Download Euphonix System 5 Specifications
Transcript
System 5 Control Surface/Frame Version 1.0 Part# 840-07576-01 Publish date: October 1999 Euphonix Inc. 220 Portage Avenue Palo Alto , CA 94306 Tel: (650)855-0400 Fax: (650) 855-0410 Web Page: www.euphonix.com In the interest of continued product development, Euphonix reserves the right to make improvements in this manual and the product it describes at any time, without notice or obligation. System 5, S-5, PatchNet, eMix, EuCon, R-1, Studio Hub, , Digital Studio Controller, DSC, CleaR, GainBall, SnapShot, SnapShot Automation, SnapShot Recall and Total Automation are trademarks of Euphonix Inc. TABLE OF CONTENTS Box Inventory..............................................................................................................4 Safety and Precautions..............................................................................................4 Power On Sequence ............................................................................................................................5 CE/TUV/UL/CSA ..........................................................................................................5 Component Overview.................................................................................................6 Functional Description ........................................................................................................................6 FRAME SECTION ......................................................................................7 Physical Specifications .......................................................................................................................7 Exploded View ......................................................................................................................................7 Side Panel View ....................................................................................................................................8 Dimensions and Weight ......................................................................................................................9 User Reference - Frame ...........................................................................................10 Assembling the S5 Frame .................................................................................................................10 System 5 Ethernet/Power Cable Configuration ..............................................................................17 System 5 Ethernet Cable Harness....................................................................................................18 CONTROL MODULES SECTION.............................................................20 Physical Specifications............................................................................................20 Top View - Control Modules..............................................................................................................20 Filler Modules .....................................................................................................................................21 Dimensions and Weight ....................................................................................................................22 Technical Specifications..........................................................................................22 Environmental Requirements ...........................................................................................................22 Power Requirements .........................................................................................................................22 Power Consumption ..........................................................................................................................22 Control Module Expansion Port .......................................................................................................23 General Description........................................................................................................................23 Physical Pinout ...............................................................................................................................23 DB25 Electrical Specification: ........................................................................................................25 Typical Usage:................................................................................................................................25 Alternate Usage #1:........................................................................................................................26 Alternate Usage #2:........................................................................................................................27 User Reference – Control Modules .........................................................................28 Control Module Setup........................................................................................................................28 Overview of Ethernet IP Address Allocation...................................................................................28 Self Test Procedure for CM401, CM402 and CM408 .......................................................................29 Initiating Self Test ...........................................................................................................................30 Self Test Operations.......................................................................................................................31 Top Level Test Keys.......................................................................................................................32 LED test..........................................................................................................................................33 All Switch LEDs Toggle ..................................................................................................................34 Color Toggle ...................................................................................................................................34 All Switch and Indicator LEDs Toggle ............................................................................................34 Vegas Mode ...................................................................................................................................34 S5 Control Surface/Frame Manual Page 2 Version 1.0 ©1999 Euphonix, Inc. Switch Test .....................................................................................................................................35 Intelligent Display Test ...................................................................................................................36 Knob Test .......................................................................................................................................37 Knob value display .........................................................................................................................38 Halo Test ........................................................................................................................................38 Knob meter display.........................................................................................................................38 Knob switch test .............................................................................................................................38 Expansion port switch test..............................................................................................................38 