Download Roper 8575348 Specifications

Transcript
Option
2,
No waste
disposer
Option
2.
Attach drain hose to air gap with large spring-type
clamp.
If the drain hose was cut, use a 1-1/2" to 2"
(3.8 to 5 cm) screw-type
clamp s,
Use a rubber
type clamps*
if needed
air gap:
Cut end of drain
section).
3.
hose
- with
1.
(do not cut
ribbed
No waste
Cut end
section).
2.
Attach
of drain
drain
disposer
hose
hose
(3.8 to 5 cm)
- no air gap:
if needed
to waste
screw-type
(do not cut ribbed
tee with
clamp
1-1/2" to 2"
s.
This connection
must be before the drain trap and at
least 20" (50.8 cm) above the floor where
dishwasher
will be installed.
It is recommended
that the drain hose
hose connector*
with spring
or screwto connect
air gap to waste tee.
This connection
must be before the drain
least 20" (50.8 cm) above the floor where
will be installed.
4,
1.
be looped
up and
the counter.
trap and at
dishwasher
securely
fastened
to the
underside
of
drain hose drain hose_cut
here if needed
_
cut here if needed
rubber hose
connector
__
large
spring-type
screw-type clamp
waste
tee
drain
hose
drain trap
r' Parts available
Option
from local plumbing
3, Waste disposer
1. Remove the disposer
drain hose.
2.
Attach drain
type clamp.
hose
drain hose
to disposer
plug. Do not cut end of
inlet with
large
be looped
up and securely
fastened
the counter.
large spring-type
clamp
to the underside
Option1,
_
from
_
drain
hose
local plumbing
drain hose
supply stores
there
connection
Direct
HelpfulTip:
route wire
wire
method:
Wiring
into the
the dishwasher
cabinet opening
will be easier if you
from the right side.
of
1.
Drill a 3/4" (1.9 cm)
hole in right-hand
cabinet
side, rear or
floor. Preferred
and
optional
shown.
drain hose
2.
disposer
inlet
locations
optional
locations
preferred
locations
are
Wood cabinet:
Sand
hole until smooth.
Metal cabinet: Cover
hole with grommet, not provided.
3.
Run wire into house wiring
4.
Install a U.L-listed/CSA-certified
clamp connector
(strain relief) for flexible-type
wire. If installing conduit,
attach a U.L.-listed/CSA-certified
conduit connector to
the junction box.
drain trap
Insert drain hose
through hole cut in
cabinet to the front
center of opening where
drain connection will be
made.
]
Prepare cabinet opening
where
are no existing
utility hookups
Electrical
spring-
This connection
must be before the drain trap and at
least 20" (50.8 cm) above the floor where dishwasher
will be installed.
It is recommended
that the drain hose
3.
_
I I
stores
- no air gap:
knockout
"_
I
Insert drain hose
through hole cut in
cabinet to the front
center of opening where
drain connection will be
made.
r' Parts available
supply
"_
JII
dra,n trap
3.
Insert drain hose
through hole cut in
cabinet to the front
center of opening where
drain connection will be
made.
[
[_
kJ
waste
tee
4.
'
drain hose
5.
Run other end of wire
through cabinet hole.
Cable must extend to the
right front of cabinet
opening.
junction
box.