 inputs / BSW 0 inputs
p20209
BI: BSW 0 switch setting I / BSW 0 sw_setting
p20213[0...1]
BI: BSW 1 inputs / BSW 1 inputs
p20214
BI: BSW 1 switch setting I / BSW 1 sw_setting
p20219
BI: NSW 0 switch setting I / NSW 0 sw_setting
p20224
BI: NSW 1 switch setting I / NSW 1 sw_setting
p20245
BI: PT1 0 accept setting value S / PT1 0 acc set val
p20251
BI: PT1 1 accept setting value S / PT1 1 acc set val
p20260
BI: INT 0 accept setting value S / INT 0 acc set val
p20300
BI: NOT 4 input I / NOT 4 input I
p20304
BI: NOT 5 input I / NOT 5 input I
p20324[0...1]
BI: RSR 2 inputs / RSR 2 inputs
p20329[0...3]
BI: DFR 2 inputs / DFR 2 inputs
p20334
BI: PDE 2 input pulse I / PDE 2 inp_pulse I
p20339
BI: PDE 3 input pulse I / PDE 3 inp_pulse I
p20344
BI: PDF 2 input pulse I / PDF 2 inp_pulse I
p20349
BI: PDF 3 input pulse I / PDF 3 inp_pulse I
p20354
BI: MFP 2 input pulse I / MFP 2 inp_pulse I
p20359
BI: MFP 3 input pulse I / MFP 3 inp_pulse I
Connector Input Parameters
Product: SINAMICS G120 CU240, Version: 4402100, Language: eng, Type: CI
p0641[0...n]
1-476
CI: Current limit, variable / Curr lim var
p0771[0...1]
CI: CU analog outputs signal source / CU AO S_src
p1042[0...n]
CI: Motorized potentiometer automatic setpoint / Mop auto setpoint
p1044[0...n]
CI: Motorized potentiometer setting value / Mop set val
p1051[0...n]
CI: Speed limit RFG positive direction of rotation / n_limit RFG pos
p1052[0...n]
CI: Speed limit RFG negative direction of rotation / n_limit RFG neg
p1070[0...n]
CI: Main setpoint / Main setpoint
p1071[0...n]
CI: Main setpoint scaling / Main setp scal
p1075[0...n]
CI: Suppl setpoint / Suppl setpoint
p1076[0...n]
CI: Supplementary setpoint scaling / Suppl setp scal
p1085[0...n]
CI: Speed limit in positive direction of rotation / n_limit pos
p1088[0...n]
CI: Speed limit in negative direction of rotation / n_limit neg
p1109[0...n]
CI: Total setpoint / Total setp
p1144[0...n]
CI: Ramp-function generator setting value / RFG setting value
p1155[0...n]
CI: Speed controller speed setpoint 1 / n_ctrl n_set 1
p1160[0...n]
CI: Speed controller speed setpoint 2 / n_ctrl n_set 2
p1330[0...n]
CI: U/f control independent voltage setpoint / Uf U_set independ.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011