Fader Test ......................................................................................................................................39 Fader Test (continued) ...................................................................................................................40 All fader up .....................................................................................................................................41 All fader down.................................................................................................................................41 Fader cycle test with speed control ................................................................................................41 Fader echo test...............................................................................................................................41 Touch Sense Test ..........................................................................................................................41 Backstop PFL switch test ...............................................................................................................41 Fader Write value display...............................................................................................................41 Fader Read value display...............................................................................................................41 TFT backlight brightness test .........................................................................................................41 CPU Test .............................................................................................................................................42 RAM Test........................................................................................................................................42 ROM Test .......................................................................................................................................42 PC104 RAM Test............................................................................................................................43 APPENDIX 1.............................................................................................45 Parts Lists .................................................................................................................45 System 5 Leg Set: Part# 946-07220-01 ........................................................................................45 System 5 Frame Set, 6ft: Part# 946-06425-01 .............................................................................47 System 5 Frame Set, 9ft: Part# 946-06840-01 .............................................................................48 System 5 Frame Set, 12ft: Part# 946-07160-01 ...........................................................................49 S5 Control Surface/Frame Manual Page 3 Version 1.0 ©1999 Euphonix, Inc. Box Inventory Description Part # 946-07220-01 S5 Leg Set 726-06398-01 Leg, Left, Finished 726-06419-01 Leg, Right, Finished 726-06415-01 Keyboard Tray Assembly 726-07216-01 Keyboard Palm Rest 840-07576-01 S5 Control Surface/Frame Manual One of the following Frame Kits 946-06425-01 Frame, 6ft 946-06840-01 Frame, 9ft 946-07160-01 Frame, 12ft The specified number of the following modules: 946-05718-01 CM401 946-05719-01 CM402 946-05717-01 CM408 946-07000-01 CM409-HTP 032-07169-00 Serial Mouse Extender CM409-H 946-06650-01 CM409-F 946-06651-01 Qty 1 1 1 1 1 Safety and Precautions 1) Read Instructions - Read all the safety and operation instructions before operating the System 5 Control Surface. 2) Heed Warnings – Follow all warnings on the Control Modules and in these operating instructions. 3) Water and Moisture – Do not use the Control Surface near water. 4) Heat – Locate the Control Surface away from heat sources. 5) Power Sources – Connect the Control Modules only to a power supply of the type described in these operation instructions or as marked on the Control Modules. 6) Power Cord Protection – Route power cords so that they are not likely to be walked upon or pinched by items placed on them. 7) Object and Liquid Entry – Do not drop objects or spill liquids on the Control Surface. 8) Damage Requiring Service – The Control Modules should be serviced only by qualified personnel when: a) Objects have fallen, or liquid has spilled into the Control Modules; or b) A Control Module does not appear to operate or exhibits a marked change in performance; or, c) A Control Module has been dropped or sustained other physical damage. S5 Control Surface/Frame Manual Page 4 Version 1.0 ©1999 Euphonix, Inc. 7) Servicing – Do not attempt to service the Control Modules beyond those means described in this operation manual. All other servicing should be referred to the Euphonix Tech Support department. 8) Fuse replacement – To prevent electric shock and avoid risk of fire, replace fuse only with the same type and rating. 9) To prevent electric shock, do not use the Control Modules polarized plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure. 10) Grounding or Polarization – Do not defeat the grounding or polarization of the Control Modules. Power On Sequence The Control Surface modules are powered up by a switch on the back of the frame. The Control Surface should be powered up after the Virtual Mixer is running. CE/TUV/UL/CSA CE documentation is available. S5 Control Surface/Frame Manual Page 5 Version 1.0 ©1999 Euphonix, Inc. Component Overview Functional Description The System 5 Console consists of a frame and leg assemblies which house a configurable number of Control Modules that comprise the Control Surface. The System 5 Control Surface is the digital control center for all the System 5 component assemblies. The Control Surface communicates with the System 5 component assemblies via Ethernet network connections. Control signals are transmitted to the Euphonix EH224 EuCon Hub and distributed to the various System 5 component assemblies. No audio passes through the Control Surface. Available in 6 foot, 9 foot, and 12 foot frame widths, the System 5 Control Surface is modular in construction. The number and variety of Control Modules are configurable based on the specific needs of each facility. Control modules are 12 inches wide. Filler modules can be ordered in full or half width. S5 Control Surface/Frame Manual Page 6 Version 1.0 ©1999 Euphonix, Inc. FRAME SECTION Physical Specifications 21 15 1 13 2 16 18 7 19 10 3 Exploded View Item No. Qty Description 1 1 Leg, Right, Finished 2 2 Box beam 3 1 Leg, Left, Finished 7 1 Palm beam 10 4 Caster Brackets 13 1 Back beam-9 15 2 Brace 1 16 3 Cover, back, 3ft 18 1 Leg panel 19 1 Keyboard Tray Assy 21 1 CM401 assembly 21 * CM402 assembly 21 * CM408 assembly 21 * CM409F assembly 21 * CM409H assembly * Qty depends on specified configuration S5 Control Surface/Frame Manual Part No. 6ft 726-06399-01 Part No. 9ft 726-06419-01 726-06437-01 726-06398-01 726-06415-01 Part No. 12ft 726-07164-01 726-06408-01 726-06430-01 726-07163-01 726-06404-01 726-06686-01 (1) 726-06686-01 (2) 726-06686-01 (3) Left – 726-06394-01 Right – 726-06826-01 726-06415-01 946-05718-01 946-05719-01 946-05717-01 946-06651-01 946-06650-01 Page 7 Version 1.0 ©1999 Euphonix, Inc. Side Panel View 41” 27 30.5” 13 21 6 7 15 16 2 39.5” 8 19 29.5” 2 18 24.2” 22 Item No. Qty Description 2 2 Box Beam 6 1 Plate, compression 7 2 Palm Beam 8 1 Plate, spread 12 4 Caster 13 1 Back beam 15 2 Brace 16 * Cover, back, 3ft 18 2 Leg Panel 19 1 Keyboard Tray Assy 21 1 CM401 assembly 21 * CM402 assembly 21 * CM408 assembly 21 * CM409F assembly 21 * CM409H assembly 22 4 Foot, level 27 1 Talk Back Mic * Qty depends on specified configuration S5 Control Surface/Frame Manual 12 Part No. 6ft 726-06399-01 726-0403-01 726-06408-01 726-06411-01 726-06686-01 (2) 726-06394-01 (Left) Page 8 Part No. 9ft 726-06437-01 726-06402-01 726-07168-01 726-06404-01 726-06407-01 726-06430-01 Part No. 12ft 726-07164-01 726-07162-01 726-07163-01 726-06686-01 (3) 726-06686-01 (4) 726-06826-01 (Right) 726-06415-01 946-05718-01 946-05719-01 946-05717-01 946-06651-01 946-06650-01 000-06434-00 302-07044-00 Version 1.0 ©1999 Euphonix, Inc. Dimensions and Weight Height: 39.5 inches Width: Frame size + 10” Depth: 41 inches Weight: Frame without modules 6ft Frame: 245lbs (111kg) 9ft Frame: 300lbs (136kg) 12ft Frame: 380lbs (172kg) Approximately 14 inches of depth should be left behind the System 5 Control Surface for cable connections. S5 Control Surface/Frame Manual Page 9 Version 1.0 ©1999 Euphonix, Inc. User Reference - Frame Assembling the S5 Frame Tools required: • • • • • • • Hex drivers, 1/8”, 3/16”, 7/32”, ¼”, 5/32” Flat-bladed screwdriver, ¼” Socket wrench, ½” Silicon grease for bolts (Finish Line bicycle grease works great) Aux leg (item 20, not shown on some frame drawings) Bus wire, two 24” pieces Tap set for 3/8” 24 (3/8” 16 for newer box beams) and 5/16 18 threads Minimum number of people required: 2. For a 12-foot frame, 3 people are required. Refer to the System 5 Frame drawings (pages 7-8) and the Parts Lists at the end of this manual to help with parts identification and visualization of the steps set forth in this procedure. 1) Verify that all screws and bolts have been greased. If they aren’t greased, apply silicon grease to all of them. 2) Start with inserting the middle box beam (item 2) in the left leg (item 3, Leg Left). You may have to drop the leg panel (item 18, legpnl) to get it in easily. Two people need to hold up the beam, while the third person holds up the leg. Guide the beam into the leg (flat side up). Insert a 3/8” 24x1.5 button head bolt (046-06421-00) with a 3/8” flat washer (081-07193-00) through the leg hole and into the beam, being careful not to strip the threads. Tighten the bolt fully, using a 7/32” hex driver. S5 Control Surface/Frame Manual Page 10 Version 1.0 ©1999 Euphonix, Inc. 3) After the beam is attached to the leg, the auxiliary leg (12 ft frame only, item 20) can be put underneath the beam near the center to hold it up. Secure the auxiliary leg to the beam by inserting a “T” nut (000-06690-00) into the beam, and thread a 5/16x18x0.50 screw (044-0719200) through the auxiliary leg mounting hole and into the “T” nut. 4) Insert the rear box beam (item 2) into the left leg next, using the same techniques outlined in step 2. The auxiliary leg can help to hold up the beam. S5 Control Surface/Frame Manual Page 11 Version 1.0 ©1999 Euphonix, Inc. 5) Prior to inserting the palm beam (item 7) into the left leg, thread the bus wire through one of the holes of the spread plate (part#726-06404-01, item 8), twist-locking the wire at the spread plate end. Run the other end of the wire through its matching bolt hole on the left end of the palm beam. The spread plate should mount inside the end of the palm beam, flat side up. As the palm beam is inserted into the left leg (rounded side out) guide the bus wire into the matching bolt hole of the leg. Insert a 3/8” 24x1.5 button head bolt through the leg hole and into the beam, using the same techniques outlined in step 1. The auxiliary leg can help to hold up the beam. 6) Insert the back beam (item 13) into the left leg, using the same techniques outlined in step 1. The S5 Control Surface/Frame Manual Page 12 Version 1.0 ©1999 Euphonix, Inc. auxiliary leg can help to hold up the beam. 7) Insert as many “T” nuts in the beams as required. For example, you will need 3 “T” nuts for the middle box beam’s inner channel and 3 “T” nuts for the palm beam’s inner channel in order to install the keyboard tray. You will need 4 “T” nuts for each back cover brace (item 15, brace 1), 2 for the back beam bottom channel and 2 for the rear box beam outside channel. You will need 2 “T” nuts for each power strip, usually mounted on the rear box beam. 8) With the auxiliary leg holding up one end of the S5 frame, insert the four beams into the right leg (item 1, Leg Right), using the same techniques outlined in step 1. Also, for the palm beam, use the same technique with the spread plate and bus wire as outlined in step 4. 9) Install the four box beam braces (item 4) on each end of the box beams. Use four 5/16-18x3.5 bolts (043-06688-00) and four 5/16 lock washers (082-066889-00) for each box beam brace. Use a ½” socket wrench. Do not tighten down fully until the frame is fully loaded and its width is S5 Control Surface/Frame Manual Page 13 Version 1.0 ©1999 Euphonix, Inc. checked. 10) To secure the spread plates into the palm beam ends, pull down on the bus wire, and line up the spread plate screw holes with the leg screw holes. With a 3/16” hex driver, insert a 5/1618x1.125 flathead screw (046-06409-00) into spread plate screw hole sans the bus wire. Once the screw is threaded in and tightened down, remove the bus wire and insert the other countersunk screw in the screw hole that the bus wire previously occupied. You may have to loosen the other screw a little in order to remove the bus wire. 11) Using the 3/16” hex driver and 5/16-18x2.25 flathead screws (046-06401-00), install the spread plates (part# 726-06402-01, items 5 & 6) into the back beam ends. (Like spread plate pictured in Step 5.) 12) Install all the modules into the frame to ensure that their surfaces are flush. Use the thumbscrews (936-07240-01, S5 thumbscrew kit, 4 per module) to secure the modules to the box beams. Before installing the 401 module permanently into the frame, attach the talkback mic bracket (936-07219-01, S5 talkback mic kit) into the middle top screw hole of the SBC panel, using the screw and insulating washer supplied in the S5 talkback mic kit. 13) After verifying that the control surface is acceptable, tighten all loose screws and bolts in the frame. Tighten the bolts on the box beam braces only until their lock washers flatten, and no further. You will have to temporarily remove the modules on each end of the frame to be able to tighten the box beam braces. 14) Using a ¼” hex driver and 5/16x18x0.375 socket head screws (044-06686-00), install the back cover braces (item 15, brace 1). Determine the position of the braces by aligning them with the back cover mounting screw holes. Move the slide nuts in the rear box beam and back beam to the brace locations, and mount the braces to them. S5 Control Surface/Frame Manual Page 14 Version 1.0 ©1999 Euphonix, Inc. 15) Using a 5/32“ hex driver and 1/4x20/3/8 button head screws (044-07236-00), install the back covers on the braces. 16) Determine where the power strips (part#600-07223-00)) are going to be mounted on the rear box beam, line up the slide nuts in the box beam to match the mounting holes of the power strips, and use a ¼” hex driver with 5/16x18x0.375 socket head screws to mount the power strips into the slide nuts. 17) Determine where the keyboard drawer (item 19, kbd drawer) is going to be located, then line up the slide nuts in both box beams (the distance between the screw holes on each box beam end of the keyboard drawer is xx”). Use a ¼” hex driver with 5/16x18x0.375 socket head screws to mount the drawer into the slide nuts. S5 Control Surface/Frame Manual Page 15 Version 1.0 ©1999 Euphonix, Inc. 18) If the network, power, and talkback mic cables are not going to enter the S5 frame from the bottom of a leg, then the leg panel supporting the cabling will have to have its knockout plate removed. Remove the leg panel from the leg before punching. The punch direction should be from the outside to the inside. Support the knockout hole on the inside of the leg panel with a roll of duct tape, or something similar. This will alleviate any distortion to the leg panel metal while punching. S5 Control Surface/Frame Manual Page 16 Version 1.0 ©1999 Euphonix, Inc. System 5 Ethernet/Power Cable Configuration S5 Control Surface/Frame Manual Page 17 Version 1.0 ©1999 Euphonix, Inc. System 5 Ethernet Cable Harness 1 A1 (TYP 30 PLACES) LABEL EACH CABLE AS INDICATED (TYP BOTH ENDS) 1 2 2 3 3 5 4 (TYP 15 PLACES) 4 5 5 6 6 31.0' A1-A15 7 7 8 8 9 9 10 10 SEE DETAIL 'A' 6 12 12 13 13 3 14 14 A15 A16-A30 11 11 2 A16 1 POINT B 4 15 A30 15 POINT A 3 2 B1 MACHINE ROOM CONSOLE B2 1.0' (x15) (TYP BOTH ENDS) LABEL CABLE AS INDICATED (TYP BOTH ENDS) CONNECTOR MATING A1-A16 A2-A17 A3-A18 A4-A19 A5-A20 A6-A21 A7-A22 A8-A23 A9-A24 A10-A25 A11-A26 A12-A27 A13-A28 A14-A29 A15-A30 B1-B2 5.0' DETAIL 'A' A1-A30 WIRE LIST A1-A15 PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 PIN 7 PIN 8 A16-A30 PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 PIN 7 PIN 8 (TYP BOTH ENDS) B1-B2 WIRE LIST WIRE COLOR WHT/ORG ORG WHT/GRN BLU WHT/BLU GRN WHT/BRN BRN B1 1 2 3 B2 1 2 3 WIRE DRAIN WHITE BLACK SIGNAL GND HOT COLD CABLE ASSEMBLY PARTS LIST ITEM 1 2 3 4 5 6 QTY 30 1 1 41' 495' 31' MFR PHYCO NEUTRIK NEUTRIK GEPCO BELDEN TECHFLEX MFR P/N 1001-8P8CSR NC3FX NC3MX MP1022 BLACK MEDIA TWIST 350(1872A)BLUE CCPT6X DESCRIPTION RJ45 PLUG, 8-8, RND SLD XLR 3PIN FEMALE CABLE CONNECTOR XLR 3PIN MALE CABLE CONNECTOR 2 LEAD SHIELDED CABLE, 24AWG 4 PAIR UTP CABLE, 24AWG SOLID COPPER EXPANDABLE SLEEVING Notes: 1. All dimensions are in feet 2. Make sure that all wire ends are flush with "Point A". Typical 30 places 3. Make sure that the insulation jacket of the cable reaches to "Point B" when crimping terminal. Typical 2 places. Cable ends are to be terminated according toTIA/EIA 568b standards. S5 Control Surface/Frame Manual Page 18 Version 1.0 ©1999 Euphonix, Inc. CONTROL MODULE SECTION S5 Control Surface/Frame Manual Page 19 Version 1.0 ©1999 Euphonix, Inc. CONTROL MODULES SECTION Physical Specifications Top View - Control Modules 6’10” 5” D 12” 41” 3 A B C A 1 Frames are available in 6ft, 9ft, and 12ft sizes. Actual width of Control Surface is frame size + 10 inches. Item No. Qty Description A * CM408 Control Module B * CM402 Control Module C 1 CM401 Control Module D * TFT Display 1 1 Leg, right 3 1 Leg, left * Qty depends on specified configuration S5 Control Surface/Frame Manual Page 20 Part No. 946-05717-01 946-05719-01 946-05718-01 Inc. in CM Module 726-06419-01 726-06398-01 Version 1.0 ©1999 Euphonix, Inc. Filler Modules CM409F CM409H CM409HTP CM409F- This is the full-wide blank module for S5 Control surfaces. It can be placed anywhere within the control surface to fill up the frame. It provides a working surface for remote controls, keyboards, etc. Order part# 946-06651-01. CM409H- This module is a half-wide blank module for S5 Control surfaces. It module is similar to a CM409F but only half the width. Order part# 946-06650-01. CM409HTP- This module is a half-wide Track Panner. It is the same width as the CM409H. The CM409HTP contains a high quality track ball for panning and two switches for Pan Select/Punch and Channel Pan Function. Order part# 946-07000-01. S5 Control Surface/Frame Manual Page 21 Version 1.0 ©1999 Euphonix, Inc. Dimensions and Weight Module CM401: CM402: CM408: CM409F: CM409H: CM409HTP: Weight 35lbs (16kg) 35lbs (16kg) 35lbs (16kg) 16lbs (7kg) 9lbs (4kg) 10lbs (4.5kg) Width 12” 12” 12” 12” 6” 6” Approximately 14 inches of depth should be left behind the System 5 Control Surface for cable connections. Technical Specifications Environmental Requirements Environmental requirements for the System 5 Control Modules are as follows: Operating Temperature: 0 to 40 degrees Celsius (ambient) Storage Temperature: -10 to 55 degrees Celsius Humidity: 0 to 90% non-condensing Power Requirements 90 to 254 Volts AC (rms), 50/60Hz, 150 Watts per module. Power Consumption Power consumption of the Control Surface Modules is shown in the table below. Module CM401 CM402 CM408 Individual Module Power Consumption US (117V) Europe (230V) 1.0A .5A 1.0A .5A 1.0A .5A • Inrush current : 25 Amps • Fuse Rating: 5Amp Slo-Blo or Time Delay S5 Control Surface/Frame Manual Page 22 Japan (100V) 1.0A 1.0A 1.0A Version 1.0 ©1999 Euphonix, Inc. Control Module Expansion Port General Description On the back of each System 5 Control Module (CM401, CM402, and CM408,) is a DB25 Euphonix Expansion Port. This port is a hardware interface to external devices, and supports 8 switch inputs and 8 LED/relay drive outputs. This document describes the pinout and typical usage of this port. Physical Pinout The Expansion Port on the module is a DB25 female connector. A DB25 male cable needs to be built to interface to this port (pictured below). The pinout has been configured for easy interface to the Euphonix GP132 box, and is as shown on the following page: S5 Control Surface/Frame Manual Page 23 Version 1.0 ©1999 Euphonix, Inc. Looking into the FEMALE connector on the module: 13 1 25 14 Looking into a MALE cable connector: 1 13 14 25 Pin # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 S5 Control Surface/Frame Manual Signal LED 1 output (active low) Switch 1 input (active high) +5V LED 3 output (active low) Switch 3 input (active high) +5V LED 5 output (active low) Switch 5 input (active high) +5V LED 7 output (active low) Switch 7 input (active high) +5V +5V +5V LED 2 output (active low) Switch 2 input (active high) +5V LED 4 output (active low) Switch 4 input (active high) +5V LED 6 output (active low) Switch 6 input (active high) +5V LED 8 output (active low) Switch 8 input (active high) Page 24 Version 1.0 ©1999 Euphonix, Inc. DB25 Electrical Specification: The +5V output on the connector is protected internally by a 200mA self-resetting fuse. If LED drive outputs are used, it is recommended that several +5V connections be used to drive the anodes of the LED’s (at least one +5V wire per LED used). The active-low LED drive outputs are current limited by internal 110 ohm series resistors, and are capable of sinking 20mA each. The active-high switch inputs are TTL-level inputs with 100K pull-down resistors. Typical Usage: Currently, the software supports remote talkback switching and status on Switch inputs 1-4 and LED outputs 1-4 on the CM401 Expansion Port only. Functionality is as follows: Function Triggered by Status shown on Talkback à Mon A Switch 1 input (momentary) LED 1 output Talkback à Mon B Switch 2 input (momentary) LED 2 output Talkback à Mon C Switch 3 input (momentary) LED 3 output Talkback à Mon D Switch 4 input (momentary) LED 4 output For example, while Switch 1 is pressed down, the Talkback mic signal will be routed to the Mon A output, and LED 1 will light during the time that the switch is pressed down. Also, if Talkback à Mon A is activated from the console itself, LED 1 will also light, to indicate the status. Pressing SW1A routes the Talkback signal to Mon A, and the SW1B LED lights to indicate the TalkbackàMon A status. PINS 3, 6, 9, 12, 13, 14, 17, 20, 23 (PICK ANY 4) +5V 4 3 6 SW1A 4 3 SW1B 6 SW2A 4 3 SW2B LIGHTED SWITCH 6 SW3A 4 3 SW3B LIGHTED SWITCH 6 SW4A SW4B LIGHTED SWITCH LIGHTED SWITCH 1 2 5 1 2 5 1 2 5 1 2 5 PIN 2 PIN 1 PIN 16 PIN 15 PIN 5 PIN 4 PIN 19 PIN 18 S5 Control Surface/Frame Manual Page 25 Version 1.0 ©1999 Euphonix, Inc. Alternate Usage #1: Another way of using these talkback inputs/outputs would be to have one switch activate more than one talkback function. For example, a single switch can route the Talkback signal to all four monitor outputs: PINS 3, 6, 9, 12, 13, 14, 17, 20, 23 (PICK ANY 4) +5V 4 3 SW1A D1 D2 LED D3 LED LED D4 LED 1 2 PINS 2, 16, 5, 19 PIN 1 PIN 15 PIN 4 PIN 18 Pushing SW1A routes the Talkback signal to all four monitor outputs, and LED’s D1-D4 indicate the Talkback à Mon A-D status. S5 Control Surface/Frame Manual Page 26 Version 1.0 ©1999 Euphonix, Inc. Alternate Usage #2: Another implementation combines the above two approaches – we have individual Talkback enable buttons like in the Typical Usage, but we’ve added an ‘OMNI’ switch that routes the Talkback signal to all four monitor outputs: PINS 3, 6, 9, 12, 13, 14, 17, 20, 23 (PICK ANY 4) +5V 4 3 4 3 6 SW1A 4 3 SW1B 6 SW2A 4 3 SW2B 6 SW3A 4 3 SW3B LIGHTED SWITCH LIGHTED SWITCH 6 SW4A SW1A SW4B LIGHTED SWITCH LIGHTED SWITCH 1 2 1 2 5 1 2 PIN 1 5 1 2 PIN 15 5 1 2 5 PIN 18 PIN 4 D1 D2 1N4148 D3 1N4148 D4 1N4148 1N4148 PIN 2 S5 Control Surface/Frame Manual PIN 16 PIN 5 Page 27 PIN 19 Version 1.0 ©1999 Euphonix, Inc. User Reference – Control Modules Control Module Setup Overview of Ethernet IP Address Allocation Computer System Computer Digital Pilot Interface Pilot IP Address 192.168.0.1 192.168.0.200 192.168.0.201 192.168.0.202 192.168.0.203 192.168.0.215 Module CM401 CM402 CM408 S5 Control Surface/Frame Manual Computers Pilot ID N/A 1 2 3 4 15 Frame ID N/A N/A N/A N/A N/A N/A Control Modules IP Address Frame ID 192.168.0.24 IL 192.168.0.25 IL 192.168.0.10 IL 192.168.0.11 IL 192.168.0.12 IL 192.168.0.13 IL 192.168.0.14 IL 192.168.0.15 IL 192.168.0.16 IL 192.168.0.17 IL 192.168.0.18 IL Page 28 Module ID 0 1 2 3 15 Module ID 15 16 1 2 3 4 5 6 7 8 9 Version 1.0 ©1999 Euphonix, Inc. Self Test Procedure for CM401, CM402 and CM408 (For CM40x Firmware Rev 1.0S) The following pages describe the operation of standalone self test software for System-5 control modules. The self-test code is designed to be invoked in a module right after power-up and before the SBC downloads code into the control module 386 board. The self-test works in a fully assembled module as well as with just the upper board or just the lower board connected to the CPU board. However, the upper board must be present to run fader test modes. All the three types of control modules have the same lower board. Because of this, the lower board can be tested separately without an upper board connected. The self-test can be invoked from the lower board knobs as well as upper board self test keys. S5 Control Surface/Frame Manual Page 29 Version 1.0 ©1999 Euphonix, Inc. Initiating Self Test Enter self-test by pressing the self-test enter keys shown below. This must be done before the SBC code download. If code download from the SBC happens during self-test, then the module will automatically exit self-test and execute downloaded code. Enter Self-Test Press both Knob Switches Enter Self-Test Press both keys GpSL GpSL NonB Gp SL NonB GpSL NonB GpSL NonB Gp SL NonB GpSL NonB NonB 9 Rec 10 Rec 11 Rec 12 Rec 13 Rec 14 Rec 15 Rec Rec 17 1 Rec 18 Rec 19 Rec 20 Rec 21 Rec 22 Rec 23 Rec 24 Rec25 Rec 26 Rec 27 Rec 28 Rec 29 Rec 30 Rec 31 Rec 32 Rec 33 Rec 34 Rec 35 Rec 36 Rec 37 Rec 38 Rec 39 Rec 40 Rec 41 Rec 42 Rec 43 Rec 44 Rec 45 Rec 46 Rec 47 Rec 48 Rec GpSL NonB Rec A 2 3 Rec B Rec C 4 Rec D Record Machine 5 Rec E F All Repro All Input 6 Rec 7 Rec G Boom Boom Boom Boom Boom Boom 2 Boom 4 Rec H Record Safe 6 J Rec Ready R-1 Boom 8 K Grp Route Pan M Mix Route N P Flts Q R S Pan to: Pan to: Grp Buses Mix Buses Route to Sections Ins 16 Gp SL Btyp NonB Brng Boom Btrm Mon D Source Mon C Source Reverse Route Dyn EQ Mon B Source PanR PanR Pa n R PanR PanR Pa n R PanR PanR Su r r Su r r Surr Su r r Su r r Surr Su r r Su r r 1 3 5 78 F1tp F1 F F2 F F2tp Pa n R At y p Surr Ar n g Mon A Source Assign Knobs DivF DivF DivF DivF DivF DivF DivF DivF Au x In Dyn In Clarinet Slct/Pnch cfg xDpt P1 xHys Knob Values cDpt P2 P3 P4 P5 LoQ cGMU flts In EQ In Slct/Pnch Store P L4 L3 L2 L1 T2 T1 cfg lmQ hmQ HiQ At r m DivF FocF FocF FocF FocF FocF FocF FocF xAtk xRls cAtk cRls LoF lmF hmF HiF FocF Dly Pa n F PanF PanF Pa n F Pa n F PanF Pa n F Pa n F xRat xThr cRat cThr LoG lmG hmG HiG PanF Inpt CR Output LR phase L FocF Solo Ctrl Comms Ctrl Li C Ri R Sl Sr B CR Source Main Spkrs Alt 1 Spkrs Control Room Dim cfg cpy pst cfg cpy pst cfg cpy pst cfg cpy pst cfg cpy pst cfg cpy pst cfg cpy pst cfg cpy * * Insrt In Input Input Dyn In Aux Aux Pan to: Aux Pan to: Pan Aux Pan to: Pan route M I X G R P route swap G R P route swap G R P route swap G R P On solo route swap G R P On route swap G R P Name On Name On solo Name Name On solo On solo Name On solo Name Name Name Name On solo Name On solo Name route swap Listen Name On On On On On On On solo solo solo solo solo solo solo Slate / Osc ON Input Grp Mstrs Dyn Mix Mstrs Dyn In solo Name On Name Aux route swap Name On solo Pan G R P Name On Pan to: M I X Comms Talk Aux Mstrs * Name solo Info EQ In EQ Filts Filts In Pan M I X Name solo Filts Pan to: Pan M I X cfg pst Name On solo Name EQ Aux Pan to: Pan M I X Name On solo Filts In Aux Pan to: Pan M I X Name On solo Dyn Filts Filts In Aux Pan to: Pan M I X Name On solo Name On solo Num G R P Name On solo EQ In EQ Filts Filts In Name On solo Insrt In Dyn In Dyn EQ In EQ Filts Filts In Name On solo Input Dyn In Dyn EQ In EQ Filts Filts In * Insrt In Input Dyn In Dyn EQ In EQ Filts Filts In Insrt In Input Dyn In Dyn EQ In EQ Filts Filts In * Insrt In Input Dyn In Dyn EQ In EQ Filts * Insrt In Input Dyn In Dyn EQ In EQ * Insrt In Input Dyn In Dyn EQ In Filts In * Insrt In cfg cpy pst Name * Insrt In Main Panel Alt 2 Spkrs Cut On solo Strp Slv Name On solo Grp On Cpy Name On solo Solo Name On solo Pst swap swap swap swap Aux Pan to: solo Pan ALL Strip s Scroll Page swap Name On solo Clr M I X swap swap mstrs swap swap G R P route swap M I X swap Center Strip Mix On Pass View Input Dyn Save Mix Time Display hr swap select swap select swap select swap select swap select swap select swap select swap select swap select swap select swap select swap select swap select swap select swap select swap select swap select main select Name main select Name main select Name main select Name main select Name main select Name main select Name main select Name chan select Name chan select Name chan select Name chan select Name chan select Name chan select Name chan select Name chan select Name main select Name MS S LL M solo MM S S LL solo MM S S LL solo MS S LL M solo MS S LL M solo MM S S LL solo MS S LL M solo M MS S LL solo MM S S LL solo M S M S LL solo MM S S LL solo MS S LL M solo M S M S LL solo MS S LL M solo MM S S LL solo MS S LL M solo MM S S LL solo I II min bar sec / ft beat fr / ms tick Isolate Route ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON EQ Read - + = Edit Aux Write Abs 7 8 9 Cue Write Trim 4 5 6 3 ON Fader Grand Master x x x x x x x Strips Only 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 12 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 18 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 24 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 30 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 36 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 S5 Control Surface/Frame Manual Trim + Locate Reg’s Store Curren t Store Locate Recall - 0 12 6 CM402 Trim Pan x 12 CM408 locate time All Filts Keys Preview Glide On 1 2 Move Punch ATO On 0 . Clear Enter 42 Select Start Select End Hold On 48 54 60 72 84 Fill <-- Fill --> Fill to Punch Undo Redo Pass Record Shuttle Loc Trim Reh Jog Roll Back Return Auto Punch Rec CM401 Page 30 Version 1.0 ©1999 Euphonix, Inc. Self Test Operations The operation of each key on the upper and lower board is described in this document. GpSL Gp SL NonB GpSL NonB Gp SL NonB GpSL NonB GpSL NonB Gp SL NonB NonB 9 Rec 10 Rec 11 Rec 12 Rec 13 Rec 14 Rec 15 Rec Rec 17 Rec 18 Rec 19 Rec 20 Rec 21 Rec 22 Rec 23 Rec 24 Rec25 Rec 26 Rec 27 Rec 28 Rec 29 Rec 30 Rec 31 Rec 32 Rec 33 Rec 34 Rec 35 Rec 36 Rec 37 Rec 38 Rec 39 Rec 40 Rec 41 Rec 42 Rec 43 Rec 44 Rec 45 Rec 46 Rec 47 Rec 48 1 Rec GpSL NonB Rec A 2 3 Rec B Rec C 4 Rec D Record Machine 5 Rec E F All Repro All Input 6 Rec 7 Rec G 8 Rec H Record Safe J Rec Ready R-1 K Grp Route M Mix Route N P Q R S Pan to: Pan to: Grp Buses Mix Buses Route to Sections 16 GpSL Btyp NonB Brng Mon D Source Mon C Source Reverse Route Boom 2 4 6 Pan Flts Ins Dyn EQ Boom Btrm PanR PanR 1 3 5 78 F1tp F1 F F2 F F2tp PanR At y p Surr Surr Surr Ar n g Boom Boom Boom Boom Boom Boom Boom PanR PanR PanR PanR PanR PanR Surr Surr Surr Surr Surr Surr Mon B Source Mon A Source Assign Knobs DivF DivF DivF DivF DivF DivF DivF xDpt DivF Au x In Dyn In P1 xHys flts Clarinet Slct/Pnch cfg Knob Values P2 P3 P4 P5 In Slct/Pnch Store P cDpt cGMU L4 L3 L2 L1 T2 T1 cfg EQ LoQ lmQ In hmQ HiQ DivF At r m LR phase L FocF FocF FocF FocF FocF FocF FocF FocF xAtk xRls cAtk cRls LoF lmF hmF HiF FocF Dly PanF PanF PanF PanF PanF PanF PanF PanF xRat xThr cRat cThr LoG lmG hmG HiG PanF Inpt Solo Ctrl Comms Ctrl Li C Ri R CR Output Sl Sr B CR Source Main Spkrs Alt 1 Spkrs Control Room Dim cfg cpy pst cfg cpy pst cfg cpy pst cfg cpy pst cfg cpy pst cfg cpy pst cfg cpy pst cfg cpy Insrt In * Insrt In Input Insrt In Input Dyn In Aux Input Input route M I X G R P route swap M I X G R P route swap M I X G R P Aux route swap M I X G R P route swap route swap Name On On solo solo Name Name Name Name Filts Name Name Name Name Name route swap Listen Name Name On On On On On On On On solo solo solo solo solo solo solo solo Slate / Osc Input Grp Mstrs Dyn Mix Mstrs EQ In EQ Filts Filts In Name Aux Pan to: G R P route swap Name Name Name Strp Slv Name On Solo Cpy Name Pst Name swap swap swap Pan ALL Strip s Scroll Page swap Aux Pan to: solo solo Clr M I X swap Name On On On solo solo solo solo solo Grp On On On On On solo Pan M I X Talk Aux Mstrs * Dyn In solo solo solo Name On On On On solo solo solo solo Name On On On On solo Name Comms Info ON Insrt In Name cfg pst Name On solo Name EQ Pan G R P Name On solo Dyn Aux M I X Name On solo Input Pan to: Pan G R P Name On solo Filts In Aux Pan to: M I X Name On solo Num G R P Name On solo EQ In Filts Filts In Pan * Dyn In Dyn EQ Filts Pan to: Insrt In EQ In EQ Filts In Pan * Dyn In Dyn Filts Pan to: Pan Insrt In EQ In EQ Aux Pan to: Pan * Dyn In Dyn Filts In Aux Pan to: Pan Input Filts Filts In Aux Pan to: Insrt In EQ In EQ Filts Filts In * Dyn In Dyn EQ In EQ Filts Filts In Insrt In Dyn In Dyn EQ In EQ Filts * Input Dyn In Dyn EQ In EQ Filts In Insrt In Input Dyn In Dyn EQ In * cfg cpy pst Name * Main Panel Alt 2 Spkrs Cut swap swap mstrs swap swap G R P route swap M I X swap Center Strip Mix On Pass View Save Mix Time Display hr swap select swap select swap select swap select swap select swap select swap select swap select swap select swap select swap select swap select swap select swap select swap select swap select swap select main select Name main select Name main select Name main select Name main select Name main select Name main select Name main select Name chan select Name chan select Name chan select Name chan select Name chan select Name chan select Name chan select Name chan select Name main select Name MM S S LL solo MS M S LL solo MS M S LL solo MM S S LL solo MS M S LL solo MS M S LL solo MS M S LL solo M MS S LL solo MS M S LL solo M S M S LL solo MM S S LL solo S LL MM S solo MS S L M L solo MM S S LL solo MS S L M L solo MM S S LL solo MM S S LL solo I II Input min bar Dyn sec / ft beat fr / ms tick Isolate Route ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON EQ All Filts Keys Read - + = Edit Aux Write Abs 7 8 9 Cue Write Trim 4 5 6 3 ON Fader Grand Master x x x x x x x Strips Only 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 12 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 18 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 24 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 30 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 36 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 S5 Control Surface/Frame Manual Trim + Locate Reg’s Store Locate Recall - 0 Preview Glide On 1 2 Move Punch ATO On 0 . Clear Enter 42 Select Start Select End Hold On 48 54 60 72 84 Fill <-- Fill --> Fill to Punch Undo Redo Pass Record Shuttle Loc Trim Reh Jog Roll Back Return Auto Punch Rec CM401 CM402 Upper Board Test Keys Trim Store Curren t Pan x 12 CM408 locate time Lower Board Test Keys Page 31 Version 1.0 ©1999 Euphonix, Inc. Top Level Test Keys To enter the 6 different tests, use the keys shown below. After entering the test, use the detailed description of each test on the following pages to navigate through different test modes within a test. CPU Board tests cpy cfg CPU test pst LED test * Knob test Switch test LED test Display test Exit Test Fader test Switch Test Insrt In Input Display Test Dyn In Dyn On On On On solo solo solo solo Num Grp Slv Strp On Solo C Knob Test EQ In EQ Filts Filts In CM402 Fader Test Aux Exit Test /Exit to main Pan to: Pan CM401/CM408 LoF LoQ Knob Test LED Test LoF LoQ All LEDs Toggle Halo LEDs Cycle Test LoF LoQ Press Together to Exit Test/Exit to top-level tests Lower Board S5 Control Surface/Frame Manual Page 32 Version 1.0 ©1999 Euphonix, Inc. LED test The LED test has the following modes; • Toggle upper board LEDs • Toggle all LEDs • LED color test • Vegas mode All Switch LEDs toggle All Upper LEDS toggle * Color Toggle Color toggle Input Dyn EQ All Switch and Indicator LEDs toggle Vegas Mode/Vegas Mode fader cycle toggle Num Aux Pan All Upper & Lower LEDs toggle swap Exit Test Key/Exit to main Grp Slv swap Exit Test Vegas Mode Strp On Solo swap CM402 CM401/CM408 LoF LoQ LED Color Toggle Test LoF LoQ All LEDs Toggle Halo LEDs Cycle Test LoF LoQ Press Together to Exit Test/Exit to top-level tests Lower Board S5 Control Surface/Frame Manual Page 33 Version 1.0 ©1999 Euphonix, Inc. All Switch LEDs Toggle This switch toggles all the upper board LEDs on and off. This mode times out after 5 mins if all LEDs are left ON and goes into Vegas mode. Color Toggle This switch cycles between the same color LEDs in the following order • Green • Red • Yellow • Orange • Blue All Switch and Indicator LEDs Toggle This toggles all the upper and lower board LEDs including the daughter board LEDs. NOTE: For thermal reasons, the module should not be left with all LEDs On. Use Vegas mode for burn-in. For protection, the module will time out into Vegas mode if all LEDs are left ON for more than 5 minutes. Vegas Mode Flashes alternate LEDs on and off. The default Vegas mode also puts the fader into cycle test. Repeated presses of this key toggles the fader cycle on/off. If left running, the fader cycle will time out after 5 minutes. S5 Control Surface/Frame Manual Page 34 Version 1.0 ©1999 Euphonix, Inc. Switch Test Switch test has the following modes; Momentary switch press - This tests lights up the switch LED of a switch while it is pressed. * Input Dyn EQ Aux Exit Test Key/Exit to main Pan CM402/CM408 Exit Test Num Grp swap Strp Slv swap On Solo swap Cpy Pst swap CM402 S5 Control Surface/Frame Manual Page 35 Version 1.0 ©1999 Euphonix, Inc. Intelligent Display Test Display bit test – This test lights up the whole of the intelligent display. It dims the displays for the duration of this test to protect them from overheating and burnout. Display text - This test shows a text on each intelligent display, which happens to be the hexadecimal display number in the software map. This test is not accessible from the lower board. Display bits test * Display text test Input Dyn EQ Aux Exit Test Key/Exit to main Pan CM402/CM408 Display Bits Test Exit Test Display Text Test Num Grp swap Strp Slv swap On Solo swap Cpy Pst swap CM402 S5 Control Surface/Frame Manual Page 36 Version 1.0 ©1999 Euphonix, Inc. Knob Test • Halo Test • Knob value display • Knob meter display • Knob switch test • Expansion port switch test * Input Knob Halo Test/Halo Test Setup Knob Knob Halo Meters test Knob Display Value Display Knob Meters Display Exit Test Knob Test Dyn Num EQ Aux Pan swap Exit Test Key/Exit to main Grp Slv swap Strp On Solo swap CM402 CM401/CM408 LoF LoQ LoF LoQ Knob Test Halo LEDs Cycle Test/LED Cycle Step LoF LoQ Press Together to Exit Test/Exit to top-level tests Lower Board S5 Control Surface/Frame Manual Page 37 Version 1.0 ©1999 Euphonix, Inc. Knob value display Displays the hex 0 through FF value of the knob being currently moved on an intelligent display. This mode is useful for testing the CM401 spin knob. Halo Test This cycles through all the knob halo and center LEDs by turning one LED on at a time on each key press. Knob meter display Shows the knob value as a bar on the meter board (fader daughter board). Knob switch test All the knobs halo orange LEDs light up while the knob center switch is pressed. The Expansion port switches are also tested in this mode. Pressing one of the eight switches will light up its LED for as long as the key is pressed. Expansion port switch test See the Knob switch test section. S5 Control Surface/Frame Manual Page 38 Version 1.0 ©1999 Euphonix, Inc. Fader Test • All fader up • All fader down • Fader cycle test with speed control • Fader echo test • Touch Sense Test • Backstop PFL switch test • Fader Write value display • Fader Read value display • TFT backlight brightness test This test is not accessible from the lower board. All Fader Up * All Fader Down Input Fader Cycle Dyn EQ Fader Echo Aux Pan Exit Test Key/Exit to main CM401/CM408 All Fader Up Fader Cycle All Fader Down Num swap Grp Exit Test Fader Echo Strp Slv swap On swap Solo Cpy Pst swap CM402 S5 Control Surface/Frame Manual Page 39 Version 1.0 ©1999 Euphonix, Inc. Fader Test (continued) Fader Cycle Speed GpSL GpSL NonB GpSL NonB GpSL NonB GpSL NonB GpSL NonB GpSL NonB NonB 9 Rec 10 Rec 11 Rec 12 Rec 13 Rec 14 Rec 15 Rec Rec 17 1 Rec 18 Rec 19 Rec 20 Rec 21 Rec 22 Rec 23 Rec 24 Rec25 Rec 26 Rec 27 Rec 28 Rec 29 Rec 30 Rec 31 Rec 32 Rec 33 Rec 34 Rec 35 Rec 36 Rec 37 Rec 38 Rec 39 Rec 40 Rec 41 Rec 42 Rec 43 Rec 44 Rec 45 Rec 46 Rec 47 Rec 48 Rec GpSL NonB Rec A 2 3 Rec B Rec C 4 Rec D Record Machine 5 Rec E F All Repro All Input 6 Rec 7 Rec G 8 Rec H Record Safe J Rec Ready R-1 K Grp Route M Mix Route N P Q R S Pan to: Pan to: Grp Buses Mix Buses Route to Sections 16 GpSL Btyp NonB Brng Mon D Source Mon C Source Reverse Route Boom Boom Boom Boom Boom Boom Boom Boom 2 4 6 Pan Flts Ins Dyn EQ Boom Btrm PanR PanR PanR PanR PanR PanR PanR PanR 1 3 5 78 F1tp F1 F F2 F F2tp PanR At y p Mon B Source Mon A Source Surr Surr Surr Surr Surr Surr Surr Surr Assign Knobs DivF DivF DivF DivF DivF DivF DivF DivF Au x In Dyn In xDpt P1 xHys Knob Values Clarinet Slct/Pnch cfg cDpt P2 P3 P4 P5 LoQ cGMU flts In EQ In Slct/Pnch Store P Surr Ar n g DivF At r m L4 L3 L2 L1 T2 T1 cfg lmQ hmQ HiQ FocF FocF FocF FocF FocF FocF FocF xAtk xRls cAtk cRls LoF lmF hmF HiF FocF Dly PanF PanF PanF PanF PanF PanF PanF PanF xRat xThr cRat cThr LoG lmG hmG HiG PanF Inpt CR Output LR phase L FocF Solo Ctrl Comms Ctrl Li C Ri R Sl Sr B CR Source Main Spkrs Alt 1 Spkrs Control Room Dim cfg cpy pst cfg cpy pst cfg cpy pst cfg cpy pst cfg cpy pst cfg cpy pst cfg cpy pst cfg cpy Insrt In Insrt In Input * * Insrt In Input Dyn In Input Dyn In Filts In Filts In Aux Aux Pan to: Aux Pan to: Pan route M I X G R P route swap swap select M I X G R P route swap swap select G R P route swap swap select G R P route swap swap select G R P route swap swap select G R P On solo On Name Name On Name On solo Name On solo On solo Name Name Name Name On solo Name Name Name On solo Name On solo Name Listen Name On On On On On On On solo solo solo solo solo solo solo Slate / Osc ON Insrt In Input Grp Mstrs Dyn Mix Mstrs Dyn In solo Name On solo Name Aux G R P On route swap swap select Comms Talk Aux Mstrs * EQ In EQ Filts Filts In Name Name On solo Pan M I X cfg pst Info Cut Name On solo solo Filts Pan to: route swap swap select Name On solo Name EQ Pan M I X Name On solo Dyn Pan to: Pan M I X Name On solo Input Aux Pan to: Pan M I X Name On solo Filts In Aux Pan to: Pan M I X Name On solo Name On solo Num G R P Name On solo EQ In Filts Filts In Aux Pan to: Pan * Dyn In Dyn EQ Filts In Aux Pan to: Pan Input Filts Filts In Insrt In EQ In EQ Filts Filts In * Dyn In Dyn EQ In EQ Filts Filts In Input Dyn EQ In EQ Filts Insrt In Dyn In Dyn EQ In EQ Filts * Insrt In Dyn In Dyn EQ In EQ Filts * Input Dyn In Dyn EQ In EQ Insrt In Input Dyn In Dyn EQ In Insrt In * cfg cpy pst Name * Main Panel Alt 2 Spkrs On solo Strp Slv Name On solo Grp On Cpy Name On solo Solo Name swap swap select swap swap select swap swap select swap solo Pan ALL Strip s Scroll swap swap select Aux Pan to: On solo Clr Page swap swap select Name On solo Pst M I X swap select swap mstrs swap swap select swap G R P route swap swap select swap select M I X swap Center Strip Mix On Pass View Input Dyn Save Mix Time Display hr swap select I II min bar sec / ft beat fr / ms tick Isolate main select Name MS S LL M solo main select Name S LL MM S solo main select Name S L MM S L solo main select Name MS S LL M solo main select Name MS S LL M solo main select Name S L MM S L solo main select Name MS S LL M solo main select Name M MS S LL solo chan select Name S L MM S L solo chan select Name M S S LL M solo chan select Name S L MM S L solo chan select Name MS S LL M solo chan select Name M S S L M L solo chan select Name MS S LL M solo chan select Name S L MM S L solo chan select Name MS S LL M solo main select Name S L MM S L solo Route ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON EQ All Keys Filts Read - + = Edit Aux Write Abs 7 8 9 Cue Write Trim 4 5 6 3 ON Fader Grand Master x x x x x x x locate time Trim + Locate Reg’s Store Locate Recall - Pan x Strips Only 0 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 12 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 18 Preview Glide On 1 2 Move Punch ATO On 0 . Clear Enter 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 24 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 30 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 36 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 42 Select Start Select End Hold On 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 36 42 48 60 72 48 54 60 72 84 Fill <-- Fill --> Fill to Punch Undo Redo Pass Record Shuttle Loc Trim Reh Jog LED Auto Punch Rec solo MS S LL M Touch Sense Return Roll Back Backstop PFL switch LED Fader Read/Write Value Display Upper Display = Read Value Lower Display = Write Value Trim Store Curren t ON 12 6 0 6 S5 Control Surface/Frame Manual Page 40 Version 1.0 ©1999 Euphonix, Inc. All fader up All faders all the way up All fader down All faders all the way down Fader cycle test with speed control All faders cycle up and down at the speed determined by the speed control knob. The speed control knob also varies the brightness of the TFT backlight when in this test. It should vary from all the way off to the brightest setting. This fader cycle test times out after 5 minutes to protect the faders from burn-out. Fader echo test All faders follow the one fader touched. Touch Sense Test Self-test touch sense LED lights up when a fader is touched. This mode is always active in fader test mode. Backstop PFL switch test Self test backstop PFL LED lights up when a fader is pulled back to enable its backstop PFL switch. This mode is always active in fader test mode. Fader Write value display Any value written to a fader is displayed in its designated fader write intelligent display. This mode is always active in fader test mode. Fader Read value display All faders are continuously read and the read value is displayed in its designated fader read intelligent display. This mode is always active in fader test mode. TFT backlight brightness test See Fader cycle test. S5 Control Surface/Frame Manual Page 41 Version 1.0 ©1999 Euphonix, Inc. CPU Test RAM Test This tests the upper unused portion of the CPU board RAM. Watch for the ‘Pass’ display to show up when the test is done. ROM Test This test reads the ROM and computes and checksum and displays it. The user/tester can match the checksum to a known good checksum to make sure ROM test is successful. Checksum (version 1.0S): CM401 996C CM402 33ae CM408 C38e S5 Control Surface/Frame Manual Page 42 Version 1.0 ©1999 Euphonix, Inc. PC104 RAM Test This test writes and reads the whole PC104 RAM and checks for errors. Watch for the ‘Pass’ display to show up when the test is done. S5 Control Surface/Frame Manual Page 43 Version 1.0 ©1999 Euphonix, Inc. RAM Test * ROM Test Input PC104 RAM Test Dyn EQ Aux Exit Test Key/Exit to main Pan CM401/CM408 RAM Test PC104 RAM Test Exit Test ROM Test Num swap Grp Slv Strp swap On swap Solo Cpy Pst swap CM402 S5 Control Surface/Frame Manual Page 44 Version 1.0 ©1999 Euphonix, Inc. APPENDIX 1 Parts Lists System 5 Leg Set: Part# 946-07220-01 Item# Item Description Qty 726-06398-01 726-06846-01 726-06394-01 726-06415-01 726-06493-01 041-06290-00 726-06791-01 000-06790-00 420-04065-00 600-06387-00 600-00728-00 110-05551-00 726-06419-01 726-06847-01 726-06826-01 042-05677-00 048-00929-00 046-06073-00 726-06405-01 06406-01 726-06407-01 726-06838-01 044-06686-00 081-06417-00 726-06832-01 000-06434-00 600-06991-00 030-06993-01 030-06994-01 030-06995-01 030-06996-01 030-06997-01 030-06998-01 030-06999-01 006-04969-00 049-00838-00 032-07207-00 030-07199-01 Leg-Left-Finished S5 Leg-Left-Machined S5 Panel-Weldment-Left Leg Keyboard Tray Assy Track-Keyboard Top S5 10x32x1/4 Pan/Phil/Cz Track-Keyboard Base S5 Glide-Keyboard S5 Dpdt-20a Rocker Iec320/C14 Power Entry Line Filter/Am Coupler Rj45 Panel Mount Leg-Right-Finished S5 Leg-Right-Machined S5 Panel-Weldment-Right 6-32x3/16 Flat/Phil/Clrznc 6-32x3/8 Pan/Phil/Sem-Ext/Clr 4-40x1/4l Pan/Phl/Clr Zinc Bracket-Rear Caster Bracket-Front Caster Caster-36mm Spacer-Left-S5 Cm 5/16-18x.375 Bolt Socket #10 Flat Washer-Brass Ac Cover S5 Leveling Pad-5/16-18 Iec320/C13 Power Outlet Ca-Ac Line-S5 Frame Ca-Ac Neutral-S5 Frame Ca-Ac Gnd-S5 Frame Ca-Outlet Ac Line-S5 Frame Ca-Outlet Ac Neutral-S5 Ca-Sw Line-S5 Frame Ca-Sw Neutral-S5 Frame Label-Universal Ground 6-32 Kepnut/Ext/Clr Zinc Ca-Pwr/Iec/N-Usa/8ft/15a Ca-Door Support-S5 1 1 1 1 1 8 1 2 1 1 1 12 1 1 1 14 4 4 2 2 4 1 8 2 2 4 3 1 1 5 1 1 1 1 1 12 1 4 S5 Control Surface/Frame Manual Page 45 Version 1.0 ©1999 Euphonix, Inc. Parts List (cont) 000-07194-00 044-06686-00 041-07074-00 041-00917-00 002-07316-00 726-07216-01 084-00939-00 046-07331-00 S5 Control Surface/Frame Manual 1.5" Grommet 5/16-18x.375 Bolt Socket 10-24x3/8l Pan/Phil/Cz 10-32x.125l Skt/Shldr/Ss Cable-Strap Kbd Palmrest-S5 #10 Washer Ext Star/Clr Zinc 10-32x3/8 Button/Skt/Ss Page 46 1 8 16 8 1.6 1 8 8 Version 1.0 ©1999 Euphonix, Inc. Parts List (cont) System 5 Frame Set, 6ft: Part# 946-06425-01 Item# Item Description Qty 726-06399-01 726-06400-01 726-06408-01 726-06402-01 726-06403-01 726-06404-01 726-06411-01 726-06686-01 600-07223-00 032-07147-00 032-07148-00 032-07149-00 032-07150-00 081-07193-00 936-07218-01 043-06688-00 082-06689-00 046-06401-00 046-06421-00 081-07193-00 936-07241-01 044-07236-00 936-07239-01 000-06690-00 044-06686-00 936-07240-01 040-06833-00 030-07394-01 Beam-Box 6ft S5 Clamp-Beam Beam-Back 6ft S5 Plate-Back Beam Palm Rest-6ft S5 Plate-Palm Beam Brace-Back Cover-Back 3ft Power Strip-Iec320-6pos Iec320 Jumper Cordset-0.5m Iec320 Jumper Cordset-1.0m Iec320 Jumper Cordset-1.5m Iec320 Jumper Cordset-2.5m 3/8 Flat/Wash/Ss S5 Frame Bolt Kit 5/16-18x3.5 Bolt Hex-Head-Zi 5/16 Lockwasher 5/16-18x2.25 Bolt Flat/Soc/Ss 3/8-16x1.25l Buttonhd/Skt/Ss 3/8 Flat/Wash/Ss S5 Rear Panel Bolt Kit ¼-20x3/8 B4cs S5 Tee Hardware Kit 5/16-18x.375 Tee Nut/Cz 5/16-18x.375 Bolt Socket Hd/Cz S5 Thumb Screw Kit 10-32x3/8 Thumb\Washer Face Ca-Internal Ethernet/6ft 2 4 1 2 1 2 1 2 2 5 3 2 1 8 1 16 16 8 8 8 1 20 1 22 22 7 4 1 S5 Control Surface/Frame Manual Page 47 Version 1.0 ©1999 Euphonix, Inc. Parts List (cont) System 5 Frame Set, 9ft: Part# 946-06840-01 Item# Item Description Qty 726-06437-01 726-06400-01 726-06439-01 726-06402-01 726-07168-01 726-06404-01 726-06411-01 726-06686-01 600-07223-00 032-07147-00 032-07148-00 032-07149-00 032-07150-00 030-07180-01 936-07218-01 043-06688-00 082-06689-00 046-06401-00 046-06421-00 081-07193-00 936-07241-01 044-07236-00 936-07239-01 000-06690-00 044-06686-00 936-07240-01 040-06833-00 Beam-Box 9ft S5 Clamp-Beam Beam-Back 9ft S5 Plate-Back Beam Palm Rest-9ft S5 Plate-Palm Beam Brace-Back Cover-Back 3ft Power Strip-Iec320-Reworked Iec320 Jumper Cordset-0.5m Iec320 Jumper Cordset-1.0m Iec320 Jumper Cordset-1.5m Iec320 Jumper Cordset-2.5m Ca-Internal Ethernet/9ft S5 Frame Bolt Kit 5/16-18x3.5 Bolt Hex-Head-Zi 5/16 Lockwasher 5/16-18x2.25 Bolt Flat/Soc/Ss 3/8-16x1.25l Buttonhd/Skt/Ss 3/8 Flat/Wash/Ss S5 Rear Panel Bolt Kit ¼-20x3/8 B4cs S5 Tee Hardware Kit 5/16-18x.375 Tee Nut/Cz 5/16-18x.375 Bolt Socket Hd/Cz S5 Thumb Screw Kit 10-32x3/8 Thumb\Washer Face 2 4 1 2 1 2 2 3 2 5 3 2 1 1 1 16 16 8 8 8 1 20 1 22 22 10 4 S5 Control Surface/Frame Manual Page 48 Version 1.0 ©1999 Euphonix, Inc. Parts List (cont) System 5 Frame Set, 12ft: Part# 946-07160-01 Item# Item Description Qty 726-07164-01 726-06400-01 726-07163-01 726-06402-01 726-07162-01 726-06404-01 726-06411-01 726-06686-01 600-07223-00 032-07147-00 032-07148-00 032-07149-00 032-07150-00 936-07218-00 043-06688-00 082-06689-00 046-06401-00 046-06421-00 081-07193-00 936-07241-01 044-07236-00 936-07239-01 000-06690-00 044-06686-00 936-07240-01 040-06833-00 936-07237-01 726-06416-01 000-06434-00 000-06690-00 044-07192-00 030-07395-01 Beam-Box-12ft S5 Clamp-Beam Beam-Back-12ft S5 Plate-Back Beam Palm Rest-12ft S5 Plate-Palm Beam Brace-Back Cover-Back 3ft Power Strip-Iec320-6pos Iec320 Jumper Cordset-0.5m Iec320 Jumper Cordset-1.0m Iec320 Jumper Cordset-1.5m Iec320 Jumper Cordset-2.5m S5 Frame Bolt Kit 5/16-18x3.5 Bolt Hex-Head-Zi 5/16 Lockwasher 5/16-18x2.25 Bolt Flat/Soc/Ss 3/8-16x1.25l Buttonhd/Skt/Ss 3/8 Flat/Wash/Ss S5 Rear Panel Bolt Kit 1/4-20x3/8 B4cs S5 Tee Hardware Kit 5/16-18x.375 Tee Nut/Cz 5/16-18x.375 Bolt Socket Hd/Cz S5 Thumb Screw Kit 10-32x3/8 Thumb\Washer Face S5 Aux Leg Kit Leg-Auxiliary S5 Leveling Pad-5/16-18 5/16-18x.375 Tee Nut/Cz 5/16-18x.50 Bolt Socket Hd Ca-Internal Ethernet/12ft 2 4 1 2 1 2 3 4 3 5 3 2 1 1 16 16 8 8 8 1 20 1 22 22 13 4 1 1 2 8 8 1 S5 Control Surface/Frame Manual Page 49 Version 1.0 ©1999 Euphonix, Inc.